Search Results

Search found 2690 results on 108 pages for 'ping pong'.

Page 5/108 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• VM load and ping problems after replacing server motherboard

  - by Andre

  Recently, we had to replace the motherboard of one of our servers. The procedure was done by IBM as it had guarantee. The server runs ESXi 5.1, with several virtual machines, including our main mail server (Domino) and a file server. After the replacing the motherboard and staring the VMs, ESXi asked us if we had moved it or copied (different motherboard is like a different computer). We clicked the latter. We started each machine and after some basic reconfiguration, all of them were up. However, we have been having problems with the mail server, it has been acting really slow at times (this could be when it syncs with the secondary mail server) and we have been checking with Centreon (a Nagios frontend) that its CPU load has been a bit high at times and ping response too. There was a moment this morning in which I tried connecting via SSH console and it was really slow to show login and basic commands like ifconfig and top. This particular mail server is a CentOS 4.4.7 64-bit. The little configuring we had to do after restarting it was to configure the network connection as it was resolving through DHCP. Our mail software is Lotus Notes server 9. Do you know of any way in which this replacement may be causing these difficulties, and how to fix it? Thanks.

  Read the article

• Can ping device from one computer and not the other

  - by Sean Duggan

  I've recently been assigned to work on a diagnostic program done in C++ which communicates with a piece of electronic equipment. Our normal scenario involves communicating via an RS232 interface, but I've been asked to make our program work over ethernet, source code having been done in Visual Basic. After much thrashing about trying to get the code to work and continuing to get 10049 Winsock errors when I tried to connect, I tried pinging the switch. From the computer the VB program is running on, I can see the switch via ping, nslookup, tracert, and pathping (I was going down the list of programs) and I can do this via URI or IP address. From my laptop, sending the same commands fails every time. They're both using the same network cable and the same USB-to-Ethernet device (I've been swapping them between tests) but one can see the switch and the other cannot. I'm working on the programming end, but the ping results makes me think that there might be a network issue stymieing me. wry grin I'm not much of a network guy, so I'm appealing to expert assistance. Both computers are running Windows XP if that helps. The connection is to an "IP-RS8" device which then connects to our VCU-C units. Each unit is accessible via URI or IP address on the desktop computer we usually have connected to the units (it's running the older VB program that I was asked to lift the networking code from). The connection is made via a USB-to-Ethernet adapter so as to leave the regular Ethernet port available for connecting to the company network. Hmm... come to think of it, I've probably been confusing the issue, talking about pinging "the switch" rather than indicating that it's the devices. My apologies. Communication is generally done with a DLL that uses Winsock functions to make queries for data from the VCU and then to receive. I'm failing when connecting. I haven't found anything on the firewall which should block these commands, but I'll keep poking. I don't know if it's potentially relevant, but on the desktop, the adapter maps to Local Area Connection 3 while on the laptop, it consistently maps to Local Area Connection 2. Currently reading up on DHCP. IPConfig /all results: Desktop Host Name . . . . . . . . . . . . : AMERDAEXXXXXX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Broadcom NetXtreme XYxx Gigabit Controller Physical Address. . . . . . . . . : YY-XX-YB-XX-XX-XX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XXX Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XY:XX:XX AM Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX axYYYYX USBX.Y to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XY.Y.Y.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XY.Y.Y.X DHCP Server . . . . . . . . . . . : XY.Y.Y.XY DNS Servers . . . . . . . . . . . : XY.Y.Y.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XY AM Lease Expires . . . . . . . . . . : Tuesday, August YX, XYXX XX:XY:XY AM Laptop Windows IP Configuration Host Name . . . . . . . . . . . . : AMERLAFYYXXYX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Intel(R) 82567LM Gigabit Network Connection Physical Address. . . . . . . . . : YY-XY-BY-DY-XB-YX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XY Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XX:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XX:XX:XX AM Ethernet adapter {XYXAAYXX-YEDY-XXYX-YYEX-BYXYXXYEEYEX}: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Nortel IPSECSHM Adapter - Packet Scheduler iniport Physical Address. . . . . . . . . : XX-XX-XX-XX-XX-YY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : Y.Y.Y.Y Subnet Mask . . . . . . . . . . . : Y.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Leaf Networks Adapter: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Leaf Networks Adapter Physical Address. . . . . . . . . : YY-FF-FA-BC-YF-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : X.XYY.XY.XX Subnet Mask . . . . . . . . . . . : XXX.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : YY-FX-AX-YA-BY-CA Ethernet adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Intel(R) WiFi Link 5300 AGN Physical Address. . . . . . . . . : YY-XX-YA-CX-FC-YE Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX ax88772 USB2.0 to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : XYX.XYY.X.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXX.Y Default Gateway . . . . . . . . . :

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system?

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system? [migrated]

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• Can't ping my computer - "Transmit failed. General failure."

  - by Vaccano

  I am having an issue with my computer. My IIS services are not working. I have narrowed it down to the fact that my computer cannot find itself via its name. I try pinging my computer by its name and I get this: C:\Users\18773ping MyComputerNameHere Pinging MyComputerNameHere [::1] with 32 bytes of data: PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. Ping statistics for ::1: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), I tried having someone else ping my machine and it works fine for them. Any ideas?

  Read the article

• Problem with ping/DNS

  - by bublegumm

  When I am pinging non-existing host like 'zzz' or 'qwerty' I am getting the following result Pinging zzz.kanisa.com [209.62.20.200] with 32 bytes of data: Reply from 209.62.20.200: bytes=32 time=60ms TTL=46 Reply from 209.62.20.200: bytes=32 time=66ms TTL=46 It looks like a virus to me. But I was unable to find a solution on web. Any ideas how to fix it?

  Read the article

• Make 2 virtual machines ping in virtual box

  - by darkheir

  I'm trying to make 2 virtual machines communicate in Virtual Box, but whitout any success. Here are the step I have done: I setted both VMs in Internal networking mode (using VBoxManage modifyvm "VM name" --nic<x> intnet) I setted the DHCP server that is built into VirtualBox to manage IP addresses :VBoxManage dhcpserver add --netname intnet --ip 10.13.13.100 --netmask 255.255.255.0 --lowerip 10.13.13.101 --upperip 10.13.13.254 --enable But then both of the VM have the same IP Adresse (10.13.13.101) and even if set the IP manually, the Virtual Machines are not pinging each other.

  Read the article

• Weirdly high ping on direct ethernet connection?

  - by Antriel

  I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms. I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms. I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN). Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't help. I tested it in the safe mode with networking, same problem there. It slows down our client-server based programs and I have no idea what's causing it. All I could google up was that disabling Interrupt Moderation would help, it didn't though. Anyone had similar problems? tl;nr: Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.

  Read the article

• ping: unknown host google.com

  - by Tar

  Relevant output: /etc/hosts 127.0.0.1 localhost localhost.localdomain localhost4 localhost4.localdomain4 ::1 localhost localhost.localdomain localhost6 localhost6.localdomain6 servers_ip_address server.2006scape.com server /etc/resolv.conf search 2006scape.com #Generated by NetworkManager nameserver 8.8.8.8 nameserver 8.8.4.4 Some stuff from tcpdump 07:46:28.795843 IP server_ip.42841 > 8.8.4.4.domain: 60253+ PTR? 87.127.104.87.in-addr.arpa. (44) 07:46:28.795980 IP server_ip.54001 > 8.8.4.4.domain: 7390+ PTR? 60.187.80.98.in-addr.arpa. (43) 07:46:28.804029 IP server_ip.59667 > 8.8.4.4.domain: 58876+ PTR? 134.154.161.72.in-addr.arpa. (45) 07:46:28.884171 IP server_ip.46255 > 8.8.4.4.domain: 63027+ PTR? 195.156.251.84.in-addr.arpa. (45) 07:46:28.884217 IP server_ip.35426 > 8.8.4.4.domain: 10538+ PTR? 118.3.182.166.in-addr.arpa. (44) 07:46:28.884253 IP server_ip.53635 > 8.8.4.4.domain: 29928+ PTR? 230.94.81.83.in-addr.arpa. (43) 07:46:28.884286 IP server_ip.45787 > 8.8.4.4.domain: 41151+ PTR? 18.32.223.121.in-addr.arpa. (44) 07:46:28.946045 IP server_ip.47246 > 8.8.4.4.domain: 43103+ PTR? 81.70.251.84.in-addr.arpa. (43) 07:46:28.946066 IP server_ip.33208 > 8.8.4.4.domain: 61117+ PTR? 69.170.184.71.in-addr.arpa. (44) Anyone have any input as to what is causing this?

  Read the article

• What to do if people can't ping me?

  - by slayerIQ

  Today, I installed my new router so I can connect my other pc and my ps3. In my network, there are some other computers these are connected with each other through another router. So I have one modem with 2 routers that make up my network. Everything works fine the only problem I am having is being pinged by other computers in the network. All the computers are on the same subnet 255.255.255.0. There is no problem with my firewall or anything I tested everything. How can I solve this?

  Read the article

• Can ping cannot be pinged

  - by slayerIQ

  Today, I installed my new router so I can connect my other pc and my ps3. In my network, there are some other computers these are connected with each other through another router. So I have one modem with 2 routers that make up my network. Everything works fine the only problem I am having is being pinged by other computers in the network. All the computers are on the same subnet 255.255.255.0. There is no problem with my firewall or anything I tested everything. How can i solve this?

  Read the article

• What all is there to know about ping while troubleshooting an internet connection?

  - by tMJ

  What all is there to know about ping and the IP address to ping while troubleshooting/diagnosing a problem in the internet connection? For example: I run the command ping 192.168.1.1 -t in the command prompt, and if there is no reply I get something is odd, but I don't understand what is and where it is. I am looking for a complete list (okay, as many as you got), of IP address to ping while troubleshooting my network connection, and an insight into what the status message returned by them implies.

  Read the article

• Does just-ping determine a website's accessibility and/or speed?

  - by Yves

  While looking for a webhost I wanted one that had good connectivity around the world, and ran their (shared hosting) test IPs on just-ping.com. This is a part of a sample result: München, Germany: Packets lost (10%) 24.8 24.9 25.1 178.xx.xx.xxx Cologne, Germany: Okay 5.6 5.7 5.8 178.xx.xx.xxx New York, U.S.A.: Packets lost (30%) 80.3 80.4 80.7 178.xx.xx.xxx Stockholm, Sweden: Packets lost (100%) 178.xx.xx.xxx Santa Clara, U.S.A.: Packets lost (30%) 158.1 158.4 158.7 178.xx.xx.xxx Vancouver, Canada: Packets lost (70%) 189.4 189.5 189.5 178.xx.xx.xxx London, United Kingdom: Packets lost (100%) Am I correct in thinking that hosts with several "Packets lost" messages from different locations have less stable or slower connections than hosts with all "Okays"?

  Read the article

• Cannot ping static ip on eth1

  - by Calvin Froedge

  I am trying to ping the network interface I have set up for eth1. This is my config: auto eth1 iface eth1 inet static address 192.168.1.2 netmask 255.255.255.0 gateway 192.168.1.1 broadcast 192.168.1.255 If I ping 192.168.1.2, I get: Ping 192.168.1.2 (192.168.1.2) 56(84) bytes of data. From 192.168.1.3 icmp_seq=3 Destination Host Unreachable Results of ifconfig tell me that the IPv4 address is 192.168.1.3. I can ping this ip. Bcast and Mask are as expected (same as in definition). I can ping 192.168.1.3 from my macbook. I cannot ping 192.168.1.2 locally or from my macbook. Any ideas why?

  Read the article

• Android Service - Ping URL

  - by Chris

  How can I use Android Service to do a ping callback? I need to open a webpage on a button click, but in the background, go ping another url for stats collection. Code snippets will be greatly helpful Thanks Chris

  Read the article

• TraceRoute and Ping in C#

  - by NET789

  Does anyone have C# code handy for doing a ping and traceroute to a target computer? I am looking for a pure code solution, not what I'm doing now, which is invoking the ping.exe and tracert.exe program and parsing the output. I would like something more robust.

  Read the article

• Implementing ICMP ping in Go

  - by marketer

  Is it possible to implement an ICMP ping in Go? The alternative is to fork a 'ping' process, but I'd rather write it in Go.

  Read the article

• How do I use the Firefox ping attribute?

  - by Nissan Fan

  Firefox apparently supports a PING attribute for HREFs. How do I implement code to receive the ping?

  Read the article

• Cannot ping ubuntu server by hostname - can only ping by IP

  - by Tone

  I have an unbuntu 9.10 server and have set the hostname to "fileserver" When I try to ping fileserver from a client machine it doesn't find it, however I can ping by the IP my router assigns it. I have tried changing the ip in /etc/hosts from this: 127.0.0.1 fileserver to this: 192.168.1.109 fileserver which is the ip being assigned. I had a previous install of this server and i had no issues with this - only difference in this install is i did not select any of the options such as LAMP, OpenSSH, etc during the install process. I can access the machine fine by ip using PuTTY. Any ideas?

  Read the article

• Can't ping guest OS from Windows XP SP3 host running VIC.

  - by Vittal

  Hi, I am running VMware ESX Server 3i Version 3.5.0 and accessing this server using VMware Infrastructure Client Version 2.5.0 on a Windows XP SP3 machine. I have enabled the Microsoft TCP/IP version 6 stack and assigned an IPv6 address (using the netsh command) to the network adapter. The guest OS'es running on ESX Server (includes Win7, W2K8, WinXP) also have IPv6 addresses enabled on their adapters. The adapters are configured to be in VM Network (Bridged mode) and hence have connectivity to the Internet. The VMs are able to ping each other using IPv6 addresses and are also able to ping a physical Win7 machine using IPv6 addresses. However, the Windows XP SP3 machine on which the Client is running is not able to ping any hosts running on ESX Server while the VMs are able to ping this host. Whenever I try to ping from WXP box I get the "Invalid source route specified." error. The WinXP machine is not able to ping the Win7 physical machine too (the same error as above is thrown). Can someone help me understand why I am receiving this error and what I need to do to resolve this error? Thanks, Vittal

  Read the article

• Changing balls direction in Pong

  - by hustlerinc

  I'm making a Pong game to get started with game-developement but I've run into a problem that i can't figure out. When trying to change the balls direction it doesn't change. This is the relevant code: function moveBall(){ this.speed = 2.5; this.direction = 2; if(this.direction == 1){ ball.X +=this.speed; } else if(this.direction == 2){ ball.X -=this.speed; } } function collision(){ if(ball.X == 500){ moveBall.direction = 2; } if(ball.X == 300){ moveBall.direction = 1; } } Why doesn't it work? I've tried many different ways, and none of them seem to work. The moveBall.direction changes though, since it alerts the new direction once it reaches the defined ball.X position. If someone could help me I would deeply appreciate it. I've included a JSFiddle link. http://jsfiddle.net/hustlerinc/y4wp3/

  Read the article

• High CPU usage on Pong clone

  - by max

  I just made my first game, a clone of Pong, using OpenGL and C++. But its using ~50% of the CPU, which I guess is very high for a game like this. How can I improve that? Can you please look up my code and tell me what all things I am doing wrong? Any feedback is welcome. http://pastebin.com/L5zE3axh Also it would be extremely helpful if you give some general points on how to develop games in OpenGL efficiently.. Thanks in advance!

  Read the article

• A can ping B, B can ping C but A cant ping C. How do i connect A to C (ethernet)?

  - by user16654

  I have a computer at home with ip 192.168.221.xxx I have another computer at work that I can ping and it has 2 ip addresses: 192.168.1.xxx and 192.168.0.xxx. Those last 2 addresses have the same gateway ie 192.168.1.1 . The computer at work is connected to a hub. That hub also has an embedded device connected to it with address 192.168.0.xxx Now from my home computer I cannot ping this embedded device. How would I connect to it without changing the subnetwork it connects to? I can ping the embedded device from my work computer and I can ping the work computer from my home computer. So I am trying to connect to the embedded device from my home computer through my work computer. Port forwarding? how would I establish that on Ubuntu?

  Read the article

• Html 5 ping pong game side collision problem

  - by Gurjit

  I am making a simple ping pong game where I am facing a side collision problem means when the ball collides with the either side of the paddle . Although I have written code for making it works but something is failing....I want plz someone to give suggestions and tell how to avoid it. Means while trying to hit the ball with side face of the paddle poses a problem.!! Here is the main part of the code causing problem function checkCollision(){ ///// This is collision detection for the upper part ///// if( cy + radius >= paddleTop && cx + radius > paddleLeft && cy + radius >= paddleTop + 5 && cx - radius <= paddleLeft + paddleWidth ) { dy = -dy; ++hits; /// On collision we are increasing the Score playSound(); } else if( cy + radius >= paddleTop && cy + radius <= paddleTop + paddleHeight && cx + radius >= paddleLeft && cy - radius <= paddleLeft - (radius + 1) ) { dx = -dx; } } here is working fiddle for it :- http://jsfiddle.net/gurjitmehta/orzpzf69/

  Read the article

• Cannot ping router with a static IP assigned?

  - by Uriah

  Alright. I am running Ubuntu LTS 12.04 and am trying to configure a local caching/master DNS server so I am using Bind9. First, here are some things via default DHCP: /etc/network/interfaces cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The primary network interface - STATIC #auto eth0 #iface eth0 inet static # address 192.168.2.113 # netmask 255.255.255.0 # network 192.168.2.0 # broadcast 192.168.2.255 # gateway 192.168.2.1 # dns-search uclemmer.net # dns-nameservers 192.168.2.113 8.8.8.8 /etc/resolv.conf cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 192.168.2.1 search uclemmer.net ifconfig ifconfig eth0 Link encap:Ethernet HWaddr 00:14:2a:82:d4:9e inet addr:192.168.2.103 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::214:2aff:fe82:d49e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1067 errors:0 dropped:0 overruns:0 frame:0 TX packets:2504 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:153833 (153.8 KB) TX bytes:214129 (214.1 KB) Interrupt:23 Base address:0x8800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:915 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:71643 (71.6 KB) TX bytes:71643 (71.6 KB) ping ping -c 4 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. 64 bytes from 192.168.2.1: icmp_req=1 ttl=64 time=0.368 ms 64 bytes from 192.168.2.1: icmp_req=2 ttl=64 time=0.224 ms 64 bytes from 192.168.2.1: icmp_req=3 ttl=64 time=0.216 ms 64 bytes from 192.168.2.1: icmp_req=4 ttl=64 time=0.237 ms --- 192.168.2.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.216/0.261/0.368/0.063 ms ping -c 4 google.com PING google.com (74.125.134.102) 56(84) bytes of data. 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=1 ttl=48 time=15.1 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=2 ttl=48 time=11.4 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=3 ttl=48 time=11.6 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=4 ttl=48 time=11.5 ms --- google.com ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 11.488/12.465/15.118/1.537 ms ip route ip route default via 192.168.2.1 dev eth0 metric 100 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.103 As you can see, with DHCP everything seems to work fine. Now, here are things with static IP: /etc/network/interfaces cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # The primary network interface - STATIC auto eth0 iface eth0 inet static address 192.168.2.113 netmask 255.255.255.0 network 192.168.2.0 broadcast 192.168.2.255 gateway 192.168.2.1 dns-search uclemmer.net dns-nameservers 192.168.2.1 8.8.8.8 I have tried dns-nameservers in various combos of *.2.1, *.2.113, and other reliable, public nameservers. /etc/resolv.conf cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 192.168.2.1 nameserver 8.8.8.8 search uclemmer.net Obviously, when I change the nameservers in the /etc/network/interfaces file, the nameservers change here too. ifconfig ifconfig eth0 Link encap:Ethernet HWaddr 00:14:2a:82:d4:9e inet addr:192.168.2.113 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::214:2aff:fe82:d49e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1707 errors:0 dropped:0 overruns:0 frame:0 TX packets:2906 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:226230 (226.2 KB) TX bytes:263497 (263.4 KB) Interrupt:23 Base address:0x8800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:985 errors:0 dropped:0 overruns:0 frame:0 TX packets:985 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:78625 (78.6 KB) TX bytes:78625 (78.6 KB) ping ping -c 4 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. --- 192.168.2.1 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms ping -c 4 google.com ping: unknown host google.com Lastly, here are my bind zone files: /etc/bind/named.conf.options cat /etc/bind/named.conf.options options { directory "/etc/bind"; // // // query-source address * port 53; notify-source * port 53; transfer-source * port 53; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; forwarders { // My local 192.168.2.113; // Comcast 75.75.75.75; 75.75.76.76; // Google 8.8.8.8; 8.8.4.4; // DNSAdvantage 156.154.70.1; 156.154.71.1; // OpenDNS 208.67.222.222; 208.67.220.220; // Norton 198.153.192.1; 198.153.194.1; // Verizon 4.2.2.1; 4.2.2.2; 4.2.2.3; 4.2.2.4; 4.2.2.5; 4.2.2.6; // Scrubit 67.138.54.100; 207.255.209.66; }; // // // //allow-query { localhost; 192.168.2.0/24; }; //allow-transfer { localhost; 192.168.2.113; }; //also-notify { 192.168.2.113; }; //allow-recursion { localhost; 192.168.2.0/24; }; //======================================================================== // If BIND logs error messages about the root key being expired, // you will need to update your keys. See https://www.isc.org/bind-keys //======================================================================== dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.local cat /etc/bind/named.conf.local // // Do any local configuration here // // Consider adding the 1918 zones here, if they are not used in your // organization //include "/etc/bind/zones.rfc1918"; zone "example.com" { type master; file "/etc/bind/zones/db.example.com"; }; zone "2.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/db.2.168.192.in-addr.arpa"; /etc/bind/zones/db.example.com cat /etc/bind/zones/db.example.com ; ; BIND data file for example.com interface ; $TTL 604800 @ IN SOA yossarian.example.com. root.example.com. ( 1343171970 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS yossarian.example.com. @ IN A 192.168.2.113 @ IN AAAA ::1 @ IN MX 10 yossarian.example.com. ; yossarian IN A 192.168.2.113 router IN A 192.168.2.1 printer IN A 192.168.2.200 ; ns01 IN CNAME yossarian.example.com. www IN CNAME yossarian.example.com. ftp IN CNAME yossarian.example.com. ldap IN CNAME yossarian.example.com. mail IN CNAME yossarian.example.com. /etc/bind/zones/db.2.168.192.in-addr.arpa cat /etc/bind/zones/db.2.168.192.in-addr.arpa ; ; BIND reverse data file for 2.168.192.in-addr interface ; $TTL 604800 @ IN SOA yossarian.example.com. root.example.com. ( 1343171970 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS yossarian.example.com. @ IN A 255.255.255.0 ; 113 IN PTR yossarian.example.com. 1 IN PTR router.example.com. 200 IN PTR printer.example.com. ip route ip route default via 192.168.2.1 dev eth0 metric 100 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.113 I can SSH in to the machine locally at *.2.113 or at whatever address is dynamically assigned when in DHCP "mode". *2.113 is in my router's range and I have ports open and forwarding to the server. Pinging is enabled on the router too. I briefly had a static configuration working but it died after the first reboot. Please let me know what other info you might need. I am beyond frustrated/baffled.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >