Search Results

Search found 130 results on 6 pages for 'cheese'.

Page 5/6 | < Previous Page | 1 2 3 4 5 6  | Next Page >

  • Using multiple USB webcams in Linux

    - by rachelderp
    Running more than one USB webcam in Debian/Linux results in the the following error: libv4l2: error turning on stream: No space left on device VIDIOC_STREAMON: No space left on device What initially seemed to be a programming issue in OpenCV turned into a quest for a mysterious hardware/software problem after the same errors were produced by running cheese and xawtv. Apparently it's caused by webcams requesting all the available bandwidth on the USB host controller. With that in mind I decided to run wireshark and capinfos to see just how much bandwidth a single camera used. 4 megabits per second at 320x240 14 megabits per second at 640x480 32 megabits per second at 1920x1080 Interesting! That might explain why two cameras at 320x240 work but any higher resolution fails. It's as if my USB controller is only operating at USB 1 speeds, yet lsusb shows both webcams belonging to a device which supposedly supports 480 megabits per second. One solution proposed forcing the webcams to calculate their bandwidth usage instead of requesting their maximum by running the following commands: sudo rmmod uvcvideo sudo modprobe uvcvideo quirks=128 Unfortunately that made no difference, so I decided to try another solution. A post on StackOverflow suggested telling my webcams to use a lower FPS or compressed video format like MJPEG, but after running v4lctl list it doesn't appear either of my webcams support changing their video mode. And that's where I'm stuck. Why would two webcams operating well below the maximum speed of USB 2 would produce this error? ps: It's not a disk space issue, df displays no change when the webcams are started. pps: If it makes a difference, here's the output of lsusb

    Read the article

  • Grouping data in LINQ with the help of group keyword

    - by vik20000in
    While working with any kind of advanced query grouping is a very important factor. Grouping helps in executing special function like sum, max average etc to be performed on certain groups of data inside the date result set. Grouping is done with the help of the Group method. Below is an example of the basic group functionality.     int[] numbers = { 5, 4, 1, 3, 9, 8, 6, 7, 2, 0 };         var numberGroups =         from num in numbers         group num by num % 5 into numGroup         select new { Remainder = numGroup.Key, Numbers = numGroup };  In the above example we have grouped the values based on the reminder left over when divided by 5. First we are grouping the values based on the reminder when divided by 5 into the numgroup variable.  numGroup.Key gives the value of the key on which the grouping has been applied. And the numGroup itself contains all the records that are contained in that group. Below is another example to explain the same. string[] words = { "blueberry", "abacus", "banana", "apple", "cheese" };         var wordGroups =         from num in words         group num by num[0] into grp         select new { FirstLetter = grp.Key, Words = grp }; In the above example we are grouping the value with the first character of the string (num[0]). Just like the order operator the group by clause also allows us to write our own logic for the Equal comparison (That means we can group Item by ignoring case also by writing out own implementation). For this we need to pass an object that implements the IEqualityComparer<string> interface. Below is an example. public class AnagramEqualityComparer : IEqualityComparer<string> {     public bool Equals(string x, string y) {         return getCanonicalString(x) == getCanonicalString(y);     }      public int GetHashCode(string obj) {         return getCanonicalString(obj).GetHashCode();     }         private string getCanonicalString(string word) {         char[] wordChars = word.ToCharArray();         Array.Sort<char>(wordChars);         return new string(wordChars);     } }  string[] anagrams = {"from   ", " salt", " earn", "  last   ", " near "}; var orderGroups = anagrams.GroupBy(w => w.Trim(), new AnagramEqualityComparer()); Vikram  

    Read the article

  • December 3 is Stephanie Choyer Day

    - by rickramsey
    I don't answer Stephanie Choyer's email just so I can enjoy her French accent when she calls. "Reek! Reek! Why do joo not answer my eemails?" Without the French, life on Earth would be so much poorer. No, they don't bring to the party any motorcycles that grow chest on your hair, and the Citroen is such a frightening study in Automobile design that I don't dare climb inside one. But they have French architecture. French sidewalks. French villages. The French Alps. Grenoble. French cheese. French wine. And that glorious French accent. If I were French, I'd spend all my time enjoying being French. Which makes the work that Stephanie does day in and day with our hard-edged technologies and stubborn technologists so admirable. Oracle Solaris 11 Resources for Sysadmins and Developers The page in the link above represents the work of many people, but it was Steph who rounded them up. And it wasn't easy. I know, because I ran and hid from her on many, many occasions. But she was tireless. "Reek. Reek. Why have you not published Glynn's article? Pleeeease, you must!" Remember when tech companies gave you a simple choice? You could either read the 27,000 pages of documentation or a double-sided data sheet. Which will it be, pal? Then they started writing white papers. 74 pages of excellent prose did a beautiful job of explaining why the technology was fantastic, but never told you how to use it. Well, have you taken a look at these? How-To Technical Articles for System Admins and Developers Now you can get wicked excited about a cool technique described in a 74-page white paper, and find a technical article that shows you exactly how to use it. The wicked smart marketing folks on the Oracle Solaris team wrote them, but it was Steph who bribed them with a Cabernet or beat them over the head with a baguette until all that work was finished and posted on OTN. There are songs about French wine, but not about French vintners. There are songs about French cities, but not about French bricklayers. About French sidewalks, but not about the French policemen who keep them safe. As far as I know, there are no songs about OTN, but if there were, they would probably neglect to mention Steph. Which is why today, Dec 3rd, we celebrate Stephanie Choyer Day. We dedicate this day to our relentless, hardworking, tireless, patient and friendly French colleague with the delightful accent. If I knew how to speak French, I'd say "Thanks for all you do" in French. But I don't speak French. And I don't trust online translations. I'd probably wind up saying "My left foot yearns for curdled milk." So here it is in plain old English: Thank you, Stephanie. psssst! about that documentation and those white papers ... In case you haven't noticed, the Oracle Solaris doc team has done some pretty cool things with the Solaris docs. And those white papers are interesting reading, well worth setting aside some time. Because with Solaris, as you know, it's not just about getting by with a rudimentary grasp of the basics. It's about the amazing stuff savvy sysadmins and developers can do when they really understand it. Find them here: White Papers Documentation And don't forget training! - Rick Website Newsletter Facebook Twitter

    Read the article

  • Integrated webcam in lenovo t410 not working with 12.04

    - by kristianp
    I have a Lenovo T410 with an inbuilt webcam and I haven't been able to get the webcam working. I tried skype, cheese, both just give me a black window. The microphone works fine with skype, by the way. Can anyone provide any clues please? The webcam is enabled in the bios, but there is no light indicating the webcam is on (not sure if there should be, though). I tried this on Kubuntu 11.10 and have upgraded to 12.04 with the same results. The Fn-F6 keyboard combination doens't seem to do anything either. EDIT: I got the webcam replaced, it looks like it was a hardware problem, because it works fine now. Thanks guys. $ ls /dev/v4l/* /dev/v4l/by-id: usb-Chicony_Electronics_Co.__Ltd._Integrated_Camera-video-index0 /dev/v4l/by-path: pci-0000:00:1a.0-usb-0:1.6:1.0-video-index0 And lsusb: $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 004: ID 0a5c:217f Broadcom Corp. Bluetooth Controller Bus 001 Device 005: ID 17ef:480f Lenovo Integrated Webcam [R5U877] Bus 002 Device 003: ID 05c6:9204 Qualcomm, Inc. Bus 002 Device 004: ID 17ef:1003 Lenovo Integrated Smart Card Reader Here is the output from guvcview, minus lots of lines describing the available capture formats. It says "unable to start with minimum setup. Please reconnect your camera.". guvcview 1.5.3 ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, .... { discrete: width = 1600, height = 1200 } Time interval between frame: 1/15, vid:17ef pid:480f driver:uvcvideo checking format: 1196444237 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! Init video returned -2 trying minimum setup ... video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } .... vid:17ef pid:480f driver:uvcvideo checking format: 1448695129 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! ERROR: Minimum Setup Failed. Exiting... VIDIOC_REQBUFS - Failed to delete buffers: Invalid argument (errno 22) cleaned allocations - 100% Closing portaudio ...OK Terminated.

    Read the article

  • How do I use ffmpeg to take pictures with my web camera?

    - by user45583
    I want to use ffmpeg to store images taken by my USB web camera on my Ubuntu 11.10. lsusb outputs: Bus 002 Device 003: ID 0c45:6028 Microdia Typhoon Easycam USB 330K (older) The camera works fine using cheese but I want to use command line tools to make it scriptable but if I try: ffmpeg -i /dev/v4l/by-id/usb-0c45_USB_camera-video-index0 image.jpg The output is: user@box:~$ sudo ffmpeg -i /dev/v4l/by-id/usb-0c45_USB_camera-video-index0 image.jpg [sudo] password for user: ffmpeg version 0.7.3-4:0.7.3-0ubuntu0.11.10.1, Copyright (c) 2000-2011 the Libav developers built on Jan 4 2012 16:21:50 with gcc 4.6.1 configuration: --extra-version='4:0.7.3-0ubuntu0.11.10.1' --arch=i386 --prefix=/usr --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --enable-libvpx --enable-runtime-cpudetect --enable-vaapi --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static WARNING: library configuration mismatch avutil configuration: --extra-version='4:0.7.3-0ubuntu0.11.10.1' --arch=i386 --prefix=/usr --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --enable-libvpx --enable-runtime-cpudetect --enable-vaapi --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --shlibdir=/usr/lib/i686/cmov --cpu=i686 --enable-shared --disable-static --disable-ffmpeg --disable-ffplay avcodec configuration: --extra-version='4:0.7.3-0ubuntu0.11.10.1' --arch=i386 --prefix=/usr --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --enable-libvpx --enable-runtime-cpudetect --enable-vaapi --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --shlibdir=/usr/lib/i686/cmov --cpu=i686 --enable-shared --disable-static --disable-ffmpeg --disable-ffplay avformat configuration: --extra-version='4:0.7.3-0ubuntu0.11.10.1' --arch=i386 --prefix=/usr --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --enable-libvpx --enable-runtime-cpudetect --enable-vaapi --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --shlibdir=/usr/lib/i686/cmov --cpu=i686 --enable-shared --disable-static --disable-ffmpeg --disable-ffplay avdevice configuration: --extra-version='4:0.7.3-0ubuntu0.11.10.1' --arch=i386 --prefix=/usr --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --enable-libvpx --enable-runtime-cpudetect --enable-vaapi --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --shlibdir=/usr/lib/i686/cmov --cpu=i686 --enable-shared --disable-static --disable-ffmpeg --disable-ffplay avfilter configuration: --extra-version='4:0.7.3-0ubuntu0.11.10.1' --arch=i386 --prefix=/usr --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --enable-libvpx --enable-runtime-cpudetect --enable-vaapi --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --shlibdir=/usr/lib/i686/cmov --cpu=i686 --enable-shared --disable-static --disable-ffmpeg --disable-ffplay swscale configuration: --extra-version='4:0.7.3-0ubuntu0.11.10.1' --arch=i386 --prefix=/usr --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --enable-libvpx --enable-runtime-cpudetect --enable-vaapi --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --shlibdir=/usr/lib/i686/cmov --cpu=i686 --enable-shared --disable-static --disable-ffmpeg --disable-ffplay postproc configuration: --extra-version='4:0.7.3-0ubuntu0.11.10.1' --arch=i386 --prefix=/usr --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --enable-libvpx --enable-runtime-cpudetect --enable-vaapi --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --shlibdir=/usr/lib/i686/cmov --cpu=i686 --enable-shared --disable-static --disable-ffmpeg --disable-ffplay libavutil 51. 7. 0 / 51. 7. 0 libavcodec 53. 6. 0 / 53. 6. 0 libavformat 53. 3. 0 / 53. 3. 0 libavdevice 53. 0. 0 / 53. 0. 0 libavfilter 2. 4. 0 / 2. 4. 0 libswscale 2. 0. 0 / 2. 0. 0 libpostproc 52. 0. 0 / 52. 0. 0 /dev/v4l/by-id/usb-0c45_USB_camera-video-index0: Invalid data found when processing input How do I make this work?

    Read the article

  • Apprentice Boot Camp in South Africa (Part 2)

    - by Tim Koekkoek
    By Maximilian Michel (DE), Jorge Garnacho (ES), Daniel Maull (UK), Adam Griffiths (UK), Guillermo De Las Nieves (ES), Catriona McGill (UK), Ed Dunlop (UK) Today we have the second part of the adventures of seven apprentices from all over Europe in South-Africa!  Kruger National Park & other experiences Going to the Kruger National Park was definitely an experience we will all remember for the rest of our lives. This trip,organised by Patrick Fitzgerald, owner of the Travellers Nest (where we all stayed), took us from the hustle and bustle of Joburg to experience what Africa is all about, the wild! Although the first week’s training we had prior to this trip to the Kruger was going very well, we all knew this was to be a very nice break before we started the second week of training. And we were right, the animals, scenery and sights we saw were just simply incredible and like I said something we will remember for the rest of our lives. To see lions, elephants, cheetahs and rhinos and many more in a zoo is one thing, but to see them in the wild, in their natural habitat is very special and I personally only realised this from the early 5 am start on the first morning in the Kruger, which was definitely worth it. Not only was it all about the safari, we ate some wonderful food, in particular on the Saturday night, Patrick made us a traditional South African Braai which was one of my favourite meals of the whole two weeks. After the Kruger National Park we had a whole day of traveling back to Johannesburg but even this was made to be a good day by our hosts. Despite the early start on the road it was all worth it by the time we reached God's Window. The walk to the top was made a lot harder by all the steaks we had eaten in the first week but the hard walk was worth it at the top, with views that stretched for miles. The Food The food in South Africa is typically meat and in big amounts, while there we ate a lot of big beef steaks, ribs and kudu sausage. All of the meat we ate was usually cooked with a sauce such as a Barbeque glaze. The restaurants we visited were: Upperdeck Restaurant, with live music and a great terrace to eat, the atmosphere was good for enjoying the music and eating our food. Most of us ate  Spare ribs that weighed 600 kg, with barbecue sauce that was delicious. Die Bosvelder Pub & Restaurant is a restaurant with a very surprising decor, this is because the walls had many of south Africa’s famous animals on them. The food was maybe the best we ate in South Africa. Our orders were: Springbokvlakte Lambs' Neck Stew, beef in gravy and steaks topped with cheese and then more meat on top! All meals were accompanied by a selection of white sauce cauliflower, spinach and zanhorias. Pepper Chair Restaurant, where the specialty is T-Bone steaks of 1.4 kg, but most of us were happy to attempt the 1 kg. Cooked with barbecue sauce over the meat, it was very good!  The only problem was their size causing the  the meat to get cold if you did not eat it very fast! We’re all waiting for our 1.0 kg t-bone steak including our Senior Director EMEA Systems Support Germany & Switzerland: Werner Hoellrigl The Godfather Restaurant, the food here was more meat in abundance. We ate: great ribs, hamburgers, steaks and all accompanied with a small plates of carrot and sauteed spinach, very good. We had two great weeks in South-Africa! If you want to join Oracle, then check http://campus.oracle.com 

    Read the article

  • Social Search: Looking for Love

    - by Mike Stiles
    For marketers and enterprise executives who have placed a higher priority on and allocated bigger budgets to search over social, it might be time to notice yet another shift that’s well underway. Social is search. Search marketing was always more of an internal slam-dunk than other digital initiatives. Even a C-suite that understood little about the new technology world knew it’s a good thing when people are able to find you. Google was the new Yellow Pages. Only with Google, you could get your listing first without naming yourself “AAAA Plumbing.” There were wizards out there who could give your business prominence in front of people who were specifically looking for what you offered. Other search giants like Bing also came along to offer such ideal matchmaking possibilities. But what if the consumer isn’t using a search engine to find what they’re looking for? And what if the search engines started altering their algorithms so that search placement manipulation was more difficult? Both of those things have started to happen. Experian Hitwise’s numbers show that visits to the major search engines in the UK dropped 100 million through August. Search engines are far from dead, or even challenged. But more and more, the public is discovering the sites and brands they need through advice they get via social, not search. You’ll find the worlds of social and search increasingly co-mingling as well. Search behemoths Google and Bing are including Facebook and Google+ into their engines. Meanwhile, Facebook and Twitter have done some integration of global web search into their platforms. So what makes social such a worthwhile search entity for brands? First and foremost, the consumer has demonstrated a behavior of acting on recommendations from social connections. A cry in the wilderness like, “Anybody know any good catering companies?” will usually yield a link (and an endorsement) from a friend such as “Yeah, check out Just-Cheese-Balls Catering.” There’s no such human-driven force/influence behind the big search engines. Facebook’s Mark Zuckerberg and others call it “Friend Mining.” It is, in essence, searching for answers from friends’ experiences as opposed to faceless code. And Facebook has all of those friends’ experiences already stored as data. eMarketer says search in an $18 billion business, and investors are really into it. So no shock Facebook’s ready to leverage their social graph into relevant search. What do you do about all this as a brand? For one thing, it’s going to lead to some interesting paid marketing opportunities around the corner, including Sponsored Stories bought against certain queries, inserting deals into search results, capitalizing on social search results on mobile, etc. Apart from that, it might be time to stop mentally separating social and search in your strategic planning and budgeting. Courting your fans on social will cumulatively add up to more valuable, personally endorsed recommendations for your company when a consumer conducts a search on social. Fail to foster those relationships, fail to engage, fail to provide knock-em-dead customer service, fail to wow them with your actual products and services…and you’ll wind up with the visibility you deserve in social search results.

    Read the article

  • Python dictionary formating

    - by None
    I made a python function to convert dictionaries to formatted strings. My goal was to have a function take a dictionary for input and turn it into a string that looked good. For example, something like "{'text':'Hello', 'blah':{'hi':'hello','hello':'hi'}}" would be turned into this: text: Hello blah: hi: hello hello: hi This is the code I wrote: indent = 0 def format_dict(d): global indent res = "" for key in d: res += (" " * indent) + key + ":\n" if not type(d[key]) == type({}): res += (" " * (indent + 1)) + d[key] + "\n" else: indent += 1 res += format_dict(d[key]) indent -= 1 return res #test print format_dict({'key with text content':'some text', 'key with dict content': {'cheese': 'text', 'item':{'Blah': 'Hello'}}}) It works like a charm. It checks if the dictionary item is another dictionary, in which it process that, or something else, in which it would use that as the value. The problem is: I can't have a dictionary and a string together in a dictionary item. For example: if I wanted blah: hi hello: hello again there'd be no way to do it. Is there some way I could have something like a list item in a dictionary. Something like this "{'blah':{'hi', 'hello':'hello again'}}"? And if you provide a solution could you tell me how I would need to change my code (if it did require changes). Note: I am using python 2.5

    Read the article

  • Clear form field after select for jQuery UI Autocomplete

    - by jonfhancock
    I'm developing a form, and using jQuery UI Autocomplete. When the user selects an option, I want the selection to pop into a span appended to the parent <p> tag. Then I want the field to clear rather than be populated with the selection. I have the span appearing just fine, but I can't get the field to clear. How do you cancel jQuery UI Autocomplete's default select action? Here is my code: var availableTags = ["cheese", "milk", "dairy", "meat", "vegetables", "fruit", "grains"]; $("[id^=item-tag-]").autocomplete({ source: availableTags, select: function(){ var newTag = $(this).val(); $(this).val(""); $(this).parent().append("<span>" + newTag + "<a href=\"#\">[x]</a> </span>"); } }); Simply doing $(this).val(""); doesn't work. What is maddening is that almost the exact function works fine if I ignore autocomplete, and just take action when the user types a comma as such: $('[id^=item-tag-]').keyup(function(e) { if(e.keyCode == 188) { var newTag = $(this).val().slice(0,-1); $(this).val(''); $(this).parent().append("<span>" + newTag + "<a href=\"#\">[x]</a> </span>"); } }); The real end result is to get autocomplete to work with multiple selections. If anybody has any suggestions for that, they would be welcome.

    Read the article

  • jQuery/Javascript: Click event on a checkbox and the 'checked' attribute.

    - by b. e. hollenbeck
    The code: $('input.media-checkbox').live('click', function(e){ e.preventDefault(); var that = $(this); if (that.attr('checked') == 'checked'){ var m = that.attr('media'); var mid = 'verify_' + m; that.parents('div.state-container').find('ul.' + mid).remove(); that.attr('checked', false); } else { var url = AJAX_URL; $.ajax({ type: 'GET', url: url, dataType: 'html', success: function(data){ that.parents('li').siblings('li.verification').children('div.media-verification').append(data).fadeIn(500); that.attr('checked', 'checked'); } }); } return false; }); I am ajaxing in a form, then firing the click event on relevant checkboxes to ajax in another partial if necessary. The form is inserted nicely, and the click events are fired, checking the boxes that need to be checked and firing the second ajax, since the checked attribute of the checkbox was initially false. What's curdling my cheese is if I UNCHECK one of those boxes. Despite e.preventDefault(), the checked attribute is set to false BEFORE the test, so the if statement always executes the else statement. I've also tried this with $.is(':checked'), so I'm completely baffled. It appears that unchecked - checked state reads the original state, but checked - unchecked doesn't. Any help?

    Read the article

  • How to get a handle to all JCheckBox objects in order to loop?

    - by EmmyS
    I'm very new to Java and am having some issues looping through JCheckBoxes on a UI. The idea is that I have a bunch of checkboxes (not in a group because more than one can be selected.) When I click a JButton, I want to build a string containing the text from each selected checkbox. The issue I'm having is that our instructor told us that the checkboxes need to be created via a method, which means (see code below) that there isn't a discrete instance name for each checkbox. If there were, I could say something like if(checkBox1.isSelected()) { myString.append(checkBox.getText()); } That would repeat for checkBox2, checkBox3, and so on. But the method provided to us for adding checkboxes to a panel looks like this: public class CheckBoxPanel extends JPanel { private static final long serialVersionUID = 1L; public CheckBoxPanel(String title, String... options) { setBorder(BorderFactory.createTitledBorder(BorderFactory .createEtchedBorder(), title)); setLayout(new BoxLayout(this, BoxLayout.Y_AXIS)); // make one checkbox for each option for (String option : options) { JCheckBox b = new JCheckBox(option); b.setActionCommand(option); add(b); } } } This is called like this: toppingPanel = new CheckBoxPanel("Each Topping $1.50", "Tomato", "Green Pepper", "Black Olives", "Mushrooms", "Extra Cheese", "Pepperoni", "Sausage"); So I now have a panel that contains a border with the title "Each Topping $1.50", and 7 visible checkboxes. What I need to do is get a list of all the selected toppings. We are not supposed to use an ActionListener for each checkbox, but rather get the list when a button is clicked. I'm feeling really clueless here, but I just can't figure out how to get the isSelected property of the checkboxes when the individual checkboxes don't have instance names. Ideally I'd like to somehow add all the checkboxes to an array and loop through the array in the button's action listener to determine which ones are checked, but if I have to check each one individually I will. I just can't figure out how to refer to an individual checkbox when they've been created dynamically.

    Read the article

  • How to make the value of one select box drive the options of a second select box

    - by Ben McCormack
    I want to make an HTML form with 2 select boxes. The selected option in the first select box should drive the options in the second select box. I would like to solve this dynamically on the client (using javascript or jQuery) rather than having to submit data to the server. For example, let's say I have the following Menu Categories and Menu Items: Sandwiches Turkey Ham Bacon Sides Mac 'n Cheese Mashed Potatoes Drinks Coca Cola Sprite Sweetwater 420 I would have two select boxes, named Menu Category and Items, respectively. When the user selects Sandwiches in the Menu Category box, the options in the Items box will only show Sandwich options. I'm stuck as how I might approach this. Once I filter out the 2nd list one time, how do I "find" the list options once I change my menu category in the 1st list? Also, if I'm thinking in SQL, I would have a key in the 1st box that would be used to link to the data in the 2nd box. However, I can't see where I have room for a "key" element in the 2nd box. How could this problem be solved with a combination of jQuery or plain javascript?

    Read the article

  • Is it possible to create a python iterator over pre-defined mutable data?

    - by Wilduck
    I might be doing this wrong, if I am, let me know, but I'm curious if the following is possible: I have a class that holds a number of dictionaries, each of which pairs names to a different set of objects of a given class. For example: items = {"ball" : ItemInstance1, "sword" : ItemInstance2} people = {"Jerry" : PersonInstance1, "Bob" : PersonInstance2, "Jill" : PersonInstance3} My class would then hold the current items and people that are availible, and these would be subject to change as the state changes: Class State: def __init__(self, items, people): self.items = items self.people = people I would like to define a iter() and next() method such that it iterates through all of the values in its attributes. My first question is whether or not this is possible. If it is, will it be able to support a situation as follows: I define items and people as above then: state = State(items, people) for names, thing in state: print name + " is " + thing.color items[cheese] = ItemInstance3 for names, thing in state: print name + " weighs " + thing.weight While I feel like this would be usefull in the code I have, I don't know if it's either possible or the right approach. Everything I've read about user defined iterators has suggested that each instance of them is one use only.

    Read the article

  • Error handling in C++, constructors vs. regular methods

    - by Dennis Ritchie
    I have a cheesesales.txt CSV file with all of my recent cheese sales. I want to create a class CheeseSales that can do things like these: CheeseSales sales("cheesesales.txt"); //has no default constructor cout << sales.totalSales() << endl; sales.outputPieChart("piechart.pdf"); The above code assumes that no failures will happen. In reality, failures will take place. In this case, two kinds of failures could occur: Failure in the constructor: The file may not exist, may not have read-permissions, contain invalid/unparsable data, etc. Failure in the regular method: The file may already exist, there may not be write access, too little sales data available to create a pie chart, etc. My question is simply: How would you design this code to handle failures? One idea: Return a bool from the regular method indicating failure. Not sure how to deal with the constructor. How would seasoned C++ coders do these kinds of things?

    Read the article

  • .Net in HTML tp return true if reader object not null, otherwise return false

    - by Phill Healey
    I'm using a DataList to show some data from the database and populating the fields on the html side. I now have a requirement to change the visibility of a panel based on whether or not a db field has data or not. I need to be able to show the panel if the relevant data field has content, and hide it if it doesn't. Eg: <asp:Panel ID="pnlNew" runat="server" Style="margin:0; padding:0; width:42px; height:18px; bottom:5px; right:10px; float:right; position:relative; background:url(../_imgVideoBadge.png) no-repeat;" Visible='<%# Eval("cheese") != null %>' ToolTip="available"></asp:Panel> Obviously this doesn't work in terms of the visible property. But hopefully it gives an idea of what I'm trying to achieve. Any help would be greatly appreciated. I've seen examples previously of doing something along the lines of: a ?? b:c How could this be applied to the above requirement?? Thanks in advance.

    Read the article

  • Javascript inheritance: call super-constructor or use prototype chain?

    - by Jeremy S.
    Hi folks, quite recently I read about javascript call usage in MDC https://developer.mozilla.org/en/JavaScript/Reference/Global_Objects/Function/call one linke of the example shown below, I still don't understand. Why are they using inheritance here like this Prod_dept.prototype = new Product(); is this necessary? Because there is a call to the super-constructor in Prod_dept() anyway, like this Product.call is this just out of common behaviour? When is it better to use call for the super-constructor or use the prototype chain? function Product(name, value){ this.name = name; if(value >= 1000) this.value = 999; else this.value = value; } function Prod_dept(name, value, dept){ this.dept = dept; Product.call(this, name, value); } Prod_dept.prototype = new Product(); // since 5 is less than 1000, value is set cheese = new Prod_dept("feta", 5, "food"); // since 5000 is above 1000, value will be 999 car = new Prod_dept("honda", 5000, "auto"); Thanks for making things clearer

    Read the article

  • Getting Values from fetched Core Data

    - by user571905
    Hi there, Thanks to the wonderful people on this forum, I have overcome most of my Core Data woes. However one persists, and I'm certain it is a simple fix. I have a recipe app that parses an XML doc on load and puts the data in Core Data. Then I search that Core Data for particular recipes, ingredients, etc. Everything is working with one exception... I cannot do anything with the data I retrieve. For example, I search the core data for "eggplant" and get this at the end of the process: "<RecipeData: 0x6112a40> (entity: RecipeData; id: 0x6113880 <x-coredata:///RecipeData/tCDE9A0EE-DA3F-4BD0-AEF8-3C038586991D4> ; data: {\n ingredients = \"Eggplant|Cheese|Tomatoes|\";\n name = \"Eggplant Parm\";\n time = 40;\n})" How do I get the info out of there? I tried looping through, but that causes the app to crash: for (NSString* key in selectedRecipe) { id value = [selectedRecipe objectForKey:key]; NSLog(@"IN LOOP: %@", value); } Any suggestions? Thank you for your time.

    Read the article

  • Vacancy Tracking Algorithm implementation in C++

    - by Dave
    I'm trying to use the vacancy tracking algorithm to perform transposition of multidimensional arrays in C++. The arrays come as void pointers so I'm using address manipulation to perform the copies. Basically, there is an algorithm that starts with an offset and works its way through the whole 1-d representation of the array like swiss cheese, knocking out other offsets until it gets back to the original one. Then, you have to start at the next, untouched offset and do it again. You repeat until all offsets have been touched. Right now, I'm using a std::set to just fill up all possible offsets (0 up to the multiplicative fold of the dimensions of the array). Then, as I go through the algorithm, I erase from the set. I figure this would be fastest because I need to randomly access offsets in the tree/set and delete them. Then I need to quickly find the next untouched/undeleted offset. First of all, filling up the set is very slow and it seems like there must be a better way. It's individually calling new[] for every insert. So if I have 5 million offsets, there's 5 million news, plus re-balancing the tree constantly which as you know is not fast for a pre-sorted list. Second, deleting is slow as well. Third, assuming 4-byte data types like int and float, I'm using up actually the same amount of memory as the array itself to store this list of untouched offsets. Fourth, determining if there are any untouched offsets and getting one of them is fast -- a good thing. Does anyone have suggestions for any of these issues?

    Read the article

  • using isight camera in macbookpro(8,2) on ubuntu 12.04 virtualbox VM

    - by Kurt Spindler
    I'm having a lot of trouble using the built-in isight camera on my macbookpro8,2 (early 2011) from an ubuntu 12.04 virtual machine, run inside VirtualBox. The following is the log I get when I try to run guvcview ubuntu@ubuntu:~$ guvcview guvcview 1.5.3 ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.surround71 ALSA lib setup.c:565:(add_elem) Cannot obtain info for CTL elem (MIXER,'IEC958 Playback Default',0,0,0): No such file or directory ALSA lib setup.c:565:(add_elem) Cannot obtain info for CTL elem (MIXER,'IEC958 Playback Default',0,0,0): No such file or directory ALSA lib setup.c:565:(add_elem) Cannot obtain info for CTL elem (MIXER,'IEC958 Playback Default',0,0,0): No such file or directory ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.hdmi ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.hdmi ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.modem ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.modem ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.phoneline ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.phoneline ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 Init. FaceTime HD Camera (Built-in) (location: usb-0000:00:0b.0-1) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 1/10, { pixelformat = 'MJPG', description = 'MJPEG' } { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { pixelformat = 'RGB3', description = 'RGB3' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { pixelformat = 'BGR3', description = 'BGR3' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { pixelformat = 'YU12', description = 'YU12' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { pixelformat = 'YV12', description = 'YV12' } { discrete: width = 160, height = 120 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 176, height = 144 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 320, height = 240 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 352, height = 288 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 640, height = 480 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1280, height = 720 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 960, height = 540 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, { discrete: width = 1024, height = 576 } Time interval between frame: 100/2997, 1/25, 1/24, 1/15, vid:05ac pid:8509 driver:uvcvideo checking format: 1196444237 VIDIOC_G_COMP:: Invalid argument compression control not supported fps is set to 1/25 drawing controls no codec detected for H264 no codec detected for MP3 - (lavc) Checking video mode 960x540@32bpp : OK Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable Could not grab image (select timeout): Resource temporarily unavailable write /home/ubuntu/.guvcviewrc OK free controls cleaned allocations - 100% Closing portaudio ...OK Closing GTK... OK ubuntu@ubuntu:~$ Any help would be greatly appreciated. Only clue I have is that I initially was having problems, tried using the old method of fixing isights (involving installing isight-firmware-tools) before realizing that I just hadn't turned on the VM setting to allow the VM to access the webcam. :) Anyway, I wonder if installing that messed something up. However, I think this is a red herring because I've: shut down and turned back on the Mac, restarted the VM, tried a different VM (for which I never installed isight-firmware-tools, and created an entirely new ubuntu vm. All instances have had this problem. Similarly, other viewers, such as cheese, avplay, avconv have had all various kinds of errors.

    Read the article

  • To Bit or Not To Bit

    - by Johnm
    'Twas a long day of troubleshooting and firefighting and now, with most of the office vacant, you face a blank scripting window to create a new table in his database. Many questions circle your mind like dirty water gurgling down the bathtub drain: "How normalized should this table be?", "Should I use an identity column?", "NVarchar or Varchar?", "Should this column be NULLABLE?", "I wonder what apple blue cheese bacon cheesecake tastes like?" Well, there are times when the mind goes it's own direction. A Bit About Bit At some point during your table creation efforts you will encounter the decision of whether to use the bit data type for a column. The bit data type is an integer data type that recognizes only the values of 1, 0 and NULL as valid. This data type is often utilized to store yes/no or true/false values. An example of its use would be a column called [IsGasoline] which would be intended to contain the value of 1 if the row's subject (a car) had a gasoline engine and a 0 if the subject did not have a gasoline engine. The bit data type can even be found in some of the system tables of SQL Server. For example, the sysssispackages table in the msdb database which contains SQL Server Integration Services Package information for the packages stored in SQL Server. This table contains a column called [IsEncrypted]. A value of 1 indicates that the package has been encrypted while the value of 0 indicates that it is not. I have learned that the most effective way to disperse the crowd that surrounds the office coffee machine is to engage into SQL Server debates. The bit data type has been one of the most reoccurring, as well as the most enjoyable, of these topics. It contains a practical side and a philosophical side. Practical Consideration This data type certainly has its place and is a valuable option for database design; but it is often used in situations where the answer is really not a pure true/false response. In addition, true/false values are not very informative or scalable. Let's use the previously noted [IsGasoline] column for illustration. While on the surface it appears to be a rather simple question when evaluating a car: "Does the car have a gasoline engine?" If the person entering data is entering a row for a Jeep Liberty, the response would be a 1 since it has a gasoline engine. If the person is entering data is entering a row for a Chevrolet Volt, the response would be a 0 since it is an electric engine. What happens when a person is entering a row for the gasoline/electric hybrid Toyota Prius? Would one person's conclusion be consistent with another person's conclusion? The argument could be made that the current intent for the database is to be used only for pure gasoline and pure electric engines; but this is where the scalability issue comes into play. With the use of a bit data type a database modification and data conversion would be required if the business decided to take on hybrid engines. Whereas, alternatively, if the int data type were used as a foreign key to a reference table containing the engine type options, the change to include the hybrid option would only require an entry into the reference table. Philosophical Consideration Since the bit data type is often used for true/false or yes/no data (also called Boolean) it presents a philosophical conundrum of what to do about the allowance of the NULL value. The inclusion of NULL in a true/false or yes/no response simply violates the logical principle of bivalence which states that "every proposition is either true or false". If NULL is not true, then it must be false. The mathematical laws of Boolean logic support this concept by stating that the only valid values of this scenario are 1 and 0. There is another way to look at this conundrum: NULL is also considered to be the absence of a response. In other words, it is the equivalent to "undecided". Anyone who watches the news can tell you that polls always include an "undecided" option. This could be considered a valid option in the world of yes/no/dunno. Through out all of these considerations I have discovered one absolute certainty: When you have found a person, or group of persons, who are willing to entertain a philosophical debate of the bit data type, you have found some true friends.

    Read the article

  • Apache sends plain-text response when accessing SSL-enabled site without HTTPS

    - by animuson
    I've never encountered something such as this before. I was attempting to simply redirect the page to the HTTPS version if it determined that HTTPS was off, but instead it's displaying an HTML page rather than actually redirecting; and even odder, it's displaying it as text/plain! The VirtualHost Declaration (Sort of): ServerAdmin [email protected] DocumentRoot "/path/to/files" ServerName example.com SSLEngine On SSLCertificateFile /etc/ssh/certify/example.com.crt SSLCertificateKeyFile /etc/ssh/certify/example.com.key SSLCertificateChainFile /etc/ssh/certify/sub.class1.server.ca.pem <Directory "/path/to/files/"> AllowOverride All Options +FollowSymLinks DirectoryIndex index.php Order allow,deny Allow from all </Directory> RewriteEngine On RewriteCond %{HTTPS} off RewriteRule .* https://example.com:6161 [R=301] The Page Output: <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>301 Moved Permanently</title> </head><body> <h1>Moved Permanently</h1> <p>The document has moved <a href="https://example.com:6161">here</a>.</p> <hr> <address>Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/1.0.0e DAV/2 Server at example.com Port 443</address> </body></html> I've tried moving the Rewrite stuff up above the SSL stuff hoping it'd do something and nothing happens. If I view the page with via HTTPS, it displays fine like it should. It's obviously detecting that I'm trying to rewrite the path, but it's not acting. The Apache error log does not indicate anything to me that might have gone wrong. When I remove the RewriteRules: <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>400 Bad Request</title> </head><body> <h1>Bad Request</h1> <p>Your browser sent a request that this server could not understand.<br /> Reason: You're speaking plain HTTP to an SSL-enabled server port.<br /> Instead use the HTTPS scheme to access this URL, please.<br /> <blockquote>Hint: <a href="https://example.com/"><b>https://example.com/</b></a></blockquote></p> <p>Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.</p> <hr> <address>Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/1.0.0e DAV/2 Server at example.com Port 443</address> </body></html> I get the standard "you can't do this because you're not using SSL" response, which is also provided in text/plain rather than being rendered as HTML. This would make sense, it should only work for HTTPS-enabled connections, but I still want to redirect them to the HTTPS connection when it determines that it is not enabled. Thinking I could circumvent the system: I tried adding a ErrorDocument 400 https://example.com:6161 to the config file instead of using RewriteRules, and that just gave me a new message, still no cheese. <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>302 Found</title> </head><body> <h1>Found</h1> <p>The document has moved <a href="https://example.com:6161">here</a>.</p> <hr> <address>Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/1.0.0e DAV/2 Server at example.com Port 443</address> </body></html> How can I force Apache to actually redirect rather than displaying a "301" page that shows HTML in plain-text format?

    Read the article

  • Silverlight Recruiting Application Part 4 - Navigation and Modules

    After our brief intermission (and the craziness of Q1 2010 release week), we're back on track here and today we get to dive into how we are going to navigate through our applications as well as how to set up our modules. That way, as I start adding the functionality- adding Jobs and Applicants, Interview Scheduling, and finally a handy Dashboard- you'll see how everything is communicating back and forth. This is all leading up to an eventual webinar, in which I'll dive into this process and give a honest look at the current story for MVVM vs. Code-Behind applications. (For a look at the future with SL4 and a little thing called MEF, check out what Ross is doing over at his blog!) Preamble... Before getting into really talking about this app, I've done a little bit of work ahead of time to create a ton of files that I'll need. Since the webinar is going to cover the Dashboard, it's not here, but otherwise this is a look at what the project layout looks like (and remember, this is both projects since they share the .Web): So as you can see, from an architecture perspective, the code-behind app is much smaller and more streamlined- aka a better fit for the one man shop that is me. Each module in the MVVM app has the same setup, which is the Module class and corresponding Views and ViewModels. Since the code-behind app doesn't need a go-between project like Infrastructure, each MVVM module is instead replaced by a single Silverlight UserControl which will contain all the logic for each respective bit of functionality. My Very First Module Navigation is going to be key to my application, so I figured the first thing I would setup is my MenuModule. First step here is creating a Silverlight Class Library named MenuModule, creatingthe View and ViewModel folders, and adding the MenuModule.cs class to handle module loading. The most important thing here is that my MenuModule inherits from IModule, which runs an Initialize on each module as it is created that, in my case, adds the views to the correct regions. Here's the MenuModule.cs code: public class MenuModule : IModule { private readonly IRegionManager regionManager; private readonly IUnityContainer container; public MenuModule(IUnityContainer container, IRegionManager regionmanager) { this.container = container; this.regionManager = regionmanager; } public void Initialize() { var addMenuView = container.Resolve<MenuView>(); regionManager.Regions["MenuRegion"].Add(addMenuView); } } Pretty straightforward here... We inject a container and region manager from Prism/Unity, then upon initialization we grab the view (out of our Views folder) and add it to the region it needs to live in. Simple, right? When the MenuView is created, the only thing in the code-behind is a reference to the set the MenuViewModel as the DataContext. I'd like to achieve MVVM nirvana and have zero code-behind by placing the viewmodel in the XAML, but for the reasons listed further below I can't. Navigation - MVVM Since navigation isn't the biggest concern in putting this whole thing together, I'm using the Button control to handle different options for loading up views/modules. There is another reason for this- out of the box, Prism has command support for buttons, which is one less custom command I had to work up for the functionality I would need. This comes from the Microsoft.Practices.Composite.Presentation assembly and looks as follows when put in code: <Button x:Name="xGoToJobs" Style="{StaticResource menuStyle}" Content="Jobs" cal:Click.Command="{Binding GoModule}" cal:Click.CommandParameter="JobPostingsView" /> For quick reference, 'menuStyle' is just taking care of margins and spacing, otherwise it looks, feels, and functions like everyone's favorite Button. What MVVM's this up is that the Click.Command is tying to a DelegateCommand (also coming fromPrism) on the backend. This setup allows you to tie user interaction to a command you setup in your viewmodel, which replaces the standard event-based setup you'd see in the code-behind app. Due to databinding magic, it all just works. When we get looking at the DelegateCommand in code, it ends up like this: public class MenuViewModel : ViewModelBase { private readonly IRegionManager regionManager; public DelegateCommand<object> GoModule { get; set; } public MenuViewModel(IRegionManager regionmanager) { this.regionManager = regionmanager; this.GoModule = new DelegateCommand<object>(this.goToView); } public void goToView(object obj) { MakeMeActive(this.regionManager, "MainRegion", obj.ToString()); } } Another for reference, ViewModelBase takes care of iNotifyPropertyChanged and MakeMeActive, which switches views in the MainRegion based on the parameters. So our public DelegateCommand GoModule ties to our command on the view, that in turn calls goToView, and the parameter on the button is the name of the view (which we pass with obj.ToString()) to activate. And how do the views get the names I can pass as a string? When I called regionManager.Regions[regionname].Add(view), there is an overload that allows for .Add(view, "viewname"), with viewname being what I use to activate views. You'll see that in action next installment, just wanted to clarify how that works. With this setup, I create two more buttons in my MenuView and the MenuModule is good to go. Last step is to make sure my MenuModule loads in my Bootstrapper: protected override IModuleCatalog GetModuleCatalog() { ModuleCatalog catalog = new ModuleCatalog(); // add modules here catalog.AddModule(typeof(MenuModule.MenuModule)); return catalog; } Clean, simple, MVVM-delicious. Navigation - Code-Behind Keeping with the history of significantly shorter code-behind sections of this series, Navigation will be no different. I promise. As I explained in a prior post, due to the one-project setup I don't have to worry about the same concerns so my menu is part of MainPage.xaml. So I can cheese-it a bit, though, since I've already got three buttons all set I'm just copying that code and adding three click-events instead of the command/commandparameter setup: <!-- Menu Region --> <StackPanel Grid.Row="1" Orientation="Vertical"> <Button x:Name="xJobsButton" Content="Jobs" Style="{StaticResource menuStyleCB}" Click="xJobsButton_Click" /> <Button x:Name="xApplicantsButton" Content="Applicants" Style="{StaticResource menuStyleCB}" Click="xApplicantsButton_Click" /> <Button x:Name="xSchedulingModule" Content="Scheduling" Style="{StaticResource menuStyleCB}" Click="xSchedulingModule_Click" /> </StackPanel> Simple, easy to use events, and no extra assemblies required! Since the code for loading each view will be similar, we'll focus on JobsView for now.The code-behind with this setup looks something like... private JobsView _jobsView; public MainPage() { InitializeComponent(); } private void xJobsButton_Click(object sender, RoutedEventArgs e) { if (MainRegion.Content.GetType() != typeof(JobsView)) { if (_jobsView == null) _jobsView = new JobsView(); MainRegion.Content = _jobsView; } } What am I doing here? First, for each 'view' I create a private reference which MainPage will hold on to. This allows for a little bit of state-maintenance when switching views. When a button is clicked, first we make sure the 'view' typeisn't active (why load it again if it is already at center stage?), then we check if the view has been created and create if necessary, then load it up. Three steps to switching views and is easy as pie. Part 4 Results The end result of all this is that I now have a menu module (MVVM) and a menu section (code-behind) that load their respective views. Since I'm using the same exact XAML (except with commands/events depending on the project), the end result for both is again exactly the same and I'll show a slightly larger image to show it off: Next time, we add the Jobs Module and wire up RadGridView and a separate edit page to handle adding and editing new jobs. That's when things get fun. And somewhere down the line, I'll make the menu look slicker. :) Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

    Read the article

  • How to check if a Webcam is broken?

    - by user84812
    I just bought an Acer Aspire 3830TG, it comes with an integrated 1.3M HD Webcam. Before buying it i tried with a bootable Lubuntu usb stick, everything worked well except for the webcam, which i thought I had to tweak. The thing is that it seems the camera should work with no problems in ubuntu. The driver is detected, I try dmesg | grep uvcvideo and the output is [ 12.226174] uvcvideo: Found UVC 1.00 device 1.3M HD WebCam (058f:b002) [ 12.245553] usbcore: registered new interface driver uvcvideo I've also tried using different software (guvcview is black when camera output is MJPG and turns to funny colors when YU12 or YV12, cheese is always black, camorama is always with funny colors...). I should have checked that it was working properly with the default os (windows) but now it's too late for that. I even booted with a official Ubuntu Quantal distro from the usb pen, and the results are the same. so, my question is: is there any way to check that the camera is righmt or broken? So, if it's broken, at least i can go to the shop, show them that it's really broken and get an external webcam for free, or st like that. cheers. UPDATE 1 Thanks, jrp. I run sudo lsinput, and the output info about my video is the following: /dev/input/event6 bustype : BUS_USB vendor : 0x58f product : 0xb002 version : 2 name : "1.3M HD WebCam" phys : "usb-0000:00:1a.0-1.3/button" bits ev : EV_SYN EV_KEY /dev/input/event7 bustype : BUS_HOST vendor : 0x0 product : 0x6 version : 0 name : "Video Bus" phys : "LNXVIDEO/video/input0" bits ev : EV_SYN EV_KEY With this info, i'm not pretty sure about running the luvcview command. If I run luvcview -d /dev/video0 -L, the output is the following: SDL information: Video driver: x11 A window manager is available Device information: Device path: /dev/video0 { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/7, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/7, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/7, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/7, 1/5, { pixelformat = 'MJPG', description = 'MJPEG' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, { pixelformat = 'RGB3', description = 'RGB3' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, { pixelformat = 'BGR3', description = 'BGR3' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, { pixelformat = 'YU12', description = 'YU12' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, { pixelformat = 'YV12', description = 'YV12' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, if i run luvcview by itself, the image is funny (blue and red colors, mainly, with myself in negative state). tx

    Read the article

  • What Makes a Good Design Critic? CHI 2010 Panel Review

    - by jatin.thaker
    Author: Daniel Schwartz, Senior Interaction Designer, Oracle Applications User Experience Oracle Applications UX Chief Evangelist Patanjali Venkatacharya organized and moderated an innovative and stimulating panel discussion titled "What Makes a Good Design Critic? Food Design vs. Product Design Criticism" at CHI 2010, the annual ACM Conference on Human Factors in Computing Systems. The panelists included Janice Rohn, VP of User Experience at Experian; Tami Hardeman, a food stylist; Ed Seiber, a restaurant architect and designer; John Kessler, a food critic and writer at the Atlanta Journal-Constitution; and Larry Powers, Chef de Cuisine at Shaun's restaurant in Atlanta, Georgia. Building off the momentum of his highly acclaimed panel at CHI 2009 on what interaction design can learn from food design (for which I was on the other side as a panelist), Venkatacharya brought together new people with different roles in the restaurant and software interaction design fields. The session was also quite delicious -- but more on that later. Criticism, as it applies to food and product or interaction design, was the tasty topic for this forum and showed that strong parallels exist between food and interaction design criticism. Figure 1. The panelists in discussion: (left to right) Janice Rohn, Ed Seiber, Tami Hardeman, and John Kessler. The panelists had great insights to share from their respective fields, and they enthusiastically discussed as if they were at a casual collegial dinner. John Kessler stated that he prefers to have one professional critic's opinion in general than a large sampling of customers, however, "Web sites like Yelp get users excited by the collective approach. People are attracted to things desired by so many." Janice Rohn added that this collective desire was especially true for users of consumer products. Ed Seiber remarked that while people looked to the popular view for their target tastes and product choices, "professional critics like John [Kessler] still hold a big weight on public opinion." Chef Powers indicated that chefs take in feedback from all sources, adding, "word of mouth is very powerful. We also look heavily at the sales of the dishes to see what's moving; what's selling and thus successful." Hearing this discussion validates our design work at Oracle in that we listen to our users (our diners) and industry feedback (our critics) to ensure an optimal user experience of our products. Rohn considers that restaurateur Danny Meyer's book, Setting the Table: The Transforming Power of Hospitality in Business, which is about creating successful restaurant experiences, has many applicable parallels to user experience design. Meyer actually argues that the customer is not always right, but that "they must always feel heard." Seiber agreed, but noted "customers are not designers," and while designers need to listen to customer feedback, it is the designer's job to synthesize it. Seiber feels it's the critic's job to point out when something is missing or not well-prioritized. In interaction design, our challenges are quite similar, if not parallel. Software tasks are like puzzles that are in search of a solution on how to be best completed. As a food stylist, Tami Hardeman has the demanding and challenging task of presenting food to be as delectable as can be. To present food in its best light requires a lot of creativity and insight into consumer tastes. It's no doubt then that this former fashion stylist came up with the ultimate catch phrase to capture the emotion that clients want to draw from their users: "craveability." The phrase was a hit with the audience and panelists alike. Sometime later in the discussion, Seiber remarked, "designers strive to apply craveability to products, and I do so for restaurants in my case." Craveabilty is also very applicable to interaction design. Creating straightforward and smooth workflows for users of Oracle Applications is a primary goal for my colleagues. We want our users to really enjoy working with our products where it makes them more efficient and better at their jobs. That's our "craveability." Patanjali Venkatacharya asked the panel, "if a design's "craveability" appeals to some cultures but not to others, then what is the impact to the food or product design process?" Rohn stated that "taste is part nature and part nurture" and that the design must take the full context of a product's usage into consideration. Kessler added, "good design is about understanding the context" that the experience necessitates. Seiber remarked how important seat comfort is for diners and how the quality of seating will add so much to the complete dining experience. Sometimes if these non-food factors are not well executed, they can also take away from an otherwise pleasant dining experience. Kessler recounted a time when he was dining at a restaurant that actually had very good food, but the photographs hanging on all the walls did not fit in with the overall décor and created a negative overall dining experience. While the tastiness of the food is critical to a restaurant's success, it is a captivating complete user experience, as in interaction design, which will keep customers coming back and ultimately making the restaurant a hit. Figure 2. Patanjali Venkatacharya enjoyed the Sardinian flatbread salad. As a surprise Chef Powers brought out a signature dish from Shaun's restaurant for all the panelists to sample and critique. The Sardinian flatbread dish showcased Atlanta's taste for fresh and local produce and cheese at its finest as a salad served on a crispy flavorful flat bread. Hardeman said it could be photographed from any angle, a high compliment coming from a food stylist. Seiber really enjoyed the colors that the dish brought together and thought it would be served very well in a casual restaurant on a summer's day. The panel really appreciated the taste and quality of the different components and how the rosemary brought all the flavors together. Seiber remarked that "a lot of effort goes into the appearance of simplicity." Rohn indicated that the same notion holds true with software user interface design. A tremendous amount of work goes into crafting straightforward interfaces, including user research, prototyping, design iterations, and usability studies. Design criticism for food and software interfaces clearly share many similarities. Both areas value expert opinions and user feedback. Both areas understand the importance of great design needing to work well in its context. Last but not least, both food and interaction design criticism value "craveability" and how having users excited about experiencing and enjoying the designs is an important goal. Now if we can just improve the taste of software user interfaces, people may choose to dine on their enterprise applications over a fresh organic salad.

    Read the article

  • What Makes a Good Design Critic? CHI 2010 Panel Review

    - by Applications User Experience
    Author: Daniel Schwartz, Senior Interaction Designer, Oracle Applications User Experience Oracle Applications UX Chief Evangelist Patanjali Venkatacharya organized and moderated an innovative and stimulating panel discussion titled "What Makes a Good Design Critic? Food Design vs. Product Design Criticism" at CHI 2010, the annual ACM Conference on Human Factors in Computing Systems. The panelists included Janice Rohn, VP of User Experience at Experian; Tami Hardeman, a food stylist; Ed Seiber, a restaurant architect and designer; Jonathan Kessler, a food critic and writer at the Atlanta Journal-Constitution; and Larry Powers, Chef de Cuisine at Shaun's restaurant in Atlanta, Georgia. Building off the momentum of his highly acclaimed panel at CHI 2009 on what interaction design can learn from food design (for which I was on the other side as a panelist), Venkatacharya brought together new people with different roles in the restaurant and software interaction design fields. The session was also quite delicious -- but more on that later. Criticism, as it applies to food and product or interaction design, was the tasty topic for this forum and showed that strong parallels exist between food and interaction design criticism. Figure 1. The panelists in discussion: (left to right) Janice Rohn, Ed Seiber, Tami Hardeman, and Jonathan Kessler. The panelists had great insights to share from their respective fields, and they enthusiastically discussed as if they were at a casual collegial dinner. Jonathan Kessler stated that he prefers to have one professional critic's opinion in general than a large sampling of customers, however, "Web sites like Yelp get users excited by the collective approach. People are attracted to things desired by so many." Janice Rohn added that this collective desire was especially true for users of consumer products. Ed Seiber remarked that while people looked to the popular view for their target tastes and product choices, "professional critics like John [Kessler] still hold a big weight on public opinion." Chef Powers indicated that chefs take in feedback from all sources, adding, "word of mouth is very powerful. We also look heavily at the sales of the dishes to see what's moving; what's selling and thus successful." Hearing this discussion validates our design work at Oracle in that we listen to our users (our diners) and industry feedback (our critics) to ensure an optimal user experience of our products. Rohn considers that restaurateur Danny Meyer's book, Setting the Table: The Transforming Power of Hospitality in Business, which is about creating successful restaurant experiences, has many applicable parallels to user experience design. Meyer actually argues that the customer is not always right, but that "they must always feel heard." Seiber agreed, but noted "customers are not designers," and while designers need to listen to customer feedback, it is the designer's job to synthesize it. Seiber feels it's the critic's job to point out when something is missing or not well-prioritized. In interaction design, our challenges are quite similar, if not parallel. Software tasks are like puzzles that are in search of a solution on how to be best completed. As a food stylist, Tami Hardeman has the demanding and challenging task of presenting food to be as delectable as can be. To present food in its best light requires a lot of creativity and insight into consumer tastes. It's no doubt then that this former fashion stylist came up with the ultimate catch phrase to capture the emotion that clients want to draw from their users: "craveability." The phrase was a hit with the audience and panelists alike. Sometime later in the discussion, Seiber remarked, "designers strive to apply craveability to products, and I do so for restaurants in my case." Craveabilty is also very applicable to interaction design. Creating straightforward and smooth workflows for users of Oracle Applications is a primary goal for my colleagues. We want our users to really enjoy working with our products where it makes them more efficient and better at their jobs. That's our "craveability." Patanjali Venkatacharya asked the panel, "if a design's "craveability" appeals to some cultures but not to others, then what is the impact to the food or product design process?" Rohn stated that "taste is part nature and part nurture" and that the design must take the full context of a product's usage into consideration. Kessler added, "good design is about understanding the context" that the experience necessitates. Seiber remarked how important seat comfort is for diners and how the quality of seating will add so much to the complete dining experience. Sometimes if these non-food factors are not well executed, they can also take away from an otherwise pleasant dining experience. Kessler recounted a time when he was dining at a restaurant that actually had very good food, but the photographs hanging on all the walls did not fit in with the overall décor and created a negative overall dining experience. While the tastiness of the food is critical to a restaurant's success, it is a captivating complete user experience, as in interaction design, which will keep customers coming back and ultimately making the restaurant a hit. Figure 2. Patnajali Venkatacharya enjoyed the Sardian flatbread salad. As a surprise Chef Powers brought out a signature dish from Shaun's restaurant for all the panelists to sample and critique. The Sardinian flatbread dish showcased Atlanta's taste for fresh and local produce and cheese at its finest as a salad served on a crispy flavorful flat bread. Hardeman said it could be photographed from any angle, a high compliment coming from a food stylist. Seiber really enjoyed the colors that the dish brought together and thought it would be served very well in a casual restaurant on a summer's day. The panel really appreciated the taste and quality of the different components and how the rosemary brought all the flavors together. Seiber remarked that "a lot of effort goes into the appearance of simplicity." Rohn indicated that the same notion holds true with software user interface design. A tremendous amount of work goes into crafting straightforward interfaces, including user research, prototyping, design iterations, and usability studies. Design criticism for food and software interfaces clearly share many similarities. Both areas value expert opinions and user feedback. Both areas understand the importance of great design needing to work well in its context. Last but not least, both food and interaction design criticism value "craveability" and how having users excited about experiencing and enjoying the designs is an important goal. Now if we can just improve the taste of software user interfaces, people may choose to dine on their enterprise applications over a fresh organic salad.

    Read the article

< Previous Page | 1 2 3 4 5 6  | Next Page >