Search Results

Search found 26097 results on 1044 pages for 'network share'.

Page 48/1044 | < Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >

  • bridge to share WiFi internet connection over eth0

    - by rubo77
    In this script there is implemented that you create a mesh network and connect other machines to your device to serve an internet connection with dhcp: echo "starting bridge to share internet connection over eth0" ifconfig eth0 up promisc brctl addbr br-freifunk brctl addif br-freifunk bat0 brctl addif br-freifunk eth0 echo "internet starting, this may take some minutes due to latency..." echo "(use" echo "tail -f /var/log/syslog" echo "in another window for debugging)" echo echo dhclient br-freifunk echo "The error 'Rather than invoking init scripts through /etc/init.d...' can be ignored:" dhclient br-freifunk # without bridge: dhclient bat0 This works fine with the freifunk-mesh network. But how can I serve internet in a normal case? I would like to connect to any open Wifi I find with my network-manager or wicd (yes, with the graphical GUI) and then start a small script that creates a bridge to my network-out on my laptop I use Ubuntu and my networkcards are eth0 and wlan0

    Read the article

  • Ubuntu 10.04 network manager issues

    - by Shark
    I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

    Read the article

  • ubuntu 12.04 kvm virtual server network setup, can't get the machine to be connectable

    - by xyious
    I have worked on my Ubuntu Server host for weeks now and I just can not manage to get the virtual machines into the network.... here's what I need to do: I need to be able to create virtual machines that have IP addresses that can be reached from the outside (192.168 network). I need to be able to connect to the virtual machines through ssh, ftp, http and preferably https, anything else doesn't matter that much. So far everything seems simple enough and I have a lot of leeway in terms of IP address range and server/client configuration. I have the option of taking part of a /24 net as most IPs aren't used, and if it's absolutely necessary I have the option of creating a new /24 subnet. Also have the option of reformatting and reinstalling OS on the host and recreating the virtual machines as nothing has been done other than trying to get virtual machines to work. I would prefer if the virtual machines were just part of the normal network which would be 192.168.5.0/24. The host machine has 2 network cards so I don't even necessarily need the Host to be connectable in the same /24 network. I have tried (I think) just about everything from about 5 different tutorials on bridging (giving br0 the same IP that eth0 used to have (Host is able to connect to VM and vice versa, VM doesn't have outside network access), having eth0 set up like it always was and having br0 have a different IP (same as above), NAT with port forwarding (which I would have preferred not to use but will if it works), turning off one of the hosts network cards and just using one of them, different subnets.... etc. I do know my way around iptables fairly well.... Host is 64bit Ubuntu Server 12.04, using libvirt/kvm. edits: Local network is 192.168.5.0/24, host has static ip 192.168.5.254, GW .5.1 which is also nameserver. We have a second Local network at 192.168.10.0/24 with .10.1 GW, but both hosts and VMs were supposed to go into the .5 subnet. The .10 subnet isn't required, but it wouldn't be horrible if the Host were only accessible in the .10 subnet.

    Read the article

  • Hyper-V share a folder between host and instance

    - by Fly_Trap
    I have a hyper-v server and several VM's (Virtual Machines). All the VM's are connected to an external network. I have tried to share a folder on the host and connect via the VM, I can do this but I'm prompted for a user name and password (as you would expect). I do not want to enable the "Everyone" group permissions as the physical host server is on a network of other servers. I have created a new virtual internal network in Hyper-V and given it's adapter a static ip of 33.0.0.100. I have added the virtual adapter to one of the VM's and set to IP to 33.0.0.2 (as advised here). Again this seems to work but I'm still prompted for a user name and password. Am I on the right lines here? I just want to share a directory from the host to the vm's without exposing the share to other servers on the network.

    Read the article

  • Find only physical network adapters with WMI Win32_NetworkAdapter class

    - by Mladen Prajdic
    WMI is Windows Management Instrumentation infrastructure for managing data and machines. We can access it by using WQL (WMI querying language or SQL for WMI). One thing to remember from the WQL link is that it doesn't support ORDER BY. This means that when you do SELECT * FROM wmiObject, the returned order of the objects is not guaranteed. It can return adapters in different order based on logged-in user, permissions of that user, etc… This is not documented anywhere that I've looked and is derived just from my observations. To get network adapters we have to query the Win32_NetworkAdapter class. This returns us all network adapters that windows detect, real and virtual ones, however it only supplies IPv4 data. I've tried various methods of combining properties that are common on all systems since Windows XP. The first thing to do to remove all virtual adapters (like tunneling, WAN miniports, etc…) created by Microsoft. We do this by adding WHERE Manufacturer!='Microsoft' to our WMI query. This greatly narrows the number of adapters we have to work with. Just on my machine it went from 20 adapters to 5. What was left were one real physical Realtek LAN adapter, 2 virtual adapters installed by VMware and 2 virtual adapters installed by VirtualBox. If you read the Win32_NetworkAdapter help page you'd notice that there's an AdapterType that enumerates various adapter types like LAN or Wireless and AdapterTypeID that gives you the same information as AdapterType only in integer form. The dirty little secret is that these 2 properties don't work. They are both hardcoded, AdapterTypeID to "0" and AdapterType to "Ethernet 802.3". The only exceptions I've seen so far are adapters that have no values at all for the two properties, "RAS Async Adapter" that has values of AdapterType = "Wide Area Network" and AdapterTypeID = "3" and various tunneling adapters that have values of AdapterType = "Tunnel" and AdapterTypeID = "15". In the help docs there isn't even a value for 15. So this property was of no help. Next property to give hope is NetConnectionId. This is the name of the network connection as it appears in the Control Panel -> Network Connections. Problem is this value is also localized into various languages and can have different names for different connection. So both of these properties don't help and we haven't even started talking about eliminating virtual adapters. Same as the previous one this property was also of no help. Next two properties I checked were ConfigManagerErrorCode and NetConnectionStatus in hopes of finding disabled and disconnected adapters. If an adapter is enabled but disconnected the ConfigManagerErrorCode = 0 with different NetConnectionStatus. If the adapter is disabled it reports ConfigManagerErrorCode = 22. This looked like a win by using (ConfigManagerErrorCode=0 or ConfigManagerErrorCode=22) in our condition. This way we get enabled (connected and disconnected adapters). Problem with all of the above properties is that none of them filter out the virtual adapters installed by virtualization software like VMware and VirtualBox. The last property to give hope is PNPDeviceID. There's an interesting observation about physical and virtual adapters with this property. Every virtual adapter PNPDeviceID starts with "ROOT\". Even VMware and VirtualBox ones. There were some really, really old physical adapters that had PNPDeviceID starting with "ROOT\" but those were in pre win XP era AFAIK. Since my minimum system to check was Windows XP SP2 I didn't have to worry about those. The only virtual adapter I've seen to not have PNPDeviceID start with "ROOT\" is the RAS Async Adapter for Wide Area Network. But because it is made by Microsoft we've eliminated it with the first condition for the manufacturer. Using the PNPDeviceID has so far proven to be really effective and I've tested it on over 20 different computers of various configurations from Windows XP laptops with wireless and bluetooth cards to virtualized Windows 2008 R2 servers. So far it always worked as expected. I will appreciate you letting me know if you find a configuration where it doesn't work. Let's see some C# code how to do this: ManagementObjectSearcher mos = null;// WHERE Manufacturer!='Microsoft' removes all of the // Microsoft provided virtual adapters like tunneling, miniports, and Wide Area Network adapters.mos = new ManagementObjectSearcher(@"SELECT * FROM Win32_NetworkAdapter WHERE Manufacturer != 'Microsoft'");// Trying the ConfigManagerErrorCode and NetConnectionStatus variations // proved to still not be enough and it returns adapters installed by // the virtualization software like VMWare and VirtualBox// ConfigManagerErrorCode = 0 -> Device is working properly. This covers enabled and/or disconnected devices// ConfigManagerErrorCode = 22 AND NetConnectionStatus = 0 -> Device is disabled and Disconnected. // Some virtual devices report ConfigManagerErrorCode = 22 (disabled) and some other NetConnectionStatus than 0mos = new ManagementObjectSearcher(@"SELECT * FROM Win32_NetworkAdapter WHERE Manufacturer != 'Microsoft' AND (ConfigManagerErrorCode = 0 OR (ConfigManagerErrorCode = 22 AND NetConnectionStatus = 0))");// Final solution with filtering on the Manufacturer and PNPDeviceID not starting with "ROOT\"// Physical devices have PNPDeviceID starting with "PCI\" or something else besides "ROOT\"mos = new ManagementObjectSearcher(@"SELECT * FROM Win32_NetworkAdapter WHERE Manufacturer != 'Microsoft' AND NOT PNPDeviceID LIKE 'ROOT\\%'");// Get the physical adapters and sort them by their index. // This is needed because they're not sorted by defaultIList<ManagementObject> managementObjectList = mos.Get() .Cast<ManagementObject>() .OrderBy(p => Convert.ToUInt32(p.Properties["Index"].Value)) .ToList();// Let's just show all the properties for all physical adapters.foreach (ManagementObject mo in managementObjectList){ foreach (PropertyData pd in mo.Properties) Console.WriteLine(pd.Name + ": " + (pd.Value ?? "N/A"));}   That's it. Hope this helps you in some way.

    Read the article

  • networking disabled

    - by Parimal
    hi i have internet working but the network manager applet in the ubuntu 10.10 says that it is disabled and i am not able to enable it however i have previously forced the ip address which i am still getting in ifconfig but in wired section of network connections there is no such interface as eth0 where can i see these settings and how can i enable the etwork manager applet in the title bar thanks in advance

    Read the article

  • Realtek RTL8111/8168B wired network doesn't work anymore

    - by Radar4002
    This sounds like it's a common problem upgrading 11.04, but I am having trouble finding a common solution, and one that will work for me. I just applied updates via the update manager and now my wired network connection is down. I know Ubuntu network settings is the issue, because I have a dual-boot with Win 7 and my network/internet is fine on Win 7. I don't know too much about networking, so what can I do to trouble shoot this issue? I can choose an older grub version, 2.6.38-8 instead of 2.6.38-11 and this does not resolve the issue. Here is my lspci result: 00:00.0 Host bridge: ATI Technologies Inc RD890 Northbridge only single slot PCI-e GFX Hydra part (rev 02) 00:02.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port B) 00:04.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port D) 00:05.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port E) 00:06.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port F) 00:07.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port G) 00:09.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port H) 00:0a.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx1 port A) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] (rev 40) 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 41) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:15.0 PCI bridge: ATI Technologies Inc Device 43a0 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5700 Series] 01:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 02:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 07:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 07:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 08:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) 09:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 09:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) Here is my sudo lshw -class network: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 03 serial: 6c:f0:49:e7:72:e8 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:9e00(size=256) memory:fceff000-fcefffff memory:fcef8000-fcefbfff memory:fce00000-fce1ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth1 version: 03 serial: 6c:f0:49:e7:72:ea size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:8e00(size=256) memory:fddff000-fddfffff memory:fddf8000-fddfbfff memory:fdd00000-fdd1ffff

    Read the article

  • Oracle Social Network Developer Challenge: Fishbowl Solutions

    - by Kellsey Ruppel
    Originally posted by Jake Kuramoto on The Apps Lab blog. Today, I give you the final entry in the Oracle Social Network Developer Challenge, held last week during OpenWorld. This one comes from Friend of the ‘Lab and Fishbowl Solutions (@fishbowle20) hacker, John Sim (@jrsim_uix), whom you might remember from his XBox Kinect demo at COLLABORATE 12 (presentation slides and abstract) hacks and other exploits with WebCenter. We put this challenge together specifically for developers like John, who like to experiment with new tools and push the envelope of what’s possible and build cool things, and as you can see from his entry John did just that, mashing together Google Maps and Oracle Social Network into a mobile app built with PhoneGap that uses the device’s camera and GPS to keep teams on the move in touch. He calls it a Mobile GeoTagging Solution, but I think Avengers Assemble! would have equally descriptive, given that was obviously his inspiration. Here’s his description of the mobile app: My proposed solution was to design and simplify GeoLocation mapping, and automate updates for users and teams on the move; who don’t have access to a laptop or want to take their ipads out – but allow them to make quick updates to OSN and upload photos taken from their mobile device – there and then. As part of this; the plan was to include a rules engine that could be configured by the user to allow the device to automatically update and post messages when they arrived at a set location(s). Inspiration for this came from on{x} – automate your life. Unfortunately, John didn’t make it to the conference to show off his hard work in person, but luckily, he had a colleague from Fishbowl and a video to showcase his work.    Here are some shots of John’s mobile app for your viewing pleasure: John’s thinking is sound. Geolocation is usually relegated to consumer use cases, thanks to services like foursquare, but distributed teams working on projects out in the world definitely need a way to stay in contact. Consider a construction job. Different contractors all converge on a single location, and time is money. Rather than calling or texting each other and risking a distracted driving accident, an app like John’s allows everyone on the job to see exactly where the other contractors are. Using his GPS rules, they could easily be notified about how close each is to the site, definitely useful when you have a flooring contractor sitting idle, waiting for an electrician to finish the wiring. The best part is that the project manager or general contractor could stay updated on all the action (or inaction) using Oracle Social Network, either sitting at a desk using the browser app or desktop client or on the go, using one of the native mobile apps built for Oracle Social Network. I can see this being used by insurance adjusters too, and really any team that, erm, assembles at a given spot. Of course, it’s also useful for meeting at the pub after the day’s work is done. Beyond people, this solution could also be implemented for physical objects that are in route to a destination. Say you’re a customer waiting on rail shipment or a package delivery. You could track your valuable’s whereabouts easily as they report their progress via checkins. If they deviated from the GPS rules, you’d be notified. You might even be able to get a picture into Oracle Social Network with some light hacking. Thanks to John and his colleagues at Fishbowl for participating in our challenge. We hope everyone had a good experience. Make sure to check out John’s blog post on his work and the experience using Oracle Social Network. Although this is the final, official entry we had, tomorrow, I’ll show you the work of someone who finished code, but wasn’t able to make the judging event. Stay tuned.

    Read the article

  • How do you access timemachine backups of a different computer?

    - by baloo
    I'm currently backing up using WD My Book World network drive that supports Apple Time Machine. I would like to copy some files from my old laptop backup. However, my old backup isn't showing when you browse the time machine network drive, only the currently used machine is listed (I know there are 3 different backups). How can I access those files not belonging to the currently used laptop?

    Read the article

  • How do you access timemachine backups of a different computer?

    - by baloo
    I'm currently backing up using WD My Book World network drive that supports Apple Time Machine. I would like to copy some files from my old laptop backup. However, my old backup isn't showing when you browse the time machine network drive, only the currently used machine is listed (I know there are 3 different backups). How can I access those files not belonging to the currently used laptop?

    Read the article

  • Improve file transfer speed between Windows PCs and servers

    - by Geotarget
    I've setup a server which I've connected to multiple PCs in my workplace. Sadly, data transfer speeds are at max 3 MB/sec per connection which works out slow for file transfers, especially when transferring large files. I'm using Windows filesharing and the server is a Windows Server 2008 (2 Ghz CPU, 1 GB RAM) and the client PCs mostly running Windows 7. How can I detect bottlenecks in my network and improve file sharing speed within the network?

    Read the article

  • Redhat | Openssl installation error

    - by MMRUser
    make -f objs/Makefile make[1]: Entering directory `/root/fuse-ssh/nginx-0.7.65' cd /usr/bin/openssl \ && make clean \ && ./config --prefix=/usr/bin/openssl/.openssl no-shared no-threads \ && make \ && make install /bin/sh: line 0: cd: /usr/bin/openssl: Not a directory make[1]: *** [/usr/bin/openssl/.openssl/include/openssl/ssl.h] Error 1 make[1]: Leaving directory `/root/fuse-ssh/nginx-0.7.65' make: *** [build] Error 2 where's the actual location of openssl, there are several different places in my system.. How to solve this issue. rpm -ql openssl /usr/bin/openssl /usr/lib64/openssl /usr/lib64/openssl/engines /usr/lib64/openssl/engines/lib4758cca.so /usr/lib64/openssl/engines/libaep.so /usr/lib64/openssl/engines/libatalla.so /usr/lib64/openssl/engines/libchil.so /usr/lib64/openssl/engines/libcswift.so /usr/lib64/openssl/engines/libgmp.so /usr/lib64/openssl/engines/libnuron.so /usr/lib64/openssl/engines/libsureware.so /usr/lib64/openssl/engines/libubsec.so /usr/share/doc/openssl-0.9.8e /usr/share/doc/openssl-0.9.8e/CHANGES /usr/share/doc/openssl-0.9.8e/FAQ /usr/share/doc/openssl-0.9.8e/INSTALL /usr/share/doc/openssl-0.9.8e/LICENSE /usr/share/doc/openssl-0.9.8e/NEWS /usr/share/doc/openssl-0.9.8e/README /usr/share/doc/openssl-0.9.8e/README.FIPS /usr/share/doc/openssl-0.9.8e/c-indentation.el /usr/share/doc/openssl-0.9.8e/openssl.txt /usr/share/doc/openssl-0.9.8e/openssl_button.gif /usr/share/doc/openssl-0.9.8e/openssl_button.html /usr/share/doc/openssl-0.9.8e/ssleay.txt /usr/bin/openssl /usr/lib/openssl /usr/lib/openssl/engines /usr/lib/openssl/engines/lib4758cca.so /usr/lib/openssl/engines/libaep.so /usr/lib/openssl/engines/libatalla.so /usr/lib/openssl/engines/libchil.so /usr/lib/openssl/engines/libcswift.so /usr/lib/openssl/engines/libgmp.so /usr/lib/openssl/engines/libnuron.so /usr/lib/openssl/engines/libsureware.so /usr/lib/openssl/engines/libubsec.so /usr/share/doc/openssl-0.9.8e /usr/share/doc/openssl-0.9.8e/CHANGES /usr/share/doc/openssl-0.9.8e/FAQ /usr/share/doc/openssl-0.9.8e/INSTALL /usr/share/doc/openssl-0.9.8e/LICENSE /usr/share/doc/openssl-0.9.8e/NEWS /usr/share/doc/openssl-0.9.8e/README /usr/share/doc/openssl-0.9.8e/README.FIPS /usr/share/doc/openssl-0.9.8e/c-indentation.el /usr/share/doc/openssl-0.9.8e/openssl.txt /usr/share/doc/openssl-0.9.8e/openssl_button.gif /usr/share/doc/openssl-0.9.8e/openssl_button.html /usr/share/doc/openssl-0.9.8e/ssleay.txt These are the places.. Thanks.

    Read the article

  • Samba Share - MS Excel when saved (can't access the file, there are several possible reasons)

    - by brain90
    Dear Fellow ServerFaulter, I have a weird problem in my samba share. I have one share definition for 3 client (A,B,C) This share contain some excel file which having a lot of formula and linked each other. Client A access the file with libre office (ubuntu), client B access with WinXP & MS Office 2003, The write and read process working successfuly on Both of them. The problem occur when client C accessing the same file with MS Excel 2003 (windows xp). This messagebox appear when he saving the file : Microsoft office excel cannot access the \\192.168.1.23\myshare\ There are several possible reasons: - The File ort path does not exist The file is being used by another program. - The workbook you are trying to save has the same name as a - Currently open workbooks. I was trying http://support.microsoft.com/kb/291204 but it didnt work. Below is my share definition : [brainshare] comment = brainshare path = /opt/brainshare/ valid users = @brainshare force group = brainshare read only = No create mask = 0775 veto files = /*.scr/*.eml/thumbs.com/ Help me please... Thanks in advance ! Server: Ubuntu 10.10, Samba version 3.5.4

    Read the article

  • Can't connect to Apple Time Capsule in home network using Home Plugs from Win 7 Machine

    - by Eugene
    I have the following home network setup with subnet 255.255.255.0 but recently moved my time capsule to a different location when I added a third Home Plug and can no longer ping or map a network drive to it from the Windows 7 Machine. However using Airport Utility on the Windows 7 machine I can manually configure the Time Capsule. Using a Macbook on WIFI Network 1 or 2 - I can backup to the time capsule, so its accessible via both the router wifi network and the time capsule wifi network. The Time Capsule is set to BRIDGE function - ie no NAT or DHCP server enabled. Any bright sparks out there that can help diagnose the problem? Router (192.168.1.254) WIFI Network 1 | | |---- Home Plug one |---- Home Plug Two | |---- Computer A Windows 7 (192.168.1.160) | |---- Printer (192.168.1.69) |---- Home Plug Three | |---- Apple Time Capsule (192.168.1.150) WIFI Network 2 |---- Smart TV (192.168.1.70) | |---- Apple TV (192.168.1.4)

    Read the article

  • msi netbook refuses to connect to home wireless network (windows xp)

    - by sa125
    Hi - I'm trying to connect my girlfriend's MSI netbook to the wireless network in my house, and failing repeatedly. It's not a hardware issue, b/c it connects to other networks successfully, and, it's not a network issue, because I have another mac and linux laptops that have no problem detecting and connecting to the same network. When I open windows' network connections box, I can see the network available, and when I try to connect to it (using a password), I get a "network no longer in range.." error (the router is 2 ft away). This has been the case for the past 6 months, and I'm about to give up. I've reset the router, erased all saved network preferences and pretty much all I could think of short of re-installing XP. Any idea what else could be done? thanks.

    Read the article

  • MSI netbook refuses to connect to home wireless network with Windows XP

    - by sa125
    I'm trying to connect my girlfriend's MSI netbook to the wireless network in my house, and failing repeatedly. It's not a hardware issue, b/c it connects to other networks successfully, and, it's not a network issue, because I have another mac and linux laptops that have no problem detecting and connecting to the same network. When I open windows' network connections box, I can see the network available, and when I try to connect to it (using a password), I get a "network no longer in range.." error (the router is 2 ft away). This has been the case for the past 6 months, and I'm about to give up. I've reset the router, erased all saved network preferences and pretty much all I could think of short of re-installing XP. Any idea what else could be done? thanks.

    Read the article

  • Can't write to samba share

    - by Tiddo
    I try to setup a samba file server, but whatever I do I can't get write access to work (reading works fine). This is my current situation: I have a local fileserver with 3 harddisks mounted at /mnt/share/disk<nr>. 2 of these use the ext4 filesystem, the third one is ntfs. This file server runs Fedora 18 32-bit. The root folders of these harddisks are owned by superman:superman, and testparm outputs the following: [global] workgroup = WORKGROUP netbios name = FILE_SERVER server string = Samba Server Version %v interfaces = lo, eth0, 192.168.123.191/8 log file = /var/log/samba/log.%m max log size = 50 unix extensions = No load printers = No idmap config * : backend = tdb hosts allow = 192.168.123. cups options = raw wide links = Yes [share] comment = Home Directories path = /home/share/ write list = superman, @users force user = superman read only = No create mask = 0777 directory mask = 0777 inherit permissions = Yes guest ok = Yes I've tried a lot to get this to work: the disk are chmodded to 777, I've tried turning off selinux, I've added the samba_share_t label to the disks and as can be seen in the above output I tried to make the smb config as permissive as I could, but still I cannot write to the share (tried from Windows 7 and another Fedora installation). What can I try to be able to write to the shares? EDIT: The replies I got so far are mostly concerned with the smb.conf. I have however tried a lot of different setup, ready made configs, and solutions to similar problems for the smb.conf file, so I suspect that the real problem is somewhere else.

    Read the article

  • Share Firefox/Thnderbird data between W7 and Linux Mint 12 in dual boot computer

    - by Albert
    I've just set up my laptop (where I had running only W7) with a dual boot to run Linux Mint 12 as well. I have a "Data" partition (apart from the required partitions for W7 and Linux) where I store pretty much everything that isn't software installations (music, videos, project files, etc). I seem to be able to access that NTFS partition totally fine from Mint (like I've always done with W7), which is cool because I can access all that stuff regardless of which OS I'm using. I would like to know if it's possible (and how) to go one step further and share programs data between the two OS. One example would be my Firefox and Thunderbird data. For example, in Firefox share my bookmarks (and if I could share history, autocomplete and all that stuff, that would be awesome). In thunderbird, be able to share my mail and configuration, seeing the same inbox, folders, message rules, etc... So if I receive/send an email from W7 and later switch to Mint, I can see that email as it had been received/sent from Mint, and vice versa. Is this even possible? Or am I asking for too much convenience? If it's possible, any clues on how to set it all up?

    Read the article

  • DVD Share on Vista Home Premium Failing

    - by hpunyon
    UPDATE: - I can't find any Local Policy Editor for Vista Home Premium, as suggested. - I did learn about registry keys: allocatecdroms, allocatefloppies, allocatedasd and tried adding these keys (individually and collectively) and setting them to both 0 or 1. There was no positive affect on read access to the DVD root folder - always Access Denied. ORIGINAL POST: Failing read access to the root folder of a DVD drive in Vista Home Premium laptop using the Guest account - Access Denied. The client is an XP Home PC that can see, but not access, the data in the share. I'm only trying to read the data DVD - not trying to write/burn anything. On the Vista laptop, I have: All Firewalls and Antivirus disabled.UAC disabled. Password checking disabled. "Advanced Shared" the DVD drive, with "Everyone" having full-access permissions to the share. Tried adding Guest and Anonymous users having full-access permissions to the share. RestrictAnonymous=0 set in the registry. Both PC's are in the same workgroup (MSHOME) The XP Home client sees the shared DVD in \Vista_Hostname\ but when I double click the drive icon on the client, I get a popup that access is denied, check with the administrator, etc. I can share other folders on the Vista PC and see and READ these from the XP Home client. If I enable password checking on the Vista side, I get a user/password popup, and I can authenticate (using my known Vista account, that happens to have Admin rights) and then I can get to see and read the DVD data. I need to open this up so that the (default) Guest user can see and access the DVD data files.

    Read the article

  • Samba share will not connect (was working yesterday)

    - by David Gard
    I have a CentOS websver with a Samba share set up (\\webserver\websites). I was connected to this share just yesterday without issue, but today my Windows 8 PC will not connect to it. I've also tried making a connection from Windows 7 and Windows XP, all without success. I initially tried restarting my computer, but that did not work. I then tried restarting the Samba service on the webserver (service smb restart), and when that failed I restarted the webserver. All of that was to no avail, and I still cannot connect to the share. The webserver is contactable from my PC (and the others I tried), as the websites it hosts work fine and I'm able to Putty to the server. When connected to the webserver, I can see that Samba is running by using service smb status - service smb status smbd (pid 4685) is running... nmbd (pid 4688) is running... Can anyone please help me to get this share working? Here is my full Samba config (/etc/samba/smb.conf) - [global] workgroup = MYGROUP server string = Samba Server %v log file = /var/log/samba/log.%m max log size = 50 security = user encrypt passwords = yes socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192 local master = no [websites] comment = Websites browseable = yes writable = yes path=/var/www/html/ valid users = dgard

    Read the article

  • On a local network, are you able to password protect certain folders and how (in windows xp)?

    - by Derek
    I have a local network set up for my small office which consists of me, the manager, my wife, the secretary, and a few sales people/others. I would like to share passwords over the network and other such things privately to my wife, the secretary, but would not like the sales people and others to have access to it, yet I need the others to have access to other folders/documents that I'd like to share. How would I go about doing this if not by password? Thanks in advance

    Read the article

  • Share one ssl certificate between multiples vhost

    - by Cesar
    I have a setup like this: <VirtualHost 192.168.1.104:80> ServerName domain1 DocumentRoot /home/domain/public_html ... </VirtualHost> <VirtualHost 192.168.1.104:80> ServerName domain2 DocumentRoot /home/domain2/public_html ... </VirtualHost> <VirtualHost 192.168.1.104:80> DocumentRoot /home/domain3/public_html ServerName domain3 ... </VirtualHost> <VirtualHost 192.168.1.104:443> ServerName domain3 SSLCertificateFile /usr/share/ssl/certs/certificate.crt SSLCertificateKeyFile /usr/share/ssl/private/private.key SSLCACertificateFile /usr/share/ssl/certs/bundle.cabundle ... </VirtualHost> I want to use domain3 certificate in the other domains, preferably without having to repeat all the <VirtualHost 192.168.1.104:443> config. In other words I want something like this: If the vhost has no explicit ssl config use cert for domain3 (/usr/share/ssl/certs/certificate.crt) Notes: 1.- I for sure will be setting more vhosts in the future 2.- I know (and don't care) of the ssl warnings the browser will show (hostname mismatch) If this possible? how?

    Read the article

  • Can a Linux system crash cause network issues?

    - by Supratik
    I have a Ubuntu box in my network which crashed, all the system connected to the switch in which the Ubuntu system was connected started giving problem. I removed that system from the network, since that was the last change I made in my network and everything was fine. So, to confirm this I again connected the system back to the network and the same network outage happened. When I checked the links it was fine. When I rebooted the problematic system and again connected back to the network switch everything started working. I think possibly the crash of the Ubuntu system could have caused this outage. Is there any possibility that a kernel crash can cause network issues?

    Read the article

  • How can I tell why I have access to a file share on Windows Server

    - by Joel
    I have a file share on a Windows 2008 R2 server in a AD domain (call it \SECURESERVER\STUFF) and I am not sure if I have the share and folder permissions set up right. I noticed the problem when I set up new server (WORKGROUP\FOREIGNSERVER) that was not joined to the domain and tried to copy some files off of \SECURESERVER\STUFF. I was surprised to find that when I tried to access the files, it did not prompt me for a username and password and proceeded to give me full access to the files. That worried me so I tried the same thing on some workstations that were not in the domain and they did NOT have the same behavior (they did prompt for a username/password as desired/expected). So, I think there is something peculiar about FOREIGNSERVER. I am logging into it with a local admin account, but my domain and SECURESERVER should know nothing of this server. I've carefully gone through the share and folder permissions on the share but I can't find the reason that FOREIGNSERVER has access. How can I find out why FOREIGNSERVER has access to SECURESERVER?

    Read the article

  • windows xp cannot access admin share

    - by barlop
    I have 3 systems. A,B,Compx all on xp. but comps A and B have an issue with Compx. Compx has network shares I can access. I can do \\compx and get some. But I cannot access the admin share c$ \\compx\c$ gives a login prompt, and I can't get any user/pass to work. I looked at permissions but don't see an issue. Nevertheless, I will describe what I see in the permissions. In the security tab of C, I have Administrators,creator owner,everyone,bob,system,users (6 things there) "creator owner" has nothing ticked, I can't seem to change that. If I tick so they all get ticked, and click apply, 2.5min and it's completed its opration and they all untick. Though this isn't the root of the problem. Since I get the same in the share I can access. In advanced, I see those 6 things, Administrators,creator owner,everyone,bob,system,users (6 things there) all "full control" all are "this folder, subfolders and files".. except creator owner, which is just subfolders and files only I look at the properties for the share I can see. looks the same, except in security..advanced, double clicking any of them the boxes are all ticked but greyed. That's not the problem though since I can access that share. So, I don't know what the problem is.

    Read the article

< Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >