Search Results

Search found 426 results on 18 pages for 'scsi'.

Page 5/18 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Error 5 partition table invalid or corrupt

  - by Clodoaldo

  I'm trying to add a second SSD to a Centos 6 system. But I get the Error 5 partition table invalid or corrupt at boot. The system already has a single SSD (sdb) and a pair of HDDs (sd{a,c}) in a RAID 1 array from where it boots. It is as if the new SSD assumes one of the devices of the RAID array. Is it? How to avoid that or rearrange the setup? # cat fstab UUID=967b4035-782d-4c66-b22f-50244fe970ca / ext4 defaults 1 1 UUID=86fd06e9-cdc9-4166-ba9f-c237cfc43e02 /boot ext4 defaults 1 2 UUID=72552a7a-d8ae-4f0a-8917-b75a6239ce9f /ssd ext4 discard,relatime 1 2 UUID=8000e5e6-caa2-4765-94f8-9caeb2bda26e swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 # ll /dev/disk/by-id/ total 0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:0 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:1 -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:2 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a04d7241:8da6023e:f9004352:107a923a -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a22c43b9:f1954990:d3ddda5e:f9aff3c9 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-f403a2d0:447803b5:66edba73:569f8305 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c500383621ff -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c5003838b2e7 -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5e83a97f592139d6 -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5e83a97f592139d6-part1 -> ../../sdb1 # fdisk -l Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x79298ec9 Device Boot Start End Blocks Id System /dev/sdb1 1 14594 117219328 83 Linux Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d99de Device Boot Start End Blocks Id System /dev/sdc1 1 1275 10240000 fd Linux raid autodetect /dev/sdc2 * 1275 1339 512000 fd Linux raid autodetect /dev/sdc3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b3327 Device Boot Start End Blocks Id System /dev/sda1 1 1275 10240000 fd Linux raid autodetect /dev/sda2 * 1275 1339 512000 fd Linux raid autodetect /dev/sda3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/md0: 10.5 GB, 10484641792 bytes 2 heads, 4 sectors/track, 2559727 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md2: 489.1 GB, 489095557120 bytes 2 heads, 4 sectors/track, 119408095 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1: 524 MB, 524275712 bytes 2 heads, 4 sectors/track, 127997 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table # cat /etc/grub.conf default=0 timeout=5 splashimage=(hd2,1)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.32-220.17.1.el6.x86_64) root (hd2,1) kernel /vmlinuz-2.6.32-220.17.1.el6.x86_64 ro root=UUID=967b4035-782d-4c66-b22f-50244fe970ca rd_MD_UUID=f403a2d0:447803b5:66edba73:569f8305 rd_MD_UUID=a22c43b9:f1954990:d3ddda5e:f9aff3c9 rd_NO_LUKS rd_NO_LVM rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=br-abnt2 crashkernel=auto rhgb quiet initrd /initramfs-2.6.32-220.17.1.el6.x86_64.img

  Read the article

• Error 22 no such partition on adding a SSD

  - by Clodoaldo

  I'm trying to add a second SSD to a Centos 6 system. But I get the error 22 no such partition at boot. The system already has a single SSD (sdb) and a pair of HDDs (sd{a,c}) in a RAID 1 array from where it boots. It is as if the new SSD assumes one of the devices of the RAID array. Is it? How to avoid that or rearrange the setup? # cat fstab UUID=967b4035-782d-4c66-b22f-50244fe970ca / ext4 defaults 1 1 UUID=86fd06e9-cdc9-4166-ba9f-c237cfc43e02 /boot ext4 defaults 1 2 UUID=72552a7a-d8ae-4f0a-8917-b75a6239ce9f /ssd ext4 discard,relatime 1 2 UUID=8000e5e6-caa2-4765-94f8-9caeb2bda26e swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 # ll /dev/disk/by-id/ total 0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:0 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:1 -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:2 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a04d7241:8da6023e:f9004352:107a923a -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a22c43b9:f1954990:d3ddda5e:f9aff3c9 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-f403a2d0:447803b5:66edba73:569f8305 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c500383621ff -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c5003838b2e7 -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5e83a97f592139d6 -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5e83a97f592139d6-part1 -> ../../sdb1 # fdisk -l Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x79298ec9 Device Boot Start End Blocks Id System /dev/sdb1 1 14594 117219328 83 Linux Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d99de Device Boot Start End Blocks Id System /dev/sdc1 1 1275 10240000 fd Linux raid autodetect /dev/sdc2 * 1275 1339 512000 fd Linux raid autodetect /dev/sdc3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b3327 Device Boot Start End Blocks Id System /dev/sda1 1 1275 10240000 fd Linux raid autodetect /dev/sda2 * 1275 1339 512000 fd Linux raid autodetect /dev/sda3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/md0: 10.5 GB, 10484641792 bytes 2 heads, 4 sectors/track, 2559727 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md2: 489.1 GB, 489095557120 bytes 2 heads, 4 sectors/track, 119408095 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1: 524 MB, 524275712 bytes 2 heads, 4 sectors/track, 127997 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table # cat /etc/grub.conf default=0 timeout=5 splashimage=(hd2,1)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.32-220.17.1.el6.x86_64) root (hd2,1) kernel /vmlinuz-2.6.32-220.17.1.el6.x86_64 ro root=UUID=967b4035-782d-4c66-b22f-50244fe970ca rd_MD_UUID=f403a2d0:447803b5:66edba73:569f8305 rd_MD_UUID=a22c43b9:f1954990:d3ddda5e:f9aff3c9 rd_NO_LUKS rd_NO_LVM rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=br-abnt2 crashkernel=auto rhgb quiet initrd /initramfs-2.6.32-220.17.1.el6.x86_64.img

  Read the article

• External USB drive is failing

  - by dma_k

  I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

  Read the article

• How to install Huawei Mobile broadband EC306?

  - by serviteur

  How to install Huawei Mobile Broadband EC 306 EVDO RevB in Ubuntu 12.04 LTS 64bit ? Best Regards Excuses me for my bad english When I connect the modem on ubuntu, it fails to mount system and furthermore it is not recognized as a CD-ROM. I is not installed Windows on my computer, but I try to open the modem under Windows on a PC friend, There is no script file called "Linux", but only Windows. lsusb : serviteur@creation:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 15d9:0a4c Trust International B.V. USB+PS/2 Optical Mouse Bus 001 Device 007: ID 12d1:1506 Huawei Technologies Co., Ltd. E398 LTE/UMTS/GSM Modem/Networkcard dmesg Q: 0 ANSI: 2 [16619.060771] sr1: scsi-1 drive [16619.060955] sr 13:0:0:0: Attached scsi CD-ROM sr1 [16619.061099] sr 13:0:0:0: Attached scsi generic sg3 type 5 [16619.061358] sd 14:0:0:0: Attached scsi generic sg4 type 0 [16619.063654] sd 14:0:0:0: [sdc] Attached SCSI removable disk [16634.224923] usb 1-6: USB disconnect, device number 6 [16638.468041] usb 1-6: new high-speed USB device number 7 using ehci_hcd [16638.586210] option 1-6:1.0: GSM modem (1-port) converter detected [16638.586316] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB0 [16638.586435] option 1-6:1.1: GSM modem (1-port) converter detected [16638.586517] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB1 [16638.586607] option 1-6:1.2: GSM modem (1-port) converter detected [16638.586676] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB2 [16638.586752] option 1-6:1.3: GSM modem (1-port) converter detected [16638.586828] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB3 [16638.586929] option 1-6:1.4: GSM modem (1-port) converter detected [16638.586997] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB4 [16638.587114] option 1-6:1.5: GSM modem (1-port) converter detected [16638.587187] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB5 [16638.646686] option1 ttyUSB5: GSM modem (1-port) converter now disconnected from ttyUSB5 [16638.646706] option 1-6:1.5: device disconnected [16638.660755] scsi15 : usb-storage 1-6:1.5 [16638.663284] option1 ttyUSB4: GSM modem (1-port) converter now disconnected from ttyUSB4 [16638.663301] option 1-6:1.4: device disconnected [16638.689043] scsi16 : usb-storage 1-6:1.4

  Read the article

• Should Exterrnal USB hard drive auto mount Ubuntu 12.04.01 LTS

  - by Chris Good

  I want to have external USB hard drives automatically mounted when plugged in. I have 2 drives exactly the same except for volume label. They both have the same UUID. I want to be easily able to swap them as I'm using them for backups and want to keep 1 at home for off site backup. I've set up the /etc/fstab so they should mount at different places based on their volume label: /etc/fstab : LABEL=Passport1 /media/Passport1 ntfs defaults,windows_names,locale=en_US.utf8 0 0 LABEL=Passport2 /media/Passport2 ntfs defaults,windows_names,locale=en_US.utf8 0 0 blkid shows : ... /dev/sdc1: LABEL="Passport2" UUID="4E1AEA7B1AEA6007" TYPE="ntfs" /dev/sdd1: LABEL="Passport1" UUID="4E1AEA7B1AEA6007" TYPE="ntfs" They both mount automatically during reboot but do not mount when just plugged in to a running system. I've read lots of stuff about this, much of it is old so I'm not sure if it applies. I've read some stuff that says the mounts should happen automatically when plugged in, and lots of other stuff that says you have to install other software to make this happen, although much of it just seems to set up the fstab. What's the real story? Here is /var/log/syslog when drive is plugged in: Dec 14 11:22:58 ausyvutims1 kernel: [66221.300196] usb 1-1: new high-speed USB device number 6 using ehci_hcd Dec 14 11:22:58 ausyvutims1 mtp-probe: checking bus 1, device 6: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1" Dec 14 11:22:58 ausyvutims1 mtp-probe: bus: 1, device: 6 was not an MTP device Dec 14 11:22:58 ausyvutims1 kernel: [66221.656020] scsi7 : usb-storage 1-1:1.0 Dec 14 11:22:59 ausyvutims1 kernel: [66222.661534] scsi 7:0:0:0: Direct-Access WD My Passport 0748 1016 PQ: 0 ANSI: 6 Dec 14 11:22:59 ausyvutims1 kernel: [66222.666466] scsi 7:0:0:1: Enclosure WD SES Device 1016 PQ: 0 ANSI: 6 Dec 14 11:22:59 ausyvutims1 kernel: [66222.667739] sd 7:0:0:0: Attached scsi generic sg3 type 0 Dec 14 11:22:59 ausyvutims1 kernel: [66222.667913] ses 7:0:0:1: Attached Enclosure device Dec 14 11:22:59 ausyvutims1 kernel: [66222.668047] ses 7:0:0:1: Attached scsi generic sg4 type 13 Dec 14 11:22:59 ausyvutims1 kernel: [66222.678473] sd 7:0:0:0: [sdc] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB) Dec 14 11:22:59 ausyvutims1 kernel: [66222.687700] sd 7:0:0:0: [sdc] Write Protect is off Dec 14 11:22:59 ausyvutims1 kernel: [66222.687705] sd 7:0:0:0: [sdc] Mode Sense: 47 00 10 08 Dec 14 11:22:59 ausyvutims1 kernel: [66222.701076] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.701081] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.738062] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.738068] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.754558] sdc: sdc1 Dec 14 11:22:59 ausyvutims1 kernel: [66222.792006] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.792012] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.792016] sd 7:0:0:0: [sdc] Attached SCSI disk Dec 14 11:22:59 ausyvutims1 ata_id[16971]: HDIO_GET_IDENTITY failed for '/dev/sdc': Invalid argument Thanks for any help offered

  Read the article

• Unity not Working 14.04

  - by Back.Slash

  I am using Ubuntu 14.04 LTS x64. I did a sudo apt-get upgrade yesterday and restarted my PC. Now my taskbar and panel are missing. When I try to restart Unity using unity --replace Then I get error: unity-panel-service stop/waiting compiz (core) - Info: Loading plugin: core compiz (core) - Info: Starting plugin: core unity-panel-service start/running, process 3906 compiz (core) - Info: Loading plugin: ccp compiz (core) - Info: Starting plugin: ccp compizconfig - Info: Backend : gsettings compizconfig - Info: Integration : true compizconfig - Info: Profile : unity compiz (core) - Info: Loading plugin: composite compiz (core) - Info: Starting plugin: composite compiz (core) - Info: Loading plugin: opengl compiz (core) - Info: Unity is fully supported by your hardware. compiz (core) - Info: Unity is fully supported by your hardware. compiz (core) - Info: Starting plugin: opengl libGL error: dlopen /usr/lib/x86_64-linux-gnu/dri/i965_dri.so failed (/usr/lib/x86_64-linux-gnu/dri/i965_dri.so: undefined symbol: _glapi_tls_Dispatch) libGL error: dlopen ${ORIGIN}/dri/i965_dri.so failed (${ORIGIN}/dri/i965_dri.so: cannot open shared object file: No such file or directory) libGL error: dlopen /usr/lib/dri/i965_dri.so failed (/usr/lib/dri/i965_dri.so: cannot open shared object file: No such file or directory) libGL error: unable to load driver: i965_dri.so libGL error: driver pointer missing libGL error: failed to load driver: i965 libGL error: dlopen /usr/lib/x86_64-linux-gnu/dri/swrast_dri.so failed (/usr/lib/x86_64-linux-gnu/dri/swrast_dri.so: undefined symbol: _glapi_tls_Dispatch) libGL error: dlopen ${ORIGIN}/dri/swrast_dri.so failed (${ORIGIN}/dri/swrast_dri.so: cannot open shared object file: No such file or directory) libGL error: dlopen /usr/lib/dri/swrast_dri.so failed (/usr/lib/dri/swrast_dri.so: cannot open shared object file: No such file or directory) libGL error: unable to load driver: swrast_dri.so libGL error: failed to load driver: swrast compiz (core) - Info: Loading plugin: compiztoolbox compiz (core) - Info: Starting plugin: compiztoolbox compiz (core) - Info: Loading plugin: decor compiz (core) - Info: Starting plugin: decor compiz (core) - Info: Loading plugin: vpswitch compiz (core) - Info: Starting plugin: vpswitch compiz (core) - Info: Loading plugin: snap compiz (core) - Info: Starting plugin: snap compiz (core) - Info: Loading plugin: mousepoll compiz (core) - Info: Starting plugin: mousepoll compiz (core) - Info: Loading plugin: resize compiz (core) - Info: Starting plugin: resize compiz (core) - Info: Loading plugin: place compiz (core) - Info: Starting plugin: place compiz (core) - Info: Loading plugin: move compiz (core) - Info: Starting plugin: move compiz (core) - Info: Loading plugin: wall compiz (core) - Info: Starting plugin: wall compiz (core) - Info: Loading plugin: grid compiz (core) - Info: Starting plugin: grid compiz (core) - Info: Loading plugin: regex compiz (core) - Info: Starting plugin: regex compiz (core) - Info: Loading plugin: imgpng compiz (core) - Info: Starting plugin: imgpng compiz (core) - Info: Loading plugin: session compiz (core) - Info: Starting plugin: session I/O warning : failed to load external entity "/home/sumeet/.compiz/session/10de541a813cc1a8fc140170575114755000000020350005" compiz (core) - Info: Loading plugin: gnomecompat compiz (core) - Info: Starting plugin: gnomecompat compiz (core) - Info: Loading plugin: animation compiz (core) - Info: Starting plugin: animation compiz (core) - Info: Loading plugin: fade compiz (core) - Info: Starting plugin: fade compiz (core) - Info: Loading plugin: unitymtgrabhandles compiz (core) - Info: Starting plugin: unitymtgrabhandles compiz (core) - Info: Loading plugin: workarounds compiz (core) - Info: Starting plugin: workarounds compiz (core) - Info: Loading plugin: scale compiz (core) - Info: Starting plugin: scale compiz (core) - Info: Loading plugin: expo compiz (core) - Info: Starting plugin: expo compiz (core) - Info: Loading plugin: ezoom compiz (core) - Info: Starting plugin: ezoom compiz (core) - Info: Loading plugin: unityshell compiz (core) - Info: Starting plugin: unityshell WARN 2014-06-02 18:46:23 unity.glib.dbus.server GLibDBusServer.cpp:579 Can't register object 'org.gnome.Shell' yet as we don't have a connection, waiting for it... ERROR 2014-06-02 18:46:23 unity.debug.interface DebugDBusInterface.cpp:216 Unable to load entry point in libxpathselect: libxpathselect.so.1.4: cannot open shared object file: No such file or directory compiz (unityshell) - Error: GL_ARB_vertex_buffer_object not supported ERROR 2014-06-02 18:46:23 unity.shell.compiz unityshell.cpp:3850 Impossible to delete the unity locked stamp file compiz (core) - Error: Plugin initScreen failed: unityshell compiz (core) - Error: Failed to start plugin: unityshell compiz (core) - Info: Unloading plugin: unityshell X Error of failed request: BadWindow (invalid Window parameter) Major opcode of failed request: 3 (X_GetWindowAttributes) Resource id in failed request: 0x3e000c9 Serial number of failed request: 10115 Current serial number in output stream: 10116 Any help would be highly appreciated. EDIT : My PC configuration description: Portable Computer product: Dell System XPS L502X (System SKUNumber) vendor: Dell Inc. version: 0.1 serial: 1006ZP1 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: administrator_password=unknown boot=normal chassis=portable family=HuronRiver System frontpanel_password=unknown keyboard_password=unknown power-on_password=unknown sku=System SKUNumber uuid=44454C4C-3000-1030-8036-B1C04F5A5031 *-core description: Motherboard product: 0YR8NN vendor: Dell Inc. physical id: 0 version: A00 serial: .1006ZP1.CN4864314C0560. slot: Part Component *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A11 date: 05/29/2012 size: 128KiB capacity: 2496KiB capabilities: pci pnp upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy360 int13floppy1200 int13floppy720 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot smartbattery biosbootspecification netboot *-cpu description: CPU product: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz vendor: Intel Corp. physical id: 19 bus info: cpu@0 version: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz serial: Not Supported by CPU slot: CPU size: 800MHz capacity: 800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts nopl xtopology nonstop_tsc aperfmperf eagerfpu pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=4 threads=8 *-cache:0 description: L1 cache physical id: 1a slot: L1-Cache size: 64KiB capacity: 64KiB capabilities: synchronous internal write-through data *-cache:1 description: L2 cache physical id: 1b slot: L2-Cache size: 256KiB capacity: 256KiB capabilities: synchronous internal write-through data *-cache:2 description: L3 cache physical id: 1c slot: L3-Cache size: 6MiB capacity: 6MiB capabilities: synchronous internal write-back unified *-memory description: System Memory physical id: 1d slot: System board or motherboard size: 6GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: M471B5273DH0-CH9 vendor: Samsung physical id: 0 serial: 450F1160 slot: ChannelA-DIMM0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 1 serial: 0CA0E8E2 slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:3000(size=4096) memory:f0000000-f10fffff ioport:c0000000(size=301989888) *-generic UNCLAIMED description: Unassigned class product: Illegal Vendor ID vendor: Illegal Vendor ID physical id: 0 bus info: pci@0000:01:00.0 version: ff width: 32 bits clock: 66MHz capabilities: bus_master vga_palette cap_list configuration: latency=255 maxlatency=255 mingnt=255 resources: memory:f0000000-f0ffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:3000(size=128) memory:f1000000-f107ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:52 memory:f1400000-f17fffff memory:e0000000-efffffff ioport:4000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei_me latency=0 resources: irq:50 memory:f1c05000-f1c0500f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:16 memory:f1c09000-f1c093ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:53 memory:f1c00000-f1c03fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode cap_list configuration: driver=pcieport resources: irq:16 *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 memory:f1b00000-f1bfffff *-network description: Wireless interface product: Centrino Wireless-N 1030 [Rainbow Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 34 serial: bc:77:37:14:47:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-27-generic firmware=18.168.6.1 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:f1b00000-f1b01fff *-pci:3 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:19 memory:f1a00000-f1afffff *-usb description: USB controller product: uPD720200 USB 3.0 Host Controller vendor: NEC Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:19 memory:f1a00000-f1a01fff *-pci:4 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 5 vendor: Intel Corporation physical id: 1c.4 bus info: pci@0000:00:1c.4 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 memory:f1900000-f19fffff *-pci:5 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 6 vendor: Intel Corporation physical id: 1c.5 bus info: pci@0000:00:1c.5 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 ioport:2000(size=4096) ioport:f1800000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 06 serial: 14:fe:b5:a3:ac:40 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=172.19.167.151 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:49 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:23 memory:f1c08000-f1c083ff *-isa description: ISA bridge product: HM67 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: driver=lpc_ich latency=0 resources: irq:0 *-ide:0 description: IDE interface product: 6 Series/C200 Series Chipset Family 4 port SATA IDE Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 05 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:40b8(size=8) ioport:40cc(size=4) ioport:40b0(size=8) ioport:40c8(size=4) ioport:4090(size=16) ioport:4080(size=16) *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:f1c04000-f1c040ff ioport:efa0(size=32) *-ide:1 description: IDE interface product: 6 Series/C200 Series Chipset Family 2 port SATA IDE Controller vendor: Intel Corporation physical id: 1f.5 bus info: pci@0000:00:1f.5 version: 05 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:40a8(size=8) ioport:40c4(size=4) ioport:40a0(size=8) ioport:40c0(size=4) ioport:4070(size=16) ioport:4060(size=16) *-scsi:0 physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: SAMSUNG HN-M640M physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 2AR1 serial: S2T3J1KBC00006 size: 596GiB (640GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=6b746d91 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: 0272-3e7f size: 348MiB capacity: 350MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2013-09-18 12:20:45 filesystem=ntfs label=System Reserved modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 116GiB capacity: 116GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 6037MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 110GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered state=mounted *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 logical name: /media/os version: 3.1 serial: 4e7853ec-5555-a74d-82e0-9f49798d3772 size: 156GiB capacity: 156GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2013-09-19 09:19:00 filesystem=ntfs label=OS mount.fstype=fuseblk mount.options=ro,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 state=mounted *-volume:3 description: Windows NTFS volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 logical name: /media/data version: 3.1 serial: 7666d55f-e1bf-e645-9791-2a1a31b24b9a size: 322GiB capacity: 322GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2013-09-17 23:27:01 filesystem=ntfs label=Data modified_by_chkdsk=true mount.fstype=fuseblk mount.options=rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 mounted_on_nt4=true resize_log_file=true state=mounted upgrade_on_mount=true *-scsi:1 physical id: 2 logical name: scsi1 capabilities: emulated *-cdrom description: DVD-RAM writer product: DVD+-RW GT32N vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/sr0 version: A201 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-battery product: DELL vendor: SANYO physical id: 1 version: 2008 serial: 1.0 slot: Rear capacity: 57720mWh configuration: voltage=11.1V `

  Read the article

• AIX: iscsi volumes disappear after reboot

  - by Dan

  We have an IBM P505 AIX box, with two internal disks and a defined iSCSI volume. The iSCSI volume is defined in it's own volume group, and is connected to an IBM iSCSI DS3300 disk array via the secondary onboard ethernet port (ie, we're not using a dedicated HBA, we're using the second onboard ethernet port for iSCSI exclusively.) When we reboot the AIX box, the iSCSI volume doesn't get mounted (which is fine; I've figured out that it fails to mount because AIX tries mounting it's volumes before starting the networking stack.) The problem is, after the server has booted it fails to redetect the iSCSI target as a physical disk. This means the volume group (iscsivg) can't go online. if I run cfgmgr -v to redetect the iscsi volume it successfully detects the iscsi target volume and creates a physical volume reference, but allocates it a different volume ID to what was defined before. eg - rootvg contains hdisk 0 and 1 iscsivg was originally defined with hdisk2 as the physical iSCSI volume. after reboot and running cfgmgr -v, AIX detects physical volumes hdisk0, hdisk11 and hdisk3. As there's no hdisk2, I can't varyon the iscsivg volume group. I can't seem any existing hdisk2 definition in the ODM. I can't easily add or change the definition of the physcial disk in the iscsivg volume group as it won't "varyon". Exporting the volume group deletes it completely, recreating the volume group by "importing" it from the reallocated disk makes it available again, but surely there's a better way? Can I force a specific hdisk drive designation for an iscsi target? How do you bring online iSCSI volumes after a reboot? I assume this "just works" with a dedicated HBA instead of a generic ethernet adapter? By the way, the iSCSI volume works fine once it's mounted; we only have problems getting it working - and only with AIX. The iSCSI array works fine with our Linux and Windows servers; ie the volumes get detected and remounted after boot time without any problems, using generic ethernet adapters. Here's some of the config from the AIX box: defined disks / devices: # lsdev hdisk0 Available 06-08-01-5,0 16 Bit LVD SCSI Disk Drive hdisk1 Available 06-08-01-8,0 16 Bit LVD SCSI Disk Drive hdisk3 Available Other iSCSI Disk Drive iscsi0 Available iSCSI Protocol Device scsi0 Available 06-08-00 PCI-X Dual Channel Ultra320 SCSI Adapter bus scsi1 Available 06-08-01 PCI-X Dual Channel Ultra320 SCSI Adapter bus ses0 Available 06-08-01-15,0 SCSI Enclosure Services Device sisscsia0 Available 06-08 PCI-X Dual Channel Ultra320 SCSI Adapter iscsi target definition in /etc/iscsi/targets: # IBM DS3300 disk array # port 1 on second controller 10.10.xx.xxx 3260 iqn.1992-01.com.lsi:1535.600a0b80005b0a7fxxxxxxxxxxxx physical volumes (after reimporting the volume group) # lspv hdisk0 0003b08a0d4936b6 rootvg active hdisk1 0003b08aaa5cb366 rootvg active hdisk3 0003b08a032d04bb iscsivg active

  Read the article

• MultiPath configuration on RHEL5 and Clariion CX-300

  - by Kamil Z

  I have problem with discovering my FC-connected CX-300 storage. Frankly speaking I'm complete novice in FibreChannel, so step by step explanation would be appreciated. My configuration consist of two IBM HS20 blades with RHEL5.4 on board and 2x Qlogic ISP2422-based 4Gb Fibre Channel HBAs on each blade. As a FC switch there are two Brocades built in BladeCenter Chassis, and finally there is EMC Clariion CX-300. CX300, and Brocade switches should be configured properly, because they were working fine with previous configuration, which main defference was RHEL3 instead RHEL5.4 Below there is my output from several usefull commands: #lspci | grep Fibre 06:01.0 FibreChannle: Qlogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) 06:01.1 FibreChannle: Qlogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) #lsmod | grep qla qla2xxx 1084741 0 scsi_transport_fc 37577 1 qla2xxx scsi_mod 141717 10 scsi_dh,qla2xxx,sg,scsi_transport_fc,usb_storage,libata,mptspi,mptscsih,scsi_transport_spi,sd_mod #cat /proc/scsi/scsi Attached Devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: LSILOGIC Model: 1030 IM IM Rev: 1000 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST936701LC FN Rev: B418 Type: Direct-Access ANSI SCSI revision: 04 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST936701LC FN Rev: B418 Type: Direct-Access ANSI SCSI revision: 04 I'd followed instructions from this site (editing /etc/multipath.conf), but i failed after multipath -ll - the output was empty. Do you have any suggestions about discovering FC Connected LUNs in such configuration?

  Read the article

• Why is this LTO4 Tape-drive not working

  - by Tim Haegele

  # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

  Read the article

• Disk operations freeze Debian

  - by Grzenio

  Hi, I have just installed Debian testing on my new desktop and I am not very happy with performance - when I perform a disk intensive operation, e.g. upgrade packages in the system, everything seems to freeze, e.g. changing tabs in Iceweasel takes 3 seconds. I run the Debian on my 3 year old Thinkpad X60 ultra-portable, and I don't have these issues. (every single parameter of the laptop is much worse than the desktop). I am using the default packaged kernel and scripts. I run hdparm -t /dev/sda1 And I got around 96GB/s, which is expected. What else can I try to make it work better? EDIT: grzes:/home/ga# hdparm -i /dev/sda /dev/sda: Model=WDC WD15EARS-00Z5B1, FwRev=80.00A80, SerialNo=WD-WMAVU1362357 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50 BuffType=unknown, BuffSize=unknown, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=2930277168 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6 AdvancedPM=no WriteCache=enabled Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7 * signifies the current active mode EDIT2: Even my wife said "on this new computer I can't do anything when I copy the photos from the camera and its much worse than on the old one". So it must be serious. EDIT3: Updated to 2.6.32, but still no improvement EDIT4: I forgot to mention that the new disk is ext4, the old was ext3. EDIT5: Still not solved. I have a P43 ASUS P5QL-E board. Lines from dmesg that seem relevant: [ 0.370850] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.370852] io scheduler noop registered [ 0.370853] io scheduler anticipatory registered [ 0.370854] io scheduler deadline registered [ 0.370876] io scheduler cfq registered (default) ... [ 0.908233] ata_piix 0000:00:1f.2: version 2.13 [ 0.908243] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.908246] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 0.908275] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 0.908316] scsi0 : ata_piix [ 0.908374] scsi1 : ata_piix [ 0.909180] ata1: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19 [ 0.909183] ata2: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19 [ 0.909199] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.909202] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] [ 0.909228] ata_piix 0000:00:1f.5: setting latency timer to 64 [ 0.909279] scsi2 : ata_piix [ 0.909326] scsi3 : ata_piix [ 0.910021] ata3: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa480 irq 19 [ 0.910024] ata4: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa488 irq 19 [ 0.915575] FDC 0 is a post-1991 82077 ... [ 1.716062] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.716074] ata1.01: SATA link down (SStatus 0 SControl 300) [ 1.724318] ata1.00: ATA-8: WDC WD15EARS-00Z5B1, 80.00A80, max UDMA/133 [ 1.724322] ata1.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 1.740339] ata1.00: configured for UDMA/133 [ 1.740428] scsi 0:0:0:0: Direct-Access ATA WDC WD15EARS-00Z 80.0 PQ: 0 ANSI: 5 [ 1.746788] scsi 6:0:0:0: CD-ROM ASUS DRW-1608P 1.17 PQ: 0 ANSI: 5 ... [ 1.925981] sd 0:0:0:0: [sda] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) [ 1.926005] sd 0:0:0:0: [sda] Write Protect is off [ 1.926007] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.926020] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.926092] sda:sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray [ 1.931106] Uniform CD-ROM driver Revision: 3.20 [ 1.931191] sr 6:0:0:0: Attached scsi CD-ROM sr0 ... [ 1.941936] sda1 sda2 sda3 sda4 < sda5 sda6 > [ 1.967691] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.970938] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.970959] sr 6:0:0:0: Attached scsi generic sg1 type 5 ... [ 2.500086] EXT4-fs (sda3): mounted filesystem with ordered data mode ... [ 7.150468] EXT4-fs (sda6): mounted filesystem with ordered data mode

  Read the article

• renaming hard drives (sdc to sdb) on the fly

  - by w00t

  ata2: link is slow to respond, please be patient (ready=0) kernel: [2761026.198796] ata2: soft resetting link kernel: [2761031.226669] ata2.00: disabled kernel: [2761031.226720] ata2: EH complete kernel: [2761031.226753] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK After receiving the error above, I couldn't access /dev/sdb anymore. Not wanting to restart the server, I rescanned for the device using echo "- - -" > /sys/class/scsi_host/host1/scan and it readded the drive as /dev/sdc. From what I have found, I need to use echo "scsi add-single-device 0 0 3 0" > /proc/scsi/scsi, "3" being the SCSI ID which corresponds to sdb. Everything nice up to the point I execute the command and get -bash: echo: write error: Invalid argument. All the solutions point to using this method, but I am unable to. Any other method available? Debian 5.0.8 - 2.6.26-1-686

  Read the article

• Wammu - USB Device Name?

  - by Paul

  I'm trying to get to my phone's filesystem through USB in Wammu, but I'm stuck in the configuration wizard when it asks for a USB device name. After about an hour of Internet searching, here are the failed solutions I've already tried, starting with the relevant information returned by lsusb in terminal. lsusb Bus 001 Device 003: ID 12d1:101e Huawei Technologies Co., Ltd. So I tried opening Wammu through sudo wammu in terminal and inputting "/dev/bus/usb/001/003" as the device name, which returns: Error opening device Device /dev/bus/usb/001/003 does not exist! and then "/dev/bus/usb/001/", which returns: Failed to connect to phone Description: Error opening device. Unknown, busy, or no permissions.<br> Function: Init<br> Error code: 2 Another proposed solution was to try "tail -f /var/log/messages" in terminal. But that only returned a "No such file or directory" message. Seemingly relevant dmesg info: [ 4739.716214] usb 1-1: new high-speed USB device number 8 using ehci_hcd [ 4739.854137] scsi9 : usb-storage 1-1:1.0 [ 4740.854416] scsi 9:0:0:0: CD-ROM HUAWEI T Mass Storage 2.31 PQ: 0 ANSI: 2 [ 4740.867051] sr0: scsi-1 drive [ 4740.867806] sr 9:0:0:0: Attached scsi CD-ROM sr0 [ 4740.870464] sr 9:0:0:0: Attached scsi generic sg1 type 5 I don't know why it is coming up as CD-ROM. But there it is. If you haven't noticed already, I'm an absolute beginner when it comes to Linux and terminal. So speaking to me like I'm a three year old is welcome if you can propose a solution. I'm running Ubuntu 12.04 LTS, and the phone is a Huawei U1250. My computer is an Acer Aspire One D250/KAV60. Any help is much appreciated.

  Read the article

• External USB hard-drive changing drive letter

  - by Sydius

  I have a Seagate FreeAgent Go external USB hard drive that was mounted but mysteriously decided to reconnect itself: Sep 30 15:07:06 feinman kernel: [243901.551604] usb 1-1.2: USB disconnect, device number 3 Sep 30 15:07:06 feinman kernel: [243901.553828] sd 6:0:0:0: [sdb] Synchronizing SCSI cache Sep 30 15:07:06 feinman kernel: [243901.553893] sd 6:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK Sep 30 15:07:10 feinman kernel: [243905.336557] usb 1-1.2: new high-speed USB device number 4 using ehci_hcd Sep 30 15:07:10 feinman kernel: [243905.431219] scsi7 : usb-storage 1-1.2:1.0 Sep 30 15:07:11 feinman kernel: [243906.427207] scsi 7:0:0:0: Direct-Access Seagate FreeAgent Go 0148 PQ: 0 ANSI: 4 Sep 30 15:07:11 feinman kernel: [243906.428303] sd 7:0:0:0: Attached scsi generic sg1 type 0 Sep 30 15:07:11 feinman kernel: [243906.430317] sd 7:0:0:0: [sdc] 625142447 512-byte logical blocks: (320 GB/298 GiB) Sep 30 15:07:11 feinman kernel: [243906.430860] sd 7:0:0:0: [sdc] Write Protect is off Sep 30 15:07:11 feinman kernel: [243906.430865] sd 7:0:0:0: [sdc] Mode Sense: 1c 00 00 00 Sep 30 15:07:11 feinman kernel: [243906.431386] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Sep 30 15:07:11 feinman kernel: [243906.493674] sdc: sdc1 Sep 30 15:07:11 feinman kernel: [243906.496109] sd 7:0:0:0: [sdc] Attached SCSI disk It changed from sdb to sdc, causing a number of problems for me. What can I do to further track down the cause? I thought it might be a problem with it sleeping but when I cat /sys/class/scsi_disk/6\:0\:0\:0/allow_restart, I see that it's already 1.

  Read the article

• One of the partion on a usb harddisk cannot automount

  - by holmescn

  It is a very strange problem. My usb harddisk has four partitions, one is primary, the other three are logical (contained within an extended partition). When I plug in the disk, three of the partitions are mounted automatically except one--the first logical partition in the extended partition. Initially I thought it is the problem of system (at that time I used Mint). But after I change to Ubuntu 12.04, the problem wasn't solved. I don't want to add a rule in fstab, and I want to know what happened. The disk is fine, and the partition can be accessed in Windows and mounted manually. result of dmesg | tail: [100933.557649] usb 2-1.2: new high-speed USB device number 4 using ehci_hcd [100933.651891] scsi8 : usb-storage 2-1.2:1.0 [100934.649047] scsi 8:0:0:0: Direct-Access SAMSUNG PQ: 0 ANSI: 0 [100934.650963] sd 8:0:0:0: Attached scsi generic sg2 type 0 [100934.651342] sd 8:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [100934.651977] sd 8:0:0:0: [sdb] Write Protect is off [100934.651989] sd 8:0:0:0: [sdb] Mode Sense: 03 00 00 00 [100934.652836] sd 8:0:0:0: [sdb] No Caching mode page present [100934.652848] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.655354] sd 8:0:0:0: [sdb] No Caching mode page present [100934.655367] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.734652] sdb: sdb1 sdb3 < sdb5 sdb6 sdb7 > [100934.737706] sd 8:0:0:0: [sdb] No Caching mode page present [100934.737725] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.737731] sd 8:0:0:0: [sdb] Attached SCSI disk result of parted -l: Model: SAMSUNG (scsi) Disk /dev/sdb: 320GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 21.5GB 21.5GB primary ntfs 3 21.5GB 320GB 299GB extended lba 5 21.5GB 129GB 107GB logical ntfs 6 129GB 236GB 107GB logical ntfs 7 236GB 320GB 83.8GB logical ntfs

  Read the article

• Why is LSHW Only listing one of my two HDDs?

  - by Mark

  I have a 120GB HDD and a 1TB HDD in the system. I installed Ubuntu Server using LVM on the 120GB. After installation I added the 1TB to the existing volume group and added 10GB to /home as a test. My understanding is that lshw is supposed to list hardware. What's the difference here? mark@server:~$ sudo lshw -short -c disk H/W path Device Class Description ========================================================= /0/100/1f.2/0 /dev/sda disk 120GB ST3120026AS /0/100/1f.2/1 /dev/cdrom disk DVD+-RW GH50N /0/1/0.0.0 /dev/sdc disk SCSI Disk /0/1/0.0.1 /dev/sdd disk SCSI Disk /0/1/0.0.2 /dev/sde disk SCSI Disk /0/1/0.0.3 /dev/sdf disk SCSI Disk The 1TB only shows up as a volume, not as a disk. mark@server:~$ sudo lshw -short .... /0/100/1f.2/0 /dev/sda disk 120GB ST3120026AS /0/100/1f.2/0/1 /dev/sda1 volume 476MiB Linux filesystem partition /0/100/1f.2/0/2 /dev/sda2 volume 111GiB Linux LVM Physical Volume partition /0/100/1f.2/1 /dev/cdrom disk DVD+-RW GH50N /0/100/1f.2/0.0.0 /dev/sdb volume 931GiB WDC WD1001FALS-0 Thanks, Mark

  Read the article

• libvirt upgrade caused vms to not see drives (boot media not found)

  - by bias

  I upgraded to Ubuntu 12.04.1 and now libvirt (via open nebula) successfully runs vms but they aren't finding the 2 drives (specifically, the boot drive). One is "hd" the other is "cdrom". The machine boots but fails and displays something like "boot media not found hd" (this was in a vnc terminal and I didn't copy the output anywhere so that's not the verbatim message). I tried constructing a new disk using the new version of qemu (via vmbuilder) and this new machine has the same problem as the old machine. In case it matters (I can't see why it would) I'm using open nebula to manage the machines. There's nothing relevant in any of the logs: syslog, libvirtd, oned. Which is to say nothing interesting/anomalous is reported when the machine is brought up. Versions libvirt 0.9.8-2ubuntu17.4 qemu-kvm 1.0+noroms-0ubuntu14.3 The libvirt xml config portions (relavent) <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> ... <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='qcow2'/> <source file='/var/lib/one//203/images/disk.0'/> <target dev='sda' bus='scsi'/> <alias name='scsi0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/var/lib/one//203/images/disk.1'/> <target dev='sdc' bus='scsi'/> <readonly/> <alias name='scsi0-0-2'/> <address type='drive' controller='0' bus='0' unit='2'/> </disk> <controller type='scsi' index='0'> <alias name='scsi0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </controller> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </memballoon> ... </devices> The libvirt/qemu log contains 2012-11-25 22:19:24.328+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 256 -smp 1,sockets=1,cores=1,threads=1 -name one-204 -uuid 4be6c276-19e8-bdc2-e9c9-9ca5352f2be3 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/one-204.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -device lsi,id=scsi0,bus=pci.0,addr=0x5 -drive file=/var/lib/one//204/images/disk.0,if=none,id=drive-scsi0-0-0,format=qcow2 -device scsi-disk,bus=scsi0.0,scsi-id=0,drive=drive-scsi0-0-0,id=scsi0-0-0,bootindex=1 -drive file=/var/lib/one//204/images/disk.1,if=none,media=cdrom,id=drive-scsi0-0-2,readonly=on,format=raw -device scsi-disk,bus=scsi0.0,scsi-id=2,drive=drive-scsi0-0-2,id=scsi0-0-2 -netdev tap,fd=18,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3 -netdev tap,fd=19,id=hostnet1 -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4 -usb -vnc 0.0.0.0:204 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x6 kvm: -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom" kvm: -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom"

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• How to reduce virtual memory by optimising my PHP code?

  - by iCeR

  My current code (see below) uses 147MB of virtual memory! My provider has allocated 100MB by default and the process is killed once run, causing an internal error. The code is utilising curl multi and must be able to loop with more than 150 iterations whilst still minimizing the virtual memory. The code below is only set at 150 iterations and still causes the internal server error. At 90 iterations the issue does not occur. How can I adjust my code to lower the resource use / virtual memory? Thanks! <?php function udate($format, $utimestamp = null) { if ($utimestamp === null) $utimestamp = microtime(true); $timestamp = floor($utimestamp); $milliseconds = round(($utimestamp - $timestamp) * 1000); return date(preg_replace('`(?<!\\\\)u`', $milliseconds, $format), $timestamp); } $url = 'https://www.testdomain.com/'; $curl_arr = array(); $master = curl_multi_init(); for($i=0; $i<150; $i++) { $curl_arr[$i] = curl_init(); curl_setopt($curl_arr[$i], CURLOPT_URL, $url); curl_setopt($curl_arr[$i], CURLOPT_RETURNTRANSFER, 1); curl_setopt($curl_arr[$i], CURLOPT_SSL_VERIFYHOST, FALSE); curl_setopt($curl_arr[$i], CURLOPT_SSL_VERIFYPEER, FALSE); curl_multi_add_handle($master, $curl_arr[$i]); } do { curl_multi_exec($master,$running); } while($running > 0); for($i=0; $i<150; $i++) { $results = curl_multi_getcontent ($curl_arr[$i]); $results = explode("<br>", $results); echo $results[0]; echo "<br>"; echo $results[1]; echo "<br>"; echo udate('H:i:s:u'); echo "<br><br>"; usleep(100000); } ?> Processor Information Total processors: 8 Processor #1 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #2 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #3 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #4 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #5 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #6 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #7 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #8 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Memory Information Memory for crash kernel (0x0 to 0x0) notwithin permissible range Memory: 8302344k/9175040k available (2176k kernel code, 80272k reserved, 901k data, 228k init, 7466304k highmem) System Information Linux server3.server.com 2.6.18-194.17.1.el5PAE #1 SMP Wed Sep 29 13:31:51 EDT 2010 i686 i686 i386 GNU/Linux Physical Disks SCSI device sda: 1952448512 512-byte hdwr sectors (999654 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write back SCSI device sda: 1952448512 512-byte hdwr sectors (999654 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write back sd 0:1:0:0: Attached scsi disk sda sd 4:0:0:0: Attached scsi removable disk sdb sd 0:1:0:0: Attached scsi generic sg4 type 0 sd 4:0:0:0: Attached scsi generic sg7 type 0 Current Memory Usage total used free shared buffers cached Mem: 8306672 7847384 459288 0 487912 6444548 -/+ buffers/cache: 914924 7391748 Swap: 4095992 496 4095496 Total: 12402664 7847880 4554784 Current Disk Usage Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 898G 307G 546G 36% / /dev/sda1 99M 19M 76M 20% /boot none 4.0G 0 4.0G 0% /dev/shm /var/tmpMnt 4.0G 1.8G 2.0G 48% /tmp

  Read the article

• Cannot mount Android phone in Ubuntu and sync with Banshee

  - by Brett Alton

  I can't get my LG Optimus One to sync with Banshee. I read somewhere that the root needs to have an empty file called '.is_audio_player'. I did that and it still doesn't mount. I ran dmesg however and it appears that the card is unmounting before I even have a change to run Banshee. [ 7250.321359] usb 1-1.4: new high speed USB device using ehci_hcd and address 10 [ 7250.444795] scsi12 : usb-storage 1-1.4:1.0 [ 7251.567946] scsi 12:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 7251.568839] sd 12:0:0:0: Attached scsi generic sg3 type 0 [ 7252.232433] sd 12:0:0:0: [sdc] 15564800 512-byte logical blocks: (7.96 GB/7.42 GiB) [ 7252.233299] sd 12:0:0:0: [sdc] Write Protect is off [ 7252.233306] sd 12:0:0:0: [sdc] Mode Sense: 03 00 00 00 [ 7252.233309] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.235658] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.235666] sdc: sdc1 [ 7252.239132] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.239140] sd 12:0:0:0: [sdc] Attached SCSI removable disk [ 7272.573437] usb 1-1.4: USB disconnect, address 10 Suggestions?

  Read the article

• Lenovo B570 doesn't boot after installation

  - by Alan

  I install my Ubuntu 11.10 64 Bits in my Notebook Lenovo B570. (I remove Win 7). I have no problems to install. But at finish, when it start, it wont boot. It search for another boot device (Network, CD/DVD). Maybe it issue is about SCSI Hard Drive. I try in BIOS set compatible mode SCSI/ATA. It try locate another boot (Networks, CD/DVD). I try to enable compatible mode in BIOS SCSI - SATA and reinstall again. "Will ubuntu be the only os on your computer or is there a 2nd os?" A:Yes. I remove Windows 7 and use All disc to Ubuntu.

  Read the article

• Cannot mount Android phone and sync with Banshee

  - by Brett Alton

  I can't get my LG Optimus One to sync with Banshee. I read somewhere that the root needs to have an empty file called '.is_audio_player'. I did that and it still doesn't mount. I ran dmesg however and it appears that the card is unmounting before I even have a change to run Banshee. [ 7250.321359] usb 1-1.4: new high speed USB device using ehci_hcd and address 10 [ 7250.444795] scsi12 : usb-storage 1-1.4:1.0 [ 7251.567946] scsi 12:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 7251.568839] sd 12:0:0:0: Attached scsi generic sg3 type 0 [ 7252.232433] sd 12:0:0:0: [sdc] 15564800 512-byte logical blocks: (7.96 GB/7.42 GiB) [ 7252.233299] sd 12:0:0:0: [sdc] Write Protect is off [ 7252.233306] sd 12:0:0:0: [sdc] Mode Sense: 03 00 00 00 [ 7252.233309] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.235658] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.235666] sdc: sdc1 [ 7252.239132] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.239140] sd 12:0:0:0: [sdc] Attached SCSI removable disk [ 7272.573437] usb 1-1.4: USB disconnect, address 10 Suggestions?

  Read the article

• ?11gR2 RAC???ASM DISK Path????

  - by Liu Maclean(???)

  ????T.askmaclean.com???????11gR2?ASM DISK?????,??????: aix 6.1,grid 11.2.0.3+asm11.2.0.3+rac ???????????aix????????mpio,??diskgroup ?????veritas dmp???,?????asm?disk_strings=/dev/vx/rdmp/*,crs/asm??????????????/dev/vx/rdmp/?????,?????????diskgroup??? crs???????:2012-07-13 15:07:29.748: [ GPNP][1286]clsgpnp_profileCallUrlInt: [at clsgpnp.c:2108 clsgpnp_profileCallUrlInt] get-profile call to url “ipc://GPNPD_ggtest1? disco “” [f=0 claimed- host: cname: seq: auth:]2012-07-13 15:07:29.762: [ GPNP][1286]clsgpnp_profileCallUrlInt: [at clsgpnp.c:2236 clsgpnp_profileCallUrlInt] Result: (0) CLSGPNP_OK. Successful get-profile CALL to remote “ipc://GPNPD_ggtest1? disco “”2012-07-13 15:07:29.762: [ CSSD][1286]clssnmReadDiscoveryProfile: voting file discovery string(/dev/vx/rdmp/*)2012-07-13 15:07:29.762: [ CSSD][1286]clssnmvDDiscThread: using discovery string /dev/vx/rdmp/* for initial discovery2012-07-13 15:07:29.762: [ SKGFD][1286]Discovery with str:/dev/vx/rdmp/*: 2012-07-13 15:07:29.762: [ SKGFD][1286]UFS discovery with :/dev/vx/rdmp/*: 2012-07-13 15:07:29.769: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_919: 2012-07-13 15:07:29.770: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_212: 2012-07-13 15:07:29.770: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_211: 2012-07-13 15:07:29.770: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_210: 2012-07-13 15:07:29.770: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_209: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_181: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_180: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/disk_3: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/disk_2: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/disk_1: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/disk_0: 2012-07-13 15:07:29.771: [ SKGFD][1286]OSS discovery with :/dev/vx/rdmp/*: 2012-07-13 15:07:29.771: [ SKGFD][1286]Handle 1115e7510 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_916: 2012-07-13 15:07:29.772: [ SKGFD][1286]Handle 1118758b0 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_912: 2012-07-13 15:07:29.773: [ SKGFD][1286]Handle 1118d9cf0 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_908: 2012-07-13 15:07:29.773: [ SKGFD][1286]Handle 1118da450 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_904: 2012-07-13 15:07:29.773: [ SKGFD][1286]Handle 1118dad70 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_903: 2012-07-13 15:07:29.802: [ CLSF][1286]checksum failed for disk:/dev/vx/rdmp/v_df8000_916:2012-07-13 15:07:29.803: [ SKGFD][1286]Lib :UFS:: closing handle 1115e7510 for disk :/dev/vx/rdmp/v_df8000_916: 2012-07-13 15:07:29.803: [ SKGFD][1286]Lib :UFS:: closing handle 1118758b0 for disk :/dev/vx/rdmp/v_df8000_912: 2012-07-13 15:07:29.804: [ SKGFD][1286]Handle 1115e6710 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_202: 2012-07-13 15:07:29.808: [ SKGFD][1286]Handle 1115e7030 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_201: 2012-07-13 15:07:29.809: [ SKGFD][1286]Handle 1115e7ad0 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_200: 2012-07-13 15:07:29.809: [ SKGFD][1286]Handle 1118733f0 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_199: 2012-07-13 15:07:29.816: [ CLSF][1286]checksum failed for disk:/dev/vx/rdmp/v_df8000_186:2012-07-13 15:07:29.816: [ SKGFD][1286]Lib :UFS:: closing handle 1118de5d0 for disk :/dev/vx/rdmp/v_df8000_186: 2012-07-13 15:07:29.816: [ CSSD][1286]clssnmvDiskVerify: Successful discovery of 0 disks2012-07-13 15:07:29.816: [ CSSD][1286]clssnmCompleteInitVFDiscovery: Completing initial voting file discovery2012-07-13 15:07:29.816: [ CSSD][1286]clssnmvFindInitialConfigs: No voting files found2012-07-13 15:07:29.816: [ CSSD][1286](:CSSNM00070:)clssnmCompleteInitVFDiscovery: Voting file not found. Retrying discovery in 15 seconds2012-07-13 15:07:30.169: [ CSSD][1029]clssgmExecuteClientRequest(): type(37) size(80) only connect and exit messages are allowed before lease acquisition proc(1115e4870) client(0) ??????ASM DISK PATH???????,????11gR2 RAC+ASM????,??CRS??????,????crsctl start crs -excl -nocrs???????CSS???ASM??, ???????(clssnmCompleteInitVFDiscovery: Voting file not found),????Voteing file????????????????? ?????????,???????11gR2 RAC+ASM??ASM DISK??: 1.?????????ASM DISK?????,??????UDEV????????,???UDEV????ASM DISK?/dev/asm-disk* ??? /dev/rasm-disk*???, ??????udev rule??????: [grid@maclean1 ~]$ export ORACLE_HOME=/g01/grid/app/11.2.0/grid [grid@maclean1 ~]$ /g01/grid/app/11.2.0/grid/bin/sqlplus / as sysasm SQL*Plus: Release 11.2.0.3.0 Production on Sun Jul 15 04:09:28 2012 Copyright (c) 1982, 2011, Oracle. All rights reserved. Connected to: Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production With the Real Application Clusters and Automatic Storage Management options SQL> show parameter diskstri NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ asm_diskstring string /dev/asm* ??????ASM?????asm_diskstring ?/dev/asm*, ???root????UDEV RULE?? : [root@maclean1 rules.d]# cp 99-oracle-asmdevices.rules 99-oracle-asmdevices.rules.bak [root@maclean1 rules.d]# vi 99-oracle-asmdevices.rules [root@maclean1 rules.d]# cat 99-oracle-asmdevices.rules KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB09cadb31-cfbea255_", NAME="rasm-diskb", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB5f097069-59efb82f_", NAME="rasm-diskc", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB4e1a81c0-20478bc4_", NAME="rasm-diskd", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VBdcce9285-b13c5a27_", NAME="rasm-diske", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB82effe1a-dbca7dff_", NAME="rasm-diskf", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB950d279f-c581cb51_", NAME="rasm-diskg", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB14400d81-651672d7_", NAME="rasm-diskh", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB31b1237b-78aa22bb_", NAME="rasm-diski", OWNER="grid", GROUP="asmadmin", MODE="0660" ???????99-oracle-asmdevices.rules?UDEV RULE????,??????????/dev/rasm-disk*???,??????ASM DISK???, ????????????????RAC CRS??????? ??????votedisk?ocr ????: [root@maclean1 rules.d]# /g01/grid/app/11.2.0/grid/bin/crsctl query css votedisk ## STATE File Universal Id File Name Disk group -- ----- ----------------- --------- --------- 1. ONLINE 6896bfc3d1464f9fbf0ea9df87e023ad (/dev/asm-diskb) [SYSTEMDG] 2. ONLINE 58eb81b656084ff2bfd315d9badd08b7 (/dev/asm-diskc) [SYSTEMDG] 3. ONLINE 6bf7324625c54f3abf2c942b1e7f70d9 (/dev/asm-diskd) [SYSTEMDG] 4. ONLINE 43ad8ae20c354f5ebf7083bc30bf94cc (/dev/asm-diske) [SYSTEMDG] 5. ONLINE 4c225359d51b4f93bfba01080664b3d7 (/dev/asm-diskf) [SYSTEMDG] Located 5 voting disk(s). [root@maclean1 rules.d]# /g01/grid/app/11.2.0/grid/bin/ocrcheck Status of Oracle Cluster Registry is as follows : Version : 3 Total space (kbytes) : 262120 Used space (kbytes) : 2844 Available space (kbytes) : 259276 ID : 879001605 Device/File Name : +SYSTEMDG Device/File integrity check succeeded Device/File not configured Device/File not configured Device/File not configured Device/File not configured Cluster registry integrity check succeeded Logical corruption check succeeded ??votedisk file?????????ASM DISK,?????????crsctl replace votedisk, ??????LINUX OS: [root@maclean1 rules.d]# init 6 rebooting ............ [root@maclean1 dev]# ls -l *asm* brw-rw---- 1 grid asmadmin 8, 16 Jul 15 04:15 rasm-diskb brw-rw---- 1 grid asmadmin 8, 32 Jul 15 04:15 rasm-diskc brw-rw---- 1 grid asmadmin 8, 48 Jul 15 04:15 rasm-diskd brw-rw---- 1 grid asmadmin 8, 64 Jul 15 04:15 rasm-diske brw-rw---- 1 grid asmadmin 8, 80 Jul 15 04:15 rasm-diskf brw-rw---- 1 grid asmadmin 8, 96 Jul 15 04:15 rasm-diskg brw-rw---- 1 grid asmadmin 8, 112 Jul 15 04:15 rasm-diskh brw-rw---- 1 grid asmadmin 8, 128 Jul 15 04:15 rasm-diski ??????????/dev/rasm-disk*?ASM DISK,??ASM??????css?????/dev/asm*?????ASM DISK,??????????????ASM DISK: more /g01/grid/app/11.2.0/grid/log/maclean1/cssd/ocssd.log 2012-07-15 04:17:45.208: [ SKGFD][1099548992]Discovery with str:/dev/asm*: 2012-07-15 04:17:45.208: [ SKGFD][1099548992]UFS discovery with :/dev/asm*: 2012-07-15 04:17:45.208: [ SKGFD][1099548992]OSS discovery with :/dev/asm*: 2012-07-15 04:17:45.208: [ CSSD][1099548992]clssnmvDiskVerify: Successful discovery of 0 disks 2012-07-15 04:17:45.208: [ CSSD][1099548992]clssnmCompleteInitVFDiscovery: Completing initial voting file discovery 2012-07-15 04:17:45.208: [ CSSD][1099548992]clssnmvFindInitialConfigs: No voting files found 2012-07-15 04:17:45.208: [ CSSD][1099548992](:CSSNM00070:)clssnmCompleteInitVFDiscovery: Voting file not found. Retrying discovery in 15 seconds 2012-07-15 04:17:45.251: [ CSSD][1096661312]clssgmExecuteClientRequest(): type(37) size(80) only connect and exit messages are allowed before lease acquisition proc(0x26a8ba0) client((nil)) 2012-07-15 04:17:45.251: [ CSSD][1096661312]clssgmDeadProc: proc 0x26a8ba0 2012-07-15 04:17:45.251: [ CSSD][1096661312]clssgmDestroyProc: cleaning up proc(0x26a8ba0) con(0xfe6) skgpid ospid 3751 with 0 clients, refcount 0 2012-07-15 04:17:45.252: [ CSSD][1096661312]clssgmDiscEndpcl: gipcDestroy 0xfe6 2012-07-15 04:17:45.829: [ CSSD][1096661312]clssscSelect: cookie accept request 0x2318ea0 2012-07-15 04:17:45.829: [ CSSD][1096661312]clssgmAllocProc: (0x2659480) allocated 2012-07-15 04:17:45.830: [ CSSD][1096661312]clssgmClientConnectMsg: properties of cmProc 0x2659480 - 1,2,3,4,5 2012-07-15 04:17:45.830: [ CSSD][1096661312]clssgmClientConnectMsg: Connect from con(0x114e) proc(0x2659480) pid(3751) version 11:2:1:4, properties: 1,2,3,4,5 2012-07-15 04:17:45.830: [ CSSD][1096661312]clssgmClientConnectMsg: msg flags 0x0000 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssscSelect: cookie accept request 0x253ddd0 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssscevtypSHRCON: getting client with cmproc 0x253ddd0 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssgmRegisterClient: proc(3/0x253ddd0), client(61/0x26877b0) 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssgmExecuteClientRequest(): type(6) size(684) only connect and exit messages are  allowed before lease acquisition proc(0x253ddd0) client(0x26877b0) 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssgmDiscEndpcl: gipcDestroy 0x1174 2012-07-15 04:17:46.070: [ CSSD][1096661312]clssscSelect: cookie accept request 0x26368a0 2012-07-15 04:17:46.070: [ CSSD][1096661312]clssscevtypSHRCON: getting client with cmproc 0x26368a0 2012-07-15 04:17:46.070: [ CSSD][1096661312]clssgmRegisterClient: proc(5/0x26368a0), client(50/0x26877b0) ??11gR2?CRS?????ASM,??ocr???ASM?,??ASM???????,???CRS?????????: [root@maclean1 ~]# crsctl check has CRS-4638: Oracle High Availability Services is online [root@maclean1 ~]# crsctl check crs CRS-4638: Oracle High Availability Services is online CRS-4535: Cannot communicate with Cluster Ready Services CRS-4530: Communications failure contacting Cluster Synchronization Services daemon CRS-4534: Cannot communicate with Event Manager 2. ?????ASM DISK PATH???????,?????????????CRS: ??????OHASD??: [root@maclean1 ~]# crsctl stop has -f CRS-2791: Starting shutdown of Oracle High Availability Services-managed resources on 'maclean1' CRS-2673: Attempting to stop 'ora.mdnsd' on 'maclean1' CRS-2673: Attempting to stop 'ora.crf' on 'maclean1' CRS-2677: Stop of 'ora.mdnsd' on 'maclean1' succeeded CRS-2677: Stop of 'ora.crf' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.gipcd' on 'maclean1' CRS-2677: Stop of 'ora.gipcd' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.gpnpd' on 'maclean1' CRS-2677: Stop of 'ora.gpnpd' on 'maclean1' succeeded CRS-2793: Shutdown of Oracle High Availability Services-managed resources on 'maclean1' has completed CRS-4133: Oracle High Availability Services has been stopped. 3. ?-excl -nocrs????CRS,?????ASM ???????CRS??: [root@maclean1 ~]# crsctl start crs -excl -nocrs  CRS-4123: Oracle High Availability Services has been started. CRS-2672: Attempting to start 'ora.mdnsd' on 'maclean1' CRS-2676: Start of 'ora.mdnsd' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.gpnpd' on 'maclean1' CRS-2676: Start of 'ora.gpnpd' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.cssdmonitor' on 'maclean1' CRS-2672: Attempting to start 'ora.gipcd' on 'maclean1' CRS-2676: Start of 'ora.cssdmonitor' on 'maclean1' succeeded CRS-2676: Start of 'ora.gipcd' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.cssd' on 'maclean1' CRS-2672: Attempting to start 'ora.diskmon' on 'maclean1' CRS-2676: Start of 'ora.diskmon' on 'maclean1' succeeded CRS-2676: Start of 'ora.cssd' on 'maclean1' succeeded CRS-2679: Attempting to clean 'ora.cluster_interconnect.haip' on 'maclean1' CRS-2672: Attempting to start 'ora.ctssd' on 'maclean1' CRS-2681: Clean of 'ora.cluster_interconnect.haip' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.cluster_interconnect.haip' on 'maclean1' CRS-2676: Start of 'ora.ctssd' on 'maclean1' succeeded CRS-2676: Start of 'ora.cluster_interconnect.haip' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.asm' on 'maclean1' CRS-2676: Start of 'ora.asm' on 'maclean1' succeeded #??????CRS_HOME???ORACLE_BASE?777??,??????? [root@maclean1 ~]# chmod 777 /g01 4.??ASM???disk_strings????ASM DISK PATH??: [root@maclean1 ~]# su - grid [grid@maclean1 ~]$ sqlplus / as sysasm SQL*Plus: Release 11.2.0.3.0 Production on Sun Jul 15 04:40:40 2012 Copyright (c) 1982, 2011, Oracle. All rights reserved. Connected to: Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production With the Real Application Clusters and Automatic Storage Management options SQL> alter system set asm_diskstring='/dev/rasm*'; System altered. SQL> alter diskgroup systemdg mount; Diskgroup altered. SQL> create spfile from memory; File created. SQL> startup force mount; ORA-32004: obsolete or deprecated parameter(s) specified for ASM instance ASM instance started Total System Global Area 283930624 bytes Fixed Size 2227664 bytes Variable Size 256537136 bytes ASM Cache 25165824 bytes ASM diskgroups mounted SQL> show parameter spfile NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ spfile string /g01/grid/app/11.2.0/grid/dbs/ spfile+ASM1.ora SQL> show parameter disk NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ asm_diskgroups string SYSTEMDG asm_diskstring string /dev/rasm* SQL> create pfile from spfile; File created. SQL> create spfile='+SYSTEMDG' from pfile; File created. SQL> startup force; ORA-32004: obsolete or deprecated parameter(s) specified for ASM instance ASM instance started Total System Global Area 283930624 bytes Fixed Size 2227664 bytes Variable Size 256537136 bytes ASM Cache 25165824 bytes ASM diskgroups mounted SQL> show parameter spfile NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ spfile string +SYSTEMDG/maclean-cluster/asmp arameterfile/registry.253.7886 82933 ???????asm_diskstring ,????ASM DISKGROUP??SPFILE , ??ASM?????SPFILE?????????????????? 5. crsctl replace votedisk ???votedisk????: [root@maclean1 ~]# crsctl replace votedisk +systemdg Successful addition of voting disk 864a00efcfbe4f42bfd0f4f6b60472a0. Successful addition of voting disk ab14d6e727614f29bf53b9870052a5c8. Successful addition of voting disk 754c03c168854f46bf2daee7287bf260. Successful addition of voting disk 9ed58f37f3e84f28bfcd9b101f2af9f3. Successful addition of voting disk 4ce7b7c682364f12bf4df5ce1fb7814e. Successfully replaced voting disk group with +systemdg. CRS-4266: Voting file(s) successfully replaced [root@maclean1 ~]# crsctl query css votedisk ## STATE File Universal Id File Name Disk group -- ----- ----------------- --------- --------- 1. ONLINE 864a00efcfbe4f42bfd0f4f6b60472a0 (/dev/rasm-diskb) [SYSTEMDG] 2. ONLINE ab14d6e727614f29bf53b9870052a5c8 (/dev/rasm-diskc) [SYSTEMDG] 3. ONLINE 754c03c168854f46bf2daee7287bf260 (/dev/rasm-diskd) [SYSTEMDG] 4. ONLINE 9ed58f37f3e84f28bfcd9b101f2af9f3 (/dev/rasm-diske) [SYSTEMDG] 5. ONLINE 4ce7b7c682364f12bf4df5ce1fb7814e (/dev/rasm-diskf) [SYSTEMDG] Located 5 voting disk(s). [root@maclean1 ~]# ocrcheck Status of Oracle Cluster Registry is as follows : Version : 3 Total space (kbytes) : 262120 Used space (kbytes) : 2844 Available space (kbytes) : 259276 ID : 879001605 Device/File Name : +SYSTEMDG Device/File integrity check succeeded Device/File not configured Device/File not configured Device/File not configured Device/File not configured Cluster registry integrity check succeeded Logical corruption check succeeded ??replace?votedisk??? ASM DISK?,???votedisk?OCR??????? 6.??CRS??: [root@maclean1 ~]# crsctl stop crs CRS-2791: Starting shutdown of Oracle High Availability Services-managed resources on 'maclean1' CRS-2673: Attempting to stop 'ora.mdnsd' on 'maclean1' CRS-2673: Attempting to stop 'ora.ctssd' on 'maclean1' CRS-2673: Attempting to stop 'ora.asm' on 'maclean1' CRS-2677: Stop of 'ora.mdnsd' on 'maclean1' succeeded CRS-2677: Stop of 'ora.asm' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.cluster_interconnect.haip' on 'maclean1' CRS-2677: Stop of 'ora.ctssd' on 'maclean1' succeeded CRS-2677: Stop of 'ora.cluster_interconnect.haip' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.cssd' on 'maclean1' CRS-2677: Stop of 'ora.cssd' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.gipcd' on 'maclean1' CRS-2677: Stop of 'ora.gipcd' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.gpnpd' on 'maclean1' CRS-2677: Stop of 'ora.gpnpd' on 'maclean1' succeeded CRS-2793: Shutdown of Oracle High Availability Services-managed resources on 'maclean1' has completed CRS-4133: Oracle High Availability Services has been stopped. [root@maclean1 ~]# crsctl stat res -t -------------------------------------------------------------------------------- NAME TARGET STATE SERVER STATE_DETAILS -------------------------------------------------------------------------------- Local Resources -------------------------------------------------------------------------------- ora.BACKUPDG.dg ONLINE ONLINE maclean1 ora.DATA.dg ONLINE ONLINE maclean1 ora.LISTENER.lsnr ONLINE ONLINE maclean1 ora.SYSTEMDG.dg ONLINE ONLINE maclean1 ora.asm ONLINE ONLINE maclean1 Started ora.gsd OFFLINE OFFLINE maclean1 ora.net1.network ONLINE ONLINE maclean1 ora.ons ONLINE ONLINE maclean1 -------------------------------------------------------------------------------- Cluster Resources -------------------------------------------------------------------------------- ora.LISTENER_SCAN1.lsnr 1 ONLINE ONLINE maclean1 ora.cvu 1 ONLINE ONLINE maclean1 ora.maclean1.vip 1 ONLINE ONLINE maclean1 ora.maclean2.vip 1 ONLINE INTERMEDIATE maclean1 FAILED OVER ora.oc4j 1 ONLINE OFFLINE STARTING ora.prod.db 1 ONLINE OFFLINE Instance Shutdown,S TARTING 2 ONLINE OFFLINE ora.scan1.vip 1 ONLINE ONLINE maclean1 ???????ASM?????SPFILE,???????????????,?????CRS??????? ??11gR2 RAC+ASM?????????,????????????????ASM DISK PATH??????????

  Read the article

• ?11gR2 RAC???ASM DISK Path????

  - by Liu Maclean(???)

  ????T.askmaclean.com???????11gR2?ASM DISK?????,??????: aix 6.1,grid 11.2.0.3+asm11.2.0.3+rac ???????????aix????????mpio,??diskgroup ?????veritas dmp???,?????asm?disk_strings=/dev/vx/rdmp/*,crs/asm??????????????/dev/vx/rdmp/?????,?????????diskgroup??? crs???????:2012-07-13 15:07:29.748: [ GPNP][1286]clsgpnp_profileCallUrlInt: [at clsgpnp.c:2108 clsgpnp_profileCallUrlInt] get-profile call to url “ipc://GPNPD_ggtest1? disco “” [f=0 claimed- host: cname: seq: auth:]2012-07-13 15:07:29.762: [ GPNP][1286]clsgpnp_profileCallUrlInt: [at clsgpnp.c:2236 clsgpnp_profileCallUrlInt] Result: (0) CLSGPNP_OK. Successful get-profile CALL to remote “ipc://GPNPD_ggtest1? disco “”2012-07-13 15:07:29.762: [ CSSD][1286]clssnmReadDiscoveryProfile: voting file discovery string(/dev/vx/rdmp/*)2012-07-13 15:07:29.762: [ CSSD][1286]clssnmvDDiscThread: using discovery string /dev/vx/rdmp/* for initial discovery2012-07-13 15:07:29.762: [ SKGFD][1286]Discovery with str:/dev/vx/rdmp/*: 2012-07-13 15:07:29.762: [ SKGFD][1286]UFS discovery with :/dev/vx/rdmp/*: 2012-07-13 15:07:29.769: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_919: 2012-07-13 15:07:29.770: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_212: 2012-07-13 15:07:29.770: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_211: 2012-07-13 15:07:29.770: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_210: 2012-07-13 15:07:29.770: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_209: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_181: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/v_df8000_180: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/disk_3: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/disk_2: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/disk_1: 2012-07-13 15:07:29.771: [ SKGFD][1286]Fetching UFS disk :/dev/vx/rdmp/disk_0: 2012-07-13 15:07:29.771: [ SKGFD][1286]OSS discovery with :/dev/vx/rdmp/*: 2012-07-13 15:07:29.771: [ SKGFD][1286]Handle 1115e7510 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_916: 2012-07-13 15:07:29.772: [ SKGFD][1286]Handle 1118758b0 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_912: 2012-07-13 15:07:29.773: [ SKGFD][1286]Handle 1118d9cf0 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_908: 2012-07-13 15:07:29.773: [ SKGFD][1286]Handle 1118da450 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_904: 2012-07-13 15:07:29.773: [ SKGFD][1286]Handle 1118dad70 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_903: 2012-07-13 15:07:29.802: [ CLSF][1286]checksum failed for disk:/dev/vx/rdmp/v_df8000_916:2012-07-13 15:07:29.803: [ SKGFD][1286]Lib :UFS:: closing handle 1115e7510 for disk :/dev/vx/rdmp/v_df8000_916: 2012-07-13 15:07:29.803: [ SKGFD][1286]Lib :UFS:: closing handle 1118758b0 for disk :/dev/vx/rdmp/v_df8000_912: 2012-07-13 15:07:29.804: [ SKGFD][1286]Handle 1115e6710 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_202: 2012-07-13 15:07:29.808: [ SKGFD][1286]Handle 1115e7030 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_201: 2012-07-13 15:07:29.809: [ SKGFD][1286]Handle 1115e7ad0 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_200: 2012-07-13 15:07:29.809: [ SKGFD][1286]Handle 1118733f0 from lib :UFS:: for disk :/dev/vx/rdmp/v_df8000_199: 2012-07-13 15:07:29.816: [ CLSF][1286]checksum failed for disk:/dev/vx/rdmp/v_df8000_186:2012-07-13 15:07:29.816: [ SKGFD][1286]Lib :UFS:: closing handle 1118de5d0 for disk :/dev/vx/rdmp/v_df8000_186: 2012-07-13 15:07:29.816: [ CSSD][1286]clssnmvDiskVerify: Successful discovery of 0 disks2012-07-13 15:07:29.816: [ CSSD][1286]clssnmCompleteInitVFDiscovery: Completing initial voting file discovery2012-07-13 15:07:29.816: [ CSSD][1286]clssnmvFindInitialConfigs: No voting files found2012-07-13 15:07:29.816: [ CSSD][1286](:CSSNM00070:)clssnmCompleteInitVFDiscovery: Voting file not found. Retrying discovery in 15 seconds2012-07-13 15:07:30.169: [ CSSD][1029]clssgmExecuteClientRequest(): type(37) size(80) only connect and exit messages are allowed before lease acquisition proc(1115e4870) client(0) ??????ASM DISK PATH???????,????11gR2 RAC+ASM????,??CRS??????,????crsctl start crs -excl -nocrs???????CSS???ASM??, ???????(clssnmCompleteInitVFDiscovery: Voting file not found),????Voteing file????????????????? ?????????,???????11gR2 RAC+ASM??ASM DISK??: 1.?????????ASM DISK?????,??????UDEV????????,???UDEV????ASM DISK?/dev/asm-disk* ??? /dev/rasm-disk*???, ??????udev rule??????: [grid@maclean1 ~]$ export ORACLE_HOME=/g01/grid/app/11.2.0/grid [grid@maclean1 ~]$ /g01/grid/app/11.2.0/grid/bin/sqlplus / as sysasm SQL*Plus: Release 11.2.0.3.0 Production on Sun Jul 15 04:09:28 2012 Copyright (c) 1982, 2011, Oracle. All rights reserved. Connected to: Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production With the Real Application Clusters and Automatic Storage Management options SQL> show parameter diskstri NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ asm_diskstring string /dev/asm* ??????ASM?????asm_diskstring ?/dev/asm*, ???root????UDEV RULE?? : [root@maclean1 rules.d]# cp 99-oracle-asmdevices.rules 99-oracle-asmdevices.rules.bak [root@maclean1 rules.d]# vi 99-oracle-asmdevices.rules [root@maclean1 rules.d]# cat 99-oracle-asmdevices.rules KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB09cadb31-cfbea255_", NAME="rasm-diskb", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB5f097069-59efb82f_", NAME="rasm-diskc", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB4e1a81c0-20478bc4_", NAME="rasm-diskd", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VBdcce9285-b13c5a27_", NAME="rasm-diske", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB82effe1a-dbca7dff_", NAME="rasm-diskf", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB950d279f-c581cb51_", NAME="rasm-diskg", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB14400d81-651672d7_", NAME="rasm-diskh", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id -g -u -s %p", RESULT=="SATA_VBOX_HARDDISK_VB31b1237b-78aa22bb_", NAME="rasm-diski", OWNER="grid", GROUP="asmadmin", MODE="0660" ???????99-oracle-asmdevices.rules?UDEV RULE????,??????????/dev/rasm-disk*???,??????ASM DISK???, ????????????????RAC CRS??????? ??????votedisk?ocr ????: [root@maclean1 rules.d]# /g01/grid/app/11.2.0/grid/bin/crsctl query css votedisk ## STATE File Universal Id File Name Disk group -- ----- ----------------- --------- --------- 1. ONLINE 6896bfc3d1464f9fbf0ea9df87e023ad (/dev/asm-diskb) [SYSTEMDG] 2. ONLINE 58eb81b656084ff2bfd315d9badd08b7 (/dev/asm-diskc) [SYSTEMDG] 3. ONLINE 6bf7324625c54f3abf2c942b1e7f70d9 (/dev/asm-diskd) [SYSTEMDG] 4. ONLINE 43ad8ae20c354f5ebf7083bc30bf94cc (/dev/asm-diske) [SYSTEMDG] 5. ONLINE 4c225359d51b4f93bfba01080664b3d7 (/dev/asm-diskf) [SYSTEMDG] Located 5 voting disk(s). [root@maclean1 rules.d]# /g01/grid/app/11.2.0/grid/bin/ocrcheck Status of Oracle Cluster Registry is as follows : Version : 3 Total space (kbytes) : 262120 Used space (kbytes) : 2844 Available space (kbytes) : 259276 ID : 879001605 Device/File Name : +SYSTEMDG Device/File integrity check succeeded Device/File not configured Device/File not configured Device/File not configured Device/File not configured Cluster registry integrity check succeeded Logical corruption check succeeded ??votedisk file?????????ASM DISK,?????????crsctl replace votedisk, ??????LINUX OS: [root@maclean1 rules.d]# init 6 rebooting ............ [root@maclean1 dev]# ls -l *asm* brw-rw---- 1 grid asmadmin 8, 16 Jul 15 04:15 rasm-diskb brw-rw---- 1 grid asmadmin 8, 32 Jul 15 04:15 rasm-diskc brw-rw---- 1 grid asmadmin 8, 48 Jul 15 04:15 rasm-diskd brw-rw---- 1 grid asmadmin 8, 64 Jul 15 04:15 rasm-diske brw-rw---- 1 grid asmadmin 8, 80 Jul 15 04:15 rasm-diskf brw-rw---- 1 grid asmadmin 8, 96 Jul 15 04:15 rasm-diskg brw-rw---- 1 grid asmadmin 8, 112 Jul 15 04:15 rasm-diskh brw-rw---- 1 grid asmadmin 8, 128 Jul 15 04:15 rasm-diski ??????????/dev/rasm-disk*?ASM DISK,??ASM??????css?????/dev/asm*?????ASM DISK,??????????????ASM DISK: more /g01/grid/app/11.2.0/grid/log/maclean1/cssd/ocssd.log 2012-07-15 04:17:45.208: [ SKGFD][1099548992]Discovery with str:/dev/asm*: 2012-07-15 04:17:45.208: [ SKGFD][1099548992]UFS discovery with :/dev/asm*: 2012-07-15 04:17:45.208: [ SKGFD][1099548992]OSS discovery with :/dev/asm*: 2012-07-15 04:17:45.208: [ CSSD][1099548992]clssnmvDiskVerify: Successful discovery of 0 disks 2012-07-15 04:17:45.208: [ CSSD][1099548992]clssnmCompleteInitVFDiscovery: Completing initial voting file discovery 2012-07-15 04:17:45.208: [ CSSD][1099548992]clssnmvFindInitialConfigs: No voting files found 2012-07-15 04:17:45.208: [ CSSD][1099548992](:CSSNM00070:)clssnmCompleteInitVFDiscovery: Voting file not found. Retrying discovery in 15 seconds 2012-07-15 04:17:45.251: [ CSSD][1096661312]clssgmExecuteClientRequest(): type(37) size(80) only connect and exit messages are allowed before lease acquisition proc(0x26a8ba0) client((nil)) 2012-07-15 04:17:45.251: [ CSSD][1096661312]clssgmDeadProc: proc 0x26a8ba0 2012-07-15 04:17:45.251: [ CSSD][1096661312]clssgmDestroyProc: cleaning up proc(0x26a8ba0) con(0xfe6) skgpid ospid 3751 with 0 clients, refcount 0 2012-07-15 04:17:45.252: [ CSSD][1096661312]clssgmDiscEndpcl: gipcDestroy 0xfe6 2012-07-15 04:17:45.829: [ CSSD][1096661312]clssscSelect: cookie accept request 0x2318ea0 2012-07-15 04:17:45.829: [ CSSD][1096661312]clssgmAllocProc: (0x2659480) allocated 2012-07-15 04:17:45.830: [ CSSD][1096661312]clssgmClientConnectMsg: properties of cmProc 0x2659480 - 1,2,3,4,5 2012-07-15 04:17:45.830: [ CSSD][1096661312]clssgmClientConnectMsg: Connect from con(0x114e) proc(0x2659480) pid(3751) version 11:2:1:4, properties: 1,2,3,4,5 2012-07-15 04:17:45.830: [ CSSD][1096661312]clssgmClientConnectMsg: msg flags 0x0000 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssscSelect: cookie accept request 0x253ddd0 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssscevtypSHRCON: getting client with cmproc 0x253ddd0 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssgmRegisterClient: proc(3/0x253ddd0), client(61/0x26877b0) 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssgmExecuteClientRequest(): type(6) size(684) only connect and exit messages are  allowed before lease acquisition proc(0x253ddd0) client(0x26877b0) 2012-07-15 04:17:45.939: [ CSSD][1096661312]clssgmDiscEndpcl: gipcDestroy 0x1174 2012-07-15 04:17:46.070: [ CSSD][1096661312]clssscSelect: cookie accept request 0x26368a0 2012-07-15 04:17:46.070: [ CSSD][1096661312]clssscevtypSHRCON: getting client with cmproc 0x26368a0 2012-07-15 04:17:46.070: [ CSSD][1096661312]clssgmRegisterClient: proc(5/0x26368a0), client(50/0x26877b0) ??11gR2?CRS?????ASM,??ocr???ASM?,??ASM???????,???CRS?????????: [root@maclean1 ~]# crsctl check has CRS-4638: Oracle High Availability Services is online [root@maclean1 ~]# crsctl check crs CRS-4638: Oracle High Availability Services is online CRS-4535: Cannot communicate with Cluster Ready Services CRS-4530: Communications failure contacting Cluster Synchronization Services daemon CRS-4534: Cannot communicate with Event Manager 2. ?????ASM DISK PATH???????,?????????????CRS: ??????OHASD??: [root@maclean1 ~]# crsctl stop has -f CRS-2791: Starting shutdown of Oracle High Availability Services-managed resources on 'maclean1' CRS-2673: Attempting to stop 'ora.mdnsd' on 'maclean1' CRS-2673: Attempting to stop 'ora.crf' on 'maclean1' CRS-2677: Stop of 'ora.mdnsd' on 'maclean1' succeeded CRS-2677: Stop of 'ora.crf' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.gipcd' on 'maclean1' CRS-2677: Stop of 'ora.gipcd' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.gpnpd' on 'maclean1' CRS-2677: Stop of 'ora.gpnpd' on 'maclean1' succeeded CRS-2793: Shutdown of Oracle High Availability Services-managed resources on 'maclean1' has completed CRS-4133: Oracle High Availability Services has been stopped. 3. ?-excl -nocrs????CRS,?????ASM ???????CRS??: [root@maclean1 ~]# crsctl start crs -excl -nocrs  CRS-4123: Oracle High Availability Services has been started. CRS-2672: Attempting to start 'ora.mdnsd' on 'maclean1' CRS-2676: Start of 'ora.mdnsd' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.gpnpd' on 'maclean1' CRS-2676: Start of 'ora.gpnpd' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.cssdmonitor' on 'maclean1' CRS-2672: Attempting to start 'ora.gipcd' on 'maclean1' CRS-2676: Start of 'ora.cssdmonitor' on 'maclean1' succeeded CRS-2676: Start of 'ora.gipcd' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.cssd' on 'maclean1' CRS-2672: Attempting to start 'ora.diskmon' on 'maclean1' CRS-2676: Start of 'ora.diskmon' on 'maclean1' succeeded CRS-2676: Start of 'ora.cssd' on 'maclean1' succeeded CRS-2679: Attempting to clean 'ora.cluster_interconnect.haip' on 'maclean1' CRS-2672: Attempting to start 'ora.ctssd' on 'maclean1' CRS-2681: Clean of 'ora.cluster_interconnect.haip' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.cluster_interconnect.haip' on 'maclean1' CRS-2676: Start of 'ora.ctssd' on 'maclean1' succeeded CRS-2676: Start of 'ora.cluster_interconnect.haip' on 'maclean1' succeeded CRS-2672: Attempting to start 'ora.asm' on 'maclean1' CRS-2676: Start of 'ora.asm' on 'maclean1' succeeded #??????CRS_HOME???ORACLE_BASE?777??,??????? [root@maclean1 ~]# chmod 777 /g01 4.??ASM???disk_strings????ASM DISK PATH??: [root@maclean1 ~]# su - grid [grid@maclean1 ~]$ sqlplus / as sysasm SQL*Plus: Release 11.2.0.3.0 Production on Sun Jul 15 04:40:40 2012 Copyright (c) 1982, 2011, Oracle. All rights reserved. Connected to: Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production With the Real Application Clusters and Automatic Storage Management options SQL> alter system set asm_diskstring='/dev/rasm*'; System altered. SQL> alter diskgroup systemdg mount; Diskgroup altered. SQL> create spfile from memory; File created. SQL> startup force mount; ORA-32004: obsolete or deprecated parameter(s) specified for ASM instance ASM instance started Total System Global Area 283930624 bytes Fixed Size 2227664 bytes Variable Size 256537136 bytes ASM Cache 25165824 bytes ASM diskgroups mounted SQL> show parameter spfile NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ spfile string /g01/grid/app/11.2.0/grid/dbs/ spfile+ASM1.ora SQL> show parameter disk NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ asm_diskgroups string SYSTEMDG asm_diskstring string /dev/rasm* SQL> create pfile from spfile; File created. SQL> create spfile='+SYSTEMDG' from pfile; File created. SQL> startup force; ORA-32004: obsolete or deprecated parameter(s) specified for ASM instance ASM instance started Total System Global Area 283930624 bytes Fixed Size 2227664 bytes Variable Size 256537136 bytes ASM Cache 25165824 bytes ASM diskgroups mounted SQL> show parameter spfile NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ spfile string +SYSTEMDG/maclean-cluster/asmp arameterfile/registry.253.7886 82933 ???????asm_diskstring ,????ASM DISKGROUP??SPFILE , ??ASM?????SPFILE?????????????????? 5. crsctl replace votedisk ???votedisk????: [root@maclean1 ~]# crsctl replace votedisk +systemdg Successful addition of voting disk 864a00efcfbe4f42bfd0f4f6b60472a0. Successful addition of voting disk ab14d6e727614f29bf53b9870052a5c8. Successful addition of voting disk 754c03c168854f46bf2daee7287bf260. Successful addition of voting disk 9ed58f37f3e84f28bfcd9b101f2af9f3. Successful addition of voting disk 4ce7b7c682364f12bf4df5ce1fb7814e. Successfully replaced voting disk group with +systemdg. CRS-4266: Voting file(s) successfully replaced [root@maclean1 ~]# crsctl query css votedisk ## STATE File Universal Id File Name Disk group -- ----- ----------------- --------- --------- 1. ONLINE 864a00efcfbe4f42bfd0f4f6b60472a0 (/dev/rasm-diskb) [SYSTEMDG] 2. ONLINE ab14d6e727614f29bf53b9870052a5c8 (/dev/rasm-diskc) [SYSTEMDG] 3. ONLINE 754c03c168854f46bf2daee7287bf260 (/dev/rasm-diskd) [SYSTEMDG] 4. ONLINE 9ed58f37f3e84f28bfcd9b101f2af9f3 (/dev/rasm-diske) [SYSTEMDG] 5. ONLINE 4ce7b7c682364f12bf4df5ce1fb7814e (/dev/rasm-diskf) [SYSTEMDG] Located 5 voting disk(s). [root@maclean1 ~]# ocrcheck Status of Oracle Cluster Registry is as follows : Version : 3 Total space (kbytes) : 262120 Used space (kbytes) : 2844 Available space (kbytes) : 259276 ID : 879001605 Device/File Name : +SYSTEMDG Device/File integrity check succeeded Device/File not configured Device/File not configured Device/File not configured Device/File not configured Cluster registry integrity check succeeded Logical corruption check succeeded ??replace?votedisk??? ASM DISK?,???votedisk?OCR??????? 6.??CRS??: [root@maclean1 ~]# crsctl stop crs CRS-2791: Starting shutdown of Oracle High Availability Services-managed resources on 'maclean1' CRS-2673: Attempting to stop 'ora.mdnsd' on 'maclean1' CRS-2673: Attempting to stop 'ora.ctssd' on 'maclean1' CRS-2673: Attempting to stop 'ora.asm' on 'maclean1' CRS-2677: Stop of 'ora.mdnsd' on 'maclean1' succeeded CRS-2677: Stop of 'ora.asm' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.cluster_interconnect.haip' on 'maclean1' CRS-2677: Stop of 'ora.ctssd' on 'maclean1' succeeded CRS-2677: Stop of 'ora.cluster_interconnect.haip' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.cssd' on 'maclean1' CRS-2677: Stop of 'ora.cssd' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.gipcd' on 'maclean1' CRS-2677: Stop of 'ora.gipcd' on 'maclean1' succeeded CRS-2673: Attempting to stop 'ora.gpnpd' on 'maclean1' CRS-2677: Stop of 'ora.gpnpd' on 'maclean1' succeeded CRS-2793: Shutdown of Oracle High Availability Services-managed resources on 'maclean1' has completed CRS-4133: Oracle High Availability Services has been stopped. [root@maclean1 ~]# crsctl stat res -t -------------------------------------------------------------------------------- NAME TARGET STATE SERVER STATE_DETAILS -------------------------------------------------------------------------------- Local Resources -------------------------------------------------------------------------------- ora.BACKUPDG.dg ONLINE ONLINE maclean1 ora.DATA.dg ONLINE ONLINE maclean1 ora.LISTENER.lsnr ONLINE ONLINE maclean1 ora.SYSTEMDG.dg ONLINE ONLINE maclean1 ora.asm ONLINE ONLINE maclean1 Started ora.gsd OFFLINE OFFLINE maclean1 ora.net1.network ONLINE ONLINE maclean1 ora.ons ONLINE ONLINE maclean1 -------------------------------------------------------------------------------- Cluster Resources -------------------------------------------------------------------------------- ora.LISTENER_SCAN1.lsnr 1 ONLINE ONLINE maclean1 ora.cvu 1 ONLINE ONLINE maclean1 ora.maclean1.vip 1 ONLINE ONLINE maclean1 ora.maclean2.vip 1 ONLINE INTERMEDIATE maclean1 FAILED OVER ora.oc4j 1 ONLINE OFFLINE STARTING ora.prod.db 1 ONLINE OFFLINE Instance Shutdown,S TARTING 2 ONLINE OFFLINE ora.scan1.vip 1 ONLINE ONLINE maclean1 ???????ASM?????SPFILE,???????????????,?????CRS??????? ??11gR2 RAC+ASM?????????,????????????????ASM DISK PATH?????????, ???????????????,????!

  Read the article

• XFS disk becomes unavailable after a while

  - by Guard

  Ubuntu 12.04 (but the same was on 11.10 before upgrading) WD MyBook, 2TB, no RAID (or RAID0, not completely sure, anyway no mirroring, both 1TB disks are in use, mounted as a single device). Formatted to XFS, normally used for big movie files. Connected to Firewire 800. At some point the LED started going up and down as when constantly reading/writing. The device gives access error. When unplugged (cable, then holding the power button for a while, then unplugging the power) and re-connected becomes available. xfs_check with no results. xfs_repair did something, but looks like didn't fix any error. Then after a massive read (checking 1.5GB torrent file for integrity) becomes unavailable again. Any ideas what's wrong? Drives? Cables? Motherboard? OS? UPD: not sure how relevant this is, but here are dmesg output [14380.632816] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [14380.633356] SGI XFS Quota Management subsystem [14421.812220] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.890596] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.896858] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14453.895347] firewire_core: created device fw1: GUID 0090a99500a35518, S400, 9 config ROM retries [14453.904818] scsi6 : SBP-2 IEEE-1394 [14453.905014] scsi7 : SBP-2 IEEE-1394 [14454.139993] firewire_sbp2: fw1.0: logged in to LUN 0000 (0 retries) [14454.158769] scsi 6:0:0:0: Direct-Access WD My Book 1015 PQ: 0 ANSI: 4 [14454.159251] sd 6:0:0:0: Attached scsi generic sg3 type 0 [14454.162391] firewire_sbp2: fw1.1: logged in to LUN 0001 (0 retries) [14454.167453] sd 6:0:0:0: [sdc] 3907017568 512-byte logical blocks: (2.00 TB/1.81 TiB) [14454.178822] sd 6:0:0:0: [sdc] Write Protect is off [14454.178826] sd 6:0:0:0: [sdc] Mode Sense: 10 00 00 00 [14454.186830] scsi 7:0:0:1: Enclosure WD My Book Device 1015 PQ: 0 ANSI: 4 [14454.186995] scsi 7:0:0:1: Attached scsi generic sg4 type 13 [14454.190078] sd 6:0:0:0: [sdc] Cache data unavailable [14454.190087] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.202176] sd 6:0:0:0: [sdc] Cache data unavailable [14454.202185] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.239940] sdc: [mac] sdc1 sdc2 sdc3 sdc4 [14454.271262] sd 6:0:0:0: [sdc] Cache data unavailable [14454.271270] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.271354] sd 6:0:0:0: [sdc] Attached SCSI disk [14454.272149] ses 7:0:0:1: Attached Enclosure device [14606.090024] XFS (sdc3): Mounting Filesystem [14612.048343] XFS (sdc3): Starting recovery (logdev: internal) [14620.697636] XFS (sdc3): Ending recovery (logdev: internal) [14748.120957] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [14748.120963] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO [14752.568382] uhci_hcd 0000:00:1a.0: PCI INT A disabled [14752.568579] uhci_hcd 0000:00:1a.1: PCI INT B disabled [14752.568738] ehci_hcd 0000:00:1a.7: PCI INT C disabled [14752.568779] ehci_hcd 0000:00:1a.7: PME# enabled [14752.584526] uhci_hcd 0000:00:1d.1: PCI INT B disabled [14752.584689] uhci_hcd 0000:00:1d.2: PCI INT C disabled [14752.680079] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xe4641000-0xe46413ff] (PCI address [0xe4641000-0xe46413ff]) [14752.680104] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b) [14752.680136] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002) [14752.680170] ehci_hcd 0000:00:1a.7: PME# disabled [14752.680182] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.680190] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [14752.710334] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [14752.710342] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [14752.749186] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [14752.749194] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [14752.790231] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 [14752.790239] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [14752.829170] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.829178] uhci_hcd 0000:00:1d.2: setting latency timer to 64

  Read the article

• Informaton of pendriver with libudv on linux

  - by Catanzaro

  I'm doing a little app in C that read the driver information of my pendrive: Plugged it and typed dmesg: [ 7676.243994] scsi 7:0:0:0: Direct-Access Lexar USB Flash Drive 1100 PQ: 0 ANSI: 0 CCS [ 7676.248359] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 7676.256733] sd 7:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB) [ 7676.266559] sd 7:0:0:0: [sdb] Write Protect is off [ 7676.266566] sd 7:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 7676.266569] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 7676.285373] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 7676.285383] sdb: sdb1 [ 7676.298661] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 7676.298667] sd 7:0:0:0: [sdb] Attached SCSI removable disk with "udevadm info -q all -n /dev/sdb" P: /devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1/1-1:1.0/host7/target7:0:0/7:0:0:0/block/sdb N: sdb W: 36 S: block/8:16 S: disk/by-id/usb-Lexar_USB_Flash_Drive_AA5OCYQII8PSQXBB-0:0 S: disk/by-path/pci-0000:02:03.0-usb-0:1:1.0-scsi-0:0:0:0 E: UDEV_LOG=3 E: DEVPATH=/devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1/1-1:1.0/host7/target7:0:0/7:0:0:0/block/sdb E: MAJOR=8 E: MINOR=16 E: DEVNAME=/dev/sdb E: DEVTYPE=disk E: SUBSYSTEM=block E: ID_VENDOR=Lexar E: ID_VENDOR_ENC=Lexar\x20\x20\x20 E: ID_VENDOR_ID=05dc E: ID_MODEL=USB_Flash_Drive E: ID_MODEL_ENC=USB\x20Flash\x20Drive\x20 E: ID_MODEL_ID=a813 E: ID_REVISION=1100 E: ID_SERIAL=Lexar_USB_Flash_Drive_AA5OCYQII8PSQXBB-0:0 E: ID_SERIAL_SHORT=AA5OCYQII8PSQXBB E: ID_TYPE=disk E: ID_INSTANCE=0:0 E: ID_BUS=usb E: ID_USB_INTERFACES=:080650: E: ID_USB_INTERFACE_NUM=00 E: ID_USB_DRIVER=usb-storage E: ID_PATH=pci-0000:02:03.0-usb-0:1:1.0-scsi-0:0:0:0 E: ID_PART_TABLE_TYPE=dos E: UDISKS_PRESENTATION_NOPOLICY=0 E: UDISKS_PARTITION_TABLE=1 E: UDISKS_PARTITION_TABLE_SCHEME=mbr E: UDISKS_PARTITION_TABLE_COUNT=1 E: DEVLINKS=/dev/block/8:16 /dev/disk/by-id/usb-Lexar_USB_Flash_Drive_AA5OCYQII8PSQXBB-0:0 /dev/disk/by-path/pci-0000:02:03.0-usb-0:1:1.0-scsi-0:0:0:0 and my software is: Codice: Seleziona tutto #include <stdio.h> #include <libudev.h> #include <stdlib.h> #include <locale.h> #include <unistd.h> int main(void) { struct udev_enumerate *enumerate; struct udev_list_entry *devices, *dev_list_entry; struct udev_device *dev; /* Create the udev object */ struct udev *udev = udev_new(); if (!udev) { printf("Can't create udev\n"); exit(0); } enumerate = udev_enumerate_new(udev); udev_enumerate_add_match_subsystem(enumerate, "scsi_generic"); udev_enumerate_scan_devices(enumerate); devices = udev_enumerate_get_list_entry(enumerate); udev_list_entry_foreach(dev_list_entry, devices) { const char *path; /* Get the filename of the /sys entry for the device and create a udev_device object (dev) representing it */ path = udev_list_entry_get_name(dev_list_entry); dev = udev_device_new_from_syspath(udev, path); /* usb_device_get_devnode() returns the path to the device node itself in /dev. */ printf("Device Node Path: %s\n", udev_device_get_devnode(dev)); /* The device pointed to by dev contains information about the hidraw device. In order to get information about the USB device, get the parent device with the subsystem/devtype pair of "usb"/"usb_device". This will be several levels up the tree, but the function will find it.*/ dev = udev_device_get_parent_with_subsystem_devtype( dev, "block", "disk"); if (!dev) { printf("Errore\n"); exit(1); } /* From here, we can call get_sysattr_value() for each file in the device's /sys entry. The strings passed into these functions (idProduct, idVendor, serial, etc.) correspond directly to the files in the directory which represents the USB device. Note that USB strings are Unicode, UCS2 encoded, but the strings returned from udev_device_get_sysattr_value() are UTF-8 encoded. */ printf(" VID/PID: %s %s\n", udev_device_get_sysattr_value(dev,"idVendor"), udev_device_get_sysattr_value(dev, "idProduct")); printf(" %s\n %s\n", udev_device_get_sysattr_value(dev,"manufacturer"), udev_device_get_sysattr_value(dev,"product")); printf(" serial: %s\n", udev_device_get_sysattr_value(dev, "serial")); udev_device_unref(dev); } /* Free the enumerator object */ udev_enumerate_unref(enumerate); udev_unref(udev); return 0; } the problem is that i obtain in output: Device Node Path: /dev/sg0 Errore and dont view information. subsystem and the devtype i think that are inserted well : "block" and "disk". thanks for help. Bye

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >