Search Results

Search found 11822 results on 473 pages for 'external assembly'.

Page 5/473 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Unable to mount 1TB USB external HDD - Error

  - by superbDeveloper

  Hi, I'm getting an error when I plug in my 1TB USB external HDD, the wierd thing about this is that it was working fine before and I've been using it for about a couple of months now. yesterday I compressed one of the folders which had about 120GB of data but the compression failed after an hour and I decided to unmount the drive and shut everything down. Today when I tried to plug in the drive I got the following error: Error mounting: mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so output of cat /proc/partitions below muzikayise@muzikayise-supercom:~$ sudo fdisk -l /dev/sdc Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x39dcba64 Device Boot Start End Blocks Id System please will someone kindly assist with this? thanks in advance,

  Read the article

• External display suddenly not detected

  - by NChase

  I have a Lenovo IdeaPad U410 running Ubuntu Desktop 13.04. I have an external monitor that I connect to via HDMI, and it's worked flawlessly for six months. I plug in my laptop, it detects the display. The "change display" key built into the laptop works for switching between the two screens. Never any problems. This afternoon, when I reconnected my computer after taking it into another room for a bit, it didn't work. When I open up Display settings, it can't detect the display. I tried disconnecting/reconnecting everything multiple times. And most strangely, that same "change display" key now behaves like a Super key, opening the dash instead of toggling the display. Nothing at all changed between when I plugged it in this morning and when it stopped working a few hours later. I tried xrandr, that doesn't detect it either. Anyone have any ideas?

  Read the article

• Plugging two external screens to laptop via VGA and HDMI

  - by avilella

  I have an Asus U30JC laptop with a VGA and HDMI ports. I can connect my external screen (1920x1200) to either of those ports but I wonder if I would be able to use two screens at the same time, one plugged to the VGA and the other to the HDMI socket. Any ideas? Where should I find out? Doing xrandr, I get: Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 293mm x 164mm 1366x768 60.0*+ 1360x768 59.8 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 disconnected (normal left inverted right x axis y axis) DP1 disconnected (normal left inverted right x axis y axis)

  Read the article

• Pointer problem on external monitor

  - by Herby Pepper

  Pointer looks and work fine on laptop but when I connect external monitor it appears there as a shaking, square shape. Videos are not showing either. my laptop hp 2133: Graphic card: VIA Technologies, Inc. CN896/VN896/P4M900, Chrome 9 HC. System: Lubuntu 12.04 I think it is graphic problem but can't find drivers for my card and system. I do have xserver-xorg-video-openchrome and disper installed. I did not have that problem with Lubuntu 11.10. My problem is a bit like : Mouse pointer strange problem but it was not solved so I decided to post my question.

  Read the article

• Know more about Assembly

  - by Ralax

  If you want to know what an assembly does, you can use Reflector to refactor the assembly and check the codes. If you want to know why binding assembly failed, you can use Assembly Binding Log Viewer to check it. Also you should set HKLM\Software\Microsoft\Fusion\ForceLog registry value to 1 . When the assembly is used, you want to know what the assembly uses, you can use Process Explorer ....(read more)

  Read the article

• eepc 100h ubuntu 12.04 external monitor higher resolution modes force a rotated display

  - by Acky

  Hi I have a eeepc 1000h netbook. I've just installed ubuntu. I mainly use an external display (samsung ta350 full hd 22 inch affair) but when I select 1080 from the dropdown list, my only options are for a rotated portrait. My neck's non too supple, so tilting my head for extended periods is not really viable. :-) Any ideas on making ubuntu display 1080 normal landscape? It must surely be possible. My gparted boot cd does it perfectly. Any help greatly appreciated. Cheers!

  Read the article

• external disk dont work on ubuntu

  - by Skirki

  i have problem with in my ubuntu: when i connect external imation apollo disc i dont see a file system. Disk is working because in windows OS on this same computer it works as well. when i typed dmesg i got following logs [12913.260078] usb 4-1: new low speed USB device using ohci_hcd and address 15 [12913.440072] usb 4-1: device descriptor read/64, error -62 [12913.730058] usb 4-1: device descriptor read/64, error -62 [12914.020085] usb 4-1: new low speed USB device using ohci_hcd and address 16 [12914.200082] usb 4-1: device descriptor read/64, error -62 [12914.490150] usb 4-1: device descriptor read/64, error -62 [12914.780064] usb 4-1: new low speed USB device using ohci_hcd and address 17 [12915.200070] usb 4-1: device not accepting address 17, error -62 [12915.380081] usb 4-1: new low speed USB device using ohci_hcd and address 18 [12915.800065] usb 4-1: device not accepting address 18, error -62 [12915.800100] hub 4-0:1.0: unable to enumerate USB device on port 1 i trying to fix that by use commands: cd /sys/bus/pci/drivers/ehci_hcd echo -n "0000:00:02.1" unbind but it did not match the result and i don't have any other idea

  Read the article

• default mount point changed for external HD

  - by JhmL

  The default mount point for my external HD changed when upgrading from 13.04 to 13.10. Now the username is added as an extra level before the hd label. So it used to be /media/nameofhd and now it became /media/username/nameofhd This breaks a lot of links I have set up to this disk. I know that I can mount it manually and even automatically through /etc/fstab. What I want to know is why this behaviour changed and how I can change it back to the original? blkid and fdisk don't show anything suspicious. thx!

  Read the article

• Control external monitor brightness

  - by remi

  Hello Ubuntu community, I can control the brightness of my DELL U2713HM connected with DisplayPort via the command: ddccontrol -p -r 0x10 -w 53 where in this example the number 53 represents the brightness level (range 0 to 100). But I don't know how to link the command to my brightness keys on my keyboard. I searched already, but just found answers to integrated laptop screens. In /sys/class/backlight is the folder acpi_video0 with some subfolders and files. The file actual_brightness contains a number from 0 to 20, which is changing when I press the brightness keys. How do I get my external monitor listed as a device in /sys/class/backlight ? PS: I am running a fresh Ubuntu 12.10 install with integrated graphics Intel HD4000.

  Read the article

• Mount external HD ubuntu 12.10

  - by Luigi Tiburzi

  Although it's an abundantly treated matter, I'm unable to find an answer valid for my needs. I had a 12.04 installation of ubuntu and I decided to install the 12.10. I copied (using GParted) the partition where my system was to an external hd where there is a windows partition. Then I installed the newest ubuntu version and now I want to take back some files (for example my .emacs) from that partition but when I try to mount it, it is not found as sdb and if I mount it from /dev/usb/hddev0 I don't get any output, only a blinking cursor, no errors, no output. I even tried to mount it as an ntfs disk but the result was the same. It's like the hd cannot be detected. So how can I access data to that disk? Could I get them from GParted terminal instead of Ubuntu one? Thanks

  Read the article

• External hard-drive is "clicking" when idle [closed]

  - by mirumir

  I'm struggling with a very annoying issue: My new hard-drive (Samsung Spinpoint M8 1TB (HN-M101MBB) was build in an USB 3.0 external case (Lian Li EX-10QR) and formatted with ext4. When this hard-drive is connected to my Notebook via USB 2.0 it "klicks", the LED flashs too, every second, but only when it's idle! It stays silent, when something is copying or reading from it. But when this drive was formatted with ext3 or fat, it always remained silent. This also happens with a Western Digital WD10JPVT Scorpio Blue, but the "klicks" are even louder! System: 12.04 64-bit with Gnome-Shell. Any ideas how to approach this issue?

  Read the article

• Switching to an external display, when primary is broken

  - by Shazzner

  I've successfully install Ubuntu 11.10 Desktop (x86) on an old(er) laptop that unfortunately has a broken screen, so there is an external monitor plugged in. On the livecd it come up on the secondary display just fine and I was able to install ubuntu and everything. Unfortunately when I reboot into Ubuntu proper now, the secondary display is off and I'm literally driving blind here trying to switch it to the secondary display. Using Nvidia open source drivers. Things I've tried: Rebooting back into livecd, mounting the partition and trying in vain to find a config file (it uses the open source drivers so no Xorg.conf I could edit manually) Trying to blind-type xrandr settings into what I hope is terminal: xrandr --output VGA1 --auto (nothing happened) Trying to blind install openssh-server so I could ssh into it and maybe configure it from my working computer. For some reason though, no luck. Ubuntu really should default to expanding to all screens for this use case.

  Read the article

• External TV only allows 640x480 using VGA cable

  - by EdC

  I have Ubuntu precise installed on a MacBook Pro. When connecting to an external television using a VGA style cable the highest resolution available seems to be 640x480. I'm using the proprietary NVIDEA Accelerated Graphics Driver (version current) and attempting to setup the TV using the nvidea-settings tool. I know all the equipment supports higher resolutions because of the following: Prior to rebuilding my machine with precise, the same TV, cabel & adapter gave higher resolutions The same machine & TV when used with a HDMI cable allows higher resolutions Windows laptops with the same cable & TV are able to achieve higher resolutions I'm not sure what to look for next, there are some similar FAQ questions but I'm not sufficiently familiar with the areas involved to know if these are my issue or are safe to try. Specifically: colord problem & my monitor resolution 640*480 with no other options! - is the closest, but as I'm having no problems with the main laptop monitor I'm not sure the described symptoms apply. I can't work out from the answer or Bumblebee site how to determine if nvidia optimus applies to my laptop. Why isn't my monitor's native resolution appearing as an option? - suggests configuring X by hand, but doesn't entirely match the symptoms I'm seeing

  Read the article

• external usb hard drive is not being seen anymore

  - by incrediblehulk

  I think my problem is a little different than several other similar titled questions. Everything started while I was using 10.10. External drive was always recognized and mounted, but the timing of this differed. I mean when I booted, the OS sometimes saw the drive immediately, sometimes after a few minutes, sometimes after hours. Although this was annoying, I tolerated this somehow. Then this problem persisted after I upgraded to 11.04 with a clean install. Afterwards, the drive became totally invisible to the OS. It is not even detected as an usb device anymore. However, there is one thing I can do to make it seen. If I boot to another operating system which can detect the drive, and then boot back to ubuntu, everything is perfect. but this is of course very impractical. To summarize, the usb drive is recognized by ubuntu if and only if another OS in the same computer could recognize it first. I should also say I have not had any problems with the same drive in any other OS or a different computer. My drive is philips with a hitachi hdd inside, has its own power source and any other usb powered drives have never caused this kind of a problem. I've tried almost all recommendations in similar topics but none of them seems to be related to this one. What can I possibly do to fix this?

  Read the article

• Unable to Mount an external hard drive (NTFS)

  - by Mediterran81

  Ubuntu 11.10. When I plug my external Drive Western Digital MyPassport (500Go NTFS) I named WD. I get the following error: Unable to mount WD Error mounting: mount exited with exit code 1: helper failed with: mount: according to mtab, /dev/sdb1 is already mounted on /media/WD mount failed I have no problem with the internal NTFS partitions that auto-mounts on startup (ntfs-config does that). If I plug the WD before I boot Ubuntu, upon login, it's recognized and I can access without no problem. But if I remove it using (Safely remove) and then replug it, I get the error above. Here is my fstab: # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 #Entry for /dev/sda5 : UUID=24540d0f-5803-493c-ace9-e3b3c0cedb26 / ext4 errors=remount-ro 0 1 #Entry for /dev/sda3 : UUID=E4C43F7EC43F51D2 /media/OS ntfs-3g defaults,locale=en_US.UTF-8 0 0 #Entry for /dev/sda2 : UUID=6A0070F10070C61B /media/RECOVERY ntfs-3g defaults,locale=en_US.UTF-8 0 0 #Entry for /dev/sdb1 : UUID=EA6854D268549F5F /media/WD ntfs-3g defaults,nosuid,nodev,locale=en_US.UTF-8 0 0 #Entry for /dev/sda6 : UUID=ed077c52-c50e-406c-9120-9cb6f86ec204 none swap sw 0 0 Here is my mtab /dev/sda5 / ext4 rw,errors=remount-ro,commit=0 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 fusectl /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 udev /dev devtmpfs rw,mode=0755 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 tmpfs /run tmpfs rw,noexec,nosuid,size=10%,mode=0755 0 0 none /run/lock tmpfs rw,noexec,nosuid,nodev,size=5242880 0 0 none /run/shm tmpfs rw,nosuid,nodev 0 0 /dev/sda3 /media/OS fuseblk rw,nosuid,nodev,allow_other,blksize=4096 0 0 /dev/sda2 /media/RECOVERY fuseblk rw,nosuid,nodev,allow_other,blksize=4096 0 0 /dev/sdb1 /media/WD fuseblk rw,nosuid,nodev,allow_other,blksize=4096 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,noexec,nosuid,nodev 0 0 gvfs-fuse-daemon /home/hanine/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,user=hanine 0 0 Appearently it cannot be mounted because upon login, it finds that it is already mounted. Some sort of conflict. Does anyone have a clue on how to solve this. Thanks.

  Read the article

• Automount of external hard disk

  - by moose

  I have an Intenso 6002560 1TB Memory Station - an external hard disk. This hard disk gets connected via Y-USB cable. When I connect both USB-ends to my Notebook, it gets recognized by my Ubuntu 10.04.4 LTS system: moose@pc07:~$ lsusb [...] Bus 002 Device 005: ID 13fd:1840 Initio Corporation [...] and Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065e10 Device Boot Start End Blocks Id System /dev/sda1 * 1 37810 303704064 83 Linux /dev/sda2 37810 38914 8864769 5 Extended /dev/sda5 37810 38914 8864768 82 Linux swap / Solaris Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0d6ea32a Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976759008+ c W95 FAT32 (LBA) But it did not get mounted: moose@pc07:/dev$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) However, I could mount it manually with mount -t vfat /dev/sdc1 /mnt/sdc1 as you can see here: moose@pc07:~$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) /dev/sdc1 on /mnt/sdc1 type vfat (rw) edit: Another command: moose@pc07:~$ sudo blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 moose@pc07:~$ blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 /dev/sdc1 /mnt/sdc1 edit: another command: moose@pc07:~$ ls -l /dev/disk/by-uuid/ total 0 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 45eb611b-517e-425b-8057-0391726cccd5 -> ../../sda1 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 e9dc42f3-594c-4b62-874a-305eda5eed41 -> ../../sda5 Here is a link to a Launchpad question about this problem. But I would like it to mount automatically. What do I have to do?

  Read the article

• Why Aren't Programs Written In Assembly More Often?

  - by mudge

  It seems to be a mainstream opinion that assembly programming takes longer and is more difficult to program in than a higher level language such as C. Therefore it seems to be recommend or assumed that it is better to write in a higher level language for these reasons and for the reason of better portability. Recently I've been writing in x86 assembly and it has dawned on me that perhaps these reasons are not really true, except perhaps portability. Perhaps it is more of a matter of familiarity and knowing how to write assembly well. I also noticed that programming in assembly is quite different than programming in an HLL. Perhaps a good and experienced assembly programmer could write programs just as easily and as quickly as an experienced C programmer writing in C. Perhaps it is because assembly programming is quite different than HLLs, and so requires different thinking, methods and ways, which makes it seem very awkward to program in for the unfamiliar, and so gives it its bad name for writing programs in. If portability isn't an issue, then really, what would C have over a good assembler such as NASM?

  Read the article

• assembly.GetTypes() does not return all types

  - by meta

  I try to lead the types from an .dll (which is also referenced in the executing project). I call: public static void LoadPlugin(string pluginFile) { Assembly assembly = Assembly.LoadFrom(pluginFile); foreach (Type type in assembly.GetTypes()) { // play with it } } It loads just a few of them: public partial class Mathematics : UserControl, IMathematics, IPortable and public partial class Welcome : UserControl but the next one, and some others, are ignored: public partial class Test : UserControl, ITest, IPortable They all stand in the same assembly, under the same namespace. The public static void LoadPlugin(string pluginFile) method is located in other assembly that is also referenced in the executing project. No exceptions are thrown. What could be the issues for not loading all the types? Any ideas?

  Read the article

• Updating Versioned .NET Assembly References

  - by ryrich

  I have a C++/CLI project that needs to reference a .NET assembly. I've done so by going into the project properties and clicking "Add New Reference", and browsing to the assembly location (it's not part of the solution, so I cannot create a project-to-project reference, and the .NET assembly is not in the GAC so it isn't in the .NET tab when viewing the references to add) When the .NET assembly is updated (that is, since it is versioned, it will increment its version number daily), the C++/CLI project fails to compile because it is still referencing the older version. The workaround I've been doing is deleting the .NET reference and adding it back in, but this is not feasible. How do I have it recognize the newer assembly?? Note: The older assembly is replaced with the newer one, so it is in the same location, but doesn't know that it should use the newer version.

  Read the article

• Use external display from boot on Samsung laptop

  - by OhMrBigshot

  I have a Samsung RV511 laptop, and recently my screen broke. I connected an external screen and it works fine, but only after Windows starts. I want to be able to use the external screen right from boot, in order to set the BIOS to boot from DVD, and to then install a different OS and also format the hard drive. Right now I can only use the screen when Windows loads. What I've tried: I've tried opening up the laptop and disconnecting the display to make it only find the external and use the VGA as default -- didn't work. I've tried using the Fn+key combo in BIOS to connect external display - nothing I've been looking around for ways to change boot sequence without entering BIOS, but it doesn't look like it's possible. Possible solutions? A way to change boot sequence without entering BIOS? Someone with the same brand/similar model to help me blindly keystroke the correct arrows/F5/F6 buttons while in BIOS mode to change boot sequence? A way to force the external display to work from boot, through modifying the internal connections (I have no problem taking the laptop apart if needed, please no soldering though), through BIOS or program? Also, if I change boot sequence without accessing external screen, would the Ubuntu 12.1 installation sequence attempt to use the external screen or would I only be able to use it after Linux is installed and running? I'd really appreciate help, I can't afford to fix the screen for a few months from now, and I'd really like to make my computer come back to decent performance! Thanks in advance!

  Read the article

• External HDD USB 3.0 failure

  - by Philip

  [ 2560.376113] usb 9-1: new high-speed USB device number 2 using xhci_hcd [ 2560.376186] usb 9-1: Device not responding to set address. [ 2560.580136] usb 9-1: Device not responding to set address. [ 2560.784104] usb 9-1: device not accepting address 2, error -71 [ 2560.840127] hub 9-0:1.0: unable to enumerate USB device on port 1 [ 2561.080182] usb 10-1: new SuperSpeed USB device number 5 using xhci_hcd [ 2566.096163] usb 10-1: device descriptor read/8, error -110 [ 2566.200096] usb 10-1: new SuperSpeed USB device number 5 using xhci_hcd [ 2571.216175] usb 10-1: device descriptor read/8, error -110 [ 2571.376138] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2571.744174] usb 10-1: new SuperSpeed USB device number 7 using xhci_hcd [ 2576.760116] usb 10-1: device descriptor read/8, error -110 [ 2576.864074] usb 10-1: new SuperSpeed USB device number 7 using xhci_hcd [ 2581.880153] usb 10-1: device descriptor read/8, error -110 [ 2582.040123] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2582.224139] hub 9-0:1.0: unable to enumerate USB device on port 1 [ 2582.464177] usb 10-1: new SuperSpeed USB device number 9 using xhci_hcd [ 2587.480122] usb 10-1: device descriptor read/8, error -110 [ 2587.584079] usb 10-1: new SuperSpeed USB device number 9 using xhci_hcd [ 2592.600150] usb 10-1: device descriptor read/8, error -110 [ 2592.760134] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2593.128175] usb 10-1: new SuperSpeed USB device number 11 using xhci_hcd [ 2598.144183] usb 10-1: device descriptor read/8, error -110 [ 2598.248109] usb 10-1: new SuperSpeed USB device number 11 using xhci_hcd [ 2603.264171] usb 10-1: device descriptor read/8, error -110 [ 2603.480157] usb 10-1: new SuperSpeed USB device number 12 using xhci_hcd [ 2608.496162] usb 10-1: device descriptor read/8, error -110 [ 2608.600091] usb 10-1: new SuperSpeed USB device number 12 using xhci_hcd [ 2613.616166] usb 10-1: device descriptor read/8, error -110 [ 2613.832170] usb 10-1: new SuperSpeed USB device number 13 using xhci_hcd [ 2618.848135] usb 10-1: device descriptor read/8, error -110 [ 2618.952079] usb 10-1: new SuperSpeed USB device number 13 using xhci_hcd [ 2623.968155] usb 10-1: device descriptor read/8, error -110 [ 2624.184176] usb 10-1: new SuperSpeed USB device number 14 using xhci_hcd [ 2629.200124] usb 10-1: device descriptor read/8, error -110 [ 2629.304075] usb 10-1: new SuperSpeed USB device number 14 using xhci_hcd [ 2634.320172] usb 10-1: device descriptor read/8, error -110 [ 2634.424135] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2634.776186] usb 10-1: new SuperSpeed USB device number 15 using xhci_hcd [ 2639.792105] usb 10-1: device descriptor read/8, error -110 [ 2639.896090] usb 10-1: new SuperSpeed USB device number 15 using xhci_hcd [ 2644.912172] usb 10-1: device descriptor read/8, error -110 [ 2645.128174] usb 10-1: new SuperSpeed USB device number 16 using xhci_hcd [ 2650.144160] usb 10-1: device descriptor read/8, error -110 [ 2650.248062] usb 10-1: new SuperSpeed USB device number 16 using xhci_hcd [ 2655.264120] usb 10-1: device descriptor read/8, error -110 [ 2655.480182] usb 10-1: new SuperSpeed USB device number 17 using xhci_hcd [ 2660.496121] usb 10-1: device descriptor read/8, error -110 [ 2660.600086] usb 10-1: new SuperSpeed USB device number 17 using xhci_hcd [ 2665.616167] usb 10-1: device descriptor read/8, error -110 [ 2665.832177] usb 10-1: new SuperSpeed USB device number 18 using xhci_hcd [ 2670.848110] usb 10-1: device descriptor read/8, error -110 [ 2670.952066] usb 10-1: new SuperSpeed USB device number 18 using xhci_hcd [ 2675.968081] usb 10-1: device descriptor read/8, error -110 [ 2676.072124] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2786.104531] xhci_hcd 0000:02:00.0: remove, state 4 [ 2786.104546] usb usb10: USB disconnect, device number 1 [ 2786.104686] xHCI xhci_drop_endpoint called for root hub [ 2786.104692] xHCI xhci_check_bandwidth called for root hub [ 2786.104942] xhci_hcd 0000:02:00.0: USB bus 10 deregistered [ 2786.105054] xhci_hcd 0000:02:00.0: remove, state 4 [ 2786.105065] usb usb9: USB disconnect, device number 1 [ 2786.105176] xHCI xhci_drop_endpoint called for root hub [ 2786.105181] xHCI xhci_check_bandwidth called for root hub [ 2786.109787] xhci_hcd 0000:02:00.0: USB bus 9 deregistered [ 2786.110134] xhci_hcd 0000:02:00.0: PCI INT A disabled [ 2794.268445] pci 0000:02:00.0: [1b73:1000] type 0 class 0x000c03 [ 2794.268483] pci 0000:02:00.0: reg 10: [mem 0x00000000-0x0000ffff] [ 2794.268689] pci 0000:02:00.0: PME# supported from D0 D3hot [ 2794.268700] pci 0000:02:00.0: PME# disabled [ 2794.276383] pci 0000:02:00.0: BAR 0: assigned [mem 0xd7800000-0xd780ffff] [ 2794.276398] pci 0000:02:00.0: BAR 0: set to [mem 0xd7800000-0xd780ffff] (PCI address [0xd7800000-0xd780ffff]) [ 2794.276419] pci 0000:02:00.0: no hotplug settings from platform [ 2794.276658] xhci_hcd 0000:02:00.0: enabling device (0000 -> 0002) [ 2794.276675] xhci_hcd 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 2794.276762] xhci_hcd 0000:02:00.0: setting latency timer to 64 [ 2794.276771] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 2794.276913] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9 [ 2794.395760] xhci_hcd 0000:02:00.0: irq 16, io mem 0xd7800000 [ 2794.396141] xHCI xhci_add_endpoint called for root hub [ 2794.396144] xHCI xhci_check_bandwidth called for root hub [ 2794.396195] hub 9-0:1.0: USB hub found [ 2794.396203] hub 9-0:1.0: 1 port detected [ 2794.396305] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 2794.396371] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 10 [ 2794.396496] xHCI xhci_add_endpoint called for root hub [ 2794.396499] xHCI xhci_check_bandwidth called for root hub [ 2794.396547] hub 10-0:1.0: USB hub found [ 2794.396553] hub 10-0:1.0: 1 port detected [ 2798.004084] usb 1-3: new high-speed USB device number 8 using ehci_hcd [ 2798.140824] scsi21 : usb-storage 1-3:1.0 [ 2820.176116] usb 1-3: reset high-speed USB device number 8 using ehci_hcd [ 2824.000526] scsi 21:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2824.002263] sd 21:0:0:0: Attached scsi generic sg2 type 0 [ 2824.003617] sd 21:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2824.005139] sd 21:0:0:0: [sdb] Write Protect is off [ 2824.005149] sd 21:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2824.009084] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.009094] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.011944] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.011952] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.049153] sdb: sdb1 [ 2824.051814] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.051821] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.051825] sd 21:0:0:0: [sdb] Attached SCSI disk [ 2839.536624] usb 1-3: USB disconnect, device number 8 [ 2844.620178] usb 10-1: new SuperSpeed USB device number 2 using xhci_hcd [ 2844.640281] scsi22 : usb-storage 10-1:1.0 [ 2850.326545] scsi 22:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2850.327560] sd 22:0:0:0: Attached scsi generic sg2 type 0 [ 2850.329561] sd 22:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2850.329889] sd 22:0:0:0: [sdb] Write Protect is off [ 2850.329897] sd 22:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2850.330223] sd 22:0:0:0: [sdb] No Caching mode page present [ 2850.330231] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.331414] sd 22:0:0:0: [sdb] No Caching mode page present [ 2850.331423] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.384116] usb 10-1: USB disconnect, device number 2 [ 2850.392050] sd 22:0:0:0: [sdb] Unhandled error code [ 2850.392056] sd 22:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2850.392061] sd 22:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 2850.392074] end_request: I/O error, dev sdb, sector 0 [ 2850.392079] quiet_error: 70 callbacks suppressed [ 2850.392082] Buffer I/O error on device sdb, logical block 0 [ 2850.392194] ldm_validate_partition_table(): Disk read failed. [ 2850.392271] Dev sdb: unable to read RDB block 0 [ 2850.392377] sdb: unable to read partition table [ 2850.392581] sd 22:0:0:0: [sdb] READ CAPACITY failed [ 2850.392584] sd 22:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2850.392588] sd 22:0:0:0: [sdb] Sense not available. [ 2850.392613] sd 22:0:0:0: [sdb] Asking for cache data failed [ 2850.392617] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.392621] sd 22:0:0:0: [sdb] Attached SCSI disk [ 2850.732182] usb 10-1: new SuperSpeed USB device number 3 using xhci_hcd [ 2850.752228] scsi23 : usb-storage 10-1:1.0 [ 2851.752709] scsi 23:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2851.754481] sd 23:0:0:0: Attached scsi generic sg2 type 0 [ 2851.756576] sd 23:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2851.758426] sd 23:0:0:0: [sdb] Write Protect is off [ 2851.758436] sd 23:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2851.758779] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.758787] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.759968] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.759977] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.817710] sdb: sdb1 [ 2851.820562] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.820568] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.820572] sd 23:0:0:0: [sdb] Attached SCSI disk [ 2852.060352] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.076533] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.076538] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.196329] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.212593] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.212599] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.456290] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.472402] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.472408] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.624304] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.640531] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.640536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.772296] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.788536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.788541] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.920349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.936536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.936540] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2853.072287] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2853.088565] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2853.088570] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.176339] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.192561] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.192567] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.320349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.336526] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.336531] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.468344] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.484551] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.484556] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.612349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.628540] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.628545] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.756350] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.772528] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.772533] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.848116] usb 10-1: USB disconnect, device number 3 [ 2884.851493] scsi 23:0:0:0: [sdb] killing request [ 2884.851501] scsi 23:0:0:0: [sdb] killing request [ 2884.851699] scsi 23:0:0:0: [sdb] Unhandled error code [ 2884.851702] scsi 23:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2884.851708] scsi 23:0:0:0: [sdb] CDB: Read(10): 28 00 00 5f 2b ee 00 00 3e 00 [ 2884.851721] end_request: I/O error, dev sdb, sector 6237166 [ 2884.851726] Buffer I/O error on device sdb1, logical block 6237102 [ 2884.851730] Buffer I/O error on device sdb1, logical block 6237103 [ 2884.851738] Buffer I/O error on device sdb1, logical block 6237104 [ 2884.851741] Buffer I/O error on device sdb1, logical block 6237105 [ 2884.851744] Buffer I/O error on device sdb1, logical block 6237106 [ 2884.851747] Buffer I/O error on device sdb1, logical block 6237107 [ 2884.851750] Buffer I/O error on device sdb1, logical block 6237108 [ 2884.851753] Buffer I/O error on device sdb1, logical block 6237109 [ 2884.851757] Buffer I/O error on device sdb1, logical block 6237110 [ 2884.851807] scsi 23:0:0:0: [sdb] Unhandled error code [ 2884.851810] scsi 23:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2884.851813] scsi 23:0:0:0: [sdb] CDB: Read(10): 28 00 00 5f 2c 2c 00 00 3e 00 [ 2884.851824] end_request: I/O error, dev sdb, sector 6237228 [ 2885.168190] usb 10-1: new SuperSpeed USB device number 4 using xhci_hcd [ 2885.188268] scsi24 : usb-storage 10-1:1.0 Please help me with my problem. I got this after running dmesg.

  Read the article

• Folder missing in external hard drive

  - by Hans

  I have been backing up my folders, I am using Seagate Expansion portable Drive. I had created a folder called "|o|o" in the root folder of the portable drive... I copied my latest folders into "|o|o" folder to re-install ubuntu. When I open the portable drive the folder |o|o is not visible, when I ctrl+a and check properties the space used is 122GB, however when I click on the drive to view properties of the drive used space is 260GB. It looks as if the folder is there in the portable drive but I cannot access it... I have tried to view all the hidden files and "|o|o" is still not there. I am using 12.04.Can you please help me to retrieve this folder.

  Read the article

• External Hard disk not workng on windows after I formatted it on Ubuntu

  - by nav_jan

  I formatted my Western Digital 500 Gb hard disk on Ubuntu 10.4 and now I want to use it on Windows 7 but it cannot detect it. I formatted it with FAT(applicable to all) option. I tried to Google this problem a bit and as suggested by one of the site i tried to format this drive with NTFS. Still windows cannot detect it. Drives in windows 7 is not a problem because I tried a different usb drive on it and it works. I can see the led of the drive glow when I connect it and I can also see remove drive safely option in lower right corner, but i cannot see any option in "my computer" to access the hard disk. I am new to Ubuntu. Any help is appreciated.

  Read the article

• Weird error running com-exposed assembly

  - by Bernabé Panarello

  I am facing the following issue when deploying a com-exposed assembly to my client's. The COM component should be consummed by a vb6 application. Here's how it's done 1) I have one c# project which has a class with a couple of methods exposed to COM 2) The project has references to multiple assemblies 3) I compile the project, generating a folder (named dllcom) that contains the assembly plus all the referenced dlls 4) I include in the folder a .bat which does the following: regasm /u c:\dllcom\LibInsertador.dll del LibInsertador.tlb regasm c:\dllcom\LibInsertador.dll /tlb:c:\dllcom\LibInsertador.tlb /codebase c:\dllcom\ pause 5) After running the bat locally in many workstations of my laboratory, i'm able to consume the generated tlb from my vb6 application without any problems. I'm even able to update the dll by only means of running this bat, without having to recompile the vb6 application. I mean that im not having issues of vb6 fiding and invoking the exposed com object. The problem 6) I send the SAME FOLDER to my client 7) They execute the .bat locally, without any errors 8) They execute the vb6 application, vb6 finds the main assembly, the .net code seems to run correctly (it's even able to generate a log file) until it has to intantiate it's first referenced assembly. Then, they get the following exception: "Could not load type 'GYF.Common.TypeBuilder' from assembly 'GYF_Common, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null'." Where "GYF.Common" is an assembly referenced by LibInsertador and TypeBuilder is a class contained in GYF.Common. GYF.Common is not a signed assembly and it's not in the GAC, just in the same folder with Libinsertador. According to .net reflector, the version is correct. ¿Any ideas about what could be happening?

  Read the article

• PowerShell - Set Alias for Loaded Assembly

  - by Uros Calakovic

  I use this code to load a .Net assembly to PowerShell: [System.Reflection.Assembly]::Load("System.Windows.Forms, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089") | out-null [System.Windows.Forms.MessageBox]::Show("Hello world") Can I set an alias for an assembly (for example 'System.Windows.Forms' = 'Forms') so that I don't have to type the assembly full name when calling static methods like MessageBox.Show()?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >