Search Results

Search found 5714 results on 229 pages for 'power mosfet'.

Page 49/229 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• Acer LCD says "no signal"

  - by Ken

  I have an Acer 24" LCD (model "AL2423WDR") that's about 3 years old. It worked perfectly for most of its lifetime so far. Recently it started giving problems. When I turn it on, it either says "no signal" on the display, or the power light goes yellow (as if in power-saving mode). This happens with both DVI and VGA (both of which worked fine before), and stranger still, the 4 buttons on the front, for accessing the on-screen menus, don't do anything. I've also tried different computer hardware and software (PC/Mac, Linux/MacOS), but nothing has worked. I've tried power-cycling it (with both the power button and the power switch), and also unplugging it entirely. The nonworking buttons suggest to me an issue with the firmware. I found a place on Acer's website that says I can send it in to have it fixed, at my expense, but I'll avoid that if I can. Is there a way to fully reset it manually? Or is there something else I can try?

  Read the article

• Keyboard lights sometimes stay on after PC is powered off. Why?

  - by Vilx-

  Sometimes when I power off my PC some lights on the keyboard stay on. It's pretty random which ones, though I suspect it has something to do with what lights were on just before the shutdown (if I vigorously follow that they are all off while the PC is shutting down then they stay off). Not that this would change anything, but it is annoying. Why does this happen and how can I avoid it? Added: I know that I can turn off the power completely to my computer and it will go off. That's not the point. Actually, I even want my keyboard to have power, because I use it to turn on my computer (the power button on the case is difficult to reach). I just want the lights to go off. Or at least understand why this happens. Oh, and it's a PS2 keyboard.

  Read the article

• dual boot preinstalled windows 8 laptop with windows 7

  - by sarathi

  I am having a hard disk in gpt partition style and Windows 8 is pre-installed in uefi mode. While trying to dual boot using usb bootable disk(using rufus,gpt partition style,fat32),it displays "Windows is loading files", then while displaying "Starting Windows" it hangs. So, I tried to install it inside Windows using setup.exe. Everything was running fine, but when it gets self restarted again, it got stuck at "Starting Windows". When restarted in Windows 8, it showed a htm file stating that "Windows cannot be installed on a computer using battery power. If the battery runs out of power during the installation, you might lose data. To continue the installation, plug in the computer's power adapter." I am sure that power adapter is connected. I Googled a lot on this, but I didn't get solution.

  Read the article

• Dell XPS 17 Laptop USB SS Ports don't work until machine rebooted

  - by Matt

  I have a new Dell XPS 17 laptop and have an issue that the two USB SS ports on the rear of the machine are not recognising anything when I start-up. Have tried mouse, keyboard, headset, USB display. If I plug a USB hub in the power light on the hub lights (presume this is hard-wired) but a mouse plugged into the hub does not light up. If I restart the pc the ports work fine. Also the other two USB ports work fine all the time. I have switched off the power saving setting on the device manager (Power managementAllow the computer to turn off this device to save power) and also in the advanced power settings (USB Settings USB Selective suspend setting:disabled) I have also disabled USB powershare in the BIOS (not sure what this actually does!) This is becoming very annoying having to restart the machine every day before I can start work Running Win 7 Pro x64 EDIT: I have found that setting USB Emulation to Disabled has helped the devices to be recognised during start up but they keep dropping out completely when in use EDIT 2: I contacted Dell about this issue who told me to update the BIOS driver, when I asked if I should downgrade from the factory installed A13 to the A12 posted on the dell website they said no. However there is now an A14 available on the website has anyone tried this?

  Read the article

• How to get Windows Server 2008 VM to use multiple cores

  - by David Fraser

  I have a Windows Server 2008 machine running in VirtualBox. On initial installation, only one processor was made available, but now I want to run it as a multiprocessor machine. I have made all four cores available in the VirtualBox settings (as well as enabling VT-x/AMD-V and Nested Paging), but Task Manager still only shows one CPU. However, the four CPU cores are visible in Device Manager under Processors. In the event log on startup, I can see the following relevant events: EventLog.6009 Microsoft (R) Windows (R) 6.00.6002 Service Pack 2 Multiprocessor Free Kernel-Processor-Power.4 Processor 0 exposes the following: 1 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) How can I make this system actually boot up as a multiprocessor machine?

  Read the article

• How to get Windows Server 2008 VM to use multiple cores

  - by David Fraser

  I have a Windows Server 2008 machine running in VirtualBox. On initial installation, only one processor was made available, but now I want to run it as a multiprocessor machine. I have made all four cores available in the VirtualBox settings (as well as enabling VT-x/AMD-V and Nested Paging), but Task Manager still only shows one CPU. However, the four CPU cores are visible in Device Manager under Processors. In the event log on startup, I can see the following relevant events: EventLog.6009 Microsoft (R) Windows (R) 6.00.6002 Service Pack 2 Multiprocessor Free Kernel-Processor-Power.4 Processor 0 exposes the following: 1 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) How can I make this system actually boot up as a multiprocessor machine?

  Read the article

• When machine is turned on, only the fan runs

  - by Gopal

  Hi, I have an issue slightly similar to this one posted here, http://superuser.com/questions/127016/troubleshooting-monitor-never-turns-on-system-fans-running-dvd-rom-does-not-op My configuration is as follows: EPOX 9NPA+ Ultra motherboard AMD Athlon 64 CPU Corsair 2 x 1GB PC3200 DDR RAM 1 DVD RW drive and 1 CD ROM Drive SATA 250 GB Hard drive 400W Power supply EVGA 256MB graphics card I have had this configuration for about four years. Last month, I started having issues in starting the machine. It wouldn't start when I press the ON button in the front of the case. So I used to pull out the power cord and plug it back in and then switch on in the front, and it used to work fine. And then one fine day, when I plugged in the power cord at the back, even without switching on the power-on button at the front, I saw that the fan at the back was running. So I opened the system. Then I could see that all the fans inside were running. I replaced the power supply. No luck there. Then I replaced the CMOS battery. Again nothing improved. Even when I removed all the cards and memory, I still get one short beep. That's it. Any idea how to proceed on this? Anything else could be checked? I want to confirm if this is a motherboard failure, before proceeding to replace it.

  Read the article

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  I recently did a full upgrade of Windows 7 on my Thinkpad. Everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen before the Windows logo appears. Disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this won't boot with battery plugged in is greatly appreciated. I need to take this battery out on the road/trains, etc. A little more detail on this story. The battery I had inserted when doing the (failed) boot was a long life battery. I have not tried inserting this battery when Windows is logged in. I have another (normal life) battery that I have charged up within Windows. It has just got to 100% and I am about to reboot with it in. I am using the Lenovo power manager to diagnose the battery - all seems OK. I will report back shortly as to the outcome. OK, so I chose the reboot option from within Windows, the machine seemed to shutdown okay, but then stalled. It didn't turn off completely and didn't reboot, but just sat, with the fan humming, somewhere in between! I had to hold the power button in for a few seconds until the fan stopped and then hit the power button again to boot the machine from fresh. One good thing, with this battery (the normal one) it booted into Windows 7 the first time with a battery! So, now I have rebooting issues. I have 3 errors in the event log: A timeout was reached (30000 milliseconds) while waiting for the lxdxCATSCustConnectService service to connect. The lxdxCATSCustConnectService service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. The following boot-start or system-start driver(s) failed to load: cdrom Any thoughts?

  Read the article

• Compaq motherboard CQ60 AMD - nvidia chipsed graphic problem

  - by Dritan

  Hi! It nice to have read that you solved this problem this way. I have 2 laptops Compaq CQ60 AMD Athlon with Nvidia graphic cards. the first one is new, when i press power button, it lights up only the ON led in front and nothing else, no fan working, blank screen, no beep.. I don't know what may be the problem. When I put on power adaptor, it lights up only the side power led near dhe power adapter plug but it doesn't light up the front led one. the second one have this problem that it spins the fan, light power and On led, but it doesn't show nothing on the screen blank (even with external monitor). In this case it maybe this problem of the Nvida Graphic Chip and it may need a reflow. I have an hot air station, but I don't know if I should try this or the oven one. Please can you give me any suggestion what to do to solve this. I have read that the solution of the Oven method is just temporary,maximum of three months, do you have the same experience about this? Any suggestion is wellcome.

  Read the article

• New build won't boot: some fans turning, no beep or video

  - by Dave

  When my new system is powered up, the case fan and power supply fans turn fine. The CPU fan twitches, but never gets going. Although I've heard that with AMDs and Gigabyte motherboards that is not necessary a problem. Hard drive is spinning. However, there is absolutely no indication that anything else is happening. The motherboard, as far as I can tell, does not have an internal speaker, but I harvested one from another machine and plugged it in and still no beeps at all. The monitor screen stays black, on both the integrated VGA and DVI. This is a brand new build, and has never successfully booted. My parts are: AMD Athlon II X2 245 Regor 2.9GHz Socket AM3 65W Dual-Core Processor Model ADX245OCGQBOX - includes CPU cooler) GIGABYTE GA-MA785GPMT-UD2H AM3 AMD 785G HDMI Micro ATX AMD Motherboard - Retail G.SKILL Ripjaws Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) Desktop Memory Model F3-10666CL8D-4GBRM - Retail CORSAIR CMPSU-400CX 400W ATX12V V2.2 80 PLUS Certified Compatible with Core i7 Power Supply - Retail SAMSUNG Spinpoint F3 HD502HJ 500GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive COOLER MASTER Elite 341 RC-341C-KKN1-GP Black Steel MicroATX Mid Tower Computer Case - Retail I also have a DVD burner, but it acts the same whether that is plugged in or not. I'm using the on board video. What I've tried so far: I've switched power supplies, with no difference. I've tried different monitors (of which all are working on other machines) with no difference. I have tried putting it one memory module at a time, with no difference. I have tried the absolute minimum I can think of (power supply into motherboard, power button ONLY plugged into front panel, CPU fan plugged in), with no difference. I appreciate any ideas anyone might have. Do I need to RMA the motherboard? This is my first build, so there might be something obvious. I was very careful in assembly with static; I'm confident nothing was zapped during assembly.

  Read the article

• Windows only successfully wakes up from sleep mode about 2/3rds of the time.

  - by Macha

  On my Vista laptop, when it goes into sleep mode (for low power, or manually being put into sleep mode, it happens regardless of how), about 1 in 3 times it won't wake up properly from sleep mode, and just display a black screen. The only option is to hold the power button to turn it off by holding the power button, and turning it back on again. (And yes, I have moved the mouse, pressed keyboard buttons and stuff).

  Read the article

• XCP vm created via xl create doesn't show up in Xencenter neither in xe vm-list

  - by user138664

  i am running XCP 1.4.90.530.170661 and i have many PV guests running and created via XenCenter. I have created now an openwrt PV guest via the xl create command but it doesn't show up in Xencenter neither in the vm-list command: xe vm-list uuid ( RO) : 6d29aac1-67ff-f83e-4dbc-894a3b6b9c10 name-label ( RW): slitaz power-state ( RO): running uuid ( RO) : 07d96dd1-8223-cd1c-587d-ae37e48d267b name-label ( RW): xen-centos6 power-state ( RO): running uuid ( RO) : 3164bcf1-e43c-badb-e0cf-5423751fffb9 name-label ( RW): xenwin7 power-state ( RO): running uuid ( RO) : 8a31725e-4bcb-48ac-ba7b-e7c1ba310789 name-label ( RW): Control domain on host: xen-mini power-state ( RO): running xl list Name ID Mem VCPUs State Time(s) Domain-0 0 300 2 r----- 4862.5 xenwin7 2 766 1 -b---- 4933.1 slitaz 10 255 1 -b---- 30.8 xen-centos6 11 767 1 -b---- 46.9 openwrt 12 32 1 -b---- 6.8 are these two different kinds of PV vm? if yes, is there a way to export the "xl create" one as xva/ova and import it to show up like the others? Thanks in advance, /c/

  Read the article

• How to get data from a borked Windows Home Server

  - by harhoo

  Yesterday we had a power surge, followed by a power outage. This left my WHS borked: powering on just gives to a flashing blue light (the led on the power supply also flashes green) - no fan or boot activity, nothing. I urgently needed some files off there in the short term (and the 500GB of photos, music, personal video etc in the long term) so I took the hard drive out and put it in my computer. The files and folders showed up, but I couldn't access them - clicking on an image gave an invalid image error in Picasa, I couldn't play MP3s etc. I changed the ownership and permissions of the files, still nothing. I booted in with a LiveCD, the same: files appear, but won't open. Is there anything else I can do? I'm now wondering if it was just the power cable that's broken, but if so, why can;t I access my files from the hard drive? If it is the power cable, and I replace that and the hard drive, will I have done any harm messing around with ownership and file permissions?

  Read the article

• Laptop automatic shutdown after 2 seconds

  - by leladax

  I'm trying to insvestigate which component produces this behavior. Other indications show it may be the GPU but I wonder if anyone knows more. It's a Toshiba Satellite X200 description: AC power shows the power being fed normally, when turned on the fan works and it appears to be starting up but after 2 seconds it shuts down with only the 'AC power connected" led on. -- seconds are about up to 4,maybe not 2 exactly.

  Read the article

• How do I make a form transparent while keeping the controls fully visible?

  - by Power-Mosfet

  I would like to have a form in which the controls on the form are fully visible but the form itself is invisible. If I change the form's Opacity, this makes both the form and the controls on it semi-transparent, so this doesn't work. I can't do this by setting the form's TransparencyKey, since I have a PictureBox on the form. If the image in the PictureBox happens to contain pixels that match the TransparencyKey, they appear as openings in the form, which I don't want.

  Read the article

• Toshiba A205-5804 freezes when plugged in

  - by heron

  Well I have a Toshiba A205-5804 and the problem is that the screen freezes anytime I plug the pc into the external power supply, not as most of the computers having the same issue, my computer DOES freeze in safe mode, and I really can't bear this problem for much longer... It's not an overheating problem, the computer is not getting hot or anything related, I've already tried changing the AC adapter, booting only with AC and no battery, and also all of these suggestions: Try changing the following setting in the bios setup, under the 'Advanced' tab Dynamic CPU Frequency: Mode = Always Low (NOT DYNAMIC) My laptop has been running on AC power without a problem for 24hours, including many restarts, and when I went back to the original bios setting, the problem returned almost straight away. EDIT Other suggestions I found on the web from here and here: Set the power plan to high performance Set the power plan to "Minimal Power Management" (1 and 2 do conflict) Start - Control Panel - Device Manager -- Processor - disable one of two processors - reboot normally 4.Do this: Only plug battery into laptop Turn on the laptop and start Windows normally Plug AC adapter into laptop, the screen will freeze Leave the laptop the way it is for 12-24 hours After 12-24 hours, turn it off the hard way Once it is turned off, turn it back on. The laptop is working now. I have no idea of what can it be...

  Read the article

• building a new pc - no display, no beeps

  - by Adam

  Hi Building a new pc using this motherboard: GA-MA785GMT-UD2H and a 500W power supply (1 x 20 pin & 1 x 4 pin connectors). The CPU fan, hard drive and power supply all spin up but no display on the monitor and no beeps. Have tried: taking out all of the memory and still no beeps used a different power supply and still no display I only have the Motherboard, memory, CPU, heat sink & fan & power supply connected. Any ideas? Do I have a faulty motherboard?

  Read the article

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

• Holding off Windows 2000/3 Server in Shutdown

  - by user1668993

  We have a C# VS2010 application running on a Windows 2000 Server box (there is also a Windows 2003 Server box) as pretty much the only application running. We remove power from the box. There is a short duration battery (maybe 3 minutes of power) which then waits 10 seconds and then decides things are coming down and notifies Windows that it needs to shut down. Windows sends a CTRL_SHUTDOWN_EVENT event to the application which fields it and tries to keep Windows from going down for a while to let another computer which communicates with this one time to do some file work on the first computer. It does this by a timing loop and after the loop is over, it exits gracefully and the computer shuts down. Nice plan but it doesn't work. The application gets to maybe 20 seconds and the application is forcibly killed by Windows and Windows shuts down. At 90 seconds, the hardware firmware running the battery turns off power to the computer. I have tried searching to find out how to hold off Windows for a bit of time. I tried creating (it wasn't there) the HKEY_LOCAL_MACHINE subtree: \SYSTEM\CurrentControlSet\Control\WaitToKillAppTimeout registry key to 60000 but though it seemed to keep the popup from happening, Windows itself died at about the same amount of time -- we think without having the opportunity to shut itself down gracefully. Maybe the registry key worked but wasn't enough. Basically I have an "ill-mannered" application which is refusing to shut down (for the best of reasons) and without the registry key thing, Windows eventually shuts it down anyway and then shuts itself down. With the registry change, we think what is happening is that Windows doesn't shut down the application but Windows itself is killed suddenly without shutting down but power is still not pulled for about another minute, and then power is pulled. So maybe we have layers here. First there is how long the application tries to stay open. Then there is how long Windows is prepared to allow it to stay open. Then there is ... something... which kills windows. Then there is the power loss. Anyone have any ideas how we can get windows to stay open and in operation say to 70 seconds instead of about 20? Is our registry key right, but not enough? Is there some additional key we need to set to determine how long after windows is notified of a shutdown before it just kills itself? Thanks in advance.

  Read the article

• Battery notification always showing 'xx% remaining' with Windows 7 on an acer Aspire 5590

  - by dindeman

  My battery level always shows up as something like 55% remaining or 63% remaining ...etc despite that it is in fact charging. Additionally it doesn't go any further than 80% remaining even if I keep it in charge forever. This leads me to a side annoying effect which is that I cannot proceed to install Windows 7 Service Pack 1 as its installer requires the laptop to be plugged with a power cord. My laptop is plugged with the power cord but because of the above issue (it doesn't display anything else than the xx% remaining) Windows thinks that the laptop is using its battery and that the power cord is disconnected. I have installed the original acer ePower Management tool that let you configure the power scheme... etc, I was hoping that this would help me circumvent the 80% issue but it doesn't.

  Read the article

• what happened about HP EliteBook 8530p Battery?

  - by austking

  I have a problem to my good old HP EliteBook 8530p Notebook, a few days before he went very well ", the notebook will not turn on completely over, or not turn on itself is left off for several hours ... ONLY restarts itself remove the power cord and then starts with the battery mass after numerous attempts, then it just starts again refer the power cord then everything works i.e usa direct power .... What can be I'm problem? to turn it on this morning it took me 20 min HELP ME!!! Thanks in advance

  Read the article

• Video adapter problem on new motherboard

  - by Dmitriy Matveev

  Something bad happened to my PC several days ago. I wasn't near my PC, so I have no idea about what happened it was just halted. When I tried to boot it was entering infinite loops of a few seconds power up (cpu, hdds, etc) and then power down. I've tried to boot the system with no additional components (that includes hdd, video, network adapters and even memory) connected and that didn't solved the problem, so I've made a decision that most likely it's either some a problem with power unit or with motherboard. I've tried to replace my power unit by another one (which was expected to be working) and the problem didn't resolved again. I've bought a new MB (ASUS P5KPL-AM SE) and tried to get it running with my old CPU and memory (I hope it's still alive). Since this MB include on-board video I've tried to run the PC without installation of mine video. The PC wasn't running and the BIOS was beeping one long signal following by two short (Does it means a video problem?). After that I've installed my video adapter to PCI-E slot and tried to boot the system again and the BIOS was beeping the same. I don't get it. I may expect some problem with CPU and/or memory since I don't know what happened to my PC (maybe some power failure or something different), but not with video and not with on-board video on newly bought MB. How can I understand what's wrong with my system now?

  Read the article

• How to avoid error messagebox if .net is not installed on client system.

  - by Power-Mosfet

  Hi, I have a C# application which request .net 2 on client system. I like to replace the error message box in case if .net2 is not detected with ruuning an executable program which I have a written how do not request .net2.

  Read the article

• get a different file name

  - by Power-Mosfet

  Hi, How do i get a different file name on a webserver by requesting the url. for example "file" click url link and get "file.bin" the "file" is located on a webserver by requesting the url, user can download "file.bin" instead of "file" something like (file + .bin)

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >