Search Results

Search found 316 results on 13 pages for 'brandon shutter'.

Page 5/13 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • All internet requests in Windows time out

    - by Brandon
    So, I've run into a very strange problem with my home wireless network. Previously, at seemingly random times, the router seemed to disconnect all wireless hosts and cause all of the wired hosts to have a "limited connection" according to windows. In order to fix this, I had to unplug all of the wired hosts from the router, unplug the modem from the router, and power cycle the router. This seemed to solve the problem for a while until the exact same thing happened a day later and I had to go through the same process again. That's where I noticed something weird happening. There was one wireless host (a Windows Vista laptop) that seemed to be causing the router to disconnect the other hosts whenever it connected. When this happened, only that laptop was able to use the wireless from the router. When this happened, I disconnected it from the wireless (by disabling the wireless adapter) then reconnected it (by re-enabling it) and now it, like the other hosts, couldn't connect. I've never really seen anything this strange happen on our network before. So, I restored the router to factory settings and the problem seems to have vanished except one crucial problem. There's another host (a Windows 7 laptop) that was perfectly able to connect before all of the router issues and even in between the crashing and power-cycling events but now says its connected and says it's able to reach the Internet, but all requests time out. In any browser I've tried, the tab says connecting to [site]... for a solid minute and then tells me the request timed out. When I try to ping google.com in cmd it also says request timed out. In frustration, I booted into a dual-boot Ubuntu installation on the Windows 7 host and the connection works fine, to my surprise, as ubuntu is where I am now typing this rather long question. I haven't looked through the event log in windows but will post anything I find in an edit I haven't tried connecting (in Windows 7) to any other wireless network, since The fact that it works in Ubuntu suggests its Windows and not the router but I didn't change any wireless settings in windows before it being able to reach the Internet and not. Does anyone have any clue what could have happened. I opened to buying another router as this one is almost a year old :) but I would like to know whats going on here. Thanks in Advance! P.S. Sorry for how long my question is, I'm a little anxious (:

    Read the article

  • Allow SFTP to a single folder not in home directory

    - by Brandon
    I have a web server that I use to host my websites. I have all the websites in folders in /srv/www. There is a Wordpress site that I want to give SFTP access to another developer, how would I go about doing this so that they only have access to /srv/www/thesite.com and not any other directories? Running Ubuntu 9.04.

    Read the article

  • External component has thrown an exception. ASP.NET ASPX PAGE POST

    - by Brandon
    I have an aspx page that communicates with a webservice I have. It connects to an SQL Server database on my virtual dedicated server. With just a little usage, I get this error External component has thrown an exception. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Runtime.InteropServices.SEHException: External component has thrown an exception. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [SEHException (0x80004005): External component has thrown an exception.] Luxand.FSDK.Initialize(String DataFilesPath) +0 WebService.onLoad() +70 WebService..ctor() +91 facematch.btn_submit_Click(Object sender, EventArgs e) +218 System.Web.UI.WebControls.Button.OnClick(EventArgs e) +105 System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) +107 System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent(String eventArgument) +7 System.Web.UI.Page.RaisePostBackEvent(IPostBackEventHandler sourceControl, String eventArgument) +11 System.Web.UI.Page.RaisePostBackEvent(NameValueCollection postData) +33 System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +1746

    Read the article

  • Any way I can correct DNS spoofing against our domain

    - by brandon
    This morning I found out that our domain and subdomains have been poisoned on the 4.2.2 and 4.2.2.1 DNS servers along with others I think, though I have not confirmed others yet. Using OpenDNS resolution works correctly. I have updated our local DNS servers and cleared their cache which has fixed things internally. The issue is that the domain is public facing and customers are having problems. We are the authoritative DNS server for the domain and all that is under our control. What I don't know how to do is fix the name servers out of our control. Is there something we can do on our end? At the moment the only workaround I can think of is to ask customers to change their DNS to OpenDNS which is not very practical. The other workaround would be to change our TLD, which is less practical.

    Read the article

  • Terminal Server Install -- Add/Remove Program Message on NonAdministrator Machines

    - by Brandon
    First time poster... My company uses terminal services for one of our remote offices. Data is kept on a different server. OS is Windows Server 2003. Last week, they needed to purchase a program and have it installed on terminal server, which was done. An administrator session was started, the TS was put into install mode and the program was installed. The TS was then put back into execute mode. The install did not require a reboot. Since then, when any user who does not have administrator privileges initiates a remote session and logs in they get a security message that says "Add / Remove programs has been restricted. Please contact your system administrator." The only option is to click OK, which everyone does and after that there are no issues. Anyone have any idea why this is happening and how to fix? Thanks!

    Read the article

  • Sharepoint 2010 moving site collection to different database error

    - by Brandon Ulasiewicz
    I am trying to move a site collection from one content database to another content database. First I used the following PowerShell command: New-SPContentDatabase -Name New_DB -WebApplication http://portal/ I confirmed that this did in fact create the DB in the SQL Server. I then used the following command: Move-SPSite http://portal/sites/hr -DestinationDatabase New_DB This generates an error stating that the "Operation is not valid due to the current state of the object" Can anyone help point me in the right direction with this? Thanks

    Read the article

  • Project Server 2010 site creation - the database connection string is not available

    - by Brandon Montgomery
    I am trying to get Project Server 2010 up and running on a Win Server 2008 box. I've got Sharepoint 2010 installed and Project Server 2010 installed. I open SharePoint Central Administration, then I go to Manage Service Applications Project Server Service Application. It looks like there is a site under the "Sharepoint - 80" section, but the Status says "Failed - see the Application event Log". When I click on the site and select "Retry" I get the same thing. In the event viewer, I see an error with SharePoint Foundation Search as the Source - it reads: Could not create a database session. Context: Application '276504a6-93b1-4c1f-a900-fd6ed9d5c117' Details: The database connection string is not available. (0xc0041228) How can I fix this? Is there some configuration I missed?

    Read the article

  • just another apache to nginx rewrite question

    - by Brandon
    I have the following Apache rewrite directives: RewriteCond %{REQUEST_URI} ^/proxy(/|$) [NC] RewriteCond %{QUERY_STRING} (^|&)uri=(.*?)(&|$) [NC] RewriteRule .* /api/vs1.0/%2 [NC,L] And I'm trying out nginx, so trying to move the rewrites over. I came up with... rewrite ^/proxy(/|$) /api/vs1.0/$2 last; rewrite (^|&)uri=(.*?)(&|$) /api/vs1.0/$2 last; Which is probably grossly incorrect. I'm just a mere web developer, so I was wondering if anyone could lend a hand here. I would be much obliged. I see that I am ignoring the query string specification, but I'm thinking that it shouldn't matter. I only have a vague idea of what the original rewrite is accomplishing, so I haven't much hope here in coming up with something decent, despite reading the relevant documentation for both servers.

    Read the article

  • Cannot get Virtual PC to install on my machine

    - by Brandon
    I'm not sure what I'm doing wrong. I ran the tool to check that hardware virtualization is enabled, and it is (i7-2600). I ran the proper version of the Virtual PC download (Windows 7 Professional x64) and I can see the Windows Virtual PC (KB958559) update in my installed updates list. The .msu file runs fine without errors, but even after multiple reboots I can't actually find a trace of Virtual PC anywhere. There is nothing in program files, the start menu, or system32. Am I missing a step?

    Read the article

  • How to make mounted external drive writable over SFTP

    - by Brandon
    I have a user that I log in with over SFTP to my Ubuntu box. They have permission to write to the home directory of course. The external hard drive gets mounted to /media folder but I can't write to it over SFTP while logged in with that user. How would I set the permissions to allow me to write to the drive?

    Read the article

  • Need help creating a batch file to replace "." with "-"

    - by Brandon Ogle
    Like the title says, I need help creating a batch file to replace "." with "-", however I need to perserve the file extensions and it needs to work through the subfolders. I found another post on here that got the effect I wanted but it also swapped the . in my file extensions. I am a completely ignorant regarding shell script so please be detailed in your response. I have no idea what any of the switches mean or even how to specify the path for that matter. Thanks!

    Read the article

  • Why does Resource Monitor in windows 7 show half my memory as "Hardware Reserved"?

    - by Brandon
    Does anyone know why in Windows 7 Resource Monitor shows that I have 8 GB of RAM installed on my computer, but I only have 3.2 GB available as 4.8 GB are in "Hardware Reserve". I researched this issue and tried going into msconfig and making sure that in the boot options the number of processors and max memory options were turned off. I also opened the computer up and reseated each of the memory sticks while clearing out any dust that was in there. Some info on the system I am using: OS: Windows 7 Enterprise 64-bit Edition CPU: AMD Phenom X4 9750 Memory: 4 X 2GB DDR2 memory Motherboard: MS-7548 (Aspen) Any help would be much appreciated.

    Read the article

  • htacces rewrite condition old site to new site with querystring

    - by Brandon Braner
    I am not even going to pretend to fully understand how htaccess rewrite conidtions work. Ive been working on this for a while searching and searching. I have an old wordpress site www.old-site.com and a new site www.site.com wordpress uses query strings page_id=# to redirect to pages on the old site page_id=2 went to a specific page but on the new site it goes the the home page i need old-site/?page_id=2 to go to site.com/our-company here is what i am trying RewriteCond %{HTTP_HOST} ^(www.)?old-site.com$ [NC] RewriteCond %{QUERY_STRING} ^page_id=2$ RewriteRule ^(.*)$ http://www.site.com/our-company/ [R=301,L] if i take out the rewrite conditio for query string it redirects all traffic from old-site.com to the our company page on the new site. where am i going wrong? i have about 15 redirects i need to do this way. thanks in advance

    Read the article

  • Group Policy dealing with IE zone assignment not sticking!

    - by Brandon
    I have a group policy (which ONLY deals with the zone assignment) -that is continually switching on and off with reboots. I thought it was a conflicting group policy but when I run group policy modeling report it doesn't show any descrepancies that I can see. I thought it may be an issue with one domain controller wasn't replicating my policy change to the other one, but this isn't the case. I checked both domain controllers and they show the same information. The assignment is on a user basis and is in: user configuration > administrative templates > windows components > internet explorer > internet control panel > security and is site to zone assignment.

    Read the article

  • Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

    - by Brandon Bearden
    Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

    Read the article

  • htaccess rewrite condition old site to new site with querystring

    - by Brandon Braner
    I am not even going to pretend to fully understand how htaccess rewrite conditions work. I've been working on this for a while searching and searching. I have an old Wordpress site www.old-site.com and a new site www.site.com. Wordpress uses query strings page_id=# to redirect to pages. On the old site page_id=2 went to a specific page but on the new site it goes the the home page. I need old-site/?page_id=2 to go to site.com/our-company Here is what I am trying RewriteCond %{HTTP_HOST} ^(www\.)?old-site.com$ [NC] RewriteCond %{QUERY_STRING} ^page_id=2$ RewriteRule ^(.*)$ http://www.site.com/our-company/ [R=301,L] If I take out the rewrite condition for query string it redirects all traffic from old-site.com to the company page on the new site. Where am I going wrong? I have about 15 redirects I need to do this way.

    Read the article

  • Windows 2008 Best Raid Configuration

    - by Brandon Wilson
    I have 4 2TB hard drives and I was thinking about using Raid 10. This would give me 4TB correct? My next question is would it be easy to add more hard drives to the raid array. For example if I bought another hard drive can I add it to the array without backing up any data? Basically I want to be able to start off with 4TB and when the space becomes full add more space as needed. If this isn't possible with Raid 10, is it possible with any Raid configuration. Any suggestions would be appreciated. Thank you.

    Read the article

  • Synergy: How to screen positioning configuration while it is running?

    - by Brandon
    I am using Synergy between two Macbooks (10.6 & 10.7). Installed using homebrew, version '1.3.6p2' from I will sit in various places in relation to the secondary laptop, so sometimes I want the other screen to be on the right of my main screen and sometimes to the left. How can I reconfigure this without shutting down synergys, changing the config file, and restarting the server and the client? Ideally it will be a terminal command so I can easily assign it to a keyboard shortcut. Thanks!

    Read the article

  • How do I change the .NET Framework version of a virtual directory without the ASP.NET tab?

    - by Brandon
    I have a website running v2.0 but I want the virtual directory running under it to use v4.0. I've already set the virtual directory as an application and gave it it's own application pool. The server is running Windows Server 2003 SP2 (64-bit). However it has the Enable32BitAppOnWin64 flag enabled which means the ASP.NET tabs on the properties dialog of the websites/virtual directories are missing. .NET 4.0 is installed, aspnet_regiis -lv lists the 32-bit and 64-bit versions of .NET 2.0 and .NET 4.0 and the Web Server Extensions are enabled. I can't disable the Enable32BitAppOnWin64 flag to get the ASP.NET tab back, so is there a way to do this from the command line without potentially breaking something? I ran aspnet_regiis -lk to find the paths so I could try aspnet_regiis -sn, but it only returns one record W3SVC/ 2.0.50727.0 (There are 3 separate websites and a virtual directory running on the server though) How can I change the framework version of the virtual directory without the ASP.NET tab?

    Read the article

  • Server Design Enquiry [closed]

    - by Brandon Gelfand
    I am really new to this and am having trouble with how I can store information from a website. I am going to be making a site similar to dropbox for my company and there is gonna be around 40 TB of space that we need to be able to access on the go, for instance pull the file up on the phone or off our laptop using the internet. Obviously using an Amazon S3 server is not the most cost effective way of doing this so how can I make my own server to hold all of the info and communicate to it from a website? Please I need as much help as possible, like a blueprint or something. Thanks and sorry for the noobish question but I can't really find an exact answer to my question.

    Read the article

  • Silverlight Cream for March 24, 2010 -- #819

    - by Dave Campbell
    In this Issue: Nokola, Tim Heuer, Christian Schormann, Brad Abrams, David Kelley, Phil Middlemiss, Michael Klucher, Brandon Watson, Kunal Chowdhury, Jacek Ciereszko, and Unni. Shoutouts: Michael Klucher has a short post up For Love of the Game (Development)…, where he's looking for some input from the developer community. Shawn Hargreaves has a link post up of all the Windows Phone MIX10 presentations Chris Cavanagh has a Soft-Body Physics for Windows Phone 7 post up that goes along with one he did 1-1/2 years ago! Jeff Weber posted An Open Letter To Microsoft Regarding The Silverlight Game Development Community Pete Brown posted his MIX10 Recap ... lots of information, and discussion of what he was up to ... I liked the Trivia app Pete... glad to hear that was yours :) I've changed my mind and added a WP7 tag to SilverlightCream. I'll straighten out all the Mobile plus Silverlight links to point at the WP7 tab hopefully tonight. From SilverlightCream.com: EasyPainter Source Pack 3: Adorners, Mouse Cursors and Frames Nokola has been busy with EasyPainter adding in Custom, Extensible Mouse Cursors and Customizable Adorners with extensible adorner frames, and best of all... all with source code! Simulate Geo Location in Silverlight Windows Phone 7 emulator Among the things we don't have in our WP7 emulators is Geo Location... Tim Heuer comes to the rescue with a simulator for it... too cool, Tim! Blend 4: About Path Layout, Part II Christian Schormann is back with Part 2 of his tutorial sequence on the new Path Layout. Really good info and definitely cool presentations of the control. Silverlight 4 + RIA Services - Ready for Business: Exposing OData Services Brad Abrams continues his series with a post on exposing OData services. This looks like a great tutorial on the topic... will probably resolve some questions I've been having :) No Silverlight and Preloader Experience(ish) - in 10 seconds... David Kelley exposes the code he uses on his site, designed to be friendly to Silverlight and non-Silverlight users alike. Merged Dictionaries of Style Resources and Blend Phil Middlemiss has a nice article up on Merged Dictionaries and using multiple resource dictionaries that the app chooses, but also be compatible with Prism and Blend while not eating your system resources out of house and home. XNA Game Studio and Windows Phone Emulator Compatibility Michael Klucher has a definitive post up about getting your XNA and system up-to-speed for WP7... a must-read if you've been running any of the other XNA drops. Windows Phone 7 301 Redirect Bug Brandon Watson reports a 301 Redirect bug on WP7 ... see the code and how he got it, then follow along as he explains all the debug paths he took and what the resolution (?) really is :) Silverlight 4: How to use the new Printing API? Kunal Chowdhury has a tutorial up on printing with Silverlight 4 RC... from the project layout to printing and then printing a smaller section... all good Printing problem in Silverlight 4.0 RC - loading images in code behind Jacek Ciereszko also is writing about printing, and in his case he had problems with loading an image dynamically and printing it... plus he provides a solution to the 'blank page' problem. ToolboxExampleAttribute - a new extension point in Blend 4 (and a few other extensibility related changes) Unni has an article up about Expression Blend 4's new ToolboxExampleAttribute which allow you to have multiple examples of the same type resulting in different XAML produced. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone    MIX10

    Read the article

  • Twitter Typeahead only shows only 5 results

    - by user3685388
    I'm using the Twitter Typeahead version 0.10.2 autocomplete but I'm only receiving 5 results from my JSON result set. I can have 20 or more results but only 5 are shown. What am I doing wrong? var engine = new Bloodhound({ name: "blackboard-names", prefetch: { url: "../CFC/Login.cfc?method=Search&returnformat=json&term=%QUERY", ajax: { contentType: "json", cache: false } }, remote: { url: "../CFC/Login.cfc?method=Search&returnformat=json&term=%QUERY", ajax: { contentType: "json", cache: false }, }, datumTokenizer: Bloodhound.tokenizers.obj.whitespace('value'), queryTokenizer: Bloodhound.tokenizers.whitespace }); var promise = engine.initialize(); promise .done(function() { console.log("done"); }) .fail(function() { console.log("fail"); }); $("#Impersonate").typeahead({ minLength: 2, highlight: true}, { name: "blackboard-names", displayKey: 'value', source: engine.ttAdapter() }).bind("typeahead:selected", function(obj, datum, name) { console.log(obj, datum, name); alert(datum.id); }); Data: [ { "id": "1", "value": "Adams, Abigail", "tokens": [ "Adams", "A", "Ad", "Ada", "Abigail", "A", "Ab", "Abi" ] }, { "id": "2", "value": "Adams, Alan", "tokens": [ "Adams", "A", "Ad", "Ada", "Alan", "A", "Al", "Ala" ] }, { "id": "3", "value": "Adams, Alison", "tokens": [ "Adams", "A", "Ad", "Ada", "Alison", "A", "Al", "Ali" ] }, { "id": "4", "value": "Adams, Amber", "tokens": [ "Adams", "A", "Ad", "Ada", "Amber", "A", "Am", "Amb" ] }, { "id": "5", "value": "Adams, Amelia", "tokens": [ "Adams", "A", "Ad", "Ada", "Amelia", "A", "Am", "Ame" ] }, { "id": "6", "value": "Adams, Arik", "tokens": [ "Adams", "A", "Ad", "Ada", "Arik", "A", "Ar", "Ari" ] }, { "id": "7", "value": "Adams, Ashele", "tokens": [ "Adams", "A", "Ad", "Ada", "Ashele", "A", "As", "Ash" ] }, { "id": "8", "value": "Adams, Brady", "tokens": [ "Adams", "A", "Ad", "Ada", "Brady", "B", "Br", "Bra" ] }, { "id": "9", "value": "Adams, Brandon", "tokens": [ "Adams", "A", "Ad", "Ada", "Brandon", "B", "Br", "Bra" ] } ]

    Read the article

  • Unable to set TestContext property

    - by Brandon
    I have a visual studio 2008 Unit test and I'm getting the following runtime error: Unable to set TestContext property for the class JMPS.PlannerSuite.DataServices.MyUnitTest. Error: System.ArgumentException: Object of type 'Microsoft.VisualStudio.TestTools.TestTypes.Unit.UnitTestAdapterContext' cannot be converted to type 'Microsoft.VisualStudio.TestTools.UnitTesting.TestContext' I have read that VS 2008 does not properly update the references to the UnitTestFramework when converting 2005 projects. My unit test was created in 2008 but it inherits from a base class built in VS 2005. Is this where my problem is coming from? Does my base class have to be rebuilt in 2008? I would rather not do this as it will affect other projects. In other derived unit tests built in 2005, all that we needed to do was comment out the TestContext property in the derived unit test. I have tried this in the VS 2008 unit test with no luck. I have also tried to "new" the TestContext property which gives me a different runtime error. Any ideas?

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >