Search Results

Search found 34513 results on 1381 pages for 'end task'.

Page 476/1381 | < Previous Page | 472 473 474 475 476 477 478 479 480 481 482 483  | Next Page >

• Fix bad superblock on logical partition

  - by Chris

  I was following http://www.howtoforge.com/linux_resi...xt3_partitions and when i reboot and run: root@Microknoppix:/home/knoppix# fsck -n /dev/sda7 fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) fsck.ext2: Superblock invalid, trying backup blocks... fsck.ext2: Bad magic number in super-block while trying to open /dev/sda7 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> so i ran e2fsck with all the block numbers that you need (forget exactly what tool i used to find where the superblocks are hidden) no dice then i ran testdisk and had it look for the superblock, no results anyone have any ideas? fdisk -l for reference: root@Microknoppix:/home/knoppix# fdisk -l Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x97646c29 Device Boot Start End Blocks Id System /dev/sda1 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 38912 312046593 f W95 Ext'd (LBA) /dev/sda5 64 326 2104320 82 Linux swap / Solaris /dev/sda6 * 327 2938 20972544 83 Linux /dev/sda7 2938 38912 288968672+ 83 Linux To be honest it looks like I lost it... Next step if that happens is to dump the partition to an image file and hope i can find or write some software to parse through the data looking for known file headers, i think.

  Read the article

• GlusterFS as elastic file storage?

  - by Christopher Vanderlinden

  Is there any way to run GlusterFS in a replicated mode, but with the ability to dynamically scale the volume up and down? Say you have 3 servers all running glusterd. your Gluster volume would have to be setup with replica 3 gluster volume create test-volume replica 3 192.168.0.150:/test-volume 192.168.0.151:/test-volume 192.168.0.152:/test-volume You would then mount it as say \mnt\gfs_test What happens when I want to add 2 more servers to the storage pool and then also use them in this volume? Is there any easy way to expand the volume AND increase that replica count to 5? My end goal is to run this on EC2 instances, say 3 Apache front ends, with the webroot setup on the gluster volume mount. My concern is that if I ever need to spin up a server, I would want the server to not only be an additional Apache front end, but also another server in the gluster file system, adding to fault tolerance as well as possibly giving a slight boost in read speed. Maybe there are better options that would fit the bill here? Thanks.

  Read the article

• Small store infrastructure - where to begin?

  - by KevinM1

  It looks like my older brother is about to change jobs - from lawyer to shooting range proprietor - and since I'm the family 'computer guy' I have the task of coming up with and setting up the in-store equipment. Only problem, I don't know how to start or where to look. I'm a web programmer, not an IT specialist. To that end, I figured I should ask the pros. Users: 3 (myself, my brother, and his business partner) Equipment: 1 Windows (likely 7) desktop for POS software, 1 Windows desktop/laptop for backroom use (bookkeeping, etc.) Other: ?? I'm looking for a reliable and, well, idiot-proof way to handle backups. Neither my brother nor his business partner are tech savvy (A web browser, email, MS Word and Excel are about the extent of their knowledge), so I need something they can handle. On-site would be preferable to off-site, given my brother's hesitance to have sensitive business data be handled by an outside source. I'm also looking for a small on-site server. I estimate that, at most, only 2-3 users will need access. A linux solution would keep costs down, but I'm concerned about Windows <- linux interoperability. Would the store security cameras' storage be handled by the security company, or would we have to stream that data to our own server? I know from my own experience with personal security that the company gives/loans a recording device to the home owner, but I'm not sure about business security. I know this sounds like a shopping list, and it's pretty vague. I wish I could give more detail, but between my own ignorance and things not being 100% nailed down on the business end, I'm a bit stuck. At the very least I'd like a nudge - links on a place to start, what to look for, things I need to think about, etc. - for this endeavor. Thanks.

  Read the article

• QMail do not delivery to remote mailboxes for my own domain

  - by lorenzo-s

  Sorry for the title, I don't know how to sum up this situation. I have a web server at mydomain.com, running qmail for website related mail delivery (i.e. newsletter, sign up confirmation, etc). qmail here is used only to send mails, because I have a fully working Google App Gmail associated with mydomain.com for normal email receiving. qmail runs fine when sending email to remote addresses, for example to [email protected], but fails when sending to [email protected]. I think it's because the server thinks that he have to manage mailboxes for mydomain.com locally, instead of redirect them to Gmail. Here is the /var/log/qmail/current for two email: the first one is sent without problems to example.com, second one fails because it's for mydomain.com: 2012-11-15 15:04:11.551933500 new msg 262580 2012-11-15 15:04:11.551936500 info msg 262580: bytes 5604 from <[email protected]> qp 5185 uid 33 2012-11-15 15:04:11.575910500 starting delivery 316: msg 262580 to remote [email protected] 2012-11-15 15:04:11.575912500 status: local 0/10 remote 1/20 2012-11-15 15:04:12.189828500 delivery 316: success: 74.125.136.27_accepted_message./Remote_host_said:_250_2.0.0_OK_1352991894_j49si13055539eep.9/ 2012-11-15 15:04:12.189830500 status: local 0/10 remote 0/20 2012-11-15 15:04:12.189831500 end msg 262580 2012-11-15 16:49:20.270332500 new msg 262580 2012-11-15 16:49:20.270336500 info msg 262580: bytes 2192 from <[email protected]> qp 5479 uid 33 2012-11-15 16:49:20.315125500 starting delivery 323: msg 262580 to local [email protected] 2012-11-15 16:49:20.315128500 status: local 1/10 remote 0/20 2012-11-15 16:49:20.320855500 delivery 323: failure: Sorry,_no_mailbox_here_by_that_name._(#5.1.1)/ 2012-11-15 16:49:20.320858500 status: local 0/10 remote 0/20 2012-11-15 16:49:20.372911500 bounce msg 262580 qp 5484 2012-11-15 16:49:20.372914500 end msg 262580 As you can see, it says: Sorry,_no_mailbox_here_by_that_name I can't say he's wrong :) How to solve this? How to let Google App Gmail manage incoming email for mydomain.com for messages sent by mydomain.com qmail server?

  Read the article

• How to get Synergy working on Ubuntu 11.10 and Windows 7?

  - by Linda

  I'm using Ubuntu 11.10 32-bit and Windows 7 64-bit, however, Synergy only works when a window (application or folder) is open and touching the edge of the screen where the mouse should "jump". In other words, if a window is open and maximized, Synergy works normally. Without any windows, the mouse does not jump to the other screen. My steps: (Ubuntu) apt-get install -y quicksynergy (Windows) Install Synergy (I've tried both 1.3.8 and 1.4.8 and both 32 and 64-bit) On Ubuntu 11.10 32-bit (Synergy Server config): ~/.quicksynergy/synergy.conf section: screens myubuntu: mywin7: end section: links myubuntu: right = mywin7 mywin7: left = myubuntu end On Ubuntu 11.10 32-bit: $ /usr/bin/synergys -f --config .quicksynergy/synergy.conf ... 2012-04-25T14:04:12 NOTE: client "mywin7" has connected /build/buildd/synergy-1.3.6/lib/server/CServer.cpp,287 (output hangs here) On Windows 7 64-bit: Synergy 1.3.8 Client on Microsoft Windows 7 x86 (WOW64) started client connecting to 'myubuntu': ###.###.###.###:24800 connected to server (output hangs here) At this point, things should work, but my mouse still can't change screens unless a window is maximized on my Ubuntu machine. Everything is running on port 24800. No firewall on Ubuntu. Firewall port 24800 open on Windows 7. This was previously working on Ubuntu 10.10 and Windows 7 (so only Ubuntu has been upgraded). I'm open to using either 32 or 64-bit on either server or client side, but I just want to get it working on Ubuntu 11.10 and Windows 7! I'm also using Ubuntu Classic (no effects), and not Unity.

  Read the article

• Port Forwarding to put my web server on The Internet

  - by Chadworthington

  I went to http://canyouseeme.org/ to check to see what my external IP address. Regardless of what port I enter, it tells me that the port is blocked. I have a LinkSys router that basically has the default settings with the exception that I have WEP encrptin setup and I have forwarded a few ports, including 80 and 69. I forwarded them to the 192.x.x.103 IP address of the PC which is running IIS. That PC runs Symantec Endpoint Protection, which I right mouse clicked in the tray to Disable. These steps used to make my PC visible so I could host my own web site in IIS on port 80, or some other port, like 69. Yet, the Open Port tool cannot see my IP when it checks eiether port and when I navigate to http://my external ip/ I get "page cant be displayed" At first I was thinking that maybe Comcast is blocking port 80, but 69 doesnt work eiether. I do not see any other blockking set up in my router and, as I mentioned, I went with teh defaults except where discussed. This is a corporate PC and Symantec End Point Protecion is new to it (this previously worked on teh same PC with Symantec Protection Agent), but I thought that disabling Sym End Pt from the tray, that that would effectively neutralize it. I do not have the rights to kill the program itself. Any suggestions on what else to try to make my PC externally visible?

  Read the article

• Google bots are severely affecting site performance

  - by Lynn

  I have an aggregate site on a linux server that pulls in feeds from a universe of about 2,000 blogs. It's in Wordpress 3.4.2 and I have a cron job that is staggered to run five times an hour on another server to pull in the stories and then publish them to the front page of this site. This is so I didn't put too much pressure all on one server. However, the Google bots, which visit a few times every hour bring the server to its knees in the morning and evenings when there is an increase in traffic on the site. The bots have something like 30,000 links to follow at this point. How do I throttle the bots to simply grab the new stories off the front page and stop there? EDIT- Details of my server configuration: The way we have this set up is the server that handles all the publishing is an unmanaged instance via AWS. It mounts the NFS server and connects to the RDS to update content, etc. You get to this publishing instance via a plugin that detects the wp-admin link and then redirects you into there. The front end app server also mounts the NFS and requests data from the RDS. It is the only one that has the WP Super Cache on it.... The OS is Ubuntu on the App server and the NFS runs CentOs. The front end is Nginx and the publishing server is Apache.

  Read the article

• How to send from my Z88 to my PC

  - by Bevan

  I've got a Cambridge Z88 that I want to get working with my PC. Around 6 years ago - in 2004 - I made heavy use of my Z88 to do a whole bunch of writing on the train while commuting to and from work. The Z88 is solid state, lightweight and has a full size silent keyboard, so it works very well as a writing instrument. I still have the serial cable I soldered up back then and used successfully in 2004. It has these connections: Z88 9 pin ----- ------- 2 TxD ------> RxD 2 3 RxD <------ TxD 3 7 GND <-----> GND 5 4 RTS ------> CTS 8 5 CTS <-+ RTS 7 8 DCD <-+---- DTR 4 9 DTR ----+-> DCD 1 +-> DSR 6 Unfortunately, I haven't been able to find my notes from 2004 that describe how I got it to work back then. I've spent several hours trying to Google a result, but to no avail. I'm pretty sure the cable is fine - after all, it's what I used successfully six years ago, and I've checked it out with a multimeter - so I'm focusing on the PC end of things, which is where I'd like some assistance. Q1: In my recent attempts, I've been using both Hyperterminal (as built into Windows XP) and the command line (copy com2: con:), but with no success. What's a good (better!) serial communications application to use? Is there one that allows me to see as deep as the signalling that's occurring on the wire? Q2: If you have a Z88 that works correctly with your PC, what software do you use on the PC end, and what's the pinout of your cable? I'm pretty sure that the Z88 itself is working properly: When using the built in Import/Export tool to send a file, I see different behaviour when my serial cable is connected compared to disconnected. When disconnected, the transmission appears to work, with a progress meter counting up and then finishing; when connected, nothing happens 'cept a timeout if I wait long enough.

  Read the article

• Outlook 2010 not resolving SMTP address to Display Name

  - by Ben

  I have a weird problem where a user (director, naturally) has an odd problem with the way the to field shows in his Outlook. We are using Outlook 2010 (with RPC/HTTP) and Exch 2003 at the back end. Most of his mail shows in his mailbox with the To: field as normal. (e.g. Fred Bloggs in the to field.) However, some mails come in showing in the To: field as [email protected]. (Apparently this is an issue!) For example, most show as: but a few come in as: There doesn't appear to be a pattern to this. I have tried to replicate by: Sending from any specific senders to see if it recurs (it doesn't) Typing his full name in my Outlook and sending (it resolves as normal) Sending programatically (e.g. from script) - (it still resolves OK) Forcing a "[email protected]" entry in my Outlook. It resolves as soon as I hit enter Sending in cached mode Sending disconnected Anyone got any ideas how I can either replicate the problem or fix it! I can't tell at the moment whether it is a problem at his end or the sender's. EDIT This seems to be a global issue, following some more digging. Most people seem to have a few emails in their inbox addressed to their smtp address, rather than display name.

  Read the article

• Issues with Apache redirect to www-prefixed URL

  - by lamp_scaler

  I have a website with domain mysite.com. I would like to have it so that if a user types in "mysite.com" it will redirect to "www.mysite.com". Additionally, "mysite.com/subdir" will also redirect to "www.mysite.com/subdir". I've looked and made changes with vhosts and also rewrites, but it's not working for the "mysite.com/subdir"-"www.mysite.com/subdir" case. Every time I type in "mysite.com/subdir", it will redirect to "www.mysite.com". Only "www.mysite.com/subdir" works. Not sure how to troubleshoot this. I turned on rewrite logs and didn't see anything obvious, yet. This is my config files so far. Please let me know what I'm missing. Thanks! FYI: I'm using CentOS 5.4, nginx 1.2.0 on top of Apache 2.2.3. The site itself is built with CodeIgniter framework. http.conf: ServerTokens Prod ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive Off MaxKeepAliveRequests 100 KeepAliveTimeout 15 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 10 ServerLimit 256 MaxClients 60 MaxRequestsPerChild 10000 #StartServers 8 #MinSpareServers 5 #MaxSpareServers 20 #ServerLimit 256 #MaxClients 256 #MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> Listen 69 LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule alias_module modules/mod_alias.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_balancer_module modules/mod_proxy_balancer.so LoadModule proxy_ftp_module modules/mod_proxy_ftp.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule file_cache_module modules/mod_file_cache.so LoadModule mem_cache_module modules/mod_mem_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so #rpaf settings LoadModule rpaf_module modules/mod_rpaf-2.0.so RPAFenable On RPAFproxy_ips 127.0.0.1 RPAFsethostname On # The header where the real client IP address is stored. RPAFheader X-Forwarded-For Include conf.d/*.conf User apache Group apache ServerAdmin root@localhost ServerName www.mysite.com:80 UseCanonicalName Off DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory "/var/www/html"> Options Indexes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> <IfModule mod_userdir.c> UserDir disable </IfModule> DirectoryIndex index.html index.html.var AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all </Files> <DirectoryMatch "^/.*/\.svn/"> Order deny,allow Deny from all </DirectoryMatch> TypesConfig /etc/mime.types DefaultType text/plain <IfModule mod_mime_magic.c> MIMEMagicFile conf/magic </IfModule> HostnameLookups Off ErrorLog logs/error_log LogLevel warn LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent CustomLog logs/access_log combined ServerSignature Off Alias /icons/ "/var/www/icons/" <Directory "/var/www/icons"> Options Indexes MultiViews AllowOverride None Order allow,deny Allow from all </Directory> <IfModule mod_dav_fs.c> DAVLockDB /var/lib/dav/lockdb </IfModule> ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" <Directory "/var/www/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> IndexOptions FancyIndexing VersionSort NameWidth=* HTMLTable AddIconByEncoding (CMP,/icons/compressed.gif) x-compress x-gzip AddIconByType (TXT,/icons/text.gif) text/* AddIconByType (IMG,/icons/image2.gif) image/* AddIconByType (SND,/icons/sound2.gif) audio/* AddIconByType (VID,/icons/movie.gif) video/* AddIcon /icons/binary.gif .bin .exe AddIcon /icons/binhex.gif .hqx AddIcon /icons/tar.gif .tar AddIcon /icons/world2.gif .wrl .wrl.gz .vrml .vrm .iv AddIcon /icons/compressed.gif .Z .z .tgz .gz .zip AddIcon /icons/a.gif .ps .ai .eps AddIcon /icons/layout.gif .html .shtml .htm .pdf AddIcon /icons/text.gif .txt AddIcon /icons/c.gif .c AddIcon /icons/p.gif .pl .py AddIcon /icons/f.gif .for AddIcon /icons/dvi.gif .dvi AddIcon /icons/uuencoded.gif .uu AddIcon /icons/script.gif .conf .sh .shar .csh .ksh .tcl AddIcon /icons/tex.gif .tex AddIcon /icons/bomb.gif core AddIcon /icons/back.gif .. AddIcon /icons/hand.right.gif README AddIcon /icons/folder.gif ^^DIRECTORY^^ AddIcon /icons/blank.gif ^^BLANKICON^^ DefaultIcon /icons/unknown.gif #AddDescription "GZIP compressed document" .gz #AddDescription "tar archive" .tar #AddDescription "GZIP compressed tar archive" .tgz ReadmeName README.html HeaderName HEADER.html IndexIgnore .??* *~ *# HEADER* README* RCS CVS *,v *,t AddLanguage ca .ca AddLanguage cs .cz .cs AddLanguage da .dk AddLanguage de .de AddLanguage el .el AddLanguage en .en AddLanguage eo .eo AddLanguage es .es AddLanguage et .et AddLanguage fr .fr AddLanguage he .he AddLanguage hr .hr AddLanguage it .it AddLanguage ja .ja AddLanguage ko .ko AddLanguage ltz .ltz AddLanguage nl .nl AddLanguage nn .nn AddLanguage no .no AddLanguage pl .po AddLanguage pt .pt AddLanguage pt-BR .pt-br AddLanguage ru .ru AddLanguage sv .sv AddLanguage zh-CN .zh-cn AddLanguage zh-TW .zh-tw LanguagePriority en zh-CN zh-TW ca cs da de el eo es et fr he hr it ja ko ltz nl nn no pl pt pt-BR ru sv ForceLanguagePriority Prefer Fallback AddDefaultCharset UTF-8 AddType text/x-component .htc AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddHandler type-map var AddType text/html .shtml AddOutputFilter INCLUDES .shtml Alias /error/ "/var/www/error/" <IfModule mod_negotiation.c> <IfModule mod_include.c> <Directory "/var/www/error"> AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en es de fr ForceLanguagePriority Prefer Fallback </Directory> </IfModule> </IfModule> BrowserMatch "Mozilla/2" nokeepalive BrowserMatch "MSIE 4\.0b2;" nokeepalive downgrade-1.0 force-response-1.0 BrowserMatch "RealPlayer 4\.0" force-response-1.0 BrowserMatch "Java/1\.0" force-response-1.0 BrowserMatch "JDK/1\.0" force-response-1.0 BrowserMatch "Microsoft Data Access Internet Publishing Provider" redirect-carefully BrowserMatch "MS FrontPage" redirect-carefully BrowserMatch "^WebDrive" redirect-carefully BrowserMatch "^WebDAVFS/1.[0123]" redirect-carefully BrowserMatch "^gnome-vfs/1.0" redirect-carefully BrowserMatch "^XML Spy" redirect-carefully BrowserMatch "^Dreamweaver-WebDAV-SCM1" redirect-carefully vhost.conf: NameVirtualHost *:69 <VirtualHost *:69> ServerName mysite.com ServerAlias vip.mysite.com Redirect / http://www.mysite.com/ </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/mysite/www ServerName www.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/mysite/www/assets ServerName static.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/admin/www ServerName admin.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/other/trunk/www ServerName othersite.com ServerAlias www.othersite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /var/www/html ServerName test.mysite.com ServerAlias test2.mysite.com </VirtualHost> /home/mysite/mysite/www/.htaccess: RewriteEngine on # In my case all CI files are outside this web root, so we can # allow any files or directories that exist to be displayed directly RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d # hide index.php RewriteRule .* index.php/$0 [L] # BEGIN Compress text files <ifModule mod_deflate.c> <filesMatch "\.(css|js|x?html?|php)$"> SetOutputFilter DEFLATE </filesMatch> </ifModule> # END Compress text files # BEGIN Expire headers <ifModule mod_expires.c> ExpiresActive On ExpiresDefault "access plus 1 seconds" ExpiresByType image/x-icon "access plus 2592000 seconds" ExpiresByType image/jpeg "access plus 2592000 seconds" ExpiresByType image/png "access plus 2592000 seconds" ExpiresByType image/gif "access plus 2592000 seconds" ExpiresByType application/x-shockwave-flash "access plus 2592000 seconds" ExpiresByType text/css "access plus 604800 seconds" ExpiresByType text/javascript "access plus 604800 seconds" ExpiresByType application/javascript "access plus 604800 seconds" ExpiresByType application/x-javascript "access plus 604800 seconds" ExpiresByType application/xhtml+xml "access plus 600 seconds" </ifModule> # END Expire headers # BEGIN Cache-Control Headers <ifModule mod_headers.c> <filesMatch "\.(ico|jpe?g|png|gif|swf)$"> Header set Cache-Control "max-age=2592000, public" </filesMatch> <filesMatch "\.(css)$"> Header set Cache-Control "max-age=604800, public" </filesMatch> <filesMatch "\.(js)$"> Header set Cache-Control "max-age=604800, private" </filesMatch> </ifModule> # END Cache-Control Headers # BEGIN Turn ETags Off <ifModule mod_headers.c> Header unset ETag </ifModule> FileETag None # END Turn ETags Off /etc/nginx/conf.d/default.conf: server { listen 80; server_name static.mysite.com; location / { root /home/mysite/mysite/www/assets; index index.html index.htm; expires max; } } server { listen 80; server_name *.mysite.com www.mysite.com vip.mysite.com; #Set this larger if uploading big files client_max_body_size 5m; location / { proxy_pass http://127.0.0.1:69; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; #client_max_body_size 10m; client_body_buffer_size 128k; proxy_buffer_size 4k; proxy_buffers 4 32k; } }

  Read the article

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• Outlook locking network connection/session?

  - by HaydnWVN

  Scenario: We have an 'automatic orders' machine sat in the corner running XP with Outlook 2003. Its job is to check for new emails on a specific account, when it encounters one it checks the e-mail body for specific wording to determine which customer it is from (using a macro), then it checks the attachment for specific order codes before parsing the attachment to create a .csv file (which is then e-mailed onto one of the sales team) before importing the .csv into our bespoke ERP/Sales Order system to create an order. Problem: Periodically the machine will have symptoms of a lost network connection (unable to connect to any network source). Sometimes after several days, sometimes over a week. Volume of emails/orders processed does not seem to be linked. Additional info: The machines .pst is stored on a mapped network location. The .csv created is stored on a mapped network location. This is a workgroup, not a domain. All network drives are Samba shares from an Ubuntu fileserver. Our bespoke system runs from a database (MySQL) Ubuntu server. Our troubleshooting so far: I have switched machines (previous was Win2000) with the same symptoms. Restarting the machine FIXES the problem. Closing Outlook and then end tasking an Outlook.exe background process FIXES the problem. If you close Outlook, without end taking the background process, outlook will not reopen (saying it cannot find the pst file & it will not open any network location). Does Outlook have some kind of 'max session' linking it to network activity that is not closing after a mail request? Could Auto-archive be causing this? Is there a tool to check/display what each outlook.exe process is doing? Have not found many ways to troubleshoot this yet, as it is so infrequent...

  Read the article

• "could not find suitable fingerprints matched to available hardware" error

  - by Alex

  I have a thinkpad t61 with a UPEK fingerprint reader. I'm running ubuntu 9.10, with fprint installed. Everything works fine (I am able to swipe my fingerprint to authenticate any permission dialogues or "sudo" prompts successfully) except for actually logging onto my laptop when I boot up or end my session. I receive an error below the gnome login that says "Could not locate any suitable fingerprints matched to available hardware." What is causing this? here are the contents of /etc/pam.d/common-auth file # # /etc/pam.d/common-auth - authentication settings common to all services # # This file is included from other service-specific PAM config files, # and should contain a list of the authentication modules that define # the central authentication scheme for use on the system # (e.g., /etc/shadow, LDAP, Kerberos, etc.). The default is to use the # traditional Unix authentication mechanisms. # # As of pam 1.0.1-6, this file is managed by pam-auth-update by default. # To take advantage of this, it is recommended that you configure any # local modules either before or after the default block, and use # pam-auth-update to manage selection of other modules. See # pam-auth-update(8) for details. # here are the per-package modules (the "Primary" block) auth sufficient pam_fprint.so auth [success=1 default=ignore] pam_unix.so nullok_secure # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_ecryptfs.so unwrap # end of pam-auth-update config #auth sufficient pam_fprint.so #auth required pam_unix.so nullok_secure

  Read the article

• Shell wrong encoding

  - by csch

  Somehow I managed to screw up my shell-encoding. An example: root§server:ç£ cat --help Usage: cat ¡OPTION¿... ¡FILE¿... Concatenate FILE(s), or standard input, to standard output. -A, --show-all equivalent to -vET -b, --number-nonblank number nonempty output lines -e equivalent to -vE -E, --show-ends display $ at end of each line -n, --number number all output lines -s, --squeeze-blank suppress repeated empty output lines -t equivalent to -vT -T, --show-tabs display TAB characters as ^I -u (ignored) -v, --show-nonprinting use ^ and M- notation, except for LFD and TAB --help display this help and exit --version output version information and exit With no FILE, or when FILE is -, read standard input. Examples: cat f - g Output f's contents, then standard input, then g's contents. cat Copy standard input to standard output. Report cat bugs to bug-coreutils§gnu.org GNU coreutils home page: <http://www.gnu.org/software/coreutils/> General help using GNU software: <http://www.gnu.org/gethelp/> For complete documentation, run: info coreutils 'cat invocation' root§server:ç£ It should look like: root@server:~# cat --help Usage: cat [OPTION]... [FILE]... Concatenate FILE(s), or standard input, to standard output. -A, --show-all equivalent to -vET -b, --number-nonblank number nonempty output lines -e equivalent to -vE -E, --show-ends display $ at end of each line -n, --number number all output lines -s, --squeeze-blank suppress repeated empty output lines -t equivalent to -vT -T, --show-tabs display TAB characters as ^I -u (ignored) -v, --show-nonprinting use ^ and M- notation, except for LFD and TAB --help display this help and exit --version output version information and exit With no FILE, or when FILE is -, read standard input. Examples: cat f - g Output f's contents, then standard input, then g's contents. cat Copy standard input to standard output. Report cat bugs to [email protected] GNU coreutils home page: <http://www.gnu.org/software/coreutils/> General help using GNU software: <http://www.gnu.org/gethelp/> For complete documentation, run: info coreutils 'cat invocation' root@server:~# I have no clue what went wrong, do you have any ideas?

  Read the article

• How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment [closed]

  - by lmttag

  Possible Duplicate: How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment We have an ASP.NET Web API server that serves up a SQL Server data driven website. The API uses JSON to transfer data from SQL Server to the front end. We need to move it to an internal production environment (nothing will be exposed on the public Internet) and we’re having problems - or just not understanding what needs to be done. There are two domains: The corporate domain - where all users login normally. The process domain - contains the database the Web API needs to access. The IT staff wants to put a DMZ between the two domains to house the IIS app and shield the users on the corporate domain from having access into the process domain directly. The ideal configuration is: corp domain (end users) <–> firewall (open port 80) <–> DMZ (web server running IIS) <–> firewall (open port 80 or 1433????) <–> process domain (IIS for Web API and SQL Server) We don’t really understand how to deploy our browser/Web API application in this scenario. Do we need to break up our application so that all the client code is on the IIS server in the DMZ, while the Web API gets installed on the server in the process domain? Does the entire app (client code and Web API) stay together on the IIS server in the DMZ, which then somehow accesses the SQL Server instance to get data? From the IIS server and app in the DMZ, would you simply access the Web API on the server in the process domain by going to http://server/appname/api/getitmes? In the second firewall between the DMZ and the process domain, would you have to open port 1433 or just port 80 since the Web API is a HTTP endpoint? Or, is there some better way of deployment (i.e., how ASP.NET Web API single page applications written all in HTML5 and JavaScript supposed to be deployed to production environments?)? NB: The servers are Win2k8 R2, SQL Server 2k8 R2, and IIS 7.5.

  Read the article

• What does "incoming" and "outgoing" traffic mean?

  - by mgibsonbr

  I've seen many resources explaining how to set up a server's firewall to allow incoming and outgoing traffic on HTTP standard ports (80 and 443), but I can't figure out why I would need either of them. Do I need to unblock both for a "regular" web site to work? For file uploads to work? Are there situations where it would be advisable to unblock one and leave the other blocked? Sorry if that's a basic question, but I couldn't find it explained anywhere (also I'm not a native english speaker). I know in a "regular" web site the client is always the one who initiates a request, so I'm assuming a web server must accept incoming traffic on those ports, and my common sense tells me the server is allowed to send a response without unblocking anything else (otherwise it wouldn't make sense to have two types of rules). Is that correct? But what is an outgoing web (service) traffic, and what would be its use? AFAIK if the server wanted to initiate a connection with another machine, the specific port that matters is the one in the other end (i.e. the destination port would be 80), on its end any free port could be used (the source port would be random). I can open HTTP requests from my server (using wget for instance) without unblocking anything. So I'm assuming my concepts of "incoming" and "outgoing" are wrong somehow.

  Read the article

• why does the partition start on sector 2048 instead of 63

  - by gcb

  I had two drives partitioned the same and running 2 raid partitions on each. One died and I replaced it under warranty for the same model. While trying to partition it, the first partition can only start on sector 2048, instead of 63 that was before. Driver have different geometry as previous and remaining ones. (Fewer heads/more cylinders) old drive: $ sudo fdisk -c -u -l /dev/sdb Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000aa189 Device Boot Start End Blocks Id System /dev/sdb1 * 63 174080339 87040138+ 83 Linux /dev/sdb2 174080340 182482334 4200997+ 82 Linux swap / Solaris /dev/sdb3 182482335 3907024064 1862270865 fd Linux raid autodetect remanufactured drive received from warranty: $ sudo fdisk -c -u -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 81 heads, 63 sectors/track, 765633 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d0b5d Device Boot Start End Blocks Id System /dev/sda1 2048 ... why is that?

  Read the article

• Salary Survey Entry Level network position [closed]

  - by will

  Hello, I started interning with a company about 5 months ago and for the past 7 months I have been a normal part time employee. This week I have a review, where I am hoping to get a raise. I started at $8 interning, and now I'm up to $13. What I am trying to figure out is how to survey what others are making in similar positions so I can take it to the review as a base number. here are my thoughts on my position right now. Review Thoughts My Qualifications: • Associates of applied Science - IT network Specialist • CompTIA A+ certification • CompTIA Server+ certification • CompTIA Network+ certification • Currently pursuing Cisco certifications • Junior status at Insert college Pursuing Bachelors in Information Technology with an emphasis in Networking. 3.4 GPA • 1 year of working at Insert Company. My contributions to Insert Company • Offering near fulltime through semester and fulltime through summer. • Ability to work after hours and on weekends • Developed and support helpdesk system • Set up and maintain Update server to keep desktop clients up to date • Deployed and maintain antivirus solution for end users • Assist with main projects such as SAN, Virtualization, and network survey. Any tips on determining an asking number would help. I was thinking $17-$18, am I way off here? • Migrating end user stations to Windows 7 (current project) • Developing imaging solution for Desktop PCs (current project)

  Read the article

• Intermittently uncommunicative subnets

  - by mhd

  Last week proved me a veritable Cassandra: I've always said that it's a bad idea to have only one firewall/router, without a backup or failover. And thus our Cisco PIX went haywire, refusing to route properly. And of course, the only one available here on short notice is me, and while I'm quite grounded in Linux, I'm really a developer not a sysadmin (the fact that this hit me on sysadmin appreciation day is a bit ironic). Anyway, this weekend I tried to hack up a temporary solution: I used an old server with enough NICs (two built-in, four on a card) to serve as a gateway and firewall. Due to some problems with the raid controller, I got only two router distros running, and between Untangle and Ebox I decided for the latter. Now everything is quite okay. I've got all the different subnets we've got here (all with separate switches) talking to each other and even to the internet (Cisco 2800 router, T1 lines). But from time to time (20-60 minute intervals), I get a total routing failure. Our main, office subnet can't talk to our server subnet and can't connect to the internet. This is not the end of a gradual slowdown, either everything's working perfectly or I get a total lack of communication for about two minutes each time. Now I'm a bit at wits end what to check. At least with the default EBox setup, nothing in /var/log shows anything weird and it doesn't exactly have lots of built-in monitoring tools. So I'm hoping someone here could give me some pointers about what to look out for. I did change the ethernet cable from the office switch to the firewall, with no results. I might change switches, although within the switch it seems to work ok enough. Edit: I'm not sure whether this is the sole cause of the problem, but after I noticed a few DHCP entries just before the last drop of connectivity, I tried to reproduce that. And alas, whenever I renew a DHCP connection, I can't access other subnets anymore. Running ISC DHCPD 3.0.6.

  Read the article

• Why am I not able to create a backup plan for TFS?

  - by noocyte

  I am trying to create a backup plan using the TFS Power Tools but I keep running into this error message: I have checked that the account has Full Control on the share, I can edit, create and delete files there. From the log: [Info @07:15:00.403] Starting creating backup test validation [Error @07:15:00.700] Microsoft.SqlServer.Management.Smo.FailedOperationException: Backup failed for Server 'WMSI003714N\SqlExpress'. ---> Microsoft.SqlServer.Management.Common.ExecutionFailureException: An exception occurred while executing a Transact-SQL statement or batch. ---> System.Data.SqlClient.SqlException: Cannot open backup device '\\wmsi003714n\sql dump\Tfs_Configuration_20100910091500.bak'. Operating system error 5(failed to retrieve text for this error. Reason: 1815). BACKUP DATABASE is terminating abnormally. at Microsoft.SqlServer.Management.Common.ConnectionManager.ExecuteTSql(ExecuteTSqlAction action, Object execObject, DataSet fillDataSet, Boolean catchException) at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand, ExecutionTypes executionType) --- End of inner exception stack trace --- at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand, ExecutionTypes executionType) at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(StringCollection sqlCommands, ExecutionTypes executionType) at Microsoft.SqlServer.Management.Smo.ExecutionManager.ExecuteNonQuery(StringCollection queries) at Microsoft.SqlServer.Management.Smo.BackupRestoreBase.ExecuteSql(Server server, StringCollection queries) at Microsoft.SqlServer.Management.Smo.Backup.SqlBackup(Server srv) --- End of inner exception stack trace --- at Microsoft.SqlServer.Management.Smo.Backup.SqlBackup(Server srv) at Microsoft.TeamFoundation.PowerTools.Admin.Helpers.BackupFactory.TestBackupCreation(String path) [Error @07:15:00.731] !Verify Error!: Account GROUPINFRA\SA-NO-TeamService failed to create backups using path \\wmsi003714n\sql dump [Info @07:15:00.731] "Verify: Grant Backup Plan Permissions\Root\VerifyDummyBackupCreation(VerifyTestBackupCreatedSuccessfully): Exiting Verification with state Completed and result Error" Any ideas?

  Read the article

• SMTP Client implementation [on hold]

  - by orif

  I'm implementing SMTP client. What should the client do once it already sent the "." at the end of the mail, but didn't receive "250 Ok"? This is how the conversation between the client and server look like: Server Response: 220 www.sample.com ESMTP Postfix Client Sending : HELO domain.com Server Response: 250 Hello domain.com Client Sending : MAIL FROM: <[email protected]> Server Response: 250 Ok Client Sending : RCPT TO: <[email protected]> Server Response: 250 Ok Client Sending : DATA Server Response: 354 End data with <CR><LF>.<CR><LF> Client Sending : Subject: Example Message Client Sending : From: [email protected] Client Sending : To: [email protected] Client Sending : Client Sending : TEST MAIL Client Sending : Client Sending : . Server Response: 250 Ok: queued as 23411 Client Sending : QUIT I'm not sure what should I do if the client sends "." and doesn't receive the 250 Ok - because of possible network error. Was the "." sent or not? Should the client resend the mail - and - maybe - duplicate the item, or not - and risk in losing an important mail item? Thank you.

  Read the article

• Windows 7 64-bit Google Chrome Makes Desktop Unresponsive

  - by Meengla

  For the past 1-2 weeks my desktop becomes unresponsive sometimes. The problem seems to happen as I load a page in Google Chrome; it could be any page though today it happened when I tried to load a page with Flash content in it. The problem is not consistent and there is no pattern. I can do a virus scan using some software (not antivirus installed--never needed that) but I strongly suspect it is some software I installed or some Windows Update. This is a very powerful Dell Optiplex 990 with 16GB RAM, so Memory shouldn't be an issue. When the problem happens the cursor becomes spinning even over the taskbar and control alt delete takes a long time. Eventually I get a message that 'this program is not responding' with end/close and 'cancel' icon. But repeated end or cancel does nothing. Then the menu for ctrl alt del comes up. The rest of the applications keep running fine though I can't get to them because the cursor is the wait-cursor. What is happening? How can I find what exactly caused the problem? Thanks.

  Read the article

• how can i move ext3 partition to the beginning of drive without losing data?

  - by Felipe Alvarez

  I have a 500GB external drive. It had two partitions, each around 250GB. I removed the first partition. I'd like to move the 2nd to the left, so it consumes 100% of the drive. How can this be accomplished without any GUI tools (CLI only)? fdisk Disk /dev/sdd: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc80b1f3d Device Boot Start End Blocks Id System /dev/sdd2 29374 60801 252445410 83 Linux parted Model: ST350032 0AS (scsi) Disk /dev/sdd: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 2 242GB 500GB 259GB primary ext3 type=83 dumpe2fs Filesystem volume name: extstar Last mounted on: <not available> Filesystem UUID: f0b1d2bc-08b8-4f6e-b1c6-c529024a777d Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal dir_index filetype needs_recovery sparse_super large_file Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 15808608 Block count: 63111168 Reserved block count: 0 Free blocks: 2449985 Free inodes: 15799302 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8208 Inode blocks per group: 513 Filesystem created: Mon Feb 15 08:07:01 2010 Last mount time: Fri May 21 19:31:30 2010 Last write time: Fri May 21 19:31:30 2010 Mount count: 5 Maximum mount count: 29 Last checked: Mon May 17 14:52:47 2010 Check interval: 15552000 (6 months) Next check after: Sat Nov 13 14:52:47 2010 Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: d0363517-c095-4f53-baa7-7428c02fbfc6 Journal backup: inode blocks Journal size: 128M

  Read the article

• What's wrong with my .htaccess? Trying to simplify actual code

  - by AlexV

  This is my actual .htaccess: #If the requested URI does not end with an extension RewriteCond %{REQUEST_URI} !\.(.*) #If the requested URI is not in an excluded location RewriteCond %{REQUEST_URI} !^/(excluded1|excluded2)/ #Then serve the URI via the mapper RewriteRule .* /seo-urls/seo-urls-mapper.php?uri=%{REQUEST_URI} [L,QSA] #If the requested URI ends with .php* RewriteCond %{REQUEST_URI} \.php.*$ [NC] #If the requested file is not seo-urls-mapper.php (avoid .htaccess loop) RewriteCond %{REQUEST_FILENAME} (?<!seo-urls-mapper)\.php.*$ #Then serve the URI via the mapper RewriteRule .* /seo-urls/seo-urls-mapper.php?uri=%{REQUEST_URI} [L,QSA] Since all conditions are compatibles except the 1st ones (no extension and *.php* match) all I should have to do is to add the [OR] condition to these 2 lines, but when I'm adding it it's not working (my no extension rule don't work anymore). This is my new (not working) code: #If the requested URI does not end with an extension OR if the URI ends with .php* RewriteCond %{REQUEST_URI} !\.(.*) [OR] RewriteCond %{REQUEST_URI} \.php.*$ [NC] #If the requested file is not seo-urls-mapper.php (avoid .htaccess loop) RewriteCond %{REQUEST_FILENAME} (?<!seo-urls-mapper)\.php.*$ #If the requested URI is not in an excluded location RewriteCond %{REQUEST_URI} !^/(excluded1|excluded2)/ #Then serve the URI via the mapper RewriteRule .* /seo-urls/seo-urls-mapper.php?uri=%{REQUEST_URI} [L,QSA] Hopefully someone will be able to clarify this issue... I guess I don't fully understand the use of [OR]. Thanks!

  Read the article

• OpenVPN-based VPN server on same system it's "protecting": feasible?

  - by Johnny Utahh

  Scenario: hosted machine (typically a VPS) serving wiki, svn, git, forums, email lists (eg: GNU mailman), Bugzilla (etc) privately to < 20 people. People not on team not allowed access. Seeking VPN-restricted access to said server. Have good user experience with OpenVPN-based servers/clients, but have yet to server-admin such systems. Otherwise, experienced Linux sysadmin. Target system: Ubuntu, probably 12.04. Seeking to put an OpenVPN process on above server to "protect" all the above-mentioned services, enabling only OpenVPN-authorized clients/processes to access above services. (Can easily acquire additional IP address(es) as needed for this setup.) Option: if absolutely needed, can employ an additional, dedicated, "VPN server" VPS simply to be my VPN server "front end." But prefer to have all server processes (VPN server plus other server apps) all running on same machine, if possible. Will consider further if dedicated-VPN-machine setup enables 1. easier installation/administration, 2. better/easier end-user experience, and/or 3. makes system significantly more secure. Any of above feasible? The main intention: create a VPN from purely-hosted resources, and not spend all the effort to make a non-VPN, secure site--which typically means "SSL wrapping" + all the continual webserver-application-update management. Let the VPN server deal with access security, and spend list time pushing said security "down" in the other apps/Apache.

  Read the article

< Previous Page | 472 473 474 475 476 477 478 479 480 481 482 483  | Next Page >