Search Results

Search found 16096 results on 644 pages for 'top'.

Page 485/644 | < Previous Page | 481 482 483 484 485 486 487 488 489 490 491 492  | Next Page >

• Backup data rate on Raspberry Pi maxing out at 5 Mb/s. Why?

  - by bastibe

  I set up my Raspberry Pi as a Time Machine, as documented here. At the moment, the Raspberry Pi is connected to my MacBook Pro using a direct Ethernet cable. Also, an external hard drive (laptop drive) is connected to the Raspberry Pi using the USB port. However, backups are pretty slow. Activity Monitor claims that the Network is transferring a very steady 5 Mb/s, where my Time Capsule is transferring up to 8 Mb/s with a lot of fluctuation. The Raspberry Pi self-reports (top) that its CPU is only half-used, with about equal parts afpd, usb-storage and jbd2/sda1-8. Thus, I think that the processing power of the Raspberry Pi does not seem to be the problem here. To me, this looks like there is some kind of bottleneck that maxes out at 5 Mb/s thus potentially having my backups run at less than their potential speed. To the best of my knowledge, this might be the afp-daemon, the usb-bus or the external hard drive. So, my question is, how could I identify the true culprit and what can I do about it?

  Read the article

• Struggling to set-up NLB cluster

  - by Chris W

  I'm trying to set up NLB on a couple of Windows 2008 R2 virtual servers running on top of Hyper V R2. The servers each have a single vNIC for LAN access (and a second vNIC for SAN access). I'm setting up the cluster to use Multicast mode. The vNICs are each set to allow MAC spoofing. Essentially I'm finding that i can add SERVER1 as a host and it will pick up and respond to the cluster IP from a remote subnet. If I then 'stop' the node in NLB manager it still responds when I would expect it to stop answering on that IP. If I recreate the cluster and add SERVER2 as the first host, the wizard completes correctly and an IPCONFIG on the server shows that it now has the cluster IP but I can't ping the cluster IP from a remote subnet but I can from another machine on the same subnet. As a final test - with both servers in the cluster, pinging from another machine on the same subnet I still get a response from the cluster IP when both nodes are stopped according to the NLB manager. The two VMs are sat on the same physical blade and are built up exactly the same as they'll be used as SharePoint web front end servers. I'm at a loss as to what could be wrong with the second VM that prevents it taking on the address just as the sole node in the cluster, never mind the strange behaviour of the cluster when I stop/start nodes.

  Read the article

• Linux Scheduler (not using all cores on multi-core machine) RHEL6

  - by User512

  I'm seeing strange behavior on one of my servers (running RHEL 6). There seems to be something wrong with the scheduler. Here's the test program I'm using: #include <stdio.h> #include <unistd.h> #include <stdlib.h> void RunClient(int i) { printf("Starting client %d\n", i); while (true) { } } int main(int argc, char** argv) { for (int i = 0; i < 4; ++i) { pid_t p_id = fork(); if (p_id == -1) { perror("fork"); } else if (p_id == 0) { RunClient(i); exit(0); } } return 0; } This machine has a lot more than 4 cores so we'd expect all processes to be running at 100%. When I check on top, the cpu usage varies. Sometimes it's split (100%, 33%, 33%, 33%), other times it's split (100%, 100%, 50%, 50%). When I try this test on another server of ours (running RHEL 5), there are no issues (it's 100%, 100%, 100%, 100%) as expected. What's causing this and how can I fix it? Thanks

  Read the article

• Windows, never "lose focus" of the current window

  - by Mazura

  I want the task bar to light up orange and never lose focus to anything. If I'm installing something and then go play a game at some point it will drop out to the finished instillation. Also, if installing multiple programs at once my 'next' button can all of sudden become "click here to install this crappy toolbar" of another program's install. Of course there are settings for some programs to not "lose focus" or "stay on top" but I really want windows to handle it. If its somehow an exe called say, Taskswtich.exe, I could possibly use Process Blocker however I'm assuming its part of a function call or some such. For XP I found this: How to disable auto focus of opened Windows applications? but what about Windows7? And this old post Preventing applications from stealing focus with a bunch of long answers that say "no". I'd appreciate this not being merged with a 4 year old question. I'd like to avoid 3rd party software. This is 2014, don't we know how to hack windows yet?

  Read the article

• Why does USB thumb drive screw up boot sequence?

  - by Carl B

  I am looking for understanding to a boot issue. I have at times had some files and such that I save and retrieve from my thumb drive. I use the front panel as it is nice and easy to get to and I typically power down my system nightly. If I forget to pull the drive and power on the system, it becomes the first bootable device. As there is no OS on the USB Drive I get the BOOTMGR is missing press CTRL+ALT+DELETE. When I go into BIOS to see Boot sequence, there’s the thumb drive up top, DVD drive is missing and not found in the list of devices. All of the hard drives are next in line. When I pull the USB drive, and reboot, everything is back to normal. Old boot sequence is in place, DVD drive right where it should be and no issues. So why does this happen with a USB drive in port at boot up? If it can’t be booted from, shouldn’t the next drive be attempted? Note: This happens when the thumb drive is plugged into a USB port on the front panel. It does not seem to happen on rear panel ports.

  Read the article

• Need Routing help (tagged/untagged)

  - by TheCleaner

  I really need some help trying to figure some "basic" routing. My brain is fried from being sick for a week and I'm not thinking clearly. Picture below describes my "setup". I'm trying to accomplish routing a user from their workstation to the Juniper SSG520 and then "OUT" through the internet connection. I can't move the connection as it is physically located where the user's switch is. Here's what I CAN do at this point: I can ping from the Juniper SSG520 eth3/3 to 6x.xxx.253.116 from 6x.xxx.253.114 I can ping from the x450 in the top right to 6x.xxx.253.112 from 6x.xxx.253.116 What I CANNOT DO: I cannot ping from the SSG520 eth3/3 to 6x.xxx.253.112 from 6x.xxx.253.114 (basically from the Juniper box to the gateway. I've tried changing port 1 in the x450 VLAN 666 as tagged but when I do that then I can't even ping from the Juniper SSG520 eth3/3 to the VLAN on the x450 (6x.xxx.253.116). I need to route traffic out the eth3/3 interface on the SSG520 THROUGH the 2 x450 Switches and out the internet connection. The caveat is that the 2 x450 switches are connected via fiber over distance and have tagged VLANs in them for the routing. Thoughts? http://img251.imageshack.us/img251/7752/drawing1.jpg

  Read the article

• Hourly SQL Server 2005 Slowness (Possibly caused by SYSTEM)

  - by Zorlack

  We're trying to diagnose the cause of slowness on our Database server. We're running the latest rev SQL Server 2005 on Windows 2008x64. The behavior that we're seeing is this: We see the SYSTEM process spike one of the CPUs for about 2 minutes, during this time SQL server slows down by a factor of 10. The slowness lasts until SYSTEM is done, then in an hour everything starts again. During these slowdowns disk writes don't spike, paging doesn't spike, the only noticeable precursor we see is that SYSTEM maxes out one of the sixteen (HT)CPUs. Note that this doesn't happen at the top of the hour, it just happens once an hour, and it shifts a bit depending on the length of the incident. At the moment this is causing intermittent slowdowns, but when the server is really busy it can cause Worker Thread starvation. The server is a Dual Quad Dell R710 with 96GB of RAM and RAID10 data/log disks. Has anyone experienced this kind of problem? Does anyone know where we should look?

  Read the article

• Installing SilverStripe on 000webhost.com (Free web host)?

  - by benwad

  Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it brings me to a page with the following errors: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how.

  Read the article

• Win XP error 0x80041003 using GetObject/winmgmts

  - by John Lewis

  My computer is called "neil" and I want to set some values using WMI in vbScript. I adapetd the script below from one supplied by Microsoft. When I run it in my browser I get Error Type: (0x80041003) /dressage/30/pdf2.asp, line 8 I suspect it is some registry/security setting. Any advice? John Lewis FULL SCRIPT call Print_HTML_Page("http://neil/dressage/ascii.asp", "ascii") Sub SetPDFFile(strPDFFile) Const HKEY_LOCAL_MACHINE = &H80000002 strKeyPath = "SOFTWARE\Dane Prairie Systems\Win2PDF" strComputer = "." Set objReg=GetObject( _ "winmgmts:{impersonationLevel=impersonate}!\\" & _ strComputer & "\root\default:StdRegProv") strValueName = "PDFFileName" objReg.SetExpandedStringValue HKEY_LOCAL_MACHINE,_ strKeyPath,strValueName,strPDFFile End Sub Sub Print_HTML_Page(strPathToPage, strPDFFile) SetPDFFile( strPDFFile ) Set objIE = CreateObject("InternetExplorer.Application") 'From http://www.tek-tips.com/viewthread.cfm?qid=1092473&page=5 On Error Resume Next strPrintStatus = objIE.QueryStatusWB(6) If Err.Number 0 Then MsgBox "Cannot find a printer. Operation aborted." objIE.Quit Set objIE = Nothing Exit Sub End If With objIE .visible=0 .left=200 .top=200 .height=400 .width=400 .menubar=0 .toolbar=1 .statusBar=0 .navigate strPathToPage End With 'Wait until IE has finished loading Do while objIE.busy WScript.Sleep 100 Loop On Error Goto 0 objIE.ExecWB 6,2 'Wait until IE has finished printing WScript.Sleep 2000 objIE.Quit Set objIE = Nothing End Sub

  Read the article

• Script errors when run by launchd at startup, but not when run in Terminal

  - by Mechcozmo

  Hello. I'm attempting to create a RAM disk that loads the previous contents when the system starts up, and every six hours writes the contents to a disk image. Currently, when you run the script from the terminal ("sudo bash LogToRAM.sh") everything works fine. But when run from launchd during startup, it doesn't work. Here's the lines from the log; the first line just gives some idea as to where in the boot process we are: SecurityAgent[202] Showing Login Window com.mechcozmo.LogToRAM[51] + /Developer/usr/bin/SetFile -a V /Volumes/LogfileRAMdisk com.mechcozmo.LogToRAM[51] ERROR: File Not Found. (-43) on file: /Volumes/LogfileRAMdisk com.mechcozmo.LogToRAM[51] + /usr/sbin/asr -source '/Library/Application Support/LogToRAM/RAMdisk_store.dmg' -target /Volumes/LogfileRAMdisk/ -noverify Here is the script and plist file in question. Note that 'set -vx' is up at the top of the script; it give a lot of information about what is happening in the script. My current theory is that the /Volumes directory does not exist at this stage of the boot process, but that seems unlikely to be honest.

  Read the article

• Outlook 2007 font sizes

  - by Flack

  Hello, Something really strange seems to have happened to my Outlook 2007. Everything was working fine for a long time now but at the end of today, all of a sudden, all of the fonts in Outlook are messed up. The font size of mails I write is huge (I am not zoomed in) and the font sizes of the buttons are big too, specifically the "Send", "To", and "Cc" buttons. I tried changing the font sizes through Outlook, but some of the buttons on the "Mail Format" tab in Options are not working, mainly the "Stationary and Fonts" button. I hit it but no window opens. This is all happening on my x64 machine. I took a look at my x32 machine, which also has Outlook 2007 installed and everything is ok there. Below is a link to an image comparing the broken, large font Outlook (top of picture) and the normal, working outlook. The text in the mails I compose is also abnormally large in the broken Outlook. Big font Outlook buttons. Any ideas? This came out of no where after a few months of no problems. Thanks.

  Read the article

• reverse proxy not rewriting to https

  - by polishpt

  I need your help. I'm having problems with reverse proxy rewriting to https: I have an alfresco app running on top of tomcat and as a front and an Apache server - it's site-enabled looks like that: <VirtualHost *:80> ServerName alfresco JkMount /* ajp13_worker <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature Off </VirtualHost> I also have a reverse proxy server running on second machine and i want it to rewrite queries to https. It's site-enabled looks like that: <VirtualHost 192.168.251.50:80> ServerName alfresco DocumentRoot /var/www/ RewriteEngine on RewriteRule (.*) https://alfresco/ [R] LogLevel warn ErrorLog /var/log/apache2/alfresco-80-error.log CustomLog /var/log/apache2/alfresco-80-access.log combined ServerSignature Off </VirtualHost> <VirtualHost 192.168.251.50:443> ServerName alfresco DocumentRoot /var/www/ SSLEngine On SSLProxyEngine On SSLCertificateFile /etc/ssl/certs/alfresco.pem SSLCertificateKeyFile /etc/ssl/private/alfresco.key SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /alfresco http://192.168.251.50:8080/alfresco ProxyPassReverse /alfresco http://192.168.251.50:8080/alfresco LogLevel warn ErrorLog /var/log/apache2/alfresco-443-error.log CustomLog /var/log/apache2/alfresco-443-access.log combined ServerSignature Off </VirtualHost> Now, ProxyPass works, when I go to alfresco/alfrsco in a browser application opens, but rewriting to https doesn't work. Plese help. Regards when I go to 192.168.251.50 Tomcat configuration page shows up. When I go to 192.268.251.50:8080 - the same as above when I go to 192.168.251.50:8080/alfresco - alfresco app page shows app when I go to alfresco/alfresco - same as above when i go to https://alfresco or https://alfresco i get an error connecting to a server

  Read the article

• Windows XP seemingly out of resources but plenty of free RAM and swap available

  - by Artem Russakovskii

  This one has been bothering me for years and so far I couldn't find an adequate solution. The problem occurs on pretty much every XP install I've done. After opening a variety of programs or the system running existing programs for a while, Windows seemingly runs out of resources, without telling me. There's ALWAYS free RAM. For example, it just happened to me and I had over a gig of free RAM. There are no viruses, spyware, or other nonsense - it is a Windows resource problem, but the question is which resource is it running out of, how does one pinpoint it, and how does one prevent it? Sometimes, this happens after running specific programs - for example, today it happened when I started Photoshop CS4 and Flash CS4 at the same time. I also noticed that restarting The Bat (email client by Ritlabs) seems to get rid of this problem for a while but again, this happens on machines that don't even have The Bat installed. So what does exactly happen? The symptoms are: pressing alt-tab doesn't bring up the list anymore - it just jumps to the next window instantly, very similar to the way Alt-Esc works, however in this case, it's due to not having enough resources to bring up the alt-tab menu random programs would randomly crash, citing random errors, out of memory errors, system resources, inabilities to do system calls, etc. random programs would start missing random parts - for example, Firefox top menus might disappear, pull up partial selections, or not pull up anymore altogether. IE might lose a few of its toolbars. Some programs might fail to redraw or would just plain go gray where the UI used to be. Windows itself never complains about running out of RAM, virtual memory, or anything at all, yet it's running out of something. The only clue I was able to find and apply the fix today was this Desktop Heap Limitation. I haven't confirmed the fix working as not enough time passed. In the meantime, what are everyone's thoughts?

  Read the article

• X11 performance problem after upgrading from Centos3 to Centos5 with an ATI Rage XL

  - by Marcelo Santos

  After upgrading a computer from Centos3 to Centos5 an application that does a lot of scrolling took a very high performance hit. top tells me that X is using a lot of CPU and that was not happening before. The machine has an ATI Rage XL with 8MB and X is using the ati driver as there is no proprietary ATI driver for this board on linux. The xorg.conf: Section "Device" Identifier "Videocard0" Driver "ati" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "800x600" "640x480" EndSubSection EndSection Section "DRI" Group 0 Mode 0666 EndSection A similar machine that still has Centos3 installed is able to start DRI on the X server while this one is not, this is the Xorg.0.log for the Centos5 machine: drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed [drm] failed to load kernel module "mach64" (II) ATI(0): [drm] drmOpen failed (EE) ATI(0): [dri] DRIScreenInit Failed (II) ATI(0): Largest offscreen areas (with overlaps): (II) ATI(0): 1024 x 1279 rectangle at 0,768 (II) ATI(0): 768 x 1280 rectangle at 0,768 (II) ATI(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles Indirect CPU to Screen color expansion Solid Lines Offscreen Pixmaps Setting up tile and stipple cache: 32 128x128 slots 10 256x256 slots (==) ATI(0): Backing store disabled (==) ATI(0): Silken mouse enabled (II) ATI(0): Direct rendering disabled (==) RandR enabled I also tried using EXA instead of XAA and setting: Option "AccelMethod" "XAA" Option "XAANoOffscreenPixmaps" "true" uname -a Linux sir5.erg.inpe.br 2.6.18-128.7.1.el5 #1 SMP Mon Aug 24 08:20:55 EDT 2009 i686 i686 i386 GNU/Linux rpm -qa | grep xorg-x11-server xorg-x11-server-utils-7.1-4.fc6 xorg-x11-server-sdk-1.1.1-48.52.el5 xorg-x11-server-Xvfb-1.1.1-48.52.el5 xorg-x11-server-Xnest-1.1.1-48.52.el5 xorg-x11-server-Xorg-1.1.1-48.52.el5 The drmOpenDevice error continues when using the suggested Option "AIGLX" "true".

  Read the article

• Compiled ruby fails to find curses

  - by Hamish Downer

  I'm attempting to install the sup MUA but I'm having trouble. When I try to run it, it can't find curses: /usr/local/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `gem_original_require': no such file to load -- curses (LoadError) ... I am installing on a server running CentOS 5. I have compiled ruby and rubygems from source, and then installed sup using rubygems. I followed this article to compile ruby. I have found having a similar problem on ubuntu. The fix suggested there is to install libcurses-ruby, but I can't find a similarly named package in CentOS. I have installed the ncurses-devel package, as that was required for installing sup using gem. I have also installed the ncurses, cursesx and rbcurse gems, but none of these have fixed the problem. The article above about compiling ruby said you had to recompile the zlib extension, after doing: cd ext/zlib sudo ruby extconf.rb --with-zlib-include=/usr/include --with-zlib-lib=/usr/lib cd ../.. sudo make sudo make install So I've tried a few variants in ext/curses. The top few lines of ext/curses/extconf.rb are require 'mkmf' dir_config('curses') dir_config('ncurses') dir_config('termcap') So I've tried a few variants of setting paths: sudo ruby extconf.rb --with-curses-include=/usr/include --with-curses-lib=/usr/lib --with-ncurses-include=/usr/include --with-ncurses-lib=/usr/lib --with-termcap-lib=/lib sudo ruby extconf.rb --with-curses-include=/usr/include --with-curses-lib=/usr/lib --with-termcap-lib=/lib and re-doing the make, but to no avail as yet. Any ideas to move it forward are welcome.

  Read the article

• Automated software installation for MS Windows?

  - by Duncan Bayne

  I am currently setting up a Windows development environment (the whole Visual Studio 2010 stack plus plugins on top of Windows 7). This has got me wondering whether there's a Windows equivalent to what I do for dev environment setup in Ubuntu. It takes literally hours to get a dev environment set up in Windows, involving a lot of manual intervention. On Ubuntu, I have two shell scripts - one I run as root which configures the system using apt-get (amongst other things), one I run as me which configures my user account. Those scripts live in my private Subversion repository. To set up a dev environment from scratch requires five commands: sudo apt-get install -y subversion svn co http://svn.XXXX.XXX/personal/ cd personal sudo ./ubuntu_setup_root.sh ./ubuntu_setup_user.sh The only human intervention required is to pick a root password for MySQL. So it takes only a few minutes of human attention to go from a vanilla Ubuntu installation to a full development environment with the latest builds of everything, perfectly tailored down to shortcut keys and wallpaper. Is there an equivalent process for Windows? In an ideal world it'd be something trivially scriptable using C# Script or Powershell, which could live in source control & make use of a repository of ISOs downloaded from MSDN ...

  Read the article

• Ubuntu Server mdadm drbd ocfs2 kvm hangs under heavy file reading

  - by Stefano Annese

  I have deployed four ubuntu 10.04 server. They are coupled two by two in a cluster scenario. on both sides we have software raid1 disks, drbd8 and OCFS2 and on top of it some kvm machines run with qcow2 disks. I followed this: Link corosync is just used for DRBD and OCFS, the kvm machines are run "manually" When it works is fine: good performances, good I/O, but at a given time one of the two cluster started hanging. Then we tried with just one server turned on and it hangs the same. It seems to happen when an heavy READ in one of the virtual machines occurs, that is during rsyn backup. When the fact occurs the virtual machines are not reachable any more and the real server responds with good delay to the ping but no screen and no ssh is available. All we can do is force shutdown (hold the button) and restart and when it turns on again the raid on which relay drbd is resyncing. All the time it hangs we see such fact. After a couple of week of pain on one side this morning also the other cluster hung, but it has different moteherboard, ram, kvm instances. What is similar is reading for rsync scenario and Western Digital RAID Edistion disks on both side. Can anybody give me some input to solve such issue?

  Read the article

• Excel 2007: Named ranges problems when linking workbooks

  - by Mike

  I've 30+ workbooks each with 5 specific worksheets (formated the same). Each worksheet's data needs to be linked to a master workbook, so that I end up with 5 master workbooks and all the specific data in one long table format $A$2:$I$750. (Are you still with me? ;)) I don't have access to a database, so I'm having to link the sheets to their master workbook directly. I've highlighted the data I need; named the range; and then tried referencing this from my master workbook. I get the #Value error symbol when I try to link (=[WorkbookName]!MyNamedRange) to a cell that doesn't match the top left cell of my range. Example: MyNamedrange is always =$A$2:$I43$ on one specific sheet. On my master workbook it works if it's referenced at A2 but I get #Value if it's referenced A1, or A44. Any ideas? I'm trying to link my data in one continous table so I can run a pivot on it, and other things. Can it be done like this, or should I just copy and paste? I'm trying to keep things 'linked'so I do not need to spend time C&Ping all day. Many thanks Mike.

  Read the article

• setting up git on cygwin - openssl

  - by user23020

  I'm trying to get git running in cygwin on a windows 7 machine I have git unpacked and the directory git-1.7.1.1 when i run make install from within that directory, I get CC fast-import.o In file included from builtin.h:4, from fast-import.c:147: git-compat-util.h:136:19: iconv.h: No such file or directory git-compat-util.h:140:25: openssl/ssl.h: No such file or directory git-compat-util.h:141:25: openssl/err.h: No such file or directory In file included from builtin.h:6, from fast-import.c:147: cache.h:9:21: openssl/sha.h: No such file or directory In file included from fast-import.c:156: csum-file.h:10: error: parse error before "SHA_CTX" csum-file.h:10: warning: no semicolon at end of struct or union csum-file.h:15: error: 'crc32' redeclared as different kind of symbol /usr/include/zlib.h:1285: error: previous declaration of 'crc32' was here csum-file.h:15: error: 'crc32' redeclared as different kind of symbol /usr/include/zlib.h:1285: error: previous declaration of 'crc32' was here csum-file.h:17: error: parse error before '}' token fast-import.c: In function `store_object': fast-import.c:995: error: `SHA_CTX' undeclared (first use in this function) fast-import.c:995: error: (Each undeclared identifier is reported only once fast-import.c:995: error: for each function it appears in.) fast-import.c:995: error: parse error before "c" fast-import.c:1000: warning: implicit declaration of function `SHA1_Init' fast-import.c:1000: error: `c' undeclared (first use in this function) fast-import.c:1001: warning: implicit declaration of function `SHA1_Update' fast-import.c:1003: warning: implicit declaration of function `SHA1_Final' fast-import.c: At top level: fast-import.c:1118: error: parse error before "SHA_CTX" fast-import.c: In function `truncate_pack': fast-import.c:1120: error: `to' undeclared (first use in this function) fast-import.c:1126: error: dereferencing pointer to incomplete type fast-import.c:1127: error: dereferencing pointer to incomplete type fast-import.c:1128: error: dereferencing pointer to incomplete type fast-import.c:1128: error: `ctx' undeclared (first use in this function) fast-import.c: In function `stream_blob': fast-import.c:1140: error: `SHA_CTX' undeclared (first use in this function) fast-import.c:1140: error: parse error before "c" fast-import.c:1154: error: `pack_file_ctx' undeclared (first use in this functio n) fast-import.c:1154: error: dereferencing pointer to incomplete type fast-import.c:1160: error: `c' undeclared (first use in this function) make: *** [fast-import.o] Error 1 I'm guessing that most of these errors are due to the iconv.h and openssl files which apparently are missing, but I can't figure out how I'm supposed to install those (if I am), or if there is some other way to get around this.

  Read the article

• SSH traffic over openvpn connection freezes when I cat a file

  - by user42055

  I have an openvpn (version 2.1_rc15 at both ends) connection setup between two gentoo boxes using shared keys. it works fine for the most part. I use mysql, http, ftp, scp over the vpn with no problems. But when I ssh from the client to the server over the vpn, weird things happen. I can login, i can execute some commands. But if i try to run an ncurses application like top, or i try to cat a file, the connection will stall and I'll have to sever the ssh session. I can, for example, execute "echo blah; echo .; echo blah" and it will output the three lines of text over the ssh session fine. But if i execute "cat /etc/motd" the session will freeze the moment I press enter. I compiled openvpn 2.1.1 on my mac and copied over my config directory from my gentoo client. The mac connected and ssh sessions worked fine without freezing. I then compiled it on my older gentoo box (2.6.26 kernel) which I am retiring due to a dying hard drive, and ssh over it also works perfectly. Why does it fail on my brand new gentoo box ? I've tried compiling three different kernels in case it was that, but other than that there should be no difference between my older and my newer gentoo boxes that I can think of. Any suggestions on what's wrong ?

  Read the article

• Ubuntu lucid, maverick high iowait

  - by netom

  I'm using Ubuntu, and I've got the same problem with Lucid and Maverick. From time to time, especially a few minutes after boot, the iowait goes between 50-100% and the box is unusable. Everything that tries to access the disk freezes. I have the following setup: Hard disk: Model Family: Western Digital Caviar Green family Device Model: WDC WD15EADS-00P8B0 Serial Number: WD-WMAVU0391287 Firmware Version: 01.00A01 User Capacity: 1.500.301.910.016 bytes I have a quad core Intel Core2 Q6600 processor, and 4G of memory. When the high iowait occurs, usually 4 processes are active: kdmflush (two procs) jbd2/dm-0-8 jbd2/db-1-8 and a few more starving user processes of course. I know this from top and iotop. Any suggestions about why this is happening? There are a lot of q/a-s about linux and high iowait, but none of them helped so far, I even tweaked the hard disk not to park the head in every 8 seconds (Load cycle count is 50334!!!!! :o ), but nothing. Problem persists. Thank you in advance.

  Read the article

• Spots appear in a rectangle area on screen, ubuntu gnome 13.04, nvidia driver

  - by frozen-flame

  I am using Ubuntu Gnome 13.04 with nvidia-310 driver installed. My GPU is GeForce GTX650. Strange spots freqently appear on screen, with following traits: Spots are restricted in one or two rectangle areas at any instant. When typing, the pattern of spots change. Possibly increase, or all disappear when one key pressed. Mouse movement also influences. This problem last within one boot. The only way can I get rid of this problem is to reboot. It can be detected as soon as entering desktop if it appears. Simultaneously, the "power off" option is lost in the top-right menu of Gnome3. Never such problem when using windows 7 on the same computer, neither ubuntu with Nouveou driver. Seldomly, half of the screen become black. I googled a lot. Similar conditions are described, but no confirmed solution. Uninstall-r einstall strategy does not work. Any clue solving this will be appeciated.

  Read the article

• Home media storage solution

  - by Dan

  I record lots of personal HD film footage and am looking for a cheap way to store all of this. I take ~120 GB of footage each month, so something expandable would be nice... something that might be able to hold 6+ SATA drives. There is a low load requirement, as there is never more than a user or two... but it should be able to keep up with streaming 2 simultanious HD videos. I don't really want to spend more than $200-$300 on top of the $900 I am thinking of spending for 6X2GB SATA drives@ $150 apiece, but I am willing to pay extra for a quality solution. Should I get a cheap NAS server? a cheap multi-drive external enclosure? should I just get some used systems off craigslist? If it is an independent system I'll probably just throw ubuntu on it since I can maintain that well. Its easy to do a software raid from ubuntu too, if I choose to go that way. Thanks

  Read the article

• Architecture for highly available MySQL with automatic failover in physically diverse locations

  - by Warner

  I have been researching high availability (HA) solutions for MySQL between data centers. For servers located in the same physical environment, I have preferred dual master with heartbeat (floating VIP) using an active passive approach. The heartbeat is over both a serial connection as well as an ethernet connection. Ultimately, my goal is to maintain this same level of availability but between data centers. I want to dynamically failover between both data centers without manual intervention and still maintain data integrity. There would be BGP on top. Web clusters in both locations, which would have the potential to route to the databases between both sides. If the Internet connection went down on site 1, clients would route through site 2, to the Web cluster, and then to the database in site 1 if the link between both sites is still up. With this scenario, due to the lack of physical link (serial) there is a more likely chance of split brain. If the WAN went down between both sites, the VIP would end up on both sites, where a variety of unpleasant scenarios could introduce desync. Another potential issue I see is difficulty scaling this infrastructure to a third data center in the future. The network layer is not a focus. The architecture is flexible at this stage. Again, my focus is a solution for maintaining data integrity as well as automatic failover with the MySQL databases. I would likely design the rest around this. Can you recommend a proven solution for MySQL HA between two physically diverse sites? Thank you for taking the time to read this. I look forward to reading your recommendations.

  Read the article

• Apache Process question about RAM usage

  - by Andrew Fashion

  So everytime I load a new page, I notice a new HTTPD process opens, every time I click a page, and each process says it's using anywhere from 2-4.5% of memory. Does that mean every single process is running at that time using 2-4% of RAM? It's a brand new server and I'm the only one on the server at the moment. Or does it mean all the other processes are dying, and only the new one is active. Because 4% of my 2048MB of RAM is already 82MB for just one process!?!? Let me know, because I am trying to determine what I need to beef my server up in order to handle high loads of traffic. I'm expect to get 20,000 uniques per day on launch. I am currently running a Dual Quad Xeon server, with only 2GB of ram, I will upgrade to 8GB or more shortly. Let me know what you suggest! thank you [root@D18634 log]# top | grep 'httpd' 11315 apache 15 0 362m 82m 24m R 12.3 4.1 0:03.00 httpd 11310 apache 16 0 322m 41m 21m S 5.7 2.1 0:02.98 httpd 11315 apache 15 0 362m 83m 25m S 24.3 4.1 0:03.73 httpd 11319 apache 16 0 324m 42m 20m R 1.0 2.1 0:01.85 httpd 11319 apache 16 0 362m 82m 23m R 78.5 4.1 0:04.21 httpd 11321 apache 16 0 323m 44m 23m S 35.3 2.2 0:04.13 httpd 11319 apache 15 0 361m 82m 23m S 8.3 4.1 0:04.46 httpd 11321 apache 15 0 323m 44m 23m S 35.9 2.2 0:05.21 httpd 11313 apache 15 0 324m 41m 19m S 48.6 2.1 0:03.23 httpd 11322 apache 16 0 354m 72m 20m R 11.0 3.6 0:05.11 httpd 11322 apache 16 0 354m 72m 20m S 23.9 3.6 0:05.83 httpd 11314 apache 16 0 355m 75m 22m R 18.3 3.7 0:04.64 httpd

  Read the article

< Previous Page | 481 482 483 484 485 486 487 488 489 490 491 492  | Next Page >