Search Results

Search found 6200 results on 248 pages for 'recovery partition'.

Page 48/248 | < Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >

• Hard Drive upgrade advice for a Dell PowerEdge 1950

  - by user8185

  My setup is a Dell PowerEdge 1950 with 2x 140Gb Hard drives in a RAID 1 configuration. The OS is Windows 2003 Web Edition and disk is partitioned into to two, a 12Gb C: partition and the remainder is the D: drive. Both are very close to full capacity. Ideally I want to replace those drives with 2x 1Tb drives while retaining all data. First of all is this possible without rebuilding the server? If so, will I need any 3rd party software, Symantec Ghost, Partition Master for e.g., to do this? Any general advice as to how to go about doing this?

  Read the article

• Infected Win XP disk not openable on a Vista computer

  - by Retired57

  How can I read a WinXP partioned disk that is infected and shows up on a USB connection to Win Vista computer as a single partition that Vista cannot see the contents? The XP computer HDD is partioned into 4 partitions. It became infected, and all attempts to clean it have failed. Applications begin to launch, but are then shut down by the infecting agent. Using a major Anti-virus Co. boot disk (which was unable to connect to the Web, probably because the infecting agent stopped it) with virus definitions dated after the disk became infected, the resultant scan showed no infection. I bought a USB cable to connect the IDE drive to my Vista computer, but when I open Win Explorer, it sees the disk, but does not show any contents. It indicates it is a single partition that is valid. However in all the ways I have tried it does not show drive contents. Any suggestions on what to do next?

  Read the article

• Dead-simple USB-based Windows partition cloner?

  - by OverTheRainbow

  Clonezilla is a fine open-source tool, but it requires going through several screens. Since I need to save/restore the same Windows partition, I was wondering if someone knew of a tool (open-source or not) that is easier to use and boots off a USB keydrive. Ideally, it'll save the two commands to save/restore a partition, so I just need to boot the host from the USB key, choose the command, and it'll take care of business. Are there solutions that look like this? Thank you. Edit: Here's one among other articles that shows how to tell CZ to run a script to avoid the multiple screens.

  Read the article

• How to resize a ubuntu partition to make more room for windows

  - by Jeremy

  My laptop has Windows 7 and Ubuntu 13.10 installed alongside each other. My laptop has two 225GB hard drives. I give Ubuntu 133.65GB and I give Windows 87.76GB on the same hard drive (C). My problem now is that Windows is almost out of space but Ubuntu is only using a few GB of the 133.65GB that I gave it. I want to reduce Ubuntu's partition size and give that space to increase Windows partition size. Is that any program that can to do this?

  Read the article

• Running projects from NTFS partition on Ubuntu

  - by tsuby

  I'm dual booting Windows 7/Ubuntu 12.04. I want to run C++/Java projects from a NTFS partition, where I keep generally all my files and projects. I fiddled with the fstab. One time I removed 'noexec', the other I changed it to 'exec'. After that,each time, I remounted the partition and it still didn't work. I tried using sudo mount -o remount,exec /media/mypartition It didn't work either. There was a somewhat similar question already, but it didn't have the proper answer for me or I didn't know how to make it work(note: I am a total newbie with Ubuntu and Linux in general).

  Read the article

• How to make a drive partition and install Windows on it from an HP install disc

  - by Zohaib

  I bought a new HP DV6-S190SE, and I want to make multiple partitions on the hard drive. I went to HP's site and discussed with them using online chat. They said that this is not useful to make more than one partition, as when you recover your windows after some time it will erase/delete all files including new partitions, so this would not be very usefull for you. Now, if there is there any way to get rid of the existing structure and install Windows only on the C drive? First of all, how do I partition the harddrive?

  Read the article

• df says disk is full, but it is not

  - by Chris

  On a virtualized server running Ubuntu 10.04, df reports the following: # df -h Filesystem Size Used Avail Use% Mounted on /dev/sda1 7.4G 7.0G 0 100% / none 498M 160K 498M 1% /dev none 500M 0 500M 0% /dev/shm none 500M 92K 500M 1% /var/run none 500M 0 500M 0% /var/lock none 500M 0 500M 0% /lib/init/rw /dev/sda3 917G 305G 566G 36% /home This is puzzling me for two reasons: 1.) df says that /dev/sda1, mounted at /, has a 7.4 gigabyte capacity, of which only 7.0 gigabytes are in use, yet it reports / being 100 percent full; and 2.) I can create files on / so it clearly does have space left. Possibly relevant is that the directory /www is a symbolic link to /home/www, which is on a different partition (/dev/sda3, mounted at /home). Can anyone offer suggestions on what might be going on here? The server appears to be working without issue, but I want to make sure there's not a problem with the partition table, file systems or something else which might result in implosion (or explosion) later.

  Read the article

• Windows 7 Refuses To Install To A Partition

  - by PP

  I have 4 HDDs in my PC on a Gigabyte EP45-UD3 rev1.0 motherboard on SATA ports 0-3 and running AHCI mode. Windows 7 refuses to let me install to any partitions or disks I select saying Setup was unable to create a new system partition or locate an existing system partition. I will get to the bottom of this, after I sacrifice my Friday nights and weekends to Microsoft (they don't just want my money, they want my soul). Keep tuned, if no one has the answer, I will find one. I suspect I have to rip out 3 HDDs so that the n00bs at Microsoft can actually deal with spinning media. Really angers me how paid-for-products are so inferior to Linux they don't even qualify to be called "software".

  Read the article

• Change Apache DocumentDirectory path in trueCrypt partition

  - by Alan C

  Hello, I'm recently moving from windows to linux, so I've setup my machine to dual boot Windows7 and Ubuntu 10.04. I was able to successfully setup Apache on the Ubuntu partition, but I need to move the DocumentRoot since my websites are on a TrueCrypt partition that is in another hard drive so I can have them accessible in both OS. I followed some guides on how to change the path for the DocumentRoot so I end up modifiying the default file at /etc/apache2/sites-available DocumentRoot /media/truecrypt1/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /media/truecrypt1/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> Those are the lines that I've changed, but now when I go to localhost I always get the Forbidden You don't have permission to access / on this server. Apache/2.2.14 (Ubuntu) Server at localhost Port 80

  Read the article

• Windows 7 installer doesn't recognize NTFS partition.

  - by ifesdjeen

  Hi, I'm trying to install windows 7 on my Macbook. I've created NTFS partition, but when i'm starting up Windows 7 installation, it says that i can't install windows on this partition, since drive already contains maximum amount of partitions with this filesystem type. I haven't heard of any limits on filesystems, but still i can't even format this drive from Win7 installer. I've found access to command line from win7 installation CD, but i can't find fdisk there to format. Do you have any idea on about how to deal with it?

  Read the article

• Best Partitioning Software

  - by Cenoc

  Now that PartionMagic seems to have died, I was wondering, what do you guys think is the best Partition Software?

  Read the article

• MacBook Air with Bootcamp - How to partition?

  - by Andrew

  I want to buy a MacBook Air for my wife with a 128GB SSD. She has to use Windows 7 but I would like to keep OS X for myself to use somtimes. Using Bootcamp, is it feasible to install the following? Mac partition: 36GB with Mac OS X and Microsoft Office 2011 Word, Excel & Powerpoint and Skype. (minimal use) Windows partition: 92GB with Windows 7 professional and Microsoft Office 2010 Word, Excel & Powerpoint, and Skype (daily use) Media to be kept on SD card or external USB3 drive. (Note: Using Parrallels may save space, but my wife won't go for the user experience)

  Read the article

• How to partition my hard drive, quicker?

  - by Sam

  When I install Windows 7 on my hard drive, it makes three partitions. One with the OS itself, one with bootmgr inside (that is 100 MiB), and one with the factory image (all the crapware from HP). My final goal is to have the OS on a partition of 100 GiB and keep the rest (900 GiB) for storage. I thought it would be easy using gparted, but it is taking so long. It will take hours. There must a way to partition the drive before installing Windows. Yeah, because what I think makes the shrinking/moving of the partitions take so long is because they are not empty (am I wrong?).

  Read the article

• Mount linux partition as Windows network share over internet

  - by CptEO

  I have a Linux server running RHEL 6. I have two Windows servers. All servers are connected directly to the web with an external IP, they are not in a local lan. What I would like to achieve is to setup the Linux server so that it offers a single share (the whole partition) that can be mounted as network drive within Windows. I don't want to use any 3rd party software to access the linux server because I want to use the linux server as a backup for Bare Metal Restore. In order to do so, I need to be able to access the linux partition from within the Windows Recovery Enviroment where I cannot install any 3rd party software. The linux server should only be accessible from given IP addresses (e.g. the 2 windows servers). Does anyone know if the setup I would like to have is possible?

  Read the article

• How do I configure a swap partition using swapspace

  - by jcalfee314

  I finally have the swapspace project installed and running (via init.d). The purpose is to have a dynamically re-sizing swap partition. I'm clueless however on how to use it. It has good documentation but just does not go into that last step. How to I configure a swap partition using swapspace? The process is probably the same for any 3rd party program that would provide a swap space implementation to the kernel. I know this was intended to run as a process because the project provides an init.d script.

  Read the article

• Installing windows 8 into a new partition

  - by ACarter

  I've just gone through the Windows 8 upgrade process, and I am at the "Install now/Install by creating media/Install later from your desktop" stage. I've already got a sufficiantly big, empty partition, so can someone explain in fairly simple terms how to install onto the new partition? I would prefer not to burn the ISO onto a disk, it would be a lot easier if I could use a USB drive. (I've done quite a bit of googling, but all that I can find goes into endless detain about the partitioning, and spends very little time on putting the ISO on a booteable drive. How do I do this? Do I need to empty the drive? etc?)

  Read the article

• Why can't I extend the C: drive on Vista? Because I have Free Space to its right instead of Unalloca

  - by tzup

  Okay this is annoying! I have a C: drive that is the primary partition (bootable) that I would like to extend. In order to do that it seems like I need to have Unallocated Space to the right of the partition. Right now, I have "Free Space" to the right. How in the world do I make it Unallocated (not formatted)? There must be some command line utility to be able to do this. Please help!

  Read the article

• I tried installing Ubuntu 10.04 and I got this message - any ideas on what to do?

  - by user41926

  No root file system defined. Please correct this from the partition menu. This message shows up when I first boot into Ubuntu after the installation. I installed it by mounting the ISO with Daemon Tools, and I just did the default Wubi installation. I keep reading everywhere that I need to choose my installation directory, but I don't get any option to do that. These are all the options I get for installation directory. I have a C and D partition on my drive, and I tried installing it on both and no luck either way. Any ideas?

  Read the article

• Can't recover hard drive

  - by BreezyChick89

  My drive got corrupt after a thunderstorm. It used to be 1 partition of 2.5tb but now it shows 2 partitions. It's weird because 300gig free space is about how much it had before corrupting, but it was part of the first partition. I tried $ sudo resize2fs -f /dev/sdb1 Resizing the filesystem on /dev/sdb1 to 536870911 (4k) blocks. resize2fs: Can't read an block bitmap while trying to resize /dev/sdb1 Please run 'e2fsck -fy /dev/sdb1' to fix the filesystem after the aborted resize operation. sudo e2fsck -f /dev/sdb1 e2fsck 1.42 (29-Nov-2011) The filesystem size (according to the superblock) is 610471680 blocks The physical size of the device is 536870911 blocks Either the superblock or the partition table is likely to be corrupt! Abort? n .... Error reading block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes Force rewrite<y>? yes Error writing block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes ... A lot of these. I can't use e2fsck -y because the first question aborts if I say "y". If I put a weight on the 'y' key it fails because none of the errors were really fixed. I asked this question before and tried using gparted but gparted fails because the first thing it does is: e2fsck -f -y -v /dev/sdb1 giving the same error. The disk status says healthy. There are no bad blocks. This is very frustrating because I can see the data in testdisk and it looks like it's all there. I already bought another 2.5tb drive and made a clone using dd. The next step if I can't fix this is to wipe that drive and just move the data with testdisk, but it seems certain folders will copy infinitely until the drive is full because of symlinks or errors so it's also a difficult option. sudo fdisk -l Disk /dev/sdb: 2500.5 GB, 2500495958016 bytes 255 heads, 63 sectors/track, 304001 cylinders, total 4883781168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005da5e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 4294969342 2147483647+ 83 Linux sudo badblocks -b 4096 -n -o badfile /dev/sdb 610471680 536870911 badfile is empty I also tried changing the superblock with "fsck -b" but all of them are the same.

  Read the article

• Virtualbox: Raw linux partition not booting

  - by abalter

  I have a dual-boot laptop with Windows 7 and Ubuntu 12.04. I am trying to boot the ubuntu partition from windows using Virtualbox. I have successfully created the .vmdk, and created the virtual machine. However, I can't get it to boot (in Virtualbox). All I get is a black screen with the cursor in the top left. I wonder if I'm specifying the partitions correctly. My Ubuntu install has 3 partitions: \, \boot, \home. No swap partition. These are all in Disk 0, partitions 3,4,5 respectively. The command I used to create the .vmdk is: VBoxManage internalcommands createrawvmdk -filename C:\Users\abalter\.virtualbox\ubuntu.vmdk -rawdisk \\.\PhysicalDrive0 -partitions 3,4,5 Then I create a virtual machine based on that .vmdk. Why won't it boot?

  Read the article

• windows 7 partition disappeared

  - by atoMerz

  I have a VPCF2 with windows 7 installed on it. I was working on my computer when on of my drives (D) disappeared. I can see it in Computer Management>Disk Management and it'd marked as Healthy(Primary Partition). When I right click on it the only options that are enabled are Delete Volume and Help. So I cannot assign a drive letter to it (not even in safe mode). I tried System Restore and it failed. I tried to boot the system using ubuntu tha was installed on my system but that fails too because it was installed on partition D. I'm hopeless. What can I do?

  Read the article

• How to I configure a swap partition using swapspace

  - by jcalfee314

  I finally have the swapspace project installed and running (via init.d). The purpose is to have a dynamically re-sizing swap partition. I'm clueless however on how to use it. It has good documentation but just does not go into that last step. How to I configure a swap partition using swapspace? The process is probably the same for any 3rd party program that would provide a swap space implementation to the kernel. I know this was intended to run as a process because the project provides an init.d script.

  Read the article

• Why is my dual-boot Ubuntu partition showing up as a peripheral "root.disk"?

  - by Don

  I recently installed Ubuntu 12.04, which I had been booting from a usb key, as a dual-boot on my machine running Windows 7. From what I had read online while researching, I was prepared to have to shrink the Windows partition and all that. But I never had to - it really was just a few clicks here and there and it was installed. I'm still pretty confused about it, but whatever, it worked, and the two peacefully coexist on my machine, and I have broken things to fix before I worry about fixing unbroken things. So yesterday I got it in my head to look at my partitions (I was considering making an all new partition to install the Windows 8 Release Preview). What I saw confused me. Here's a screenshot of the disk utility. At this moment, there is nothing connected to my computer, and nothing in any of the optical drives/ports/card readers/etc. Can you help me figure out what's going on here? Don's Machine is, I believe, my Windows partition - that's the name I assigned my machine from Windows Explorer. PQSERVICE is from what I can find online also Windows, but having to do with backup. And SYSTEM REQUIRED, if I browse it in Ubuntu, is definitely something to do with booting, and I believe it is also Windows'. According to the sizes shown, those three together should use up my 500 GB HD. Then further down, as a "peripheral device", it lists that 31 GB disk. This is obviously my Ubuntu (Model:Linux Loop:root.disk), but why is it showing up as a peripheral? So, to sum up those questions and to add some more random ones I had: Why is Ubuntu showing up as a peripheral device? If the Windows sections take up all 500 GB, where does Ubuntu live? If I renamed the disk partitions, would my life become a nightmare (seriously - can I safely rename them)? Why didn't I have to resize the Windows partition in the first place? Would giving Ubuntu more space improve its performance (it hangs alot)? Is it possible to have a partition for each OS (Windows 7 & 8, Ubuntu), a partition for files, and a separate partition for backups? Is this towards the good or bad idea end of the spectrum? @Elfy, would that explain why it keeps hanging? I guess I'll backup my files, rip it out, and reinstall it correctly later on today.

  Read the article

• How to convert ext3 partition to use encrypted file system without loosing data?

  - by User1

  My embedded Linux device have 2 partitions: small root partition containing OS. big data partition which uses ext3 I want to encrypt the data partition by using encrypted file system. I don't want loose any data of the partition. Size of the root partition is too small to hold all data of the data partition. It is not possible to use any external data storage. Is there any tools that can convert filesystem of the data partition from ext3 to encrypted fs without copying all files to other place?

  Read the article

• How to install Win7 over top of WinXP partition?

  - by Zeno

  I have a 2TB hard drive with 2 partitions on it, one a C drive for WinXP and another for extra space. I have a Win7 Pro install DVD and I have formatted that C drive via the DVD; it is now a blank "Primary" partition. I attempted to go through the Win7 setup and install it on that partition, but it's giving me an error: Setup unable to create new system partition or locate existing system partition. See setup log files for more info Googling around leads me to believe the entire drive has to be "cleaned" (diskpart) but that would wipe the entire other non-OS partition and I need to keep that data. How can I install Win7 on this blank partition without losing data on the other partition?

  Read the article

< Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >