Search Results

Search found 1864 results on 75 pages for 'raid 5'.

Page 5/75 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • mkfs Operation Takes Very Long on Linux Software Raid 5

    - by Elmar Weber
    I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

    Read the article

  • How to re-add RAID-10 dropped drive?

    - by thiesdiggity
    I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

    Read the article

  • How to restruct RAID 10?

    - by user276851
    We would like to alter the partition without losing data. Here is the sketch of the plan. I am wondering if it is doable using mdadm; and if so, please kindly point some reference on how to carry out the following steps. For RAID 10, there are four disks used. (1 2)(3 4) The idea is to work on 1 and 3 while keeping 2 and 4 as backup. 1: break RAID 10 into two arrays of RAID 0 => (1 3) (2 4) (how to?) 2: re-partition and format (1 3) 3: copy data from (2 4) to (1 3) 4: re-partition and format (2 4) exactly as (1 3) 5: join (2 4) with (1 3) to form RAID 10 (how to?) Does it sound doable? Thanks a lot! Add: It looks like this guy (drumfile) is doing something similar, but lack of enough detail.

    Read the article

  • Unneeded RAID recovery

    - by Shinhan
    I have two software RAID 5s. Today when I turned on my server (after it was off for two weeks when I was on vacation), I got the message that the software RAID is degraded and was offered RAID recovery console or boot degraded. No idea what to do in that recovery console btw, so I just exited it. After the boot finished normally I took a peak at /proc/mdstat but there is nothing amiss there. So I took a look at mdadm --detail /dev/md0 (and md1) and again everything looks fine with Failed Devices being 0 both times. Next I took a look at smartctl --alll /dev/sdX for all of the drives and Reallocated_Sector_Ct is 0. (Lots of other zeros, all numbers look to me fine) Anybody have any ideas why I'm getting the RAID recovery message on boot when nothing seems bad?

    Read the article

  • hardware raid0 to software raid0

    - by Frankie
    Does anyone know if it's possible to switch from a hardware based RAID0 to a software one? Have a broken raid controller (vintage, wont find it anywhere) but I know the Array is in good conditions. Has anyone tried this, and/or know if its possible? Thank you for your time.

    Read the article

  • How do I stop and repair a RAID 5 array that has failed and has I/O pending?

    - by Ben Hymers
    The short version: I have a failed RAID 5 array which has a bunch of processes hung waiting on I/O operations on it; how can I recover from this? The long version: Yesterday I noticed Samba access was being very sporadic; accessing the server's shares from Windows would randomly lock up explorer completely after clicking on one or two directories. I assumed it was Windows being a pain and left it. Today the problem is the same, so I did a little digging; the first thing I noticed was that running ps aux | grep smbd gives a lot of lines like this: ben 969 0.0 0.2 96088 4128 ? D 18:21 0:00 smbd -F root 1708 0.0 0.2 93468 4748 ? Ss 18:44 0:00 smbd -F root 1711 0.0 0.0 93468 1364 ? S 18:44 0:00 smbd -F ben 3148 0.0 0.2 96052 4160 ? D Mar07 0:00 smbd -F ... There are a lot of processes stuck in the "D" state. Running ps aux | grep " D" shows up some other processes including my nightly backup script, all of which need to access the volume mounted on my RAID array at some point. After some googling, I found that it might be down to the RAID array failing, so I checked /proc/mdstat, which shows this: ben@jack:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdb1[3](F) sdc1[1] sdd1[2] 2930271872 blocks level 5, 64k chunk, algorithm 2 [3/2] [_UU] unused devices: <none> And running mdadm --detail /dev/md0 gives this: ben@jack:~$ sudo mdadm --detail /dev/md0 /dev/md0: Version : 00.90 Creation Time : Sat Oct 31 20:53:10 2009 Raid Level : raid5 Array Size : 2930271872 (2794.53 GiB 3000.60 GB) Used Dev Size : 1465135936 (1397.26 GiB 1500.30 GB) Raid Devices : 3 Total Devices : 3 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Mon Mar 7 03:06:35 2011 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 1 Spare Devices : 0 Layout : left-symmetric Chunk Size : 64K UUID : f114711a:c770de54:c8276759:b34deaa0 Events : 0.208245 Number Major Minor RaidDevice State 3 8 17 0 faulty spare rebuilding /dev/sdb1 1 8 33 1 active sync /dev/sdc1 2 8 49 2 active sync /dev/sdd1 I believe this says that sdb1 has failed, and so the array is running with two drives out of three 'up'. Some advice I found said to check /var/log/messages for notices of failures, and sure enough there are plenty: ben@jack:~$ grep sdb /var/log/messages ... Mar 7 03:06:35 jack kernel: [4525155.384937] md/raid:md0: read error NOT corrected!! (sector 400644912 on sdb1). Mar 7 03:06:35 jack kernel: [4525155.389686] md/raid:md0: read error not correctable (sector 400644920 on sdb1). Mar 7 03:06:35 jack kernel: [4525155.389686] md/raid:md0: read error not correctable (sector 400644928 on sdb1). Mar 7 03:06:35 jack kernel: [4525155.389688] md/raid:md0: read error not correctable (sector 400644936 on sdb1). Mar 7 03:06:56 jack kernel: [4525176.231603] sd 0:0:1:0: [sdb] Unhandled sense code Mar 7 03:06:56 jack kernel: [4525176.231605] sd 0:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Mar 7 03:06:56 jack kernel: [4525176.231608] sd 0:0:1:0: [sdb] Sense Key : Medium Error [current] [descriptor] Mar 7 03:06:56 jack kernel: [4525176.231623] sd 0:0:1:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed Mar 7 03:06:56 jack kernel: [4525176.231627] sd 0:0:1:0: [sdb] CDB: Read(10): 28 00 17 e1 5f bf 00 01 00 00 To me it is clear that device sdb has failed, and I need to stop the array, shutdown, replace it, reboot, then repair the array, bring it back up and mount the filesystem. I cannot hot-swap a replacement drive in, and don't want to leave the array running in a degraded state. I believe I am supposed to unmount the filesystem before stopping the array, but that is failing, and that is where I'm stuck now: ben@jack:~$ sudo umount /storage umount: /storage: device is busy. (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1)) It is indeed busy; there are some 30 or 40 processes waiting on I/O. What should I do? Should I kill all these processes and try again? Is that a wise move when they are 'uninterruptable'? What would happen if I tried to reboot? Please let me know what you think I should do. And please ask if you need any extra information to diagnose the problem or to help!

    Read the article

  • Raid on ICH9R chip set

    - by user500982
    Hi Im looking at buyign this MB: http://www.supermicro.com/products/motherboard/ATOM/ICH9/X7SPE-HF-D525.cfm Im wondering though if the chipset will support the raid configuration I need. Im looking to configure the following arrays: raid array 1: 2 2TB Disks in Raid 0 raid array 2: 2 2TB Disks in Raid 0 raid array 3 (not actualy an array): 1 300GB Disk not in raid, to be used for OS and boot. So in total there would be 5 drives and the board supports 6. so im good when it comes to connections. However I have herd some chip sets only support one raid array (volume). so either all drives are individual, or are in the array. I must have 2 sperate raid arrays independent of each other, and a 5th drive not in any array. Anybody know if this setup will work? Thanks, -Stewart

    Read the article

  • Restoring GRUB2 on Software RAID 0 after Windows 7 wiped it using Ubuntu 10.10 LiveCD

    - by unknownthreat
    I have installed Ubuntu 10.10 on my system. However, I need to install Windows 7 back, and I expect that it would alter GRUB and it did. Right now, my partition on my Software RAID 0 looks like this: nvidia_acajefec1 is Ubuntu 10.10 and nvidia_acajefec3 is Windows 7. I've been following some guides around and I am always stuck at GRUB not able to detect the usual RAID content. I've tried running: sudo grub > root (hd0,0) GRUB complains it couldn't find my hard disk. So I tried: find (hd0,0) And it complains that it couldn't find anything. So I tried: find /boot/grub/stage1 It said "file not found". Here's the text from the console: ubuntu@ubuntu:~$ grub Probing devices to guess BIOS drives. This may take a long time. [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename. ] grub> root (hd0,0) root (hd0,0) Error 21: Selected disk does not exist grub> find /boot/grub/stage1 find /boot/grub/stage1 Error 15: File not found Fortunately, I got one person suggesting that what I've been trying to do is for GRUB Legacy, not GRUB2. So I went to the suggested website, ** (http://grub.enbug.org/Grub2LiveCdInstallGuide) **try to look around, and try: ubuntu@ubuntu:~$ sudo fdisk -l Unable to seek on /dev/sda This is just the step 2 of the instruction in the http://grub.enbug.org/Grub2LiveCdInstallGuide and I cannot proceed because it cannot seek /dev/sda. However, ubuntu@ubuntu:~$ sudo dmraid -r /dev/sdb: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 /dev/sda: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 So what now? Do you have an idea for how to make fdisk see my RAID array on live cd (Ubuntu 10.10)? Honestly, I am lost, very lost in trying to restore GRUB2 on this software RAID 0 system right now.

    Read the article

  • Restoring GRUB2 on Software RAID 0 after Windows 7 wiped it using LiveCD

    - by unknownthreat
    I have installed Ubuntu 10.10 on my system. However, I need to install Windows 7 back, and I expect that it would alter GRUB and it did. Right now, my partition on my Software RAID 0 looks like this: nvidia_acajefec1 is Ubuntu 10.10 and nvidia_acajefec3 is Windows 7. I've been following some guides around and I am always stuck at GRUB not able to detect the usual RAID content. I've tried running: sudo grub > root (hd0,0) GRUB complains it couldn't find my hard disk. So I tried: find (hd0,0) And it complains that it couldn't find anything. So I tried: find /boot/grub/stage1 It said "file not found". Here's the text from the console: ubuntu@ubuntu:~$ grub Probing devices to guess BIOS drives. This may take a long time. [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename. ] grub> root (hd0,0) root (hd0,0) Error 21: Selected disk does not exist grub> find /boot/grub/stage1 find /boot/grub/stage1 Error 15: File not found Fortunately, I got one person suggesting that what I've been trying to do is for GRUB Legacy, not GRUB2. So I went to the suggested website, ** (http://grub.enbug.org/Grub2LiveCdInstallGuide) **try to look around, and try: ubuntu@ubuntu:~$ sudo fdisk -l Unable to seek on /dev/sda This is just the step 2 of the instruction in the http://grub.enbug.org/Grub2LiveCdInstallGuide and I cannot proceed because it cannot seek /dev/sda. However, ubuntu@ubuntu:~$ sudo dmraid -r /dev/sdb: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 /dev/sda: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 So what now? Do you have an idea for how to make fdisk see my RAID array on live cd (Ubuntu 10.10)? Honestly, I am lost, very lost in trying to restore GRUB2 on this software RAID 0 system right now.

    Read the article

  • Restoring GRUB2 on Software RAID 0 using LiveCD after Windows 7 wiped it

    - by unknownthreat
    I have installed Ubuntu 10.10 on my system. However, I need to install Windows 7 back, and I expect that it would alter GRUB and it did. Right now, my partition on my Software RAID 0 looks like this: nvidia_acajefec1 is Ubuntu 10.10 and nvidia_acajefec3 is Windows 7. I've been following some guides around and I am always stuck at GRUB not able to detect the usual RAID content. I've tried running: sudo grub > root (hd0,0) GRUB complains it couldn't find my hard disk. So I tried: find (hd0,0) And it complains that it couldn't find anything. So I tried: find /boot/grub/stage1 It said "file not found". Here's the text from the console: ubuntu@ubuntu:~$ grub Probing devices to guess BIOS drives. This may take a long time. [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename. ] grub> root (hd0,0) root (hd0,0) Error 21: Selected disk does not exist grub> find /boot/grub/stage1 find /boot/grub/stage1 Error 15: File not found Fortunately, I got one person suggesting that what I've been trying to do is for GRUB Legacy, not GRUB2. So I went to the suggested website, ** (http://grub.enbug.org/Grub2LiveCdInstallGuide) **try to look around, and try: ubuntu@ubuntu:~$ sudo fdisk -l Unable to seek on /dev/sda This is just the step 2 of the instruction in the http://grub.enbug.org/Grub2LiveCdInstallGuide and I cannot proceed because it cannot seek /dev/sda. However, ubuntu@ubuntu:~$ sudo dmraid -r /dev/sdb: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 /dev/sda: nvidia, "nvidia_acajefec", stripe, ok, 488397166 sectors, data@ 0 So what now? Do you have an idea for how to make fdisk see my RAID array on live cd (Ubuntu 10.10)? Honestly, I am lost, very lost in trying to restore GRUB2 on this software RAID 0 system right now.

    Read the article

  • Did I lose my RAID again?

    - by BarsMonster
    Hi! A little history: 2 years ago I was really excited to find out that mdadm is so powerful that it even can reshape arrays, so you can start with a smaller array and then grow it as you need. I've bought 3x1Tb drives and made a RAID-5. It was fine for a year. Then I bought 2x more, and tried to reshape to RAID-6 out of 5 drives, and due to some mess with superblock versions, lost all content. Had to rebuild it from scratch, but 2Tb of data were gone. Yesterday I bought 2 more drives, and this time I had everything: properly built array, UPS. I've disabled write intent map, added 2 new drives as spares and run a command to grow array to 7-disks. It started working, but speed was ridiculously slow, ~100kb/sec. After processing first 37Mb at such an amazing speed, one of old HDDs fails. I properly shutdown the PC and disconnected the failed drive. After bootup it appeared that it recreated the intent map as it was still in mdadm config, so I removed it from config and rebooted again. Now all I see is that all mdadm processes deadlock, and don't do anything. PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1937 root 20 0 12992 608 444 D 0 0.1 0:00.00 mdadm 2283 root 20 0 12992 852 704 D 0 0.1 0:00.01 mdadm 2287 root 20 0 0 0 0 D 0 0.0 0:00.01 md0_reshape 2288 root 18 -2 12992 820 676 D 0 0.1 0:00.01 mdadm And all I see in mdstat is: $ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sdb1[1] sdg1[4] sdf1[7] sde1[6] sdd1[0] sdc1[5] 2929683456 blocks super 1.2 level 6, 1024k chunk, algorithm 2 [7/6] [UU_UUUU] [>....................] reshape = 0.0% (37888/976561152) finish=567604147.2min speed=0K/sec I've already tried mdadm 2.6.7, 3.1.4 and 3.2 - nothing helps. Did I lose my data again? Any suggestions on how can I make this work? OS is Ubuntu Server 10.04.2. PS. Needless to say, the data is inaccessible - I cannot mount /dev/md0 to save the most valuable data. You can see my disappointment - the very specific thing I was excited about failed twice taking 5Tb of my data with it. Update: It appears there is some nice info in kern.log: 21:38:48 ...: [ 166.522055] raid5: reshape will continue 21:38:48 ...: [ 166.522085] raid5: device sdb1 operational as raid disk 1 21:38:48 ...: [ 166.522091] raid5: device sdg1 operational as raid disk 4 21:38:48 ...: [ 166.522097] raid5: device sdf1 operational as raid disk 5 21:38:48 ...: [ 166.522102] raid5: device sde1 operational as raid disk 6 21:38:48 ...: [ 166.522107] raid5: device sdd1 operational as raid disk 0 21:38:48 ...: [ 166.522111] raid5: device sdc1 operational as raid disk 3 21:38:48 ...: [ 166.523942] raid5: allocated 7438kB for md0 21:38:48 ...: [ 166.524041] 1: w=1 pa=2 pr=5 m=2 a=2 r=7 op1=0 op2=0 21:38:48 ...: [ 166.524050] 4: w=2 pa=2 pr=5 m=2 a=2 r=7 op1=0 op2=0 21:38:48 ...: [ 166.524056] 5: w=3 pa=2 pr=5 m=2 a=2 r=7 op1=0 op2=0 21:38:48 ...: [ 166.524062] 6: w=4 pa=2 pr=5 m=2 a=2 r=7 op1=0 op2=0 21:38:48 ...: [ 166.524068] 0: w=5 pa=2 pr=5 m=2 a=2 r=7 op1=0 op2=0 21:38:48 ...: [ 166.524073] 3: w=6 pa=2 pr=5 m=2 a=2 r=7 op1=0 op2=0 21:38:48 ...: [ 166.524079] raid5: raid level 6 set md0 active with 6 out of 7 devices, algorithm 2 21:38:48 ...: [ 166.524519] RAID5 conf printout: 21:38:48 ...: [ 166.524523] --- rd:7 wd:6 21:38:48 ...: [ 166.524528] disk 0, o:1, dev:sdd1 21:38:48 ...: [ 166.524532] disk 1, o:1, dev:sdb1 21:38:48 ...: [ 166.524537] disk 3, o:1, dev:sdc1 21:38:48 ...: [ 166.524541] disk 4, o:1, dev:sdg1 21:38:48 ...: [ 166.524545] disk 5, o:1, dev:sdf1 21:38:48 ...: [ 166.524550] disk 6, o:1, dev:sde1 21:38:48 ...: [ 166.524553] ...ok start reshape thread 21:38:48 ...: [ 166.524727] md0: detected capacity change from 0 to 2999995858944 21:38:48 ...: [ 166.524735] md: reshape of RAID array md0 21:38:48 ...: [ 166.524740] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. 21:38:48 ...: [ 166.524745] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reshape. 21:38:48 ...: [ 166.524756] md: using 128k window, over a total of 976561152 blocks. 21:39:05 ...: [ 166.525013] md0: 21:42:04 ...: [ 362.520063] INFO: task mdadm:1937 blocked for more than 120 seconds. 21:42:04 ...: [ 362.520068] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:42:04 ...: [ 362.520073] mdadm D 00000000ffffffff 0 1937 1 0x00000000 21:42:04 ...: [ 362.520083] ffff88002ef4f5d8 0000000000000082 0000000000015bc0 0000000000015bc0 21:42:04 ...: [ 362.520092] ffff88002eb5b198 ffff88002ef4ffd8 0000000000015bc0 ffff88002eb5ade0 21:42:04 ...: [ 362.520100] 0000000000015bc0 ffff88002ef4ffd8 0000000000015bc0 ffff88002eb5b198 21:42:04 ...: [ 362.520107] Call Trace: 21:42:04 ...: [ 362.520133] [<ffffffffa0224892>] get_active_stripe+0x312/0x3f0 [raid456] 21:42:04 ...: [ 362.520148] [<ffffffff81059ae0>] ? default_wake_function+0x0/0x20 21:42:04 ...: [ 362.520159] [<ffffffffa0228413>] make_request+0x243/0x4b0 [raid456] 21:42:04 ...: [ 362.520169] [<ffffffffa0221a90>] ? release_stripe+0x50/0x70 [raid456] 21:42:04 ...: [ 362.520179] [<ffffffff81084790>] ? autoremove_wake_function+0x0/0x40 21:42:04 ...: [ 362.520188] [<ffffffff81414df0>] md_make_request+0xc0/0x130 21:42:04 ...: [ 362.520194] [<ffffffff81414df0>] ? md_make_request+0xc0/0x130 21:42:04 ...: [ 362.520205] [<ffffffff8129f8c1>] generic_make_request+0x1b1/0x4f0 21:42:04 ...: [ 362.520214] [<ffffffff810f6515>] ? mempool_alloc_slab+0x15/0x20 21:42:04 ...: [ 362.520222] [<ffffffff8116c2ec>] ? alloc_buffer_head+0x1c/0x60 21:42:04 ...: [ 362.520230] [<ffffffff8129fc80>] submit_bio+0x80/0x110 21:42:04 ...: [ 362.520236] [<ffffffff8116c849>] submit_bh+0xf9/0x140 21:42:04 ...: [ 362.520244] [<ffffffff8116f124>] block_read_full_page+0x274/0x3b0 21:42:04 ...: [ 362.520251] [<ffffffff81172c90>] ? blkdev_get_block+0x0/0x70 21:42:04 ...: [ 362.520258] [<ffffffff8110d875>] ? __inc_zone_page_state+0x35/0x40 21:42:04 ...: [ 362.520265] [<ffffffff810f46d8>] ? add_to_page_cache_locked+0xe8/0x160 21:42:04 ...: [ 362.520272] [<ffffffff81173d78>] blkdev_readpage+0x18/0x20 21:42:04 ...: [ 362.520279] [<ffffffff810f484b>] __read_cache_page+0x7b/0xe0 21:42:04 ...: [ 362.520285] [<ffffffff81173d60>] ? blkdev_readpage+0x0/0x20 21:42:04 ...: [ 362.520290] [<ffffffff81173d60>] ? blkdev_readpage+0x0/0x20 21:42:04 ...: [ 362.520297] [<ffffffff810f57dc>] do_read_cache_page+0x3c/0x120 21:42:04 ...: [ 362.520304] [<ffffffff810f5909>] read_cache_page_async+0x19/0x20 21:42:04 ...: [ 362.520310] [<ffffffff810f591e>] read_cache_page+0xe/0x20 21:42:04 ...: [ 362.520317] [<ffffffff811a6cb0>] read_dev_sector+0x30/0xa0 21:42:04 ...: [ 362.520324] [<ffffffff811a7fcd>] amiga_partition+0x6d/0x460 21:42:04 ...: [ 362.520331] [<ffffffff811a7938>] check_partition+0x138/0x190 21:42:04 ...: [ 362.520338] [<ffffffff811a7a7a>] rescan_partitions+0xea/0x2f0 21:42:04 ...: [ 362.520344] [<ffffffff811744c7>] __blkdev_get+0x267/0x3d0 21:42:04 ...: [ 362.520350] [<ffffffff81174650>] ? blkdev_open+0x0/0xc0 21:42:04 ...: [ 362.520356] [<ffffffff81174640>] blkdev_get+0x10/0x20 21:42:04 ...: [ 362.520362] [<ffffffff811746c1>] blkdev_open+0x71/0xc0 21:42:04 ...: [ 362.520369] [<ffffffff811419f3>] __dentry_open+0x113/0x370 21:42:04 ...: [ 362.520377] [<ffffffff81253f8f>] ? security_inode_permission+0x1f/0x30 21:42:04 ...: [ 362.520385] [<ffffffff8114de3f>] ? inode_permission+0xaf/0xd0 21:42:04 ...: [ 362.520391] [<ffffffff81141d67>] nameidata_to_filp+0x57/0x70 21:42:04 ...: [ 362.520398] [<ffffffff8115207a>] do_filp_open+0x2da/0xba0 21:42:04 ...: [ 362.520406] [<ffffffff811134a8>] ? unmap_vmas+0x178/0x310 21:42:04 ...: [ 362.520414] [<ffffffff8115dbfa>] ? alloc_fd+0x10a/0x150 21:42:04 ...: [ 362.520421] [<ffffffff81141769>] do_sys_open+0x69/0x170 21:42:04 ...: [ 362.520428] [<ffffffff811418b0>] sys_open+0x20/0x30 21:42:04 ...: [ 362.520437] [<ffffffff810121b2>] system_call_fastpath+0x16/0x1b 21:42:04 ...: [ 362.520446] INFO: task mdadm:2283 blocked for more than 120 seconds. 21:42:04 ...: [ 362.520450] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:42:04 ...: [ 362.520454] mdadm D 0000000000000000 0 2283 2212 0x00000000 21:42:04 ...: [ 362.520462] ffff88002cca7d98 0000000000000086 0000000000015bc0 0000000000015bc0 21:42:04 ...: [ 362.520470] ffff88002ededf78 ffff88002cca7fd8 0000000000015bc0 ffff88002ededbc0 21:42:04 ...: [ 362.520478] 0000000000015bc0 ffff88002cca7fd8 0000000000015bc0 ffff88002ededf78 21:42:04 ...: [ 362.520485] Call Trace: 21:42:04 ...: [ 362.520495] [<ffffffff81543a97>] __mutex_lock_slowpath+0xf7/0x180 21:42:04 ...: [ 362.520502] [<ffffffff8154397b>] mutex_lock+0x2b/0x50 21:42:04 ...: [ 362.520508] [<ffffffff8117404d>] __blkdev_put+0x3d/0x190 21:42:04 ...: [ 362.520514] [<ffffffff811741b0>] blkdev_put+0x10/0x20 21:42:04 ...: [ 362.520520] [<ffffffff811741f3>] blkdev_close+0x33/0x60 21:42:04 ...: [ 362.520527] [<ffffffff81145375>] __fput+0xf5/0x210 21:42:04 ...: [ 362.520534] [<ffffffff811454b5>] fput+0x25/0x30 21:42:04 ...: [ 362.520540] [<ffffffff811415ad>] filp_close+0x5d/0x90 21:42:04 ...: [ 362.520546] [<ffffffff81141697>] sys_close+0xb7/0x120 21:42:04 ...: [ 362.520553] [<ffffffff810121b2>] system_call_fastpath+0x16/0x1b 21:42:04 ...: [ 362.520559] INFO: task md0_reshape:2287 blocked for more than 120 seconds. 21:42:04 ...: [ 362.520563] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:42:04 ...: [ 362.520567] md0_reshape D ffff88003aee96f0 0 2287 2 0x00000000 21:42:04 ...: [ 362.520575] ffff88003cf05a70 0000000000000046 0000000000015bc0 0000000000015bc0 21:42:04 ...: [ 362.520582] ffff88003aee9aa8 ffff88003cf05fd8 0000000000015bc0 ffff88003aee96f0 21:42:04 ...: [ 362.520590] 0000000000015bc0 ffff88003cf05fd8 0000000000015bc0 ffff88003aee9aa8 21:42:04 ...: [ 362.520597] Call Trace: 21:42:04 ...: [ 362.520608] [<ffffffffa0224892>] get_active_stripe+0x312/0x3f0 [raid456] 21:42:04 ...: [ 362.520616] [<ffffffff81059ae0>] ? default_wake_function+0x0/0x20 21:42:04 ...: [ 362.520626] [<ffffffffa0226f80>] reshape_request+0x4c0/0x9a0 [raid456] 21:42:04 ...: [ 362.520634] [<ffffffff81084790>] ? autoremove_wake_function+0x0/0x40 21:42:04 ...: [ 362.520644] [<ffffffffa022777a>] sync_request+0x31a/0x3a0 [raid456] 21:42:04 ...: [ 362.520651] [<ffffffff81052713>] ? __wake_up+0x53/0x70 21:42:04 ...: [ 362.520658] [<ffffffff814156b1>] md_do_sync+0x621/0xbb0 21:42:04 ...: [ 362.520668] [<ffffffff810387b9>] ? default_spin_lock_flags+0x9/0x10 21:42:04 ...: [ 362.520675] [<ffffffff8141640c>] md_thread+0x5c/0x130 21:42:04 ...: [ 362.520681] [<ffffffff81084790>] ? autoremove_wake_function+0x0/0x40 21:42:04 ...: [ 362.520688] [<ffffffff814163b0>] ? md_thread+0x0/0x130 21:42:04 ...: [ 362.520694] [<ffffffff81084416>] kthread+0x96/0xa0 21:42:04 ...: [ 362.520701] [<ffffffff810131ea>] child_rip+0xa/0x20 21:42:04 ...: [ 362.520707] [<ffffffff81084380>] ? kthread+0x0/0xa0 21:42:04 ...: [ 362.520713] [<ffffffff810131e0>] ? child_rip+0x0/0x20 21:42:04 ...: [ 362.520718] INFO: task mdadm:2288 blocked for more than 120 seconds. 21:42:04 ...: [ 362.520721] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:42:04 ...: [ 362.520725] mdadm D 0000000000000000 0 2288 1 0x00000000 21:42:04 ...: [ 362.520733] ffff88002cca9c18 0000000000000086 0000000000015bc0 0000000000015bc0 21:42:04 ...: [ 362.520741] ffff88003aee83b8 ffff88002cca9fd8 0000000000015bc0 ffff88003aee8000 21:42:04 ...: [ 362.520748] 0000000000015bc0 ffff88002cca9fd8 0000000000015bc0 ffff88003aee83b8 21:42:04 ...: [ 362.520755] Call Trace: 21:42:04 ...: [ 362.520763] [<ffffffff81543a97>] __mutex_lock_slowpath+0xf7/0x180 21:42:04 ...: [ 362.520771] [<ffffffff812a6d50>] ? exact_match+0x0/0x10 21:42:04 ...: [ 362.520777] [<ffffffff8154397b>] mutex_lock+0x2b/0x50 21:42:04 ...: [ 362.520783] [<ffffffff811742c8>] __blkdev_get+0x68/0x3d0 21:42:04 ...: [ 362.520790] [<ffffffff81174650>] ? blkdev_open+0x0/0xc0 21:42:04 ...: [ 362.520795] [<ffffffff81174640>] blkdev_get+0x10/0x20 21:42:04 ...: [ 362.520801] [<ffffffff811746c1>] blkdev_open+0x71/0xc0 21:42:04 ...: [ 362.520808] [<ffffffff811419f3>] __dentry_open+0x113/0x370 21:42:04 ...: [ 362.520815] [<ffffffff81253f8f>] ? security_inode_permission+0x1f/0x30 21:42:04 ...: [ 362.520821] [<ffffffff8114de3f>] ? inode_permission+0xaf/0xd0 21:42:04 ...: [ 362.520828] [<ffffffff81141d67>] nameidata_to_filp+0x57/0x70 21:42:04 ...: [ 362.520834] [<ffffffff8115207a>] do_filp_open+0x2da/0xba0 21:42:04 ...: [ 362.520841] [<ffffffff810ff0e1>] ? lru_cache_add_lru+0x21/0x40 21:42:04 ...: [ 362.520848] [<ffffffff8111109c>] ? do_anonymous_page+0x11c/0x330 21:42:04 ...: [ 362.520855] [<ffffffff81115d5f>] ? handle_mm_fault+0x31f/0x3c0 21:42:04 ...: [ 362.520862] [<ffffffff8115dbfa>] ? alloc_fd+0x10a/0x150 21:42:04 ...: [ 362.520868] [<ffffffff81141769>] do_sys_open+0x69/0x170 21:42:04 ...: [ 362.520874] [<ffffffff811418b0>] sys_open+0x20/0x30 21:42:04 ...: [ 362.520882] [<ffffffff810121b2>] system_call_fastpath+0x16/0x1b 21:44:04 ...: [ 482.520065] INFO: task mdadm:1937 blocked for more than 120 seconds. 21:44:04 ...: [ 482.520071] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:44:04 ...: [ 482.520077] mdadm D 00000000ffffffff 0 1937 1 0x00000000 21:44:04 ...: [ 482.520087] ffff88002ef4f5d8 0000000000000082 0000000000015bc0 0000000000015bc0 21:44:04 ...: [ 482.520096] ffff88002eb5b198 ffff88002ef4ffd8 0000000000015bc0 ffff88002eb5ade0 21:44:04 ...: [ 482.520104] 0000000000015bc0 ffff88002ef4ffd8 0000000000015bc0 ffff88002eb5b198 21:44:04 ...: [ 482.520112] Call Trace: 21:44:04 ...: [ 482.520139] [<ffffffffa0224892>] get_active_stripe+0x312/0x3f0 [raid456] 21:44:04 ...: [ 482.520154] [<ffffffff81059ae0>] ? default_wake_function+0x0/0x20 21:44:04 ...: [ 482.520165] [<ffffffffa0228413>] make_request+0x243/0x4b0 [raid456] 21:44:04 ...: [ 482.520175] [<ffffffffa0221a90>] ? release_stripe+0x50/0x70 [raid456] 21:44:04 ...: [ 482.520185] [<ffffffff81084790>] ? autoremove_wake_function+0x0/0x40 21:44:04 ...: [ 482.520194] [<ffffffff81414df0>] md_make_request+0xc0/0x130 21:44:04 ...: [ 482.520201] [<ffffffff81414df0>] ? md_make_request+0xc0/0x130 21:44:04 ...: [ 482.520212] [<ffffffff8129f8c1>] generic_make_request+0x1b1/0x4f0 21:44:04 ...: [ 482.520221] [<ffffffff810f6515>] ? mempool_alloc_slab+0x15/0x20 21:44:04 ...: [ 482.520229] [<ffffffff8116c2ec>] ? alloc_buffer_head+0x1c/0x60 21:44:04 ...: [ 482.520237] [<ffffffff8129fc80>] submit_bio+0x80/0x110 21:44:04 ...: [ 482.520244] [<ffffffff8116c849>] submit_bh+0xf9/0x140 21:44:04 ...: [ 482.520252] [<ffffffff8116f124>] block_read_full_page+0x274/0x3b0 21:44:04 ...: [ 482.520258] [<ffffffff81172c90>] ? blkdev_get_block+0x0/0x70 21:44:04 ...: [ 482.520266] [<ffffffff8110d875>] ? __inc_zone_page_state+0x35/0x40 21:44:04 ...: [ 482.520273] [<ffffffff810f46d8>] ? add_to_page_cache_locked+0xe8/0x160 21:44:04 ...: [ 482.520280] [<ffffffff81173d78>] blkdev_readpage+0x18/0x20 21:44:04 ...: [ 482.520286] [<ffffffff810f484b>] __read_cache_page+0x7b/0xe0 21:44:04 ...: [ 482.520293] [<ffffffff81173d60>] ? blkdev_readpage+0x0/0x20 21:44:04 ...: [ 482.520299] [<ffffffff81173d60>] ? blkdev_readpage+0x0/0x20 21:44:04 ...: [ 482.520306] [<ffffffff810f57dc>] do_read_cache_page+0x3c/0x120 21:44:04 ...: [ 482.520313] [<ffffffff810f5909>] read_cache_page_async+0x19/0x20 21:44:04 ...: [ 482.520319] [<ffffffff810f591e>] read_cache_page+0xe/0x20 21:44:04 ...: [ 482.520327] [<ffffffff811a6cb0>] read_dev_sector+0x30/0xa0 21:44:04 ...: [ 482.520334] [<ffffffff811a7fcd>] amiga_partition+0x6d/0x460 21:44:04 ...: [ 482.520341] [<ffffffff811a7938>] check_partition+0x138/0x190 21:44:04 ...: [ 482.520348] [<ffffffff811a7a7a>] rescan_partitions+0xea/0x2f0 21:44:04 ...: [ 482.520355] [<ffffffff811744c7>] __blkdev_get+0x267/0x3d0 21:44:04 ...: [ 482.520361] [<ffffffff81174650>] ? blkdev_open+0x0/0xc0 21:44:04 ...: [ 482.520367] [<ffffffff81174640>] blkdev_get+0x10/0x20 21:44:04 ...: [ 482.520373] [<ffffffff811746c1>] blkdev_open+0x71/0xc0 21:44:04 ...: [ 482.520380] [<ffffffff811419f3>] __dentry_open+0x113/0x370 21:44:04 ...: [ 482.520388] [<ffffffff81253f8f>] ? security_inode_permission+0x1f/0x30 21:44:04 ...: [ 482.520396] [<ffffffff8114de3f>] ? inode_permission+0xaf/0xd0 21:44:04 ...: [ 482.520403] [<ffffffff81141d67>] nameidata_to_filp+0x57/0x70 21:44:04 ...: [ 482.520410] [<ffffffff8115207a>] do_filp_open+0x2da/0xba0 21:44:04 ...: [ 482.520417] [<ffffffff811134a8>] ? unmap_vmas+0x178/0x310 21:44:04 ...: [ 482.520426] [<ffffffff8115dbfa>] ? alloc_fd+0x10a/0x150 21:44:04 ...: [ 482.520432] [<ffffffff81141769>] do_sys_open+0x69/0x170 21:44:04 ...: [ 482.520438] [<ffffffff811418b0>] sys_open+0x20/0x30 21:44:04 ...: [ 482.520447] [<ffffffff810121b2>] system_call_fastpath+0x16/0x1b 21:44:04 ...: [ 482.520458] INFO: task mdadm:2283 blocked for more than 120 seconds. 21:44:04 ...: [ 482.520462] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:44:04 ...: [ 482.520467] mdadm D 0000000000000000 0 2283 2212 0x00000000 21:44:04 ...: [ 482.520475] ffff88002cca7d98 0000000000000086 0000000000015bc0 0000000000015bc0 21:44:04 ...: [ 482.520483] ffff88002ededf78 ffff88002cca7fd8 0000000000015bc0 ffff88002ededbc0 21:44:04 ...: [ 482.520490] 0000000000015bc0 ffff88002cca7fd8 0000000000015bc0 ffff88002ededf78 21:44:04 ...: [ 482.520498] Call Trace: 21:44:04 ...: [ 482.520508] [<ffffffff81543a97>] __mutex_lock_slowpath+0xf7/0x180 21:44:04 ...: [ 482.520515] [<ffffffff8154397b>] mutex_lock+0x2b/0x50 21:44:04 ...: [ 482.520521] [<ffffffff8117404d>] __blkdev_put+0x3d/0x190 21:44:04 ...: [ 482.520527] [<ffffffff811741b0>] blkdev_put+0x10/0x20 21:44:04 ...: [ 482.520533] [<ffffffff811741f3>] blkdev_close+0x33/0x60 21:44:04 ...: [ 482.520541] [<ffffffff81145375>] __fput+0xf5/0x210 21:44:04 ...: [ 482.520547] [<ffffffff811454b5>] fput+0x25/0x30 21:44:04 ...: [ 482.520554] [<ffffffff811415ad>] filp_close+0x5d/0x90 21:44:04 ...: [ 482.520560] [<ffffffff81141697>] sys_close+0xb7/0x120 21:44:04 ...: [ 482.520568] [<ffffffff810121b2>] system_call_fastpath+0x16/0x1b 21:44:04 ...: [ 482.520574] INFO: task md0_reshape:2287 blocked for more than 120 seconds. 21:44:04 ...: [ 482.520578] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:44:04 ...: [ 482.520582] md0_reshape D ffff88003aee96f0 0 2287 2 0x00000000 21:44:04 ...: [ 482.520590] ffff88003cf05a70 0000000000000046 0000000000015bc0 0000000000015bc0 21:44:04 ...: [ 482.520597] ffff88003aee9aa8 ffff88003cf05fd8 0000000000015bc0 ffff88003aee96f0 21:44:04 ...: [ 482.520605] 0000000000015bc0 ffff88003cf05fd8 0000000000015bc0 ffff88003aee9aa8 21:44:04 ...: [ 482.520612] Call Trace: 21:44:04 ...: [ 482.520623] [<ffffffffa0224892>] get_active_stripe+0x312/0x3f0 [raid456] 21:44:04 ...: [ 482.520633] [<ffffffff81059ae0>] ? default_wake_function+0x0/0x20 21:44:04 ...: [ 482.520643] [<ffffffffa0226f80>] reshape_request+0x4c0/0x9a0 [raid456] 21:44:04 ...: [ 482.520651] [<ffffffff81084790>] ? autoremove_wake_function+0x0/0x40 21:44:04 ...: [ 482.520661] [<ffffffffa022777a>] sync_request+0x31a/0x3a0 [raid456] 21:44:04 ...: [ 482.520668] [<ffffffff81052713>] ? __wake_up+0x53/0x70 21:44:04 ...: [ 482.520675] [<ffffffff814156b1>] md_do_sync+0x621/0xbb0 21:44:04 ...: [ 482.520685] [<ffffffff810387b9>] ? default_spin_lock_flags+0x9/0x10 21:44:04 ...: [ 482.520692] [<ffffffff8141640c>] md_thread+0x5c/0x130 21:44:04 ...: [ 482.520699] [<ffffffff81084790>] ? autoremove_wake_function+0x0/0x40 21:44:04 ...: [ 482.520705] [<ffffffff814163b0>] ? md_thread+0x0/0x130 21:44:04 ...: [ 482.520711] [<ffffffff81084416>] kthread+0x96/0xa0 21:44:04 ...: [ 482.520718] [<ffffffff810131ea>] child_rip+0xa/0x20 21:44:04 ...: [ 482.520725] [<ffffffff81084380>] ? kthread+0x0/0xa0 21:44:04 ...: [ 482.520730] [<ffffffff810131e0>] ? child_rip+0x0/0x20 21:44:04 ...: [ 482.520735] INFO: task mdadm:2288 blocked for more than 120 seconds. 21:44:04 ...: [ 482.520739] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:44:04 ...: [ 482.520743] mdadm D 0000000000000000 0 2288 1 0x00000000 21:44:04 ...: [ 482.520751] ffff88002cca9c18 0000000000000086 0000000000015bc0 0000000000015bc0 21:44:04 ...: [ 482.520759] ffff88003aee83b8 ffff88002cca9fd8 0000000000015bc0 ffff88003aee8000 21:44:04 ...: [ 482.520767] 0000000000015bc0 ffff88002cca9fd8 0000000000015bc0 ffff88003aee83b8 21:44:04 ...: [ 482.520774] Call Trace: 21:44:04 ...: [ 482.520782] [<ffffffff81543a97>] __mutex_lock_slowpath+0xf7/0x180 21:44:04 ...: [ 482.520790] [<ffffffff812a6d50>] ? exact_match+0x0/0x10 21:44:04 ...: [ 482.520797] [<ffffffff8154397b>] mutex_lock+0x2b/0x50 21:44:04 ...: [ 482.520804] [<ffffffff811742c8>] __blkdev_get+0x68/0x3d0 21:44:04 ...: [ 482.520810] [<ffffffff81174650>] ? blkdev_open+0x0/0xc0 21:44:04 ...: [ 482.520816] [<ffffffff81174640>] blkdev_get+0x10/0x20 21:44:04 ...: [ 482.520822] [<ffffffff811746c1>] blkdev_open+0x71/0xc0 21:44:04 ...: [ 482.520829] [<ffffffff811419f3>] __dentry_open+0x113/0x370 21:44:04 ...: [ 482.520837] [<ffffffff81253f8f>] ? security_inode_permission+0x1f/0x30 21:44:04 ...: [ 482.520843] [<ffffffff8114de3f>] ? inode_permission+0xaf/0xd0 21:44:04 ...: [ 482.520850] [<ffffffff81141d67>] nameidata_to_filp+0x57/0x70 21:44:04 ...: [ 482.520857] [<ffffffff8115207a>] do_filp_open+0x2da/0xba0 21:44:04 ...: [ 482.520864] [<ffffffff810ff0e1>] ? lru_cache_add_lru+0x21/0x40 21:44:04 ...: [ 482.520871] [<ffffffff8111109c>] ? do_anonymous_page+0x11c/0x330 21:44:04 ...: [ 482.520878] [<ffffffff81115d5f>] ? handle_mm_fault+0x31f/0x3c0 21:44:04 ...: [ 482.520885] [<ffffffff8115dbfa>] ? alloc_fd+0x10a/0x150 21:44:04 ...: [ 482.520891] [<ffffffff81141769>] do_sys_open+0x69/0x170 21:44:04 ...: [ 482.520897] [<ffffffff811418b0>] sys_open+0x20/0x30 21:44:04 ...: [ 482.520905] [<ffffffff810121b2>] system_call_fastpath+0x16/0x1b 21:46:04 ...: [ 602.520053] INFO: task mdadm:1937 blocked for more than 120 seconds. 21:46:04 ...: [ 602.520059] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:46:04 ...: [ 602.520065] mdadm D 00000000ffffffff 0 1937 1 0x00000000 21:46:04 ...: [ 602.520075] ffff88002ef4f5d8 0000000000000082 0000000000015bc0 0000000000015bc0 21:46:04 ...: [ 602.520084] ffff88002eb5b198 ffff88002ef4ffd8 0000000000015bc0 ffff88002eb5ade0 21:46:04 ...: [ 602.520091] 0000000000015bc0 ffff88002ef4ffd8 0000000000015bc0 ffff88002eb5b198 21:46:04 ...: [ 602.520099] Call Trace: 21:46:04 ...: [ 602.520127] [<ffffffffa0224892>] get_active_stripe+0x312/0x3f0 [raid456] 21:46:04 ...: [ 602.520142] [<ffffffff81059ae0>] ? default_wake_function+0x0/0x20 21:46:04 ...: [ 602.520153] [<ffffffffa0228413>] make_request+0x243/0x4b0 [raid456] 21:46:04 ...: [ 602.520162] [<ffffffffa0221a90>] ? release_stripe+0x50/0x70 [raid456] 21:46:04 ...: [ 602.520171] [<ffffffff81084790>] ? autoremove_wake_function+0x0/0x40 21:46:04 ...: [ 602.520180] [<ffffffff81414df0>] md_make_request+0xc0/0x130 21:46:04 ...: [ 602.520187] [<ffffffff81414df0>] ? md_make_request+0xc0/0x130 21:46:04 ...: [ 602.520197] [<ffffffff8129f8c1>] generic_make_request+0x1b1/0x4f0 21:46:04 ...: [ 602.520206] [<ffffffff810f6515>] ? mempool_alloc_slab+0x15/0x20 21:46:04 ...: [ 602.520215] [<ffffffff8116c2ec>] ? alloc_buffer_head+0x1c/0x60 21:46:04 ...: [ 602.520222] [<ffffffff8129fc80>] submit_bio+0x80/0x110 21:46:04 ...: [ 602.520229] [<ffffffff8116c849>] submit_bh+0xf9/0x140 21:46:04 ...: [ 602.520237] [<ffffffff8116f124>] block_read_full_page+0x274/0x3b0 21:46:04 ...: [ 602.520244] [<ffffffff81172c90>] ? blkdev_get_block+0x0/0x70 21:46:04 ...: [ 602.520252] [<ffffffff8110d875>] ? __inc_zone_page_state+0x35/0x40 21:46:04 ...: [ 602.520259] [<ffffffff810f46d8>] ? add_to_page_cache_locked+0xe8/0x160 21:46:04 ...: [ 602.520266] [<ffffffff81173d78>] blkdev_readpage+0x18/0x20 21:46:04 ...: [ 602.520273] [<ffffffff810f484b>] __read_cache_page+0x7b/0xe0 21:46:04 ...: [ 602.520279] [<ffffffff81173d60>] ? blkdev_readpage+0x0/0x20 21:46:04 ...: [ 602.520285] [<ffffffff81173d60>] ? blkdev_readpage+0x0/0x20 21:46:04 ...: [ 602.520292] [<ffffffff810f57dc>] do_read_cache_page+0x3c/0x120 21:46:04 ...: [ 602.520300] [<ffffffff810f5909>] read_cache_page_async+0x19/0x20 21:46:04 ...: [ 602.520306] [<ffffffff810f591e>] read_cache_page+0xe/0x20 21:46:04 ...: [ 602.520314] [<ffffffff811a6cb0>] read_dev_sector+0x30/0xa0 21:46:04 ...: [ 602.520321] [<ffffffff811a7fcd>] amiga_partition+0x6d/0x460 21:46:04 ...: [ 602.520328] [<ffffffff811a7938>] check_partition+0x138/0x190 21:46:04 ...: [ 602.520335] [<ffffffff811a7a7a>] rescan_partitions+0xea/0x2f0 21:46:04 ...: [ 602.520342] [<ffffffff811744c7>] __blkdev_get+0x267/0x3d0 21:46:04 ...: [ 602.520348] [<ffffffff81174650>] ? blkdev_open+0x0/0xc0 21:46:04 ...: [ 602.520354] [<ffffffff81174640>] blkdev_get+0x10/0x20 21:46:04 ...: [ 602.520359] [<ffffffff811746c1>] blkdev_open+0x71/0xc0 21:46:04 ...: [ 602.520367] [<ffffffff811419f3>] __dentry_open+0x113/0x370 21:46:04 ...: [ 602.520375] [<ffffffff81253f8f>] ? security_inode_permission+0x1f/0x30 21:46:04 ...: [ 602.520383] [<ffffffff8114de3f>] ? inode_permission+0xaf/0xd0 21:46:04 ...: [ 602.520390] [<ffffffff81141d67>] nameidata_to_filp+0x57/0x70 21:46:04 ...: [ 602.520397] [<ffffffff8115207a>] do_filp_open+0x2da/0xba0 21:46:04 ...: [ 602.520404] [<ffffffff811134a8>] ? unmap_vmas+0x178/0x310 21:46:04 ...: [ 602.520413] [<ffffffff8115dbfa>] ? alloc_fd+0x10a/0x150 21:46:04 ...: [ 602.520419] [<ffffffff81141769>] do_sys_open+0x69/0x170 21:46:04 ...: [ 602.520425] [<ffffffff811418b0>] sys_open+0x20/0x30 21:46:04 ...: [ 602.520434] [<ffffffff810121b2>] system_call_fastpath+0x16/0x1b 21:46:04 ...: [ 602.520443] INFO: task mdadm:2283 blocked for more than 120 seconds. 21:46:04 ...: [ 602.520447] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. 21:46:04 ...: [ 602.520451] mdadm D 0000000000000000 0 2283 2212 0x00000000 21:46:04 ...: [ 602.520460] ffff88002cca7d98 0000000000000086 0000000000015bc0 0000000000015bc0 21:46:04 ...: [ 602.520468] ffff88002ededf78 ffff88002cca7fd8 0000000000015bc0 ffff88002ededbc0 21:46:04 ...: [ 602.520475] 0000000000015bc0 ffff88002cca7fd8 0000000000015bc0 ffff88002ededf78 21:46:04 ...: [ 602.520483] Call Trace: 21:46:04 ...: [ 602.520492] [<ffffffff81543a97>] __mutex_lock_slowpath+0xf7/0x180 21:46:04 ...: [ 602.520500] [<ffffffff8154397b>] mutex_lock+0x2b/0x50 21:46:04 ...: [ 602.520506] [<ffffffff8117404d>] __blkdev_put+0x3d/0x190 21:46:04 ...: [ 602.520512] [<ffffffff811741b0>] blkdev_put+0x10/0x20 21:46:04 ...: [ 602.520518] [<ffffffff811741f3>] blkdev_close+0x33/0x60 21:46:04 ...: [ 602.520526] [<ffffffff81145375>] __fput+0xf5/0x210 21:46:04 ...: [ 602.520533] [<ffffffff811454b5>] fput+0x25/0x30 21:46:04 ...: [ 602.520539] [<ffffffff811415ad>] filp_close+0x5d/0x90 21:46:04 ...: [ 602.520545] [<ffffffff81141697>] sys_close+0xb7/0x120 21:46:04 ...: [ 602.520552] [<ffffffff810121b2>] system_call_fastpath+0x16/0x1b

    Read the article

  • Installing Ubuntu 12.04.1 x64 with Fake RAID 1 [SOLVED]

    - by Arkadius
    I had: Software: Dual boot with Windows XP Ubuntu 10.04 LTS x32 Hardware Fake RAID 1 (mirroring) with 2x1 TB: Partition 1 - Windows Partition 2 - SWAP Partition 3 - / (root) Partition 4 - Extended Partition 5 - /home Partition 6 - /data arek@domek:/var/log/installer$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de1b9 Device Boot Start End Blocks Id System /dev/sda1 * 63 524297339 262148638+ 7 HPFS/NTFS/exFAT /dev/sda2 524297340 528506369 2104515 82 Linux swap / Solaris /dev/sda3 528506370 570468149 20980890 83 Linux /dev/sda4 570468150 1953118439 691325145 5 Extended /dev/sda5 570468213 675340469 52436128+ 83 Linux /dev/sda6 675340533 1953118439 638888953+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de1b9 Device Boot Start End Blocks Id System /dev/sdb1 * 63 524297339 262148638+ 7 HPFS/NTFS/exFAT /dev/sdb2 524297340 528506369 2104515 82 Linux swap / Solaris /dev/sdb3 528506370 570468149 20980890 83 Linux /dev/sdb4 570468150 1953118439 691325145 5 Extended /dev/sdb5 570468213 675340469 52436128+ 83 Linux /dev/sdb6 675340533 1953118439 638888953+ 83 Linux arek@domek:/var/log/installer$ ls -l /dev/mapper/ total 0 crw------- 1 root root 10, 236 Oct 7 20:17 control lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha -> ../dm-0 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha1 -> ../dm-1 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha2 -> ../dm-2 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha3 -> ../dm-3 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha4 -> ../dm-4 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha5 -> ../dm-5 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha6 -> ../dm-6 I wanted to upgrade from 10.04 x32 to 12.04 x64 using FRESH installation. So, run installation of Ubuntu 12.04.1 x64 LTS using alternate CD. During the installation I selected manual partitioning and to: - Use and Format / (root) - Use and Format SWAP - Use and Keep data on /home - Use and Keep data on /data After I clicked "Continue" I get error creating and formatting SWAP partition. I go to terminal with Alt + F2 (?) and hit enter. I discovered that there was visible RAID as only disk with NO partitions. Something like this: arek@domek:/var/log/installer$ ls -l /dev/mapper/ lrwxrwxrwx 1 root root 7 Oct 7 20:17 /dev/mapper/pdc_jhjbcaha -> ../dm-0 arek@domek:/var/log/installer$ ls -l /dev/dm* brw-rw---- 1 root disk 252, 0 Oct 7 20:17 /dev/dm-0 So I switched to log console Alt+F3 (?) and saw errors like below: Oct 7 14:02:45 check-missing-firmware: /dev/.udev/firmware-missing does not exist, skipping Oct 7 14:02:45 check-missing-firmware: /run/udev/firmware-missing does not exist, skipping Oct 7 14:02:45 check-missing-firmware: no missing firmware in /dev/.udev/firmware-missing /run/udev/firmware-missing Oct 7 14:02:45 anna-install: Installing dmraid-udeb Oct 7 14:02:45 anna[12599]: DEBUG: retrieving dmraid-udeb 1.0.0.rc16-4.1ubuntu8 Oct 7 14:02:49 anna[12599]: DEBUG: retrieving libdmraid1.0.0.rc16-udeb 1.0.0.rc16-4.1ubuntu8 Oct 7 14:02:49 anna[12599]: DEBUG: retrieving kpartx-udeb 0.4.9-3ubuntu5 Oct 7 14:02:49 disk-detect: Serial ATA RAID disk(s) detected. Oct 7 14:02:55 disk-detect: Enabling dmraid support. Oct 7 14:02:55 disk-detect: RAID set "pdc_jhjbcaha" was activated Oct 7 14:02:55 HERE --> dmraid-activate: ERROR: Cannot retrieve RAID set information for pdc_jhjbcaha Oct 7 14:02:56 check-missing-firmware: /dev/.udev/firmware-missing does not exist, skipping Oct 7 14:02:56 check-missing-firmware: /run/udev/firmware-missing does not exist, skipping Oct 7 14:02:56 check-missing-firmware: no missing firmware in /dev/.udev/firmware-missing /run/udev/firmware-missing Oct 7 14:02:57 main-menu[428]: DEBUG: resolver (libnewt0.52): package doesn't exist (ignored) Oct 7 14:02:57 main-menu[428]: DEBUG: resolver (ext2-modules): package doesn't exist (ignored) Oct 7 14:02:57 main-menu[428]: INFO: Menu item 'partman-base' selected Oct 7 14:02:57 kernel: [ 316.512999] NTFS driver 2.1.30 [Flags: R/O MODULE]. Oct 7 14:02:57 kernel: [ 316.523221] Btrfs loaded Oct 7 14:02:57 kernel: [ 316.534781] JFS: nTxBlock = 8192, nTxLock = 65536 Oct 7 14:02:57 kernel: [ 316.554749] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled Oct 7 14:02:57 kernel: [ 316.555336] SGI XFS Quota Management subsystem Oct 7 14:02:58 md-devices: mdadm: No arrays found in config file or automatically Oct 7 14:02:58 partman: No matching physical volumes found Oct 7 14:02:58 partman: No volume groups found Oct 7 14:02:58 partman: Reading all physical volumes. This may take a while... Oct 7 14:02:58 partman-lvm: No volume groups found Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:06:11 HERE --> partman: mkswap: can't open '/dev/mapper/pdc_jhjbcaha2': No such file or directory Oct 7 14:07:28 init: starting pid 401, tty '/dev/tty2': '-/bin/sh' Oct 7 14:15:00 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Oct 7 14:15:00 net/hw-detect.hotplug: Detected hotpluggable network interface lo As You can see there are 2 errors Oct 7 14:02:55 dmraid-activate: ERROR: Cannot retrieve RAID set information for pdc_jhjbcaha and Oct 7 14:06:11 partman: mkswap: can't open '/dev/mapper/pdc_jhjbcaha2': No such file or directory I looked in the internet and try to run command "dmraid -ay" and get something like that: dmraid -ay /dev/mapper/pdc_jhjbcaha -> Already activated /dev/mapper/pdc_jhjbcaha1 -> Successfully activated /dev/mapper/pdc_jhjbcaha2 -> Successfully activated /dev/mapper/pdc_jhjbcaha3 -> Successfully activated /dev/mapper/pdc_jhjbcaha4 -> Successfully activated /dev/mapper/pdc_jhjbcaha5 -> Successfully activated /dev/mapper/pdc_jhjbcaha6 -> Successfully activated Then I returned to installer with Alt+F1 (?) and click "Return" to return to partitioning menu. I did NOT change anything just selected again "Continue" and everything goes smoothly. I hope this will help someone. arkadius

    Read the article

  • new hard drive on Dell Adaptec 2610SA 6 port SATA RAID PCI card

    - by Ragnarok85
    I have a Dell Adaptec 2610SA 6 port SATA RAID PCI card with 3 hard drives on it and everything works fine. I plugged another hard drive to it and the system (Ubuntu 12.04, 64 bit) seems not to recognize it. Strange thing is that, as happened in the past, if I re-install the system, it recognizes the new hardware plugged to RAID card. Of course I don't want to re-install ubuntu each time I plug a new hard drive on my RAID card. Any idea? Thank you in advance

    Read the article

  • High CPU load for 1:30 minutes when mounting ext4-raid partition

    - by sirion
    I have a raid 5 (software) with 5x2TB drives. I encrypted the raid with cryptsetup and put an ext4-partition on top. In the beginning opening and mounting the raid took less than 10 seconds, now (for a few weeks) mounting alone takes 1:30 minutes and the cpu stays around 93% the whole time: The output of "time sudo mount /dev/mapper/8000 /media/8000" is: real 1m31.952s user 0m0.008s sys 1m25.229s At the same time only one line is added to /var/log/syslog: kernel: [ 2240.921381] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null) My Ubuntu-version is "12.04.1 LTS" and no updates are pending. I checked the partition with fsck, but it says that all is ok. The "cryptsetup luksOpen" command only takes a few seconds. I also tried changing the raid-bitmap (as it was suggested in some forum) but it did not change the behaviour. sudo mdadm --grow /dev/md0 -b internal and sudo mdadm --grow /dev/md0 -b none I had the idea that it might be the hardware being slow, but a read test with "sudo hdparm -t /dev/md0" spit out values between 62 and 159 MB/sec: Timing buffered disk reads: 382 MB in 3.00 seconds = 127.14 MB/sec Timing buffered disk reads: 482 MB in 3.02 seconds = 159.62 MB/sec Timing buffered disk reads: 190 MB in 3.03 seconds = 62.65 MB/sec Timing buffered disk reads: 474 MB in 3.02 seconds = 157.12 MB/sec Although I think it is strange that the read rate jumps by more than 100% - could that mean something? The speed test when reading from the mapped (decrypted) device shows similar behavior, although it is of course much slower. "sudo hdparm -t /dev/mapper/8000": Timing buffered disk reads: 56 MB in 3.02 seconds = 18.54 MB/sec Timing buffered disk reads: 122 MB in 3.09 seconds = 39.43 MB/sec Timing buffered disk reads: 134 MB in 3.02 seconds = 44.35 MB/sec The output of a verbose mount "mount -vvv /dev/mapper/8000 /media/8000" does not help much: mount: fstab path: "/etc/fstab" mount: mtab path: "/etc/mtab" mount: lock path: "/etc/mtab~" mount: temp path: "/etc/mtab.tmp" mount: UID: 0 mount: eUID: 0 mount: spec: "/dev/mapper/8000" mount: node: "/media/8000" mount: types: "(null)" mount: opts: "(null)" mount: you didn't specify a filesystem type for /dev/mapper/8000 I will try type ext4 mount: mount(2) syscall: source: "/dev/mapper/8000", target: "/media/8000", filesystemtype: "ext4", mountflags: -1058209792, data: (null) Any idea where I could find additional information on why mounting takes so long, or what additional tests I could run?

    Read the article

  • How do I get Windows 7 To Recognize a newly installed RAID 5 volume?

    - by GregH
    I had a previously running Windows 7 (64 bit) system. I added 3 new 1TB Seagate drives that I set up as a RAID 5 volume. I have a Gigabyte GA-P55M-UD2 motherboard. I installed the drives, set up the BIOS and configured the three drives as a RAID volume through the RAID setup utility that was accessed via Ctrl-I while the system was booting. I rebooted the system and could see the drives during the boot sequence. However, when Windows 7 was starting I got an error (quick blue screen) and then Windows tried to repair itself with no success. Do I need to install RAID drivers in Windows? How do I do it if Windows won't boot? Thanks in advance.

    Read the article

  • Why do I get a DegradedArray event with mdadm

    - by azera
    Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

    Read the article

  • Why has ESXi 5.0 not used the software RAID configuration on my test server?

    - by kafka
    I've got a test server which was running WS 2008 Enterprise on the bare metal. It was correctly using the software RAID 1 configuration (2x250 GB disks which appeared as one disk), setup on the Dell Poweredge T110 (which meets compatibility requirements) without requiring any extra setup from me. (As an aside I'm fairly sure it's software RAID, as we didn't spec a hardware RAID controller, if that's of any importance in this situation). I am now testing installing ESXi 5.0 on this server to run some VMs. I've successfully installed ESXi, and imported a VM fine, but it's showing 2 x 250 GB disks available as datastores. However they should be appearing as one volume. When I boot the server, there is a RAID configuration screen you can enter, and I'm guessing this is what I'll have to do at some stage, but now need to be very careful because there is one disk which contains data that I want to be mirrored on the other disk. What is the best thing to do in this situation?

    Read the article

  • What is the fastest RAID in practise?

    - by Luke
    I'm going to be rebuilding my server, and I want much faster access to my data. I've used RAID 1 and 0 in the past, and decided upon RAID 10 (dedicated RAID card). Then someone told me to use RAID 5+0, then someone else told me to use RAID 6+0. Assuming the Hardware RAID Card supports each level, what is currently the FASTEST RAID available, given x number of hard drives? Reliability is now another factor, and I am willing to spend money on new drives if a drive (or multiple) fail. I simply want to know what the fastest RAID level is, along with some reliability for recovering from a failure

    Read the article

  • raid md device is not remove from memory, how to overcome this problem

    - by santhosha
    i create raid 10 , i removed two arrays form md11 one by one , after that i going to editing the contents those are mounted ( it will be not responding stage), after i try for remove arrays those are left it is shows device or resource busy ( is not removed from memory). i try to terminate process this is also not work, i absorve from 4 days resync will be 8.0% it can not modifying. cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec mdadm -D /dev/md11 /dev/md11: Version : 00.90.03 Creation Time : Sun Jan 16 16:20:01 2011 Raid Level : raid10 Array Size : 286743936 (273.46 GiB 293.63 GB) Device Size : 143371968 (136.73 GiB 146.81 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 11 Persistence : Superblock is persistent Update Time : Sun Jan 16 16:56:07 2011 State : active, degraded, resyncing Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K Rebuild Status : 8% complete UUID : 5e124ea4:79a01181:dc4110d3:a48576ea Events : 0.23 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 4 8 145 2 faulty spare rebuilding /dev/sdj1 3 8 65 3 active sync /dev/sde1 umount /dev/md11 umount: /dev/md11: not mounted mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 kill -9 2128 kill -9 5018 kill -9 27605 kill -9 30562 kill -3 30591 mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec

    Read the article

  • format/build raid 5 with one 4k drive, three 512b

    - by skidawgz
    I have 4 WD 1TB drives which I want to 4x1TB Raid5. I am not sure what course of action to take next. How do I configure my 4th drive (sde) to align with the rest? Will this affect performance? I rcv this msg (which brings me here to ask these question): The device presents a logical sector size that is smaller than the physical sector size. Aligning to a physical sector (or optimal I/O) size boundary is recommended, or performance may be impacted. fdisk -l shows: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf324ba09 Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x38bcc1f0 Device Boot Start End Blocks Id System /dev/sdc1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x570f77e7 Device Boot Start End Blocks Id System /dev/sdd1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xeb665e7b Device Boot Start End Blocks Id System

    Read the article

  • How to access a fake raid?

    - by maaartinus
    I have a fake raid, which I wanted to access using mdadm /dev/md0 -A -c 128 -l stripe --verbose /dev/sda /dev/sdc which should be right, as far as I understand the man page. But I get the message mdadm: option -l not valid in assemble mode leaving the offending option out leads to mdadm: failed to create /dev/md0 and (despite verbose) no more information. I'm assuming that -A requires some mdadm-specific header which is obviously missing. I probably need to use "build" instead of assemble, but from the description I'm really unsure whether this is a non-destructive operation. Is it? What should I exactly do? UPDATE I see I haven't made clear, that the array already exists as a fake-raid (I can't give the details about my mainboard now). It looks like doing nothing except for interleaving blocks, so I hoped it could be easily done using mdadm, too. Maybe I'm completely wrong, but all the info I've found was concerned with booting from fake-raid, what I don't really need. I'd be happy with a read access for now.

    Read the article

  • Installing 10.04 server on HP xw9400 Workstation with RAID 5

    - by Dave Long
    I have a workstation that was given to me that is a friggen powerhouse, so I figured I would set it up as my development and demo server. This is my first experience installing Ubuntu onto a RAID array and so far it has not been a fun one. I have been following the Advanced Installation guide for installing Ubuntu 10.04 server, and it says that there will be an option on the Partition Disks screen to manually create the partitions, but the only options I have are: Configure iSCSI volumes Undo changes to partitions Finish partitioning and write changes to disk Just before I got to that screen I got a message that said: One or more drives containing Serial ATA RAID configurations have been found. Do you wish to activate these RAID devices? It doesn't matter whether I answer yes or no to that, I still get the same Partition Disks screen. When I try to select Finish partitioning and write changes to disk I just get the No root file system error. Has anyone else experienced this, and how do I get past it? Can I not run Ubuntu on this machine?

    Read the article

  • recovering raid 0 hard disk

    - by Hiawatha
    I bumped to a huge (for me) problem. I was running dual boot system (win 7 / linux) and at some point I decided to test fedora ( I am new in Linux ). My hard disk conf: 3 hard disks each 1 TB, 2 set to raid 0 with windows running on it and 1 for linux. After installing it from live usb I found out that windows 7 is not in grub anymore and while booting shows raid error. I installed back Ubuntu and ran Disk Utility and checked now I have one disks (raid 0) failed (READ) error. First has 5 bad sectors and second has 1 bad sector. And now I dont know what to do and how to repair. further I dont know which data i could provide to get help. I tried ntfsfix and got this output: Mounting volume... NTFS signature is missing. FAILED Attempting to correct errors... NTFS signature is missing. FAILED Failed to startup volume: Invalid argument NTFS signature is missing. Trying the alternate boot sector Unrecoverable error Volume is corrupt. You should run chkdsk. #sudo ntfs-3g -o force,rw /dev/sdb /media/windows NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around?

    Read the article

  • Failed to install GRUB on a separate '/boot' partition on a fake RAID 0 (12.04LTS)

    - by gerben
    I'm having some problems getting GRUB configured for Ubuntu 12.04LTS on a fake RAID 0. I can either get the GRUB rescue prompt at startup, or just a GRUB prompt but I cannot boot to Ubuntu manually. How can I configure the GRUB to actually use the Ubuntu install? The steps taken: Installing Ubuntu on fake raid The Ubuntu installer cannot install Ubuntu on the drive. After defining the partitions to use it fails with "Error: ???", pressing OK terminates the installer. Therefore, I used GParted to configure the partitions: /dev/mapper/sil_agadaccfacbg : (the RAID configuration, created partition): /dev/mapper/sil_agadaccfacbg1:ext2, 200MiB, (with 'boot' flag) /dev/mapper/sil_agadaccfacbg3:ext2, 67.75GiB, (which will contain Ubuntu) /dev/mapper/sil_agadaccfacbg2:extended, 1.00GiB, (for swap) Contains: /dev/mapper/sil_agadaccfacbg5: unknown Because of the fake-RAID, I already mounted the destination partitions before running the Ubuntu installer: > mkdir /mnt/boot > sudo mount /dev/mapper/sil_agadaccfacbg1 /mnt/boot > mkdir /mnt/ubuntu > sudo mount /dev/mapper/sil_agadaccfacbg3 /mnt/ubuntu In the installer I chose the following partition usage: /dev/mapper/sil_agadaccfacbg1 ext2, mount at /boot (209MB) /dev/mapper/sil_agadaccfacbg3 ext2, mount at / (72751MB) /dev/mapper/sil_agadaccfacbg5 swap Device for boot loader installation: /dev/mapper/sil_agadaccfacbg, linux device-mapper (striped) (74.0GB) This will install Ubuntu, but will fail to install GRUB (it seems to use /dev/sda no matter which one I choose) Installing GRUB with dpkg-reconfigure I followed this guide, but adapted it for two partitions: sudo mount /dev/mapper/sil_agadaccfacbg3 /mnt/ubuntu sudo mount --bind /dev /mnt/ubuntu/dev sudo mount --bind /proc /mnt/ubuntu/proc sudo mount --bind /sys /mnt/ubuntu/sys sudo mount /dev/mapper/sil_agadaccfacbg1 /mnt/boot sudo mount --bind /boot /mnt/boot sudo chroot /mnt/ubuntu dpkg-reconfigure grub-pc However, it does not ask where to install GRUB (I should choose /dev/mapper/sil_agadaccfacbg somewhere..) After reboot I get the GRUB rescue prompt with message no such device Installing GRUB with grub-install After the same mount commands as above, I continued with: > sudo grub-install --root-directory=/mnt/boot /dev/mapper/sil_agadaccfacbg This gives the following message: /usr/sbin/grub-probe: error: cannot find a device for /mnt/boot/boot/grub (is /dev mounted?) It does succeed when mounting just the boot partition : sudo mount /dev/mapper/sil_agadaccfacbg1 /mnt sudo grub-install --root-directory=/mnt/ /dev/mapper/sil_agadaccfacbg This finishes with: Installation finished. No error reported. After reboot I get the GRUB console, with welcome text. Attempting to manually start Ubuntu: ls (hd0) (hd0,msdos3) : (Ubuntu install partition) (hd0,msdos1) : (Ubuntu boot partition) (hd1) (hd1,msdos1) : (Ubuntu live USB) ls (hd0,msdos3)/ contains: - vmlinuz - lib/ - tmp/ - initrd.img - mnt/ - var/ - proc/ - boot/ - root/ - etc/ - run/ - media/ - sbin/ - bin/ - selinux/ - dev/ - srv/ - home/ - sys/ ls (hd0,msdos1)/ contains: -grub/ -boot/ -initrd.img-3.8.0-29-generic -vmlinuz-3.8.0.29-generic -config-3.8 linux (hd0,msdos3)/vmlinuz This returns "error: out of disk" Installing GRUB on Ubuntu partition with grub-install > sudo mount /dev/mapper/sil_agadaccfacbg3 /mnt > sudo grub-install --root-directory=/mnt/ /dev/mapper/sil_agadaccfacbg This finishes with message: > Installation finished. No error reported. After reboot get the message "error: out of disk" and the GRUB rescue prompt. Configuring GRUB with grub-mkconfig Attempting to run grub-mkconfig with different destinations results in the same message: /usr/sbin/grub-probe: error: cannot find a device for / (is /dev mounted?). Remarks: Initially I didn't use a separate /boot partition, but the GRUB install then also failed. Because some mention that a small partition at the beginning of the drive is necessary on old machines, I retried with a /boot partition This is a single boot (no other OS's installed/used)

    Read the article

  • Reconstructing the disk order in RAID 6 with 7 disks

    - by rkotulla
    a little background to this question first: I am running a RAID-6 within a QNAP TS869L external RAID/NAS system. I started with 5 disks of 3 TB each back in the day, and later added another 2 disks of 3TB to the RAID. The QNAP internals handled the growing and re-syncing etc, and everything seemd to be perfectly fine. About 2 weeks ago, I had one of the disks (disk #5, disk #2 has gone bad in the mean time) fail, and somehow (I have no idea why), also disks 1 and 2 got kicked out of the array. I replaced disk #5, but the RAID didn't start working again. After some calls to QNAP technical support, they re-created the array (using mdadm --create --force --assume-clean ...), but the resulting array couldn't find a filesystem, and I was kindly referred to contact a data recovery company that I can't afford. After some digging through old log files, resetting the disk to factory default, etc, I found a few errors that were made during this re-create - I wish I still had some of the original metadata, but unfortunately i don't (I definitely learned that lesson). I'm currently at the point where I know the correct chunk-size (64K), metadata-version (1.0; factory default was 0.9, but from what I read 0.9 doesn't handle disks over 2 TB, mine are 3 TB), and I now find the ext4 filesystem that should be on the disks. Only variable left to determine is the right disk order! I started using the description found in answer #4 of "Recover RAID 5 data after created new array instead of re-using" but am a little confused on what the order should be for a proper RAID-6. RAID-5 is pretty well documented in a number of places, but RAID-6 much less so. Also, does the layout, i.e. distribution of parity and data chunks across the disks, change after the growing of the array from 5 to 7 disks, or does the re-sync re-organize them in such a way a native 7-disk RAID-6 would have been? Thanks some more mdadm output that might be helpful: mdadm version: [~] # mdadm --version mdadm - v2.6.3 - 20th August 2007 mdadm details from one of the disks in the array: [~] # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 1.0 Feature Map : 0x0 Array UUID : 1c1614a5:e3be2fbb:4af01271:947fe3aa Name : 0 Creation Time : Tue Jun 10 10:27:58 2014 Raid Level : raid6 Raid Devices : 7 Used Dev Size : 5857395112 (2793.02 GiB 2998.99 GB) Array Size : 29286975360 (13965.12 GiB 14994.93 GB) Used Size : 5857395072 (2793.02 GiB 2998.99 GB) Super Offset : 5857395368 sectors State : clean Device UUID : 7c572d8f:20c12727:7e88c888:c2c357af Update Time : Tue Jun 10 13:01:06 2014 Checksum : d275c82d - correct Events : 7036 Chunk Size : 64K Array Slot : 0 (0, 1, failed, 3, failed, 5, 6) Array State : Uu_u_uu 2 failed mdadm details for the array in the current disk-order (based on my best guess reconstructed from old log-files) [~] # mdadm --detail /dev/md0 /dev/md0: Version : 01.00.03 Creation Time : Tue Jun 10 10:27:58 2014 Raid Level : raid6 Array Size : 14643487680 (13965.12 GiB 14994.93 GB) Used Dev Size : 2928697536 (2793.02 GiB 2998.99 GB) Raid Devices : 7 Total Devices : 5 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Jun 10 13:01:06 2014 State : clean, degraded Active Devices : 5 Working Devices : 5 Failed Devices : 0 Spare Devices : 0 Chunk Size : 64K Name : 0 UUID : 1c1614a5:e3be2fbb:4af01271:947fe3aa Events : 7036 Number Major Minor RaidDevice State 0 8 3 0 active sync /dev/sda3 1 8 19 1 active sync /dev/sdb3 2 0 0 2 removed 3 8 51 3 active sync /dev/sdd3 4 0 0 4 removed 5 8 99 5 active sync /dev/sdg3 6 8 83 6 active sync /dev/sdf3 output from /proc/mdstat (md8, md9, and md13 are internally used RAIDs holding swap, etc; the one I'm after is md0) [~] # more /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md0 : active raid6 sdf3[6] sdg3[5] sdd3[3] sdb3[1] sda3[0] 14643487680 blocks super 1.0 level 6, 64k chunk, algorithm 2 [7/5] [UU_U_UU] md8 : active raid1 sdg2[2](S) sdf2[3](S) sdd2[4](S) sdc2[5](S) sdb2[6](S) sda2[1] sde2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdg4[3] sdf4[4] sde4[5] sdd4[6] sdc4[2] sdb4[1] sda4[0] 458880 blocks [8/7] [UUUUUUU_] bitmap: 21/57 pages [84KB], 4KB chunk md9 : active raid1 sdg1[6] sdf1[5] sde1[4] sdd1[3] sdc1[2] sda1[0] sdb1[1] 530048 blocks [8/7] [UUUUUUU_] bitmap: 37/65 pages [148KB], 4KB chunk unused devices: <none>

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >