Search Results

Search found 13669 results on 547 pages for 'left handed'.

Page 480/547 | < Previous Page | 476 477 478 479 480 481 482 483 484 485 486 487  | Next Page >

  • Volume group disappeared, LVs still available

    - by Ben
    I've run into an issue with my KVM host which runs VMs on a LVM volume. As of last night the logical volumes are no longer seen as such (I can't create snapshots of them even though I have been for months now). Running any scans all result in nothing being found: [root@apollo ~]# pvscan No matching physical volumes found [root@apollo ~]# vgscan Reading all physical volumes. This may take a while... No volume groups found root@apollo ~]# lvscan No volume groups found If I try restoring the VG conf backup from /etc/lvm/backups/vg0 I get the following error: [root@apollo ~]# vgcfgrestore -f /etc/lvm/backup/vg0 vg0 Couldn't find device with uuid 20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt. Cannot restore Volume Group vg0 with 1 PVs marked as missing. Restore failed. /etc/lvm/backups/vg0 has the following for the physical volume: physical_volumes { pv0 { id = "20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt" device = "/dev/sda5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 4292870143 # 1.99902 Terabytes pe_start = 384 pe_count = 524031 # 1.99902 Terabytes } } fdisk -l /dev/sda shows the following: [root@apollo ~]# fdisk -l /dev/sda Disk /dev/sda: 6000.1 GB, 6000069312512 bytes 64 heads, 32 sectors/track, 5722112 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000188b7 Device Boot Start End Blocks Id System /dev/sda1 2 32768 33553408 82 Linux swap / Solaris /dev/sda2 32769 33280 524288 83 Linux /dev/sda3 33281 1081856 1073741824 83 Linux /dev/sda4 1081857 3177984 2146435072 85 Linux extended /dev/sda5 1081857 3177984 2146435071+ 8e Linux LVM The server is running a 4 disk HW RAID10 which seems perfectly healthy according to megacli and smartd. The only odd message in /var/log/messages is the following which shows up every couple of hours: Jun 10 09:41:57 apollo udevd[527]: failed to create queue file: No space left on device Output of df -h [root@apollo ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 1016G 119G 847G 13% / /dev/sda2 508M 67M 416M 14% /boot Does anyone have any ideas what to do next? The VMs are all running fine at the moment apart from not being able to snapshot them. Updated with extra info It's not a lack of inodes: [root@apollo ~]# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda3 67108864 48066 67060798 1% / /dev/sda2 32768 47 32721 1% /boot pvs, vgs & lvs either output nothing or "No volume groups found".

    Read the article

  • Unable to commit file through svn, server sent truncated HTTP response body

    - by Rocket3G
    I have my own VPS, on which I want to run a simple SVN + chiliproject setup. I have re-installed SVN, CHILI and the OS several times, and it always works for a couple of hours/days and then it just stops working. Well, everything works, except I can't upload any files. Committing directories seems to work just fine, but when I try to commit a file it breaks. I have an error log file, which gives me the following text when I try to commit something x.x.x.x - - [19/Oct/2013:00:01:46 +0200] "OPTIONS /project HTTP/1.1" 200 149 x.x.x.x - - [19/Oct/2013:00:01:46 +0200] "PROPFIND /project HTTP/1.1" 207 346 x.x.x.x - - [19/Oct/2013:00:01:46 +0200] "MKACTIVITY /project/!svn/act/c11d45ac-86b6-184a-ac5a-9a1105d64563 HTTP/1.1" 401 345 x.x.x.x - admin [19/Oct/2013:00:01:46 +0200] "MKACTIVITY /project/!svn/act/c11d45ac-86b6-184a-ac5a-9a1105d64563 HTTP/1.1" 201 262 x.x.x.x - - [19/Oct/2013:00:01:46 +0200] "PROPFIND /project HTTP/1.1" 207 236 x.x.x.x - admin [19/Oct/2013:00:01:46 +0200] "CHECKOUT /project/!svn/vcc/default HTTP/1.1" 201 271 x.x.x.x - admin [19/Oct/2013:00:01:46 +0200] "PROPPATCH /project/!svn/wbl/c11d45ac-86b6-184a-ac5a-9a1105d64563/1 HTTP/1.1" 207 267 x.x.x.x - admin [19/Oct/2013:00:01:46 +0200] "CHECKOUT /project/!svn/ver/1 HTTP/1.1" 201 271 x.x.x.x - - [19/Oct/2013:00:01:46 +0200] "HEAD /project/index.html HTTP/1.1" 404 - x.x.x.x - admin [19/Oct/2013:00:01:46 +0200] "PUT /project/!svn/wrk/c11d45ac-86b6-184a-ac5a-9a1105d64563/index.html HTTP/1.1" 201 269 x.x.x.x - admin [19/Oct/2013:00:02:04 +0200] "DELETE /project/!svn/act/c11d45ac-86b6-184a-ac5a-9a1105d64563 HTTP/1.1" 204 - So it seems that it PUTs the file (test.html) correctly, and somehow somewhere something is wrong (file permissions are alright, when I purposely stated that they are wrong, it gave me errors, which is expected, and they were about the file permissions being incorrect. The odd thing is that files won't get added, but directories are fine. I also have enough storage left on my machine. What I should note, perhaps, is that I use Ubuntu 12.04.3 with ruby 1.9.3, mysql 14.14 and I have it set up that Chiliproject handles the authentication and authorization for the project. It works, because I can commit directories and read it all correctly, though I can't upload files. Help would really be appreciated, as I don't know what on earth is going on with this 'truncated http response body'. I tried to read them with wireshark, but it basically gave me the same information. With regards, Ps. I have no clue what the delay between put and delete is, as it's a file of a mere 500 bytes, so it's uploaded in approximately a second. Pps. I copied this question from StackOverflow to this site, as I didn't know the existence of this site and another user suggested that I'd get more answers here, as it's basically a server fault.

    Read the article

  • Aliased network interfaces and isc dhcp server

    - by Jonatan
    I have been banging my head on this for a long time now. There are many discussions on the net about this and similar problems, but none of the solutions seems to work for me. I have a Debian server with two ethernet network interfaces. One of them is connected to internet, while the other is connected to my LAN. The LAN network is 10.11.100.0 (netmask 255.255.255.0). We have some custom hardware that use network 10.4.1.0 (netmask 255.255.255.0) and we can't change that. But we need all hosts on 10.11.100.0 to be able to connect to devices on 10.4.1.0. So I added an alias for the LAN network interface so that the Debian server acts as a gateway between 10.11.100.0 and 10.4.1.0. But then the dhcp server stopped working. The log says: No subnet declaration for eth1:0 (no IPv4 addresses). ** Ignoring requests on eth1:0. If this is not what you want, please write a subnet declaration in your dhcpd.conf file for the network segment to which interface eth1:1 is attached. ** No subnet declaration for eth1:1 (no IPv4 addresses). ** Ignoring requests on eth1:1. If this is not what you want, please write a subnet declaration in your dhcpd.conf file for the network segment to which interface eth1:1 is attached. ** I had another server before, also running Debian but with the older dhcp3 server, and it worked without any problems. I've tried everything I can think of in dhcpd.conf etc, and I've also compared with the working configuration in the old server. The dhcp server need only handle devices on 10.11.100.0. Any hints? Here's all relevant config files: /etc/default/isc-dhcp-server INTERFACES="eth1" /etc/network/interfaces (I've left out eth0, that connects to the Internet, since there is no problem with that.) auto eth1:0 iface eth1:0 inet static address 10.11.100.202 netmask 255.255.255.0 auto eth1:1 iface eth1:1 inet static address 10.4.1.248 netmask 255.255.255.0 /etc/dhcp/dhcpd.conf ddns-update-style none; option domain-name "???.com"; option domain-name-servers ?.?.?.?; default-lease-time 86400; max-lease-time 604800; authorative; subnet 10.11.100.0 netmask 255.255.255.0 { option subnet-mask 255.255.255.0; pool { range 10.11.100.50 10.11.100.99; } option routers 10.11.100.102; } I have tried to add shared-network etc, but didn't manage to get that to work. I get the same error message no matter what...

    Read the article

  • Custom built machine has much higher power consumption than expected

    - by foraidt
    I built a machine according to the specs of a computer magazine (c't, Germany). According to the magazine, the power consumption should be at around 10W. I don't want to go into the specifics of the hardware but rather ask for general advice on where to look: I updated the BIOS/UEFI version to the latest version, installed all the recommended drivers and unplugged all hardware that's not necessary to boot into Windows. All that was left is the power supply, mainboard, cpu, cpu cooler and one SSD drive. But still I measured a power consumption of 50W, which is 40W more than it should be. I tried booting Linux Mint from a USB stick, so I don't think it's some Windows-related problem.. Where else could I look? Update 1 I dind't want the question to get closed for being too localized but if more details are necessary, here they are: The system is a desktop PC. The power consumption is measured using a Brennenstuhl PM 231 device, which was tested also by c't and they found it quite accurate. The PSU is an Enermax ETL300AWT, the mainboard Intel DH87RL (Socket 1150) and the CPU Intel G3220 (Haswell). Update 2 There is no online version of the article*. The most details I found can be read on its project page (in German, though...) (*)You can pay for downloadable PDFs, however. English translation of that project page Update 3 Regarding the sceptics: It may sound ridiculous but apparently 10W idle consumption is possible with Intel's Haswell architecture. As a kind of proof, there's an additional Blog article explicitly listing the steps needed to reduce the idle consumption to 10W. Additional hardware: I measured the consumption without the HDD, and as expected the usage dropped by around 10W. I have no chassis fans and the CPU fan is a "Scythe Mugen 4" model. It runs at around 600rpm so I think it won't draw much. When stripping off all my extra components I should be at 10W. But I'm not getting anywhere near that. I would be happy to see "just" 15W in the stripped down version but currently I'm not getting below 50W no matter which component I remove. As I see it this cannot be explained by the PSU being less efficient at lower consumption. I also waited half an hour or so (also checked that no Windows updates were running in the background) and the consumption dind't drop by more than a few watts.

    Read the article

  • Revolutionary brand powder packing machine price from affecting marketplace boom and put on uniform in addition to a lengthy service life

    - by user74606
    In mining in stone crushing, our machinery company's encounter becomes much more apparent. As a consequence of production capacity in between 600~800t/h of mining stone crusher, stone is mine Mobile Cone Crushing Plant Price 25~40 times, effectively solved the initially mining stone crusher operation because of low yield prices, no upkeep problems. Full chunk of mining stone crusher. Maximum particle size for crushing 1000x1200mm, an effective answer for the original side is mine stone provide, storing significant chunks of stone can not use complications in mines. Completed goods granularity is modest, only 2~15mm, an effective option for the original mine stone size, generally blocking chute production was an issue even the grinding machine. Two types of material mixed great uniformity, desulfurization of mining stone by adding weight considerably. Present quantity added is often reached 60%, effectively minimizing the cost of raw supplies. Electrical energy consumption has fallen. Dropped 1~2KWh/t tons of mining stone electrical energy consumption, annual electricity savings of one hundred,000 yuan. Efficient labor intensity of workers and also the atmosphere. Due to mine stone powder packing machine price a high degree of automation, with out human make contact with supplies, workers working circumstances enhanced significantly. Positive aspects, and along with mine for stone crushing, CS series cone Crusher has the following efficiency traits. CS series cone Crusher Chamber is divided into 3 unique designs, the user is usually chosen in accordance with the scenario on site crushing efficiency is high, uniform item size, grain shape, rolling mortar wall friction and put on uniform in addition to a extended service life of crushing cavity-. CS series cone Crusher utilizes a one of a kind dust-proof seal, sealing dependable, properly extend the service life of the lubricant replacement cycle and parts. CS series Sprial Sand washer price manufacture of important components to choose unique materials. Each and every stroke left rolling mortar wall of broken cone distances, by permitting a lot more products into the crushing cavity, as well as the formation of big discharge volume, speed of supplies by way of the crushing Chamber. This machine makes use of the principle of crushing cavity, also as unique laminated crushing, particle fragmentation, so that the completed product drastically improved the proportions of a cube, needle-shaped stones to lower particle levels extra evenly.

    Read the article

  • Open a terminal window & run command, then close the terminal window if command completed successfully?

    - by Caspar
    I'm trying to write a script to do the following: Open a terminal window which runs a long running command (Ideally) move the terminal window to the top left corner of the screen using xdotool Close the terminal window only if the long running command exited with a zero return code To put it in Windows terms, I'd like to have the Linux equivalent of start cmd /c long_running_cmd if long_running_cmd succeeds, and do the equivalent of start cmd /k long_running_cmd if it fails. What I have so far is a script which starts xterm with a given command, and then moves the window as desired: #!/bin/bash # open a new terminal window in the background with the long running command xterm -e ~/bin/launcher.sh ./long_running_cmd & # move the terminal window (requires window process to be in background) sleep 1 xdotool search --name launcher.sh windowmove 0 0 And ~/bin/launcher.sh is intended to run whatever is passed as a command line argument to it: #!/bin/bash # execute command line arguments $@ But, I haven't been able to get the xterm window to close after long_running_cmd is done. I think something like xterm -e ~/bin/launcher.sh "./long_running_cmd && kill $PPID" & might be what I'm after, so that xterm is launched in the background and it runs ./long_running_cmd && kill $PPID. So the shell in the xterm window then runs the long running command and if it completes successfully, the parent process of the shell (i.e. the process owning the xterm window) is killed, thereby closing the xterm window. But, that doesn't work: nothing happens, so I suspect my quoting or escaping is incorrect, and I haven't been able to fix it. An alternate approach would be to get the PID of long_running_cmd, use wait to wait for it to finish, then kill the xterm window using kill $! (since $! refers to last task started in the background, which will be the xterm window). But I can't figure out a nice way to get the PID & exit value of long_running_cmd out of the shell running in the xterm window and into the shell which launched the xterm window (short of writing them to a file somewhere, which seems like it should be unnecessary?). What am I doing wrong, or is there an easier way to accomplish this?

    Read the article

  • Amazon Elastic Terms and Conditions

    - by PP
    WARNING: Have you really read Amazon's Terms and Conditions? Would anybody seriously agree to this term on Amazon's Elastic services sign up page? 6.2. Restrictions with Respect to Use of Marks. Your use of any trademarks, service marks, service or trade names, logos, and other designations of AWS and its affiliates or licensors, hereinafter "Marks", shall strictly comply with the following provisions. You may use the Marks in conjunction with the display of the AWS Content and for the purpose of indicating that your Application was created using the Services. You may use the Marks only in the form in which we make them available to you and not in any manner that disparages Amazon, its affiliates or its licensors, or that otherwise dilutes any Mark. Other than your limited right to use the Marks as provided in this Agreement, we and our licensors retain all right, title, and interest in and to the Marks. You will not at any time now or in the future challenge or assist others to challenge the validity of the Marks, or attempt to register confusingly similar trademarks, trade names, service marks or logos. You agree to follow our the Trademark Use Guidelines posted on the Amazon Web Services™ Trademark Guidelines page (the "Trademark Guidelines") as those guidelines may change from time to time. The Trademark Guidelines are incorporated herein by reference. You must immediately discontinue use of any Mark as specified by us at any time in writing. We may modify any Marks provided to you at any time, and upon notice, you will use only the modified Marks and not the old Marks. Other than as specified in this Agreement, you may not use any trademark, service mark, trade name or other business identifier of Amazon or its affiliates unless you obtain Amazon's or its affiliates' prior written consent. The foregoing prohibition includes the use of "amazon," any other trademark of AWS, Amazon or its affiliates, or variations or misspellings of any of them, in the name of an Application or in a URL to the left of the top-level domain name (e.g., ".com", ".net", "co.uk", etc.)-for example, a URL such as "amazon.mydomain.com", "amaozn.com" or "amazonauctions.net" are expressly prohibited. Any use you make of the Marks shall inure to our benefit and you hereby irrevocably assign to us all right, title and interest in the same. In addition, you agree not to misrepresent or embellish the relationship between us and you, for example by implying that we support, sponsor, endorse, or contribute money to you or your business endeavors. If you are a large company and you want to use Amazon's services you must agree that: you may not use the word "amazon" in any domain name you control (even if you are a forestry company) you may not use any word Amazon choose to trademark in any domain you control (regardless of whether the name has a different meaning/purpose in your industry) from now until forever you will never dispute any claim Amazon makes on any word you or anybody else uses Seriously, who would sign such a thing?

    Read the article

  • Computer experiencing slowdowns and lockups despite low cpu useage

    - by user157145
    my setup i5-2300 nvidia gtx 550 ti 6 gigs ram 600 w ocz modular psu recently reformatted and already experiencing drastic slowdown as soon as windows comes up, including repeated lockups with multiple various programs reporting that they are not responsive, then recovering after 10-30 seconds. ive checked memory and hard drive both of which come out fine. despite my plethura of worthless antiviral software im forced to assume that my illicit downloading practices have lead me into some comp trouble that i cant seem to determine. i have used ccleaner, search and destroy and malware bytes, all of which have found nothing to indicate what is causing this massive slowdown. in addition according to my resource manager my computer is operating at a load of only 30-50 percent CPU useage and 60 ram useage but taking 5-10 seconds to load files and open folders, and repeated lockups of multiple programs, especially firefox which seems to go unresponsive every 2-3 minutes. any help would be appreciated, i used a program called OTL by old timer, but cant make any sense of the results i was given. any help or suggestions would be appreciated, thank you for taking the time to read this i have avast but it didnt even find anything when i had it do a full system scan, so im thinking its clueless(also nortons, avg, and ad-aware). i also have mse but it has yet to complete a full scan it takes so long (i left it on last night but when i woke up my computer had a problem and had to restart). my hard drive has 300 gigs out of 1tb open and i already used hd tune pro, which said my harddrive was fine and its not a ssd. also im a noob at comps and only have the hd that is currently inside the computer in addition im not sure if studdering is the issue im suffering. my problem is that during my typing of these responses firefox has gone "not responsive" at least 5 times, each for times of about 5-10 seconds. when i try to control alt delete to bring up windows task manager it took 20 seconds. essentially its that my computer goes super slow at bringing up anything, or taking any action whatsoever that opens a program or file and has repeated incidents where i cant even click on whatever im trying to do because it locks up. the confusing thing about these incidents is that its right after restarting where there are minimal programs running and the computer and memory load is light.

    Read the article

  • HAproxy roundrobin balancing does not appear to be distributing evently

    - by andrew
    Hello, I know that with loaded servers, roundrobin in HAproxy (1.4.4) does not evenly distribute, but my servers are currently getting NO traffic (test setup), and roundrobin balancing does www1,www1,www1,www1,www1,...www2,www2,www2,...,www1... I'm verifying this by having the script being run on each server cat /etc/HOSTNAME (slackware). I need to have it switch back and forth each time to test some session stuff (stored in shared memcached) but am having trouble getting it to switch between my two web servers on each request. global log 127.0.0.1 local0 warning maxconn 4096 chroot /usr/share/haproxy pidfile /var/run/haproxy.pid uid 99 gid 99 daemon defaults balance roundrobin fullconn 100 maxconn 4096 mode http option dontlognull option http-server-close option forwardfor option redispatch retries 3 timeout connect 5000 timeout client 20000 timeout server 60000 timeout queue 60000 stats enable stats uri /haproxy stats auth ***:*** frontend www *:80 log global acl is_upload hdr_dom(host) -i uploads.site.com acl is_api hdr_dom(host) -i api.site.com acl is_dev hdr_dom(host) -i dev.site.com acl is_apidev hdr_dom(host) -i apidev.site.com use_backend uploads.site.com if is_upload use_backend api.site.com if is_api use_backend dev.site.com if is_dev !is_apidev default_backend site.com backend site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend api.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:api.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend dev.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:dev.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend uploads.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:uploads.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 backup weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 So basically, I have some different back-ends (I've verified the ACLs are working), with the default option "roundrobin" selected. I've tried removing weights, removing the minconn/maxconn/fullconn attributes for all servers (not just the backend I'm testing), tried removing the ACLs, etc. I've been testing on dev.site.com BTW. Anyone see a reason why I can't get something like www1,www2,www1,www2,...? Also, this is one of my first questions on here, so please let me know if I left anything needed out of my post. Thanks!

    Read the article

  • ruby on rails gitorious setup on ubuntu

    - by dogmatic69
    Ive been trying to install gitorious for a while now which required ruby and rails etc. Ive finally got rails pages serving but cant finish the installation of gitorious because the gem version is too new. the error logs say please run 'rake ultrasphinx:configure' and that gives rake ultrasphinx:configure (in /var/www/apps/gitorious) rake aborted! uninitialized constant ActiveSupport::Dependencies::Mutex /var/www/apps/gitorious/Rakefile:10:in `require' (See full trace by running task with --trace) From searching google this is beacuse of the wrong gem verison. Cant find a way to down grade it. apparently sudo gem update --system 1.4.2 should do the trick but ubuntu 10.10 does not like this. ERROR: While executing gem ... (RuntimeError) gem update --system is disabled on Debian, because it will overwrite the content of the rubygems Debian package, and might break your Debian system in subtle ways. The Debian-supported way to update rubygems is through apt-get, using Debian official repositories. If you really know what you are doing, you can still update rubygems by setting the REALLY_GEM_UPDATE_SYSTEM environment variable, but please remember that this is completely unsupported by Debian. So i added export REALLY_GEM_UPDATE_SYSTEM=1 to .bashrc and reloaded it with . ~/.bashrc and still the same. ive tried various forms of setting this environmental variable with no luck. Ive also been told on #gitorious irc channel to add the file config/initializers/rubygems.rb with the line require "thread" to it. This has done nothing. EDIT: Just found another way which was rvm install rubygems 1.4.2 and it gave: Removing old Rubygems files... Installing rubygems dedicated to ruby-1.8.7-p334... Retrieving rubygems-1.4.2 % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 288k 100 288k 0 0 282k 0 0:00:01 0:00:01 --:--:-- 414k Extracting rubygems-1.4.2 ... Installing rubygems for /home/ubuntu/.rvm/rubies/ruby-1.8.7-p334/bin/ruby ERROR: Error running 'GEM_PATH="/home/ubuntu/.rvm/gems/ruby-1.8.7-p334:/home/ubuntu/.rvm/gems/ruby-1.8.7-p334@global:/home/ubuntu/.rvm/gems/ruby-1.8.7-p334@global" GEM_HOME="/home/ubuntu/.rvm/gems/ruby-1.8.7-p334" "/home/ubuntu/.rvm/rubies/ruby-1.8.7-p334/bin/ruby" "/home/ubuntu/.rvm/src/rubygems-1.4.2/setup.rb"', please read /home/ubuntu/.rvm/log/ruby-1.8.7-p334/rubygems.install.log WARN: Installation of rubygems did not complete successfully. TL;DR please tell me how to downgrade rubygems on ubuntu 10.10 or upgrade gitorious to work with 1.6.2 gems

    Read the article

  • New monitor connected to HDMI adaptor doesn't show output after booting

    - by Paul
    Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you. Thank you Anees Bakrain Only the ATI Radeon HD 4300/4500 Series adapter is displayed in the Device Manager, for that reason I have to assume that the onboard display adaptor is not active. All 40 drivers of Sarastro2 are up to date and the HDMI cable can not be the problem because both monitors displayed the boot sequence up to the moment when Windows 7 was loaded completely. This was the moment, when the Asus monitor lost its signal. Both connectors, HDMI and DVI are connected and removing the DVI connector would not solve my problem of running both monitors simultaneously. However, your suggestions shifted my seventy one year old brain into the next gear. The only question remaining is; “Why the signals to the Asus monitor stop after the sequence is complete”. The ATI Radeon HD 4300/4500 Series adapter seems to be capable of sending simultaneous HDMI and DVI signals, what is done during the boot sequence. Why do the signals change after the boot sequence is complete is the key question or der springende Punkt? Is this a correct assumption slhck?

    Read the article

  • A dusty server room

    - by pauska
    Here's the story.. The owners of the building we lease office space from decided to do a renovation of the exterior. This involved in some pretty heavy work at the level where our server room is, including exchanging windows wich are fit inside a concrete wall. My red alert went off when I heard that they were going to do the same thing with our server room (yes, our server room has a window. We're a small shop with 3 racks. The window is secured with steel bars.) I explicity told the contractor that they need to put up a temporarily wall between our racks and the original wall - and to make sure that the temporary wall is 100 % air and water-tight. They promised to do so. The temporary wall has a small door in it, so that workers can go in/out through the day (through our server room, wich was the only option....). On several occasions I could find the small door half-way shut while working evenings/nights. I locked the door, and thought that they would hopefully get the point soon and keep the door shut. I even gave a electrician a mouthful when I saw that he didn't close the door properly. By this point - I bet that most of you get a picture of what happened. Yes, they probably left the door open while drilling in the concrete. I present you our 4 weeks old EMC VNX: I'll even put in a little bonus, here is the APC UPS one rack further away from the temporary wall. See the nice little landing strip from my finger? What should I do? The only thing that comes to mind is to either call all our suppliers (EMC, HP, Dell, Cisco) and get them to send technicians to check out all the gear in the server room, or get some kind of certified 3rd-party consulant to check all of it. Would you run production systems on this gear? How long? Edit: I should also note that our aircondition isn't exactly enterprise-grade, given the nature of our small room. It's just a single inverter, wich have failed one time before I started working here (failed inverters usually leads to water dripping out).

    Read the article

  • Windows 7 Administrator HomeUsers Account

    - by Charles Carrington
    I'm trying to login to my Windows 7 PC from another PC so that I can transfer files to the Windows 7 PC. I've just installed Visual Studio 2008 on my new PC, and I wan't to transfer all of my work from my old machine to my new one. When I first set up a user on the Windows 7 PC after a reformat, the account created had a Group field that read "HomeUsers; Administrators" when viewing it from the User Accounts screen. You get to this screen by typing "netplwiz" in the search field of the Start Menu. I changed the Group of this account to Administrators before I realized that it was assigned to two Groups -- "HomeUsers; Administrators" as I mentioned above. I was trying to make sure that it was an Administrator account so I didn't have to type in a password everytime I wanted to install software. I can use this computer normally without being asked for an administrator password all the time when I want to install new software, but I can't log in to this PC from another PC because I don't have an account that has a Group of "HomeUsers". I should have left the account alone; everything would've been fine. But there doesn't seem to be a way to assign it to two groups after the initial assignment that take place automatically when you are setting up your computer for the first time. If you assign "HomeUsers" to the account, the Group field on the User Accounts screen will just read "HomeUsers". If you assign "Administrators" to the account, the Group field on the User Accounts screen will just read "Administrators". There's no way to make it read "HomeUsers; Administrators" again. If you don't have at least one account that is a "HomeUsers" account, you cannot log in to the PC from another PC on the network. If you don't have an account that is an "Administrators" account, you cannot install software on your machine without being asked for an Administrator password all the time, which is very annoying. I want an account on my Windows 7 PC that I can use to install software without being asked for a password AND that I can log into from another PC on the network to transfer files. If I could make the Group field read "HomeUsers; Administrators" of my primary account on the Windows 7 PC when I go to the User Accounts screen by typing "netplwiz" in the search field of the Start Menu, my primary account would do what I want it to do. Does anybody know how to make an account in Windows 7 a "HomeUsers" account AND an "Administrators" account? As I said before, Windows 7 does this for you automatically when you first set up your computer. But if you change it inadvertently, there is no way to change it back. At least I don't know how to do it. If anybody has any ideas on how to fix this, I would greatly appreciate it. Thanks, Charles Carrington

    Read the article

  • Is Samba Server what I'm looking for, and if so, what do I need? (currently on DD-WRT Micro)

    - by Anthony
    I am really confused as to what Samba actually does and how it works. Here's what I'm hoping it does: I set up a Samba server on my LAN, and everyone will be able to see each other's shared files and swap them. But some of the documentation makes it sound like it will just allow Mac/Linux computers to see Windows computers. Other bits of the documentation make it sound more like a local server, where a Linux machine would install Samba and they would see everyone and be visible to everyone, but that won't change if anybody else can see each other. While still other things I've read make it seem more like a file-server, where everyone sees each other but file transfers are not peer-to-peer but instead need a host disk for files to act as go between. So, assuming I'm even in the right ballpark of what Samba does in terms of my goal of total cross-visibility on the network, I am left with needing to know what I'd need to set up the server and whether it can be done and is worth it... DD-WRT's article on Samba is a bit ambiguous. One second it sounds as if I can run the server on micro as long as it's set up on a usb drive, but then it also sounds like micro can't run it at all, etc. If I can run it from a usb-connected drive, I still need to know if the files are actually stored on that drive. The dd-wrt article mentions: You can run a Samba server on your main computer and run a client on your router (thus gaining writable storage for the router) or you can use Samba to share a drive connected (typically by USB) to the router among all the computers connected to your network. That one part "to share a drive...among all the computers" makes it sound like the only benefit I get from Samba is a share drive that any OS on the network can see, but they still won't see each other. But I'm very hopeful I'm misreading this. If the computers can see each other but still need the disk, how much space is generally a good idea? I'm basing this on the idea that the drive is a temporary store point. Obviously I'd have to get a drive big enough to store everything people wanted to share if the drive is a full-on file server. If I do have this all wrong, is there any software that achieves what I have in mind? Something that connects to the main router to bridge all clients?

    Read the article

  • Dangers of Running Computers w/o Air Conditioning

    - by Daniel Bingham
    I recently moved in to an apartment with out air conditioning. This is fine most of the time as I am in upstate New York. It only ever gets above the high 70s during the hottest of the summer months. And when it does, I'm stubborn enough that I'll just deal with wearing minimal clothing around the house. However, I'm worried about my computers. I'm a software developer and gamer, so many of my machines are very high powered. And at least one of them is a server that must be left on 24/7 (not just a game server - also serves multiple websites). I've never before had to worry about the heat too much, as I always lived in buildings with central air. The in building temperature rarely got much above 70 F. All of the machines I built had good enough air cooling that I never saw a problem. Now the temperature in building is pushing 100F and I'm worried that the machines will not be able to keep themselves cool enough by simply blowing already hot air over themselves. The hottest of them I've turned off. However, the server I cannot. It's an old Dell (not custom build) that runs on a Pentium 4 (2.2GHz). It only has a single hard drive, integrated video. And it'd not running any processor intensive servers. Just basic LAMP. It used to run a MUD server, but that's off for now. So it should be idling most of the time. I haven't been able to find any sort of built in temperature sensors in the hardware... at least not any that the programs I've found in the Debian repository can read. And it's an inherited machine to which I do not have the full specs, so I don't know the tolerances anyway. How worried should I be about it melting down on me? How worried should I be about the hard drive melting or becoming corrupted? To generalize the question for other people, what are the safe temperature tolerances for most machines. How widely does it vary, and how does one go about determining when their machine is running too hot and needs to be shut down?

    Read the article

  • Cannot change default application association of certain file types

    - by H.B.
    After associating my MP3 files with MPlayer i can no longer change that association using the Choose default program... dialogue, the Always use this [...] Checkbox is always greyed out (Control Panel > Default Programs > Associate a file type or protocol with a program does not let me change it either). That also happened for MP4s but not for MKVs for example, and if i associate my MP3s with other applications like VLC it does not get blocked. I would really like to know why that is and if i can avoid this beforehand (thankfully i know ways to fix it afterwards already). Edit: Another obervation: The blocking programs (i managed to block it with an association to Visual Studio as well) do not appear in the Recommended Programs of the open-with-dialogue (And the explorer said: "The current program is not recommended, but i won't let you change it, ha!"). Edit: A screenshot as requested: As you can see on the top left (if you know the icon of MPlayer), the file is currently associated with MPlayer. Edit: Ways to fix it (Note: This question is not about fixing it) Using the Default Programs Control Panel > Default Programs > Set Default Programs, select WMP, Choose defaults for this program, check .mp3 This should reassociate the files with WMP and you can create a new association in the explorer. Using the registry (As always, keep your hands off it unless you know what you are doing or if you are fine with accidentally breaking your system) HKEY_CURRENT_USER > Software > Microsoft > Windows > CurrentVersion > Explorer > FileExts > .mp3 Here you could for example clean up the open-with-list, and the current default program seems to be saved here as well in the key UserChoice, there you can change the ProgId string to another application, you can associate it with WMP by entering WMP11.AssocFile.MP3 or just pick another application right away. You may need to mess with permissions on the key though, if you cannot change the ProgId value.

    Read the article

  • Unextending Sharepoint 2007 Web Application from a zone

    - by dunxd
    When our Sharepoint was migrated from Sharepoint 2003 to Sharepoint 2007 (both fully paid versions), the consultants who carried it out extended each web app into two IIS sites/zones (e.g. the original Web App was http://intranet, then http://newintranet and http://intranet would be created for Sharepoint 2007 - each with its own IIS site). The idea was that during the migration period we would set up DNS to point the old url to SP2003 servers and the new one to SP2007, then once the migration was complete, do a DNS change so the SP2007 would recieve the requests to the http://intranet type URLs. Unfortunately the contractors did not tidy up the application extensions and IIS sites after the migration, and for some time both URLs were in use, resulting in many document links pointing to the http://newintranet type URLs. This means I need to maintain these URLs. Due to a rejig of organisation structure we now need to relocate some Sharepoint sites, and I'd like to use the RDA Collaboration Sharepoint URL Redirector feature. However a limitation of this is that it doesn't work for Web Applications which have been extended into multiple zones. So I have a need to tidy up the situation that our consultants left behind. I think the right thing to do is use the "Remove Sharepoint from IIS Web Site" page in Central Admin to remove the zone for the newintranet type sites, and select the option to also delete the IIS site. That should result in having no IIS sites listening for http://newintranet type URLs. Is this the right procedure? Once I have done that I need to set up Sharepoint to receive requests sent to the http://newintranet type URLs so they will continue to work. I am not sure if I should do this: using Alternative Access Mappings or, by adding a host header to the IIS site or, creating a non Sharepoint IIS site for each http://newintranet type URL, and use IIS redirection to forward the requests to the new URL using variables to pass the path to the Sharepoint site. Does anyone have any thoughts on these options, or any other way of achieving this? Sharepoint 2007 is running on Windows 2003 with IIS6. We don't currently have plans/budget to upgrade to Sharepoint 2010.

    Read the article

  • PSU failing or Mainboard failing?

    - by Andrei Rinea
    I am having some troubles lately powering on my desktop workstation. While starting up the PC after being off for hours (usually at least 8 hours) it randomly fails to do so. What happens is that : I press the power button; nothing happens I can hear a moderate buzzing noise at the back of the PC (near the PSU); but I can't say for sure that it's not from the mainboard. If I insist pressing the power button a few times in 1-2 minutes it'll start Another route would be that instead of (3) I will plug off the power cable from the PSU and wait for 30 seconds. Then I will press the power on and keep it for 30-60 seconds (I had some success at notebooks with a similar approach). Then I will plug back the cable in the PSU, press only once the power button and it will start normally. Also while running normally I keep hearing some low buzzing which seems to be fan-RPM-related (i.e. when processing images or doing CPU intensive work). What should I look into? UPDATE It's getting worse. It took more than 10 retries today and almost 20 minutes to start the computer. I tried the paperclip trick and the PSU behaves perfectly. I managed to start the computer like so : I pressed the on-button a few times and then left the PC in a pre-startup state (the fans were working the buzzing noise was strong and I went to eat. I thought I won't lit the house on fire so fast and without smelling. Back, after 10-15 min the computer booted up! Discussed with a fellow at Intel and he told me the capacitors on the mainboard are probably a bit shot. If they are shot, he said, it should start up warm perfectly. So I did restart it, warm, a few times (5 sec cooldown and then 40 sec cooldown and it started up perfectly). I can either replace the capacitors on the mainboard (doesn't sound worth it or replace the mainboard (this one sucks too :)) ) FINAL INFO : It was the PSU after all. Although it was powering the IDEs and SATAs the Mainboard power module was failing. I bought another mainboard just to find out that this wasn't the cause. Now I'll have to return it somehow. The spare PSU is now in the computer and doing well.. Although larger (500W), it's like a plane taking off.. I need a better one.

    Read the article

  • Can't save screen resolution setting.

    - by Searock
    Hi, My screen resolution in windows and previous version of Ubuntu (9.04) was 1152 x 864. But in Ubuntu 10.04 it gives me an option of 1024 x 786 and 1360 x 786. I have some how managed to add 1152x684 resolution by using xrandr command. searock@searock-desktop:~$ cvt 1152 864 1152x864 59.96 Hz (CVT 1.00M3) hsync: 53.78 kHz; pclk: 81.75 MHz Modeline "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync searock@searock-desktop:~$ xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync searock@searock-desktop:~$ xrandr --addmode S-video 1152x864 xrandr: cannot find output "S-video" searock@searock-desktop:~$ xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1360x768 59.8 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9 59.9 1152x864_60.00 (0x124) 81.0MHz h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.3KHz v: height 864 start 867 end 871 total 897 clock 59.4Hz searock@searock-desktop:~$ xrandr --addmode VGA1 1152x864_60.00 But the problem is when ever I restart my computer I get this message. Could not apply the stored configuration for the monitors. Could not find a suitable configuration of screens. And then it comes back to 1024 x 786 My graphic card details : Intel(R) 82945G Express Chipset Family. Is there any way I can fix this once for all ? Thanks. Edit 1 : rumtscho has suggested me to modify xorg.conf file. But I am not sure what HorizSync means? is it Horizontal frequency ? My monitor model is Acer v173. Here's my specification. So what should be HorizSync and VertRefresh ? Edit 2 : I have edited my Xorg.conf file as follows : Section "Monitor" Identifier "Configured Monitor" HorizSync 30-80 VertRefresh 55-75 EndSection then I added the resolution and restarted my computer and still I am facing the same problem. Is there something that I am missing? Edit 3 : For now I have edited /etc/gdm/Init/Default(gdm startup scripts) to include following xrandr commands, just below line initctl -q emit login-session-start DISPLAY_MANAGER=gdm xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync xrandr --addmode VGA1 1152x864_60.00<br/> xrandr -s 1152x864_60.00 This has solved my problem, but this commands have increased my computer's boot time. I think I will have to edit xorg file properly. Edit 4 : Instead of adding this files to gdm startup scripts I have created a shell script and added it to startup (System - Preference - Startup Applications) #!/bin/bash xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync xrandr --addmode VGA1 1152x864_60.00 xrandr -s 1152x864_60.00 And don't forget to add execution rights. (Right Click - Properties - Permission - Allow executing file as program)

    Read the article

  • Package problems after upgrade

    - by Dan
    I installed a new upgrade on ubuntu which seemed to fail near the end. Now I'm being told that an error has occurred and to please run apt-get to see what's wrong. After some further tries with that I eventually gave up. It seems there's a left over latex package(?) somewhere and I can't seem to get rid of or fix it. Here's an example: blank@ubuntu:~$ sudo apt-get dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: tex-common : Breaks: texlive-common (< 2010) but 2009-15 is installed texlive-base : Depends: texlive-binaries (>= 2012.20120516) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-doc-base : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-extra-utils : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed texlive-font-utils : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-generic-recommended : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-base : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-base-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-extra : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-extra-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-recommended : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-recommended-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-luatex : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pictures : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pictures-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pstricks : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pstricks-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed zlib1g : Breaks: texlive-binaries (< 2009-12) but 2009-11ubuntu2 is installed zlib1g:i386 : Breaks: texlive-binaries (< 2009-12) but 2009-11ubuntu2 is installed E: Unmet dependencies. Try using -f. I've seen similar errors on the site here, but not close enough that i could get it fixed. Any help would be great, Thanks

    Read the article

  • Excessive Outbound DNS Traffic

    - by user1318414
    I have a VPS system which I have had for 3 years on one host without issue. Recently, the host started sending an extreme amount of outbound DNS traffic to 31.193.132.138. Due to the way that Linode responded to this, I have recently left Linode and moved to 6sync. The server was completely rebuilt on 6sync with the exception of postfix mail configurations. Currently, the daemons run are as follows: sshd nginx postfix dovecot php5-fpm (localhost only) spampd (localhost only) clamsmtpd (localhost only) Given that the server was 100% rebuilt, I can't find any serious exploits against the above stated daemons, passwords have changed, ssh keys don't even exist on the rebuild yet, etc... it seems extremely unlikely that this is a compromise which is being used to DoS the address. The provided IP is noted online as a known SPAM source. My initial assumption was that it was attempting to use my postfix server as a relay, and the bogus addresses it was providing were domains with that IP registered as their nameservers. I would imagine given my postfix configuration that DNS queries for things such as SPF information would come in with equal or greater amount than the number of attempted spam e-mails sent. Both Linode and 6Sync have said that the outbound traffic is extremely disproportionate. The following is all the information I received from Linode regarding the outbound traffic: 21:28:28.647263 IP 97.107.134.33.32775 > 31.193.132.138.53: 28720 op8+% [b2&3=0x4134] [17267a] [30550q] [28773n] [14673au][|domain] 21:28:28.647264 IP 97.107.134.33 > 31.193.132.138: udp 21:28:28.647264 IP 97.107.134.33.32775 > 31.193.132.138.53: 28720 op8+% [b2&3=0x4134] [17267a] [30550q] [28773n] [14673au][|domain] 21:28:28.647265 IP 97.107.134.33 > 31.193.132.138: udp 21:28:28.647265 IP 97.107.134.33.32775 > 31.193.132.138.53: 28720 op8+% [b2&3=0x4134] [17267a] [30550q] [28773n] [14673au][|domain] 21:28:28.647266 IP 97.107.134.33 > 31.193.132.138: udp 6sync cannot confirm whether or not the recent spike in outbound traffic was to the same IP or over DNS, but I have presumed as such. For now my server is blocking the entire 31.0.0.0/8 subnet to help deter this while I figure it out. Anyone have any idea what is going on?

    Read the article

  • Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

    - by CapBBeard
    Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

    Read the article

  • 40k Event Log Errors an hour Unknown Username or bad password

    - by ErocM
    I am getting about 200k of these an hour: An account failed to log on. Subject: Security ID: SYSTEM Account Name: TGSERVER$ Account Domain: WORKGROUP Logon ID: 0x3e7 Logon Type: 4 Account For Which Logon Failed: Security ID: NULL SID Account Name: administrator Account Domain: TGSERVER Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x334 Caller Process Name: C:\Windows\System32\svchost.exe Network Information: Workstation Name: TGSERVER Source Network Address: - Source Port: - Detailed Authentication Information: Logon Process: Advapi Authentication Package: Negotiate Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols. - Key length indicates the length of the generated session key. This will be 0 if no session key was requested. On my server... I changed my adminstrative username to something else and since then I've been inidated with these messages. I found on http://technet.microsoft.com/en-us/library/cc787567(v=WS.10).aspx that the 4 means "Batch logon type is used by batch servers, where processes may be executing on behalf of a user without their direct intervention." which really doesn't shed any light on it for me. I checked the services and they are all logging in as local system or network service. Nothing for administrator. Anyone have any idea how I tell where these are coming from? I would assume this is a program that is crapping out... Thanks in advance!

    Read the article

  • How can I reverse mouse movement (X & Y axis) system-wide? (Win 7 x64)

    - by Scivitri
    Short Version I'm looking for a way to reverse the X and Y mouse axis movements. The computer is running Windows 7, x64 and Logitech SetPoint 6.32. I would like a system-level, permanent fix; such as a mouse driver modification or a registry tweak. Does anyone know of a solid way of implementing this, or how to find the registry values to change this? I'll settle quite happily for how to enable the orientation feature in SetPoint 6.32 for mice as well as trackballs. Long Version People seem never to understand why I would want this, and I commonly hear "just use the mouse right-side up!" advice. Dyslexia is not something which can be cured by "just reading things right." While I appreciate the attempts to help, I'm hoping some background may help people understand. I have a user with an unusual form of dyslexia, for whom mouse movements are backward. If she wants to move her cursor left, she will move the mouse right. If she wants the cursor to move up, she'll move the mouse down. She used to hold her mouse upside-down, which makes sophisticated clicking difficult, is terrible for ergonomics, and makes multi-button mice completely useless. In olden times, mouse drivers included an orientation feature (typically a hot-air balloon you dragged upward to set the mouse movement orientation) which could be used to set the relationship between mouse movement and cursor movement. Several years ago, mouse drivers were "improved" and this feature has since been limited to trackballs. After losing the orientation feature she went back to upside-down mousing for a bit, until finding UberOptions, a tweak for Logitech SetPoint, which would enable all features for all pointing devices. This included the orientation feature. And there was much rejoicing. Now her mouse has died, and current Logitech mice require a newer version of SetPoint for which UberOptions has not been updated. We've also seen MAF-Mouse (the developer indicated the version for 64-bit Windows does not support USB mice, yet) and Sakasa (while it works, commentary on the web indicate it tends to break randomly and often. It's also just a running program, so not system-wide.). I have seen some very sophisticated registry hacks. For example, I used to use a hack which would change the codes created by the F1-F12 keys when the F-Lock key was invented and defaulted to screwing my keyboard up. I'm hoping there's a way to flip X and Y in the registry; or some other, similar, system-level tweak out there. Another solution could be re-enabling the orientation feature for mice, as well as trackballs. It's very frustrating that input device drivers include the functionality we desperately need for an accessibilty concern, but it's been disabled in the name of making the drivers more idiot-proof.

    Read the article

  • GPU not powering on

    - by Lerp
    So I got home from work yesterday and went to turn my computer on as per usual to be greeted by this: The screens remained black, so I rebooted; I go as far as GRUB before my screens went black again. I rebooted again, they didn't turn on. I rebooted again, I got as far as the windows login screen. This time I unplugged it, opened it up and cleaned it but to no luck. The GPU was still being tempermental. I repeated the process of turning off and on several times until one time it work as normal. I happily played games for the rest of the night (5-6 hours?) thinking everything was jolly good now. Well I get home from work today and it is doing the SAME thing. Sometimes everything displays normally for a few seconds to minutes then the screens go black; then sometimes the screens don't come on at all. Summary and additional points Screens sometimes turn on before shortly turning off, sometimes they don't; I cannot seem to determine any pattern between when they do or do not turn off. The build has been working fine for about 8 months now so I know it's not hardware incompatibility. If I plug a monitor into the on board graphics I can use the PC normally (just in low graphics mode) I have two monitors and it's a case of they both turn on or not. So I think I can rule out the monitors being dead. I have tried replacing the GPU I have tried replacing the RAM I have tried flashing the CMOS I have tried cleaning the inside The GPU is a Radeon HD 7870 My questions Is my GPU dead? It's not very old and I would rather have a method of being certain it's the GPU before I fork out some money I can't really afford. I do not have a second PC here to test it in. If my GPU is dead why does it sometimes work and sometimes not? Update Okay, it was working again.. at least I thought it was. I left it running for 10-20minutes with the screens black. Turned it off and straight back on and it worked for all of 10minutes. I was then updating the post in joy thinking I could play some games for the rest of the night when BAM it went black again. So yeah, I don't know :C

    Read the article

< Previous Page | 476 477 478 479 480 481 482 483 484 485 486 487  | Next Page >