Search Results

Search found 26810 results on 1073 pages for 'fixed point'.

Page 484/1073 | < Previous Page | 480 481 482 483 484 485 486 487 488 489 490 491  | Next Page >

• Identifying Hard Drive as performance bottleneck for desktop machines

  - by Programming Hero

  I'm working in a development team where we all use laptops so we can work in multiple locations. These laptops are proving notoriously slow for development work, but at a glance they all look to have the specification for a much faster experience: CPU - Intel Core 2 Duo T7500 Memory - 2GB of RAM We all experience the biggest delays when the hard-drives are being accessed, particularly when swap-files are being thrashed. After doing a little bit of profile, a colleague discovered that our HDDs are seeing Read/Write speeds of about 10MB/sec. This seems abnormally low and we believe it the cause of the problem. Sensibly (though somewhat annoyingly) our business wont blow money on faster drives just to see if it fixes the problem; we need to illustrate this is definitely the problem and that buying some solid-state drives will make it go away. I need some way of showing how 90% of the system resources aren't being used over the course of a day, and that whenever there is utilization, it's all in HDD reads or writes. Are there any tools I could use to provide this information? Does it seem likely the problem is going to be fixed by a faster drive? Should I be looking for alternatives?

  Read the article

• Copy from CDROM is very slow in Ubuntu

  - by ???

  I'm using the command to copy CDROM image: # dd if=/dev/sr0 of=./maverick.iso But it's very slow, at about 350k bytes/sec. I've searched the google, and try the command # hdparm -vi /dev/sr0 /dev/sr0: HDIO_DRIVE_CMD(identify) failed: Bad address IO_support = 1 (32-bit) readonly = 0 (off) readahead = 256 (on) HDIO_GETGEO failed: Inappropriate ioctl for device Model=DVD-ROM UJDA775, FwRev=DA03, SerialNo= Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=unknown, MaxMultSect=0 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=yes, tPIO={min:180,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 *udma2 AdvancedPM=no Drive conforms to: ATA/ATAPI-5 T13 1321D revision 3: ATA/ATAPI-1,2,3,4,5 * signifies the current active mode Seems like DMA is already on. And a device test gives: # hdparm -t /dev/sr0 /dev/sr0: Timing buffered disk reads: 2 MB in 6.58 seconds = 311.10 kB/sec # sudo hdparm -tT /dev/sr0 /dev/sr0: Timing cached reads: 2 MB in 2.69 seconds = 760.96 kB/sec Timing buffered disk reads: m 4 MB in 5.19 seconds = 789.09 kB/sec The CD-ROM device and disc should be okay because I can copy it very fast in Windows, using UltraISO utility. So I guess there is something not configured right in Ubuntu, is it?

  Read the article

• Exchange server issues - can't upgrade to SP3 - trying to migrate to Exchange 2010

  - by Keith

  Our Exchange server is having a lot of issues. It can't get Windows Updates anymore (error 8000FFFF) and it has a lot of other issues that are all related (Server Manager error - Catastrophic failure exception hresult 8000FFFF). Everything I've read online about it says you pretty much have to re-install Windows to fix it. Because of that, we are going to migrate to a new server running Exchange 2010. I have the new server ready and I was doing the pre-requisite checker and it was complaining that the Exchange 2007 installation wasn't SP2 or newer. I checked and indeed, it is SP1. So I am trying to upgrade the Exchange 2007 installation to SP3, however, it is failing. It is hanging on "Removing Exchange files." I followed these instructions and it's still not working. I can get to the part where you run the upgrade from command line but it starts asking for the exchangeserver.msi file. I point it to where it is located but it keeps asking for it. I am starting to get concerned that I can't upgrade the Exchange server because of the same issues above. My next step is to call Microsoft about the issue because I need to get it fixed however I wanted to check here first.

  Read the article

• Intel Rapid Storage / Smart Response SSD caching issue

  - by goober

  Background Recently built my own PC. It works! Almost. It's been a while since getting into the guts of these things, so I'm familiar but may be missing something simple. FYI, I don't care about blowing the OS away -- it's brand new and we can go back from scratch as many times as necessary. Goal / Issue I'd like to use the SSD to take advantage of Intel's Smart Response technology (allows the SSD to act as a cache for HDDs) I would like the SSD cache to act as a cache for my HDDs, which I would like to be in a RAID1 array (so I get the speed from the SSD and the redundancy from the RAID1) However, Windows only sees the drive in device manager (not as a drive), so I'm unsure what to do about that. Related: as far as I know, for this to work, the drives all have to be in a single RAID array (i.e. a RAID0 pairing of the SSD and the RAID1 HDD array). However, when attempting this at the BIOS level, I am told there is not enough space for an array. Steps so Far Moved the SSD onto the Intel controller (I'd had it on the Marvel 6.0 controller instead of the Intel controller, so the BIOS was only seeing it in a strange way) Updated the BIOS of the motherboard to the latest version Reinstalled Intel's RST (iRST?) software several times, as some forums reported it working after reinstalling 3 times (which does not inspire confidence). Checked Intel storage: it does see the SSD as a physical, non-RAID device. However, it says no space exists if I try to create an array. Checked the BIOS: it does not show up in the boot order, but is an option that can be selected under boot options. Tried the firmware update for that model. Issue: the firmware CD doesn't detect a drive; maybe the Intel storage controller is making it difficult? moved the ssd to the marvel controller. The firmware update cd appeared to hang while searching for drives. swapped out the SATA cable for the manufacturer's and moved back to the intel storage controller. Noticed at this point that in the Intel RST software, a device DOES show up in addition to the RAID set -- only shown as a "60 GB internal disk". Windows doesn't appear to see it as a drive, but it does still show in device manager. Move SSD to port from 0-3 on MOBO and set SATA mode to IDE (after disconnecting RAID1 config) to allow the firmware update to work. Firmware was already at the latest version. Next Steps ? Components involved ASUS P8Z68-V PRO motherboard (Intel Z68 Chipset) Intel i7 2600k Processor 2 x 1TB 7200 RPM HDDs 64 GB Crucial M4 SSD (M4-CT064M4SSD2) For Reference -- Storage Configuration Intel 3 gbps Intel 3gbps Intel 6gbps Marvel 6gbps +----------+ +----------+ +----------+ +----------+ | | <----+ | | +-+ | | | |----------| | |----------| |-|--------| |----------| | | | | + | | | | | | +----------+ | +--|-------+ +-|--------+ +----------+ | | | + v v | 1 TB HDD 64 GB SSD + +> 1 TB HDD For Reference -- Intel RST (v10.8.0.1003) Screenshot Don't mind the "rebuilding" -- knocked a power cable out at one point; it's doing its job, not an indicator of a bad HDD. Any thoughts? Thanks in advance for any help!

  Read the article

• Linux DHCPD Mac-Address based Groups

  - by GruffTech

  Our Current DHCPD.conf looks like the following. subnet 10.0.32.0 netmask 255.255.255.0 { range 10.0.32.100 10.0.32.254; option subnet-mask 255.255.255.0; option broadcast-address 10.0.32.255; option domain-name-servers 208.67.222.222,208.67.220.220; option routers 10.0.32.5; host Dev-ABaird-W { hardware ethernet 00:1D:09:3E:49:13; fixed-address 10.0.32.94; } ... more static hosts .... } About as basic as it gets. The old router is 10.0.32.1, our company wanted to implement a squid proxy to better monitor web traffic while at work, and if necessary block large time-wasters, IE Facebook.com. However, we've quickly realized that this change has played a mean prank on our Polycom SIP Phones. Occasionally our phones will not ring, the end recipient hears ringing (this is artificially created by our PBX) however the handset never rings. The ONLY thing that has changed in our network is the option routers line. So, Since all Polycom MAC addresses begin with 00:04:F2 would it be possible in DHCP to say any 00:04:F2:::* MAC addresses get option routers 10.0.32.1, and anything else must talk with our Gateway?

  Read the article

• MacBook Pro (OSX Lion) - shutdown automatically before reaching login screen

  - by mkk

  When I try to lunch my MacBook Pro I can see a progress bar on loading screen. It goes to 1/15 or something like this and then it shut downs - I cannot reach even login screen. It happened to me 2 months ago, I have 'fixed' this by formatting my hard drive and installing OSX (Lion) again. This time I think that situation is a little bit different - I am able to enter single-user mode by pressing cmd + s. I then type /sbin/fsck -yf, I get the error: ** Checking Journaled HFS Plus volume. The volume name is Macintosh HD ** Checking extents overflow file. ** Checking catalog file. Invalid node structure (4, 24704) ** The volume Macintosh HD could not be verified completely. /dev/rdisk0s2 (hfs) EXITED WITH SIGNAL 8 but when I type exit, I can the login screen and I can log in. I tried a lot of things, booting from recovery partition and choosing disk utility to repair the disc, but I get error that it cannot be repaired. I have googled for hours and the only real solution I have found was to buy Disc warrior that might fix the issue. Any other suggestions? Secondary question is what causes this issue? I thought the reason are bad sectors, but Smart Utility haven't found any. I found suggestion that RAM could cause this kind of issue as well, so I downloaded rember and made memory test - all tests passed. Right now I have used my solution of entering single-mode user and then typing exit, however I am not sure how long it will 'work'. Of course I have back-uped what I considered important. Thanks for the help in advance! UPDATE: I guess Smart Utility was not very useful, I mnaged to get input/output error, which I believe is equivalent to bad sector.

  Read the article

• windows 7: Event 55 The file system structure on the disk is corrupt and unusable

  - by Radio

  Here is a real bad one! Windows 7 RTM with SP1 installed [Version 6.1.7601]. Recently tried to delete some folder on my hard drive and Windows prompted "Error 0x80070570: The file or directory is corrupted and unreadable", and at the same time placed an Event 55 describing "The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on \Device\HarddiskVolume2." Ran chkdsk, first with /f option, then with /r option. Result in both cases was: no errors found, 0 bad sectors. No problems chkdsk found at all! Went through StackExchange, Google and spent over 6 hours on this. Still cannot figure out the problem. Re-installing/Re-Formatting is not an option! What did I try: Hotfix - Windows6.1-KB982927-x64.msu - gave me an error about incompatibility with my computer, however it totally matches my system. CRC of hotfix was ok. Windows Repair Console found startup errors and fixed those, but this didn't help an issue, even by running chkdsk c: /R from it. http://support.microsoft.com/kb/246026 does not promise anything good. sfc /scannow does not help too. Replaced hard drive by cloning an old one using True Image, repeated all steps above. At the same time, some minor glitches started to appear in my Windows, like side panel and notification area settings are getting reset. Goal is to delete the folder and get rid of Event 55. Sounds like NTFS bug. Please help. This is completely ridiculous.

  Read the article

• moving raid 10 to another identical server both on Smart Array 6i controllers

  - by SalimQrdl

  I have dead HP DL 380G4 with RAID 1+0 with 1 logical volume from 4x72GB drives on built-in Smart Array 6i 128Mb BBWC. It was shut down properly. It seems it was usual death for Proliant with ILO led 2,3,8 lighting. I want to move array to another identical server with same raid firmware level. What is the best strategy?: I have RAID 1+0 on bay 0 bay 1 bay 2 bay 3 As I understand bay0+bay1 are in RAID 1 , bay2+bay3 are in RAID 1, and both RAID 1 pairs are in RAID 0. So should I : Clear RAID config on new server, insert bay 0, bay 2 and power-on or Create RAID 1+0 with 1 logical volume from clear HDDs , and then poweroff ,remove HDDs and insert 2 HDDs(bay 0, bay 2) from old RAID 1+0. then power-on. (each hdd has its raid position info stored but may be could work on same config) According to documentation for Smart Array 6i it could be possible to migrate. however one requirement point is unclear for me Before you move drives, the following conditions must be met: • The array is in its original configuration. " What is orginal and non-original config for RAID 1+0? Another point "If you want to move an array to another controller, you must also consider the following additional limitations: • All drives in the array must be moved at the same time." I want to move one hdd from each RAID 1 pair. to have mirrors untouched just in case. Do they mean to move all 4 simultaniously? Smart Array 6i User Guide: Moving Drives and Arrays You can move drives to other ID positionson the same array controller. You can also move a complete arrayfrom one controller to another, even if the controllers are on different servers. Before you move drives, the following conditions must be met: • If moving thedrives to a different server, the new server must have enough empty bays to accommodate all the drives simultaneously. • The move will not result in more than 14 physical drives per controller channel. • No controller will be configured with more than 32 logical volumes. • The array has no failed or missing drives. • The array is in its original configuration. • The controller is not reading from or writing to any of the spare drives in the array. • The controller is not running capacity expansion, capacity extension, or RAID or stripe size migration. • The controller is using the latestfirmware version (recommended). If you want to move an array to another controller, you must also consider the following additional limitations: • All drives in the array must be moved at the same time. • In most cases, a moved array (and the logical drives that it contains) can still undergo arraycapacity expansion, logical drive capacity extension, or migration of RAID level orstripe size. When all the conditions have been met: Back up all data before removing any drives or changing configuration. This step is requiredif you are moving data-containing drives from a controller that does not have a battery-backed cache. Power down the system. If you are moving an array from a controller that contains a RAID ADG logical volume to a controller that does not support RAID ADG: Move the drives. Power up the system. If a 1724 POST message is displayed, drive positions were changed successfully and the configuration was updated. If a 1785 (NotConfigured)POST message is displayed: a. Power down the system immediately to prevent data loss. b. Return the drives to their original locations. c. Restore the data from backup, if necessary. Check the new drive configuration byrunning ORCA or ACU ("Configuring an Array" on page 9).

  Read the article

• Installing Ruby 1.9.3 OSX 10.7.4 breaks after altering PATH

  - by R V

  I was having trouble installing ruby 1.9.3-p194 from ruby 1.8.7 on my mac osx 10.7.4. I have was trying to fix my homebrew after running "brew doctor" and got the message of "/usr/bin occurs before /usr/local/bin This means that system-provided programs will be used instead of those provided by Homebrew. The following tools exist at both paths: c++-4.2 cpp-4.2 erb g++-4.2 gcc-4.2 gcov-4.2 gem i686-apple-darwin11-cpp-4.2.1 i686-apple-darwin11-g++-4.2.1 i686-apple-darwin11-gcc-4.2.1 irb rake rdoc ri ruby testrb" I fixed it by entering the following, which I found on another stackoverflow answer: export PATH="/usr/local/bin:/usr/local/sbin:~/bin$PATH" Lo and behold! when I typed that ruby updates to 1.9.3-p194. Ruby files seem to compile and run just fine. However, afterward, my navigation around terminal is messed up severely. For instance I can't do the command "open example_file.html" and have the file pop up in Chrome, instead I get the error: "-bash: open: command not found" Also, when I change directory, I get an error, inputting "$ cd desktop" yields the output, "-bash: dirname: command not found" but the directory does then changes... strange. When I exit out of a terminal window all this resets. I'm back to Ruby 1.8.7, have to use the PATH command again to update to 1.9.3, command line navigation gets broken again. Any guidance on how to remedy so I can use 1.9.3-p194 and also have normal terminal navigation would be greatly appreciated.

  Read the article

• centos TCP/IP connection very slow

  - by yuli chika

  I have a VSP (centos6.1 64bit) with 4gb ram. It always runs well, but in recent few days, the server become slowly. open a small css file need 22 seconds(2kb). tested in home/office/phone with (IE,chrome,safari,firefox). see in firebug networking DNS Lookup ?4?ms Connecting ?21.18?s Sending 1?ms Waiting ?115?ms Receiving ?9?ms The connection cost 21.18 seconds I have checked all the log file, there have no error. top commond, still have free memory. top - 00:23:15 up 8 days, 3:57, 1 user, load average: 3.60, 3.42, 3.83 Tasks: 221 total, 4 running, 217 sleeping, 0 stopped, 0 zombie Cpu(s): 19.3%us, 3.2%sy, 0.0%ni, 76.1%id, 1.4%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4194304k total, 3247724k used, 946580k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 32357 mysql 15 0 3710m 835m 6268 S 34.5 20.4 39:14.40 mysqld 9780 apache 15 0 442m 59m 12m S 33.2 1.4 0:05.69 httpd 9842 apache 15 0 403m 26m 10m S 16.9 0.7 0:01.23 httpd 9847 apache 15 0 412m 45m 22m R 15.3 1.1 0:01.00 httpd 9834 apache 15 0 426m 46m 11m R 13.0 1.1 0:02.22 httpd 9891 apache 15 0 407m 43m 19m S 8.0 1.1 0:00.33 httpd 9845 apache 15 0 414m 51m 24m S 6.0 1.3 0:01.53 httpd 9827 apache 15 0 402m 28m 11m S 3.3 0.7 0:02.69 httpd 9768 apache 16 0 414m 51m 24m S 3.0 1.3 0:06.51 httpd 9889 root 15 0 211m 12m 8160 S 2.7 0.3 0:00.32 php 9702 apache 15 0 415m 55m 26m S 1.7 1.4 0:10.67 httpd 9844 apache 15 0 413m 47m 21m S 1.7 1.2 0:01.21 httpd 9697 apache 15 0 414m 51m 24m S 1.3 1.3 0:11.05 httpd 9778 apache 15 0 414m 53m 25m S 1.3 1.3 0:05.38 httpd 9772 apache 15 0 414m 51m 23m R 0.7 1.3 0:05.04 httpd 9823 apache 15 0 415m 50m 23m S 0.7 1.2 0:03.97 httpd 9837 apache 15 0 402m 27m 11m S 0.3 0.7 0:01.04 httpd Then, how to check where is the problem and fixed it? I haven't change and config files in these days. Thanks.

  Read the article

• ASP.NET Web API returns 404 for PUT only on some servers

  - by Greg Bacchus

  Ok, I have been racking my brain and the internet for a solution to this. I just can't figure it out. I have written a site that uses ASP.NET MVC Web API and all working nicely until I put it on staging server. The site works fine on my local machine and the dev web server. Both dev and staging servers are Win Server 2008 R2. The problem is this: basically the site works, but there are some API calls that use the HTTP PUT method. These fail on staging returning a 404, but work fine elsewhere. The first problem that I came across and fixed was in Request Filtering. But still getting the 404. I have turned on tracing in IIS and get the following problem. 168. -MODULE_SET_RESPONSE_ERROR_STATUS ModuleName IIS Web Core Notification 16 HttpStatus 404 HttpReason Not Found HttpSubStatus 0 ErrorCode 2147942402 ConfigExceptionInfo Notification MAP_REQUEST_HANDLER ErrorCode The system cannot find the file specified. (0x80070002) The configs are the same on dev and staging, matter of fact the whole site is a direct copy. Why would the GETs and POSTs work, but not the PUTs? Thanks Greg

  Read the article

• Cannot login to ISCSI Target - hangs after sending login details

  - by Frank

  I have an ISCSI target volume, to which i am trying to connect using CentOS Linux server. Everything works fine, but cannot its stuck at login. Here are the steps i am performing: [root@neon ~]# iscsiadm -m node -l iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session20 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session21 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session22 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session23 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session30 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session31 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session78 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session79 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session80 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session81 Logging in to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) After this step, its stucks, waits for some time and then gives this output: Logging in to [iface: iface1, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) iscsiadm: Could not login to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260]. My iscsi.conf is this: node.startup = automatic node.session.timeo.replacement_timeout = 15 # default 120; RedHat recommended node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 5 node.session.err_timeo.abort_timeout = 15 node.session.err_timeo.lu_reset_timeout = 20 node.session.initial_login_retry_max = 8 # default 8; Dell recommended node.session.cmds_max = 1024 # default 128; Equallogic recommended node.session.queue_depth = 32 # default 32; Equallogic recommended node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 discovery.sendtargets.iscsi.MaxRecvDataSegmentLength = 32768 node.conn[0].iscsi.HeaderDigest = None node.session.iscsi.FastAbort = Yes Also, in access control, i have given full access to Any IP, Any CHAP user and fixed iscsi initiator name. With same access level, all other volumes on rest of servers are working, except this one.

  Read the article

• Error - "IR Hardware not detected" - but it's installed/working

  - by Robert

  I am trying to do: Settings-TV-Set up TV signal. During this process I am getting the error "IR Hardware not detected." With the remote, I can select the "try again" button (to re-detect) and it tries again, so the remote works. Plugging in the "IR blaster" doesn't change anything. (I wouldn't expect any difference, but I read a post which said you needed that. I will get Media Center to change channels if I can get that working - but first things first.) I was able to do the setup months ago when I had cable. and everything was fine. I just got DirecTV. (BTW - During the above process, Media Center detects the signal coming in on channel 3. Windows XP Media Center SP3. The TV Tuner card is a Pinnacle TCTV HD PCI. Everything - and I mean everything - has the latest firmware and drivers - as of 4 months ago when I fixed a different problem. So I DON"T WANT TO HEAR the standard answer to check drivers/firmware. THANK YOU.) Thanks for any help.

  Read the article

• Computer makes hissing noise, turns off after few seconds

  - by Kaustubh P

  I have a problem similar to the questions posted here and here. This is my config: Asus M3N78-EM, with AMD Phenom X3 720 2800 Black Edition, 4GB Transcend DDR2 RAM, Nvidia 9400GT. HD is a 160 GB IDE, and a LG IDE DVD-ROM. The power button is a bit off, I have removed the cover of the switch, and the only way it turns on is just giving the "stick" under the cover a gentle press. It turns on sometimes, and at other times, I have to cut-off the power from the PSU, and try again. I will describe my problem in as detail as possible, please bear with me: The problem has started in the last week, a few months after I changed the to the powerswitch arrangement as described above. The PC makes a hissing noise, and I wasn't able to pin-point the noise source, because of the various other fans. At first, removing the HD, rebooting w/o the HD, turning it off, reconnecting and booting made the problem go away. But of late, it doesn't happen. As suggested in the other questions, I tried reducing the load by disconnecting both the IDE drives, and the problem (noise + turn-off) still occurs. I also connected another 80G IDE HD,today morning, adn it still made that noise, and turned off. I also opened up the PSU, but I couldn't see any fault in that, I tried rotating the fan by blowing into the blades, and with my fingers, but the hissing noise didn't come from there. Or maybe the speed wasn't enough to evoke that noise. A few weeks ago: I had cleaned the Cabinet and had repasted the processor and its fan using some thermal paste. Could that be at fault? I also used a vacuum to blow the dust out of the PSU, could the power have been too much, to maybe offset the fan or something? A label on the PSU says it uses a ball-bearing fan. That only leaves me with the Processor fan and the processor itself. I didn't try removing the processor fan and processor from the motherboard, and then turning the PC on, fearing damage. Will doing so cause any damage? What can I do to localize and pin-point the problem? Also, after a few tries, the Computer starts up. Sometimes it turns of within 2 seconds, sometimes after the POST. Once it turned off at the grub. Another time it booted completely and then turned off. The only way to ensure that the PC wont turn off, is if the hissing noise stops. EDIT: I suspect it to be the Processor/Processor fan, owing to the source of noise. All the config, except for the Cabinet, is just over a year old. EDIT2: I also just remembered, that I had set the "On-power resume" to turn on, i.e. If I supply he PC with power, it will turn itself on, w/o me needing to press the switch. I had done that to workaround the faulty power-switch, as noted above. EDIT3: I calculated the power my system needs, from the antec site, and I just arrived at 292W

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• How to tell which process is hogging my CPU when they don't add up to 100%?

  - by endolith

  Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. The individual processes do not add up to 100%. I try killing lots of processes, but the overall usage continues to be 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, which is never anywhere near 100% CPU unless I'm doing something that requires it (like loading 32 Firefox tabs), after which it goes back to a normal idle level. It's not a new install or anything. There is no reason the processor should be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing every process, one at a time, until the problem went away, and killing vino-server finally fixed it, even though that process never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). But the question remains: How did a single process manage to use 100% CPU while top only showed that process at 5%? How do I identify culprits like this in the future? Looks like I'm not the only one who's had this problem: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

  Read the article

• Does NetworkSolutions have a good DNS service?

  - by joxl

  I'm recovering from a DNS disaster and I need some good advice on an alternate solution. My company owns a domain name through NetworkSolutions. Our website is hosted by another company who also maintains our DNS records. Our email is hosted by Google Apps, and the MX records are maintained through the afore-mentioned website/DNS host. Yesterday our website/DNS host had a serious hiccup in some software and completely overwrote all of our DNS records with invalid values; successfully pointing our domain and MX records at the wrong servers. Unfortunately it wasn't caught until it had time to significantly propagate. On top of that, it wasn't fixed until several hours later, combine that with a long TTL on the records; we have customers who are still bouncing emails. Anyhow, I am now completely terrified of this company's ability to do a good job, so I am considering switching to NetworkSolutions for our DNS service. I need the ability to configure A, CNAME, MX, and TXT records, preferably with a nice user interface (our current provider has a poor UI and doesn't support TXT records). Is NetworkSolutions a recommended DNS host? I am a little biased in their direction because the service will be free since we already pay them for our domain name. However I'm curious what others have experienced with their service.

  Read the article

• Cable management techniques

  - by cornjuliox

  How do you manage the giant jungle of cables behind your PC? When you have 2 or more PCs next to each other, you wind up with this giant mess cables that's a pain in the neck to clean especially when both computers are running 24/7 and any fidgeting with the cables is likely to cause data loss and/or angry users. So far I've tried masking tape, cable ties and plain old string but none have been very effective. The masking tape kept the cables in place, but over time they ended up leaving this awful sticky residue on the sides of the cables that just won't come off gets all over your fingers and is horrible horrible horrible. I have nightmares about that stuff. We used cable ties and 'folded' up some of the longer cables so that they weren't any longer than they needed to be, but this meant that the position of some of our devices like the keyboard and the mouse were essentially 'fixed' until we removed the ties. The string didn't work much differently and required that we tie them properly or risk it coming loose. I would switch to a wireless keyboard and mouse, but I don't want to have to deal with the added expense of batteries, even the rechargable ones. Plus I don't want them to die on me at a crucial moment (happened to me once while playing Firearms _<). How do large offices and data centers manage their masses of cable?

  Read the article

• Cable management techniques

  - by cornjuliox

  How do you manage the giant jungle of cables behind your PC? When you have 2 or more PCs next to each other, you wind up with this giant mess cables that's a pain in the neck to clean especially when both computers are running 24/7 and any fidgeting with the cables is likely to cause data loss and/or angry users. So far I've tried masking tape, cable ties and plain old string but none have been very effective. The masking tape kept the cables in place, but over time they ended up leaving this awful sticky residue on the sides of the cables that just won't come off gets all over your fingers and is horrible horrible horrible. I have nightmares about that stuff. We used cable ties and 'folded' up some of the longer cables so that they weren't any longer than they needed to be, but this meant that the position of some of our devices like the keyboard and the mouse were essentially 'fixed' until we removed the ties. The string didn't work much differently and required that we tie them properly or risk it coming loose. I would switch to a wireless keyboard and mouse, but I don't want to have to deal with the added expense of batteries, even the rechargable ones. Plus I don't want them to die on me at a crucial moment (happened to me once while playing Firearms _<). I know that there are people out there with home/office networks a thousand times more convoluted than mine, so

  Read the article

• OpenVPN (Tunnelblick) Suddenly Dropping Constantly

  - by Jeremy Privett

  I've been using Tunnelblick on my Mac for OpenVPN for about a year now. All of a sudden, this morning, it decided that it was going to take a nasty turn for the worse with no explanation. Here are the symptoms I'm seeing: I can connect to the VPN fine, initially. After about 2 - 5 minutes of no interruption, the connection suddenly dies. I can still see the VPN route using netstat -rn, and Tunnelblick believes it's still connected. No VPN traffic can go through and I can't even ping the VPN gateway. Eventually, Tunnelblick will catch on that the connection has died (usually about 5 - 10 minutes later) and shoot itself to restart and then the cycle starts over again. I've tried everything I can think of to figure this one out. I've completely flushed my system by rebooting and removing Tunnelblick and all traces of OpenVPN from my system and re-installing from scratch. No dice, same problem. I'm at my wits end, because I desperately need to get this fixed as the VPN is required for me to be able to do my job. Any ideas you have would be greatly appreciated.

  Read the article

• Accessing resources on localhost using domain credentials

  - by jas

  I'm trying to set up Team Foundation Server 2010, Sharepoint Server 2010 and Report Server 2008R2. I apologize for how long my question/problem is but I'm really lost on where to even look so am being as descriptive as possible in hopes that I'm making sense. The goal: Since developers can be inside or outside the firewall there needs to be a single http point of entry to TFS that works regardless of which side of the firewall you are and needs to work with external access to SharePoint and Report Server. Meaning we have it set up in DNS so buildserver.mydomain.com: points to the build service box which contains all of the services listed at the top of this post and specific services are defined/located by the port number. This is working great on every machine inside and out except for from the build server itself. All services must be able to work using external URLs. If I use http:// buildserver.mydomain.com:4800/tfs (the external URL) from my notebook which is behind the firewall I'm able to login with my domain credentials as expected. If the other developer points to the same URL from their home which isn't on the domain they are also able to login using their domain credentials. However if I am directly on buildserver and call SharePoint, TFS or Reporting Server from (i.e. http:// buildserver.mydomain.com:4800) itself using the external URL, I am prompted for a username and password. Entering my domain credentials results in another prompt to enter my credentials again. It will prompt three times regardless of which credentials are used (I have rights as a domain admin) and then after the third prompt directs me to a blank white page as though access was denied. There are no errors displayed on the page and nothing ends up in the event viewer. From buildserver if i use just the host name (the internal URL), then I'm prompted a single time for credentials and it works. i.e. http:// buildserver:4800/tfs works from the server itself. The behavior is identical for any service requiring authentication. Meaning from the box itself Sharepoint Central Admin, SharePoint WebApp, TFS, TFS Web Access, Report Server and Report Manager all fail using the external URL but will succeed if called using the interal URL. So the problem comes into play when configuring all of the services to work together. The only way to configure TFS is locally from the server which means I must point to the internal reporting server url (http:// buildserver:4800/reports and reportServer respectively instead of http:// buildserver.domainname.com:4800 like they need to be) since external URLs aren't working from itself. If I configure TFS to use the internal URL for Report Server then creating team projects or working in the SharePoint site for the team project fails for anyone not inside the domain since their machines have no idea who http:// buildserver:/reports even is or how to resolve them. I have configured Sharepoint with Alternate Access Mappings as well as set up Report Server to listen for external URLs. The external URLs simply aren't working when called from the server itself. I hope this makes sense. Thanks for taking the time to read this rather verbose plea for help.

  Read the article

• Annoying trackpad freeze on MacBook [solved]

  - by Hafthor

  NOTE: Question marked answered because it was forced after being put up for bounty. Actual solution was to have Apple repair it. Trackpad usually works, but sometimes stops responding for around 5 seconds and then suddenly starts working again. Seems to happen when I switch between typing and moving + button-clicking and also when I do a lot of double-clicking. Tried turning off the "Ignore accidental trackpad input". Apple replaced the keyboard/mouse under warranty. Problem remains. Any ideas? Edit: White non-unibody Late-2008 13" MacBook - fully up-to-date OS. Doesn't seem to matter if it is plugged in or not. Edit: Updated to Snow Leopard - seems to have made it worse. Edit: Applying even a little pressure to the left palm rest creates this condition. Apple replaced the top case again and this time it seems to have fixed it. Although, it looks like they may have added a spacer on the left palm rest to "fix" it.

  Read the article

• Burn .srt subtitles to AVC encoded video (transcoding with hardsubs) [closed]

  - by Saxtus

  Possible Duplicate: How do I hard code a movie with subtitles? I am looking for a software (or combination of software) that will allow me to hard burn subtitles from an .srt file, that has italics and bold typefaces, to an H.264/AVC encoded video so it can played from a desktop player that can't display external subtitles correctly. Ideally it could use Directshow as input as DirectVobSub makes nice job showing the subtitles as they should (allowing me to globally adjust font and size). CUDA use, to speed up encoding, will be great but not necessary. Video source is also H.264/AVC encoded. Audio is AC-3 5.1 and should be retained too but I have no problem re-muxin it later as long as it keeps synced. Until now I've unsuccessfully tested: Avisynth 2.58 Unable to make Direcvobsub to launch through it TextSub() command renders subtitles with fixed font/size and doesn't decode tags Malformed audio TMPGEnc 4.0 XPress 4.7.4.299 Audio downmixed to 2.0 Importing of subtitles doesn't decode tags Badaboom 1.2.1.7 No importing of subtitles at all SUPER © 2010.build.37 "Directshow decode" has similar effect as Avisynth above Other modes doesn't appear to allow any subtitles in Thank you.

  Read the article

• Windows 7 VPN Error 619

  - by TravisPUK

  So I am running Windows 7 Enterprise. This morning I was able to VPN using the built in VPN (Connect to Work Network etc). I had to change my network's IP address range and now the VPN will not work. It just stalls on the Verifying user name and password... message. But then it returns the 619 error. Anybody know why changing my machine's IP address would cause this problem? Where should I be looking to try and fix this issue? I have tried this on a Windows XP machine that also had the IP address range change and this still connects fine using exactly the same connection details. EDIT The internal network range changed from 192.x.x.x to 10.x.x.x. This was done on the entire Active Directory. All machines are running fine and the Windows XP machine, that works going to the same client VPN mentioned above is on the same network. Both the XP and the Win 7 machines are using DHCP served by the Domain Controller. The client domain is not performing any IP range checks/restrictions. The VPN is outside the internal network, connection is being made via the Internet and not passing through any other machine, other than the normal domain machines, ie DNS etc. This is passing through a router and the router has the relevant VPN passthrough options configured. All internal machines are working correctly with other forms of VPN, ie Cisco, Sonic etc (these were tested on other machines, they are not installed on the Vista or Win7 machines). After further testing, this is occurring on all Win7 and Vista machines where they can no longer connect to the client VPN, however all XP machines can still connect fine. This has been tested on three Vista, two Win7 and five XP machines. All machines are on DHCP and tests have been done with both the firewalls turned on and off, as well as with fixed IPs being used. Thanks Travis

  Read the article

• Google Apps Sync bloated PST file to 14GB

  - by James S

  Back story: I have Outlook connected to my Google Apps email and noticed that some mail never got migrated from my original PST file. I found some VBA code online that compares mail in different PST folders, modified it to find missing and copy those to the target folder. I ran it folder by folder and moved missing mail. Before the exercise the Google Apps PST was about ~4GB and after it was ~4.7GB. Problem: I left Outlook open so Google Sync can copy it online. 24 hours later the Google Apps PST file bloated to 14GB+ and none of the mail has been synced to the cloud. I know that there should be at most ~5GB of mail. Why is the rest of the space being taken up? Funny thing is Gmail shows 3GB as being used online. What I tried: I emptied the deleted items folder and recycling bin I've run Outlook compact PST and it didn't work. I tried SCANPST.exe on the PST and it didn't work. I re-ran compact PST and it didn't work (after SCANPST found and fixed a few errors) Any ideas out there on what caused the problem and how to solve it?

  Read the article

< Previous Page | 480 481 482 483 484 485 486 487 488 489 490 491  | Next Page >