Search Results

Search found 2481 results on 100 pages for 'hp photosmart'.

Page 5/100 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • HP Network Utility Error

    - by William Ricci
    Using the HP Network Utility to team 2 ports on Windows 2008 R2 Standard results in this error:----- An error occurred when making a call into the operating system. Happens on either of two cards that are installed. This happened before and after upgrading to PSP 9.10. Uninstalled the HP Network Configuration Utility and re-installed version 10.65.0.6. Updated NIC drivers. NC382i DP - HP Broadcom 1Gb Multifunction Driver 7.4.23.0 (from 6.2.9.0) NC365T - Intel E1R 11.14.80.0 (from 11.14.49.0)

    Read the article

  • HP SmartArray P400 has slow read and write speed

    - by Tadas D.
    I have desktop in which I installed HP SmartArray P400 controller with two HP DF0146B8052 hard drives. I made RAID0 logical volume from them, but I am getting 20MB/s write speed and ~140-120MB/s read speed. Also there is quite low scatter for benchmark results (I am getting quite nice line) and it looks like controller is "capping" my speeds. I tried reseting controllers configuration and I haven't found any settings in HP ACU (Array Configuration Utility) to help me. I am using Windows 7 Ultimate and M4A78 board Does anyone have ideas what could be wrong? Also I am attaching diagnostic results.

    Read the article

  • Configuring RAID1 on HP Proliant Microserver N54L / Ubuntu 14.04.1 LTS [duplicate]

    - by Chris Beach
    This question already has an answer here: Cant find my harddrives in ubuntu installation? 2 answers I've bought a N54L and fitted two 3GB drives. Keen to get set up with RAID1. BIOS: SATA controller mode set to "RAID" RAID Option ROM utility: both physical drives set up as one logical drive When I came to install Ubuntu (14.04.1), both drives appeared during the setup process. I was only expecting to see the logical drive, although I'm a complete novice with RAID. I've read that the HP Proliant Microservers don't have "proper" RAID support, and require some kind of driver to be installed. I've tried a few HP utilities from the following apt repo: deb http://downloads.linux.hp.com/SDR/repo/mcp wheezy/current non-free On installation, most say "server not supported" Would appreciate your advice.

    Read the article

  • HP Recovery options: System Recovery not showing

    - by sha404
    I am using HP Pavilion dv4 notebook. Previously, there were following options in Recovery Manager(using f11 during boot): +System Recovery +Factory Restore +Minimized Image Recovery The System Recovery option allows me to restore only Operating system drive e.g. C:\ drive, keeping all other user (me) created hard drives intact. I made a set of recovery disk. Since then I don't see the System Recovery option in HP Recovery Manager. But all other options are still there. But when I use recovery disks that i created earlier, that option e.g. System Recovery is shown. But It's really boring and time consuming to use disks for recovery. So, what's the problem with internal HP Recovery Manager? Why isn't it showing that option?

    Read the article

  • Inverted function keys (F1-F12) on HP Pavilion dv4t

    - by The Electric Muffin
    (I know there have already been a lot of questions about this, but none of them mentioned the dv4t specifically.) I'm thinking about getting an HP Pavilion dv4t-4200 or -5100, but something that's really irritating me is that by default the function keys (F1-F12) are "inverted"—without holding the Fn key, the function keys do things like change the brightness, change or mute the volume, and switch to an external display. Only if you hold Fn will they actually produce F1, F2, etc. This is not how keyboards are supposed to work. Is there any way to disable this "feature" that has been verified to work on the HP Pavilion dv4t-4200 or HP Pavilion dv4t-5100? I don't want to buy this computer unless this is possible.

    Read the article

  • HP Omni 27-1027c AIO...Upgradeable?

    - by Bobo
    I just bought an HP Omni 27 1057c from Sams Club. I like it a lot, but I want more performance. discovered that the integrated Intel HD 2500 graphics is almost useless for most games. I found a website that says it can be upgraded at http://www.pcmag.com/article2/0,2817,2398314,00.asp. The computers specs can be found at Sams Club website or at HP website HP Product Specs. So what do you think? Can I upgrade Motherboard and Video Card?

    Read the article

  • Processor Upgrade HP Elite M9510F

    - by DaveM
    I have an HP 9510F that uses the ASUS IPIBL-LB MB. It ships with an Intel Q8200 Quad Core processor but it does not support virtualization. Specs for the board from HP (ASUS does not list this OEM board) do not show support for the Intel Q8200 it ships with (obviously incorrect) but only these • Supports the following processors: o Intel Core 2 Quad (Yorkfield core) Q9xxx o Intel Core 2 Duo (Wolfsdale core) E8xxx o Intel Core 2 Quad (Kentsfield core) up to Q6600 o Core 2 Duo E6x00 (Conroe core) up to E6700 o Core 2 Duo E4x00 (Conroe core) up to E4400 Can this MB support the Q8400 or will it only support the indicated Q9xxx series? Naturally HP is little help here. Specs are located hereHP/ASUS MB specs

    Read the article

  • Ctrl key is broken on HP Envy is broken, where can I find a replacement

    - by NewProger
    I work as a developer so I have to use key combinations a lot. And I have HP Envy laptop. And the Ctrl key is broken for the second time. First time I just took one from my friend. But I don't have any more friends who are willing to sacrifice their Ctrl key Anyone know where I can find one? (or rather a bunch because they are so weak and low quality) I tried to contact HP support but they did everything to prevent people from doing it. And it is impossible to reach HP support. And in my case where warranty is expired it is not possible at all according to their rules. Also I tried Googling but found nothing

    Read the article

  • My HP Laptop shows bios error

    - by Precious Tijesunimi
    Sometimes, when I startup my HP Laptop I get a message like this (I am not accurately sure of the message but it is something like this) HP Bios Startup error The selected bios file was not found. It is either corrupt or missing Please visit http://hp.com/go/techcenter/startup Please Press ENTER - to Continue. When I press enter nothing bad happens, My System Just starts up normally. I have had a similar problem with my desktop but whenever I press enter, The computer restarts and doesn't startup. I was told that a Virus had attacked my system. I am very worried. Is the same thing happening here?, How will it affect my system? and What can I do?

    Read the article

  • Printing documents on HP printer very slow

    - by maxim
    I have a strange problem with HP drivers. I have configured a HP printer 2025dn with LAN connection, on 3 pc, using the cd rom of HP driver. All works well, but sometimes for certain documents the time for printing is very slow and long. I observe during this situation, in task manager, a process called rundll32.exe loads CPU at 100%. If I kill that process the printer starts printing fast the document in the queue. I wondering the reason of this strange behaviour.

    Read the article

  • Why does HP Update at remote system trigger RDP printing at local system?

    - by lcbrevard
    This is obscure. When connected with RDP to another system that has HP Update installed on it, either directly running the HP Update or having the notification pop up to ask if you want to run HP Update causes the local system to try to print something to peculiarly-chosen-local-printer. Case 1: Desktop Win 7 Ult system RDP connected to HP Laptop Win 7 Ult system. When HP Update runs on the laptop a dialog for XPS Writer Save As... appears on Desktop system. Even if you put in a name, nothing gets generated and the dialog repeats. And repeats. Until you (a) close the RDP connection and (b) clean out the queued entries. If the HP Update pops up the request to run the update and you are not at the desk when this happens, there can be dozens of queued requests for this bogus printing. NOTE: the XPS Writer is not selected as a default printer on either system. Case 2: (Different) HP Laptop Win 7 Ult system RDP connected to XP Pro "brand X" desktop system but with HP printer drivers installed. If the request to run HP Update notification pops on the XP system, dozens of attempts to print, in this case to a Versa Check Printer driver, are queued. Dismissing the HP request, closing RDP, and cleaning out the queue are required to stop this. NOTE: the Versa Check Writer is not selected as a default printer on either system. THE QUESTION: What the heck is going on here? Some kind of scripting or COM activity that is misdirected?

    Read the article

  • HP Jetdirect 175x and HP Officejet K7103 printsharing

    - by Richard
    I have managed to get this setup working , but it is very unreliable and either the printserver or the printer seem to crash and wont respond after 1 or 2 prints, although I am able to still access the web config of the 175x. I had a similar problem with a linksys wireless print server with the same problem and assumed that a HP print server would do the job better...grrrr!! Anybody any ideas what to do next? It is not possible to flash the printserver, nor the printer as far as I know, so I assume I have some iffy settings in the print server config somewhre. All our users are W7 or Vista BTW. Cheers Richard

    Read the article

  • Generic socket 940 CPU fan for HP XW9300 interchangeable with HP part number 411454-001

    - by ConcernedOfTunbridgeWells
    Hi, I'm trying to find a generic Socket 940 CPU fan that will fit the air duct in an XW9300. Note that two different CPU fan mounting schemes have been used on this machine. One has two grommets in the motherboard that the CPU fan screws into and the other has a plastic collar and base plate. The form factor I'm looking for is the former (see the picture below). Two HP part numbers for fans in this form factor are 411454-001 (shown below) and 416055-001. Note that the dimensions are important as the machine has an air duct that fits over the fan. Can anyone tell me the manufacturer and model of an equivalent generic part? Better yet, do you know somewhere (preferrably in the UK) from which such an item can be obtained?

    Read the article

  • How do I turn on wireless adapter on HP Envy dv6 7200 under Ubuntu (any version)?

    - by Dave B.
    I have a new HP Envy dv6 7200 with dual boot Windows 8 / Ubuntu 12.04. In windows, the F12 key in Windows activates the "airplane mode" switch which enables/disables both on-board (mini PCIe) and USB wireless adapters. In Ubuntu, however, the wireless adapter is turned off by default and cannot be turned back on via the F12 key (or any other combination of F12 and Ctrl, Fn, Shift, etc.). Let me explain the "fixes" I've seen in various forums and explain what did or did not happen. These are listed in no particular order. (Spoiler alert: wireless is still broke). Solution 1? Use HP's "Wireless Assistant" utility to permanently activate the wireless card in Windows, then boot into Ubuntu to happily find it working. Unfortunately, this utility works in Windows 7 but not Windows 8. On the other hand, hardware drivers from HP are only available for Windows 8 for this model. Catch 22 (I could not find a comparable utility for Windows 8). Solution 2? Use a USB wireless adapter to sidestep the on-board device. I purchased such a device from thinkpenguin.com to be sure that it would be Linux-friendly. However, the wireless switch enables / disables all wireless devices including USB. So, there's my $50 donation to the nice folks at thinkpenguin.com, but still no solution. Solution 3? Following the Think Penguin folk's suggestion, modify the mini PCI express adapter following instructions here: http://www.notebookforums.com/t/225429/broken-wireless-hardware-switch-fix Tempting, but I then violate the terms of my warranty mere days after opening the box. This might be a good solution for an older machine that you want to get your geek on with, but not for a new box. Solution 4? rfkill unblock all No effect whatsoever. ubuntu@ubuntu-hp-evny:~$ rfkill unblock all ubuntu@ubuntu-hp-evny:~$ rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Solution 5? Re-install drivers. Done and done. Ubuntu recognizes the device - perhaps even without re-installing the drivers? - but cannot turn it on. How do I know this? In the Network Manager drop-down menu, the wireless option is blacked out and a message reads something like: "wireless network is disabled by a hardware switch". Solution 6? Identify a physical switch on the laptop and flip it. There is no such switch on this machine. In fact, walking through Best Buy yesterday, I checked and not a single new laptop PC had a physical switch on it. All of the wireless switches are either the F2 or F12 key ... I wonder if askubuntu will not be plagued by this exact issue in the near future? Additional info - lspci ubuntu@ubuntu-hp-evny:~$ lspci 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01) 0a:00.0 Network controller: Ralink corp. Device 539b 0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Any suggestions would be much appreciated!

    Read the article

  • Ubuntu + Raid on HP proliant DL 160 G6

    - by Adam Matan
    Hi, I'm, trying to install Ubuntu 8.04 Server on an HP Proliant DL160 G6. The HP hardware is certified by Ubuntu for the 9.04 version, which I can't install due to company policy. The problem is that Ubuntu would not recognize the RAID 1+0 disk configured by the BIOS. The raid creates one ~470GB disk from two 500GB physical disks. Any ideas? Adam

    Read the article

  • Proliant Support Pack and Ubuntu on older HP Proliants

    - by snl
    We have a couple of oldish HP Proliant servers -- one DL385 G1 and one DL360 G5, to be exact -- that we'd like to upgrade from CentOS 5 to Ubuntu LucidLynx. The problem is that HP doesn't offer Ubuntu Proliant Support Packs for these particular models. Would you upgrade regardless, skipping the PSPs altogether? Are there alternative hardware monitoring tools that would match the functionality of the PSPs? Is there a hack to install the PSP RPMs on an Ubuntu system?

    Read the article

  • HP blade server: How many connection can be made between HP new gen 8 blades and an interconnect

    - by Dave T
    I am building a virtualized network on an HP C3000 with 460c Gen 8 blades and 2 HP L3 switch interconnects. I was advised to by a 1Gb 4-port 366M Mezzanine Adapter. That provides me 6 ethernet connections to each blade. I have been told that you can only make 2 connections to from each blade to each interconnect, but since I have to interconnectes and 6 ports I hope someone can tell me if I can make 3 connections from each server to each interconnect. I looking for the actual - thanks Dave

    Read the article

  • HP Proliant Servers - WMI query for system health

    - by Mike McClelland
    Hi, I want to query lots of HP servers to determine their overall health. I don't want to use any packages, or even SNMP - I want to query the server health from WMI and understand if a box is Green/Amber/Red - just like the HP Management Home Page. This MUST be possible - but I can't find any documentation... Oh yes, and the servers are running Windows Server 2003/8. Help!! Mike

    Read the article

  • NDMP NAS for HP EVA4400 SAN

    - by Sergei
    We use EMC Celerra filer for our EMC array and it supports NDMP.n remote site we have EVA4400 HP SAN and it seems that our only option for NAS is Windows Storage Option. What if we want to use NDMP?Surely HP should have something that match Celerra?

    Read the article

  • No video output and no status light on HP Proliant Microserver

    - by tombull89
    I have an issue with a "N40L" HP Proliant Microserver. When the server is powered on the power light turns green but the machine's status light (the HP logo on the front) stays off and there is no video output through th onboard VGA. The system fan kicks in and if connected to a network the link light shows activity. I have no extra boards (iLO card, graphics card) only 4GB PNY non-standard stick of RAM.

    Read the article

  • HP P212 hangs on Initializing

    - by user927586
    I'm in trouble... Server: HP Microserver N36L Storage: HP P212/256 with BBWC Drives: 4 WD 2 Tb While expanding the RAID 5 array from 3 to 4 drives, the server rebooted itself. Expansion was at 76%. Now at boot the P212 seems to hang on initializing. After some time screen resets and the server boots, but in the os (Windows Server 2008R2) the P212 has errors (error code 10) and it's not seen by the HP ACU. Whats' going on? It's trying to complete the expansion? It's trying to make all over the expansion? It's simply stuck? What should I do? I NEED the data on the array! PS In the server BIOS, on the hd boot priority, the server still reports the array logical drive... maybe it's a good sign... PPS I'm not at the server physical location, so I cannot tell if the drives in the array are being accessed (that would be the case if the controller it's redoing/completing the expansion process) or not right now. Bye Dario

    Read the article

  • HP Pavillion DV6500 recovery disk failure

    - by Scott W
    I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >