Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 493/600 | < Previous Page | 489 490 491 492 493 494 495 496 497 498 499 500  | Next Page >

• Issues with VPN functionality

  - by Xorandor

  I've been working on setting up VPN connectivity to our office location. We bought a Cisco WRV210 which have a builtin VPN server. Cisco has some software QuickVPN, which is not as quick and easy as I had thought. I've had mixed experiences on different machines with connecting. Instead I configured an IPSec VPN tunnel following a guide from TheGreenBow here http://www.thegreenbow.com/doc/tgbvpn_cg_linksys_wrv200_en.pdf I followed their instructions and tried out an evaluation of their software, and VPN connection should be working ok. I'm able to do RDP to a machine on the network (using IP address, not machine name) and ping the router etc. What I'm trying to solve are two things: It's not like I'm "really" on the network. Or at least I'm restricted to some degree when going through the VPN. I can't access a machine on the network using machine name, only IP. I can't ping a machine, but the router just fine. Could this be that something is not set up properly? If so, I can ofcourse supply additional information. Second, when I log onto the VPN, I would really like my outgoing connection to go through the internet connection of the remote location. Basically if I connect to the VPN I want my outgoing IP to be that of the remote location's (needed for some IP resctrictions on some of our servers). At a previous work location it worked like this when we connected to our office VPN over PPTP and the builtin windows VPN client. I'm not a huge expert on the topic, so any hints will be appreciated.

  Read the article

• Connection refused in ssh tunnel to apache forward proxy setup

  - by arkascha

  I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

  Read the article

• WebHost Manager - Apache's VHost isn't matching the DNS entry

  - by Trans

  I've used CPanel's WebHost Manager to create a new host on my VPS. I then used my HOSTS file to point fake.com to the relevant IP address. The problem I'm having now is, Apache isn't recognizing the VHost,or something, as it's just loading the default entry and 404'ing every document I try to GET. Here's the VHost entry NameVirtualHost 0.0.0.209:80 NameVirtualHost 0.0.0.211:80 <VirtualHost 0.0.0.209:80> ServerName fake.com ServerAlias www.fake.com DocumentRoot /home/fakecom/public_html ServerAdmin [email protected] ## User fakecom # Needed for Cpanel::ApacheConf <IfModule mod_suphp.c> suPHP_UserGroup fakecom fakecom </IfModule> <IfModule !mod_disable_suexec.c> SuexecUserGroup fakecom fakecom </IfModule> CustomLog /usr/local/apache/domlogs/fake.com-bytes_log "%{%s}t %I .\n%{%s}t %O ." CustomLog /usr/local/apache/domlogs/fake.com combined Options -ExecCGI -Includes RemoveHandler cgi-script .cgi .pl .plx .ppl .perl ScriptAlias /cgi-bin/ /home/fakecom/public_html/cgi-bin/ </VirtualHost> I've Google'd this profusely and all that's being returned is 'DNS errors. Wait for it to propagate'. That's obviously not my problem, since I'm using HOSTS. What else could be causing this? :/ EDIT: Forgot to mention. http://fake.com/~fakecom/test.html loads just fine. So the fake.com is pointing to the right IP.

  Read the article

• Network latency and speed of light

  - by James

  This was kinda of covered by the following Is minimum latency fixed by the speed of light? , but i would like to add the follow up a bit. The scenario is as follows; we have two opposing sites one on the West Coast of the US and one in Ireland. The customer is in central Europe, and has requested a latency test. Ireland gives responses of ~65-70ms. However the West Coast guys claim to be faster with a response of 60ms. Now a quick check says that light in fiber would take about 42ms to make the trip to the States and 8.5ms to Ireland. So obviously this is a single hop and does not include routers, switches, firewalls, protocol overhead etc. Would I be right to call BS on their figures? As a final note I tested a ping to Google IP address that was allegedly on the west coast from a site that covered a similar distance and was amazed to get a response time of 20ms. Suggesting ICMP packets that travel twice the speed of light. So A) what am I missing B) Am I right to suspect shenanigans? UPDATE: Guys thanks so far for your help and I have been reading various previous questions on this. About 5 years I had an issue where the hop from the UK to Ireland added 10ms of latency no matter what we did. In the end I moved the servers; So imagine my surprise when I have guys that claim they are 5ms faster with a transatlantic trip. So again should I call BS? Oh and assume both sites are normal mortals that don't have access to Google magical routing, warp dives or flux capacitors. :)

  Read the article

• stdout, stderr, and what else? (going insane parsing slapadd output)

  - by user64204

  I am using slapadd to restore a backup. That backup contains 45k entries which takes a while to restore so I need to get some progress update from slapadd. Luckily for me there is the -v switch which gives an output similar to this one: added: "[email protected],ou=People,dc=example,dc=org" (00003d53) added: "[email protected],ou=People,dc=example,dc=org" (00003d54) added: "[email protected],ou=People,dc=example,dc=org" (00003d55) .######## 44.22% eta 05m05s elapsed 04m spd 29.2 k/s added: "[email protected],ou=People,dc=example,dc=org" (00003d56) added: "[email protected],ou=People,dc=example,dc=org" (00003d57) added: "[email protected],ou=People,dc=example,dc=org" (00003d58) added: "[email protected],ou=People,dc=example,dc=org" (00003d59) Every N entries added, slapadd writes a progress update output line (.######## 44.22% eta 05m05s elapsed ...) which I want to keep and an output line for every entry created which I want to hide because it exposes people's email address but still want to count them to know how many users were imported The way I thought about hiding emails and showing the progress update is this: $ slapadd -v ... 2>&1 | tee log.txt | grep '########' # => would give me real-time progress update $ grep "added" log.txt | wc -l # => once backup has been restored I would know how many users were added I tried different variations of the above, and whatever I try I can't grep the progress update output line. I traced slapadd as follows: sudo strace slapadd -v ... And here is what I get: write(2, "added: \"[email protected]"..., 78added: "[email protected],ou=People,dc=example,dc=org" (00000009) ) = 78 gettimeofday({1322645227, 253338}, NULL) = 0 _######## 44.22% eta 05m05s elapsed 04m spd 29.2 k/s ) = 80 write(2, "\n", 1 ) As you can see, the percentage line isn't sent to either stdout or stderr (FYI I have validated with known working and failing commands that 2 is stderr and 1 is stdout) Q1: Where is the progress update output line going? Q2: How can I grep on it while sending stderr to a file? Additional info: I'm running Openldap 2.4.21 on ubuntu server 10.04

  Read the article

• PostgreSQL pg_hba.conf with "password" auth wouldn't work with PHP pg_connect?

  - by tftd

  I've recently experimented with the settings in pg_hba.conf. I read the PostgreSQL documentation and I though that the "password" auth method is what I want. There are many people that have access to the server PostgreSQL is working on so I don't want the "trust" method. So I changed it. But then PHP stopped working with the database. The message I get is "Warning: pg_connect(): Unable to connect to PostgreSQL server: FATAL: password authentication failed for user "myuser" in /my/path/to/connection/class.php on line 35". It is kind of strange because I can connect via phppgadmin without any problems and also I can connect from my home computer with psql - again without any problems. This is my pg_hba.conf: # TYPE DATABASE USER CIDR-ADDRESS METHOD # "local" is for Unix domain socket connections only local all all password # IPv4 local connections: host all all 127.0.0.1/32 password # IPv6 local connections: host all all ::1/128 password The connection string I'm using with pg_conenct is: $connect_string = "host=localhost port=5432 dbname=mydbname user=auser password=apassword"; $dbConnection = pg_connect($connection_string); Does anybody know why is this happening ? Did I misconfigured something ?

  Read the article

• Need help using a super scope

  - by Vdub

  I have a windows server 2008 r2 standard running our DCHP, DNS, and AD. also I have (3) HP Pro Curve 2510-G switches (J9280A). Right now our LAN is set up 192.168.50.2-192.168.50.254 on our sub-net (A) and another scope with 192.168.51.2-192.168.51.254 sub-net (B) both have sub-net mask of 255.255.255.0. The same server is our DNS which is 192.168.50.242 and our firewall (watchguard) is the gateway at 192.168.50.1. Right now the sub-net (B) does not have DHCP active so only sub-net (A) is giving a pool. My problem is that we are trying to have open WiFi on our network and i am assuming that i can use the sub-net (B) for that if i activate it and use sub-net (A) for our staff only. I have noticed that when i set up a static on a client pc and set it to 192.168.51.x i cannot use the DNS of 192.168.50.242 however i can use 8.8.8.8 and it works fine, i am guessing that because it is on a different sub-net? Forgive me as i am very new at this and dont know a lot. Is there easy way with the equipment i have to a accommodate wifi for hundreds of people without causing problems for our staff? (multiple same IP address assigns) I appreciate any and all info!

  Read the article

• KVM error with device pass through

  - by javano

  I am running the following command booting a Debian live CD passing a host PCI device to the guest as a test and KVM errors out; kvm -m 512 -boot c -net none -hda /media/AA502592502565F3/debian.iso -device pci-assign,host=07:00.0 PCI region 1 at address 0xf7920000 has size 0x80, which is not a multiple of 4K. You might experience some performance hit due to that. No IOMMU found. Unable to assign device "(null)" kvm: -device pci-assign,host=07:00.0: Device 'pci-assign' could not be initialized lspci | grep 07 07:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74) I shoved an old spare NIC into my motherboard to test PCI pass through. I have searched the Internet with Goolge and found that errors relating to "No IOMMU found" often mean the PCI device is not supported by KVM. Does KVM have to support the device being "passed-through"? I though the point was to pass the device through and let the guest worry about it? Ultimately I want to pass-through a PCI random number generator, is this not going to be possible with KVM? Thank you.

  Read the article

• One-To-Many Powershell Scripts

  - by Matt

  I'm trying to create a script to run as a scheduled task, which will run against multiple servers and retrieve some information. To start with, I populate the list of servers by querying AD for all servers that match a certain set of criteria, using Get-ADComputer. The problem is, the list is returned as an object, which I can't then pass to the New-PSSession list. I have tried converting it to a comma-seperated string by doing the following: foreach ($server in $serverlist) {$newlist += $server.Name + ","} but this still doesn't work. the alternative is to iterate through the list and run the various commands against each server one at a time, but my preference would be to avoid this and run them using one-to-many remoting. UPDATE: To clarify what I want to end up being able to do is using -ComputerName $serverlist, so I want $serverlist to be a string rather than an object. UPDATE 2: Thanks for all the suggestions. Between them and my original method I'm starting to wonder whether -ComputerName can accept a string variable? I've got varying degrees of success getting the list of computers converted to a comma separated string, but no matter how I do it I always get invalid network address.

  Read the article

• Does MySQL have some kind of DoS protection or per-user query limit?

  - by Ghostrider

  I'm a bit at a loss. I'm running a MySQL database that's roughly 1GB data in indices combined on a dedicated Linux server. DB version is '5.0.89-community'. Configuration is controlled via cPanel. PHP actually runs elsewhere on a shared hosting. IP addresses are static and don't change. Access from remote IP address is properly configured. Website gets around 10K hits per day with each hit generating a a database query. Some of these queries are expensive (~1 sec execution time). All is fine and well until at some point DB server starts refusing connections from the client, claiming that specific user can't access the server from that IP. Resetting the server will always fix the problem for a day or two and then the same thing happens. There are some other DBs on that server, some of which are hit pretty hard on occasion but constantnly. One of the apps maintains several persistent connections since it does couple of updates per minute. Though I don't think it's related. What's driving me mad is that I can't figure out why server would start refusing connections. There is nothing in the logs. This server is a hosted dedicated server so hosting company created the OS image and I didn't write or go over every line of configuration. I'd do it but I'm at a loss as to where start looking. Any advice is appreciated.

  Read the article

• python reports socket in use, netstat and others claim its not

  - by captainmish

  We have a strange socket issue with a RHES3 box: Python 2.4.1 (#1, Jul 5 2005, 19:17:11) [GCC 3.2.3 20030502 (Red Hat Linux 3.2.3-52)] Type "help", "copyright", "credits" or "license" for more information. >>> import socket >>> s = socket.socket() >>> s.bind(('localhost',12351)) Traceback (most recent call last): File "<stdin>", line 1, in ? File "<string>", line 1, in bind socket.error: (98, 'Address already in use') This seems normal, lets see what has that socket: # netstat -untap | grep 12351 {no output} # grep 12351 /proc/net/tcp {no output} # lsof | grep 12351 {no output} # fuser -n tcp 12351 {no output, repeating the python test fails again} # nc localhost 12351 {no output} # nmap localhost 12351 {shows port closed} Other high ports work fine (eg 12352 works) Is there something magic about this port? Is there somewhere else I can look? Where does python find out that socket is in use that netstat doesnt know about? Any other way I can find out what/if that socket is?

  Read the article

• Setup Entourage for Exchange via HTTP communication

  - by Johandk

  Our ISP set up a hosted exchange server for all our mail. I've setup all our Outlook users with no problems. We have two people using Mac OSX Leopard and Entourage. Entourage has the option of adding an Exchange account, but I have no idea how to tell it to connect to exchange via HTTP. Heres an excerpt from the client setup docs the hosting company sent me for Outlook: 1 .Go to control panel 2. Select ‘Mail’ 3. Select ‘Email accounts’ Under the E-mail tab select ‘New’ Select ‘Manually configure server settings......’ - click next Select ‘Microsoft Exchange’ – click next Complete details as below with Microsoft Exchange Server as: [server address] Do not select ‘Check Name’. Instead select ‘More Settings’. Go to the Connection tab, and select the bottom option ‘Connect to Microsoft Exchange using HTTP’. And then select the ‘Exchange Proxy Settings’ button. Enter Proxy server for Exchange Check Only connect to proxy servers that have this principal name in their certificate, Enter msstd:[servername] Proxy Authentication - select Basic Authentication Select OK, and again, so that you return to the main screen. Now select ‘Check Name’. Enter Username and Password: The username should now be the full name and underlined. If so select next, and then finish. Next time you open Outlook, enter username and password Any help GREATLY appreciated.

  Read the article

• Can I use multiple URLs in the URL field of KeePass?

  - by Sammy

  I am using KeePass version 2.19. What I would like to do is have more than just one URL address associated with a given user name and password. The entry for a given website might look something like this... Title google User Name email Password pass URL https://accounts.google.com/ServiceLogin?hl=en&continue=https://www.google.com/ https://accounts.google.com/ServiceLogin?hl=sv&continue=https://www.google.com/ https://accounts.google.com/ServiceLogin?hl=de&continue=https://www.google.com/ As you can see the ?hl=en changes into ?hl=sv and then to ?hl=de for the three different languages in which I wish to view the Google log-in page. But this of course could be something completely different, like different web services from the same provider like YouTube and Gmail by Google. Very much like SE where you have several websites but only use one user name and password. I imagine something along the lines of having multiple entries for one and the same website, where KeePass would actually prompt you to choose which one you want to use. So you have several user names and passwords that use the same URL. But is it possible to have several URLs using the same user name and password, so that KeePass asks me "to which of the following three URLs do you want to auto-log into with this password"?

  Read the article

• Intermittent 5.7.1 email bounce to Exchange 2007

  - by Steve Kennaird

  My knowledge of Exchange isn't particularly great, so excuse me if some of the terminology I use isn't quite right. I'm primarily a web developer who's now responsible for a small business's network. We have a server running SBS 2008 and Exchange 2007. Generally, everything works well, emails are able to be sent to both internal and external domains without issue. We've only got ~20 users, Exchange is sitting on a single server. I use SendGrid to send emails generated by our externally hosted website to users in the office. Primarily, order notifications are sent to [email protected]. Without any pattern and less than once per week on average, an email to [email protected] will bounce back, and the logs on SendGrid detail the following error: 550 5.7.1 Unable to relay for [email protected] Either side of that failed delivery attempt, I'm able to send and receive emails to/from [email protected]. Having done some research, incorrect reverse DNS seems like it could be a cause of intermittent bounces like this. Having used nslookup, I have found that the reverse DNS doesn't map like it should, e.g. Office IP: 135.325.351.123 (made up IP, for example only) Domain: office.somedomain.com (made up, for example only) Reverse DNS: somedomain.gotadsl.co.uk (half made up) Could this be a cause? I'm sure that the IP address and the domain should map to each other. Also, it has been suggested to me that as the Exchange server is on a network with an ADSL connection, that could be a potential cause as the connection "goes up and down all day long". I don't have an opinion on this, as I don't have enough knowledge of Exchange/ADSL to form a reliable opinion. Can anyone offer any insight as to whether one or both are actually potential causes, or if there is another possible cause?

  Read the article

• Why is 32-bit-mode required in IIS7.5 for my app?

  - by Jonas Lincoln

  I have a .net4 web application running in a 64 bits 2008 server. I can only get it to run when I set the app pool to Enable 32-bits application to true. All dlls are compiled for .net4 (verified with corflags.exe). How can I figure out why Enable 32-bit is required? The error message from the event log when starting as a 64-bit app-pool Event code: 3008 Event message: A configuration error has occurred. Event time: 2011-03-16 08:55:46 Event time (UTC): 2011-03-16 07:55:46 Event ID: 3c209480ff1c4495bede2e26924be46a Event sequence: 1 Event occurrence: 1 Event detail code: 0 Application information: Application domain: removed Trust level: Full Application Virtual Path: removed Application Path: removed Machine name: NMLABB-EXT01 Process information: Process ID: 4324 Process name: w3wp.exe Account name: removed Exception information: Exception type: ConfigurationErrorsException Exception message: Could not load file or assembly 'System.Data' or one of its dependencies. An attempt was made to load a program with an incorrect format. at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) at System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() at System.Web.Configuration.AssemblyInfo.get_AssemblyInternal() at System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection compConfig) at System.Web.Compilation.BuildManager.CallPreStartInitMethods() at System.Web.Hosting.HostingEnvironment.Initialize(ApplicationManager appManager, IApplicationHost appHost, IConfigMapPathFactory configMapPathFactory, HostingEnvironmentParameters hostingParameters, PolicyLevel policyLevel, Exception appDomainCreationException) Could not load file or assembly 'System.Data' or one of its dependencies. An attempt was made to load a program with an incorrect format. at System.Reflection.RuntimeAssembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, RuntimeAssembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoadAssemblyName(AssemblyName assemblyRef, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoad(String assemblyString, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) at System.Reflection.Assembly.Load(String assemblyString) at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) Request information: Request URL: "our url" Request path: "url" User host address: ip-adddress User: Is authenticated: False Authentication Type: Thread account name: "app-pool" Thread information: Thread ID: 6 Thread account name: "app-pool" Is impersonating: False Stack trace: at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) at System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() at System.Web.Configuration.AssemblyInfo.get_AssemblyInternal() at System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection compConfig) at System.Web.Compilation.BuildManager.CallPreStartInitMethods() at System.Web.Hosting.HostingEnvironment.Initialize(ApplicationManager appManager, IApplicationHost appHost, IConfigMapPathFactory configMapPathFactory, HostingEnvironmentParameters hostingParameters, PolicyLevel policyLevel, Exception appDomainCreationException) Custom event details:

  Read the article

• SQL Server Remote Connections

  - by Barry

  Hi, I am at my wits end with trying to access a remote SQL Server 2008 R2 Express instance. Here are the following that I have tried. 1) I enabled remote connections in the instance properties. 2) I enabled sql server and windows authentication mode and created an account to log in using sql server authentication. 3) I started the SQL Server Browser service 4) I forwarded ports 1433 and 1434 on the router to the IP address of the machine hosting SQL Server. 5) I turned off firewalls on both the Machine running the instance and the router. 6) http://www.yougetsignal.com/tools/open-ports/ I used this to check whether or not both ports were open and it says that they are closed. I have the SQL Server Express instance running and the browser running. I have configured it to allow remote connections yet, it tells me they are both closed. I'm pretty confused at this stage. On the client Machine I am trying to connect using the following format machineip\SQLEXPRESS with SQL Server Management Studio Express. Thanks in advance

  Read the article

• How to send email from home ip when the email server isn't a designated outbound mail server allocated to BT Retail customers [on hold]

  - by Mr Shoubs

  (I am sys admin!) I can receive email, but when I try to send an email from my home office via our work email server I get the following reply: Your message did not reach some or all of the intended recipients. Subject: Test Sent: 19/08/2014 17:02 The following recipient(s) cannot be reached: 'Joe Blogs' on 19/08/2014 17:02 Server error: '554 5.7.1 Service unavailable; Client host [my-ip-here] blocked using zen.spamhaus.org; http://www.spamhaus.org/query/bl?ip=my-ip-here' I went to that URL and it says the following: Ref: PBL231588 81.152.0.0/13 is listed on the Policy Block List (PBL) Outbound Email Policy of BT Retail for this IP range: It is the policy of BT Retail that unauthenticated email sent from this IP address should be sent out only via the designated outbound mail server allocated to BT Retail customers. Please consult the following URL for details on how to configure your email client appropriately. http://btybb.custhelp.com/cgi-bin/btybb.cfg/php/enduser/cci/bty_adp.php?p_sid=fPnV4zhj&p_faqid=6876 Removal Procedure Removal of IP addresses within this range from the PBL is not allowed by the netblock owner's policy. Going to this URL just says: This site has been disabled for the time being. Does anyone know what I should do to allow me to send emails from my home ip - the site suggests I can configure my email client? (note that I have configured the client to use smtp authentication)

  Read the article

• MX setup for a domain registrar and web host with the same domain name

  - by Honus Wagner

  I have a client that has registered their domain through a registrar, then signed up for hosting on through a different provider, but used the same domain for said provider (didn't re-register the domain, I think the declaration of domain on the host was for CNAME records specifically). The registrar properly routes his emails at his domain name (email hosted by Google), but the problem is, on the hosted site, when an administration action occurs, he is supposed to get an email stating so. The site is sending him an email with PHP and he never receives an email when its to his address with the same domain name; all other domain addresses work just fine. I have to imagine its something misconfigured on the host. From what I can assume, I think that the host sees that the to and from domains are the same, and it decides not to route the email externally. Currently, the registrar uses the proper nameservers for the host, and there are MX records on both the registrar and the host (they are identical entries). I hope I've been clear in my question. If you need further clarification, or additional information of any kind, I can provide it. Thanks in advance.

  Read the article

• SQL Server Remote Connections

  - by Barry

  Hi, I am at my wits end with trying to access a remote SQL Server 2008 R2 Express instance. Here are the following that I have tried. 1) I enabled remote connections in the instance properties. 2) I enabled sql server and windows authentication mode and created an account to log in using sql server authentication. 3) I started the SQL Server Browser service 4) I forwarded ports 1433 and 1434 on the router to the IP address of the machine hosting SQL Server. 5) I turned off firewalls on both the Machine running the instance and the router. 6) http://www.yougetsignal.com/tools/open-ports/ I used this to check whether or not both ports were open and it says that they are closed. I have the SQL Server Express instance running and the browser running. I have configured it to allow remote connections yet, it tells me they are both closed. I'm pretty confused at this stage. On the client Machine I am trying to connect using the following format machineip\SQLEXPRESS with SQL Server Management Studio Express. Thanks in advance

  Read the article

• AWS VPC ELB vs. Custom Load Balancing

  - by CP510

  So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

  Read the article

• Outlook VBA script - find and replace text with image

  - by user2530616

  I have a e-commerce store. When I get a sale, I receive an order confirmation email which contains the name of the product sold. When the email comes through, I would like to run a script that replaces the product name eg. "red widget", with a picture of that product. Is that possible? I have found a similar code to replace text (set of numbers in this case) with a link, but I need it to replace with a picture instead. Option Explicit Sub InsertHyperLink(MyMail As MailItem) Dim body As String, re As Object, match As Variant body = MyMail.body Set re = CreateObject("vbscript.regexp") re.Pattern = "#[0-9][0-9][0-9][0-9][0-9][0-9]" For Each match In re.Execute(body) body = Replace(body, match.Value, "http://example.com/bug.html?id=" & Right(match.Value, 6), 1, -1, vbTextCompare) Next MyMail.body = body MyMail.Save End Sub example mail Order Confirmation Thanks for shopping with us today! ------------------------------------------------------ Order Number: 2209 Date Ordered: Friday 28 June, 2013 Products ------------------------------------------------------ 1 x red widget = $5.00 ------------------------------------------------------ Total: $0.00 Delivery Address xxx search text: "red widget" replace picture: redwidget.jpg

  Read the article

• For enabling SSL for a single domain on a server with muliple vhosts, will this configuration work?

  - by user1322092

  I just purchased an SSL certificate to secure/enable only ONE domain on a server with multiple vhosts. I plan on configuring as shown below (non SNI). In addition, I still want to access phpMyAdmin, securely, via my server's IP address. Will the below configuration work? I have only one shot to get this working in production. Are there any redundant settings? ---apache ssl.conf file--- Listen 443 SSLCertificateFile /home/web/certs/domain1.public.crt SSLCertificateKeyFile /home/web/certs/domain1.private.key SSLCertificateChainFile /home/web/certs/domain1.intermediate.crt ---apache httpd.conf file---- ... DocumentRoot "/var/www/html" #currently exists ... NameVirtualHost *:443 #new - is this really needed if "Listen 443" is in ssl.conf??? ... #below vhost currently exists, the domain I wish t enable SSL) <VirtualHost *:80> ServerAdmin [email protected] ServerName domain1.com ServerAlias 173.XXX.XXX.XXX DocumentRoot /home/web/public_html/domain1.com/public </VirtualHost> #below vhost currently exists. <VirtualHost *:80> ServerName domain2.com ServerAlias www.domain2.com DocumentRoot /home/web/public_html/domain2.com/public </VirtualHost> #new -I plan on adding this vhost block to enable ssl for domain1.com! <VirtualHost *:443> ServerAdmin [email protected] ServerName www.domain1.com ServerAlias 173.203.127.20 SSLEngine on SSLProtocol all SSLCertificateFile /home/web/certs/domain1.public.crt SSLCertificateKeyFile /home/web/certs/domain1.private.key SSLCACertificateFile /home/web/certs/domain1.intermediate.crt DocumentRoot /home/web/public_html/domain1.com/public </VirtualHost> As previously mentioned, I want to be able to access phpmyadmin via "https://173.XXX.XXX.XXX/hiddenfolder/phpmyadmin" which is stored under "var/www/html/hiddenfolder"

  Read the article

• My URL has been identified as a phishing site

  - by user2118559

  Some months before ordered VPS at Ramnode According to tutorial (ZPanelCP on CentOS 6.4) http://www.zvps.co.uk/zpanelcp/centos-6 Installed CentOS and ZPanel) Today received email We are requesting that you secure and investigate the phishing website identified below. This URL has been identified as a phishing site and is currently involved in identity theft activities. URL: hxxp://111.11.111.111/www.connet-itunes.fr/iTunesConnect.woasp/ //IP is modified (not real) This site is being used to display false or spoofed content in an apparent effort to steal personal and financial information. This matter is URGENT. We believe that individuals are being falsely directed to this page and may be persuaded into divulging personal information to a criminal, if the content is not immediately disabled. Trying to understand. Some hacker hacked VPS, placed some file (?) with content that redirects to www.connet-itunes.fr/iTunesConnect.woasp? Then questions 1) how can I find the file? Where it may be located? url is URL: hxxp://111.11.111.111/ IP address, not domain name 2) What to do to protect VPS (with CentOS)? Any tutorial? Where may be security problem? I mean may be someone faced something similar....

  Read the article

• Change the order of IP addresses returned by ifconfig?

  - by erikcw

  I have an Ubuntu server with several IP addresses attached to it. 127.0.0.1 is listed as venet0 by ifconfig. I'm using Chef to configure the server. The problem is that chef is listing 127.0.0.1 as the IP address for the server instead of one of the server's "real" IPs. (apparent "ohai ipaddress" uses the first IP listed by ifconfig to determine the server's IP). How can I change the order so the servers main IP is listed first instead of the 127.0.0.1? Can venet0 be deleted and venet0:0 be "promoted" to take its place since 127.0.0.1 is already listed in the "lo" interface? lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16700 (16.7 KB) TX bytes:16700 (16.7 KB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:7622207 errors:0 dropped:0 overruns:0 frame:0 TX packets:8183436 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2102750761 (2.1 GB) TX bytes:2795213667 (2.7 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX1 P-t-P:XXX.XXX.XXX.XX1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX2 P-t-P:XXX.XXX.XXX.XX2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 route -n route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 venet0 0.0.0.0 192.0.2.1 0.0.0.0 UG 0 0 0 venet0

  Read the article

• Problem routing between directly connected Subnets w/ ASA-5510

  - by Zephyr Pellerin

  This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

  Read the article

< Previous Page | 489 490 491 492 493 494 495 496 497 498 499 500  | Next Page >