Search Results

Search found 18341 results on 734 pages for 'neural network'.

Page 53/734 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

  • Network switching issues with MacOS 10.7?

    - by Denis
    I'm having a wired problem and hope somebody can tip me, what way should I dig to. I'm using MacBookPro with Lion 10.7.3 both at my working place & at home. At working place, we have a domain-based network with 802.1x authorization (more than 400 computers) and to connect it I'm using Ethernet cable. IP range is 10.10.2.*. All network settings are setup automatically by DHCP. Also, in settings, I have Network Account Server setup in the User&Groups Settings for my work Domain server - and it is available only from corporate network. At home, I have an ADSL router, that shares Internet connection by WiFi in NAT mode. I'm using WiFi to connect it. Router gives out addresses from 192.168.1.* range and all settings are also set up by router's DHCP. So, my problem is the following. When I come back home from the office, I open my MacBook and AirPort automatically connects my WiFi network. After this, for about 1 minute I'm able to browse sites & ping hosts successfully. But after this minute, network connection is broken down. All pings return time-out. trace route to google.com stops on 192.168.1.1 (which is my router). This lasts for 3-4 minutes. After that network connection is automatically repaired and all pings go smoothly again. At the same time, when my MacBook return timeouts, I can successfully ping any host from my wife's MacBook - so this doesn't look like router issue. When I come to the office, I don't have any issues and Internet connection is available & stable moments after ethernet cable plugged in. Do anybody has any clues about this? What should I monitor & what settings look for resolving this issue? Please, ask, what additional information should I provide. Hoping for good advice & thanks in advance!

    Read the article

  • tc rules block traffic from some hosts at network

    - by user139430
    I have a problem I can not solve. The script, which sets the rules for traffic shaping is blocking the traffic from some hosts.If I remove all the rules, then it works. I can not understand why? Here is my script... #!/bin/sh cmdTC=/sbin/tc rateLANDl="60mbit" ceilLANDl="60mbit" rateLANUl="40mbit" ceilLANUl="40mbit" quantLAN="1514" # Nowaday bandwidth limit set to 100mbit. # We devide it with 60mbit download and 40mbit upload bandthes. rateHiDl="30mbit" ceilHiDl="60mbit" rateHiUl="20mbit" ceilHiUl="40mbit" quantHi="1514" rateLoDl="30mbit" ceilLoDl="60mbit" rateLoUl="20mbit" ceilLoUl="40mbit" quantLo="1514" devNIF=eth0 devFIF=ifb0 modprobe ifb ip link set $devFIF up 2>/dev/null #exit 0 ################################################################################################ # Remove discuiplines from network and fake interfaces ################################################################################################ $cmdTC qdisc del dev $devNIF root 2>/dev/null $cmdTC qdisc del dev $devFIF root 2>/dev/null $cmdTC qdisc del dev $devNIF ingress 2>/dev/null if [ "$1" = "down" ]; then exit 0 fi ################################################################################################ # Create discuiplines for network interface ################################################################################################ $cmdTC qdisc add dev $devNIF root handle 1:0 htb default 12 # Create classes for network interface $cmdTC class add dev $devNIF parent 1:0 classid 1:1 htb rate ${rateLANDl} ceil ${ceilLANDl} quantum ${quantLAN} $cmdTC class add dev $devNIF parent 1:1 classid 1:11 htb rate ${rateHiDl} ceil ${ceilHiDl} quantum ${quantHi} $cmdTC class add dev $devNIF parent 1:1 classid 1:12 htb rate ${rateLoDl} ceil ${ceilLoDl} quantum ${quantLo} $cmdTC qdisc add dev $devNIF parent 1:11 handle 111: sfq perturb 10 $cmdTC qdisc add dev $devNIF parent 1:12 handle 112: sfq perturb 10 # Create filters for network interface $cmdTC filter add dev $devNIF protocol all parent 1:0 u32 match ip dst 10.252.2.0/24 flowid 1:11 $cmdTC filter add dev $devNIF protocol all parent 111: handle 111 flow hash keys dst divisor 1024 baseclass 1:11 $cmdTC filter add dev $devNIF protocol all parent 112: handle 112 flow hash keys dst divisor 1024 baseclass 1:12 ################################################################################################ # Create discuiplines for fake interface ################################################################################################ $cmdTC qdisc add dev $devFIF root handle 1:0 htb default 12 # Create classes for network interface $cmdTC class add dev $devFIF parent 1:0 classid 1:1 htb rate ${rateLANUl} ceil ${ceilLANUl} quantum ${quantLAN} $cmdTC class add dev $devFIF parent 1:1 classid 1:11 htb rate ${rateHiUl} ceil ${ceilHiUl} quantum ${quantHi} $cmdTC class add dev $devFIF parent 1:1 classid 1:12 htb rate ${rateLoUl} ceil ${ceilLoUl} quantum ${quantLo} $cmdTC qdisc add dev $devFIF parent 1:11 handle 111: sfq perturb 10 $cmdTC qdisc add dev $devFIF parent 1:12 handle 112: sfq perturb 10 # Create filters for network interface $cmdTC filter add dev $devFIF protocol all parent 1:0 u32 match ip src 10.252.2.0/24 flowid 1:11 $cmdTC filter add dev $devFIF protocol all parent 111: handle 111 flow hash keys src divisor 1024 baseclass 1:11 $cmdTC filter add dev $devFIF protocol all parent 112: handle 112 flow hash keys src divisor 1024 baseclass 1:12 ################################################################################################ # Create redirect discuiplines from network to fake interface ################################################################################################ $cmdTC qdisc add dev $devNIF handle ffff:0 ingress $cmdTC filter add dev $devNIF parent ffff:0 protocol all u32 match u32 0 0 action mirred egress redirect dev $devFIF Here is my /etc/modules: loop ifb ppp_mppe nf_conntrack_pptp nt_conntrack_proto_gre nf_nat_pptp nf_nat_proto_gre The system is Linux wall 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux

    Read the article

  • Week 21: FY10 in the Rear View Mirror

    - by sandra.haan
    FY10 is coming to a close and before we dive into FY11 we thought we would take a walk down memory lane and reminisce on some of our favorite Oracle PartnerNetwork activities. June 2009 brought One Red Network to partners offering access to the same virtual kickoff environment used by Oracle employees. It was a new way to deliver valuable content to key stakeholders (and without the 100+ degree temperatures). Speaking of hot, Oracle also announced in June new licensing options for our ISV partners. This model enables an even broader community of ISVs to build, deploy and manage SaaS applications on the same platform. While some people took the summer off, the OPN Program team was working away to deliver a brand new partner program - Oracle PartnerNetwork Specialized - at Oracle OpenWorld in October. Specialized. Recognized. Preferred. If you haven't gotten the message yet, we may need an emergency crew to pull you out from that rock you've been hiding under. But seriously, the announcement at the OPN Forum drew a big crowd and our FY11 event is shaping up to be just as exciting. OPN Specialized was announced in October and opened our doors for enrollment in December 2009. To mark our grand opening we held our first ever social webcast allowing partners from around the world to interact with us live throughout the day. We had a lot of great conversations and really enjoyed the chance to speak with so many of you. After a short holiday break we were back at it - just a small announcement - Oracle's acquisition of Sun. In case you missed it, here is a short field report from Ted Bereswill, SVP North America Alliances & Channels on the partner events to support the announcement: And while we're announcing things - did we mention that both Ted Bereswill and Judson Althoff were named Channel Chiefs by CRN? Not only do we have a couple of Channel Chiefs, but Oracle also won the Partner Program 5 Star Programs Award and took top honors at the CRN Channel Champion Awards for Financial Factors/Financial Performance in the category of Data and Information Management and the and Xchange Solution Provider event in March 2010. We actually caught up with Judson at this event for a quick recap of our participation: But awards aside, let's not forget our main focus in FY10 and that is Specialization. In April we announced that we had over 35 Specializations available for partners and a plan to deliver even more in FY11. We are just days away from the end of FY10 but hope you enjoyed our walk down memory lane. We are already planning lots of activity for our partners in FY11 starting with our Partner Kickoff event on June 29th. Join us to hear the vision and strategy for FY11 and interact with regional A&C leaders. We look forward to talking with you then. The OPN Communications Team

    Read the article

  • PPTP VPN connects via NM but goes down during SSH connection

    - by Andrea Olivato
    I setup a VPN PPTP connection via network manager and it connects correctly (I see the lock near the notification icon and the message "Vpn connection has been successfully...") As soon as I try to perform any SSH connection via the established tunnel the connection itself goes down with the message "Vpn connection failed". the SSH connection always fails at debug1: SSH2_MSG_KEXINIT sent I've looked into the system logs and this is the log Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> Starting VPN service 'pptp'... Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 7093 Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' appeared; activating connections Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: init (1) Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: starting (3) Dec 12 12:25:00 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (Connect) reply received. Dec 12 12:25:05 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (IP4 Config Get) reply received from old-style plugin. Dec 12 12:25:05 ushuaia NetworkManager[1155]: <info> VPN Gateway: 5.98.141.210 Dec 12 12:25:06 ushuaia NetworkManager[1155]: <info> VPN connection 'Redation' (IP Config Get) complete. Dec 12 12:25:06 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: started (4) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: stopping (5) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state changed: stopped (6) Dec 12 12:25:14 ushuaia NetworkManager[1155]: <info> VPN plugin state change reason: 0 Dec 12 12:25:15 ushuaia NetworkManager[1155]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Dec 12 12:25:20 ushuaia NetworkManager[1155]: <info> VPN service 'pptp' disappeared Please note that the same vpn is configured on my colleagues Windows 7 and works without problem when they use putty to connect via SSH

    Read the article

  • Problem getting GOBI 2000 HS to work

    - by Zypher
    I've been trying to get my integrated GOBI WWAN card to work under 10.10 for a while now. I was able to get the network manager to see the card after installing the gobi-loader package. I was able to setup the connection, but i cannot establish a connection to Verizon. Below is the output from /var/log/daemon.log as i try to connect. Oct 19 14:29:42 gbeech-x201 AptDaemon: INFO: Quiting due to inactivity Oct 19 14:29:42 gbeech-x201 AptDaemon: INFO: Shutdown was requested Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) starting connection 'Verizon connection' Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 3 -> 4 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 4 -> 6 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete. Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 6 -> 4 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <warn> CDMA connection failed: (32) No service Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 4 -> 9 (reason 0) Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Marking connection 'Verizon connection' invalid. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <warn> Activation (ttyUSB0) failed. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 9 -> 3 (reason 0) Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): deactivating device (reason: 0). Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Policy set 'Auto SO-GUEST' (wlan0) as default for IPv4 routing and DNS. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Policy set 'Auto SO-GUEST' (wlan0) as default for IPv4 routing and DNS.

    Read the article

  • Ubuntu 12 crashed and took down network

    - by Leopd
    We recently set up a new Ubuntu 12.04LTS server on our network. It's not fully configured so it's not doing much beyond sshd and a default apache2 install. But this evening it appears to have crashed. It wasn't responding to the network or the keyboard. But the worst part is, it took down the entire network. My knowledge of the network stack below OSI layer 3 is very limited, so the rest confuses me. When this machine was physically connected to the network, no other machine could connect to the outside internet. When things were broken, running arp showed that our gateway's IP address (10.0.1.1) was listed as "invalid." Unplugging the server from the network fixed the problem, and plugging it back in broke it again. So the crashed server was advertising itself as owning the gateway's IP address? There's nothing at all in syslog during the time when it was causing problems. Any ideas about how to figure out what went wrong or what we can do to prevent it from happening again? I'm hesitant to even put the machine back on the network right now. Update ** It crashed again, and I ran tcpdump -penn arp (thanks bahamat!) for several minutes and got this... (timestamps and duplicate lines removed) 00:1e:65:f8:dc:24 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.1 tell 10.0.2.191, length 46 00:1e:65:f8:dc:24 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.44 tell 10.0.2.191, length 46 60:d8:19:d4:71:d6 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.1 tell 10.0.2.125, length 46 d4:9a:20:04:e9:78 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.100, length 28 Update 2 ** When the network is functioning properly, arping -c4 10.0.1.1 returns this: ARPING 10.0.1.1 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=0 time=267.982 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=1 time=422.955 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=2 time=299.215 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=3 time=366.926 usec --- 10.0.1.1 statistics --- 4 packets transmitted, 4 packets received, 0% unanswered (0 extra) When the bad server is plugged in, arping -c4 10.0.1.1 returns: ARPING 10.0.1.1 --- 10.0.1.1 statistics --- 4 packets transmitted, 0 packets received, 100% unanswered (0 extra) Context ** 10.0.x.x is the main subnet. 10.0.1.1 is the main internet gateway 10.0.1.44 is a printer 10.0.2.* devices are all laptops / workstations I have no idea what's using the 192.168.x.x subnet -- your guesses are at least as good as mine. A VM on a workstation? A misconfigured WAP? Somebody re-sharing wifi? A machine that failed to DHCP? The offending ubuntu server's MAC address ends in cd:80 so isn't listed in the dump. It should DHCP to 10.0.3.3 Thanks for any help. This ARP stuff is all voodoo to me. Packets just go to IP addresses, right? ;)

    Read the article

  • Proper network configuration for a KVM guest to be on the same networks at the host

    - by Steve Madsen
    I am running a Debian Linux server on Lenny. Within it, I am running another Lenny instance using KVM. Both servers are externally available, with public IPs, as well as a second interface with private IPs for the LAN. Everything works fine, except the VM sees all network traffic as originating from the host server. I suspect this might have something to do with the iptables-based firewall I'm running on the host. What I'd like to figure out is: how to I properly configure the host's networking such that all of these requirements are met? Both host and VMs have 2 network interfaces (public and private). Both host and VMs can be independently firewalled. Ideally, VM traffic does not have to traverse the host firewall. VMs see real remote IP addresses, not the host's. Currently, the host's network interfaces are configured as bridges. eth0 and eth1 do not have IP addresses assigned to them, but br0 and br1 do. /etc/network/interfaces on the host: # The primary network interface auto br1 iface br1 inet static address 24.123.138.34 netmask 255.255.255.248 network 24.123.138.32 broadcast 24.123.138.39 gateway 24.123.138.33 bridge_ports eth1 bridge_stp off auto br1:0 iface br1:0 inet static address 24.123.138.36 netmask 255.255.255.248 network 24.123.138.32 broadcast 24.123.138.39 # Internal network auto br0 iface br0 inet static address 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 bridge_ports eth0 bridge_stp off This is the libvirt/qemu configuration file for the VM: <domain type='kvm'> <name>apps</name> <uuid>636b6620-0949-bc88-3197-37153b88772e</uuid> <memory>393216</memory> <currentMemory>393216</currentMemory> <vcpu>1</vcpu> <os> <type arch='i686' machine='pc'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='cdrom'> <target dev='hdc' bus='ide'/> <readonly/> </disk> <disk type='file' device='disk'> <source file='/raid/kvm-images/apps.qcow2'/> <target dev='vda' bus='virtio'/> </disk> <interface type='bridge'> <mac address='54:52:00:27:5e:02'/> <source bridge='br0'/> <model type='virtio'/> </interface> <interface type='bridge'> <mac address='54:52:00:40:cc:7f'/> <source bridge='br1'/> <model type='virtio'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' keymap='en-us'/> </devices> </domain> Along with the rest of my firewall rules, the firewalling script includes this command to pass packets destined for a KVM guest: # Allow bridged packets to pass (for KVM guests). iptables -A FORWARD -m physdev --physdev-is-bridged -j ACCEPT (Not applicable to this question, but a side-effect of my bridging configuration appears to be that I can't ever shut down cleanly. The kernel eventually tells me "unregister_netdevice: waiting for br1 to become free" and I have to hard reset the system. Maybe a sign I've done something dumb?)

    Read the article

  • Two network interfaces and two IP addresses on the same subnet in Linux

    - by Scott Duckworth
    I recently ran into a situation where I needed two IP addresses on the same subnet assigned to one Linux host so that we could run two SSL/TLS sites. My first approach was to use IP aliasing, e.g. using eth0:0, eth0:1, etc, but our network admins have some fairly strict settings in place for security that squashed this idea: They use DHCP snooping and normally don't allow static IP addresses. Static addressing is accomplished by using static DHCP entries, so the same MAC address always gets the same IP assignment. This feature can be disabled per switchport if you ask and you have a reason for it (thankfully I have a good relationship with the network guys and this isn't hard to do). With the DHCP snooping disabled on the switchport, they had to put in a rule on the switch that said MAC address X is allowed to have IP address Y. Unfortunately this had the side effect of also saying that MAC address X is ONLY allowed to have IP address Y. IP aliasing required that MAC address X was assigned two IP addresses, so this didn't work. There may have been a way around these issues on the switch configuration, but in an attempt to preserve good relations with the network admins I tried to find another way. Having two network interfaces seemed like the next logical step. Thankfully this Linux system is a virtual machine, so I was able to easily add a second network interface (without rebooting, I might add - pretty cool). A few keystrokes later I had two network interfaces up and running and both pulled IP addresses from DHCP. But then the problem came in: the network admins could see (on the switch) the ARP entry for both interfaces, but only the first network interface that I brought up would respond to pings or any sort of TCP or UDP traffic. After lots of digging and poking, here's what I came up with. It seems to work, but it also seems to be a lot of work for something that seems like it should be simple. Any alternate ideas out there? Step 1: Enable ARP filtering on all interfaces: # sysctl -w net.ipv4.conf.all.arp_filter=1 # echo "net.ipv4.conf.all.arp_filter = 1" >> /etc/sysctl.conf From the file networking/ip-sysctl.txt in the Linux kernel docs: arp_filter - BOOLEAN 1 - Allows you to have multiple network interfaces on the same subnet, and have the ARPs for each interface be answered based on whether or not the kernel would route a packet from the ARP'd IP out that interface (therefore you must use source based routing for this to work). In other words it allows control of which cards (usually 1) will respond to an arp request. 0 - (default) The kernel can respond to arp requests with addresses from other interfaces. This may seem wrong but it usually makes sense, because it increases the chance of successful communication. IP addresses are owned by the complete host on Linux, not by particular interfaces. Only for more complex setups like load- balancing, does this behaviour cause problems. arp_filter for the interface will be enabled if at least one of conf/{all,interface}/arp_filter is set to TRUE, it will be disabled otherwise Step 2: Implement source-based routing I basically just followed directions from http://lartc.org/howto/lartc.rpdb.multiple-links.html, although that page was written with a different goal in mind (dealing with two ISPs). Assume that the subnet is 10.0.0.0/24, the gateway is 10.0.0.1, the IP address for eth0 is 10.0.0.100, and the IP address for eth1 is 10.0.0.101. Define two new routing tables named eth0 and eth1 in /etc/iproute2/rt_tables: ... top of file omitted ... 1 eth0 2 eth1 Define the routes for these two tables: # ip route add default via 10.0.0.1 table eth0 # ip route add default via 10.0.0.1 table eth1 # ip route add 10.0.0.0/24 dev eth0 src 10.0.0.100 table eth0 # ip route add 10.0.0.0/24 dev eth1 src 10.0.0.101 table eth1 Define the rules for when to use the new routing tables: # ip rule add from 10.0.0.100 table eth0 # ip rule add from 10.0.0.101 table eth1 The main routing table was already taken care of by DHCP (and it's not even clear that its strictly necessary in this case), but it basically equates to this: # ip route add default via 10.0.0.1 dev eth0 # ip route add 130.127.48.0/23 dev eth0 src 10.0.0.100 # ip route add 130.127.48.0/23 dev eth1 src 10.0.0.101 And voila! Everything seems to work just fine. Sending pings to both IP addresses works fine. Sending pings from this system to other systems and forcing the ping to use a specific interface works fine (ping -I eth0 10.0.0.1, ping -I eth1 10.0.0.1). And most importantly, all TCP and UDP traffic to/from either IP address works as expected. So again, my question is: is there a better way to do this? This seems like a lot of work for a seemingly simple problem.

    Read the article

  • NetworkManager Applet shows no networks

    - by Kkelk
    I am "the friend" referred to in the questions here and here. I decided to come and ask a question myself, as I can still not connect to the wireless network. I downloaded Keryx, as suggested here, and managed to download the necessary package and its dependencies. When I attempted to install the packages on Ubuntu using Keryx, Keryx just closed. Following this, I installed the packages manually using dpkg, and as far as I can tell, this was successful: kieran@ubuntu:~$ cd /host/wifi/Keryx/keryx/projects/Kieran/packages kieran@ubuntu:/host/wifi/Keryx/keryx/projects/Kieran/packages$ sudo dpkg -i *.deb [sudo] password for kieran: Selecting previously deselected package bcmwl-kernel-source. (Reading database ... 118296 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.60.48.36+bdcom-0ubuntu5_i386.deb) ... Selecting previously deselected package dkms. Unpacking dkms (from dkms_2.1.1.2-3ubuntu1.1_all.deb) ... Selecting previously deselected package fakeroot. Unpacking fakeroot (from fakeroot_1.14.4-1ubuntu1_i386.deb) ... Selecting previously deselected package linux-image. Unpacking linux-image (from linux-image_2.6.35.22.23_i386.deb) ... Selecting previously deselected package menu. Unpacking menu (from menu_2.1.44ubuntu1_i386.deb) ... Selecting previously deselected package patch. Unpacking patch (from patch_2.6-2ubuntu1_i386.deb) ... Setting up fakeroot (1.14.4-1ubuntu1) ... update-alternatives: using /usr/bin/fakeroot-sysv to provide /usr/bin/fakeroot (fakeroot) in auto mode. Setting up linux-image (2.6.35.22.23) ... Setting up menu (2.1.44ubuntu1) ... Setting up patch (2.6-2ubuntu1) ... Processing triggers for man-db ... Setting up dkms (2.1.1.2-3ubuntu1.1) ... Setting up bcmwl-kernel-source (5.60.48.36+bdcom-0ubuntu5) ... Loading new bcmwl-5.60.48.36+bdcom DKMS files... First Installation: checking all kernels... Building only for 2.6.35-22-generic Building for architecture i686 Building initial module for 2.6.35-22-generic Done. wl.ko: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/2.6.35-22-generic/updates/dkms/ depmod..... DKMS: install Completed. update-initramfs: deferring update (trigger activated) Processing triggers for install-info ... Processing triggers for doc-base ... Processing 31 changed 1 added doc-base file(s)... Registering documents with scrollkeeper... Processing triggers for menu ... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.35-22-generic Warning: No support for locale: en_GB.utf8 After rebooting, however, there were still no wireless networks in the NetworkManager Applet list. I opened the file /var/lib/NetworkManager/NetworkManager.state, and both NetworkEnabled and WirelessEnabled were set to True. While i'm very concious I may be asking a stupid question here, both my friend and I have nothing left to suggest, and as such - I would be very grateful for any answers as to how to get wireless working.

    Read the article

  • W006.15 isp or T-mobile Network Error.

    - by Mike Koerner
    I just bought a new T-Mobile G2.  I wanted to turn on Wifi calling but kept receiving "W006.15 isp or T-mobile Network Error" and asking me to register.  After doing some research I looked at my cable modem/router logs and config.  There were fragmented packets originating from the phone and the incoming fragmented packets were blocked.  I disabled the "Block fragmented packets" setting and the phone was able to connect for Wifi calling

    Read the article

  • Built-in network card not working?

    - by Zeeshan
    Hi, I am new to Ubuntu. I have installed Ubuntu 9.04(Jaunty). After installation I found that network card is not wokring. And id doest not list in "System Preferenes Network Connections" So , i got another card from my friend and try to search on internat about my problem but still cant find solution. Some commands output is here which may be help to solve problem root@mzeeshan-desktop:/home/mzeeshan# uname -r 2.6.28-11-generic root@mzeeshan-desktop:/home/mzeeshan# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:02:44:4a:45:12 inet addr:192.168.5.37 Bcast:192.168.5.255 Mask:255.255.255.0 inet6 addr: fe80::202:44ff:fe4a:4512/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3774 errors:0 dropped:0 overruns:0 frame:0 TX packets:3611 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4307045 (4.3 MB) TX bytes:583067 (583.0 KB) Interrupt:22 Base address:0x1000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) pan0 Link encap:Ethernet HWaddr 5e:25:17:a1:18:ac BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@mzeeshan-desktop:/home/mzeeshan# lspci 00:00.0 Host bridge: Intel Corporation Device 0069 (rev 12) 00:01.0 PCI bridge: Intel Corporation Auburndale/Havendale PCI Express x16 Root Port (rev 12) 00:19.0 Ethernet controller: Intel Corporation Device 10f0 (rev 05) 00:1a.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 1 (rev 05) 00:1c.4 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 5 (rev 05) 00:1c.6 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 7 (rev 05) 00:1c.7 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 8 (rev 05) 00:1d.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Ibex Peak LPC Interface Controller (rev 05) 00:1f.2 IDE interface: Intel Corporation Ibex Peak 4 port SATA IDE Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Ibex Peak SMBus Controller (rev 05) 00:1f.5 IDE interface: Intel Corporation Ibex Peak 2 port SATA IDE Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation GeForce 8400 GS (rev a1) 06:00.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07) 06:00.1 Input device controller: Creative Labs SB Live! Game Port (rev 07) 06:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 06:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) root@mzeeshan-desktop:/home/mzeeshan# Motherboard is Intel DP55WG. I don't know what to do next. Any help will be greatly appreciated.. Thanks

    Read the article

  • Wireless Problem on Acer Aspire 5610z

    - by Ugur Can Yalaki
    I installed ubuntu 12.04 on my machine, but I can't get wireless connection to work. My computer is Acer Aspire 5610z. I found that some other people that have same computer, face the same problem. Here is some information about it: ****** info trace ****** * uname -a * Linux ucy-Aspire-5610Z 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:22:28 UTC 2013 i686 i686 i386 GNU/Linux * lsb_release * Distributor ID: Ubuntu Description: Ubuntu 12.04.3 LTS Release: 12.04 Codename: precise * lspci * 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) Subsystem: AMBIT Microsystem Corp. Device [1468:0422] Kernel driver in use: b43-pci-bridge 06:01.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02) Subsystem: Acer Incorporated [ALI] Device [1025:0090] Kernel driver in use: b44 * lsusb * Bus 001 Device 004: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 5986:0100 Acer, Inc Orbicam Bus 002 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub * PCMCIA Card Info * PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255 * iwconfig * * rfkill * 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no * lsmod * ssb_hcd 12781 0 ssb 51554 2 ssb_hcd,b44 * nm-tool * NetworkManager Tool State: connected (global) Device: usb0 [Wired connection 2] ------------------------------------------- Type: Wired Driver: rndis_host State: connected Default: yes HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: on IPv4 Settings: Address: 192.168.42.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.42.129 DNS: 192.168.42.129 IPv6 Settings: Address: ::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 Address: fe80::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 DNS: fe80::504d:76ff:fe86:db04 Device: eth2 ----------------------------------------------------------------- Type: Wired Driver: b44 State: unavailable Default: no HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: off * NetworkManager.state * [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true * NetworkManager.conf * [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false * interfaces * auto lo iface lo inet loopback * iwlist * * resolv.conf * nameserver 127.0.0.1 * blacklist * [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist-bcm43.conf] blacklist b43 blacklist b43legacy blacklist ssb blacklist bcm43xx blacklist brcm80211 blacklist brcmfmac blacklist brcmsmac blacklist bcma [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac * modinfo * filename: /lib/modules/3.8.0-32-generic/kernel/drivers/usb/host/ssb-hcd.ko license: GPL description: Common USB driver for SSB Bus author: Hauke Mehrtens srcversion: E127A51EDC8F44D2C2A8F15 alias: ssb:v4243id0819rev* alias: ssb:v4243id0817rev* alias: ssb:v4243id0808rev* depends: ssb intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 filename: /lib/modules/3.8.0-32-generic/kernel/drivers/ssb/ssb.ko license: GPL description: Sonics Silicon Backplane driver srcversion: 14621F6EC014F731244437C alias: pci:v000014E4d00004350sv*sd*bc*sc*i* alias: pci:v000014E4d0000432Csv*sd*bc*sc*i* alias: pci:v000014E4d0000432Bsv*sd*bc*sc*i* alias: pci:v000014E4d00004329sv*sd*bc*sc*i* alias: pci:v000014E4d00004328sv*sd*bc*sc*i* alias: pci:v000014E4d00004325sv*sd*bc*sc*i* alias: pci:v000014E4d00004324sv*sd*bc*sc*i* alias: pci:v000014E4d0000A8D6sv*sd*bc*sc*i* alias: pci:v000014E4d00004322sv*sd*bc*sc*i* alias: pci:v000014E4d00004321sv*sd*bc*sc*i* alias: pci:v000014E4d00004320sv*sd*bc*sc*i* alias: pci:v000014E4d00004319sv*sd*bc*sc*i* alias: pci:v000014A4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004315sv*sd*bc*sc*i* alias: pci:v000014E4d00004312sv*sd*bc*sc*i* alias: pci:v000014E4d00004311sv*sd*bc*sc*i* alias: pci:v000014E4d00004307sv*sd*bc*sc*i* alias: pci:v000014E4d00004306sv*sd*bc*sc*i* alias: pci:v000014E4d00004301sv*sd*bc*sc*i* depends: intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 * udev rules * PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb1:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb2:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb3:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2" * dmesg * [ 2.385241] ssb: Found chip with id 0x4311, rev 0x01 and package 0x00 [ 2.385256] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 2.385266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 2.385276] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 2.385286] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 2.448147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 2.468112] ssb: Found chip with id 0x4401, rev 0x02 and package 0x00 [ 2.468124] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 2.468132] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 2.468140] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 2.508230] ssb: Sonics Silicon Backplane found on PCI device 0000:06:01.0 [ 2.528620] b44 ssb1:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver ******** done ******** Thank you already for your help.

    Read the article

  • Transition from web-app development to telecom Integration network (IN) layer development

    - by SIJAR
    How difficult it is for someone who has developed web-application using J2EE, Spring etc technology to develop an application for Telecommunication Integration network (IN) layer, the telecom product is to be developed using SS7 stack, JAIN API, J2EE technology. How vital is the knowledge of telecommunication sector? Does anyone anticipate growth in telecommunication sector, what future lies for web development?

    Read the article

  • network manager applet disappeared after upgrade

    - by Oleksa
    After last upgrade of 12.04 my network manager applet disappeared. When I try to start it from terminal I am getting the message: stasevych@stasevych-laptop:~$ nm-applet ** Message: applet now removed from the notification area nm-applet: symbol lookup error: nm-applet: undefined symbol: nm_secret_agent_get_registered stasevych@stasevych-laptop:~$ While bluetooth applet is well working, as well as nmcli works well from console.

    Read the article

  • Can't access local network when connect to pppoe

    - by shantanu
    I am using DSL(PPPOE) connection in ubuntu. It has two part (I am not sure), when I just connect the cable, system automatically get an IP address started with 172.x.x.x(DHCP). When I connect using username/password (PPPOE) I get another IP started with 10.x.x.x and can access internet but can't access some local IP (in my LAN), which are some FTP, media server provided by my ISP. I complained about that to my ISP but they reply Windows is working It's true, Windows 7 is working fine with this settings. I can access internet and local server at the same time. Also I use a WIFI router (TP-link TL-WR340G/TL-WR340GD) which result the same problem. So when I connect cable directly to system and use Windows 7 than everything is fine. Otherwise problem. Similar problem discussed here. Edit before connect. route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.100.0.1 0.0.0.0 UG 0 0 0 eth0 172.100.0.0 0.0.0.0 255.255.0.0 U 1 0 0 eth0 after connect. Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.12.44.91 0.0.0.0 UG 0 0 0 ppp0 10.12.44.91 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 ifconfig after connect eth0 Link encap:Ethernet HWaddr 74:d0:2b:d5:b3:6c inet6 addr: fe80::76d0:2bff:fed5:b36c/64 Scope:Link inet6 addr: 2002:ac64:154:c:76d0:2bff:fed5:b36c/64 Scope:Global inet6 addr: fec0::c:76d0:2bff:fed5:b36c/64 Scope:Site UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:26582 errors:0 dropped:18 overruns:0 frame:0 TX packets:2340 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2542063 (2.5 MB) TX bytes:244938 (244.9 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4118 errors:0 dropped:0 overruns:0 frame:0 TX packets:4118 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:336759 (336.7 KB) TX bytes:336759 (336.7 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:10.12.44.95 P-t-P:10.12.44.91 Mask:255.255.255.255 inet6 addr: fe80::a536:c7ae:e079:d88d/10 Scope:Link UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:689 errors:0 dropped:0 overruns:0 frame:0 TX packets:744 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:385746 (385.7 KB) TX bytes:75296 (75.2 KB) I used network manager to create network(DSL connection)

    Read the article

  • Ubuntu won't connect to wired network

    - by djeikyb
    I'm running 10.04, upgraded from 9.10, maybe, but probably not upgraded from 9.04. I have two wifi routers. Zeus is connected to the dsl modem. Hermes uses a wds bridge with Zeus to extend the network. My desktop (Daedalus) is ethernetted to Hermes. My laptop (Clyde) is wifi, switching to Hermes or Zeus as needed. Occasionally, as in whenever I transfer a large file from desktop to laptop, the wds bridge will die. Fixing it means restarting both routers, though it seems Hermes should boot first. This is ridiculous, and eventually I'll get around to asking you guys to help me stop it from happening. More importantly is that my desktop requires a reboot to get back on the network. WTF. ifconfig shows my nic has no ip. /etc/init.d/networking restart doesn't do anything, not even give me a lousy ip. dhcpcd eth1 grants me an ip address, but doesn't help with internet access. route -n shows what looks like my normal routing table, but pinging google.com informs me it's an unknown host. jake@daedalus:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 10.1.1.1 0.0.0.0 UG 0 0 0 eth1 It may be worth noting that I can ping both Zeus (10.1.1.1) and Hermes (10.1.1.4) and my laptop (10.1.1.55). Much obliged for any help. Rebooting is, well, trivial in this instance. But it's stupid. I switched to linux because I like the idea that if one part breaks, you fix it instead of reboot reboot reboot. I've left my poor desktop in disarray, confining myself to my little netbook. My desktop is broken, awaiting magical commands from you brilliant folk. (and yes, i know clyde the netbook should be named icarus. it was its original name. ironically the ssd burned out, and i felt it wasn't right when it came to reinstalling)

    Read the article

  • HOWTO: Use Gnome Network Manager in other DE

    <b>Thoughts on Technology:</b> "As of 10.04 beta I have begun using the KDE desktop environment. I really like many of the things KDE has to offer, however KDE's network manager applet (knetworkmanager) still is lacking compared to Gnome's applet."

    Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >