Search Results

Search found 2181 results on 88 pages for 'wifi cordon'.

Page 49/88 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• What Wireless Router/ADSL Modem to get? N-band a must!!

  - by JJarava

  I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

  Read the article

• Windows Explorer slow to open networked computer, fast to navigate once opened

  - by Scott Noyes

  I open Windows Explorer and enter an IP for a computer on my home network (\\192.168.1.101). It takes 30 seconds or more to present a list of the shared folders. It does not appear to be an initial handshaking/authentication thing; even if I allow the view to load and then immediately load the same again, it is always slow. Once they appear, navigating through folders and opening files is fast. Also, navigating directly to a folder (\\192.168.1.101\My Music) is fast, even if it's the first connection since a restart. Using \\computerName instead of the IP address gives exactly the same results. Pings return in 1ms. net view \\computerName (or \ipAddress) returns the list of shared folders fast. This makes me suspect an Explorer issue rather than a network issue. Suspecting that the remote computer was being automatically indexed or something, I went into Tools-Folder Options-View and unchecked "Automatically search for network folders and printers," but that made no difference. De-selecting the "Folders" icon near the address bar makes no difference. Adding the IP address and computer name to the hosts file makes no difference. Both computers involved are laptops running Windows XP. Both have WiFi and cable adapters. Mine is not connected via cable. The result is the same whether the target is plugged in to the cable or not (although the IP address changes - 192.168.1.101 over cable, 192.168.1.103 over WiFi.) We are using DHCP assigned by the router.

  Read the article

• Epson Artisan 800 on Ubuntu/Linux

  - by Tim Lytle

  Update for Ubuntu 10.04: Printing should work 'out-of-box', scanning still needs the newer sane backend. Looking for a known good way to setup an Epson Artisan 800 on Ubuntu specifically or any linux box in general. It is a printer/scanner with ethernet/wifi/usb. I'd like to use it as a network printer/scanner being able to do both from my Windows and Ubuntu machines; however, if it needs to be physically connected to a computer (preferably the Ubuntu machine) that is doable (again, then sharing print/scan functions to the network). Basically, I'm looking for someone who has used this printer/scanner (or similar) in a multi-platform environment to share how the set it up and how well it worked. Updated: A little more information, like most printers (I expect) the documentation for the printer basically says, "don't use plug-n-play, run our setup CD from your Windows/Mac system", to do anything (set it up for network use even). I guess that's to make it easy for anyone else to setup, but when you're looking to use it with an unsupported (by Epson's documentation) OS, you're just stuck on your own. What I was hoping for was someone who could say, "Forget the bundled software, do [this] to set it up on wifi manually, install [this] to connect to the scanner from [os], printing works with [this] driver - at least that's how I set it up." I'll will (and have so far) use the information here, and post my own setup when I'm done, if there's no one else out there with that experience.

  Read the article

• Prevent outgoing traffic unless OpenVPN connection is active using pf.conf on Mac OS X

  - by Nick

  I've been able to deny all connections to external networks unless my OpenVPN connection is active using pf.conf. However, I lose Wi-Fi connectivity if the connection is broken by closing and opening the laptop lid or toggling Wi-Fi off and on again. I'm on Mac OS 10.8.1. I connect to the Web via Wi-Fi (from varying locations, including Internet cafés). The OpenVPN connection is set up with Viscosity. I have the following packet filter rules set up in /etc/pf.conf # Deny all packets unless they pass through the OpenVPN connection wifi=en1 vpn=tun0 block all set skip on lo pass on $wifi proto udp to [OpenVPN server IP address] port 443 pass on $vpn I start the packet filter service with sudo pfctl -e and load the new rules with sudo pfctl -f /etc/pf.conf. I have also edited /System/Library/LaunchDaemons/com.apple.pfctl.plist and changed the line <string>-f</string> to read <string>-ef</string> so that the packet filter launches at system startup. This all seems to works great at first: applications can only connect to the web if the OpenVPN connection is active, so I'm never leaking data over an insecure connection. But, if I close and reopen my laptop lid or turn Wi-Fi off and on again, the Wi-Fi connection is lost, and I see an exclamation mark in the Wi-Fi icon in the status bar. Clicking the Wi-Fi icon shows an "Alert: No Internet connection" message: To regain the connection, I have to disconnect and reconnect Wi-Fi, sometimes five or six times, before the "Alert: No Internet connection" message disappears and I'm able to open the VPN connection again. Other times, the Wi-Fi alert disappears of its own accord, the exclamation mark clears, and I'm able to connect again. Either way, it can take five minutes or more to get a connection again, which can be frustrating. Why does Wi-Fi report "No internet connection" after losing connectivity, and how can I diagnose this issue and fix it?

  Read the article

• Need to have access to my office PC from my laptop hopping through two VPN servers

  - by Andriy Yurchuk

  Here's the illustration of what I have ( http://clip2net.com/s/2fvar ): My office PC with it's IP of 123.45.e.f. Office VPN, which I will connect to from my VPS to get to my office PC. My own VPS, which I use as a: client to connect to office VPN (through vpnc, which creates a tun0 with 123.45.c.d IP address); VPN server my laptop can connect to (OpenVPN, tun1, 10.8.0.1) My own laptop I will use as a VPN client to connect to VPS OpenVPN server (will create a tun0 with 10.8.0.2 IP address) Now what I have to do is to allow my laptop to connect to at least my office PC, but preferably to all the 123.45.x.x subnet. Please advice on how to best configure OpenVPN, routing, iptables or whatever else is needed on my VPS so that my laptop could gain access to my office PC. P.S. The reason I'm hopping through my VPS is that being connected to the office WiFi I cannot access my office PC and I cannot connect to office VPN (which is another way to access my office PC). The only way to access my PC from office WiFi I have is hopping though an outside network.

  Read the article

• Need help using a super scope

  - by Vdub

  I have a windows server 2008 r2 standard running our DCHP, DNS, and AD. also I have (3) HP Pro Curve 2510-G switches (J9280A). Right now our LAN is set up 192.168.50.2-192.168.50.254 on our sub-net (A) and another scope with 192.168.51.2-192.168.51.254 sub-net (B) both have sub-net mask of 255.255.255.0. The same server is our DNS which is 192.168.50.242 and our firewall (watchguard) is the gateway at 192.168.50.1. Right now the sub-net (B) does not have DHCP active so only sub-net (A) is giving a pool. My problem is that we are trying to have open WiFi on our network and i am assuming that i can use the sub-net (B) for that if i activate it and use sub-net (A) for our staff only. I have noticed that when i set up a static on a client pc and set it to 192.168.51.x i cannot use the DNS of 192.168.50.242 however i can use 8.8.8.8 and it works fine, i am guessing that because it is on a different sub-net? Forgive me as i am very new at this and dont know a lot. Is there easy way with the equipment i have to a accommodate wifi for hundreds of people without causing problems for our staff? (multiple same IP address assigns) I appreciate any and all info!

  Read the article

• Can Current Backflow from Powered Hub's Adapter & cause PC Damage?

  - by SuperUserMan

  Getting this short: Can current flow from a powered USB hub's power adapter (lying 10 Meter away) back to computer via usb port and cause damage to Computer components like mobo, etc? What should be my concerns? Using a 2 Amp 5V Power adapter to power a 10m Long Active Repeater USB extension cable with 4 port HUB & plugging into PC's Front port, causes PC Chassis fan to keep running (thought slower than regular speed) Front Chassis HDD & power LED to turn on (though bit dim) may be other things which i cant detect/see at chip level, in motherboard?? All this even after PC is shut down (bit scary) More detail (in case still want to read): To run 4 High power (needing 450 mAmps) Wifi Adapters, far away from PC, Bought Active Repeater USB Extension Cable with 4 Ports & power port at far end http://www.ebay.com/itm/33FT-USB-2-0-Male-to-Female-Extension-Cable-Hub-Splitter-Adapter-with-4-USB-Port-/390846115254 Then added a locally bought 2 Amp 240V AC to 5V DC Power Adapter and plugged into USB hub which is a part of & situated at far end of a 10 Meter Active Repeater usb extension cable. Even 4 Wifi Adapters run fine (appear to) using this setup, but running chassis fan, dimly lighted Power & HDD LED, even when PC is switched off is bit scary and surely mean 5V & some current is flowing all though that 10 meter extension cable into my USB port & powering stuff. Can this cause damage? and what should be my concerns. Of course I can't switch off the power adapter (lying 10 meters away from PC) every time I switch off my PC to prevent this.

  Read the article

• Android webbrowser returns code 500 for webpage on Nginx webserver

  - by Paxxil

  Hey! I've come to a very weird behavior of a web browser on android mobile phone (I've tried HTC Wildfire and HTC Desire phones). I have a web server with Nginx v0.8.54. When i try to open a web page on the phone it shows me error: The requested item could not be loaded! (Status code: 500) BUT it only happens when I am requesting page through Mobile network. On Wifi it works just fine .... but there is more .... if I stop Nginx and start Apache web server it works just fine on both Mobile network and wifi. I've also tried other mobile network and it is the same behavior. Some server stats: Firewall is OFF Selinux is OFF the web page (using Nginx web server) opens normally on any other browser (IE, FF, Opera, Chrome, Safari) on the laptop or PC Nothing in nginx error.log This is the only entry in access.log when the page is requested: xxx.xxx.xxx.xxx - - [17/Mar/2011:11:19:49 -0500] 200 "GET / HTTP/1.1" 27405 "-" "Mozilla/5.0 (Linux; U; Android 2.2; en-gb; Desire_A8181 Build/FRF91) AppleWebKit/533.1 (KHTML, like Gecko) Version/4.0 Mobile Safari/533.1" "-" index.html has only "Hello World" string in it. There is no fishy javascript or anything else. .... but there is even more.... if i open the same page on another server, with the same Nginx build, with the same server and web server configuration.... it opens just fine. if anyone has any idea on what may be going on, i would really appreciate it if you let me know. Thanks! EDIT: i forgot to mention that page opens OK on Iphone and Nokia

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

  - by Gordo

  I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

  Read the article

• Laptop Most Likely to Have Good Driver Support

  - by ShabbyDoo

  Through numerous bad experiences, I have learned that the most likely cause of laptop "failure" is the lack of updated drivers for new operating systems. As an example, I have a perfectly good Thinkpad T42 at home which runs Windows 7 just fine for my purposes except that no compatible ATI video drivers are available, and the generic drivers have flicker effects. I recently saw an ASUS laptop which looked quite nice except that I would be beholden to them to release ATI video driver updates customized for it. And, I can't trust them to do that for more than six months. What laptops (manufacturer/line) should I consider so that I could expect at least a couple years of frequent updates? I plan on running Windows 7 and installing whatever successor comes out. I like Intel components (especially WiFi) because I can install their drivers directly from them, and they have a long history of providing updates for years after shipping a particular component. More generally, components from companies which are likely to update drivers frequently are good as long as I can install the component manufacturer-provided drivers without laptop-specific customization (like the ATI drivers). Also, if a component can be replaced easily, I am less concerned. For example, Dell stopped pumping out updated drivers for one of its mini-PCI WiFi cards. The solution was to buy an Intel replacement on eBay for $12! That's fine. I can deal with that. So, what laptops should I consider so that I'm not likely to be stuck between a rock and a hard place?

  Read the article

• Fedora 15: em1 recently dissapeared and hostapd no longer serves internet to wirelessly connected devices

  - by Daniel K

  I have a laptop running hostapd, phpd, and mysql. This laptop uses an Ethernet connection to connect to the internet and acts as a wireless access point for my workplace's wifi devices. After installing some software and reconnecting my Ethernet elsewhere, my "em1" device is no longer present and wirelessly connected devices can no longer reach the internet. The software I recently installed is: pptp, pptpd, and updated some fedora libraries. I have also recently moved my desk and laptop to another location and thus had to reconnect the Ethernet elsewhere. Wifi devices no longer have access to the internet. Wirelessly connected devices are able to successfully log into the laptop, showing full strength, correct SSID, and uses the proper password. However, when I tried to connect to a site like google, the request times out. The device "em1" also no longer appears on my machine. Running: # ifup em1 will give me the following output: ERROR : [/etc/sysconfig/network-scripts/ifup-eth] Device em1 does not seem to be present, delaying initialization. And running: # dhclient em1 has the following output: Cannot find device "em1" When I run # dmesg|grep renamed, I get the following: renamed network interface eth0 to p4p1. I've tried to connect to the internet through p4p1 directly from the laptop and was successful. However, my wireless devices connected to my laptop are not able to connect to the internet. I have uninstalled pptp and pptpd using # yum erase ... but the problem still persists. To install pptp I used: # yum install pptp To install pptpd I did the following: # rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc15/pptp-release-current.noarch.rpm # yum install pptpd To update my fedora libraries I used: # yum check-update # yum update EDIT: Running # route produces the following results: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.11.200.1 0.0.0.0 UG 0 0 0 p4p1 10.11.200.0 * 255.255.252.0 U 0 0 0 p4p1 172.16.100.0 * 255.255.255.0 U 0 0 0 wlan0

  Read the article

• Windows 7 Automatically Connecting To Unsecured Wireless Networks On Startup

  - by Xtend

  Most of the questions on this topic related to folks connecting to somebody else's wireless network when their own was available and could remedy the situation by going to their connections and unchecking the "connect automatically" box. See this: " Avoid automatically connecting to wireless network on windows 7 " as an example. In my situation, I've noticed that Win 7 will automatically connect to any unsecured wifi network - even if I have never connected to it in the past. If I am traveling and boot Win 7, it will start and connect to what appears to be the best signaled unsecured network without prompting me for confirmation (note: in the above link, "Naveen" seems to have same problem). Obviously, that is a security concern to me. Further, when I open "Network and Sharing" and "Manage wireless networks" the network is not displayed (probably because I labelled it a public network). Again, these are new, never connected with before, wireless networks. I always promptly disconnect from them but don't want to have to be on constant guard for an auto connection to a malicious network. This began about a month ago, as I recall, Win 7 did not behave like this in the past, I didn't monkey with wifi settings, and don't use a 3rd party connection manager. I did have to download some internet security certificates for army website access but I don't think that should mess with network settings. Any ideas how I can tell Win7 cease automatically connecting to networks or, at least, to prompt me for a confirmation before connecting?

  Read the article

• HP dv6910 laptop no longer recognizes wireless adapter, dvd drive, and one usb port. What can I do about this?

  - by Joan H.

  In the last 3 weeks, my not even 3 year old HP laptop (vista) just seems to be failing. First, one of the usb ports stopped working. Next, the dvd drive all of a sudden was not recognized as even existing, so it is now useless. And as of today, I no longer seem to have a wireless adapter on my laptop. It doesn't show up in device manager, same as the dvd drive. I can connect to the internet by ethernet cable, but not wirelessly. It worked fine last night; now it doesn't even exist! I have tried a 'hard reset' I read about on HP's forum- no help. I am not sure what else to try. I read about the USB wifi dongle in another response, but I already have maxed our my usb ports even though I have bought a USB hub since the one port failed. Plus, I'd like my laptop to just work like it's supposed to instead of being jerry rigged with usb hubs, external dvd drives, and wifi dongles etc. Any ideas?

  Read the article

• Want to send my neighbors to a certain website via DNS, but don't have a clue how. [closed]

  - by Akku

  My neighbors have an unsecured WIFI router, and over the administration web-UI of the router I could log in as there was no password set. I don't know which of my neighbors these are, and I'd like to configure their router in a way that they come to my website instead of Google and Facebook, where I set up a warning in german. It this page: http://www.abelssoft.de/liebenachbarn/ Basically, I just want to see if and how this is possible - I'm aware that I could just set the WiFi-password and have them call their network provider to reset the thing, but I really want to see if this could work, because it would be a way cooler effect :-). So this router interface doesn't allow custom redirects, only filters. BUT I can set the DNS that is used, so I thought there might be the possibility to set up a custom DNS on a server, set it as the main DNS and redirect from Google to the URL above. Is this possible? If so, please try to detail a way that I have to go though to achive this. Note that I'm not the super-Linux-skilled person, I have a dyndns account and a Windows machine it points to as well as an Apache+Tomcat if that helps. I could also set up virtual machines on the windows server and redirect to those using a different port. Or is there maybe a webservice that provides such custom DNS?

  Read the article

• Slow upload, fast download on Windows 7 64bit system

  - by Malik

  I've got a weird problem in the download speeds on my desktop PC (Windows 7 Home Premium 64bit) are consistently fast (approx. 400kB/s) but uploads are very slow (around 6-10kB/s). This has been going on for the last 3 weeks or so. I am a very competent user and troubleshooter, and have searched online for 2 weeks for a solution, to no avail. Part of the problem is that internet is provided by WiFi by my landlord and I have no access to the router (BT Home Hub router) although I know for sure he wouldn't have the first idea on how to restrict my usage :) (rules that out) Anyway, I've tried: - various drivers (my Wifi 'card' is TP-link TL-WN851N, and I've tried TP-link + Atheros + Qualcomm Atheross drivers, suggested by Microsoft) - various tweaks to network parameters (e.g. as suggested by SpeedOptimser) - various tweaks to Windows 7 services (e.g. disabling/manual-ing unecessary services) - raising and lowering head onto a reasonably firm surface at moderate frequency (jk :D) None of the above have helped, and I'm officialy asking for help now!! Thanks for your time and effort in advance!

  Read the article

• Switch between network configurations via command line in fedora 17

  - by Mike Fairhurst

  I have two different setups I use on my work laptop; one enables synergy over an ethernet ssh tunnel with my work computer on the local network, and the other opens an HTTP tunnel to my work computer from outside the network. When I have wifi enabled at work, my laptop seems to use it by preference. This makes synergy run incredibly slowly. At home I must use wifi. I have scripts that begin my ssh tunnels, add my ssh keys, and starts up other programs like synergy, and close themselves when I shut my laptop. However, every day I have to start out my routine by opening my gnome-control-center and turning on my ethernet. I have tried route add and ifup, none of it works, so I dove into gnome-control-center's source code and found that it enabled the connection by libnm's method nm_client_activate_connection with some libnm specific structs that I am having trouble tracking down. I'm not much of a c programmer, and I'm not familiar with either GTK or libnm. Does anybody know what fedora 17 does with ethernet connections to fully enable them? Or does anybody know what libnm does to fully enable an ethernet connection? Do I have to write a c script to run libnm for me to fully emulate whatever gnome-control-center is trying to do?

  Read the article

• Getting dwl-g122 to work on ubuntu

  - by User1

  I have a USB WiFi adapter, D-Link dwl-g122. I'm running Ubuntu 10.4. My laptop has a built-in wireless card that is connecting fine to the router. I plug in the usb and it never really connects. Here are some details: iwconfig wlan1 IEEE 802.11bg ESSID:"\x0B\xE1..." Mode:Managed Frequency:2.457 GHz Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on lshw -c network: *-network:1 description: Wireless interface physical id: 3 logical name: wlan1 serial: 00:13:46:8b:xx:xx capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg dmesg [ 1096.814176] wlan1: direct probe to AP xxx (try 1) [ 1096.820960] wlan1: direct probe responded [ 1096.820969] wlan1: authenticate with AP xxx (try 1) [ 1096.823790] wlan1: authenticated [ 1096.823869] wlan1: associate with AP xxx (try 1) [ 1096.827667] wlan1: RX AssocResp from xxx (capab=0x411 status=0 aid=1) [ 1096.827674] wlan1: associated [ 1142.590912] wlan1: deauthenticating from xxx by local choice (reason=3) lsmod|rt2 rt2500usb 19643 0 rt2x00usb 11260 1 rt2500usb rt2x00lib 32133 2 rt2500usb,rt2x00usb mac80211 238896 3 ath5k,rt2x00usb,rt2x00lib cfg80211 148725 4 ath5k,ath,rt2x00lib,mac80211 led_class 3764 3 ath5k,rt2x00lib,sdhci It looks like the driver loads but it doesn't feel like connecting. The behavior is identical even if I blacklist the other wifi card (using an ath5k driver). It's almost like it is using the wrong password or something. Does anyone know what is happening? Is anyone using Ubuntu successful?

  Read the article

• Hybrid Exchange Online setup with on premise public folders, certificate issues?

  - by exxoid

  We have a Hybrid Exchange setup with Exchange Online (v15 tenant) and Exchange 2010 on premise. The hybrid configuration for the most part is working, what I am having an issue with is getting public folders to work for cloud users. I followed the official documentation here (http://technet.microsoft.com/en-us/library/dn249373(v=exchg.150).aspx) and it kind of works. When I am accessing Outlook on a public wifi I am able to bring up the cloud mailboxes and on premise public folders show up in Outlook. When I am accessing email via Outlook as a cloud user on the same LAN as the on premise exchange, the cloud user makes the outlook.com connection for live/ad/archive mailbox but fails to create a proxy connection for the on premise public folders. The error I get is a certificate mismatch, it seems that when a user on the LAN accesses Outlook/Exchange it is using a different certificate vs. when Outlook is launched on a WiFi network. When I look at the Outlook connection information, I see the connection to outlook.com for ad/live/archive mailbox but no entry for public folder connection. Our on premise Exchange is 2010 SP3 with latest CUs. The client is a domain joined laptop with Windows 7 and Office 2010 SP2, latest windows updates applied. Our infrastructure has a working ADFS 3 and DirSync setup for Office 365. My question then is, what do I need to do to make sure that the Cloud user launching Outlook on the LAN uses the proper certificate (the wildcard 3rd party cert.. vs. the self signed certificate which it looks like it may be using during the connection attempt).

  Read the article

• Can't access YouTube

  - by Agentleader1

  I can not seem to connect to YouTube at all. If I connect directly to YouTube (youtube.com) I get this: And if I try to connect via video directly (youtube.com/watch?v=), I get this: Here's how this isn't a web issue: I have malware on my computer I believe. And the question here is, how do I get rid of it, or what possible issue could this be? I can verify this is not a website issue or wifi issue, I've tried to connect on another computer in my wifi, and it worked. It is the local machine issue. I've tried to get rid of malware at my best and also have tried to disable possible virus extensions. All can out as the same result: no help. Also, I am unable to find these hiding viruses. I used malware-bytes and Microsoft Security Essentials. Edit: This is OBVIOUSLY Windows. I am currently running on a laptop Windows 7 Home Premium 4gb ram 64-bit os Lifebook series manufactured by Fujitsu America, Inc. Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz nslookup youtube.com:

  Read the article

• Network bandwidth usage dashboard?

  - by SkippyFlipjack

  I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

  Read the article

• MacMini transmit rate stuck at 11, every other device can connect at full 54Mbit/s?

  - by chum of chance

  I have a MacMini circa 2007 that's getting very low transmit rates via wifi, 8-11. I have other devices that are getting full 54, including a MacBook Air. With everything else off, the MacMini doesn't want to seem to go any faster. Since it has been previously connected to ethernet its entire life, I was wondering if there were some settings I can change to speed up the connection. Option-clicking the network icon gives this read out: PHY Mode: 802.11g Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -73 Transmit Rate: 11 My new MacBook Air has the following readout: PHY Mode: 802.11n Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -66 Transmit Rate: 79 Both have full bars and the wireless router is in the same room to eliminate any obstructions from the equation. Could the MacMini be connecting at an older protocol, like 802.11b and be reporting erroneously that it is connected at 802.11g? This would explain why I haven't seen a transmit rate above 11. Any further trouble shooting I can try before buying a new USB 802.11n device? The WiFi router is a DLink DIR-615. I can see other devices, and none, even the other g connected devices, are getting below 30-40 MBit/s. What's going on here?

  Read the article

• External HDD connecting via USB disconnects wireless LAN connection

  - by Kensai

  Strange problem. I have this MEDION Akoya PC that has a dedicated bay to slide an external HDD sold separately. It's very handy indeed cause the slot is providing a fast USB 3 connection and power to the HDD unit, without extra cables. All works fine except this show-stopper behavior to disconnect me from the router once I slide in the unit and it powers up. The moment I connect the unit the (normally) three-four WiFi connections I see in my neighborhood disappear and my own to the router loses its signal strength (no Internet traffic is possible). After a while it throws me off that one as well, never to connect me again as long as the unit is powered. Once I disconnect the HDD the various signals come back and it automatically reconnects to my own. What takes? Are we in front of a serious design fault by MEDION here? Does the spinning of the HDD on top of the PC cause electromagnetic interference strong enough to throw off my WiFi connectivity? Is it a simple USB problem? Some kind of strange hardware conflict? Where should I look?

  Read the article

• No internet through a web browser but Skype still works

  - by kim3er

  We get our office broadband through a BT Business Broadband WiFi router. We have a mixture of macs and windows PC/laptops connecting to it at any one time. All devices are able to connect to the wireless signal with pretty much full signal. However, only two computers (one windows, one os x) are able to consistently connect to the internet. The other three (one windows, two os x), while they can always connect to the wifi, exhibit one of three characteristics. No internet at all. Programs like Skype work, but no internet through a browser. Internet works, but with intermittent lag when switching between different sites. I'm assuming while trying to resolve different addresses. Ignoring point 1 for moment, my gut is telling me DNS. It is an up to 20MB line that usually gets to between 13MB and 15MB downstream. The router is capable of dealing with the amount of wireless devices that we're throwing at it. Has anyone got any suggestions for how I might further diagnose this problem (preferably in OS X)? Rich

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >