Search Results

Search found 1553 results on 63 pages for 'tail recursion'.

Page 48/63 | < Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >

• LDOMs in Solaris 11 don't work

  - by Giovanni

  I just got a new Sun Fire T2000, installed Solaris 11 and was going to configure LDOMs. However "ldmd" can't be started and in turn ldm doesn't work. root@solaris11:~# ldm Failed to connect to logical domain manager: Connection refused root@solaris11:~# svcadm enable svc:/ldoms/ldmd:default root@solaris11:~# tail /var/svc/log/ldoms-ldmd\:default.log [ May 28 12:56:22 Enabled. ] [ May 28 12:56:22 Executing start method ("/opt/SUNWldm/bin/ldmd_start"). ] Disabling service because this domain is not a control domain [ May 28 12:56:22 Method "start" exited with status 0. ] [ May 28 12:56:22 Stopping because service disabled. ] [ May 28 12:56:22 Executing stop method (:kill). ] Why is this not a control domain? There is no other domain on the box (as far as I can tell). I have upgraded the firmware to the latest 6.7.12, booted with reset_nvram, nothing helped ... sc> showhost Sun-Fire-T2000 System Firmware 6.7.12 2011/07/06 20:03 Host flash versions: OBP 4.30.4.d 2011/07/06 14:29 Hypervisor 1.7.3.c 2010/07/09 15:14 POST 4.30.4.b 2010/07/09 14:24 What else should I do? Thanks!

  Read the article

• Linux e1000e (Intel networking driver) problems galore, where do I start?

  - by Evan Carroll

  I'm currently having a major problem with e1000e (not working at all) in Ubuntu Maverick (1.0.2-k4), after resume I'm getting a lot of stuff in dmesg: [ 9085.820197] e1000e 0000:02:00.0: PCI INT A disabled [ 9089.907756] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4 [ 9089.907762] e1000e: Copyright (c) 1999 - 2009 Intel Corporation. [ 9089.907797] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9089.907827] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9089.907857] e1000e 0000:02:00.0: setting latency timer to 64 [ 9089.908529] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9089.908922] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9089.908954] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9090.024625] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9090.024630] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9090.024712] e1000e 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005302-003 [ 9090.109492] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9090.164219] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X and, a bunch of [ 2128.005447] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 2128.005452] TDH <89> [ 2128.005454] TDT <27> [ 2128.005456] next_to_use <27> [ 2128.005458] next_to_clean <88> [ 2128.005460] buffer_info[next_to_clean]: [ 2128.005463] time_stamp <6e608> [ 2128.005465] next_to_watch <8a> [ 2128.005467] jiffies <6f929> [ 2128.005469] next_to_watch.status <0> [ 2128.005471] MAC Status <80080703> [ 2128.005473] PHY Status <796d> [ 2128.005475] PHY 1000BASE-T Status <4000> [ 2128.005477] PHY Extended Status <3000> [ 2128.005480] PCI Status <10> I decided to compile the latest stable e1000e to 1.2.17, now I'm getting: [ 9895.678050] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.17-NAPI [ 9895.678055] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9895.678098] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9895.678129] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9895.678162] e1000e 0000:02:00.0: setting latency timer to 64 [ 9895.679136] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.679160] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9895.679192] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9895.791758] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9895.791766] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9895.791850] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9895.892464] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.948175] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.949111] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9895.954694] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9895.954703] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9895.955157] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9906.832056] eth0: no IPv6 routers present With 1.2.20 I get: [ 9711.525465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-NAPI [ 9711.525472] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9711.525521] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9711.525554] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9711.525586] e1000e 0000:02:00.0: setting latency timer to 64 [ 9711.526460] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9711.526487] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9711.526523] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9711.639763] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9711.639771] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9711.639854] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9712.060770] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.116195] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.117098] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9712.122684] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 9712.122693] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9712.123142] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9722.920014] eth0: no IPv6 routers present But, I'm still getting these [ 9982.992851] PCI Status <10> [ 9984.993602] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 9984.993606] TDH <5d> [ 9984.993608] TDT <6b> [ 9984.993611] next_to_use <6b> [ 9984.993613] next_to_clean <5b> [ 9984.993615] buffer_info[next_to_clean]: [ 9984.993617] time_stamp <24da80> [ 9984.993619] next_to_watch <5d> [ 9984.993621] jiffies <24f200> [ 9984.993624] next_to_watch.status <0> [ 9984.993626] MAC Status <80080703> [ 9984.993628] PHY Status <796d> [ 9984.993630] PHY 1000BASE-T Status <4000> [ 9984.993632] PHY Extended Status <3000> [ 9984.993635] PCI Status <10> [ 9986.001047] e1000e 0000:02:00.0: eth0: Reset adapter [ 9986.176202] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9986.176211] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO I'm not sure where to start troubleshooting this. Any ideas? Here is the result of ethtool -d eth0 MAC Registers ------------- 0x00000: CTRL (Device control register) 0x18100248 Endian mode (buffers): little Link reset: reset Set link up: 1 Invert Loss-Of-Signal: no Receive flow control: enabled Transmit flow control: enabled VLAN mode: disabled Auto speed detect: disabled Speed select: 1000Mb/s Force speed: no Force duplex: no 0x00008: STATUS (Device status register) 0x80080703 Duplex: full Link up: link config TBI mode: disabled Link speed: 10Mb/s Bus type: PCI Express Port number: 0 0x00100: RCTL (Receive control register) 0x04048002 Receiver: enabled Store bad packets: disabled Unicast promiscuous: disabled Multicast promiscuous: disabled Long packet: disabled Descriptor minimum threshold size: 1/2 Broadcast accept mode: accept VLAN filter: enabled Canonical form indicator: disabled Discard pause frames: filtered Pass MAC control frames: don't pass Receive buffer size: 2048 0x02808: RDLEN (Receive desc length) 0x00001000 0x02810: RDH (Receive desc head) 0x00000001 0x02818: RDT (Receive desc tail) 0x000000F0 0x02820: RDTR (Receive delay timer) 0x00000000 0x00400: TCTL (Transmit ctrl register) 0x3103F0FA Transmitter: enabled Pad short packets: enabled Software XOFF Transmission: disabled Re-transmit on late collision: enabled 0x03808: TDLEN (Transmit desc length) 0x00001000 0x03810: TDH (Transmit desc head) 0x00000000 0x03818: TDT (Transmit desc tail) 0x00000000 0x03820: TIDV (Transmit delay timer) 0x00000008 PHY type: IGP2 and ethtool -c eth0 Coalesce parameters for eth0: Adaptive RX: off TX: off stats-block-usecs: 0 sample-interval: 0 pkt-rate-low: 0 pkt-rate-high: 0 rx-usecs: 3 rx-frames: 0 rx-usecs-irq: 0 rx-frames-irq: 0 tx-usecs: 0 tx-frames: 0 tx-usecs-irq: 0 tx-frames-irq: 0 rx-usecs-low: 0 rx-frame-low: 0 tx-usecs-low: 0 tx-frame-low: 0 rx-usecs-high: 0 rx-frame-high: 0 tx-usecs-high: 0 tx-frame-high: 0 Here is also the lspci -vvv for this controller 02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller Subsystem: Lenovo ThinkPad X60s Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0300c Data: 415a Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Device Serial Number 00-0a-e4-ff-ff-3e-ce-74 Kernel driver in use: e1000e Kernel modules: e1000e I filed a bug on this upstream, still no idea how to get more useful information. Here is a the result of the running that script EEPROM FIX UPDATE $ sudo bash fixeep-82573-dspd.sh eth0 eth0: is a "82573L Gigabit Ethernet Controller" This fixup is applicable to your hardware Your eeprom is up to date, no changes were made Do I still need to do anything? Also here is my EEPROM dump $ sudo ethtool -e eth0 Offset Values ------ ------ 0x0000 00 0a e4 3e ce 74 30 0b b2 ff 51 00 ff ff ff ff 0x0010 53 00 03 02 6b 02 7e 20 aa 17 9a 10 86 80 df 80 0x0020 00 00 00 20 54 7e 00 00 14 00 da 00 04 00 00 27 0x0030 c9 6c 50 31 3e 07 0b 04 8b 29 00 00 00 f0 02 0f 0x0040 08 10 00 00 04 0f ff 7f 01 4d ff ff ff ff ff ff 0x0050 14 00 1d 00 14 00 1d 00 af aa 1e 00 00 00 1d 00 0x0060 00 01 00 40 1f 12 07 40 ff ff ff ff ff ff ff ff 0x0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff 4a e0 I'd also like to note that I used eth0 every day for years and until recently never had an issue.

  Read the article

• What kind of “sysadmin stuff” should I show to students during a talk?

  - by Gregory Eric Sanderaon

  A teacher asked me If I could talk about my job as a linux sysadmin in his class. The course is called "Introduction to Operating systems" and i've been given 45 minutes to talk. The students are beginning their second year, so they've had a bit of experience with programming in different languages. What i'm like to do is show a series of hands-on examples of the kinds of things I do on a regular basis. I've already got a few ideas jotted down, but I'm afraid that they might be either too advanced or too simple for the students to appreciate. Another concern is that a topic might be too long to explain and use too much time overall. Here are a few ideas : Program deployment using version control (git in my case) filtering apache logs using grep, awk, uniq, tail A couple of bash scripts that i've made for various stuff on servers live montitoring (htop, iotop, iptraf) creating databases and assigning roles in mysql/postgresql So, are these ideas any good ? Do you have better ideas ? are the ideas too simple and should I go for more "advanced" stuff ?

  Read the article

• How can I capture output from LFTP? (Output not written to STDOUT or STDERR?)

  - by jondahl

  I would like get access to progress information from lftp. Currently, I'm using curl like so: curl http://example.com/file -o file -L 2> download.log This writes curl's progress information to the download.log file, which I can tail to get real-time progress. But the same approach doesn't work with lftp, either with stdout or stderr. I end up with an empty download.log file, until the transfer is complete. lftp -e 'get http://example.com/file;quit' 2> download.log lftp -e 'get http://example.com/file;quit' 1> download.log When I don't redirect output, I see progress on the screen. When I do redirect output, I stop seeing progress on the screen, but nothing shows up in download.log. After the file transfer is complete, I see the final result, like this - but nothing before: 97618627 bytes transferred in 104 seconds (913.1K/s) Is lftp doing something unusual with its output - printing to screen without printing to stdout/stderr? Are there other ways of capturing screen output than redirecting stdout/stderr?

  Read the article

• mercurial hgwebdir error with basicauth in apache2

  - by Dio

  Hello, I'm having kind of a strange error that I'm trying to track down. I was trying to setup mercurial on my home server this weekend. I seem to have it running up to the point where I'm trying to get repositories published correctly. I'm running Ubuntu 10.04 LTS Mercurial Distributed SCM (version 1.4.3) I followed the hgwebdir guide: http://mercurial.selenic.com/wiki/HgWebDirStepByStep and everything seems to work great, I can pull and push my local repositories. Then I tried to add basic auth changing ScriptAliasMatch ^/hg(.*) /var/hg/hgwebdir.cgi$1 <Directory "/var/hg"> Options ExecCGI FollowSymLinks AllowOverride None </Directory> to ScriptAliasMatch ^/hg(.*) /var/hg/hgwebdir.cgi$1 <Directory "/var/hg"> Options ExecCGI FollowSymLinks AllowOverride None AuthType Basic AuthName hgwebdir AuthUserFile /usr/local/etc/httpd/users Require valid-user </Directory> This works exactly as I'd expect it to when I navigate to the directory via my web browser, but when I hg push get a long section repeating of File "/usr/lib/python2.6/urllib2.py", line 369, in _call_chain result = func(*args) File "/usr/lib/python2.6/urllib2.py", line 855, in http_error_401 url, req, headers) File "/usr/lib/python2.6/urllib2.py", line 833, in http_error_auth_reqed return self.retry_http_basic_auth(host, req, realm) File "/usr/lib/python2.6/urllib2.py", line 843, in retry_http_basic_auth return self.parent.open(req, timeout=req.timeout) followed by File "/usr/lib/pymodules/python2.6/mercurial/keepalive.py", line 249, in do_open self._start_transaction(h, req) File "/usr/lib/pymodules/python2.6/mercurial/url.py", line 419, in _start_transaction return keepalive.HTTPHandler._start_transaction(self, h, req) File "/usr/lib/pymodules/python2.6/mercurial/keepalive.py", line 342, in _start_transaction h.endheaders() File "/usr/lib/python2.6/httplib.py", line 904, in endheaders self._send_output() File "/usr/lib/python2.6/httplib.py", line 776, in _send_output self.send(msg) File "/usr/lib/pymodules/python2.6/mercurial/url.py", line 247, in _sendfile connection.send(self, data) File "/usr/lib/pymodules/python2.6/mercurial/keepalive.py", line 519, in safesend self.connect() File "/usr/lib/pymodules/python2.6/mercurial/url.py", line 273, in connect keepalive.HTTPConnection.connect(self) RuntimeError: maximum recursion depth exceeded while calling a Python object I'm a bit at a loss on this one. I'm really not sure why adding the authorization seems to work fine via my web browser but throw these errors from hg. Any help would be greatly appreciated.

  Read the article

• Mysql: Disk is full writing

  - by elma

  Hi there, I'm having some problems with my mysql server lately, so I've decided to check the error logs: [root@LSN-D1179 log]# tail -10 mysqld.log 100325 19:30:03 [ERROR] /usr/libexec/mysqld: Table './lfe/actions' is marked as crashed and should be repaired 100325 19:30:03 [ERROR] /usr/libexec/mysqld: Table './lfe/actions' is marked as crashed and should be repaired 100325 19:30:18 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_task_logs.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:34:34 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_profile_portal_views.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:39:46 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_posts.TMD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:40:18 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_task_logs.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:44:34 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_profile_portal_views.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:49:46 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_posts.TMD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:50:18 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_task_logs.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:54:34 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_profile_portal_views.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs And here's is my df -h output [root@LSN-D1179 log]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 143G 6.2G 129G 5% / /dev/sda1 99M 12M 83M 13% /boot tmpfs 490M 0 490M 0% /dev/shm As you can see, I have plenty of free space; so I couldn't figure out these "Disk is full" errors in mysqld.log. Does anyone know what should I do to fix this? Ugur

  Read the article

• NFS: Server says "authenticated mount request", but client sees "access denied"

  - by zigdon

  I have two machine, an NFS server (RHEL) and a client (Debian). The server has NFS set up, exporting a particular directory: server:~$ sudo /usr/sbin/rpcinfo -p localhost program vers proto port 100000 2 tcp 111 portmapper 100000 2 udp 111 portmapper 100024 1 udp 910 status 100024 1 tcp 913 status 100021 1 udp 53391 nlockmgr 100021 3 udp 53391 nlockmgr 100021 4 udp 53391 nlockmgr 100021 1 tcp 32774 nlockmgr 100021 3 tcp 32774 nlockmgr 100021 4 tcp 32774 nlockmgr 100007 2 udp 830 ypbind 100007 1 udp 830 ypbind 100007 2 tcp 833 ypbind 100007 1 tcp 833 ypbind 100011 1 udp 999 rquotad 100011 2 udp 999 rquotad 100011 1 tcp 1002 rquotad 100011 2 tcp 1002 rquotad 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 100003 4 udp 2049 nfs 100003 2 tcp 2049 nfs 100003 3 tcp 2049 nfs 100003 4 tcp 2049 nfs 100005 1 udp 1013 mountd 100005 1 tcp 1016 mountd 100005 2 udp 1013 mountd 100005 2 tcp 1016 mountd 100005 3 udp 1013 mountd 100005 3 tcp 1016 mountd server$ cat /etc/exports /dir *.my.domain.com(ro) client$ grep dir /etc/fstab server.my.domain.com:/dir /dir nfs tcp,soft,bg,noauto,ro 0 0 All seems well, but when I try to mount, I see the following: client$ sudo mount /dir mount.nfs: access denied by server while mounting server.my.domain.com:/dir And on the server I see: server$ tail /var/log/messages Mar 15 13:46:23 server mountd[413]: authenticated mount request from client.my.domain.com:723 for /dir (/dir) What am I missing here? How should I be debugging this?

  Read the article

• Outgrew MongoDB … now what?

  - by samsmith

  We dump debug and transaction logs into mongodb. We really like mongodb because: Blazing insert perf document oriented Ability to let the engine drop inserts when needed for performance But there is this big problem with mongodb: The index must fit in physical RAM. In practice, this limits us to 80-150gb of raw data (we currently run on a system with 16gb RAM). Sooooo, for us to have 500gb or a tb of data, we would need 50gb or 80gb of RAM. Yes, I know this is possible. We can add servers and use mongo sharding. We can buy a special server box that can take 100 or 200 gb of RAM, but this is the tail wagging the dog! We could spend boucoup $$$ on hardware to run FOSS, when SQL Server Express can handle WAY more data on WAY less hardware than Mongo (SQL Server does not meet our architectural desires, or we would use it!) We are not going to spend huge $ on hardware here, because it is necessary only because of the Mongo architecture, not because of the inherent processing/storage needs. (And sharding? Please! Cost aside, who needs the ongoing complexity of three, five, or more servers to manage a relatively small load?) Bottom line: MongoDB is FOSS, but we gotta spend $$$$$$$ on hardware to run it? We sould rather buy commercial SW! I am sure we are not the first to hit this issue, so we ask the community: Where do we go next? (We already run Mongo v2) Thanks!!

  Read the article

• Tomcat 7 on Ubuntu 12.04 startup issues

  - by Nico Huysamen

  I am having trouble getting tomcat 7 to start up on my new VPS. I am really scratching my head since I have done this often. So I'm thinking it might be the VPS. I just got a new VPS from CINFU. After a clean install of Ubuntu 12.04 32bit, I install openjdk-6-jdk, update JAVA_HOME to point to: /usr/lib/jvm/java-1.6.0-openjdk-i386 and JRE_HOME to: /usr/lib/jvm/java-1.6.0-openjdk-i386/jre But when I try to run: ./catalina.sh run it simply outputs: Using CATALINA_BASE: /opt/tomcat/apache-tomcat-7.0.29 Using CATALINA_HOME: /opt/tomcat/apache-tomcat-7.0.29 Using CATALINA_TMPDIR: /opt/tomcat/apache-tomcat-7.0.29/temp Using JRE_HOME: /usr/lib/jvm/java-1.6.0-openjdk-i386 Using CLASSPATH: /opt/tomcat/apache-tomcat-7.0.29/bin/bootstrap.jar:/opt/tomcat/apache-tomcat-7.0.29/bin/tomcat-juli.jar and stops. It just hangs there doing nothing. If I run ./startup.sh && tail -f ../logs/catalina.out it gets to: Aug 24, 2012 8:38:36 PM org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["http-bio-8080"] Aug 24, 2012 8:38:36 PM org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["ajp-bio-8009"] Aug 24, 2012 8:38:36 PM org.apache.catalina.startup.Catalina load INFO: Initialization processed in 495 ms Aug 24, 2012 8:38:36 PM org.apache.catalina.core.StandardService startInternal INFO: Starting service Catalina Aug 24, 2012 8:38:36 PM org.apache.catalina.core.StandardEngine startInternal INFO: Starting Servlet Engine: Apache Tomcat/7.0.29 but I am unable to access anything. The request just hangs. I have also tried a few other things like explicitly exporting the paths etc in catalina.sh, and running ./startup.sh rather than catalina.sh, but the furthest I have gotten is that it finishes deploying all the WARs (the default ones that comes with tomcat like the host-manager etc), but then it hangs: Aug 24, 2012 8:47:30 PM org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["http-bio-8080"] and does nothing. Anyone have any pointers that might help? As I said, I must really be missing something stupid since this has worked on all other VPSs that we have. UPDATE I figured out that the problem is actually the fact that they use OpnVZ virtualization and that there are known compatibility problems with Java.

  Read the article

• Apache mod-pagespeed installation affects mod-spdy?

  - by tim peterson

  Recently my site (an https connection, running on an Amazon EC2 ubuntu apache2.2) has this issue where I need to load the page several times (3-4) before it will load normally without issue. It will then load normally as long as I keep loading pages regularly (every couple seconds). It will stall again if I don't load pages for a few minutes. It has nothing to do with my application because I don't have this problem with the exact same app codebase on my Apache installation on my laptop. The only things to my knowledge that I've changed is that I recently installed mod_spdy and then a few weeks later I installed mod_pagespeed, https://developers.google.com/speed/pagespeed/mod. However, I have since turned mod_pagespeed off by setting its pagespeed.conf to mod_pagespeed off. Unfortunately, that didn't solve the problem. The line below is how every of last 10 lines of my error.log look: # tail -f /var/log/apache2/error.log ... [32728:32729:ERROR:mod_spdy.cc(162)] request->chunked == 1 in request GET / HTTP/1.1 [Sat Jun 02 04:50:08 2012] [warn] [client 50.136.93.153] [stream 5] [32728:32729:WARNING:http_to_spdy_filter.cc(113)] HttpToSpdyFilter is not the last filter in the chain: chunk any thoughts? thank you, tim

  Read the article

• PPTP Client setup, Fedora 17

  - by Suarez Romina

  I am trying to connect to hidemyass.com VPN services via PPTP, but I am having issues understanding why it isn't working, since I don't get a warning or fatal error and my IP remains the same. This is how i create the connection: [root@lasvegas-nv-datacenter ~]# pptpsetup --create TUNNELNAME --server 199.58.165.20 --username MYUSERNAME --password MYPASSWORD --encrypt --start And this is the output: Using interface ppp0 Connect: ppp0 <-- /dev/pts/1 CHAP authentication succeeded MPPE 128-bit stateless compression enabled local IP address 10.200.21.14 remote IP address 10.200.20.1 After that, I check the log and this is what i get: [root@lasvegas-nv-datacenter ~]# tail -f /var/log/messages Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_rep:pptp_ctrl.c:254]: Sent control packet type is 1 'Start-Control-Connection-Request' Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:754]: Received Start Control Connection Reply Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:788]: Client connection established. Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_rep:pptp_ctrl.c:254]: Sent control packet type is 7 'Outgoing-Call-Request' Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:873]: Received Outgoing Call Reply. Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:912]: Outgoing call established (call ID 0, peer's call ID 20096). Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: CHAP authentication succeeded Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: MPPE 128-bit stateless compression enabled Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: local IP address 10.200.21.14 Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: remote IP address 10.200.20.1 Can someone help me? Basically, i Ieed to connect to the VPN and have my IP changed after the connection. I read a lot of guides but still cannot understand why I don't get a connection.

  Read the article

• Can't start Bind9 on Ubuntu 10.04 + Plesk 10.1 - "named: no process found"

  - by bradley.ayers

  I've installed a fresh version of Ubuntu 10.04 64bit, I didn't install bind when choosing what packages should be installed in the Ubuntu installer. I downloaded the auto installer for Plesk 10.1 and installed it successfully. When I logged into the Plesk control panel and tried to change the password, it failed because it couldn't restart bind. I SSH'd into the box and tried a sudo /etc/init.d/bind9 restart and get the following: brad@ws01:/root# sudo /etc/init.d/bind9 restart * Stopping domain name service... bind9 WARNING: key file (/etc/bind/rndc.key) exists, but using default configuration file (/etc/bind/rndc.conf) rndc: connect failed: 127.0.0.1#953: connection refused named: no process found [ OK ] * Starting domain name service... bind9 [fail] Looking at tail /var/log/messages reveals a whole bunch of: Feb 23 16:08:21 ws01 kernel: [ 3840.065851] type=1503 audit(1298441301.831:31): operation="open" pid=5565 parent=5563 profile="/usr/sbin/named" requested_mask="::r" denied_mask="::r" fsuid=108 ouid=0 name="/var/named/run-root/etc/named.conf" Edit: After following ooshro's advice, bind runs, however I still get the named: no process found error: brad@ws01:/etc/apparmor.d$ sudo /etc/init.d/bind9 restart * Stopping domain name service... bind9 WARNING: key file (/etc/bind/rndc.key) exists, but using default configuration file (/etc/bind/rndc.conf) named: no process found [ OK ] * Starting domain name service... bind9 [ OK ]

  Read the article

• r1soft agent is failing with the error: "write error while sending code: Broken pipe"

  - by curiousguy

  I have an Ubuntu 10.04.4 LTS server with r1soft agent installed in it. Recently, the backups are failing with the following error. -------- write error while sending code: Broken pipe -------- I have reinstalled the buagent but to no avail. On checking the server logs, I could see the following errors listed in it: -------- # tail -f /var/log/messages |grep -i buagent Nov 17 03:35:06 microscope buagent: Need to back up 126 sectors Nov 17 03:35:06 microscope buagent: (Righteous Backup Linux Agent) 1.79.0 build 12433 Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.195) with valid RSA key Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.201) with valid RSA key Nov 17 03:35:06 microscope buagent: sending auth challenge for allowed host at (10.128.136.201) port (47890) Nov 17 03:35:06 microscope buagent: host (10.128.136.201) port (47890) authentication successful Nov 17 03:35:06 microscope buagent: Backup request accepted. Starting backup. Nov 17 03:35:06 microscope buagent: Snapshot completed in 0.010 seconds. Nov 17 03:45:03 microscope buagent: Error reading blocks from snapshot. Nov 17 03:45:03 microscope buagent: Reading blocks failed Nov 17 03:45:03 microscope buagent: error backup aborted Nov 17 03:45:03 microscope buagent: backup failed on agent closing connection Nov 17 03:45:03 microscope buagent: Backup failed. Nov 17 03:45:03 microscope buagent: write error while sending code: Broken pipe (32) Nov 17 03:45:03 microscope buagent: tell child write failed -------- I tried changing the 'Timeout' and 'DiskAsPartition' value in '/etc/buagent/agent_config' file but no luck. Also, verified that proper route is added to the backup server. The agent is also running fine. Am I missing anything? Any help would be much appreciated. Note: CDP 2.0 is installed in the backup server.

  Read the article

• Getting an error when mounting LVM snapshot

  - by Sandra

  I have migrated a file based Xen guest to LVM using dd bs=1M if=/dev/zero of=/dev/vg00/vm10 qemu-img convert ~/vm10.qcow2 -O raw /dev/vg00/vm10 and changed the Xen domain file for the VM to use the LV instead of the old file. The VM boots up, and now on the Xen host would I like to make a snapshot of the running VM. # lvcreate --size 10G --snapshot --name vm10-snapshot /dev/vg00/vm10 Logical volume "vm10-snapshot" created # mount /dev/vg00/vm10-snapshot /mnt/snapshot/ mount: you must specify the filesystem type # dmesg |tail EXT3 FS on dm-3, internal journal EXT3-fs: mounted filesystem with ordered data mode. hfs: unable to find HFS+ superblock VFS: Can't find ext3 filesystem on dev dm-4. hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock VFS: Can't find ext3 filesystem on dev dm-2. hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock For some reason it can't see it is an EXT3 filesystem. I have also tried to mount with -t ext3, but still didn't mount. # lvdisplay --- Logical volume --- LV Name /dev/vg00/vm10 VG Name vg00 LV UUID I1y1vQ-Bac5-5jwW-melh-TY5h-l9NO-qaelKk LV Write Access read/write LV snapshot status source of /dev/vg00/vm10-snapshot [active] LV Status available # open 2 LV Size 8.00 GB Current LE 2048 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:2 --- Logical volume --- LV Name /dev/vg00/vm10-snapshot VG Name vg00 LV UUID GWsOx3-TPpr-GW64-uiMz-u1YN-QU4h-l0Kala LV Write Access read/write LV snapshot status active destination for /dev/vg00/vm10 LV Status available # open 0 LV Size 8.00 GB Current LE 2048 COW-table size 10.00 GB COW-table LE 2560 Allocated to snapshot 0.00% Snapshot chunk size 4.00 KB Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:4 # What could the problem be?

  Read the article

• Authenticate users with Zimbra LDAP Server from other CentOS clients

  - by efesaid

  I'am wondering that how can integrate my database,web,backup etc.. centos servers with Zimbra LDAP Server. Does it require more advanced configuration than standart ldap authentication ? My zimbra server version is [zimbra@zimbra ~]$ zmcontrol -v Release 8.0.5_GA_5839.RHEL6_64_20130910123908 RHEL6_64 FOSS edition. My LDAP Server status is [zimbra@ldap ~]$ zmcontrol status Host ldap.domain.com ldap Running snmp Running stats Running zmconfigd Running I already installed nss-pam-ldapd packages to my servers. [root@www]# rpm -qa | grep ldap nss-pam-ldapd-0.7.5-18.2.el6_4.x86_64 apr-util-ldap-1.3.9-3.el6_0.1.x86_64 pam_ldap-185-11.el6.x86_64 openldap-2.4.23-32.el6_4.1.x86_64 My /etc/nslcd.conf is [root@www]# tail -n 7 /etc/nslcd.conf uid nslcd gid ldap # This comment prevents repeated auto-migration of settings. uri ldap://ldap.domain.com base dc=domain,dc=com binddn uid=zimbra,cn=admins,cn=zimbra bindpw **pass** ssl no tls_cacertdir /etc/openldap/cacerts When i run [root@www ~]# id username id: username: No such user But i am sure that username user exist on ldap server. EDIT : When i run ldapsearch command i got all result with credentials and dn. [root@www ~]# ldapsearch -H ldap://ldap.domain.com:389 -w **pass** -D uid=zimbra,cn=admins,cn=zimbra -x 'objectclass=*' # extended LDIF # # LDAPv3 # base <dc=domain,dc=com> (default) with scope subtree # filter: objectclass=* # requesting: ALL # # domain.com dn: dc=domain,dc=com zimbraDomainType: local zimbraDomainStatus: active . . .

  Read the article

• SSH over HTTPS with proxytunnel and nginx

  - by Thermionix

  I'm trying to setup an ssh over https connection using nginx. I haven't found any working examples, so any help would be appreciated! ~$ cat .ssh/config Host example.net Hostname example.net ProtocolKeepAlives 30 DynamicForward 8118 ProxyCommand /usr/bin/proxytunnel -p ssh.example.net:443 -d localhost:22 -E -v -H "User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32)" ~$ ssh [email protected] Local proxy ssh.example.net resolves to 115.xxx.xxx.xxx Connected to ssh.example.net:443 (local proxy) Tunneling to localhost:22 (destination) Communication with local proxy: -> CONNECT localhost:22 HTTP/1.0 -> Proxy-Connection: Keep-Alive -> User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32) <- <html> <- <head><title>400 Bad Request</title></head> <- <body bgcolor="white"> <- <center><h1>400 Bad Request</h1></center> <- <hr><center>nginx/1.0.5</center> <- </body> <- </html> analyze_HTTP: readline failed: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host Nginx config on the server; ~$ cat /etc/nginx/sites-enabled/ssh upstream tunnel { server localhost:22; } server { listen 443; server_name ssh.example.net; location / { proxy_pass http://tunnel; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } ssl on; ssl_certificate /etc/ssl/certs/server.cer; ssl_certificate_key /etc/ssl/private/server.key; } ~$ tail /var/log/nginx/access.log 203.xxx.xxx.xxx - - [08/Feb/2012:15:17:39 +1100] "CONNECT localhost:22 HTTP/1.0" 400 173 "-" "-"

  Read the article

• WGet or cURL: Mirror Site from http://site.com And No Internal Access

  - by alharaka

  I have tried wget -m wget -r and a whole bunch of variations. I am getting some of the images on http://site.com, one of the scripts, and none of the CSS, even with the fscking -p parameter. The only HTML page is index.html and there are several more referenced, so I am at a loss. curlmirror.pl on the cURL developers website does not seem to get the job done either. Is there something I am missing? I have tried different levels of recursion with only this URL, but I get the feeling I am missing something. Long story short, some school allows its students to submit web projects, but they want to know how they can collect everything for the instructor who will grade it, instead of him going to all the externally hsoted sites. UPDATE: I think I figured out the issue. I though the links to the other pages were in the index.html page that downloaded. I was way off. Turns out the footer of the page, which has all the navigation links, is handled by a JavaScript file Include.js, which reads JLSSiteMap.js and some other JS files to do page navigation and the like. As a result, wget does not pick up an other dependencies because a lot of this crap is handled not on web pages. How can I handle such a website? This is one of several problem cases. I assume little can be done if wget cannot parse JavaScript.

  Read the article

• Ubuntu server PPTPD with OS X clients Problems

  - by Nakedsteve

  I'm trying to get a PPTP server running on a ubuntu server, but I've run into some issues with it. I followed this guide on how to set up pptpd on my server, and everything went smooth, but when I try to connect with my mac, it gives me this error: Here's my configuration: Does anyone have any idea as to what I'm doing wrong here? Update: Here's what the pptpd.log has to say about it: steve@debian:~$ sudo tail /var/log/pptpd.log sudo: unable to resolve host debian Sep 3 21:46:43 debian pptpd[2485]: MGR: Manager process started Sep 3 21:46:43 debian pptpd[2485]: MGR: Maximum of 11 connections available Sep 3 21:46:43 debian pptpd[2485]: MGR: Couldn't create host socket Sep 3 21:46:43 debian pptpd[2485]: createHostSocket: Address already in use Sep 3 21:46:56 debian pptpd[2486]: CTRL: Client 192.168.1.101 control connection started Sep 3 21:46:56 debian pptpd[2486]: CTRL: Starting call (launching pppd, opening GRE) Sep 3 21:46:56 debian pptpd[2486]: GRE: read(fd=6,buffer=204d0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Sep 3 21:46:56 debian pptpd[2486]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Sep 3 21:46:56 debian pptpd[2486]: CTRL: Reaping child PPP[2487] Sep 3 21:46:56 debian pptpd[2486]: CTRL: Client 192.168.1.101 control connection finished My pptpd options are: asyncmap 0 noauth crtscts lock hide-password modem debug proxyarp lcp-echo-interval 30 lcp-echo-failure 4 nopix

  Read the article

• Bash wonkyness on Ubuntu versus RHEL

  - by d34dh0r53

  Fellow faulters, I'm playing around with a one liner that I've developed on a RHEL 5.4 box and I have it working perfectly: TOTAL_RAM=`free | grep Mem: | awk '{ print $2 }'`; \ ps axo rss,comm,pid | awk -v total_ram=$TOTAL_RAM \ '{ proc_list[$2] += $1; } END { for (proc in proc_list) \ { proc_pct = (proc_list[proc]/total_ram)*100; printf("%d\t%s\t%0.2f%\n", proc_list[proc],proc,proc_pct); }}' \ | sort -n | tail -n 10 Which outputs something like the following on my RHEL box: 3736 logmon 0.01% 4156 EvMgrC 0.01% 4692 hald 0.01% 5020 ntpd 0.02% 6252 sshd 0.02% 7784 cvd 0.02% 9224 snmpd 0.03% 13068 dsm_sa_datamgr3 0.04% 23320 dsm_om_connsvc3 0.07% 4249864 mysqld 12.90% However on my Ubuntu 9.04 slice I get this: awk: run time error: not enough arguments passed to printf("%d %s %0.2f% ") FILENAME="-" FNR=104 NR=104 33248 console-kit-dae 3.17 I think it has to be bash that is borking something, but I'm really not doing anything that should be that bash specific. The RHEL box is running: # yum info bash | grep -e Version -e Release Version : 3.2 Release : 24.el5 And the Ubuntu box: # apt-cache show bash | grep -e Version Version: 3.2-5ubuntu1 I haven't dug into this super deeply, and thought I'd ping my fellow johnnys to see if you've ever run across this before. /bow

  Read the article

• Repairing inconsistent pages in database

  - by Raj

  We have a SQL 2000 DB. The server crashed due to Raid array failure. Now when we run DBCC CHECKDB, we get an error that there are 27 consistency errors in 9 pages. When we run DBCC PAGE on these pages, we get this: Msg 8939, Level 16, State 106, Line 1 Table error: Object ID 1397580017, index ID 2, page (1:8404521). Test (m_freeCnt == freeCnt) failed. Values are 2 and 19. Msg 8939, Level 16, State 108, Line 1 Table error: Object ID 1397580017, index ID 2, page (1:8404521). Test (emptySlotCnt == 0) failed. Values are 1 and 0. Since the indicated index is non-clustered and is created by a unique constarint that includes 2 columns, we tried dropping and recreating the index. This resulted in the following error: CREATE UNIQUE INDEX terminated because a duplicate key was found for index ID 2. Most significant primary key is '3280'. The statement has been terminated. However running Select var_id,result_on from tests group by var_id,result_on having count(*)>1 returns 0 rows. Here is what we are planning to do: Restore a pre-server crash copy of the DB and run DBCC CHECKDB If that returns clean, then restore again with no recovery Apply all subequent TLOG backups Stop production app, take a tail log backup and apply that too Drop prod DB and rename the freshly restored DB to make it prod Start prod app Could someone please punch holes in this approach? Maybe, suggest a different approach? What we need is minimum downtime. SQL 2000 DB Size 94 GB The table that has corrupt pages has 460 Million+ rows of data Thanks for the help. Raj

  Read the article

• How to restrict zone transfers to specific authorized servers only

  - by JonoB

  I recently failed a PCI compliance scan because of the following: This DNS server allows unrestricted zone transfers. Attackers may be able to use this information to gain knowledge on the structure of your networks to aid in device discovery prior to an actual attack. And the suggested solution is as follows: Reconfigure this DNS server to restrict zone transfers to specific authorized servers only. I am running a dedicated Linux Centos server. My understanding is that I have to edit the /etc/named.conf file, which I have done and the the relevant part is as follows: options { acl "trusted" { 127.0.0.1; xxx.xxx.xxx.001; //this is one of the server's ip's xxx.xxx.xxx.002; //this is another server's ip }; allow-recursion { trusted; }; allow-notify { trusted; }; allow-transfer { trusted; }; }; I then restarted the named service /etc/rc.d/init.d/named restart and requested a re-scan, which failed again for the same reason. Am I missing something obvious here?

  Read the article

• Samba between Ubuntu server 10.10 and Windows Vista, Windows 7

  - by chepukha

  Hi all, I have a linux box running Linux server ubuntu 10.10. I have installed Samba on this linux box and want to share files with my laptops which run Windows Vista home and Windows 7 home. I have been struggling with the setup for almost a month but couldn't get it right. If I try to access share folder from Windows Vista, I get message "Windows cannot access \\server_ip_address". Error code: 0x80070035. The network path was not found. If I access from Windows 7, then after entering password to login I can see the list of share folders on Linux box. But if I click on a share folder, I get the same error message as above. Tail /var/log/samba/log.windows7-pc I got the following message: [2011/03/16 00:17:41.427238, 0] smbd/service.c:988(make_connection_snum) canonicalize_connect_path failed for service sharemedia, path /root/sharemedia Here is my setting in smb.conf [global] share modes = yes netbios name = Samba workgroup = WORKGROUP wins support = yes encrypt passwords = true [sharemedia] comment = Tesing sharing using Samba path=/root/sharemedia/ public = yes valid users = samba_usr_name ; make sure all files are sensible permissions create mask = 0660 force create mask = 0660 directory mask = 2770 force directory mask = 2770 directory security mask = 0000 ; Normal share parameters read only = no browseable = yes writable = yes guest ok = no

  Read the article

• Is it possible to mount a disk image, created with dd, to a directory on a mounted external usb hdd?

  - by Keeper Hood

  I have an image of my home (/dev/sda3) partition, which I've created using the "dd" command. dd if=/dev/sda3 of=/path/to/disk.img I've deleted the home partition via gparted in order to enlarge my /dev/root partition. Then I've recreated the /dev/sda3 partition which is smaller in size then the one I've backed up to the image. I was wondering since I have a 2TB external HDD, could it be possible to mount my backed up image on the external HDD and then copy the files into the /home directory. Since the external HDD would be already in a "mounted state", I'm unsure whether this is a good idea, mounting on a mounted device. I'm running Slackware 13.37 (64bit). used ext4 on all the partitions. resized the root partition with gparted live cd. I've tried mount -t ext4 /path/to/disk.img /mng/image -o loop It gave me an fs error (wrong fs type, bad option, bad superblock on dev/loop/0) Then i did dmesg | tail which outputs: EXT4-fs (loop0) : bad geometry: block count 29009610 exceeds size of defice (1679229 blocks) I have no idea what to do, I want to restore my /home data from the image I've backed up.

  Read the article

• Web SMTP Server(foo.com) will not send mail to exchange server which is also(foo.com)

  - by Atom

  I think I understand this problem fully, but I do not know how to approach it or where to go in terms of troubleshooting. I've got my one domain http://foo.com that runs a Zen Cart installation that needs to be able to send emails to users(order confirmation, password reset). This works fine to send to any other domain BUT foo.com. I'm running a locally hosted exchange server that is foo.com, and we can send and receive email just fine. If I run tail -f /usr/local/psa/var/log/maillog I recieve this error: Apr 1 10:08:51 foo qmail-local-handlers[25824]: Handlers Filter before-local for qmail started ... Apr 1 10:08:51 foo qmail-local-handlers[25824]: from= Apr 1 10:08:51 foo qmail-local-handlers[25824]: [email protected] Apr 1 10:08:51 foo qmail-local-handlers[25824]: cannot reinject message to '[email protected]' Apr 1 10:08:51 foo qmail: 1270141731.583139 delivery 32410: failure: This_address_no_longer_accepts_mail./ Apr 1 10:08:51 foo qmail: 1270141731.584098 status: local 0/10 remote 0/20 I understand that the foo.com SMTP service doesn't have any account but the one that is used to authenticate mail being sent, so of course, I understand why it's saying 'this address no longer accepts mail'. My question is, how can I get the foo.com(web) SMTP service to handle emails meant for my exchange server([email protected]) or how do I handle the mail that needs to be sent to our exchange server? Is this something to do with MX records? Thanks in advance A

  Read the article

• Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

  - by develop7

  Preface: I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator tells "Logon failure" upon connect attempt. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

  Read the article

< Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >