Search Results

Search found 18341 results on 734 pages for 'neural network'.

Page 50/734 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

• vmware workstation - virtual network adapters missing from ipconfig, still show in networking (XP host)

  - by Adam

  Hi Folks - here's a new one for me, and my first time posting here: I installed VMWare workstation 7.1 on a new PC. VMWare properly installs the virtual network adapters under the Network Connections control panel, however for some reason they do not show up under ipconfig, which is very weird. They also don't appear anywhere in "route print". I don't have network connectivity to the VM. My guesses are perhaps some conflict with Symantec AntiVirus or Symantec Client Firewall. Tried the following things: enabling TCP/IP in the virtual network adapters (they often get installed with it disabled for some reason) Restoring defualts in the VMnetcfg gui tool (this causes an uninstall and reinstall of the virtual network adapters on the host) Re-installing vmware workstation Uninstalling checkpoint secureremote and then reinstalling vmware Just to be clear, this problem is totally on the host. In my searching for stuff about (non-vmware) adapters missing from ipconfig, I see some posts about resetting the TCP/IP stack using netsh. Looking into that next... Thanks!

  Read the article

• Linux - Block ssh users from accessing other machines on the network

  - by Sam

  I have set up a virtual machine on my network for uni project development. I have 6 team members and I don't want them to SSH in and start sniffing my network traffic. I already have set the firewall on my W7 pcs to ignore any connection attempts from the Virtual Machine, but would like to go a step further and not allow any network access from the VM to other machines on my network. Team members will be access the VM by SSH. The only external port forwarded is to vm:22. The VM is running in VirtualBox on a bridged network connection. Running latest Debian. If someone could tell me how to do this I would be much obliged.

  Read the article

• Corrupted network from ipad

  - by lisa

  All wireless clients were kicked off the network (3 PCs & 1 iPad). Only a PC with a wired connection was still able to connect. This morning I discovered that the network had been renamed and a new password had been assigned. Via Linksys Updater I gave a new password. Strangely, in my Windows Control Panel/Network connections our old password now exists as an unsecured network, that I cannot delete! When I attempt to connect using this bastard network, I get an Apple Push error. Linksys WRT610N PCs all using Windows 7 (wired & wireless) iPad 2

  Read the article

• Linux: how to verify my network configuration before doing a restart

  - by wael34218

  I am trying to build a network bridge for my VMs on a server. So I added a new file and changed another in the /etc/sysconfig/network-scripts directory. Then I did a network reboot with the following command:/etc/init.d/network restart After that the server was not up again. I contacted the hosting provider's support for help. I need a way to verify my new configuration before a network restart. I need to make sure that it will be up again, just like apache's /etc/init.d/httpd configtest

  Read the article

• Network Table assistance

  - by mitchnufc

  I am designing a small network and have came up with the following table I am just wondering if this seems right, would appreciate some feedback, thanks. Network/Router First IP Last IP Subnet Host Broadcast Router 1 162.10.0.1 162.10.0.7 255.255.255.248 162.10.0.0 162.10.0.8 Network 1 162.10.1.1 162.10.2.253 255.255.254.0 162.10.1.0 162.10.2.254 Network 2 162.10.0.9 162.10.0.14 255.255.255.248 162.10.0.8 162.10.0.15 Router 2 162.10.0.17 162.10.0.18 255.255.255.252 162.10.0.16 162.10.0.19 Network 3 162.10.0.21 162.10.0.146 255.255.255.128 162.10.0.20 162.10.0.147 Router one is the IP assigned by the ISP

  Read the article

• Taskbar Disappears Over Remote Desktop Connection When Outside Local Network

  - by CMikeB1

  I've got a machine on my home network running Windows Server 2012 (Based on Win8) and rather than attach a monitor I remote desktop in and it works fine on my local network. The problem is, when I try to access it from outside my local network the taskbar disappears completely. When I minimize an application rather than minimize to the taskbar it simply closes the window as small as it can as if the taskbar never existed (see photos at ). I've messed with the connection properties (show/hide desktop background, etc.) with no luck. I've used the following methods to remote in and they all are fine when on the local network and taskbar-less from outside: Remote Desktop Connection on Mac Remote Desktop Connection on Windows Jump Desktop on iOS using RDP To access the computer from outside my local network I'm using a Linksys router and mapping to the server IP, port 3389. See Photos: http://i.stack.imgur.com/FyUeQ.png http://i.stack.imgur.com/9MnVr.png

  Read the article

• Wireless internet is connected to an open network but has no internet

  - by Joshua Reeder

  I just installed Ubuntu on my laptop yesterday and it connected to the wireless fine. Then I took it to school, put it on their wired connection, downloaded some stuff, and now the wireless doesn't work. At first it would detect networks, but not connect. I restarted it and now it can connect, but it acts like it doesn't have internet in the browser. Wired connection still works fine on it. I know it isn't the network because my ipad is working on the wireless connection fine. I found another solution on here switching the security settings for the wireless, but this is the apartment's wireless so they have it open, and I won't be able to mess with it at all. Here is lspci output: 00:00.0 Host bridge: Intel Corporation Core Processor DMI (rev 11) 00:03.0 PCI bridge: Intel Corporation Core Processor PCI Express Root Port 1 (rev 11) 00:08.0 System peripheral: Intel Corporation Core Processor System Management Registers (rev 11) 00:08.1 System peripheral: Intel Corporation Core Processor Semaphore and Scratchpad Registers (rev 11) 00:08.2 System peripheral: Intel Corporation Core Processor System Control and Status Registers (rev 11) 00:08.3 System peripheral: Intel Corporation Core Processor Miscellaneous Registers (rev 11) 00:10.0 System peripheral: Intel Corporation Core Processor QPI Link (rev 11) 00:10.1 System peripheral: Intel Corporation Core Processor QPI Routing and Protocol Registers (rev 11) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 05) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 05) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 310M] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 07:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) 16:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 20) 16:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 20) 16:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 20) 16:00.4 System peripheral: JMicron Technology Corp. xD Host Controller (rev 20) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-Core Registers (rev 04) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 04) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 04) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 04) ff:03.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller (rev 04) ff:03.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Target Address Decoder (rev 04) ff:03.4 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Test Registers (rev 04) ff:04.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Control Registers (rev 04) ff:04.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Address Registers (rev 04) ff:04.2 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Rank Registers (rev 04) ff:04.3 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers (rev 04) ff:05.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Control Registers (rev 04) ff:05.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Address Registers (rev 04) ff:05.2 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Rank Registers (rev 04) ff:05.3 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers (rev 04) Update: I re-installed Ubuntu 12.04 (I assumed I messed something up while toying with it) but it did not solve the problem. Eventually, I got it to work with my school's wireless internet (the default network settings were wrong), but the internet still doesn't work on my apartment's wifi (it has no security on it).

  Read the article

• Problem adding "Network Policy and Access Services" role in Server 2008

  - by Django Reinhardt

  We are encountering an Error Code 0x80070643 when attempting to add the "Network Policy and Access Services" role on a fresh Windows Server 2008 R2 installation. Is there a known solution for this problem? Here is what information we have available so far: From ServerManager.log... 2504: 2009-11-23 11:12:01.712 [CBS] installing 'IAS NT Service RasServerAll RasRoutingProtocols ' ... 2504: 2009-11-23 11:12:01.911 [CBS] ...parents that will be auto-installed: 'RasServer ' 2504: 2009-11-23 11:12:01.912 [CBS] ...default children to turn-off: '<none>' 2504: 2009-11-23 11:12:01.924 [CBS] ...current state of 'IAS NT Service': p: Staged, a: Staged, s: UninstallRequested 2504: 2009-11-23 11:12:01.924 [CBS] ...setting state of 'IAS NT Service' to 'InstallRequested' 2504: 2009-11-23 11:12:01.935 [CBS] ...current state of 'RasServerAll': p: Staged, a: Staged, s: UninstallRequested 2504: 2009-11-23 11:12:01.935 [CBS] ...setting state of 'RasServerAll' to 'InstallRequested' 2504: 2009-11-23 11:12:01.946 [CBS] ...current state of 'RasRoutingProtocols': p: Staged, a: Staged, s: UninstallRequested 2504: 2009-11-23 11:12:01.946 [CBS] ...setting state of 'RasRoutingProtocols' to 'InstallRequested' 2504: 2009-11-23 11:12:01.956 [CBS] ...current state of 'RasServer': p: Staged, a: Staged, s: UninstallRequested 2504: 2009-11-23 11:12:01.956 [CBS] ...setting state of 'RasServer' to 'InstallRequested' 2504: 2009-11-23 11:12:01.967 [CBS] ...'IAS NT Service' : applicability: Applicable 2504: 2009-11-23 11:12:01.977 [CBS] ...'RasServerAll' : applicability: Applicable 2504: 2009-11-23 11:12:01.987 [CBS] ...'RasRoutingProtocols' : applicability: Applicable 2504: 2009-11-23 11:12:01.998 [CBS] ...'RasServer' : applicability: Applicable 2504: 2009-11-23 11:12:02.906 [CbsUIHandler] Initiate: 2504: 2009-11-23 11:12:02.906 [InstallationProgressPage] Installing... 2504: 2009-11-23 11:12:54.311 [CbsUIHandler] Error: -2147023293 : 2504: 2009-11-23 11:12:54.313 [CbsUIHandler] Terminate: 2504: 2009-11-23 11:12:54.316 [InstallationProgressPage] Verifying installation... 2504: 2009-11-23 11:12:54.326 [CBS] ...done installing 'IAS NT Service RasServerAll RasRoutingProtocols '. Status: -2147023293 (80070643) 2504: 2009-11-23 11:12:54.329 [NPAS] Skipped configuration of 'Network Policy Server' because install operation failed. 2504: 2009-11-23 11:12:54.330 [NPAS] Skipped configuration of 'Remote Access Service' because install operation failed. 2504: 2009-11-23 11:12:54.330 [NPAS] Skipped configuration of 'Routing' because install operation failed. 2504: 2009-11-23 11:12:54.330 [Provider] [STAT] ---- CBS Session Consolidation ----- [STAT] For 'Network Policy Server', 'Remote Access Service', 'Routing'[STAT] installation(s) took '52.616957' second(s) total. [STAT] Configuration(s) took '0.0004948' second(s) total. [STAT] Total time: '52.6174518' second(s). From System Event Viewer... Log Name: System Source: Service Control Manager Date: 23/11/2009 11:12:23 Event ID: 7023 Task Category: None Level: Error Keywords: Classic User: N/A Computer: Av7Analytics Description: The Network Policy Server service terminated with the following error: %%-2147013892 Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" /> <EventID Qualifiers="49152">7023</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2009-11-23T11:12:23.653578500Z" /> <EventRecordID>1317</EventRecordID> <Correlation /> <Execution ProcessID="468" ThreadID="2308" /> <Channel>System</Channel> <Computer>Av7Analytics</Computer> <Security /> </System> <EventData> <Data Name="param1">Network Policy Server</Data> <Data Name="param2">%%-2147013892</Data> </EventData> </Event> From Setup Event Viewer... Log Name: Setup Source: Microsoft-Windows-ServerManager Date: 23/11/2009 11:12:56 Event ID: 1616 Task Category: None Level: Error Keywords: User: AV7ANALYTICS\RenamedAdmin Computer: Av7Analytics Description: Installation failed. Roles: Network Policy and Access Services Error: Attempt to install Network Policy Server failed with error code 0x80070643. Fatal error during installation Error: Attempt to install Remote Access Service failed with error code 0x80070643. Fatal error during installation Error: Attempt to install Routing failed with error code 0x80070643. Fatal error during installation The following role services were not installed: Network Policy Server Routing and Remote Access Services Remote Access Service Routing Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Microsoft-Windows-ServerManager" Guid="{8C474092-13E4-430E-9F06-5B60A529BF38}" /> <EventID>1616</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x4000000000000000</Keywords> <TimeCreated SystemTime="2009-11-23T11:12:56.046431200Z" /> <EventRecordID>115</EventRecordID> <Correlation /> <Execution ProcessID="2504" ThreadID="2344" /> <Channel>Setup</Channel> <Computer>Av7Analytics</Computer> <Security UserID="S-1-5-21-2753803390-1569373846-1208217686-500" /> </System> <UserData> <EventXML xmlns:auto-ns3="http://schemas.microsoft.com/win/2004/08/events" xmlns="Event_NS"> <message> Roles: Network Policy and Access Services Error: Attempt to install Network Policy Server failed with error code 0x80070643. Fatal error during installation Error: Attempt to install Remote Access Service failed with error code 0x80070643. Fatal error during installation Error: Attempt to install Routing failed with error code 0x80070643. Fatal error during installation The following role services were not installed: Network Policy Server Routing and Remote Access Services Remote Access Service Routing </message> <identifiers>14, 206, 207, 208, 205</identifiers> </EventXML> </UserData> Thanks in advance for any help. It's quite shocking that we're already having problems with Microsoft's "latest and greatest".

  Read the article

• Norton Ghost EBAB03F1: The specified network name is no longer available

  - by Breck Carter

  After about 15 minutes, a Norton Ghost 14 backup fails with Error EBAB03F1: The specified network name is no longer available. The source computer is a P4 laptop running Windows XP SP3. The target computer is a Core2 Quad desktop running Windows Vista Ultimate 64bit. It does not help to disable Norton 360 on the source computer or Norton Antivirus 2008 on the target computer. The Event Viewer consistently shows the same two VSS-related errors after Norton Ghost starts but before it fails. It makes no difference if the VSS service is started or stopped. The VSS errors do not appear elsewhere in the event log, only after Ghost starts. The MSS event messages, however, are quite common, appearing throughout the log, and they may have nothing to do with the problem. Here is the Norton Ghost error display... -Errors exist. --Unable to write to file. ---Error EBAB03F1: The specified network name is no longer available. ---Unable to set file size. ----Error EBAB03F1: The specified network name is no longer available. ----Unable to write to file. -----Error EBAB03F1: The specified network name is no longer available. -----Unable to set file size. ------Error EBAB03F1: The specified network name is no longer available. Here are the source computer events, with the final error at the top and the "Ghost Starting" message at the bottom: ===== Event Type: Error Event Source: Norton Ghost Event Category: High Priority Event ID: 100 Date: 11/09/2009 Time: 9:40:26 AM User: N/A Computer: PAVILION2 Description: Error EC8F17B7: Cannot create recovery points for job: Drive Backup of (C:\) (3). Error E7D1001F: Unable to write to file. Error EBAB03F1: The specified network name is no longer available. Error E7D10046: Unable to set file size. Error EBAB03F1: The specified network name is no longer available. Error E7D1001F: Unable to write to file. Error EBAB03F1: The specified network name is no longer available. Error E7D10046: Unable to set file size. Error EBAB03F1: The specified network name is no longer available. Details: 0xEBAB0005 Source: Norton Ghost ===== Event Type: Information Event Source: MSSQL$SQLEXPRESS Event Category: Server Event ID: 3421 Date: 11/09/2009 Time: 9:34:06 AM User: NT AUTHORITY\NETWORK SERVICE Computer: PAVILION2 Description: Recovery completed for database ReportServer$SQLEXPRESSTempDB (database ID 6) in 1 second(s) (analysis 205 ms, redo 0 ms, undo 376 ms.) This is an informational message only. No user action is required. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 5d 0d 00 00 0a 00 00 00 ]....... 0008: 15 00 00 00 50 00 41 00 ....P.A. 0010: 56 00 49 00 4c 00 49 00 V.I.L.I. 0018: 4f 00 4e 00 32 00 5c 00 O.N.2.\. 0020: 53 00 51 00 4c 00 45 00 S.Q.L.E. 0028: 58 00 50 00 52 00 45 00 X.P.R.E. 0030: 53 00 53 00 00 00 18 00 S.S..... 0038: 00 00 52 00 65 00 70 00 ..R.e.p. 0040: 6f 00 72 00 74 00 53 00 o.r.t.S. 0048: 65 00 72 00 76 00 65 00 e.r.v.e. 0050: 72 00 24 00 53 00 51 00 r.$.S.Q. 0058: 4c 00 45 00 58 00 50 00 L.E.X.P. 0060: 52 00 45 00 53 00 53 00 R.E.S.S. 0068: 00 00 .. ===== Event Type: Information Event Source: MSSQL$SQLEXPRESS Event Category: Server Event ID: 17137 Date: 11/09/2009 Time: 9:34:02 AM User: NT AUTHORITY\NETWORK SERVICE Computer: PAVILION2 Description: Starting up database 'ReportServer$SQLEXPRESSTempDB'. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: f1 42 00 00 0a 00 00 00 ñB...... 0008: 15 00 00 00 50 00 41 00 ....P.A. 0010: 56 00 49 00 4c 00 49 00 V.I.L.I. 0018: 4f 00 4e 00 32 00 5c 00 O.N.2.\. 0020: 53 00 51 00 4c 00 45 00 S.Q.L.E. 0028: 58 00 50 00 52 00 45 00 X.P.R.E. 0030: 53 00 53 00 00 00 18 00 S.S..... 0038: 00 00 52 00 65 00 70 00 ..R.e.p. 0040: 6f 00 72 00 74 00 53 00 o.r.t.S. 0048: 65 00 72 00 76 00 65 00 e.r.v.e. 0050: 72 00 24 00 53 00 51 00 r.$.S.Q. 0058: 4c 00 45 00 58 00 50 00 L.E.X.P. 0060: 52 00 45 00 53 00 53 00 R.E.S.S. 0068: 00 00 .. ===== Event Type: Error Event Source: VSS Event Category: None Event ID: 5013 Date: 11/09/2009 Time: 9:28:32 AM User: N/A Computer: PAVILION2 Description: Volume Shadow Copy Service error: Shadow Copy writer ContentIndexingService called routine RegQueryValueExW which failed with status 0x80070002 (converted to 0x800423f4). For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 57 53 48 43 4f 4d 4e 43 WSHCOMNC 0008: 32 32 39 32 00 00 00 00 2292.... 0010: 57 53 48 43 49 43 00 00 WSHCIC.. 0018: 32 38 37 00 00 00 00 00 287..... ===== Event Type: Error Event Source: VSS Event Category: None Event ID: 5013 Date: 11/09/2009 Time: 9:28:32 AM User: N/A Computer: PAVILION2 Description: Volume Shadow Copy Service error: Shadow Copy writer ContentIndexingService called routine RegQueryValueExW which failed with status 0x80070002 (converted to 0x800423f4). For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 57 53 48 43 4f 4d 4e 43 WSHCOMNC 0008: 32 32 39 32 00 00 00 00 2292.... 0010: 57 53 48 43 49 43 00 00 WSHCIC.. 0018: 32 38 37 00 00 00 00 00 287..... ===== Event Type: Error Event Source: VSS Event Category: None Event ID: 12302 Date: 11/09/2009 Time: 9:28:32 AM User: N/A Computer: PAVILION2 Description: Volume Shadow Copy Service error: An internal inconsistency was detected in trying to contact shadow copy service writers. Please check to see that the Event Service and Volume Shadow Copy Service are operating properly. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 42 55 45 43 58 4d 4c 43 BUECXMLC 0008: 33 36 33 37 00 00 00 00 3637.... 0010: 42 55 45 43 58 4d 4c 43 BUECXMLC 0018: 33 36 30 37 00 00 00 00 3607.... ===== Event Type: Information Event Source: Norton Ghost Event Category: High Priority Event ID: 100 Date: 11/09/2009 Time: 9:27:57 AM User: N/A Computer: PAVILION2 Description: Info 6C8F1F63: The drive-based backup job, Drive Backup of (C:\) (3), has been started manually. Details: Source: Norton Ghost

  Read the article

• Windows Server 2008 R2 network adapter stops working, requires hard reboot

  - by Geoff Dalgas

  TL;DR version: Turns out this was a Windows Server 2008 R2 kernel networking bug. After siccing Microsoft support on it, we (eventually) got an unpublished kernel hotfix from Microsoft to address it. If you, too, are experiencing mysterious low-level network driver failures requiring a reboot/bluescreen cycle, you might want that hotfix (or maybe Service Pack 1 whenever it is released, too.) We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps. Switch Virtualization providers On the off chance this was related to Hyper-V in some way (we do host Linux VMs on it), we switched to VMWare Server. No change. Switch host model We've reached the end of our troubleshooting rope and are now formally involving Microsoft support. They recommended changing the host model: http://en.wikipedia.org/wiki/Host_model http://technet.microsoft.com/en-us/magazine/2007.09.cableguy.aspx We did that, and.. we'll see.

  Read the article

• How to Route Traffic in Case PPTP Remote Client is on Same Subnet as Server

  - by Marcus Cole

  I've a PPTP server setup on my local home network (192.168.1.0/24, pfSense). Now sometimes when I'm away and want to connect remotely my client (Windows 7) is also on the same network because e.g. the hotel has set it up the same way. Thus the connection works, but I can't reach any PC on my home network because everything is routed directly to the client local router which is in the same subnet. Is there a way to work around this by messing with a configuration or adapting Windows routing table, i.e. without modifying either network?

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• Disable Ethernet permanently to speed up boot time

  - by Anwar Shah

  I do not use the wired Ethernet Card. It seems to me that, Ubuntu is always trying in boot time to check the network via eth0, Which consumes some times and I guess this may slow down the boot process a bit. My dmesg output is below (partial) 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 1.985592] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input5 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 1.985651] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 1.985693] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 2.056261] firewire_core: created device fw0: GUID 00023f87af41fd7d, S400 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 3.710435] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null) A big time here..... 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 13.466642] ADDRCONF(NETDEV_UP): eth0: link is not ready 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.125296] Adding 1050620k swap on /dev/sda6. Priority:-1 extents:1 across:1050620k 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.226952] EXT4-fs (sda9): re-mounted. Opts: (null) 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.335012] snd_hda_intel 0000:00:1b.0: PCI INT A - GSI 22 (level, low) - IRQ 22 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.335091] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.335128] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.346410] input: Ideapad extra buttons as /devices/platform/ideapad/input/input6 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.428551] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.436958] cfg80211: Calling CRDA to update world regulatory domain 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.476550] Linux video capture interface: v2.00 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.486385] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (04f2:b008) So, My question is How can I disable the Ethernet card completely, so that kernel will not try to use that?

  Read the article

• mount network drive

  - by CaptnLenz

  since i updated my ubuntu to natty narwhal(from 10.04), my mount script doesn't work anymore. The scripts mounts a folder from a NAS (WD mybookworld) in the local network to a folder in my home folder. script looked like that: #!/bin/bash sudo mount //192.168.2.222/Public/Shared\ Music/ /home/simon/Musik/ error: mount: wrong fs type, bad option, bad superblock on //192.168.2.222/Public/Shared Music/, missing codepage or helper program, or other error (for several filesystems (e.g. nfs, cifs) you might need a /sbin/mount.<type> helper program) Manchmal liefert das Syslog wertvolle Informationen – versuchen Sie dmesg | tail oder so now, because the script doesn't work anymore i decided to add the mount-process to my fstab, because the network drive should be mounted on every startup. My fstab entry looks like this: //192.168.2.222/Public/Shared\ Music/ /home/simon/Musik cifs credentials=/home/simon/.smbcredentials 0 0 But it doesn't work, too. I get a message during the startup process, that Musik couldn't be mounted. Are there any log files i can check for errors? The system is a fresh installed 11.04. Greetings

  Read the article

• Designing a social network with CQRS, graph databases and relational databases in mind

  - by Siraj Mansour

  I have done quite an amount of research on the topic so far, but i couldn't come up with a conclusion to make up my mind. I am designing a social network and during my research i stumbled upon graph databases, i found neo4j pretty interesting for user relations and traversing through nodes. I also thought of using a relational database such as MS-SQL or MySQL to store entity data only and depending on neo4j for connections between entities. Of course this means more work in my application to store and pull data in and out of 2 different sources. My first question : Is using this approach (graph + relational) a good approach for designing my social network keeping in mind that users on social networks don't have to in synch with real data by split second ? What are the positives and negatives of this approach ? My Second question : I've been doing some reading on CQRS and as i understood it is mostly useful for collaborative environments, and environments where users see a lot of "stale" data. social networks has shared comments, events, etc .. and many users query or update the same data. Could CQRS be a helpful approach ? Would it give any performance/scalability benefits or non-useful complexity ? Is it fairly applicable with my possible choice of (graph + relational) databases approach mentioned in the question above ? My purpose is to know if the approaches i have mentioned above seem good enough for the business context.

  Read the article

• Layer 2 topology discovery

  - by pegah s

  I have been given a network (it is a LAN) comprised of switches and I need to discover the topology of that. (There may be Link Aggregation Groups (LAGs) in the network as well.) I have done a lot of search on layer 2 topology discovery and I have seen many articles talking about using SNMP MIBs or LLDP (I do not know which one is better or more practical, but all devices in my network support SNMP). But my problem is that I cannot find "the software to install and run" to actually see the topology map. I would really appreciate if someone could send me the website where I can download the code and use it. I have also found a lot of tools available online such as OpenNMS, Nagios, The Dude, LANsurveyor, SNMPwalk, and many more... But I cannot figure out which one is the best to pick. To summarize: what is the easiest simplest way to discover the layer 2 network topology?

  Read the article

• Windows 7 "Backup completed but some files were skipped"

  - by Andrew Coleson

  I set up Windows 7 Pro to backup my files to a network path (woohoo!) and chose to backup "data for newly created users, libraries", and my user folder (no system image). All went fine (although the first backup took ~12 hours for some ridiculous reason), but at the end it gave me a message that "Your backup completed, but some files were skipped. Click to see which files." I checked and the "files" skipped were my 3 network-mapped drives, which is perfectly fine and reasonable behavior (I certainly don't need it to back up my network-mapped drives as part of my local PC backup), but in the Backup and Restore center it warns me that my Last backup was "Never" and the Action Center now has a permanent "Check your backup results" issue. Is there any way to set up the backup to exclude the network-mapped drives or tell it that I really don't mind that it skipped drives I never asked it to back up?

  Read the article

• Hardening network with sysctl settings made Wi-fi downloading speed extremely slow

  - by Rohit Bansal

  I just followed up following steps to harden network security The /etc/sysctl.conf file contain all the sysctl settings. Prevent source routing of incoming packets and log malformed IP's enter the following in a terminal window: sudo vi /etc/sysctl.conf Edit the `/etc/sysctl.conf` file and un-comment or add the following lines : # IP Spoofing protection net.ipv4.conf.all.rp_filter = 1 net.ipv4.conf.default.rp_filter = 1 # Ignore ICMP broadcast requests net.ipv4.icmp_echo_ignore_broadcasts = 1 # Disable source packet routing net.ipv4.conf.all.accept_source_route = 0 net.ipv6.conf.all.accept_source_route = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv6.conf.default.accept_source_route = 0 # Ignore send redirects net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.default.send_redirects = 0 # Block SYN attacks net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_max_syn_backlog = 2048 net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_syn_retries = 5 # Log Martians net.ipv4.conf.all.log_martians = 1 net.ipv4.icmp_ignore_bogus_error_responses = 1 # Ignore ICMP redirects net.ipv4.conf.all.accept_redirects = 0 net.ipv6.conf.all.accept_redirects = 0 net.ipv4.conf.default.accept_redirects = 0 net.ipv6.conf.default.accept_redirects = 0 # Ignore Directed pings net.ipv4.icmp_echo_ignore_all = 1 To reload sysctl with the latest changes, enter: sudo sysctl -p But, after applying the changes I found "Wi-fi" downloading speed and terminal downloading speed extremely slow (less than 1KB/s) however surfing speed through browser was good. But, using direct ethernet cable was giving a good speed. Then, I reverted back the above changes and things fall back in line once again.... Could you please let me know what possibly in above script is affecting such behaviour [and why] ? How could I still maintain hardening of network security without disturbing Wi-fi downloading speed ?

  Read the article

• How can access files on shared drive from Windows 2008 server configured with SFTP

  - by communicator

  I have installed OpenSSH on my windows 2008 server by following the user guide here . Now I have some files on windows network share with UNC path as \\corp\test\testdata I want map this file system on network share to my windows 2008 server which is configred with SFTP so that I can access these files from my Java Program by doing SFTP to windows 2008 server.Is there anyway I can map the network share to C or other drive in server so that all the files on the share will be available as local files on the server?

  Read the article

• Using VLANs that are routed together?

  - by dannymcc

  I have a quick question that's bugging me the more I read about VLANs. So far I understand that they are useful for dividing the network into sub-sections, but if you route them together does that not remove any security benefit? As an example, if I created a VLAN on my home network which was simply one computer, one server and one router.if I wanted to divide the network between computers and servers I could put the computer on VLAN 10 and the server on VLAN 20. Then the computer would no longer be able to communicate with the server - unless I added a static route to the router that connected the two together, basically telling VLAN 10 that VLAN 20 exists and how to communicate with it. The VLANs would then be connected in a similar way to a 'flat' network that has no VLANs. Therefore, surely, all security benefits are lost. Am I missing something?

  Read the article

• Is there an equivalent command for 'init.d/networking restart' in OS X

  - by l0c0b0x

  From time to time, I've encountered issues with OS X clients' network connections (Wired and Wireless, Leopard/Snow Leopard) where nothing will fix the issue, until you reboot. Is there a particular 'network service/process' I should be watching out for? I was thinking it would be useful to know of a command that will reset a 'network connection' type service/process (same as running a sudo /etc/init.d/networking restart). Thanks!

  Read the article

• Can't access to Ubuntu Shared Folder from Windows XP

  - by See hyung Lee

  I've set up a Ubuntu Shared Folder for around 70 users. They all use XP and most of them can access to the folder. Only few encounter some error message when they try to access to it. is not accessible. you might not have permission to use this network resource the network is not present or not started All 70 users same version of XP and in 192.168.1.0 /24 network. What'd be the problem?

  Read the article

• Getting my brother MFC-J825DW working as a network scanner

  - by AntonChanning

  I've been attempting to set up my new brother multi-function device to work as a printer and scanner using the following steps. It is connected to the network as a LAN device, not directly connected to my ubuntu machine. Downloaded the lpr driver and cupswrapper driver from Brother support. (Select the deb packages, not the rpms). Followed the instructions to install the lpr driver. Followed the instructions to install the cupswrapper driver. After this point I was able to successfully perform a test print, so the printer part is working. So far I haven't had much luck getting the scanner working. This is what I've tried: Downloaded the brscan4 and scan-key-tool deb packages from brother support. Followed the instructions for installing the scanner driver for network. Followed the instructions for installing scan-key-tool. However when I tried to scan it detects no scanner. I then tried the solution offered in this answer to a question based on a similar brother printer, but no luck. I must have made a mistake somewhere along the line. Does anyone have any ideas what I can try to find out what? Or should I uninstall everything and start again from the beginning?

  Read the article

• How have multiple web servers and IPs on the same physical network

  - by jsigned

  I do web development out of a small office and need to have multiple physical and virtual servers that can be accessed from the internet. I also have a number of devices (computers, laptops, tablets, printers, etc) that need connections as well. I have gotten a subnet of 8 IP's from my ISP and while that is adequate for the web servers its far too small for everything that needs access to the network. My router is an ASUS RT-N16 running DD-WRT. I'm just smart enough about this routing topic to be dangerous, think 2 year old with a magic marker. I would like to keep my internal network NAT'ed on the 192.168.x.x network and route the 68.69.x.x 255.255.255.248 traffic directly to the servers. The physical network consists of the 4 port DD-WRT router and an unmanaged gig switch. I have a fiber connection to the office that works as an Ethernet port. In other words I can plug my laptop directly into it and have access to the internet. There is no login or password and the router is setup to get DHCP from the ISP, and to provide DHCP addresses for the internal network. What I've done so far is google and try different configurations with little success. In the end I decided I didn't even know how to ask the questions needed. My questions are: Is this the best way to configure the network? How do you do it? VLANs? Multiple routers? I've never had to configure a router using anything more than the GUI so if this is command line stuff be gentle.

  Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >