Search Results

Search found 16940 results on 678 pages for 'disk drive'.

Page 50/678 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

• Ubuntu doesn't "see" external USB Hard Disk

  - by Mina Michael

  It's NTFS. It's USB2. I'm using Ubuntu 13.04. It works perfectly fine on Windows (which excludes cable and hardware problems). I have two Ubuntu computers and it's not detected on either. It's about 500 GB. Edits: Following the first link, I input sudo lsusb in a terminal; before and after connecting the HDD. The difference was Bus 001 Device 012: ID 14cd:6116 Super Top M6116 SATA Bridge. There it is! ("sata bridge" used to appear in a windows notification when I plugged in the HDD in!). ...This means that Ubuntu detects it but is it not mounting it? I tried this: sudo mount /dev/sdb1 /mnt But gives this: mount: special device /dev/sdb1 does not exist I also tried: sudo mount /dev/sdc1 /mnt but it stays with no output forever. I left it in background for about 30 min.s. sudo fdisk -l gives out this: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xa42d04a3 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility /dev/sda2 * 80325 102481919 51200797+ 7 HPFS/NTFS/exFAT /dev/sda3 263874558 312580095 24352769 5 Extended /dev/sda4 102481920 263872511 80695296 7 HPFS/NTFS/exFAT /dev/sda5 263874560 310505471 23315456 83 Linux /dev/sda6 310507520 312580095 1036288 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x5822aaea Device Boot Start End Blocks Id System /dev/sdc1 2048 976769023 488383488 7 HPFS/NTFS/exFAT The part below "Partition table entries are not in disk order" takes about 5 minutes to appear. The outputs of ls /dev/ | grep sd before and after connecting the HDD: before: sda sda1 sda2 sda3 sda4 sda5 sda6 ,after: sda sda1 sda2 sda3 sda4 sda5 sda6 sdd sdd1 The second output has the lines sdd and sdd1 different from the first one. IT SHOWED THE FILES!! The command sudo mount /dev/sdd1 /mnt worked after I typed in sudo fdisk -l!!! Thanks a million!! :) :)

  Read the article

• Problem in booting Windows Vista after repairing using a boot repair disk

  - by Pubudu

  Been using Vista and I recently installed Ubuntu 11 in a separate hard disk(in BIOS, this hard disk was set for the 'Boot from' option)..Apart from the partitions used for Ubuntu, there are 2 more partitions(NTFS) in that hard disk..Then I installed Windows 7 on one of those partitions (just to see which Windows operating system I'd like to keep on using, along with Ubuntu)..But after installing Windows 7, the OS selection menu didn't appear anymore and had to fix it using the Boot-Repair-Disk... It kinda worked.. Now the OS selection menu is displayed.. But whenever I select Vista, it boots Windows 7...any thoughts on how to fix this? here's the link to the log generated by boot repair http://paste.debian.net/202691 I'm new to Ubuntu btw..

  Read the article

• Linux: How to find out whether the harddrive is causing a bottleneck?

  - by GetFree

  I'm not asking how to find out where a bottleneck is. I just what to know how to check if the harddrive is being used at its limit (and hence causing a bottleneck). Something like top where I can see a usage percentage of CPU and RAM. Is there something like that with which I can monitor harddrive activity? Native linux tools preferred.

  Read the article

• Is it possible to FORMAT an external hard disk that has been encrypted using Storagecrypt?

  - by Pandian John

  Basically the big problem is that about 680 GB of data from my Seagate 2 TB Ext HD is lost because I was experimenting with a software called storagecrypt. I used it a few months ago and today I tried it again but i didn't know that the old password is already set in the hard disk when I pressed the encrypt button. I forgot the password which is disappointing. Not to mention that software uses 128 bit AES encryption so there is no way iam going to recover that data. My question is that is it possible to Format my Hard disk which has been encrypted? What i mean is that is it possible to completely wipe the data just like it is newly bought so that I can use my External Hard disk?( I tried to format by right click-- Format. But the size of the disk is shown as 1 MB. Answers would be very much appreciated. Thanks.

  Read the article

• Dead-simple USB-based Windows partition cloner?

  - by OverTheRainbow

  Clonezilla is a fine open-source tool, but it requires going through several screens. Since I need to save/restore the same Windows partition, I was wondering if someone knew of a tool (open-source or not) that is easier to use and boots off a USB keydrive. Ideally, it'll save the two commands to save/restore a partition, so I just need to boot the host from the USB key, choose the command, and it'll take care of business. Are there solutions that look like this? Thank you. Edit: Here's one among other articles that shows how to tell CZ to run a script to avoid the multiple screens.

  Read the article

• DISK BOOT FAILURE after upgrading power supply

  - by Phenom

  After upgrading my power supply, I get the following error message when trying to boot into Windows 7. DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER My Windows 7 installation is on a SATA hard drive. I'm able to fix this problem if I hook up my IDE hard drive, then it boots the SATA hard drive fine. I don't like this solution though because then that means my IDE hard drive is drawing power even though it isn't being used. Why would a newer power supply need the IDE hard drive hooked up just to boot into the SATA hard drive? There are no boot files on the IDE hard drive; it is completely empty. My old power supply did not need it hooked up in order to boot the SATA hard drive.

  Read the article

• hd0 out of disk error results to low graphics mode

  - by msPeachy

  Yesterday, I have reinstalled Ubuntu due to a error: hd0 out of disk on boot. Everything went fine, I've installed apps, perform updates and upgraded the kernel. I've even restarted it a few times just to check if I would encounter boot issues and was glad that everything was working perfectly, then powered it down. The next morning when I boot, I got this error: hd0 out of disk error. Press any key to continue... again! After pressing a key, it took 10 minutes for the Ubuntu logo to appear with it's 5 dots. After another 5 minutes, Ubuntu started checking the disk and displayed a message that / has errors, I pressed F to fix the errors. After which Ubuntu tells me that /tmp is not yet ready for mounting so I pressed S to skip mounting it, then Ubuntu restarted. On boot I saw the error: hd0 out of disk error. Press any key to continue... again. This time it took only a minute for the Ubuntu logo to appear and after another minute a dialog box appeared with the following message: The system is running in low-graphics mode. Your screen, graphics card, and input settings could not be detected correctly. You will have to configure these yourself. What would you like to do? Run in low-graphics mode for just one session Reconfigure graphics Troubleshoot the error Exit to console login Whichever option I choose I ended up with a console prompt: grub-editenv: error: cannot read the file /boot/grub/grubenv. _ I can't do anything on this console, whatever I type nothing happens. I've rebooted several times and I get same error every time. I don't quite understand what is wrong with Ubuntu or with my installation. I've encountered this hd0 out of disk error several times already and always ended up reinstalling. I'd really really appreciate it if you guys can help me fix this. Thank you and good day.

  Read the article

• Make a drive from one machine appear as a physical disk in another machine.

  - by Roberto Sebestyen

  I want to take a physical disk (or part of a disk) in one machine (call it machine-A) and I want to make it available in another machine (machine-B). But I don't want to map a network drive. I want it to appear in machine-B as a physical drive. Even though it is not a physical drive. The reason I want to do this is i want the ability to create shares in machine-B on that drive. Since I cannot do that on mapped drives, I need to use some utility that fools machine-B to think that it is a physical drive, and treat it as such. Both of these machines are windows server 2003. I heard about NFS, It sounds like what could be the solution to my problem. But isn't that a Linux/Unix protocol? What tools can I use to make this happen? Are there any open source solutions? I don't care what the solution is, as long as it achieves the end result, preferably open source solution though. Thanks for reading guys and gals!

  Read the article

• How does the process of disk partitioning actually work on most HDD's?

  - by Dark Templar

  From what I know of most laptops, you are able to "partition" your disk into as many other drives as you please. The more you cut it up, the smaller your partitions are, but from an organizational point of view, this may be desirable... I was wondering how the filesystem itself becomes partitioned underneath the partitions visible to the user. For instance, a laptop disk is usually divided into platters, each with two surfaces. The surfaces are further divided into "tracks". I guess what I am asking is, is it possible to identify how the disk itself keeps track of partitions? (whether each partition has its own platter? each partition has its own set of adjacent tracks? or some other configuration, or whether the data from different partitions are just randomly interleaved and scattered throughout the disk?)

  Read the article

• How to automatically take daily HDD backup?

  - by user13107

  I think my HDD might have crashed. I don't want to lose data if this happens again. I have dual boot Windows/Ubuntu system. What is the best way to backup data and other software settings in Ubuntu? I don't care much about Windows partition, important stuff is in Ubuntu. I have 1 Tb external HDD (laptop HDD is of 500 gb total). One way would be to run rsync every day (or via cronjob) to backup everything to external HDD. What might be better ways of achieving this (backup)? Also are instant backup software recommended? Are there any disadvantages of instant backup as opposed to daily rsync?

  Read the article

• Hard disk error

  - by Nadim A. Hachem

  I got this error during installation. "The installer encountered an error copying files to the hard disk: [Errno 5] Input/output error This is often due to a faulty CD/DVD disk or drive, or a faulty hard disk. It may help to clean the CD/DVD, to burn the CD/DVD at a lower speed, to clean the CD/DVD drive lens (cleaning kits are often available from electronics suppliers), to check whether the hard disk is old and in need of replacement, or to move the system to a cooler environment." how can i fix this and what does it mean specifically? i'm installing via usb so it can't be the CD. the laptop is recent so it cant be an old HD.

  Read the article

• Weird Ubuntu Desktop Boot Partition On External Hard Drive

  - by Magnitus

  I have a Thinkpad with Windows 7. Last time I installed an Ubuntu/Windows dual boot, Windows was never same after and regularly got corrupted so this time, I installed Ubuntu on a separate external hard drive. I took a 500 GB external hard drive and used Windows to shrink the partition on it to 400 GB, freeing 100 GB to install Ubuntu. Then I modified the booting priority of my computer to boot from the external hard drive if present. Then, I installed Ubuntu desktop on the external hard drive using a DVD, picked the most simplistic partitioning scheme I could get away with (didn't go auto as it didn't include the external hard drive as a choice) and voilà. Fast forward some time and I'm trying to refresh my understanding of Linux partitions to install a bunch of servers, so I'm looking at the current partitioning scheme on my external hard drive and find the boot partition puzzling... sda is my integrated hard drive with Windows 7. sdb is my Ubuntu desktop external hard drive. Running parted on sdb, I get this: (parted) print Model: WD My Passport 0740 (scsi) Disk /dev/sdb: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 393GB 393GB primary ntfs boot 2 393GB 500GB 107GB extended 5 393GB 425GB 32.8GB logical linux-swap(v1) 6 425GB 500GB 74.6GB logical ext4 At this point, I'm wondering why the ntfs partition is flagged as "boot" and not my ext4 partition which is the partition that contains / (and by extension, /boot since it's not on its own separate partition). Looking at mtab only confirms what I already know: eric@eric-ThinkPad-W530:~$ sudo cat /etc/mtab /dev/sdb6 / ext4 rw,errors=remount-ro 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 none /sys/fs/cgroup tmpfs rw 0 0 none /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 udev /dev devtmpfs rw,mode=0755 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 tmpfs /run tmpfs rw,noexec,nosuid,size=10%,mode=0755 0 0 none /run/lock tmpfs rw,noexec,nosuid,nodev,size=5242880 0 0 none /run/shm tmpfs rw,nosuid,nodev 0 0 none /run/user tmpfs rw,noexec,nosuid,nodev,size=104857600,mode=0755 0 0 none /sys/fs/pstore pstore rw 0 0 systemd /sys/fs/cgroup/systemd cgroup rw,noexec,nosuid,nodev,none,name=systemd 0 0 gvfsd-fuse /run/user/1000/gvfs fuse.gvfsd-fuse rw,nosuid,nodev,user=eric 0 0 /dev/sdb1 /media/eric/My\040Passport fuseblk rw,nosuid,nodev,allow_other,default_permissions,blksize=4096 0 0 My lack of understanding concerning this is not vital to anything (this is only my development desktop partition), but somehow annoys me. Any insight that could shed some light on this would be welcome.

  Read the article

• Somebody knows why the sectors of the IBM floppy disk are named 1 to 8 (and not 0 to 7 )

  - by Olivier Briand

  I am now programming on a 8 bits Z80 computer with CP/M 2.2, (as a hobby) and the floppy disk format is IBM, 40 tracks, 8 sectors per track, 512 bytes per sector. free space is 154 Ko on each face of the disk. Why the sectors are indexed 1 to 8 (and not zero to seven, as usually is seen with computers)? The catalog of the floppy disk is on the track 1 (sector 1 to 4, 64 entries). I'm wondering is the catalog on track zero? Is the zero track reserved to included a system (as track 0 & 1 are reserved to the system on a CP/M floppy disk, and catalog is on track 2)?

  Read the article

• Ubuntu will not boot without the pen-drive [closed]

  - by user71238

  Possible Duplicate: Can't boot without Flash Drive plugged in I've just installed Ubuntu on my PC and now it doesn't start unless I change the boot priority, if boot priority is my HD then it doesn't start and if boot priority is my pen-drive then it starts. If I remove my pen-drive, the system keep working normal, but if a restart my PC without the pen-drive, it will not start. Could someone help me?

  Read the article

• Power outage during disk wipe. What do I do now?

  - by Mark Trexler

  I was using Roadkil Diskwipe on an external hard drive and the power went out. I had removed it from any outlet connection by the time power was restored to prevent power-spike damage (it's on a surge protector, but I didn't want to rely on that). My question is, where do I go from here? Obviously I don't care about preserving any data currently on it, I just want to make sure the drive itself is not terminally damaged. I'm running chkdsk (full), but I don't know if that's the correct step to assessing any damage. If it makes any difference, the hard drive was unallocated at the time of the outage, as Diskwipe requires that for it to run. Also, could something like this cause latent problems with the drive itself (i.e. serious issues that I won't be aware of when testing it now). I'd appreciate any program recommendations if chkdsk is not the most appropriate diagnostic route. Thank you.

  Read the article

• I (stupidly) converted a TrueCrypt encrypted disk to GPT in Disk Management: now TrueCrypt won't mount it

  - by asilentfire

  Backstory: After moving a Macrium Reflect disk image from my TrueCrypt external drive (with whole disk encryption) onto a unencrypted drive and using Windows PE with Macrium Reflect to restore my internal disk to the recovery image on the external unencrypted drive, my Windows 8 failed to boot. I then went back and also recovered the System Partition (looking now, it is currently EFI), but I still couldn't boot into my backup.. I was in a hurry to get online for something so I just did a clean install of Windows 8, without the backup.. After I installed Windows 8, I went into Disk Management out of curiosity to see if there were other partitions with Windows 8 that Macruim might have missed, and there is (by default) a Recovery Partition of 100MB. My memory of this is hazy, as I was trying to get up and running for an exam at 4 AM: Something in Disk Management prompted me to convert my encrypted external drive to GPT.. I have no idea why I did this, but I went ahead and allowed it to convert my TrueCrypt drive to GPT. Now, I can't mount the drive in TrueCrypt.. Disk Management sees it as Disk 1, Basic, and Unallocated. I tried converting it back to MBR with Disk Management, but no dice with TrueCrypt :( If I try to mount the disk in TrueCrypt I get the message: Incorrect password or not a TrueCrypt volume I should never have messed with a Truecrypt drive in Disk Management, but I did. I have important college work in that drive, and fear I have lost it forever. PLEASE HELP

  Read the article

• PowerShell script to find files that are consuming the most disk space

  As you know, SQL Server databases and backup files can take up a lot of disk space. When disk is running low and you need to troubleshoot disk space issues, the first thing to do is to find large files that are consuming disk space. In this article I will show you a PowerShell script that you can use to find large files on your disks. 12 essential tools for database professionalsThe SQL Developer Bundle contains 12 tools designed with the SQL Server developer and DBA in mind. Try it now.

  Read the article

• External Hard disk not workng on windows after I formatted it on Ubuntu

  - by nav_jan

  I formatted my Western Digital 500 Gb hard disk on Ubuntu 10.4 and now I want to use it on Windows 7 but it cannot detect it. I formatted it with FAT(applicable to all) option. I tried to Google this problem a bit and as suggested by one of the site i tried to format this drive with NTFS. Still windows cannot detect it. Drives in windows 7 is not a problem because I tried a different usb drive on it and it works. I can see the led of the drive glow when I connect it and I can also see remove drive safely option in lower right corner, but i cannot see any option in "my computer" to access the hard disk. I am new to Ubuntu. Any help is appreciated.

  Read the article

• On Disk Substring index

  - by emeryc

  I have a file (fasta file to be specific) that I would like to index, so that I can quickly locate any substring within the file and then find the location within the original fasta file. This would be easy to do in many cases, using a Trie or substring array, unfortunately the strings I need to index are 800+ MBs which means that doing them in memory in unacceptable, so I'm looking for a reasonable way to create this index on disk, with minimal memory usage. (edit for clarification) I am only interested in the headers of proteins, so for the largest database I'm interested in, this is about 800 MBs of text. I would like to be able to find an exact substring within O(N) time based on the input string. This must be useable on 32 bit machines as it will be shipped to random people, who are not expected to have 64 bit machines. I want to be able to index against any word break within a line, to the end of the line (though lines can be several MBs long). Hopefully this clarifies what is needed and why the current solutions given are not illuminating. I should also add that this needs to be done from within java, and must be done on client computers on various operating systems, so I can't use any OS Specific solution, and it must be a programatic solution.

  Read the article

• Server 2008 Task Scheduler Mapped Drive Access C#

  - by user219313

  I'm trying do get Server 2008's Task Scheduler to run a C# console app which backs up data to a mapped backup drive somewhere on FastHosts network. I've written a test app which simply does this Directory.CreateDirectory("Z:\" + DateTime.Now.Ticks.ToString()); i.e. just creates a directory on the root of this Z drive. This works fine when I just run the .exe but when I schedule it in Task Scheduler it says the task has completed with return code 3762507597 - I can't find any info on what this means. I'm running the task with the highest Admin privelages as far as I can see.

  Read the article

• USB flash drive serial number specification

  - by clyfe

  I retrieve a USB flash drive serial number by means of ioctl HDIO_GET_IDENTITY as described here. Yet, for some flash drives there is no serial (for example my SanDisk Cruzer). Why some drives don not return a serial number? a) HDIO_GET_IDENTITY not implemented in driver ? b) They just don't have one ? c) Other ? (what?) Is there a specification (like IEEE) that describes where and how the serial number is stored inside the flash drive?

  Read the article

• how do i install a game patch on an external hard drive

  - by shadow

  I have a 2tb external hard drive and I want to install battlefield 1942 on it. i can get the game on the hard drive without problems, and it runs great. the problem is that i have an outdated version, and i need to install a patch. thats when it gets iffy. i get the patch and start the install, and it finishes, but it doesnt install to the game itself. it goes to its own seperate folder, and that does nothing to the game. the patch installer doesnt ask me where the game is, and so im thinking that it cant find the game itself, and then screws up. any help would be great!

  Read the article

• Booting from e-sata drive

  - by petersohn

  I have a HP EliteBook laptop (don't know exact product number), which has an internal hard drive with Windows installed on it. I have an external hard drive with e-sata and USB ports, linux installed on it. When I try to boot from the external drive, it works if I use USB but not if I use e-sata. In the BIOS setup, I have the following boot order set: External SATA drive USB Hard Drive Notebook Upgrade Bay Notebook Hard Drive etc. When I boot from another drive (such as the internal hard drive or from CD-ROM), and have the e-sata cable connected, it works perfectly. Is there any way to boot from the e-sata drive?

  Read the article

• HP DL380 G5 Predictive failure of a new drive

  - by CharlieJ

  Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

  Read the article

• Reinserted a RAID disk. Defined as foreign. Is import or clear the correct choice?

  - by Petrus

  I have re-inserted a RAID disk, on a DELL server with Windows Server 2008. The drive-status indicator was changing between a green and amber light, and the monitor gave the following message: There are offline or missing virtual drives with preserved cache. Please check the cables and ensure that all drives are present. Press any key to enter the configuration utility. I pressed a key and the PERC 6/I Integrated BIOS Configuration Utility showed that the RAID Status for that disk was Offline. After reinsertion of the disk the monitor is giving the following message: Foreign configuration(s) found on adapter. Press any key to continue or ‘C’ load the configuration utility, or press ‘F’ to import foreign configuration(s) and continue. After checking around on the net I am uncertain if I should choose import or clear. I cannot find out if an import means importing information from the array/system to the now foreign disk or the other way, i.e. importing information from the foreign disk to the array/system that was actually working fine. Also; if clear is a necessary thing to do ahead of a rebuild of that disk, or if clear means to clear the system to somehow make it ready to import the information from the foreign disk to the array/system, which is not what I want. I imagine that making the wrong choice here might be fatal. Please help clearing this out by telling what to choose and why.

  Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >