Search Results

Search found 14951 results on 599 pages for 'connect by'.

Page 474/599 | < Previous Page | 470 471 472 473 474 475 476 477 478 479 480 481  | Next Page >

• Linux on Sony Vaio VPCEB1S1E

  - by Jaakko

  I bought Sony Vaio VPCEB1S1E and I was able to surf on net. Then I tried to install Ubuntu 9.04 and Linux Mint on it but neither allows me an access to the Internet. How can I configure Mint so that I can go to net and get updates via apt-get? jaakko@jaakko-laptop ~ $ ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 46:83:d4:f4:36:bc BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 78:dd:08:c5:61:88 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster0 Link encap:UNSPEC HWaddr 78-DD-08-C5-61-88-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) jaakko@jaakko-laptop ~ $ ping 8.8.8.8 connect: Network is unreachable

  Read the article

• Enabling WinRM by Group Policy

  - by SaintNick

  I'm having partial success enabling WinRM through Active Directory GPO's on our Server 2008 R2 environment. I've created a GPO that enables "Allow automatic configuration of listeners" and also enables all the necessary predefined WinRM Firewall rules. This GPO works fine for our webservers. Indeed, this is reflected by the "Server Manager Remote Management" nicely flipping to "enabled" in Server Manager Server Summary. However, the same GPO applied to both our Management servers, which are Domain Controllers, does not give the same result. I see the GPO settings being applied, including the listener as confirmed by C:\Windows\system32>winrm e winrm/config/listener Listener [Source="GPO"] Address = * Transport = HTTP Port = 5985 Hostname Enabled = true URLPrefix = wsman CertificateThumbprint ListeningOn = 10.32.40.210, 10.32.40.211, 10.32.40.212 But in Server Manager, Server Summary, Remote Management remains on "disabled" and indeed when trying to connect to one of these machines Server Manager gives an "Access Denied". Manually enabling WinRM locally via Server Manager "Configure Server Manager Remote Management" on either of these machines works fine. What can be the cause? Can it have something to do with theses machines being DC's and needing extra settings in the GPO? Nick Reid

  Read the article

• Windows 7, network connection with no default gateway: any way to change the "Unknown network" statu

  - by e-t172

  Hi, I have a computer running Windows 7 Pro RTM. This computer has two network connections: A Wi-fi connection to the Internet (through a home router) which works just fine. An OpenVPN virtual network connection. More precisely, this is a virtual Ethernet connection which behaves exactly like a physical Ethernet wired connection. My problem is that the "Network and sharing center" shows "Unknown network" for the OpenVPN connection. After some research I found that logical networks (outside a domain) are identified by the MAC address of the default gateway of the connection. Problem is, the OpenVPN connection has no default gateway: it is a private network, so I don't need one... Consequently, the "Unknown network" is always considered public, so the firewall is always in "public mode", which I don't want. Plus, I can't rename "Unknown connection" or anything (which makes sense), so it is kinda ugly. My goal is to define a proper logical network for the OpenVPN connection with the private profile. I know of some workarounds (disable the firewall, modify security policy to make all unknown networks "private") but they're still workarounds. I just want my clients to connect to the VPN without having to disable their firewall settings, without changing global configuration with potential side-effects (the "security policy" solution) and without having to look at an ugly "Unknown connection" in the Network and sharing center. Is there any way I can do this? I tried to check what was going on in the registry (HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkList is interesting), but I still didn't find a way to "force" the OpenVPN connection to be assigned to a logical network. Any help would be very appreciated. A related question showed up at Superuser: http://superuser.com/questions/37355/windows-7-cant-identify-network/37422

  Read the article

• SSH session closing whilst virtualenv session stays open (I think)

  - by ing0

  I've been developing some sites using Flask recently (running on debian within a virtualenv), and when I am testing I can run it on a port, let's say post 5000. So I run the script like so: . env/bin/activate <- go into virtual environment python file.py <- run python script And I will be given this message: Running on http://0.0.0.0:5000/ So this all works great and I can access my site on this port fine. However... my rubbish ISP always does this thing where it resets something around 1am every morning. I have no idea what this is, everything runs like normal but I always get disconnected from any SSH sessions open. This leaves it running and all I can do is call: lsof -i Which will show me the process but if I kill it and then rerun it things get weird. The: Running on http://0.0.0.0:5000 message still shows but I cannot connect to it anymore. I've tried changing the port number and it seems the only thing that works is trying again later on or on another day. Now I'm assuming that something on my server resets inbetween these times and I would like to think it was maybe that virtualenv session timing out, but I cannot find out how to do this manually, does anyone know?

  Read the article

• Bind9 zone files

  - by user42780

  Well for the better part of the last two hours I've tried to figure out what is actually wrong, but I can't seem to find anything obvious to me. What I'm trying to do is setup my DNS for say(per example) domain.com. This should include two NS records, namely ns1.domain.com and ns2.domain.com. With that there should be a mail record, as well as a CNAME record for www. I've been trough roughly 20 how to's in the last two hours, rewrote everything from scratch four times and I still can't seem to find whats wrong. My only suspicion to this might be two things; the error I get from the bind9 daemon when I stop the service, and the named.conf file. The error I get from the bind9 daemon when stopping the service is: * Stopping domain name service... bind9 rndc: connection to remote host closed This may indicate that * the remote server is using an older version of the command protocol, * this host is not authorized to connect, * the clocks are not syncronized, or * the key is invalid. I honestly doesn't know what this means, apart from the key defined in /etc/bind/rndc.key that's not in the named.conf file(yes, I did try to add it to no avail). Here's all the zone files, and configuration files; http://208.77.101.5/bind9/ If anyone could help, it would be greatly appreciated.

  Read the article

• How to write files in specific order?

  - by Bernie

  Okay, here's a weird problem -- My wife just bought a 2014 Nissan Altima. So, I took her iTunes library and converted the .m4a files to .mp3, since the car audio system only supports .mp3 and .wma. So far so good. Then I copied the files to a DOS FAT-32 formatted USB thumb drive, and connected the drive to the car's USB port, only to find all of the tracks were out of sequence. All tracks begin with a two digit numeric prefix, i.e., 01, 02, 03, etc. So you would think they would be in order. So I called Nissan Connect support and the rep told me that there is a known problem with reading files in the correct order. He said the files are read in the same order they are written. So, I manually copied a few albums with the tracks in a predetermined order, and sure enough he was correct. So I copied about 6 albums for testing, then changed to the top level directory and did a "find . music.txt". Then I passed this file to rsync like this: rsync -av --files-from=music.txt . ../Marys\ Music\ Sequenced/ The files looked like they were copied in order, but when I listed the files in order of modified time, they were in the same sequence as the original files: ../Marys Music Sequenced/Air Supply/Air Supply Greatest Hits ls -1rt 01 Lost In Love.mp3 04 Every Woman In The World.mp3 03 Chances.mp3 02 All Out Of Love.mp3 06 Here I Am (Just When I Thought I Was Over You).mp3 05 The One That You Love.mp3 08 I Want To Give It All.mp3 07 Sweet Dreams.mp3 11 Young Love.mp3 So the question is, how can I copy files listed in a file named music.txt, and copy them to a destination, and ensure the modification times are in the same sequence as the files are listed?

  Read the article

• Computer specs for a large database

  - by SpeksETC

  What sort of computer specs (CPU, RAM, disk speed) should I use for running queries on a database of 200+ million records? The queries are for a research project, so there is only one "user" and only one query will be running at a time. I tried it on my own laptop with SQL Server with an i3 processor, 2GB RAM, 5400 RPM disk and a simple query didn't finish even after 8+ hours. I have an option to connect a SSD via eSata and upgrade to 4GB RAM, but not sure if this will be enough... Thanks! Edit: The database is about 25 GB and the indexes are not setup properly. When I tried to add an index, I let it run for about 8 hours and it still hadn't finished so I gave up. Should I have more patience :)? In general, the queries will run once in a while and its ok even if it takes a couple hours to complete.... Also, the queries will produce probably about 10 million records which I need to process using Stata/Matlab and I'm concerned that my current laptop is not strong enough, but unsure of the bottleneck....

  Read the article

• iPhone Remote with iTunes Library via VPN

  - by sudo work

  Alright, so I'm currently behind a network router (not under my control). The router performs NAT and somehow prevents a computer from scanning other nodes. At least, you're unable, in this instance, to locate an iTunes library. You can, however, communicate with a node's open ports if the local IP address is known, as well as the port. I haven't actually tried port scanning a specific IP using nmap or another tool yet. So I've tried one solution to remove the contribution of the router entirely (to verify that it works without the influence of the routers). I set up an access point using my iPhone and tethered my computer (with the library) to it. From here, I was able to pair my library and the iPhone Remote application. Control of the library was normal as well. This solution is not ideal, however, because I am actively using bandwidth with my computer and cannot afford to be tethered to my 3G connection. A viable solution for me is to use a common VPN connection, which I have set up on a Ubuntu (Intrepid) server that is remote. Both my computer and iPhone are able to access the VPN via PPTP. The server is setup with PPTPD as the VPN-server; I'm using IPTables to perform IP masquerading and forwarding traffic. I however, still cannot connect the library to the phone. I can however, see both devices on the VPN subnet (192.168.0.0/24). SSH'ing and such works fine. What settings on the VPN server must I change to get this to work? Also, how can I assign static IP addresses to various PPTP clients based on MAC addresses?

  Read the article

• remote telnet and email

  - by Mustafa Ismail Mustafa

  This issue has been occupying my work for the last few days and I will be understating when I say its driven me up the blasted walls. Essentially, I can ping and tracert the domain jnrcs.org and the subdomains mail.jnrcs.org and mail.jordanredcrescent.org. All three mentioned point to ip address 212.38.147.97. About 4 days ago, when we registered the domain "jnrcs.org" suddenly all external connection to the mail server from outside was lost. Not just mail, but other http based port-forwarded or natted services (such as camera surveillance and pbx services). I tried good old telnet (I'm a linux user) and I get the following output: telnet> o mail.jnrcs.org 25 Trying 212.38.147.97... telnet: Unable to connect to remote host: No route to host telnet> Tracert gives me: traceroute to mail.jnrcs.org (212.38.147.97), 30 hops max, 60 byte packets 1 192.168.1.2 (192.168.1.2) 0.869 ms 0.944 ms * 2 * * * 3 * * * 4 * * * 5 * * * 6 * 212.38.128.118 (212.38.128.118) 33.875 ms 39.187 ms 7 * * * 8 * * * 9 * * * 10 * * * 11 * * 212.38.147.97 (212.38.147.97) 67.621 ms I am stumped. Other friends from all around the world can telnet no problem. What could have possibly happened to make telnet/smtp/pop/imap/http access stop? Please bear in mind I'm primarily a developer but I [am under the delusion] that I can carry my weight in IT administration :) TIA

  Read the article

• Acer Laptop does not power up after repairing DC power jack

  - by Misbah Mashkoor

  I have an Acer travelmate laptop which (by mistake) I dropped on the floor with the power jack side down, with the charger connected and it broke the DC jack from the inside of the laptop. Then I unscrewed the laptop and soldered the DC jack back and then plugged it in and switched on the laptop without the batteries. It did switch on, that was before screwing everything back. Then after assembling the whole thing back it does not power up. So I disassembled it again and just took the part which contained the DC jack (My laptop is like in two parts one contains the power jack which then sits on some pins on the main PCB) to a technician and he said that if you had connected this to a motherboard then it would have burnt cause the soldering was not right. And then I checked with my laptop again by connecting everything the light (the charging light) comes on when I connect the power but it does not switch on. Right now nothing is connected to the laptop; no HD, CD ROM, RAM , Battery. Nothing! Even then it does not power up. Any suggestions?

  Read the article

• Cisco "copy startup-config tftp" results in a 0 byte file on the server?

  - by Geoffrey

  I'm pulling my hair out figuring this out. My startup-config is good, I can view it with a show command. I'm trying to copy it to a tftp server: asa5505# copy startup-config tftp Address or name of remote host []? ipaddress Destination filename [startup-config]? t !! %Error writing tftp://ipaddress/t (Timed out attempting to connect) On my TFTP server (SolarWinds), I get the following: binary, PUT. Started file name: C:\TFTP-Root\t binary, PUT. File Exists, C:\TFTP-Root\t binary, PUT. Deleting Existing File. binary, PUT. Interrupted by client, cause: The process cannot access the file 'C:\TFTP-Root\t' because it is being used by another process I've used tftpd32 with same results. I've tried different servers, even one on the same network as the asa ... same results. It'll create a 0 byte file and never do the dump. What's going on? Everything is working normally except for this.

  Read the article

• PXE bootable image for terminal server?

  - by HeavenCore

  We have 300 windows xp machines on cruddy old hardware across the company. With extended support for XP ending April next year we're looking into our options. Couple of options: Replace the 300 PC's with full windows 7 PC's (£100k +?) - no use of terminal server (our current model) Replace the 300 PC's with off the shelf thin clients & make use of our terminal server - Cheaper clients but Terminal Server CALS required? Keep the 300 PC's, replace windows XP with linux thin client capable of connecting to our terminal server - no hardware costs, just Terminal Server CALS required? Keep the 300 PC's - remove hard drives and make use of a PXE bootable "thin client" to connect to our terminal server If we were to choose option 4, what our the options out there? Is there any official PXE bootable thin clients for terminal server out there? If so, what are the licence requirements? Is there options we haven’t considered? There must be lots of companies out there in this situation - curious what the current trend is for this problem? Edit: Option 5 - Create a bootable Windows PE image with RDP auto start and use that as a "thin client" for our terminal server - is Windows PE licence free in such a model?

  Read the article

• Lightweight Linux distro that includes developer tools? (or, the most BSD-like Linux)

  - by RevAaron

  I cut my teeth on Minix and Slackware 1.1, but I've been in the OS X Wilderness for the last few years. I'm trying to standardize on a Linux distribution for personal and work-related use on less powerful laptops and under virtualization. So far, NetBSD and OpenBSD are the best fit for my purposes- but after plenty of frustration I've come to the conclusion that I need to stick with Linux to get the hardware and software support that comes with it. What I like about NetBSD/OpenBSD that I'd like to keep: X, but no default KDE, GNOME or XFCE! A sensible /etc and dot file setup- startx calls xinit, xinit looks for ~/.xinitrc; nothing more complicated than that is needed. Command line tools and file-based configuration: I shouldn't need a GUI to connect to a WAP. Decent selection of binary packages; building from source is OK, but nothing source-only like Gentoo. pkg_add (BSD) and apt-get both have treated me well in the past. Modest RAM and HDD requirements: boot + X + awesome+ two xterms takes up 80 MB on OpenBSD and 240 MB on Debian 5 and Crunchbang In my experience, most "lightweight" and Live CDs focus on a nice desktop environment crammed into a CD or USB stick; once you add build-essentials you end up with something just about as bloated as Ubuntu or Debian full install. Crunchbang is a great example. Thanks in advance for all suggestions!

  Read the article

• gpfs: adding a new nsd server to a cluster

  - by alessandra

  I have a gpfs cluster composed by 10 linux nodes, managed by a primary server A, which also act as nsd server for a first stack of disks. I attached a new jbod to one of the nodes (call it node B), which I would like to become a nsd server for this new stack of disks, but still be included in the cluster so that the disks are available to all the nodes. Node B is connected to the cluster via ethernet. How can I make the new nsd seen by all the nodes of the cluster? I can create the new nsd but when trying to create the filesystem on node B it the command mmcrfs times out. It looks like the nodes of the cluster cannot understand the filesystem location even if I specify them attached to server B in the description file. Would it be better to remove node B from the cluster, create a cluster on its own with its attached filesystem and connect it remotely with the previous cluster? Or a clustered NFS solution would apply better? Can you please give me any suggestion?

  Read the article

• VPN Error 619: Behind Cisco Router WRT310N

  - by ty91011

  I've researched a lot on all the forums and this error is too generic for any of the proposed solutions to work. I'll try to give as much detail and tried solutions. I'm running a CentOS PPTP server behind a Cisco WRT310N Router. Multiple clients from outside with different OS have failed with the same error 619, along with turning off windows firewall and disabling antivirus. I believe this is a router and IP routing issue, and not a client issue. When I connect from a client on the same router as the VPN server, it works when I use the 192. network address- but doesn't work with the public IP address. I've tried telnet to port 1723 from an outside server and I get in. I've opened up the VPN port (1723) on the router, VPN udp port (500), and the GRE port (47) to route to the VPN server's ip. Also, the server's router is behind a DSL modem. I had a glimmer of hope when this site: http://www.chicagotech.net/casestudy/vpnerror619.htm suggested that the PPoE authentication should reside on the router and not the modem. But I still came up empty. So does anybody know what the problem is?

  Read the article

• Basic IP address structure

  - by dannymcc

  We currently have a few servers, around 30-40 workstations and 16 phones. Each device has a static IP address. As an example the standard settings for a new workstation is; IP: 192.168.1.XXX Subnet: 255.255.255.0 Gateway: 192.168.1.99 DNS: 192.168.1.50 As I am slowly exploring new server OS's and virtualisation etc. I am getting close to wanting a wider range of IP addresses. What I would like to do is seperate the devices by IP as follows: Servers 192.168.1.XXX Workstations 192.168.2.XXX Printers 192.168.3.XXX Phones 192.168.4.XXX VM's 192.168.5.XXX Is this a bad idea, or is this a common way of doing things? My biggest concern is the phones and subnet masks. The phones are managed by our provider although I have access to the server that runs them. Would I need to change the subnet mask to 255.255.0.0 on all devices? Or only those that change? For example, the phones don't need to connect to any other devices other than other phones and the phone server. So if I have the phones on 192.168.1.XXX with a subnet mask of 255.255.255.0 and then moved everything I had complete ownership/control of to 192.168.X.XXX with a new subnet mask of 255.255.0.0. Would that work?

  Read the article

• Sticky connection and HTTPS support for HAProxy

  - by Saif

  We have 2 HTTP Load balancer with HAproxy and heartbeat. There are 4 apache nodes in this cluster. It's doing round robin load balancing. The HTTP cluster working fine. We are having problem with our portal because it uses SSO. We need sticky connection support in our HAproxy. Also we need load balancing for HTTPS traffic. Here's our HAproxy conf file. global # to have these messages end up in /var/log/haproxy.log you will # need to: # # 1) configure syslog to accept network log events. This is done # by adding the '-r' option to the SYSLOGD_OPTIONS in # /etc/sysconfig/syslog # # 2) configure local2 events to go to the /var/log/haproxy.log # file. A line like the following can be added to # /etc/sysconfig/syslog # # local2.* /var/log/haproxy.log # log 127.0.0.1 local0 log 127.0.0.1 local1 notice chroot /var/lib/haproxy pidfile /var/run/haproxy.pid maxconn 4000 user haproxy group haproxy daemon # turn on stats unix socket stats socket /var/lib/haproxy/stats #--------------------------------------------------------------------- # common defaults that all the 'listen' and 'backend' sections will # use if not designated in their block #--------------------------------------------------------------------- defaults mode http log global option httplog option dontlognull option http-server-close option forwardfor except 127.0.0.0/8 option redispatch retries 3 timeout http-request 10s timeout queue 1m timeout connect 10s timeout client 1m timeout server 1m timeout http-keep-alive 10s timeout check 10s maxconn 3000 #--------------------------------------------------------------------- # main frontend which proxys to the backends #--------------------------------------------------------------------- frontend main *:5000 acl url_static path_beg -i /static /images /javascript /stylesheets acl url_static path_end -i .jpg .gif .png .css .js use_backend static if url_static default_backend app #--------------------------------------------------------------------- # static backend for serving up images, stylesheets and such #--------------------------------------------------------------------- backend static balance roundrobin server static 127.0.0.1:4331 check #--------------------------------------------------------------------- # round robin balancing between the various backends #--------------------------------------------------------------------- backend app listen ha-http 10.190.1.28:80 mode http stats enable stats auth admin:xxxxxx balance roundrobin cookie JSESSIONID prefix option httpclose option forwardfor option httpchk HEAD /haproxy.txt HTTP/1.0 server apache1 portal-04:80 cookie A check server apache2 im-01:80 cookie B check server apache3 im-02:80 cookie B check server apache4 im-03:80 cookie B check Please advice. Thanks for your help in advance.

  Read the article

• How can I add a wireless router to a wired router?

  - by Tester101

  The Setup: wired D-link (EBR-2310) router connected to my cable modem. Wireless NetGear N300 (WNR2000v3) router connected to a LAN port on the wired router. What I'm trying to do: I'm trying to setup the wireless router to be a separate network, that only accesses the internet through the wired router. What I've done so far. I setup the wireless router's WAN port to get an address from ISP (which should be coming from my wired router running DHCP), and the LAN as a subnet (192.168.1). Wired router's LAN is 192.168.0. The problem: I'm not able to connect to the internet from the wireless router. At one point my wired router showed that it was handing out an IP to the wireless router, but that is not happening anymore. The question: Is what I'm trying to do possible? Am I not thinking about this properly? Do I need to buy a better wired router, with 2 WAN ports? How can I configure these routers to work together?

  Read the article

• What's the right way to create a Ubuntu user whose home directory is /var/www/SITE?

  - by Leonnears

  First of, I need to state I'm a complete ignorant when it comes to server administration on Ubuntu, and I'm doing what I can. I have been trying to do this for hours with no luck. Basically, I want to create a Ubuntu user whose home directory is /var/www/SITE, and prefered it is chroot'd to it. The chroot part is not so important right now, as first I prefer to make anything work. The user should be able to upload files here and the webserver (www-data user?) should be able to pick them up with no problem. I was able to create the user and give it the home directory /var/www/SITE. (the user is "anders"). I gave him a password, and "anders" can connect to FTP just fine and upload files. But here's where things don't work: While my user can upload files to that /var/www/SITE directory, when I access the webpage on my browser I get a Forbidden error. Note that anders is also a member of the www-data group. I can fix this by running sudo chmod g+s /var/www/SITE/* anders -R but this is of course not ideal. Ideally the files should "work" as soon as I upload them. What's the right way to fix this? If it matters (don't think so), I'm editing my files in Coda 2 and anders is the user for it.

  Read the article

• Can I attach a VPN firewall to an existing network and have it manage VPN connections?

  - by jules

  I'm quite new to networking and am trying to set up my first VPN connection. The Situation: I have been contracted for some programming at a facility some distance from my location. I would like to be able to set up a simple VPN connection to their network so that I may make adjustments without significant travel. Their Current Network: Six devices (one I need to connect to) plugged into a basic router (Dlink). This router has an internet connection and a static ip address. My Hopeful (questionable) Proposal: I attach a VPN Firewall I happen to own (Netgear FVS318) as device number seven on the client network. I disable routing / DHCP in the Netgear. I forward the appropriate IPSec ports from the Dlink to the Netgear. I then create a VPN connection on my office Windows 7 machine to the remote network. The request is forwarded from the Dlink to the Netgear where the VPN connection is authenticated. I now have a remote-access connection from my office PC to the client's local network. The Question: Will this proposal work? If not, would another possibility be to attach a computer with a VPN server to the client network? Also, as a note: the client has requested I not replace their router or place mine in-between theirs and the internet :( Thanks very much!

  Read the article

• Wifi network undetectable on a Lenovo G470

  - by Rex

  I have a WPA2 secured network with a visible SSID at home that works perfectly fine with a Dell laptop,a HP netbook and sundry mobile phones. When I try connecting my sister's Lenovo G470, it refuses to detect the wifi network no matter what, but shows up the neighbors' networks. The Lenovo also works correctly at her office. Both laptops run Windows 7. Already tried/checked the following: Manually configure wifi network settings (copied over from the Dell) Ensure there is no MAC address filtering on the router. Ensure router DHCP server is not running out of addresses to assign (I have set it to allocate upto 10). Reboot laptop, router etc. Is this a known problem, and is there anything else one could try? Update - The problematic Lenovo uses Windows 7 Home Basic while the Dell that works uses Home Premium and the HP netbook uses Starter edition - if that makes any difference. Further update - It is able to connect if I reboot into safe mode with networking. However in 'normal' mode it shows up the network sporadically, and then says there was an error connecting to it. All the network parameters, password, encryption, etc etc are EXACTLY the same as they are on the Dell.

  Read the article

• SSH hangs without password prompt

  - by Wilco

  Just reinstalled OS X and for some reason I now cannot connect to a specific machine on my local network via SSH. I can SSH to other machines on the network without any problems, and other machines can SSH to the problematic one as well. I'm not sure where to start looking for problems - can anyone point me in the right direction? Here's a dump of a connection attempt: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 10.0.1.7 [10.0.1.7] port 22. debug1: Connection established. debug1: identity file /Users/nwilliams/.ssh/identity type -1 debug1: identity file /Users/nwilliams/.ssh/id_rsa type -1 debug1: identity file /Users/nwilliams/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.5 debug1: match: OpenSSH_4.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '10.0.1.7' is known and matches the RSA host key. debug1: Found key in /Users/nwilliams/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password,keyboard-interactive debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic ... at this point it hangs for quite a while, and then resumes ... debug1: Unspecified GSS failure. Minor code may provide more information Server not found in Kerberos database debug1: Unspecified GSS failure. Minor code may provide more information Server not found in Kerberos database debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Trying private key: /Users/nwilliams/.ssh/identity debug1: Trying private key: /Users/nwilliams/.ssh/id_rsa debug1: Trying private key: /Users/nwilliams/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive

  Read the article

• laptop motherboard "shorts" when connected to adapter

  - by Bash

  Disclaimer: I'm sort of a noob, and this is a long post. Thank you all in advance! summary: completely dead laptop with no signs of life whatsoever (suddenly, for no apparent reason) Here's the deal: Lenovo Y470 (only a few months old with no water or shock damage). It stopped working suddenly (no lights, no sound, even when connecting adapter with or without battery). I tried a different adapter (same electrical rating), but no luck. I disassembled the thing completely, and tried plugging in the adapter and looking for signs of life with all different combinations of components installed (tried all combinations of RAM, CPU, USB power cords, screen, etc plugged in). no luck. Then, I noticed (as I was plugging in the adapter to try for the millionth time) that there was a "spark" for an instant when I first connect the adapter to the power jack. The adapter's LED would then flash (indicating it isn't working or charging). So, I thought the power jack has a short of some sort (due to bad soldering or something). Scanned virtually every single component on the motherboard, and tested the power jack connections with a multimeter. No shorts or damage to anything on the entire motherboard. Now I'm thinking I need to replace the motherboard. But, my actual question: What does this "shorting" when connecting the adapter signify? (btw, the voltage across the power connections and current through it drop to virtually zero when the adapter is connected and "sparks", and they stay that way). The bewildering thing is that there are no damaged components, and the voltage across adapter terminals returns to normal after I disconnect it (so it's not damaged). Please take a look at the pictures (of the motherboard's power connection and nearby components) and see if I'm missing something completely obvious... Links to pictures and laptop and motherboard model: pictures on DropBox Motherboard model: LA-6881P Laptop model: Lenovo IdeaPad Y470

  Read the article

• How to increase wifi speed for laptops

  - by sagar

  Now, Let me explain the situation. I am having a query regarding Wi-Fi network. I am having PC & laptop. I requested my Wi-Fi providers that I want connection in my PC. So that - Wi-Fi provider set up an Antenna on my building Terrace - They joined a cable to pc & that Antenna. ( I think using RJ45 connector ) - The reason behind this - my does not have a built in Wi-Fi adapter. Now - almost laptops have built in Wi-Fi. Now - On terrace there is Wi-Fi with superb speed. But on my flat - Wi-fi comes with low speed. So, when ever I use internet on my pc - it has great speed - but my laptop works with low speed. The reason behind this - PC is catching wifi from terrace & laptop is catching the wifi from it's own place. Now, My question is something like this. Can we place an antenna or something like that & connect it to laptop for better wifi speed? ( I am not technical person - Please add comment for down vote - if any ) ( Please add comment for more explanation of my Problem ) Thanks in advance for sharing your knowledge. Sagar

  Read the article

• Apache Virtual host not recognized

  - by Bozho

  I've been using one server, then I reinstalled everything on another server, and the mod_jk stopped working. Here is the situation: apache 2.0 sitting "in front" mod_jk used to connect to the apache to tomcat tomcat 6.0.26 used to server the actual requests I followed this tutorial. The result is: accessing http://mysite.com opens the index.html in /var/www/ accessing http://mysite.com:8080/ works OK the logs at /var/logs/apache2 show everything is OK: [Mon Mar 29 22:01:53.310 2010] [28349:3075389184] [info] init_jk::mod_jk.c (2830): mod_jk/1.2.26 initialized [Mon Mar 29 22:01:53 2010] [warn] No JkShmFile defined in httpd.conf. Using default /var/log/apache2/jk-runtime-status [Mon Mar 29 22:01:53 2010] [notice] Apache/2.2.9 (Debian) mod_jk/1.2.26 configured -- resuming normal operations I compared the server.xml, jk.conf, sites-enabled/mysite from the new server to those from the old one and they are identical. The domain name is the same (I updated the DNS record today, and it has refreshed successfully) So the question is, what can go wrong? Is there another place where problems would be logged, if such occur? Update What I can be almost certain of is that the virtual host is not recognized. It is always forwarded to the default virtual host. So, how to make sure the virtual host is recognized and working?

  Read the article

< Previous Page | 470 471 472 473 474 475 476 477 478 479 480 481  | Next Page >