Search Results

Search found 16096 results on 644 pages for 'top'.

Page 489/644 | < Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >

  • apache httpd.conf - virtualhost configuration

    - by Adam
    I'm new to apache and httpd.conf The problem I'm having is I need different website to go to different vhost configs and if only the IP is requested it needs to go to the root index.html This works fine for the virtualhosts: <VirtualHost *:80> DocumentRoot /var/www/html/bali-accommodation.co ServerName www.bali-accommodation.co </VirtualHost> <VirtualHost *:80> DocumentRoot /var/www/html/balibeach.co ServerName www.balibeach.co </VirtualHost> <VirtualHost *:80> DocumentRoot /var/www/html/dating-website.co ServerName www.dating-website.co </VirtualHost> However when I just specify the IP it does to www.XXX.XXX.XXX.XXX (appends the www). I know in the websites there is a .htaccess redirect that adds the www but I didn't want the IP to go into the vhosts config. I tried adding this to the top of the Vhost config: <VirtualHost *:80> DocumentRoot /var/www/html ServerName localhost </VirtualHost> with above it shows the index.html perfectly but all the websites go into this catch all. I've also tried this for the websites vhosts: DocumentRoot /var/www/html/bali-accommodation.co ServerName www.bali-accommodation.co I've tried the above with and without the 'www' in the first line unsuccessfully. Is there a way to have the vhosts work for the domains and if someone just enters the IP it goes to the root index.html? /var/www/html/index.html? thankyou so much Adam

    Read the article

  • How do I Install Intermediate Certificates (in AWS)?

    - by getmizanur
    I have installed private key (pem encoded) and public key certificate (pem encoded) on Amazon Load Balancer. However, when I check the SSL with site test tool, I get the following error: Error while checking the SSL Certificate!! Unable to get the local issuer of the certificate. The issuer of a locally looked up certificate could not be found. Normally this indicates that not all intermediate certificates are installed on the server. I converted crt file to pem using these commands from this tutorial: openssl x509 -in input.crt -out input.der -outform DER openssl x509 -in input.der -inform DER -out output.pem -outform PEM During setup of Amazon Load Balancer, the only option I left out was certificate chain. (pem encoded) However, this was optional. Could this be cause of my issue? And if so; How do I create certificate chain? UPDATE If you make request to VeriSign they will give you a certificate chain. This chain includes public crt, intermediate crt and root crt. Make sure to remove the public crt from your certificate chain (which is the top most certificate) before adding it to your certification chain box of your Amazon Load Balancer. If you are making HTTPS requests from an Android app, then above instruction may not work for older Android OS such as 2.1 and 2.2. To make it work on older Android OS: go here click on "retail ssl" tab and then click on "secure site" "CA Bundle for Apache Server" copy and past these intermediate certs into certificate chain box. just incase if you have not found it here is the direct link. If you are using geo trust certificates then the solution is much the same for Android devices, however, you need to copy and paste their intermediate certs for Android.

    Read the article

  • SQLSTATE[HY000]: General error: 2006 MySQL server has gone away

    - by Barkat Ullah
    Server details: RAM: 16GB HDD: 1000GB OS: Linux 2.6.32-220.7.1.el6.x86_64 Processor: 6 Core Please see the link below for my # top preview: I can often see the error mentioned in title in my plesk panel and my /etc/my.cnf configuration are as below: bind-address=127.0.0.1 local-infile=0 datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql max_connections=20000 max_user_connections=20000 key_buffer_size=512M join_buffer_size=4M read_buffer_size=4M read_rnd_buffer_size=512M sort_buffer_size=8M wait_timeout=300 interactive_timeout=300 connect_timeout=300 tmp_table_size=8M thread_concurrency=12 concurrent_insert=2 query_cache_limit=64M query_cache_size=128M query_cache_type=2 transaction_alloc_block_size=8192 max_allowed_packet=512M [mysqldump] quick max_allowed_packet=512M [myisamchk] key_buffer_size=128M sort_buffer_size=128M read_buffer_size=32M write_buffer_size=32M [mysqlhotcopy] interactive-timeout [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid open_files_limit=8192 As my server httpd conf is set to /etc/httpd/conf.d/swtune.conf and the configuration is as below: at prefork.c: <IfModule prefork.c> StartServers 8 MinSpareServers 10 MaxSpareServers 20 ServerLimit 1536 MaxClients 1536 MaxRequestsPerChild 4000 </IfModule> If I run grep -i maxclient /var/log/httpd/error_log then I can see everyday this error: [root@u16170254 ~]# grep -i maxclient /var/log/httpd/error_log [Sun Apr 15 07:26:03 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting [Mon Apr 16 06:09:22 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting I tried to explain everything that I changed to keep my server okay, but maximum time my server is down. Please help me which parameter can I change to keep my server okay and my sites can load fast. It is taking too much time to load my sites.

    Read the article

  • Free software for backing up an attached network drive

    - by Richard
    My wireless router comes with a USB connector which allows me to plug an external hard drive in and it'll act as a Network Attached Storage. The problem is that I want to backup this hard-drive to the external drive of another computer so that if the NAS drive fails, I don't lose everything. However, Windows 7 Backup refuses to include the NAS as a location to backup. I can't fool it by mapping it to a drive letter either. Google presents lots of pages on how to backup files to a NAS, but not the other way around. Can anyone advise me on free software which can do incremental backups of a NAS drive to an external drive attached the computer it is running on? I'm aware of this question but the top answers have one or more of the following issues: They aren't free. The free version cannot backup a NAS. They cannot do incremental backups. They're just a script and therefore have limited other functionality (eg. disk space management, scheduling, compression, etc.etc.)

    Read the article

  • Python module: Trouble Installing Bitarray 0.8.0 on Mac OSX 10.7.4

    - by Gabriele
    I'm new here! I have trouble installing bitarray (vers 0.8.0) on my Mac OSX 10.7.4. Thanks! ('gcc' does not seem to be the problem) Last login: Sun Sep 9 22:24:25 on ttys000 host-001:~ gabriele$ gcc -version i686-apple-darwin11-llvm-gcc-4.2: no input files host-001:~ gabriele$ Last login: Sun Sep 9 22:18:41 on ttys000 host-001:~ gabriele$ cd /Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/bitarray-0.8.0/ host-001:bitarray-0.8.0 gabriele$ python2.7 setup.py installrunning install running bdist_egg running egg_info creating bitarray.egg-info writing bitarray.egg-info/PKG-INFO writing top-level names to bitarray.egg-info/top_level.txt writing dependency_links to bitarray.egg-info/dependency_links.txt writing manifest file 'bitarray.egg-info/SOURCES.txt' reading manifest file 'bitarray.egg-info/SOURCES.txt' writing manifest file 'bitarray.egg-info/SOURCES.txt' installing library code to build/bdist.macosx-10.6-intel/egg running install_lib running build_py creating build creating build/lib.macosx-10.6-intel-2.7 creating build/lib.macosx-10.6-intel-2.7/bitarray copying bitarray/__init__.py -> build/lib.macosx-10.6-intel-2.7/bitarray copying bitarray/test_bitarray.py -> build/lib.macosx-10.6-intel-2.7/bitarray running build_ext building 'bitarray._bitarray' extension creating build/temp.macosx-10.6-intel-2.7 creating build/temp.macosx-10.6-intel-2.7/bitarray gcc-4.2 -fno-strict-aliasing -fno-common -dynamic -isysroot /Developer/SDKs/MacOSX10.6.sdk -arch i386 -arch x86_64 -g -O2 -DNDEBUG -g -O3 -I/Library/Frameworks/Python.framework/Versions/2.7/include/python2.7 -c bitarray/_bitarray.c -o build/temp.macosx-10.6-intel-2.7/bitarray/_bitarray.o unable to execute gcc-4.2: No such file or directory error: command 'gcc-4.2' failed with exit status 1 host-001:bitarray-0.8.0 gabriele$

    Read the article

  • How to organise storage for media content such as video and music?

    - by thor
    Currently, we have a single server hosting all content: music, video and software. This content is downloaded by users through HTTP. Now free space is coming to an end and we are exploring different ways of extending our storage capacity. We want to do it cheap, simple and reliable (protected from disk/ server faults). Currenly, we see two ways: Add a couple of cheap servers with 4 disks (RAID1 ?), run some distributed file-system on top, like GlusterFS. Pros: hopefully, we will see all our disks as single flat file system, just dump content into it and be done. Cons: could be tricky in configuration and handling of faults. Add a couple of cheap servers, all running HTTP servers. Each piece of content (be it a music file or video) is placed on randomly selected two servers. Pros: don't have to deal with RAID, as content is duplicated; single server failure does not bring down any part of content; doubled distribution capacity (as any signle file could be downloaded from any of two servers hosting it). Cons: requires some scripting on part of distribution of content, adding/ removing servers. Do we miss any other ways? Which of the aforementioned options seems to be the best?

    Read the article

  • Typing Japanese on Windows Vista with Dvorak

    - by Ken
    I'm using Windows Vista, and I type English with the Dvorak keyboard layout, and I want to be able to type Japanese text that way, too. I've figured out how to set it up to let me type Japanese here, but it uses QWERTY. What I've got so far is: click the "EN" in the taskbar, and select "JP" if the letter that appears in the taskbar is "A", hit alt-~ to change it to "?" type as if I was typing Romaji on a QWERTY keyboard, (e.g., left pinky home row, right ring finger top row), and hiragana appear (??) press spacebar to convert to kanji (e.g., ?), and return to accept That all works great, but it assumes I'm on QWERTY, which isn't very comfortable for me. I want everything the same, but to be able to type kana with Dvorak (e.g., left pinky home row, left ring finger home row - ??). I can do this on Mac OS, so it's not an unheard-of feature. But it was kind of an obscure setting to find, so I figure on Windows it's probably a really obscure setting. :-) But I haven't been able to find it yet. Thanks!

    Read the article

  • What was SPX from the IPX/SPX stack ever used for?

    - by Kumba
    Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

    Read the article

  • Why is my apache2, mod_fcgid, php configuration causing 100% cpu usage?

    - by Scott Lundgren
    Page load makes a quick initial connection, then hangs about 10 seconds before the page renders. When the server load goes up I start watching top & I see that both CPUs get pegged at times to 100% by between 4-8 processes of php-cgi. My theory is that since I never see RAM usage never go above 50%, that apache is able to handle the requests coming in, but is queueing them for PHP to process. What is wrong with my mod_fcgid/php configuration ? RHEL 5.4 2 Xeon E5420s @ 2.50 Ghz 4 Gb RAM Apache 2.2.3 Timeout 30 KeepAlive On MaxKeepAliveRequests 0 KeepAliveTimeout 5 <IfModule worker.c> StartServers 2 MaxClients 300 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> mod_fcgid 2.2.10 LoadModule fcgid_module modules/mod_fcgid.so <IfModule !mod_fastcgi.c> AddHandler fcgid-script fcg fcgi fpl php </IfModule> SocketPath run/mod_fcgid SharememPath run/mod_fcgid/fcgid_shm DefaultInitEnv PHPRC "/etc/" FCGIWrapper /usr/bin/php-cgi .php MaxRequestsPerProcess 1500 MaxProcessCount 20 IPCCommTimeout 240 IdleTimeout 240 APC 3.0.19 extension = apc.so apc.enabled=1 apc.shm_segments=1 apc.optimization=0 apc.shm_size=32 apc.ttl=7200 APC cache is 43% used with a 99% hit rate

    Read the article

  • VMware NAS/iSCSI recommendations - smallish organization

    - by Bubnoff
    I have two VMware servers - ESX + ESXi. Two backup NAS boxes. The current NAS boxes are low-cost and unsuitable for running VMs from. Support NFS only. Slow. My plan is to have a dedicated iSCSI/NAS for storing and running VMs. Two additional low-cost boxes for backup. I'm looking for advice regarding 2 things really: Recommendations as far as VMware architecture/design for a smaller organization. Less than 20 Virtual Machines. 2 servers + 2 x 1.5 terabyte backup NAS boxes. A good NAS/iSCSI box with your recommendation on RAID config ...I would go with 6 or better. I'm trying to design an installation that is both fast and reliable/redundant. If you have any experiences to share or your current configuration including network design ( switches, fiber ...etc ), I will be enormously thankful. I'm not married to this idea, so if you have a design not using iSCSI NAS boxes ...let er rip. Cost? Can we stay around $5,000 ( on top of already stated components )? Links to info are welcome also. Thanks for reading! Bubnoff

    Read the article

  • Search behavior of Windows 7 start menu

    - by Kevin Ivarsen
    I'm coming to Windows 7 from XP, and there are aspects of the start menu search that I like. However, there are some behaviors that seem either inconsistent or surprising to me. For example: If I type "Pa" into the search bar, Paint is the first result (under the "Programs" heading), and it is selected for me. I can just hit Enter to start the program If I have a standalone exe "testing" on my desktop, and I type "test", the program comes up as the first item (under the "Files" heading), but it is not selected for me. I have to hit down-down-down-enter to open it from the keyboard. The same appears to be true for shortcuts and folders. What classifies something as a "Program" verses a "File"? Is there any way to configure the start menu so that the first search result is always selected? As a heavy keyboard user, it seems insane for the behavior to be inconsistent, and to require so many keypresses to select the top result. Also, are there resources that document the details, limitations, and tricks of the start menu search? (For example, a "Proc Exp" search will match "Process Explorer", but not "ProcessExplorer") EDIT: I've found that instead of hitting down-down-down to select the first item (when no Programs are in the list), you can just hit tab. This helps a bit, but the inconsistent behavior still makes this search feature more awkward and frustrating than necessary.

    Read the article

  • MySQL consuming all system memory on INSERT ... SELECT

    - by siete
    The mysql daemon is getting killed because Linux is reaching out of memory: Oct 24 07:41:23 <hostname> kernel: [82297.673701] Out of memory: kill process 13816 (mysqld) score 1839626 or a child There is a link with some workaround on this. That only happen when executing a query INSERT ... SELECT with a very huge resulset. MySQLTuner script displays that maximum theorical memory is less than 8GB, but top and munim shows that is getting over all RAM and swap available: [--] Total buffers: 560.0M global + 72.2M per thread (100 max threads) [OK] Maximum possible memory usage: 7.6G (43% of installed RAM) I'm tried to tune some options with not results, there are the relevant ones: skip-locking max_connections = 100 key_buffer_size = 512M max_allowed_packet = 32M table_open_cache = 2000 open_files_limit = 3000 sort_buffer_size = 16M read_buffer_size = 16M read_rnd_buffer_size = 8M myisam_sort_buffer_size = 64M thread_cache_size = 4 query_cache_size = 16M query_cache_limit = 2M thread_concurrency = 4 join_buffer_size = 32M tmp_table_size = 32M max_heap_table_size = 32M query_cache_limit = 8M bulk_insert_buffer_size = 64M myisam_max_sort_file_size = 50GB myisam_mmap_size = 10GB And there is a system resume: OS: Linux Debian "Squeeze" 6.0.8 (upgraded yesterday) RAM: 18GB Swap: 18GB MySQL: 5.1.72-2 (official Debain release) At this moment, update or change OS or MySQL version is not possible, there is any option that can help and i missed? Sorry by my english, and thank you in advance! Edit: I'm only using MyISAM tables, and cannot change to InnoDB.

    Read the article

  • Varnish returning 503, FetchError (could not get storage)

    - by Archan
    On the current setup we're running into a problem with Varnish, we're running a CentOS 5.7 x86_64 xenpv, with Cpanel WHM, hosted at VPS.net. Sometimes we will recieve a Guru Meditation from Varnish, and when we look in the varnishlog with the following command varnishlog -d -c -m TxStatus:503 it returns output similar to the following: 15 VCL_call c recv 15 VCL_acl c NO_MATCH devs 15 VCL_return c pass 15 VCL_call c hash 15 Hash c **** 15 Hash c ************* 15 VCL_return c hash 15 VCL_call c pass pass 15 Backend c 12 default default 15 TTL c 1835862523 RFC 0 -1 -1 1332454056 0 1332454055 375007920 0 15 VCL_call c fetch hit_for_pass 15 ObjProtocol c HTTP/1.1 15 ObjResponse c OK 15 ObjHeader c Date: Thu, 22 Mar 2012 22:07:35 GMT 15 ObjHeader c Server: Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 mod_fcgid/2.3.6 15 ObjHeader c X-Powered-By: PHP/5.3.9 15 ObjHeader c Expires: Thu, 19 Nov 1981 08:52:00 GMT 15 ObjHeader c Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 15 ObjHeader c Pragma: no-cache 15 ObjHeader c Content-Type: text/html; charset=utf-8 15 ObjHeader c X-Cacheable: NO:Cache-Control=private 15 FetchError c chunked read_error: 12 (Could not get storage) 15 VCL_call c error deliver 15 VCL_call c deliver deliver As far as I have could gather, we could try increasing the nuke_limit, but currently we have a nuke_limit of 500, and when running varnishstat -1 -f n_lru_nuked we "only" get a total of 1031, even though we have seen the error happen on several pages. When we then run top to see how much memory Varnish is using, it only shows that it is using 763m, although we've set it to be allowed to use 1200m. Any ideas of what the problem can be?

    Read the article

  • Wireless does not work on Ubuntu 9.04

    - by Yongwei Xing
    Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

    Read the article

  • FreeBSD's ng_nat stopping pass the packets periodically

    - by Korjavin Ivan
    I have FreeBSD router: #uname 9.1-STABLE FreeBSD 9.1-STABLE #0: Fri Jan 18 16:20:47 YEKT 2013 It's a powerful computer with a lot of memory #top -S last pid: 45076; load averages: 1.54, 1.46, 1.29 up 0+21:13:28 19:23:46 84 processes: 2 running, 81 sleeping, 1 waiting CPU: 3.1% user, 0.0% nice, 32.1% system, 5.3% interrupt, 59.5% idle Mem: 390M Active, 1441M Inact, 785M Wired, 799M Buf, 5008M Free Swap: 8192M Total, 8192M Free PID USERNAME THR PRI NICE SIZE RES STATE C TIME WCPU COMMAND 11 root 4 155 ki31 0K 64K RUN 3 71.4H 254.83% idle 13 root 4 -16 - 0K 64K sleep 0 101:52 103.03% ng_queue 0 root 14 -92 0 0K 224K - 2 229:44 16.55% kernel 12 root 17 -84 - 0K 272K WAIT 0 213:32 15.67% intr 40228 root 1 22 0 51060K 25084K select 0 20:27 1.66% snmpd 15052 root 1 52 0 104M 22204K select 2 4:36 0.98% mpd5 19 root 1 16 - 0K 16K syncer 1 0:48 0.20% syncer Its tasks are: NAT via ng_nat and PPPoE server via mpd5. Traffic through - about 300Mbit/s, about 40kpps at peak. Pppoe sessions created - 350 max. ng_nat is configured by by the script: /usr/sbin/ngctl -f- <<-EOF mkpeer ipfw: nat %s out name ipfw:%s %s connect ipfw: %s: %s in msg %s: setaliasaddr 1.1.%s There are 20 such ng_nat nodes, with about 150 clients. Sometimes, the traffic via nat stops. When this happens vmstat reports a lot of FAIL counts vmstat -z | grep -i netgraph ITEM SIZE LIMIT USED FREE REQ FAIL SLEEP NetGraph items: 72, 10266, 1, 376,39178965, 0, 0 NetGraph data items: 72, 10266, 9, 10257,2327948820,2131611,4033 I was tried increase net.graph.maxdata=10240 net.graph.maxalloc=10240 but this doesn't work. It's a new problem (1-2 week). The configuration had been working well for about 5 months and no configuration changes were made leading up to the problems starting. In the last few weeks we have slightly increased traffic (from 270 to 300 mbits) and little more pppoe sessions (300-350). Help me please, how to find and solve my problem?

    Read the article

  • How to make Synaptics touchpad work better on Linux?

    - by whitequark
    I have Debian Squeeze currently installed on a Samsung N250 netbook with a Synaptics touchpad. These touchpads are, generally, good, and everything works perfectly on Windows. The support is extremely sucky on Linux through. Of course it has all the cool features like two-finger scrolling, but the cursor (or whatever is a replacement for cursor when scrolling) is trembling awfully. It trembles when I just keep the finger on touchpad, it shakes awfully if the finger is close to the top of touchpad, and when I'm scrolling with it (no matter with two fingers or one), the page shakes a lot too. None of this behavior is observed even in Windows XP with just the default drivers installed. Here's the Xorg version: $ Xorg -version X.Org X Server 1.7.7 Release Date: 2010-05-04 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.32-5-686 i686 Debian Current Operating System: Linux mannaz 2.6.32-5-686 #1 SMP Fri Dec 10 16:12:40 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=/dev/mapper/mannaz-root ro quiet splash Build Date: 02 December 2010 01:08:37AM xorg-server 2:1.7.7-10 (Julien Cristau <[email protected]>) Current version of pixman: 0.16.4 and here is synclient -l output: http://pastebin.com/Eqa6hGXP

    Read the article

  • setting up git on cygwin - openssl

    - by Pete Field
    I'm trying to get git running in cygwin on a windows 7 machine I have git unpacked and the directory git-1.7.1.1 when i run make install from within that directory, I get CC fast-import.o In file included from builtin.h:4, from fast-import.c:147: git-compat-util.h:136:19: iconv.h: No such file or directory git-compat-util.h:140:25: openssl/ssl.h: No such file or directory git-compat-util.h:141:25: openssl/err.h: No such file or directory In file included from builtin.h:6, from fast-import.c:147: cache.h:9:21: openssl/sha.h: No such file or directory In file included from fast-import.c:156: csum-file.h:10: error: parse error before "SHA_CTX" csum-file.h:10: warning: no semicolon at end of struct or union csum-file.h:15: error: 'crc32' redeclared as different kind of symbol /usr/include/zlib.h:1285: error: previous declaration of 'crc32' was here csum-file.h:15: error: 'crc32' redeclared as different kind of symbol /usr/include/zlib.h:1285: error: previous declaration of 'crc32' was here csum-file.h:17: error: parse error before '}' token fast-import.c: In function `store_object': fast-import.c:995: error: `SHA_CTX' undeclared (first use in this function) fast-import.c:995: error: (Each undeclared identifier is reported only once fast-import.c:995: error: for each function it appears in.) fast-import.c:995: error: parse error before "c" fast-import.c:1000: warning: implicit declaration of function `SHA1_Init' fast-import.c:1000: error: `c' undeclared (first use in this function) fast-import.c:1001: warning: implicit declaration of function `SHA1_Update' fast-import.c:1003: warning: implicit declaration of function `SHA1_Final' fast-import.c: At top level: fast-import.c:1118: error: parse error before "SHA_CTX" fast-import.c: In function `truncate_pack': fast-import.c:1120: error: `to' undeclared (first use in this function) fast-import.c:1126: error: dereferencing pointer to incomplete type fast-import.c:1127: error: dereferencing pointer to incomplete type fast-import.c:1128: error: dereferencing pointer to incomplete type fast-import.c:1128: error: `ctx' undeclared (first use in this function) fast-import.c: In function `stream_blob': fast-import.c:1140: error: `SHA_CTX' undeclared (first use in this function) fast-import.c:1140: error: parse error before "c" fast-import.c:1154: error: `pack_file_ctx' undeclared (first use in this functio n) fast-import.c:1154: error: dereferencing pointer to incomplete type fast-import.c:1160: error: `c' undeclared (first use in this function) make: *** [fast-import.o] Error 1 I'm guessing that most of these errors are due to the iconv.h and openssl files which apparently are missing, but I can't figure out how I'm supposed to install those (if I am), or if there is some other way to get around this.

    Read the article

  • Apache httpd processes and PHP out of memory

    - by Ofri
    I have a VPS running apache-php-mysql on centos and a single drupal website installed. The VPS has 256MB of RAM (could be the root cause of all my problems... maybe I just need more). Whenever I try to open my website from multiple browser tabs (about 8... not 800) all at once, apache crashes! I have this on the log: [Wed Oct 24 11:26:31 2012] [error] [client xxx] PHP Fatal error: Out of memory (allocated 28049408) (tried to allocate 201335 bytes) in xxx on line 2139, referer: xxx I have read many many posts here, but I think there is something fundamental that I'm missing - If I understand correctly some php script tried to allocate 200K after allocating 28MB, and fails to do so. First question is: should this cause the apache to crash??? Next, I tried to look at 'top' command while I do my little test. Indeed I see 7 httpd processes, each reserving about 30MB - which explains why my RAM runs out. How do I prevent apache from creating new processes until it's out of memory? I tried configuring /etc/httpd/conf/httpd.conf like this: <IfModule prefork.c> StartServers 1 MinSpareServers 1 MaxSpareServers 1 ServerLimit 1 MaxClients 1 MaxRequestsPerChild 100 </IfModule> But got the same exact result! What am I missing? Thanks a lot!

    Read the article

  • GUI interfaces to ATI card behave weirdly out of the box and after updates.

    - by jdk
    My Lenovo W500 came with an ATI Mobility FireGL V5700 and both the Catalyst control center software and Vista display manager display four monitors. What's really annoying is the behaviour. My two active displays (laptop display + my external monitor) are always #s 3 and 4 respectively which doesn't make sense. This is out of the box. Additionally dragging & dropping is jumpy and displays #1 and 2 (always inactive because they don't exist to the software) are often preventing me from dragging #3 and 4 to the rightmost side. They also auto-snap to weird positions and certain sensible positions like position one directly over top of the other are not possible. The exact same annoyances are present when using the Windows Display manager too. In other words the interface is crap and I'm looking for a fix that's not wishing I had gone with nVidia instead. I've updated drivers, and Catalyst control centre. Have latest Windows and AMD/ATI updates. Any thoughts? Graphics Software Driver Packaging Version 8.563.2.1-090401a-079160C-Lenovo Provider ATI Technologies Inc. 2D Driver Version 7.01.01.849 2D Driver File Path /REGISTRY/MACHINE/SYSTEM/ControlSet001/Control/Class/{4D36E968-E325-11CE-BFC1-08002BE10318}/0001 Direct3D Version 7.14.10.0630 OpenGL Version 6.14.10.8306 Catalyst® Control Center Version 2009.0401.1328.22301 Graphics Hardware Primary Adapter Graphics Card Manufacturer Powered by ATI Graphics Chipset ATI Mobility FireGL V5700 Device ID 9591 Vendor 1002 Subsystem ID 2126 Subsystem Vendor ID 17AA Graphics Bus Capability PCI Express 2.0 Maximum Bus Setting PCI Express 2.0 x16 BIOS Version 010.088.000.021 BIOS Part Number BK-ATI VER010.088.000.021.034663 BIOS Date 2009/09/30 Memory Size 512 MB Memory Type DDR3 Core Clock in MHz 600 MHz Memory Clock in MHz 700 MHz

    Read the article

  • Issues with VSFTPD / FTP on Linux Ubuntu server - Steps for Troubleshooting?

    - by jnolte
    I am dealing with an issue I am unclear on how to resolve and have been pulling my hair out for some time. I have been trying to configure an FTP user using the following (we use this same documentation on all servers) Install FTP Server apt-get install vsftpd Enable local_enable and write_enable to YES and anonymous user to NO in /etc/vsftpd.conf restart - service vsftpd restart - to allow changes to take place Add WordPress User for FTP access in WP Admin Create a fake shell for the user add "usr/sbin/nologin" to the bottom of the /etc/shells file Add a FTP user account useradd username -d /var/www/ -s /usr/sbin/nologin passwd username add these lines to the bottom of /etc/vsftpd.conf - userlist_file=/etc/vsftpd.userlist - userlist_enable=YES - userlist_deny=NO Add username to the list at top of /etc/vsftpd.userlist restart vsftpd "service vsftpd restart" make sure firewall is open for ftp "ufw allow ftp" allow modify the /var/www directory for username "chown -R /var/www I have also went through everything listed on this post and no luck. I am getting connection refused. Sorry for the poor text formatting above. I think you get the idea. This is something we do over and over and for some reason it is not cooperating here. Setup is Ubuntu 12.04LTS and VSFTPD v2.3.5 Thank you in advance.

    Read the article

  • How do I keep a bridge enabled on a bonded interface?

    - by jlawer
    I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

    Read the article

  • vmware esxi 5, cant create snapshots and consolidate fails, how to delete old or consolidate redo logs?

    - by Scott Szretter
    I have a VM that seems to be working ok, but when VMWare DR (or I) tries to create a snap shot, it fails, and when I view the summary page of the VM it has a warning at the top showing that the disks need to be consolidated. So I go to snapshot manager for the VM and choose consolidate (in snapshot manager, there are no snapshots actually listed by the way). If fails with this error: This virtual machine has 255 or more redo logs in a single branch of its snapshot tree. The maximum supported limit has been reached, creating new snapshots will not be allowed. To create new snapshots, please delete old snapshots or consolidate the redo logs. If I browse the data store (which has plenty of free space, 2 TB and this vm is under 40gb), in the vm folder, I do in fact see a bunch of files, numbered all the way to 0255: myvm-000255-ctk.vmdk myvm-000255-delta.vmdk myvm-000255.vmdk How can I clean all this up? Is there an SSH command line command or can I delete some of the files safely? Thanks!

    Read the article

  • How to determine the root cause of a system lockup on Ubuntu 8.04 LTS?

    - by jdt141
    I'm currently working a project that involves setting up a PC/104 stack and running Ubuntu 8.04 LTS. We need to use the PC/104 stack because its an embedded application - and we're required to use a DeviceNet peripheral card to communicate to other devices. (DeviceNet is just a protocol on top of CAN.) Anyway, the following hardware is on the stack: Kontron MOPSPM104 with a 1GHz Intel Celeron processor ConnectTech FlashDrive/104 4GB Industrial Temp (-40 to +85 C) Woodhead (Molex) PC104DVNIO DeviceNet card A run of the mill 104 power supply The Kontron Board offers two serial ports, one VGA out, and two USB ports. The DeviceNet card is an ISA card. Because of this (per the User's Guide for the Kontron Board), I have manually set the IRQs in the BIOS to be appropriately configured, and turned off ACPI in both the BIOS and passed the appropriate flag in GRUB. I've installed Ubuntu 8.04 desktop, 32 bit. The problem that I'm having is that, from time to time, the entire 104 stack locks up. This only seems to happen in two cases, both of which we're running GNOME. We have a custom application that uses the DeviceNet card, and the system will lock up, or (more frequently) when we're running Firefox and either surfing for some information or trying to test it - typically by streaming video from a IP-camera. The reason I ask this questions is I cannot determine the root cause of this lockup. The IRQs appear to correctly configured in the BIOS and as the Kernel sees them, and nothing is logged to dmesg. If you all could help me determine the root cause of this lockup, I would greatly appreciate it. Thanks.

    Read the article

  • Why does a document in Word 2007 stop recognizing the mouse after the document loses focus?

    - by alt234
    When I open a document in Word 2007, everything works fine, I can edit, highlight text, etc. However, the instant Word loses focus, when I focus back the document doesn't recognize anything the mouse does. The tabbed menu at the top seems to recognize the mouse but the document itself does not. I can scroll through via the scroll-wheel and I can type. However, typing just shows up where the mouse cursor last was before focus was taken away. I've tried clearing some word data registry keys. I've also found that some Word Add-ins can cause problems. LaserFiche is one I see mentioned a lot. As far as I can tell I have no add-ons though. Any ideas? It's crazy-annoying. UPDATE- - Word is the only program that has this problem - Typically I have Toad (Oracle DB management app), an XP virtual machine with various apps running on it, Skype, Google Talk, and maybe a handful of other programs at any given time open... Windows Media player, Outlook. - Yes, this happens even if nothing else is running. From a fresh restart as well. - I'm running Vista 64 with SP1 - According to Windows Update, I have the latest of everything. This has been happening for a couple of months now. Just never took the time to look into because I usually never have to use word.

    Read the article

  • Certificates required for WHQL-certified drivers

    - by Kasius
    The 64-bit Windows 7 image that we deploy to machines at our site does not contain all of the certificates included on a default Windows image. Automatic root certificate installation is also disabled per policy from higher in the organization. We have had a lot of trouble installing many WHQL-certified drivers from reputable companies (ex. HP, Lexmark, Dell, etc.), and I hypothesize that a required certificate is missing from one of the certificate stores on the machine. The error we typically get is: The driver cannot be installed because it is either not digitally signed or not signed in the appropriate manner. I know that it is signed. A .CAT file is included, and it has the following tree from top to bottom: Microsoft Root Authority (thumbprint a4 34 89 15 9a 52 0f 0d 93 d0 32 cc af 37 e7 fe 20 a8 b4 19) Microsoft Windows Hardware Compatibility PCA (thumbprint 93 b8 d8 82 0a 32 db 20 a5 ea b6 8d 86 ad 67 8e fa 14 ea 41) Microsoft Windows Hardware Compatibility Publisher (thumprint b0 50 45 45 42 4e be 2c 16 2f 62 5b bf 5a e6 9b 96 bf 0b 0b) What certificates are required to install WHQL-certified drivers? Is it possibly something other than certificates? Thanks! NOTE: I have posted this question on Technet as well, but honestly, I've never had a lot of luck posting questions on the Technet forums.

    Read the article

< Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >