Search Results

Search found 29064 results on 1163 pages for 'network management'.

Page 496/1163 | < Previous Page | 492 493 494 495 496 497 498 499 500 501 502 503  | Next Page >

• Change authentication wifi WPA to WEP on Windows 8

  - by Kites

  I use netsh wlan set hostednetwork mode=allow ssid=Kites key=phambaoViet netsh wlan start hostednetwork To share WiFi from LAN network on laptop (Windows 8) to my other device. When I show information netsh wlan show hostednetwork the supported authentication is WPA. My device support authentication WEP only. How can I change the authentication to WEP? Infomation: Interface name: Wi-Fi Driver : Qualcomm Atheros AR9002WB-1NG Wireless Network A dapter Vendor : Qualcomm Atheros Communications Inc. Provider : Microsoft Date : 03/07/2012 Version : 3.0.0.130 INF file : C:\Windows\INF\netathrx.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g 802.11n FIPS 140-2 mode supported : Yes 802.11w Management Frame Protection supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Vendor defined Vendor defined Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP Vendor defined Vendor defined

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• ESXi 5.1 on Poweredge 510 freezes after base-esx update

  - by goober

  Background / Problem Just experienced an issue where an ESXi host was upgraded from 5.0 -- 5.1 perfectly fine. Then, I did a scan and remediated a patch (ESXi510-201210401-BG) Looking into the host on via the kvm switch, this appears to complete successfully. However, on reboot, the server hangs at the "Initializing Power Management" phase. I've read from various spots around the internet that this usually clears itself up again upon a cold boot, but given that our servers are in a different building with different access rules, the less I have to physically go there, the better. :) Question Is there anything I can do to avoid an ESXi host hanging at the "initialize power management" phase of boot after remediating the host to apply patches?

  Read the article

• Any ideas for automatic initial/scripted configuration of a NetApp?

  - by maddenca

  The background is to make a solution where we can automate as much as possible the building up of ‘pods’ that include server/network/storage and that will be built at remote sites. In an ideal world would be that we create a single management server which is preconfigured with DHCP/TFTP/or whatever. This management server is racked with a CISCO UCS, FAS31x0, etc. at a build site and is then transported to the final customer site where on power it almost configures itself, or at least bootstraps itself far enough that a remote skilled 'expert' can complete the setup of the pod. Ideas (doesn't have to resemble 100% of the above) would be helpful.

  Read the article

• Cannot connect with Cisco VPN but can connect with ShrewSoft VPN

  - by rodey

  EDIT: We connected an air card to the computer to use a different Internet connection and using the Cisco software, we were able to successfully connect to our VPN server. I just don't understand why the ShrewSoft VPN client would connect but the Cisco connection won't. I'm not our network admin so sorry if I butcher some of the terminology. I have a computer at remote site that connects to our network through Cisco VPN. It uses the Cisco VPN software to do so. The problem is that the computer at this site cannot connect to our VPN because it is getting error "Reason 412: The remote peer is no longer responding." To see if perhaps something on their network was blocking the connection, I installed the ShrewSoft VPN client on the computer, imported our .pcf file and connected with no problem. I have tried two different versions of the Cisco VPN software (4.8.0.* and 5.0.03.*) and have the same problem. I installed Wireshark on the computer and have confirmed (while trying to connect through Cisco) that the computer is trying to contact the VPN server but is not receiving a response. We are not having any other problems regarding users not being able to connect. I'm at a loss at what else to check. I'll be monitoring this and have access to the computer at any time.

  Read the article

• How to enabled Printer Sharing on Web Server 2008?

  - by FarrEver

  I am installing Web Server 2008 for my home network. I have 2 USB printers that I am connecting to this machine and want to share these printers so that my other machines can print to these 2 USB printers. (I previously had Win Server 2003 on this machine and was able to share both printers fine.) File and Printer sharing Inbound Role for my Private network is enabled, when I go into Network and Sharing Center and try to turn ON Printer Sharing, it never sticks. It always stays on OFF. I go to my installed printers and try to Share them and get the following error message: Printer Settings could not be saved. Remote connections to the Print Spooler are blocked by a policy set on your machine. I have not been able to find a policy on my machine that is preventing this. I have searched a lot over the past few days and most of the results say what I have done should work and there are also a number of search results that say Printer Sharing on Web Server 2008 is not allowed and you have to hack it. Has anyone installed Web Server 2008 and shared printers before? If so, what are the detailed steps you took to get this to work?

  Read the article

• Why is my HDD not showing up?

  - by Mike

  I'm on Windows 7, got a new 2 TiB NON-external hard disk. When I plug it in it doesn't show up on the Disk Management list in the Computer Management window (that you get by right-clicking My Computer and selecting "Manage"). At first I thought it was broken, but I could see it using a friend's computer. I've run a full disk scan using the official tool from Western Digital, no problems. I've formatted it and partitioned it at another friends place, I've even encrypted the disk fully without any problems, then mounted it and placed a text file on it with the word "hello" inside and saved the file. When I boot my own computer the disk shows up in BIOS. So the disk is not broken. I've tried changing what SATA slot on the motherboard I stick it in. Makes no difference. After all this: Why won't my Windows 7 discover the disk???

  Read the article

• Wake on Lan/Wan won't work after some time has passsed

  - by Vian Esterhuizen

  I have the following set up: Gigabyte Z77X-UD5H Wake On Lan Enabled Asus N66U Port Forwarding Static IP assigned to my computer Windows 7 Advanced Power Management - PCI Express - Off Intel 82579V - All options under Power Management checked I'm trying to set this up for Wake on Wan capabilities. If I shut down my computer and immediately try to Wake on Wan (and Lan) it works and starts up. While the computer is on, I've used a few WOL specific packet sniffers and the packet comes through on the correct port. After any period of time over a few minutes, waking on Wan or Lan won't work. The back "activity" light is blinking on my ethernet port on my computer, as well as on the router, so I would assume the network card is on and able to receive a signal. Any ideas? Suggestions? What can I do to troubleshoot the problem?

  Read the article

• Cisco ASA 5510 Time of Day Based Policing

  - by minamhere

  I have a Cisco ASA 5510 setup at a boarding school. I determined that many (most?) of the students were downloading files, watching movies, etc, during the day and this was causing the academic side of our network to suffer. The students should not even be in their rooms during the day, so I configured the ASA to police their network segment and limit their outbound bandwidth. This resolved all of our academic issues, and everyone was happy. Except the resident students. I have been asked to change/remove the policing policy at the end of the day, to allow the residents access to the unused bandwidth at night. There's no reason to let bandwidth sit unused at night just because it would be abused during the day. Is there a way to setup Time of Day based Policies on the ASA? Ideally I'd like to be able to open up the network at night and all day during weekends. If I can't set Time based policies, is is possible to schedule the ASA to load a set of commands at a specific time? I suppose I could just setup a scheduled task on one of our servers to log in and make the changes with a simple script, but this seems like a hack, and I'm hoping there is a better or more standard way to accomplish this. Thanks. Edit: If there is a totally different solution that would accomplish a similar goal, I'd be interested in that as well. Free/Cheap would be ideal, but if a separate internet connection is my only other option, it might be worth fighting for money for hardware or software to do this better or more efficiently.

  Read the article

• USB to IDE/SATA adapter

  - by unknown (google)

  I have an old IDE HDD that I am trying to pull files off of. I am using a USD to IDE/SATA adapter. I plug in the power and adapter plugs into the drive and it fires up. I plug the USB plug into my XP laptop and it installs the drivers. I can see USB Mass Storage Device under Device Manager. My problem is I can't see the drive in either Windows Explorer or under Disk Management under Computer Management. Not sure what I am doing wrong. Do I have to slave the old hdd? Do I have to make BIOS changes?

  Read the article

• Make case-sensitive SMB share case-insensitive

  - by fungs

  I am running a legacy XP app that I would like to move on a network share. It is very simple and works in theory but the server providing the share is based on Linux (cannot configure) and the software does not work correctly because it is programmed case-insensitively, it seems. After some research, network shares behave like the filesystem they use underneath. This is normal. Unfortunately I cannot fix the software myself. Is there any way to turn the case-sensitivity into case-insensitivity for a Windows network drive on the client side? I fould two approaches: First, something like icasefile (http://wnd.katei.fi/icasefile/) that wraps around the program and intercepts the file I/O. This is for UNIX only. Secondly, a proxy virtual file system (e. g. something using Dokan). Unfortunately I couldn't find any suitable fs, the only possibility would be to put a case-insensitive filesystem on an image file and put this on the share using for example lmdisk (http://www.ltr-data.se/opencode.html/#ImDisk). Do you have any better ideas?

  Read the article

• VMWare converter performance

  - by bellocarico

  Hello, I have a question about my test lab. It's more to understand the concept more than apply this into production: I have an ESXi with few VMs linux/windows configured and I'd like to use VMWare converter to create backups. To speedup the process I decided to create a Windows VM on the same ESXi host where I've installed Windows 7 and VMWare Converter. The Host has a gigabit card but it's currently connected to a 100Mb FD port. Windows 7 sees a 1gb card connected. When I do the backup using VMWare converter I specify the host IP as source and destination, so I thought the copy could be faster then use my laptop across the network. Well, to cut a long sotry short: I get dreadful performance (4Mb/sec). I'm a buit confused on this because despite the fact that the host is running 100Mb communication between VMs and hosts shouldn't (correct me if I'm wrong) have any limitation instead. I did tweak windows 7 to optimise network performane but I got just a little improvement. i still need 4 hours to back up a 50Gb (thin) VM. Additionally I wanted to ask: Would jumbo frame help in this? I know that jumbo frame have to be supported end to end, and the network switch where the host is currently connected doesn't support this, but I was wondering: 1) Does ESXi host support jumbo frames at all? 2) Can I enable it somehow? 3) If I do so, I guess bulk transfert between VMs and host would improve, but would this affect the communication going through the real switch as this doesn't do jumbo? Thanks for reading

  Read the article

• Using proxy.pac to access Apache 2 with a hostname?

  - by leeand00

  Note that I do not have a DNS on my network, and that is why I am resorting to using a proxy.pac file. I would like to be able to access my development Apache 2 server using a name instead of an ip without setting up a full blown DNS. I am aware of setting names in the C:\Windows\System32\drivers\etc\hosts file and the /etc/hosts files, however I cannot edit the hosts file on all of the devices that I am testing the site on. I've added a proxy.pac file to my Apache2 server and pointed my browsers settings to it at: http://192.168.2.221/proxyutils/proxy.pac ...where 192.168.2.221 is thehostname's ip address. I set the above URL in Firefox in the following manner: From the menubar selecting "Edit-Preferences" In the resulting "Firefox Preferences" window clicking the "Advanced" tab. Clicking the "Network" tab Clicking the "Settings" button. Selecting the "Automatic proxy configuration URL:" radio button. Entering http://192.168.2.221/proxyutils/proxy.pac and pressing OK. The contents of the proxy.pac file on the Apache server function FindProxyForURL(url, host) { if( dnsDomainIs(host, "thehostname") ) return "PROXY 192.168.2.221:80"; return "DIRECT"; } In Firefox I then access the following URL: http://thehostname/wp-blog/ And instead of the development version of the Wordpress blog I am trying to access I get a URL of http://thehostnamehttp/thehostname/wp-blog/ in my address bar and a 404 Not Found page in the browser window. Looking over proxy.pac, it seems like calling dnsDomainIs shouldn't work considering I don't have a DNS setup on my network, but I've also tried just comparing the host argument with the string "hostname" and it yielded the same result, even after modifying the proxy.pac file and clicking the reload button near the proxy settings. This could also be a Wordpress problem, since I've noticed that directories without Wordpress seem to function perfectly normally. (see cross post here) Is there any way I can modify my configuration so that I can access the site using http://thehostname/wp-blog/ ?

  Read the article

• Possible to IPSec VPN Tunnel Public IP Addresses?

  - by caleban

  A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

  Read the article

• ZFS and SAN -- best practices?

  - by chris

  Most discussions of ZFS suggest that the hardware RAID be turned off and that ZFS should directly talk to the disks and manage the RAID on the host (instead of the RAID controller). This makes sense on a computer with 2-16 or even more local disks, but what about in an environment with a large SAN? For example, the enterprise I work for has what I would consider to be a modest sized SAN with 2 full racks of disks, which is something like 400 spindles. I've seen SAN shelves that are way more dense than ours, and SAN deployments way larger than ours. Do people expose 100 disks directly to big ZFS servers? 300 disks? 3000 disks? Do the SAN management tools facilitate automated management of this sort of thing?

  Read the article

• Vlans and subinterfaces

  - by Adeodatus

  I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

  Read the article

• Firebox 1250e Core Failing?

  - by Noah

  We have 2 Firebox 1250e Core firewall boxes in our production environment, serving as an active and passive mode. A few months back, the active box was flashing a warning light, so our consultant removed it, and plugged it in to a test network. Everything appeared to be working fine, so he reloaded it into the production environment, and we didn't see any other issues. Fast forward to last week, and out network was constantly dropping connections over RDC, timing out, and performing as if there was a traffic issue. I turned off the production box and everything began to work fine immediately. At this point though, I'm not sure how to proceed. Should the box be completely replaced? Is there any recommended testing we could do to determine if there is a failure of some type with this device? Should we try upgrading the software on it? I know the environment isn't the issue, since the passive box (which is now the active one) is working fine. We'd like to have 2 in production though for safety failover purposes. I am not a network admin, but am hoping someone here might be able to provide some guidance.

  Read the article

• How can I change the default location/action of 'Open Outlook Data File' in Outlook 2010?

  - by Chadddada

  I have recently deployed a Remote Desktop Host server that functions as a remote Microsoft Office 2010 work space for users. In part of the locking down of this server I have installed all programs on the D: drive and, through the use of Group Policy, hidden all the drives on the server from standard users. In addition to hiding these drives I am not allowing users to save anything locally (on the server) or open Libraries. However one of the functions of the server is to provide the Outlook client. Often users will have the .PST file stored on a network location and want to open this in Outlook. Can I change the default action or location that File Open Open Outlook Data File looks or tries to pull the file from? The default location seems to be under Users / Libraries. When click 'Open' you get a warning: This operation has been cancelled due to restrictions in effect on this computer. Clicking OK drops the user into a small menu that shows attached network drives under Computer. Can I instead have the 'Open' click drop the users in a defined network drive or just open computer and allow them to select a share? I don't want them to see the error message. A solution that looks to have been used for Office 2000/03 is: Key: HKEY_CURRENT_USER\Software\Microsoft\Office\<version>\Outlook Value name: ForceOSTPath Value type: REG_EXPAND_SZ Value: path to your storage folder I am not sure if there is a better way to do this now OR if this even works with Office 2010.

  Read the article

• Can't connect remotely to Windows Server 2008 R2

  - by JohnyD

  I have a new Dell R710 server running Windows Server 2008 R2. I one of it's 4 nic's set up and the rest are not being used. I have successfully given it an ip address, network mask, and dns servers. I can ping and resolve this machine from anywhere else in the network. However, when I try to connect to it via RDP it does several things: 1) it might just outright refuse me with the message, "This computer can't connect to the remote computer. Try connecting again." 2) it might connect me and let me chose the account I would like to log on as... but when you select an account then you receive the same message as in #1 3) it might actually allow you to connect but only for about 1 minute and then you receive the same message and it closes your session. I have configured the firewall service to allow for RDP over the domain network connection. This didn't have any noticible effect. I have now disabled the firewall for all 3 networks and have even stopped the Windows Firewall service. I am still having the same issue. I am new to Server 2008 R2 and things are very different. Please give me any advice you can on how to resolve this issue and/or any other gotchas that are sure to come my way. The 2003 - 2008 learning curve seems steep. Thanks

  Read the article

• Server 2012, Jumbo Frames - should I expect problems?

  - by TomTom

  Ok, this sound might stupid - but is there any negative on just enabling jumbo frames in practice? From what I understand: Any switch or ethernet adapter that sees a jumbo frame it can not handle will just drop it. TCP is not a problem as max frame size is negotiated in the setinuo phase. UCP is a theoretical problem as a server may just send a LARGE UDP packet that gets dropped on the way. Practically though, as UDP is packet based, I do not really think any software WOULD send a UDP packet larger than 1500 bytes net without app level configuration changes - at least this is how I do my programming, as it is quite hard to get a decent MTU size for that without testing yourself, so you fall back in programming to max 1500 packets. The network in question is a standard small business network - we upgraded now from a non managed 24 port switch to a 52 port switch with 4 10g ports (netgear - quite cheap) and will mov a file server to 10g for also ISCSI serving. All my equipment on the Ethernet level can handle minimum 9000 bytes and due to local firewalls I really want to get packets larger (less firewall processing), but the network is also NAT'ed to the internet. On top, different machines move around (download) large files (multi gigabyte area) quite often for processing. The question is - can I expect problems when I just enable jumbo frames? Again, this is not totally ignorance - I just don't see programs sending more than 1500 byte UDP packets (if that is a practical problem please tell me) and for TCP the MTU is negotiated anyway. if there is a problem I can move to a dedicated VLAN, but this has it's own shares of problems as basically most workstations must then be on both VLAN's.

  Read the article

• Firefox not using Kerberos despite being configured to

  - by Nicolas Raoul

  I am deploying Linux/Firefox on a corporate Kerberos network. I followed this Kerberos-on-Firefox procedure but still Firefox does not connect via the company's Kerberos. I am using Firefox 3.0.18 on RedHat EL Server 5.5 Here is what I did: Run kinit on the command line to create a Kerberos ticket Check with klist: the ticket is valid until tomorrow, service principal is krbtgt/[email protected]. In Firefox, set network.negotiate-auth.trusted-uris and network.negotiate-auth.delegation-uris to .dc.thecompany.com. Load the company's portal page via its full hostname: http://server37.thecompany.com/alfresco. (note: server37 is actually the machine I am running Firefox on, but that should not be a problem I guess) PROBLEM: the company's intranet portal still serves me the login/password page. The same portal correctly uses Kerberos on Internet Explorer/Windows 7 machines, same settings, and shows the user's personal page. The server does not see any Kerberos request coming. Did I do something wrong? I enabled NSPR_LOG_MODULES=negotiateauth:5 as explained here, but the log file stays empty.

  Read the article

• Rhythmbox - put a playlist on my iPod

  - by GorillaSandwich

  I have an old iPod nano and currently use iTunes in Windows to management. However, I'm trying to switch to Ubuntu. So far, iPod management is one major holdup. Besides being unable to easily manage podcasts, I also don't see a way to create a playlist and put it on my iPod. I can create a playlist on the computer in Rhythmbox, but I can't drag and drop it onto the iPod. I can create a playlist on the iPod itself, put I can't drag and drop songs from my library into it. If I right-click the songs, I can add them to playlists on the computer, but not on the iPod. How can I create a playlist of music in Rhythmbox and sync it to my iPod?

  Read the article

• When a python process is killed on OSX, why doesn't it kill the child processes?

  - by Hugh

  I found myself getting very confused a while back by some changes that I found when moving Python scripts from Linux over to OSX... On Linux, if a python script has called os.system(), and the calling process is killed, the called process will be killed at the same time. On OSX, however, if the main process is killed, anything that it launched is left behind. Is there something somewhere in OSX/Python where I can change this behaviour? This is causing problems on our render farm, where the processes can be killed from the management GUI, but the top level process is really just a wrapper, so, while the render farm management might think that the process has gone and the machine is freed up for another task, the actual processor-intensive task is still running, which can lead to huge blockages. I know that I could write more logic to catch the kill signal and pass it on to the child processes, but I was hoping that it might be something that could be enabled at a lower level.

  Read the article

• trying to figure out how to bridge two virtual networks together and in turn bridge that to the internet for a virtual inline IDS/IPS system

  - by Tony robinson

  I'm trying to figure out how to bridge two vmware (server or workstation, workstation) or virtualbox networks together with a linux IDS/IPS system transparently inline between both the virtual networks. How do I accomplish this? I understand how to bridge to virtual networks together, but how to I make the linux virtual machine sit between them and force traffic to go across the transparent bridge? I would like to have something along the lines of: vmnet a various vms host-only network ---- inline linux box vmnet a boxes forced to go through here to get to the internet --- vmnet b network with internet access configured as either NAT or bridged -- internet I know that basically the linux box needs two virtual nics, one on vmnet a and vmnet b, but other than that, I don't know how to force all the traffic to go across the "transparent" bridging linux box on its way to the internet. Do vmnet a and b have to be the same ip network with the same default route? does vmnet a not have a default route and vmnet b have a default route? I've read in vmware forums that on the linux host you need to change permissions on the vmnet files for promiscuous mode? is this true? how do you configure this scenario on a windows box?

  Read the article

• Restricting Access to Application(s) on Point of Sale system

  - by BSchlinker

  I have a customer with two point of sale systems, a few workstations and a Windows 2003 SBS Server. The point of sale systems are typically running QuickBooks Point of Sale and are logged in with a user who has restricted permissions / access (via Group Policy). Occasionally, one of the managers needs to be able to run a few additional applications -- including some accounting software. I have created an additional user for this manager, allowing them to login and access the accounting software. The problem is, it can be problematic to switch users on the system, as QuickBooks takes a few minutes to close (on POSUser) and then reopen (on ManagerUser). If customers are waiting, this slows things down drastically. Since the accounting software is stored on a network drive, it would be easiest if the manager could simply double click something, authenticate against the network drive / domain controller and then the program would launch. When they close the program, the session to the network drive would be lost and the program would no longer be accessible. Is there any easy way to do this? Both users are on a domain and the system is Windows 7. I just don't want to require the user to switch back and forth. In a worst case scenario, they forget to switch back and leave the accounting software wide open.

  Read the article

< Previous Page | 492 493 494 495 496 497 498 499 500 501 502 503  | Next Page >