Search Results

Search found 14034 results on 562 pages for 'interface inheritance'.

Page 49/562 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• Multiple interfaces to one IP address?

  - by Delan Azabani

  At present, I have: a Netgear router with DHCP off at 192.168.0.1 my computer eth0 at 192.168.0.2 wlan0 at 192.168.0.2 The wlan0 interface always connects to the router, while the eth0 interface connects to other computers with crossover and acts as a dnsmasq DHCP server for network boot and installation. If I use the Gnome NetworkManager to enable both connections, that is, with wlan0 connected to the router/internet and eth0 to another computer, both as 192.168.0.2, I cannot access the internet while eth0 is connected. Why is this? How can I configure my computer to follow wlan0 for Internet usage, but use eth0 for itself (the latter is working but blocking wlan0).

  Read the article

• Disabling at application level a nic (network interface) on Windows

  - by Leandro

  How can I disable at application level a network interface? The main question is this: If I disable the nic trough wmic (win7) or devcon (XP), the "plug and play" of a wired nic doesn't work any more. For example, if the user put the cable on a disabled nic, the OS doesn't know about it. So I need to persist the enable condition but disabling the networking like a disable nic. There's some API, network configuration (routing, changing ip, changing gateway, any), .NET Framework resource (Only NetFramework 2.0) or do you can think in any workaround to do this? Suggest and ideas also will be treated as a solution. Thanks and kind regards.

  Read the article

• FreeBSD high load loopback interface

  - by user1740915

  I have a problem with a FreeBSD server. There is a FreeBSD 9.0 amd64, two network cards em1 (internet), em0 (local network) configured firewall ipfw, natd, squid (not transparent), the server acts as a gateway for access to the Internet. Next problem: upload via squid is very low. At this moment I see next: natd, dhcpd load the cpu at that time when uploading through squid and there are a lot of traffic through the loopback interface. ipfw show output 0100 655389684 36707144666 allow ip from any to any via lo0 00200 0 0 deny ip from any to 127.0.0.0/8 00300 0 0 deny ip from 127.0.0.0/8 to any 00400 0 0 deny ip from any to ::1 00500 0 0 deny ip from ::1 to any 00600 4 292 allow ipv6-icmp from :: to ff02::/16 00700 0 0 allow ipv6-icmp from fe80::/10 to fe80::/10 00800 1 76 allow ipv6-icmp from fe80::/10 to ff02::/16 00900 0 0 allow ipv6-icmp from any to any ip6 icmp6types 1 01000 0 0 allow ipv6-icmp from any to any ip6 icmp6types 2,135,136 01100 1615 76160 deny ip from 192.168.1.1 to any in via em1 01200 0 0 deny ip from 199.69.99.11 to any in via em0 01300 46652 3705426 deny ip from any to 172.16.0.0/12 via em1 01400 3936404 345618870 deny ip from any to 192.168.0.0/16 via em1 01500 4 336 deny ip from any to 0.0.0.0/8 via em1 01600 4129 387621 deny ip from any to 169.254.0.0/16 via em1 01700 0 0 deny ip from any to 192.0.2.0/24 via em1 01800 917566 33777571 deny ip from any to 224.0.0.0/4 via em1 01900 147872 22029252 deny ip from any to 240.0.0.0/4 via em1 02000 1132194739 1190981955947 divert 8668 ip4 from any to any via em1 02100 3 248 deny ip from 172.16.0.0/12 to any via em1 02200 35925 2281289 deny ip from 192.168.0.0/16 to any via em1 02300 1808 122494 deny ip from 0.0.0.0/8 to any via em1 02400 3 174 deny ip from 169.254.0.0/16 to any via em1 02500 0 0 deny ip from 192.0.2.0/24 to any via em1 02600 0 0 deny ip from 224.0.0.0/4 to any via em1 02700 0 0 deny ip from 240.0.0.0/4 to any via em1 02800 960156249 1095316736582 allow tcp from any to any established 02900 64236062 8243196577 allow ip from any to any frag 03000 34 1756 allow tcp from any to me dst-port 25 setup 03100 193 11580 allow tcp from any to me dst-port 53 setup 03200 63 4222 allow udp from any to me dst-port 53 03300 64 8350 allow udp from me 53 to any 03400 417 24140 allow tcp from any to me dst-port 80 setup 03500 211 10472 allow ip from any to me dst-port 3389 setup 05300 77 4488 allow ip from any to me dst-port 1723 setup 05400 3 156 allow ip from any to me dst-port 8443 setup 05500 9882 590596 allow tcp from any to me dst-port 22 setup 05600 1 60 allow ip from any to me dst-port 2000 setup 05700 0 0 allow ip from any to me dst-port 2201 setup 07400 4241779 216690096 deny log logamount 1000 ip4 from any to any in via em1 setup proto tcp 07500 21135656 1048824936 allow tcp from any to any setup 07600 474447 35298081 allow udp from me to any dst-port 53 keep-state 07700 532 40612 allow udp from me to any dst-port 123 keep-state 65535 1990638432 1122305322718 allow ip from any to any systat -ifstat when uploading via squid Load Average ||| Interface Traffic Peak Total tun0 in 79.507 KB/s 232.479 KB/s 42.314 GB out 2.022 MB/s 2.424 MB/s 59.662 GB lo0 in 4.450 MB/s 4.450 MB/s 43.723 GB out 4.450 MB/s 4.450 MB/s 43.723 GB em1 in 2.629 MB/s 2.982 MB/s 464.533 GB out 2.493 MB/s 2.875 MB/s 484.673 GB em0 in 240.458 KB/s 296.941 KB/s 442.368 GB out 512.508 KB/s 850.857 KB/s 416.122 GB top output PID USERNAME THR PRI NICE SIZE RES STATE C TIME WCPU COMMAND 66885 root 1 92 0 26672K 2784K CPU3 3 528:43 65.48% natd 9160 dhcpd 1 45 0 31032K 9280K CPU1 1 7:40 32.96% dhcpd 66455 root 1 20 0 18344K 2856K select 1 119:27 1.37% openvpn 16043 squid 1 20 0 44404K 17884K kqread 2 0:22 0.29% squid squid.conf cat /usr/local/etc/squid/squid.conf # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed acl localnet src 10.0.0.0/8 # RFC1918 possible internal network acl localnet src 172.16.0.0/12 # RFC1918 possible internal network acl localnet src 192.168.0.0/16 # RFC1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT # # Recommended minimum Access Permission configuration: # # Only allow cachemgr access from localhost http_access allow manager localhost http_access deny manager # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # We strongly recommend the following be uncommented to protect innocent # web applications running on the proxy server who think the only # one who can access services on "localhost" is a local user http_access deny to_localhost # # INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS # # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed http_access allow localnet http_access allow localhost # And finally deny all other access to this proxy http_access deny all # Squid normally listens to port 3128 http_port 192.168.1.1:3128 # Uncomment and adjust the following to add a disk cache directory. #cache_dir ufs /var/squid/cache 100 16 256 # Leave coredumps in the first cache dir coredump_dir /var/squid/cache I understand that the traffic passes through the SQUID several times. But can not find why.

  Read the article

• b43 module loaded, but no interface showed up

  - by Eduardo Bezerra

  I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

  Read the article

• exchange server 2010 Outlook Web Access - Exchange Control Panel WEB Interface

  - by Aceth

  from what i can gather the mailbox bit of the web interface works fine.. when any of the users go to options (top right) and try to use some of the features such as the Organise Mail Delivery Reports to find messages etc... it comes up with a message .. "An item with the same key has already been added" I've looked in the event viewer and i think its this error - Watson report about to be sent for process id: 7016, with parameters: E12IIS, c-RTL-AMD64, 14.00.0639.021, ECP, ECP.Powershell, https://x.x.x.x/ecp/PersonalSettings/Accounts.svc/GetList, UnexpectedCondition:ArgumentException, c09, 14.00.0639.021. ErrorReportingEnabled: False and Request for URL 'https://x.x.x.x/ecp/PersonalSettings/Accounts.svc/GetList' failed with the following error: System.ArgumentException: An item with the same key has already been added. at System.ServiceModel.AsyncResult.End[TAsyncResult](IAsyncResult result) at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.End(IAsyncResult result) at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.ExecuteSynchronous(HttpApplication context, Boolean flowContext) at Microsoft.Exchange.Management.ControlPanel.WebServiceHandler.ProcessRequest(HttpContext context) at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) I've tried googling but no luck that's relevant :(

  Read the article

• Getting network interface device name in powershell

  - by Grant

  I needed a powershell 2 script to get the name and device name of each interface like it is shown in network connections in control panel. Should be easy... $interfaces = Get-WmiObject Win32_NetworkAdapter $interfaces | foreach { $friendlyname = $_ | Select-Object -ExpandProperty NetConnectionID $name = $_ | Select-Object -ExpandProperty Name } However, $name comes back as "Broadcom BCM5709C NetXtreme II GigE (NDIS VBD Client)", whereas in control panel it shows "Broadcom BCM5709C NetXtreme II GigE (NDIS VBD Client) #69", because there are multiple cards. I can't find that number anywhere in the properties. How can I get both the Name and Device Name, exactly as shown in Network Connections, in powershell 2 on windows server 2008 r2?

  Read the article

• ip routes to specific interface

  - by user65053

  I am trying to figure out how to get all traffic to 10.8.78.* to connect using interface ppp0 when available how would I properly handle this (centos) and can I fall back on eth0 when pp0 is not up? /sbin/route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 69.19.219.69 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Utilize two gateways on the same network same interface with load balancing

  - by RushPL

  My setup is two ISPs on a single interface and single network. I can either set my default gateway to 192.168.0.1 or 192.168.1.250 and either work. My desire is to utilize both of them with some load balancing. I have tried to follow the advice given in here http://serverfault.com/a/96586 #!/bin/sh ip route show table main | grep -Ev '^default' \ | while read ROUTE ; do ip route add table ISP1 $ROUTE done ip route add default via 192.168.1.250 table ISP1 ip route add default via 192.168.0.1 table ISP2 iptables -t mangle -A PREROUTING -j CONNMARK --restore-mark iptables -t mangle -A PREROUTING -m mark ! --mark 0 -j ACCEPT iptables -t mangle -A PREROUTING -j MARK --set-mark 10 iptables -t mangle -A PREROUTING -m statistic --mode random --probability 0.5 -j MARK --set-mark 20 iptables -t mangle -A PREROUTING -j CONNMARK --save-mark Now then I do "traceroute somehost" repeatedly I can only get route through my default route which is 192.168.1.250. Shouldn't the packets change routes in a random manner? How to debug it?

  Read the article

• How to forward connection from one interface to another under linux

  - by Daniel

  Hi, I have linux box which has two network interface, eth0, eth1. from eth1 I can access an internal website, say under port 8080. from outside the box, I can't access that network. my question is, is there a way I set up something so from outside the box, there appears to be a web server running in port 8080 and when I connect to it, it automatically forwards to eht1 the internal site? I tried to enable ip forward and add a static route, but it doesn't work. thanks.

  Read the article

• Keepalived with apache unable to bind interface on Backup server

  - by davideagle

  I have two debian 6 servers running keepalived 1.1.20 with one server acting as a Master and the other as a Backup. Both servers host apache 2.4 that have a global Listener on all interfaces on port 80 (Listen *:80) how ever I have some sites that require a listener for port 443 (SSL) and that is configured for each VirtualHost in the Apache config since I do not want every VirtualHost to listen on port 443. The problem is when I try to start Apache on the Backup machine that does not hold the virtual interface the VirtualHost is supposed to be listening on, I get AH00072: make_sock: could not bind to address 1.1.1.1:443. I know this is expected behavior of Apache. The real question is are there any known workarounds or solutions to this scenario?

  Read the article

• Vmware server: Browser does not load user interface

  - by matnagel

  I have the latest vmware server isntalled on ubuntu 8.04 lts 64 bit. I access the user interface over this url, which matches my ip and port settings: https://10.1.1.99:11222/ui Sometimes it works in fierofox 3.6, but sometimes not. Same in Google Chrome. When it does not work, what happens is that the cert is checked, the browser is loading something, but the result is a white page. Sometimes the favicon of vmware (blue with 3 squares) appears, but only the white page. And sometimes it works. I reload many times, most of the time the whit epage appears again. On some days I succeed. But on many days not. I can give more info if someone tells me what is needed. Please help, we need this badly.

  Read the article

• Cisco ASA 5505 inside interface multiple ip addresses

  - by Oneiroi

  I have an issue this morning where I want to be able to assign multiple ip addresses to the inside interface to facilitate an ip range migration for an office. Namely from a 192.168.1.x range to the new range, with the minimum of interruption for those working in the office. (New DHCP leases will use the new range, whilst those still on the 192.168.1.x range can continue to work until their lease is renewed). However I can not for the life of me figure out how to achieve this, trying to create multiple interfaces for the job leads to complaints about the license only allowing 2 active interfaces. Any suggestions? thanks in advance.

  Read the article

• can not access dlink 604 set up interface

  - by user36089

  Hello everyone I used dlink-di604 enthernet board as router to share web access. My ISP provides the service base on Ethernet rathern than base on Ethernet pppoe mode. It is manually setup ipv4, subnet mask , DNS, Gateway etc Log in using web user name&password. I use http://192.168.0.2 try to access dlink di604 setup inferface, but failed I call command ipconfig /all Dos shell displayed: Ethernet adapter Local Connection: Physical Address: 00-3c-56-79-19-49 IPv4 address:10.7.8.225 subnet mask: 255.255.255.0 default gate way: 10.7.8.1 DNS servers 10.10.10.10 What is the correct way to access dlink 604 setup interface and set to share web access? Welcome any comment Thanks interdev

  Read the article

• How do you delete an iFolder from iFolder admin interface

  - by cheshirekow

  There are only two buttons at the bottom of the screen "enable" and "disable". When I check the box next to an iFolder one of them is lit (depending on what the state of the folder is)... but there is no button to delete the folder (as it seems there should be from the documentation). There is a delete button in the "orphaned" tab but how do you "orphan" an iFolder? I'm logged in to the admin interface as admin, who is currently the owner of the folder I wish to delete.

  Read the article

• Explorer.exe - No such interface supported and other issues

  - by tom

  The problem started when I uninstalled my ATI graphics driver and i used a driver cleaner. After i restarted win7 and it got to POST the screen just went completely blank. So i Used system restore from the repair menu to get back on. I found out that if I ran chkdsk the display just goes black after restart on startup and i have to use system restore to get back on windows7 not sure why this is. When i right click desktop and choose 'Screen Resolution' it says No such interface supported. Also when I click items such as device manager in the windows explorer it does not do anything. I have tried re-registering the DLLS but that did not do anything.

  Read the article

• NETSH : Set default ip address for an interface with multiple Ips

  - by elarichi.y

  To test a load balancer I need to switch my ip address several time a day, and keep other ips routing trough other Wans. I run these commands in a batch script: netsh interface ip set address "Connexion au réseau local" static %ipd% 255.255.255.0 192.168.1.1 1 netsh in ip add address "Connexion au réseau local" %ips1% 255.255.255.0 netsh in ip add address "Connexion au réseau local" %ips2% 255.255.255.0 ipd: is the default ip I want to set (all traffic should go trough it). ips1 and ips2 : are the secondary ips I want to keep but what ever I do all traffic goes trough one IP !! (first one in the range) Please help me with this issue.

  Read the article

• Which interface defines the physical address of a Dialup connection

  - by Debabratta

  I use dial up connection to connect to the Internet. When I type ipconfig/all in the command prompt it shows me a physical address along with description for the dial up connection. The description field shows WAN(PPP/SLIP)Interface. I want to know upon which this physical address depends? It depends on my computer or ISP. On changing my ISP, physical address for this dialup connection will change or remain same? Please give some idea.

  Read the article

• Cannot access Nagios Web Interface

  - by Dominiqs

  After successfully installing Nagios core 3.4.1 (i also installed plug-in1.4.11) on our linux rhel 5.3 server i cannot login to the nagios web interface.I am running apache 2.2.3 I am using internet explorer 8 and also firefox 3.6.3 When i try to enter the url http//localhost/nagios/ on a desktop (on the same network as the Nagios server)it does seem to like it but if i try http//x.x.x.x/nagios/ (where x.x.x.x is the IP address of my nagios server) it likes it but then the authentication popup appears after entering the password and username(nagiosadmin) it throws the errors below The server x.x.x.x at Nagios access requires a username and password Warning this server is requesting that your username and password be sent in an insecure manner(basic authentication without a secure connection) After a few attempts i get error 401 authentication required error from internet explorer ;this server could not verify that you are authorized to access the document requested. Either you supplied the wrong credentials or your browser doesnt understand how to supply the credentials required. Help Please anyone..seems like an authentication issue

  Read the article

• Inheritance security rules violated while overriding member - SecurityRuleSet.Level2

  - by Page Brooks

  I have a class that inherits from Exception. In .NET 4, I started receiving a runtime error: Inheritance security rules violated while overriding member: MyBusinessException.GetObjectData(System.Runtime.Serialization.SerializationInfo, System.Runtime.Serialization.StreamingContext)'. Security accessibility of the overriding method must match the security accessibility of the method being overriden. I think the issue is caused by the fact that I am overriding GetObjectData. I know one answer for resolving the issue is to set the SecurityRuleSet: [assembly: SecurityRules(SecurityRuleSet.Level1)] This is not an acceptable answer, I'd like to know how to fix the issue without having to relax the default security rules in .NET 4.

  Read the article

• Refactoring multiple interfaces to a common interface using MVVM, MEF and Silverlight4

  - by Brian

  I am just learning MVVM with MEF and already see the benefits but I am a little confused about some implementation details. The app I am building has several Models that do the same with with different entities (WCF RIA Services exposing a Entity framework object) and I would like to avoid implementing a similar interface/model for each view I need and the following is what I have come up with though it currently doesn't work. The common interface has a new completed event for each model that implements the base model, this was the easiest way I could implement a common class as the compiler did not like casting from a child to the base type. The code as it currently sits compiles and runs but the is a null IModel being passed into the [ImportingConstructor] for the FaqViewModel class. I have a common interface (simplified for posting) defined as follows, this should look familiar to those who have seen Shawn Wildermuth's RIAXboxGames sample. public interface IModel { void GetItemsAsync(); event EventHandler<EntityResultsArgs<faq>> GetFaqsComplete; } A base method that implements the interface public class ModelBase : IModel { public virtual void GetItemsAsync() { } public virtual event EventHandler<EntityResultsArgs<faq>> GetFaqsComplete; protected void PerformQuery<T>(EntityQuery<T> qry, EventHandler<EntityResultsArgs<T>> evt) where T : Entity { Context.Load(qry, r => { if (evt == null) return; try { if (r.HasError) { evt(this, new EntityResultsArgs<T>(r.Error)); } else if (r.Entities.Count() > 0) { evt(this, new EntityResultsArgs<T>(r.Entities)); } } catch (Exception ex) { evt(this, new EntityResultsArgs<T>(ex)); } }, null); } private DomainContext _domainContext; protected DomainContext Context { get { if (_domainContext == null) { _domainContext = new DomainContext(); _domainContext.PropertyChanged += DomainContext_PropertyChanged; } return _domainContext; } } void DomainContext_PropertyChanged(object sender, System.ComponentModel.PropertyChangedEventArgs e) { switch (e.PropertyName) { case "IsLoading": AppMessages.IsBusyMessage.Send(_domainContext.IsLoading); break; case "IsSubmitting": AppMessages.IsBusyMessage.Send(_domainContext.IsSubmitting); break; } } } A model that implements the base model [Export(ViewModelTypes.FaqViewModel, typeof(IModel))] public class FaqModel : ModelBase { public override void GetItemsAsync() { PerformQuery(Context.GetFaqsQuery(), GetFaqsComplete); } public override event EventHandler<EntityResultsArgs<faq>> GetFaqsComplete; } A view model [PartCreationPolicy(CreationPolicy.NonShared)] [Export(ViewModelTypes.FaqViewModel)] public class FaqViewModel : MyViewModelBase { private readonly IModel _model; [ImportingConstructor] public FaqViewModel(IModel model) { _model = model; _model.GetFaqsComplete += Model_GetFaqsComplete; _model.GetItemsAsync(); // Load FAQS on creation } private IEnumerable<faq> _faqs; public IEnumerable<faq> Faqs { get { return _faqs; } private set { if (value == _faqs) return; _faqs = value; RaisePropertyChanged("Faqs"); } } private faq _currentFaq; public faq CurrentFaq { get { return _currentFaq; } set { if (value == _currentFaq) return; _currentFaq = value; RaisePropertyChanged("CurrentFaq"); } } public void GetFaqsAsync() { _model.GetItemsAsync(); } void Model_GetFaqsComplete(object sender, EntityResultsArgs<faq> e) { if (e.Error != null) { ErrorMessage = e.Error.Message; } else { Faqs = e.Results; } } } And then finally the Silverlight view itself public partial class FrequentlyAskedQuestions { public FrequentlyAskedQuestions() { InitializeComponent(); if (!ViewModelBase.IsInDesignModeStatic) { // Use MEF To load the View Model CompositionInitializer.SatisfyImports(this); } } [Import(ViewModelTypes.FaqViewModel)] public object ViewModel { set { DataContext = value; } } }

  Read the article

• Entity Framework Model with inheritance and RIA Services

  - by TimothyP

  Hi, We have an entity framework model with has some inheritance in it. The following example is not the actuall model, but just to make my point... Let's say Base class: Person Child classes: Employee, Customer The database has been generated, the DomainService has been created and we can get to the data: lstCustomers.ItemsSource = context.Persons; EntityQuery<Person> query = context.GetPeopleQuery().Take(4); context.Load(query); But how can I modify the query to only return Customers ?

  Read the article

• CSS-Specifity and CSS Inheritance (concrete question)?

  - by jens

  Hello, i would by thankful for an official link (and section) of the specification for CSS, that explains if: .one two h1 {color:green;font-family:arial;} /*case 1 */ .one two h1 {color:blue;} /*case 2*/ will result in (when evaluated by the browser) .one two h1 {color:blue;font-family:arial;} /*case 3*/ or will it be: .one two h1 {color:blue;} /*case 4*/ ==I have read a lot about inheritance, specifity, cascading etc but I still have not found for the given example which rules apply here. In regard to specifity both elements are equal in specifity the case2 will be the most specify one (as it is equal specific but the last one). But does specifity always apply to the whole selector with ALL properties defined. Or only the the properties that are are in "competition" (and declared in both). thanks!!!!

  Read the article

• JSP template inheritance

  - by Ryan

  Coming from a background in Django, I often use "template inheritance", where multiple templates inherit from a common base. Is there an easy way to do this in JSP? If not, is there an alternative to JSP that does this (besides Django on Jython that is :) base template <html> <body> {% block content %} {% endblock %} </body> <html> basic content {% extends "base template" %} {% block content %} <h1>{{ content.title }} <-- Fills in a variable</h1> {{ content.body }} <-- Fills in another variable {% endblock %} Will render as follows (assuming that conten.title is "Insert Title Here", and content.body is "Insert Body Here") <html> <body> <h1>Insert title Here <-- Fills in a variable</h1> Insert Body Here <-- Fills in another variable </body> <html>

  Read the article

• Table-per-type inheritance insert problem

  - by gzak

  I followed this article on making a table-per-type inheritance model for my entities, but I get the following error when I try to add an instance of a subclass to the database. Here is how I create the subtype: var cust = db.Users.CreateObject<Customer>(); // Customer inherits User db.Users.AddObject(cust); db.SaveChanges(); I get the following error when I make that last call: "A value shared across entities or associations is generated in more than one location. Check that mapping does not split an EntityKey to multiple store-generated columns." With the following inner exception: "An item with the same key has already been added." Any ideas on what I could be missing?

  Read the article

• insert into several inheritance tables with OUTPUT - sql servr 2005

  - by csetzkorn

  Hi, I have a bunch of items – for simplicity reasons – a flat table with unique names seeded via bulk insert: create table #items ( ItemName NVARCHAR(255) ) The database has this structure: create table Statements ( Id INT IDENTITY NOT NULL, Version INT not null, FurtherDetails varchar(max) null, ProposalDateTime DATETIME null, UpdateDateTime DATETIME null, ProposerFk INT null, UpdaterFk INT null, primary key (Id) ) create table Item ( StatementFk INT not null, ItemName NVARCHAR(255) null, primary key (StatementFk) ) Here Item is a child of Statement (inheritance). I would like to insert items in #items using a set based approach (avoiding triggers and loops). Can this be achieved with OUTPUT in my scenario. A ‘loop based’ approach is just too slow where I use something like this: insert into Statements (Version, FurtherDetails, ProposalDateTime, UpdateDateTime, ProposerFk, UpdaterFk) VALUES (1, null, getdate(), getdate(), @user_id, @user_id) etc. This is a start for the OUTPUT based approach – but I am not sure whether this would work in my case as ItemName is only inserted into Item: insert into Statements ( Version, FurtherDetails, ProposalDateTime, UpdateDateTime, ProposerFk, UpdaterFk ) output inserted.Id ... ??? Thanks. Best wishes, Christian

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >