Search Results

Search found 12251 results on 491 pages for 'intel wireless card'.

Page 50/491 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

  • Wireless adapter won't enable

    - by user52141
    I bought a d-link dwa-125, plugged it in and windows recognized it right away and said everything was good to go. But there were no connection options. When I open up the network control panel and have it show me the adapters... the wireless adapter is greyed out and says it is disabled. So I tell it to enable. It says is it enabling, then says it is enabled... but the adapter stayed greyed out saying disabled. I am running 7 x64. I have reinstalled drivers, connected it via lan and had it update drivers.. same problem. It works just fine on any other computer in the house, just not this one.

    Read the article

  • Ubuntu 12.04 wireless detected, but can't connect to 128-bit WEP enabled microsoft MS-700 base station

    - by ubuntufan
    I installed Ubuntu 12.04 on a Presario R 3000. The Wireless card was not detected (firmware missing). Based on several related posts, I downloaded and installed the b43 driver and wireless was finally enabled. However, I am unable to connect to my base station successfully. The base station is configured for WEP 128-bit. I tried both infrastructure mode and ad-hoc mode (with the channel, band, etc. configured). Appreciate any help in trying to get past this.

    Read the article

  • Wired and Wireless Network Duplication

    - by Dave
    Howdy! Running into an issue when some of our client's have their laptop's connected via the wired ethernet network aswell as on the WLAN of the same network. There is know issues caused to the end clients.. BUT! Being a Managed Services Engineer i get pretty over the alerts that come through on our reports for machine's with the same hostname on the same network! We are not going to remove this monitoring because it does help a lot with detecting and stopping inferior users and things like that. So basically.. Question is, is there a way in Windows (third party programs welcome) to disable the wireless network when a wired network is connected and operational.. I know that Windows automticaly 'prefers' the wired network, however they are still both connected and therfore there is duplicate hostnames on the same network. Could also have stupid issues with DNS and things like that! Thanks!

    Read the article

  • Virtual Sd-card won't transfer [migrated]

    - by Hyztname
    I have a Verizon Galaxy Nexus 32GB. I've installed AOKP on it and it has been running pretty okay with no bugs etc... But after I connected it too my Nintendo Wii I think it mounted sdcard as FAT32 itself :\ I'm receiving the following error when trying to download something from 4Shared sync app(But actually none can download or transfer anything to Virtual sdcard): XXXXX.apk: open failed: EACCES(Permission denied) I already restored my old backup wiped all data etc, nothing seems to work. Note that I can access my sd-card, i can't only transfer, take pics... basically data. PS: I showed 4sync problem because it was the only one that specify something

    Read the article

  • My wireless network slows down every 7.5 minutes when my desktop is switched on

    - by Dog Ears
    My network has lag spikes lasting for a few seconds every 7.5 mins. The spikes also effect any other computer connected connected to my wirless router at the time. My wife has to connect her laptop via a cable to prevent the lag causing problems when she's VPNing into her work. If I switch my PC off the problem goes away! I've got an Edimax 7728ln 802.11n wireless card and Speedtouch 585v7 (I'm with Be) I've Tried... Updated the drivers from Edimax website: 2.0.3.0 (it does say 3.0.2.0 in devices properties though) WLAN Optimizer doesn't seem to be helping What can I do?

    Read the article

  • Are Intel and Motorola moving towards a MIPS/RISC model? [closed]

    - by Nick Rosencrantz
    Is it true what I read that Intel and Motorola are moving from CISC to a programming model more like RISC/MIPS? Why? From the famous book "Computer Architecture" by Hennessay which usually is recommended around here: Recent implementations of the x86 architecture actually translate x86 instruction into simple operation that look like MIPS instuctions.... Page 335. What does this mean specifically? Can you show me an example?

    Read the article

  • How to access an SD card from a virtual machine?

    - by Punit Soni
    I want to format an SD card from my Linux virtual machine. I have a built-in SD card reader in my laptop. I tried using VirtualBox and VMware Player and installed Ubuntu 10.04 guest. None of them are showing the SD card reader as a device. I can access the SD card from the Windows host. I am not interested in solutions using shared folders as I want to access the SD card as hardware (it should show up in /dev). I basically want to set up the SD card for BeagleBoard, but I don't want to install physical Ubuntu in my PC.

    Read the article

  • How to completely remove a wireless network setup from vista?

    - by 3d1l
    To remove a wireless connection setup I basically go to (network and sharing center) then select (manage wireless network) and then from the list of wireless networks I right click on the one that I want to remove and select (remove network) from the drop down menu. Problem is that when I go to define the wireless network again the system said that the network connection already exist so it seems that even when the wireless network definition is not longer display in the connections list, Vista keeps the configuration somewhere. So How can I be sure that a particular wireless network has been completely removed?

    Read the article

  • How should I troubleshoot a problematic wireless connection on Linux?

    - by Gearoid Murphy
    I recently purchased a netgear 150 usb wireless dongle for use with my 11.10 Xubuntu amd64 system. Using the network-manager interface, I can see local wireless networks and enter the authentication details for my local wireless lan. Unfortunately, the connection does not seem to work, I keep getting notifications that my wireless has disconnected (but none indicating that I've connected). When I examine syslog, it seems to indicate that I've successfully associated with the wireless switch and that dhcp has successfully acquired an ip address but the log shows that the dhcp process keeps sending requests, eventually dropping the connection. 'ifconfig wlan0' never shows the dhcp address logged in syslog. I suspect that the problem lies with the usb dongle, my configuration or the wireless switch but I am not certain how to isolate the problem, can anyone provide some insight on how I should go about homing in on the cause of this problem or verifying the functionality of the individual components, thanks.

    Read the article

  • How to install Intel VGA drive..?

    - by Ary Catur Wicaksono
    how to install intel VGA drive..?? I've been searching on google but did not see too I've been trying to ask the ubuntu forum in Indonesia. but they did not reply my post.. is there anything that can help me? *I am sorry my English is rather chaotic arthur@Chunx:~$ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10) arthur@Chunx:~$ sudo lshw -c display [sudo] password for arthur: *-display description: VGA compatible controller product: 82G33/G31 Express Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 10 width: 32 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:42 memory:fea80000-feafffff ioport:dc00(size=8) memory:e0000000-efffffff memory:fe900000-fe9fffff arthur@Chunx:~$ sudo apt-get install xserver-xorg-video-intel Sedang membaca daftar paket... Selesai Membangun pohon ketergantungan Membaca informasi yang tersedia... Selesai xserver-xorg-video-intel telah berada dalam versi terbaru. 0 dimutakhirkan, 0 baru terinstal, 0 akan dihapus dan 190 tidak akan dimutakhirkan.

    Read the article

  • Multiple Audio Issues

    - by Lerp
    I am having issues with my audio on Ubuntu 12.04, I will try and give as much detail as possible so sorry if there's too much detail. The Problem Audio plays from both speakers and headphone regardless of what connector I choose and regardless of the profile I use. The microphone is constantly being played through headphones & speakers. The headphone audio is extremely quiet but plays from both ears when I select "Headphones" for the connector in Sound Settings. The headphone audio only plays from one ear and is quiet (but not as quiet as above) when I select "Analogue Output" for the connector in Sound Settings. I can only select "Headphones" as the connector in Sound Settings if I set the profile to either "Analogue Stereo Output/Duplex", all others only allow me to choose "Analogue Output" for the connector. Despite the headphone sound issues, the speaker sound is fine apart from the fact that I am not able to select which output is used, they just both play. My headphone and microphone are plugged into the front and my speakers are plugged into the back. What I have tried I have put everything in alsamixer to 100 apart from "Front Mic Boost" which I have set to 0. Command Output aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: AD198x Digital [AD198x Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 2: AD198x Headphone [AD198x Headphone] Subdevices: 1/1 Subdevice #0: subdevice #0 arecord -l **** List of CAPTURE Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 2/3 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 Subdevice #2: subdevice #2 cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xf7ff8000 irq 70 cat /proc/asound/modules 0 snd_hda_intel cat /proc/asound/card*/codec* | grep "Codec" Codec: Analog Devices AD1989B cat /etc/modprobe.d/alsa-base.conf # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-ioctl32 ; /sbin/modprobe --quiet --use-blacklist snd-seq ; } # # Workaround at bug #499695 (reverted in Ubuntu see LP #319505) install snd-pcm /sbin/modprobe --ignore-install snd-pcm $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-pcm-oss ; : ; } install snd-mixer /sbin/modprobe --ignore-install snd-mixer $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-mixer-oss ; : ; } install snd-seq /sbin/modprobe --ignore-install snd-seq $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; /sbin/modprobe --quiet --use-blacklist snd-seq-oss ; : ; } # install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; } # Cause optional modules to be loaded above sound card driver modules install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-emu10k1-synth ; } install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq ; } # Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway) install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist saa7134-alsa ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options saa7134-alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 options snd-usb-audio index=-2 options snd-usb-caiaq index=-2 options snd-usb-ua101 index=-2 options snd-usb-us122l index=-2 options snd-usb-usx2y index=-2 # Ubuntu #62691, enable MPU for snd-cmipci options snd-cmipci mpu_port=0x330 fm_port=0x388 # Keep snd-pcsp from being loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 Hopefully I have provided enough information, I will happily provide anymore information needed. Thank you. Update Reinstalling alsa-base and pulseaudio fixed the headphone issues I was having.

    Read the article

  • Networking problems in VMWare with wireless bridge

    - by Robert Koritnik
    Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: wireless Guest network adapter 1: over Bridge VMNet (automatic) Guest network adapter 2: over Host only VMNet Problem When I surf the net within VM my internet connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitelly but connection won't pickup automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

    Read the article

  • Most transparent way to connect two LANS using a WET610N Wireless Bridge

    - by Spencer Ruport
    I have two wired systems hooked to a Linksys WRT54GL wired/wireless router which is also hooked to my internet. I'll refer to this as LAN1. I have two more systems in another room that are connected wirelessly. Recently I decided I would much rather have another wired LAN in the other room and use a bridge to connect them. This would be LAN2. Prior to hooking up the device I assumed that the ethernet side of the bridge would have a DHCP server so that I could simply hook it up to a switch and I'd be on my way. However that isn't the case which leads me to believe I'll have to add one to LAN2 correct? Or is there some way to have the DHCP from LAN1 also hand out IP addresses to LAN2? If I do need a DHCP device on LAN2 what would be best? Another hardware device or should I just install some DHCP software on one of the systems (since they're both on 24/7 anyway). Any recommendations would be appreciated. :)

    Read the article

  • Handheld Linux device can't see one wireless network

    - by Nathan
    I'm using a Nokia N810 running OS 2008 (version 5.2008.43-7; should be the latest). It can see networks up and down the street in my neighborhood and can connect to mine using WEP. I can also connect to free networks at restaurants and the like. When I bring it into work, it can't see a wireless network ("No connections available"). When I use netstumbler on my laptop I can see a list of several essids showing green connectivity for the network. I know that the network has its essid broadcast, and I know that it's unsecured. When I run iwlist wlan0 scan, I see several APs with no essid, but I don't see anything with an essid set. I have verified using iwlist that my hardware supports the correct channels and speeds. I know this isn't a Nokia/mobile forum, but it's running what's basically a Debian kernel. Any suggestions on what to do in this case? I'm really frustrated by this. Thanks, Nathan

    Read the article

  • Audio card with built-in ground isolator?

    - by Dave Jarvis
    What audio cards would you recommend that eliminate hum, and hard-drive & mouse movement signal interference? Hardware components: Motherboard. Asus P5Q SE Audio. Realtek ALC 1200, 8-Channel High-Definition Audio CODEC (on board) Harddrive. WD Caviar 320 GB Mouse. Logitech Marbleman USB Mixer. Mackie d.4 Pro Amplifier. Sonance Sonamp 260 All components are plugged into the same Monster Power HDP 910 powerbar (does not help eliminate noise). I have no other components plugged in. The computer uses a Monster iCable 1000 to go from mini (on board audio) to RCA (mixer). I have moved the cable as far from other cables as possible. A ground loop isolator between the mixer and on board audio eliminates all noise. I would rather not use a ground loop isolator; an internal audio card that is Linux-compatible (Kubuntu) would be ideal. Suggestions?

    Read the article

  • Setting up 802.1X wireless connection on OSX

    - by hizki
    I am an OSX user, I have Snow Leopard 10.6.5 and an updated AirPort (version 5.5.2). I am trying to connect to my university's wireless network, but it has a 802.1x security that I am having trouble defining... Here there are instructions for connecting with Windows XP, Windows 7 and Linux. Can someone please instruct me what should I do to set up this network on my Mac? I have had previous success in setting up this network, but I have no idea what I did that made it work. Since I updated my AirPort (to version 5.5.2) it worked only seldomly and very slowly... Before the update, even when it worked it never remembered my password. Update: I have already tried to create a new "location", removed all the 802.1x user profiles and all the remembered networks, and made sure the in the TCP/IP tab 'Configure IPv4' is set to "Using DHCP". I also moved /Library/Preferences/SystemConfiguration/preferences.plist to my desktop in attempt to force the system to create a new set of settings. Still I can define the connection to work.

    Read the article

  • Running Jackd on Ubuntu for my External Firewire Sound card

    - by Asaf
    Hello, I'm running Ubuntu 10.04 and I have an external Sound card: Phonic Firefly 302. I've connected the device, installed Jackd, added the lines: @audio - rtprio 99 @audio - memlock 500000 @audio - nice -10 to /etc/security/limits.conf logged out, logged back in, ran qjackctl (sudo qjackctl to be exact), ran the settings and chose "firewire" on the driver option, pressed "Start" and that was the output: 20:10:19.450 Patchbay deactivated. 20:10:19.578 Statistics reset. 20:10:19.601 ALSA connection graph change. 20:10:19.828 ALSA connection change. 20:10:21.293 Startup script... 20:10:21.293 artsshell -q terminate sh: artsshell: not found 20:10:21.695 Startup script terminated with exit status=32512. 20:10:21.695 JACK is starting... 20:10:21.695 /usr/bin/jackd -dfirewire -r44100 -p1024 -n3 jackd 0.118.0 Copyright 2001-2009 Paul Davis, Stephane Letz, Jack O'Quinn, Torben Hohn and others. jackd comes with ABSOLUTELY NO WARRANTY This is free software, and you are welcome to redistribute it under certain conditions; see the file COPYING for details 20:10:21.704 JACK was started with PID=22176. no message buffer overruns JACK compiled with System V SHM support. loading driver .. libffado 2.0.0 built Mar 31 2010 14:47:42 firewire ERR: Error creating FFADO streaming device cannot load driver module firewire no message buffer overruns 20:10:21.819 JACK was stopped successfully. 20:10:21.819 Post-shutdown script... 20:10:21.822 killall jackd jackd: no process found 20:10:22.230 Post-shutdown script terminated with exit status=256. 20:10:23.865 Could not connect to JACK server as client. - Overall operation failed. - Unable to connect to server. Please check the messages window for more info. Error: "/tmp/kde-asaf" is owned by uid 1000 instead of uid 0.

    Read the article

  • MicroSD card getting corrupted for no good reason

    - by ChaosR
    I recently bought an MicroSD card online. It's a Sandisk 16GB class 2. However, it has a nasty problem. Every time I fill it with my data, the fat tables get corrupted. I've tried reformatting it, blanking it, doesn't seem to solve the problem. I have tried windows and linux (ubuntu), both have the problem. I've used my usb microsd readers, and even tried putting it in my phone and putting data on it from there. All have this problem. Now the really odd thing is, besides the corrupted file tables, no programs can find anything wrong with the hardware. I've tried both chkdisk and "badblocks -w", neither give any type of error. Now I don't know if the actual data gets corrupted, or if its just filesystem tables. What happens is that one or more folders start showing a load of chinese-charred (random UTF8 symbols I suppose) folders and files, and it is impossible to do anything with those. All the other data (outside of the corrupted folders) seems fine. I've tried to test it, and the problem doesn't seem to show up until I fill the disk upto about 3~4GB. After that I can still access the data. But as soon as I eject/safely remove/unmount it, the bad things happen somehow. Next time I plug it in, the folders I most recently wrote to (but sometimes also the folders I wrote the time before last time to) are all gibberish. Does anybody have any clue what might be going on here? EDIT: It seems I can't even put ext3 or ext4 on it, they both complain about a corrupted journal. Gheh, guess something is really broken here.

    Read the article

  • Connect to Nonencrypted Wireless Network Using Ubuntu Commands

    - by Tim
    I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

    Read the article

  • how to set up dual wireless routers (G and N) with single broadband connection

    - by user15973
    A local cafe has an 802.11g wireless router attached to either an 8- or 12Mbs broadband connection. Although many customers still have -g devices, an increasing number are showing up with 802.11n devices (e.g. Mac laptops, iPads). The cafe owner is content with his router's area coverage, but he would like for his customers to be able to take advantage of the higher -n download speeds. He could simply replace the -g router with a -n router, but reportedly -n routers slow down considerably when servicing both -g and -n connections. Another option would be to buy the -n router, run an Ethernet cable between the two routers, and (of course) hook up the broadband connection to one of the two routers. Still another option would be to attach an ordinary, wired switch to the broadband connection and then attach both routers to the switch. Aside from the cost issue, what are the tradeoffs of those approaches? Which would you recommend, and why? Is there a better option than the ones I mentioned? Thank you in advance for your advice.

    Read the article

  • How to set TV-out options under Linux of an Geforce 9600 GT video card

    - by polemon
    I'm using the TV-out connector of my Geforce 9600 GT to connect it to an old TV set. It's obviously in Composite mode, the other two cables of Component video are dead, only Pb/VIDEO labeled one gives me a signal. The picture appears black/white on the TV, I presume it's because the video card gives me an NTSC signal, but it's a PAL tv set. How do I change the TV-out from NTSC to PAL? My Component to SCART adapter hasn't arrived yet, but I think I should be able to set manually, whether the signal should be Composite or Component. How do I switch modes of the TV-out, between Component and Composite? I'm running Linux, so it's probably some settings I need to make in xorg.conf. Edit: I got this far: I need to set in the "Device" section of my xorg.conf: Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" The whole section looks like this now: Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 9600 GT" Option "AddARGBGLXVisuals" "True" Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" EndSection How can I list all available settings for "TVStandard" and "TVOutFormat"?

    Read the article

  • Wired to wireless bridge in Linux

    - by adrianmcmenamin
    I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

    Read the article

  • Problems reviving old pc including graphics card issue.

    - by Mick
    I have a PC that seemed to have died years ago that I am trying to revive. It has a dual core athlon processor and a gigabyte motherboard. It had two dual output graphics cards, and I have long since forgotten which output would print out the diagnostic information as the PC starts up. Also I suspect that the resolution set on all the monitors was probably higher than my current single monitor is capable of displaying. The motherboard also has a built in graphics card, so I thought it may be simplest to remove both the graphics cards and plug my monitor into the onboard graphics just while I get things going. Does that seem sensible? Now the other problem: The PC has two hard drives. I have no idea which one is the primary one it is attempting to boot from. When I power up, the fan comes on and I hear some chuga-chuga-pause chuga-chuga-pause repeat indefinitely. I'm not sure which device is making the noise. There are no-beeps at any time. I see nothing on the screen at any time, not even for a second. Any suggestions? EDIT: If T start up the PC without the power connected to the CDrom there is no chuga-chugan noise.

    Read the article

  • Wireless Internet Connection Sharing in Ubuntu

    - by klutch2
    As the title states, I need to share a wireless connection with a laptop running Ubuntu as the AP. The setup will be as follows: Corporate WiFi <<== Laptop <<== Other Devices i.e. (iPad, iPhone) I want to be able to connect the "Other Devices" via WiFi to the laptop. I have thought of setting up an ad-hoc network by connecting to the Corporate WiFi and then setting up a new network and hoping the connection to both would stay, but that doesn't seem to work. If I set up the ad-hoc network by itself, I can see it from my "Other Devices". The reason I need this is because for some reason, my iPad and my iPhone will not connect to my corporate WiFi and I need to use them so I want to use my laptop to share the connection and act as an AP for my "Other Devices". My laptop is a Chrome CR-48 running Ubuntu and as some of you might know, it does not have an ethernet port, so having a wired connecting and then setting up a network is out of question. I want to connect to the Corporate WiFi and share that connection by having the laptop act as an AP for other devices.

    Read the article

  • MicroSD card getting corrupted for no good reason

    - by ChaosR
    I recently bought an MicroSD card online. It's a Sandisk 16GB class 2. However, it has a nasty problem. Every time I fill it with my data, the fat tables get corrupted. I've tried reformatting it, blanking it, doesn't seem to solve the problem. I have tried windows and linux (ubuntu), both have the problem. I've used my usb microsd readers, and even tried putting it in my phone and putting data on it from there. All have this problem. Now the really odd thing is, besides the corrupted file tables, no programs can find anything wrong with the hardware. I've tried both chkdisk and "badblocks -w", neither give any type of error. Now I don't know if the actual data gets corrupted, or if its just filesystem tables. What happens is that one or more folders start showing a load of chinese-charred (random UTF8 symbols I suppose) folders and files, and it is impossible to do anything with those. All the other data (outside of the corrupted folders) seems fine. I've tried to test it, and the problem doesn't seem to show up until I fill the disk upto about 3~4GB. After that I can still access the data. But as soon as I eject/safely remove/unmount it, the bad things happen somehow. Next time I plug it in, the folders I most recently wrote to (but sometimes also the folders I wrote the time before last time to) are all gibberish. Does anybody have any clue what might be going on here?

    Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >