Search Results

Search found 2591 results on 104 pages for 'dell powervault'.

Page 5/104 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• DELL Inspiron 9400 SD Card Reader not working on 10.11 ubuntu

  - by Mario Martz

  Im new in linux, just installed Ubuntu 11.10 in a Dell Inspiron 9400, everything works fine with the exception of the SD card reader, everytime I insert a card the computer doesnt do anything, its like the SD card reader is not there. I did a $lspci and it shows the next drivers 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) Everytime I insert a memory card, dmesg shows the next d status 0x600b00 [ 2687.227351] end_request: I/O error, dev mmcblk0, sector 64 [ 2687.229436] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.229440] end_request: I/O error, dev mmcblk0, sector 65 [ 2687.230512] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.230515] end_request: I/O error, dev mmcblk0, sector 66 [ 2687.231588] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.231592] end_request: I/O error, dev mmcblk0, sector 67 [ 2687.232674] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.232678] end_request: I/O error, dev mmcblk0, sector 68 [ 2687.234763] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.234766] end_request: I/O error, dev mmcblk0, sector 69 [ 2687.236864] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.236868] end_request: I/O error, dev mmcblk0, sector 70 [ 2687.238942] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.238946] end_request: I/O error, dev mmcblk0, sector 71 [ 2687.238949] Buffer I/O error on device mmcblk0, logical block 8 [ 2687.241028] mmcblk0: retrying using single block read [ 2687.243104] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.243108] end_request: I/O error, dev mmcblk0, sector 64 [ 2687.245212] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.245215] end_request: I/O error, dev mmcblk0, sector 65 [ 2687.247298] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.247302] end_request: I/O error, dev mmcblk0, sector 66 [ 2687.248389] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.248393] end_request: I/O error, dev mmcblk0, sector 67 [ 2687.250476] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.250480] end_request: I/O error, dev mmcblk0, sector 68 [ 2687.252617] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.252621] end_request: I/O error, dev mmcblk0, sector 69 [ 2687.254737] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 and more of the same but with different sector number Im using Kernel 3.0.0-12-generic By the way, when I was installing it and ubuntu asks about installation (If I want to install it along with windows or delete something or change the partitions of the HDD) if I go to the window to change the partition of the disc, linux detects the SD Card (if there's one inserted course). Any help with this it would be appreciated -sorry for my english Thank you

  Read the article

• Can the Dell PowerEdge T320 boot from a USB stick in hard drive emulation mode?

  - by Icydog

  I am trying to install FreeNAS on a Dell PowerEdge T320. I've followed the instructions here (http://doc.freenas.org/index.php/Burning_an_IMG_File) to write the .img file to four different USB sticks with dd if=FreeNAS-9.2.1.5-RELEASE-x64.img of=/dev/sde, but I can't boot off of any of them. When I try to boot, I get the following screen: F1 FreeBSD F2 FreeBSD F3 Drive 0 Then it auto-selects F1 and either prints # about once a second forever, or it sits with a blinking cursor doing nothing. Forum posts and the wiki page linked above say to set the USB boot emulation mode to hard disk (as opposed to auto or CD/DVD/floppy), and older Dell PowerEdge models including the T310 have this option in the BIOS settings, but I cannot find it on the T320 with the latest BIOS 2.1.2. I have even tried writing the USB image to a USB hard disk, but with the same lack of success. Has anyone been able to find this USB boot setting on a T320, or been able to boot FreeNAS/FreeBSD from USB in some other way on a T320?

  Read the article

• How do I disable the middle button on the touchpad on a Dell Precision M2400?

  - by Justin

  How do I disable the middle button on the touch pad on a Dell Precision M2400?

  Read the article

• Is Dell's server software bundle necessary? (Poweredge 2950 in my case)

  - by bwerks

  Hi all, Dell includes a fair amount of software with its servers, but I'm having a hard time determining from the documentation what each of them does, and whether or not I should install it. Dell's support site (unless I'm doing it wrong) seems fairly opaque to me and its offerings fairly unstandardized in terms of their usage, so if possible I'd like to stray away from them. Specifically, I'm curious if any of the features offered are duplicated in something like Microsoft System Center. For additional background information, I'm working with a Poweredge 2950 that was just rebuilt with an expanded raid-6, but initially I just installed Server 2008 R2 directly instead of using the Build and Update utility. There's nothing of use on it at the moment so I'm totally open to wiping it again.

  Read the article

• Installing ubuntu server as linux distro on dell server - what drivers will be missed

  - by Cookie

  Dell (via USC) unpacks specific drivers for both RedHat and Suse to use after installation on its servers. As Ubuntu server isn't officially supported, this clearly isn't happening for Ubuntu. Is Ubuntu server then running with native drivers? In that case, which drivers are native with Ubuntu, and aren't (e.g. are Dell replaced) with RedHat/Suse? Are dell optimized drivers available for Ubuntu somewhere? Can the ones for RedHat or Suse be used with Ubuntu? Are there disadvantages of this lack of fine-tuned drivers, and if yes, what are they? Would they make the switch (and extra costs, as both RedHat and Suse Enterprise aren't cheap) away from the free Ubuntu server worthwhile? Dell recommends Canonical's commercial support for Ubuntu server on its machines, is this recommendable? Do they offer fine-tuned Dell drivers to replace native drivers?

  Read the article

• Getting access to physical drives in ESXi v5.5 installation on Dell PowerEdge R710 with PERC 6/i

  - by Big-Blue

  I've acquired a Dell PowerEdge R710 server a few days ago, which includes a PERC 6/i RAID controller. The server is now fitted with a SATA SSD, one SAS drive and four SATA HDD's, all of which I would like to be passed through to ESXi in an "as-is" state, without creating any logical drives in the RAID controller. Now, the ESXi v5.5 installation image I grabbed from the Dell homepage starts just fine but only lists the logical drives and connected flash drives as possible installation targets, not any of the physical drives. If I create a small logical drive on my SSD (which the PERC 6/i detects as SATA-SSD type), the ESXi install wizard lists the SSD value on that drive as false; which is far from optimal. I have also tried disabling the RAID controller entirely in the setup, but that also did not help. Everything that should enable passthrough is enabled in BIOS, but that shouldn't be a concern at this early stage of the ESXi installation. How would I be able to install ESXi v5.5 to a part of my SSD that is connected to the storage controller, while giving it entire physical access to the disk (to allow for SMART values to be read etc.)?

  Read the article

• Temperature monitoring on Dell Precision M4500 under Linux: sensors-detect doesn't, what next?

  - by Tikitu

  I have a Dell Precision M4500, Intel Core i5 CPU, running Linux (Ubuntu Lucid), and would like to keep an eye on CPU temperature. I've tried lm-sensors: sensors-detect didn't find any sensors; following its hint ("This is relatively common on laptops, where thermal management is handled by ACPI rather than the OS.") I tried acpi -V but got nothing thermal. The Gnome panel applet "Hardware Sensors Monitor" reports on GPU temperature but nothing else. What should I be trying next?

  Read the article

• Overheating on Dell Studio XPS 1645

  - by pjtatlow

  So I was wondering if anyone else has come upon this problem, and/or has come up with a solution. When I use my Ubuntu partition, my computer becomes extremely hot, and the fan runs very noisily for a very long time. If I reboot into windows while this is happening, my computer actually begins to cool down while doing the exact same tasks. Thinking this might just be a bug with Ubuntu, I installed fedora on another partition, and the same problem occurs. Is this a problem with the kernel? Cpufreq tells me that my CPU is running at 933 MHz out of a possible 1.6 GHz from my Intel Core i7 CPU Q70. For anyone who wants more information, I have 8 GB of memory, and an ATI Mobility Raedon HD 5730 Graphics Card. I'm open to any ideas anyone might have. Thanks in advance!

  Read the article

• BCM 4306 not recognized after upgrade on a Dell Latitude D600

  - by Brian Eisemann

  This is extremely frustrating to me. I had the wireless card working before I upgraded to 11.10. At first the wireless device was recognized but it told me there was no firmware, so I went ahead and went through the process I did before of installing the b43/b43legacy firmware, and now my wireless device is not even recognized, or showing up anywhere! 02:03.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11a/b/g [14e4:4324] (rev 03)

  Read the article

• Ubuntu 13.10 and Dell Inspiron 7520 SE (Intel 4000 and ATI radeon HD 7730m)

  - by pjgowtham

  I installed 13.10 and i have problems with my display. Everything else works fine. I cant control my brightness. I thought the graphics driver is the problem. So i went to software updates, switched to another driver (proprietary) and the Ubuntu screen went black and i wasn't able to boot either. I cant use my lap with such low brightness. Then i reinstalled 13.10 again, This time full hdd reset. Same problem occurred. I grabbed radeon hd7730m for Linux x64 from the amd site, installed it, and the screen went black with only the "x" cursor showing on the next boot. What should i need to do to make my brightness work and stabilize graphic cards as mine is switchable graphics type.

  Read the article

• Dell wireless not working after upgrade

  - by Omer Saeed

  So, the short version of my sad story is that I tried upgrade Ubuntu to 12.04 and wireless driver has stopped working. I have tried all the solutions but nothing seem to be working. When I try to install my wireless from "Additional Drivers" Its says: Sorry, installation of this driver failed. Please have a look at the log file for details: /var/log/jockey.log The lspci command gives me the following info about wireless: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) I have tried removing bcm drivers and reinstalling, but nothing seems to be working. rfkill is good too.

  Read the article

• ubuntu 14 painfully slow on dell r200

  - by sirmonkey

  I didn't notice it at first. The machines (there is 20 plus) are to be used a simple file servers. It wasn't until samba just wouldn't act right that I installed a desktop gui and started more diagnoseing the problem did I catch the slow preformance... I've tested 4 servers they all suck. And windows 7 runs fantastic on them. I have Google and searched. But nothing to explain this. The easy test is dmesg is so slow you can almost read it. I'm guessing it's an apic or cpu power management issue. What output would you all like????? It is a core2 machine with 4Gb of ram. On board data.

  Read the article

• Ethernet not working on a Dell Inspiron 14z

  - by Izabela

  When I plug in a network cable, it is not recognized. The WI-FI is working properly, though. ifconfig output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1645 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:206840 (206.8 KB) TX bytes:206840 (206.8 KB) wlan0 Link encap:Ethernet HWaddr e0:06:e6:de:57:e7 inet addr:150.164.201.145 Bcast:150.164.201.255 Mask:255.255.255.0 inet6 addr: 2001:12f0:601:a921:98a2:3dd:3be8:c483/64 Scope:Global inet6 addr: 2001:12f0:601:a921:e206:e6ff:fede:57e7/64 Scope:Global inet6 addr: fe80::e206:e6ff:fede:57e7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23892 errors:0 dropped:0 overruns:0 frame:0 TX packets:14676 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30123226 (30.1 MB) TX bytes:2189050 (2.1 MB)

  Read the article

• Ethernet not working in 12.04 (Dell Inspiron 14z)

  - by Izabela

  When I plug in a network cable, it is not recognized. The WI-FI is working properly, though. ifconfig output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1645 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:206840 (206.8 KB) TX bytes:206840 (206.8 KB) wlan0 Link encap:Ethernet HWaddr e0:06:e6:de:57:e7 inet addr:150.164.201.145 Bcast:150.164.201.255 Mask:255.255.255.0 inet6 addr: 2001:12f0:601:a921:98a2:3dd:3be8:c483/64 Scope:Global inet6 addr: 2001:12f0:601:a921:e206:e6ff:fede:57e7/64 Scope:Global inet6 addr: fe80::e206:e6ff:fede:57e7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23892 errors:0 dropped:0 overruns:0 frame:0 TX packets:14676 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30123226 (30.1 MB) TX bytes:2189050 (2.1 MB)

  Read the article

• Dell Vostro 1510 trackpad

  - by user18055

  A week ago I moved totally from Windows 7 to Ubuntu. I've been really happy with the transition bar one annoying glitch. My trackpad sometimes works, sometimes doesn't. All other hardware including peripherals work flawlessly, including a Logitech ball mouse, Wacom Bamboo pen and touch and wireless Logitech keyboard and mouse combo. I can't see any pattern to when and why the trackpad works. Occasionally on rebooting, it will work, but then I can reboot 10x in a row and it won't work, then I leave it a day, then reboot and it works flawlessly. Any ideas on a solution or appropriate method for me to deb it? My knowledge of Ubuntu/Linux is sketchy at best so I could do with a little help :)

  Read the article

• Dell Mini 10 Mouse Pad Problems

  - by MetaDark

  After going from 10.04 - 10.10 (not upgraded, completely reinstalled because of upgrade issues) I found a weird problem with my mouse pad. Whenever I clicked on the left or right mouse buttons (integrated into the touch pad) when I released them, it seemed like it was detecting a double click and ended up choosing the option the mouse was hovering over. Has anyone else experienced issues like this, and if it is possible, could I fix it?

  Read the article

• huwai 1731 ( mobile broadband ) not working with dell inspiron 3521

  - by N.Ramkumar

  Please help, one of my friend shared this note ( enclosed below), I used these codes and my laptop is able open the data card but I am not getting any signals. I am able to work with wired connection, but wi-fi and mobile broad band are not working. Please help. sudo apt-get purge usb-modeswitch sudo apt-get update sudo spt-get install usb-modeswitch sudo apt-get update gksudo gedit /lib/udev/rules.d/40-usb_modeswitch.rules Once you enter these above commands 40-usb_modeswitch.rules text file will open. Then, copy below mentioned lines into 40-usb_modeswitch.rules text file. #Huawei E1731 ATTRS{idVendor}=="12d1", ATTRS{idProduct}=="1446", RUN+="usb_modeswitch '%b/%k'" Save the file Then type : sudo apt-get update Then restart the machine.

  Read the article

• Howo to get Multipath IO with Dell MD3600i into active/active setup?

  - by Disco

  I'm desperately trying to improve performance of my SAN connection. Here's what i have: [root@xnode1 dell]# multipath -ll mpath1 (36d4ae520009bd7cc0000030e4fe8230b) dm-2 DELL,MD36xxi [size=5.5T][features=3 queue_if_no_path pg_init_retries 50][hwhandler=1 rdac][rw] \_ round-robin 0 [prio=200][active] \_ 18:0:0:0 sdb 8:16 [active][ready] \_ 19:0:0:0 sdd 8:48 [active][ghost] \_ 20:0:0:0 sdf 8:80 [active][ghost] \_ 21:0:0:0 sdh 8:112 [active][ready] And multipath.conf : defaults { udev_dir /dev polling_interval 5 prio_callout none rr_min_io 100 max_fds 8192 user_friendly_names yes path_grouping_policy multibus default_features "1 fail_if_no_path" } blacklist { device { vendor "*" product "Universal Xport" } } devices { device { vendor "DELL" product "MD36xxi" path_checker rdac path_selector "round-robin 0" hardware_handler "1 rdac" failback immediate features "2 pg_init_retries 50" no_path_retry 30 rr_min_io 100 prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } And sessions. [root@xnode1 dell]# iscsiadm -m session tcp: [13] 10.0.51.220:3260,1 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [14] 10.0.50.221:3260,2 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [15] 10.0.51.221:3260,2 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [16] 10.0.50.220:3260,1 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c I'm getting very poor read performance : dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=1000 The SAN is configured as follows: CTRL0,PORT0 : 10.0.50.220 CTRL0,PORT1 : 10.0.50.221 CTRL1,PORT0 : 10.0.51.220 CTRL1,PORT1 : 10.0.51.221 And on the host : IF0 : 10.0.50.1 IF1 : 10.0.51.1 (Dual 10GbE Ethernet Card Intel DA2) It's connected to a 10gbE switch dedicated for SAN traffic. My questions being; why the connection is set up as 'ghost' and not 'ready' like an active/active configuration ?

  Read the article

• Dell Inspiron 1564 overheating but fan not switching on, how to diagnose?

  - by Smugrik

  I've got a Dell Inspiron 1564 laptop that is about one and a half years old. Since about a week, the laptop started to overheat, causing it to switch off unexpectedly... The cpu fan is working erratically, it can start to spin for a while, doing its job and cooling down the cpu before it stops, but then the temperature goes up, and the fan doesn't reacts, once the temperature reaches a critical point (over 85 celsius, checked with speedfan...), the laptop switches off... I already cleaned the vents and fan from dust, to no avail, and it was actually quite clean anyway. Drivers and bios are up-to-date, no crapware was ever installed on this machine. I don't know how to diagnose the problem, could it be the temperature sensors that sends wrong information, so the fan doesn't reacts? but then I believe the computer wouldn't detect the overheat and stop... Is there a way I can pin point the problem? Maybe some low-level diagnostic tools to check functionality of sensors and fans??? The warranty is already over so any suggestion would be welcome. Thanks!!

  Read the article

• dell server display on laptop screen

  - by hari

  Please redirect if this is not (and probably thats true) the correct forum/site. I have a dell server and I am trying to configure it for the first time. It is running windows server 2003. I do not have a monitor screen. Can I use laptop screen to display dell server and set it up? I mean to say is, if I can display dell server on laptop screen, it would be great. I am trying that with a dell laptop but not getting the display. Any help/pointer would be appreciated. Thanks in advance.

  Read the article

• Restrict IPMI access on Dell BMC and iDRAC to an allowed IP range

  - by edgester

  I'm trying to secure the iDRAC's and BMC's on some of my Dell servers (R210, R410, R510). I want to restrict access to IPMI commands to only a few IP addresses. I've successfully restricted access to the iDrac using the instructions from http://support.dell.com/support/edocs/software/smdrac3/idrac/idrac10mono/en/ug/html/racugc2d.htm#wp1181529 , but the IP restrictions do not affect IPMI. A separate management network is not practical at this time because of lack or ports and some Dell BMC's don't offer a separate port. I'm told by my networking group that our switches don't support trunking, so using the vlan tagging is not an option either. Is there a way restrict the IPMI access to a list of allowed addresses? FYI, for various reasons, I have a mix of Dell servers with BMC's, iDrac Express and iDrac enterprise management features.

  Read the article

• Trouble with wireless driver on a Dell Latitude D830

  - by Kevin

  After uninstalling Dell's wireless utility I get a new hardware found dialog that can not find any driver for my wifi card on it's own. I'm running Windows XP Professional Service Pack 3, and I would like to use the default wifi handler since dell's utility does not work with my company's wireless switch. I did try downloading the recommend driver from the dell support site Network Adapter 2 Model Intel(R) PRO/Wireless 3945ABG Network Connection Description [12] Intel(R) PRO/Wireless 3945ABG Network Connection Status Connected

  Read the article

• Installing VMware ESXi 4.0 on Dell 1950: Cannot open vmkboot.gz

  - by rlandster

  I am trying to install VMware ESXi 4.0.0 U1 on a Dell 1950 server via a bootable CD-ROM. I keep getting this error right at the start: Cannot open vmkboot.gz I checked that the CD-ROM drive is not to blame by installing Debian Etch using that drive. I tried several different versions of ESXi (3.5, 3.5 Dell edition, 4.0 Dell edition) and they all give me an error at the same place. I also tried installing from a USB "thumb" drive but got the same error. I checked with the VMware HCL (Hardware Compatibility List) and the Dell 1950 is listed as being compatible. Here are some server details: Two 1.6 GHz Xeon 5110 CPUs (ID: 06-0F-B) BIOS version 2.2.6 Any ideas on what might be the issue?

  Read the article

• Using a non-validated SED on a Dell R720

  - by a coder

  We were given a Dell R720 a couple years ago, and the machine currently has standard 300GB 3.5" SAS 15k drives. Our RAID controller is a Perc H710. We need to update our disks to FIPS 140-2 certified SED. According to Dell, they have only one tested/validated FIPS SED for this machine/controller, but it is a 7200rpm 3.5" unit. I'm showing that Dell offers a 600GB 15k FIPS SED in 3.5" configuration (Dell part number 342-0605), but they say they haven't validated or tested to know if it works. They informed us that we would not void our warranty in using this non-validated drive. How likely is it that our R720 with H710 controller will work with the non-validated drive? Are there significant differences in how drive manufacturers build SED that would prevent them from working consistently across different controllers?

  Read the article

• Docking Station Sound Doesn't Work on Dell D830 with Windows 7

  - by cisellis

  I have a Dell Latitude D830 laptop that is running Windows 7 Enterprise x64. I connect to a docking station during the day with multiple monitors, a keyboard and a mouse. Everything runs with no problems including most of the docking station ports (usb, monitors, etc.) However, the sound port from the docking station does not work since the upgrade to Windows-7. Even with the laptop plugged in, the sound always comes out of the laptop, not the headphones plugged into the docking station. Here's what I've tried: I've seen other issues like via Google this that seem to be mostly unanswered. I found one or two that referenced using the Vista x64 drivers, especially the Nvidia drivers. I do not have an Nvidia chipset but I've reinstalled the sound drivers and that has not helped. I don't have a support contract and considering the cost is usually high to call Dell, that's not an option. Dell's forums are pretty much a wasteland and I've found no help there. Since this is a docking station I thought I might need to try the SATA or Intel chipset drivers from the dell site instead, however I'm not really sure and I need to work on this laptop in the meantime. I can't really afford the downtime to experiment with random drivers all day in case they turn out to be incompatible (Dell still hasn't added Windows 7 to their support site as far as I can tell). Does anyone have any other ideas? Has anyone had this issue and solved it? If so, how? Thanks in advance for your help.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >