Search Results

Search found 4723 results on 189 pages for 'restart'.

Page 50/189 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

• Unable to ssh to a Linux VM after a day

  - by jogabonito

  I have a machine running 4 VMs on it. There is one Fedora VM which is causing me some trouble. The IPs of the VMs are something like 10.100.100.* I have a Windows PC which is in the same network. It has an IP 10.100.25.77. When I reboot the Fedora VM, I am able to ping it from my Windows PC as well as use putty to ssh to it. The next day, I cant ping it or ssh from my Windows PC. However I can ping and ssh to the other VMs on the machine. If I ssh to one of the other VMs, I can ping and ssh to the Fedora VM. Next if I restart it, things get back to normal and I can access it without any issues. The IP of the VM doesn't change after rebooting and it is statically assigned I would like to know what is causing this and how to get it fixed. As a last resort, I am thinking of running a cron job to restart the VM every night, it is not a critical server, but will be generally used occasionally in the day time.

  Read the article

• Need help toubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

  Read the article

• DRBD as a block device for XEN VM (Centos 5.3)

  - by SaberTooth

  Hi all, I have setup a drbd resource between 2 server nodes - everything works correctly when doing sync tests between the two. (I want to create a HA cluster using drbd,xen and heartbeat) However, when I try and create a XEN VM with Centos as guest operating system, I get through to the partitioning screen on the install but when I select a partitioning type the next screen gives me the following error : "An error has occurred - no valid devices were found on which to create new file systems. Please check your hardware for the cause of this problem." This is the first time attempting create a setup like this and searching Google does not help much... my config files for DRBD and XEN.... DRBD (just the section that is pertinent) on xennode0 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; flexible-meta-disk internal; } on xennode1 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; meta-disk internal; } XEN kernel = "/boot/xeninstall/vmlinuz" ramdisk = "/boot/xeninstall/initrd.img" extra = "text" name = "VM" maxmem = 3000 memory = 3000 vcpus = 4 on_poweroff = "destroy" on_reboot = "restart" on_crash = "restart" vfb = [ ] disk = [ "phy:/dev/drbd0,sda1,w", "tap:aio:/srv/xen/xenswap.img,sda2,w" ] vif = [ "mac=00:16:3e:11:67:ae,bridge=xenbr0" ] root = "/dev/sda1 ro" Thanks in advance!

  Read the article

• Enable bitlocker an save key to share

  - by user273694

  I have searched all over the web but cannot find a complete answer to this: How to enable Bitlocker on a laptop with TPM, and store a file with the Bitlocker recovery key and TPM password by USING THE manage-bde command line tool. The file should be the same as when created in the Bitlocker manager UI. I DO NOT want to save to AD. The same question was asked here but was not answered correctly. The goal is to write a script to be used with an endpoint manager. I have tried the following: manage-bde -on C: Works fine, but does not create or save a key. manage-bde -on C: -rk C:\myfolder\ and manage-bde -on C: -RecoveryKey C:\myfolder\ -rp The output from the last two methods state that a key has been saved to c:\myfolder and so on, but that is not the case. It also says that I have to: Save the password in a secure location Insert a USB flash drive with an external key file into the computer. Restart and run hardware test type "manage-bde -status" to check if the hardware test succeeded After a restart, I get an error saying that Bitlocker could not be enabled because the bitlocker startup key or recovery kpassword cannot be found on the USB device.... C: was not encrypted. Why am I asked to insert a USB?? I simply want to encrypt the hard drive and save the recovery information to a file automatically. Is that too much to ask? Help please!

  Read the article

• Locked out of our Comcast Business Gateway for seemingly no reason

  - by Tyler

  A little backstory... Last fall we migrated our ISP from AT&T to Comcast at one of our offices. At that time, we received a new modem/router from Comcast and we configured everything to our liking. We've never really had very many issues with the router aside from having to restart it every once in a while. Here's the problem... About three months ago I changed the password on the router from the default. After that, I logged into the router several times to make changes with no issue. During May I logged into the router to add two new static routes, no problems. A week ago, I tried to log into the router and could not. I tried the non-default password that I changed it to, the default, anything and everything I could think of and no luck. I restarted the router on Monday thinking it may just be locked up, but after the restart it would still not let me log in. This router is at our other office about 2 hours from here and I want to avoid having to drive down there and reset to factory defaults, reconfigure, etc. Any ideas?

  Read the article

• unicorn and nginx, went wrong

  - by achempion

  I try to deploy my app via capistrano. It was done, but when I start to nginx and show my site in the browser I see 'We're sorry, but something went wrong.' It is bad. I use unicorn. See my configs https://gist.github.com/3904032 I try to start server via rails s -e prodiction and it's work! I think that this error may be because I can't restart server root@li272-194:~# /etc/init.d/nginx restart Restarting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: still could not bind() nginx. any ideas? nginx log 2012/10/17 02:57:41 [error] 3271#0: *1 could not find named location "@myapp", client: 91.192.62.77, server: 178.79.153.194, request: "GET / HTTP/1.1", host: "178.79.153.194" 2012/10/17 02:19:08 [crit] 2448#0: *8 connect() to unix:/srv/zarcon/shared/unicorn.sock failed (2: No such file or directory) while connecting to upstream, client: 91.192.62.77, server: zarkon, request: "GET / HTTP/1.1", upstream: "http://unix:/srv/zarcon/shared/unicorn.sock:/", host: "178.79.153.194"

  Read the article

• ssh hangs on "Last login" line

  - by Pavel H

  This happened for the first time three days ago - I ssh to the server, authenticate using a password, get the welcome message but it remains hanging on the "Last login:..." line. The command line doesn't show and the server doesn't react to my input. Other services on the server keep working ok (apache, tomcat, database, ..). The box has an out-of-band management using which I was able to restart it. After the restart the ssh worked ok again and I didn't find anything suspicious in the logs. Three days later the same problem occurs on this box again, and newly on yet another server in the cluster - 100% same symptoms. Both servers have about 2 month old installation of Debian Squeeze (6.0.2) and the problem never occurred before despite frequent ssh-ing, so it should not be a problem of settings. We haven't been installing anything new for quite some time now. I also made sure there is enough disk space on both servers. Since it started to happen all of a sudden on two servers at about the same time, I suspect some bug may have been introduced via Debian updates, yet I haven't been able to find anyone with the same problem. Most similar issues I have found: ssh freezes at the "Last Login Line" - in our case everything worked fine until recently, so nothing related to settings should be our problem. Diskspace checked, I couldn't check the memory but I would expect something would be in the logs if the system had been running out of it. Remote Fedora system unresponsive, odd but consistent behavior when trying to log in - problem with high load on the server; unlike in this case, nothing changes even if I wait for 10+ minutes

  Read the article

• /etc/hosts: What is loghost? (fresh install of Solaris 10 update 9)

  - by cjavapro

  # # Internet host table # ::1 localhost 127.0.0.1 localhost XX.XX.XX.XX myserver loghost What is the purpose of loghost? If it was not for having loghost in there, all the /etc/hosts files on all the servers in this particular network could be identical. Edit: I looked at /etc/syslog.conf #ident "@(#)syslog.conf 1.5 98/12/14 SMI" /* SunOS 5.0 */ # # Copyright (c) 1991-1998 by Sun Microsystems, Inc. # All rights reserved. # # syslog configuration file. # # This file is processed by m4 so be careful to quote (`') names # that match m4 reserved words. Also, within ifdef's, arguments # containing commas must be quoted. # *.err;kern.notice;auth.notice /dev/sysmsg *.err;kern.debug;daemon.notice;mail.crit /var/adm/messages *.alert;kern.err;daemon.err operator *.alert root *.emerg * # if a non-loghost machine chooses to have authentication messages # sent to the loghost machine, un-comment out the following line: #auth.notice ifdef(`LOGHOST', /var/log/authlog, @loghost) mail.debug ifdef(`LOGHOST', /var/log/syslog, @loghost) # # non-loghost machines will use the following lines to cause "user" # log messages to be logged locally. # ifdef(`LOGHOST', , user.err /dev/sysmsg user.err /var/adm/messages user.alert `root, operator' user.emerg * ) Very interesting. when shutting down,, alerts go to all users probably through *.emerg * Looking at ifdef, it seems that the first parameter checks to see if current machine is a loghost, second parameter is what to do if it is and third parameter is what to do if it is not. Edit: If you want to test a logging rule you can use svcadm restart system-log to restart the logging service and then logger -p notice "test" to send a test log message where notice can be replaced with any type such as user.err, auth.notice, etc.

  Read the article

• My new SSD is causing issues. How can I solve them?

  - by Allan

  Computer specs 1 TB harddisc 120 GB 520intel SSD 8 GB DDR3 RAM Athlon Phenom II x64 955 3. 2ghz DK DFI Lanparty FX7900 M3H3 motherboard ASUS ATI RADEON HD6970 2 GB I have bought a new SSD (Intel 520, 120 GB), and wanted to use this as my system disc. I removed the other harddisc, and installed the SSD with the newest firmware. And then Windows 7 I updated Windows 7 with no problems and then put back my old harddrive. I formatted that old harddrive just to clean up at the same time... So at this stage everything was perfect. My new SSD was set as Master 0 Primary it boots on it and I have 1 TB emptyu harddrive I can use for whatever I want. So far no errors at all Now here is the problem, I installed a few games and everytime I tried to play the computer would say Windows must restart because DCOM server process launcher service terminated, or it says Windows must now restart because the Plug and Play service terminated unexpectedly Most commonly this error is caused by a rootkit virus, well I have tried formatting my entire computer, and running every antivirus I could find, so that shouldn't be it. I've also read somewhere it might happen when there are hardware issues. That on the otherhand would make sense, as I just put in a new SSD. I don't expect you to know this error. I haven't found anyone who knew it yet. maybe you can me guide through what might have gone wrong when I placed in the SSD? What have I checked regarding the SSD? It displays the right name when the computer starts up It has the newest firmware Did a 'sfc /scannow' which told me everything was fine I don't know what to do from here. Everything seems to work great with the drive. when I start playing games my computer crashes.

  Read the article

• Optimizing Apache for large file serving

  - by D_Guy13

  I have a random problem with Apache that I can't quite figure out, here is my setup, Windows Server 2008 R2, 64 Bit, 5GB RAM, SSD with 200 MB(Read/write) and Dual Core CPU @ 2.1 GHz A dump from mod-staus, Server Version: Apache/2.4.7 (Win32) mod_limitipconn/0.24 mod_antiloris/0.5.2 PHP/5.5.9 Server MPM: WinNT Apache Lounge VC11 Server Built: Nov 21 2013 20:13:01 Current Time: Thursday, 21-Aug-2014 23:38:06 W. Europe Daylight Time Restart Time: Thursday, 21-Aug-2014 20:30:47 W. Europe Daylight Time Parent Server Config. Generation: 1 Parent Server MPM Generation: 1 Server uptime: 3 hours 7 minutes 18 seconds Server load: -1.00 -1.00 -1.00 Total accesses: 283025 - Total Traffic: 1172.2 GB 25.2 requests/sec - 106.8 MB/second - 4.2 MB/request 62 requests currently being processed, 388 idle workers Serving large .zip & iso files using mod_xsendfile. (File size range 500 MB - 1.5 GB) The setup works and is running fine. CPU usage is very unstable, jumps all the time between 10% - 90% and the servers goes down when it hits 100%. In that case I have to hard restart the server. Server it outputting traffic at 30 Mbps. Is there anything else I should think about to get a more stable CPU usage? Is that CPU usage normal? Can switching to Linux help me achieve better CPU usage?

  Read the article

• Heavy write to Galera cluster - table locked, cluster practically unusable

  - by Joe

  I set up Galera Cluster on 3 nodes. It works perfectly for reading data. I have done simple application to make some test on the cluster. Unfortunately I have to say that the Cluster fails totally when I try to do some writing. Maybe it can be configured differently or I do sth wrong? I have a simple stored procedure: CREATE PROCEDURE testproc(IN p_idWorker INTEGER) BEGIN DECLARE t_id INT DEFAULT -1; DECLARE t_counter INT ; UPDATE test SET idWorker = p_idWorker WHERE counter = 0 AND idWorker IS NULL limit 1; SELECT id FROM test WHERE idWorker = p_idWorker LIMIT 1 INTO t_id; SELECT ABS(MAX(counter)/MIN(counter)) FROM TEST INTO t_counter; SELECT COUNT(*) FROM test WHERE counter = 0 INTO t_counter; IF t_id >= 0 THEN UPDATE test SET counter = counter + 1 WHERE id = t_id; UPDATE test SET idWorker = NULL WHERE id = t_id; SELECT t_counter AS res; ELSE SELECT 'end' AS res; END IF; END $$ Now my simple C# application creates for example 3 MySQL clients in separate threads and each one executes the procedure every 100ms until there is no record where column 'counter' = 0. Unfortunately - after about 10 seconds sth is going bad. On servers there is process 'query_end' that never ends. After that - you cannot make update on the test table, MySQL returns: ERROR 1205 (HY000): Lock wait timeout exceeded; try restarting transaction . You cant even restart mysql. What you can do is to restart server, sometimes whole cluster. Is Galera Cluster so unreliable when you do massive concucurrent writing/updates? Hard to believe.

  Read the article

• How do i install apache on my ubuntu 12.04 where it has virtualhost

  - by YumYumYum

  According to the docs https://help.ubuntu.com/10.04/serverguide/httpd.html i have done following, and that is almost how i do always in my Fedora, but Ubuntu looks like its not working. a) DNS to IP $ echo "127.0.0.1 a" > /etc/hosts $ echo "127.0.0.1 b" > /etc/hosts b) Apache virtualhost $ ls 1 2 default default.backup default-ssl $ cat 1 <VirtualHost *:80> ServerName a ServerAlias a DocumentRoot /var/www/html/a/public <Directory /var/www/html/a/public> #AddDefaultCharset utf-8 DirectoryIndex index.php AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> $ cat 2 <VirtualHost *:80> ServerName b ServerAlias b DocumentRoot /var/www/html/b/public <Directory /var/www/html/b/public> #AddDefaultCharset utf-8 DirectoryIndex index.php AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> c) load into Apache and restart the service $ a2ensite 1 $ a2ensite 2 $ a2dissite default $ /etc/init.d/apache2 restart d) Browse the new 2 hosts $ firefox http://a Does not work it goes always with http://a or http://b to /var/www/html How do i fix it so that it goes to its own directory e.g: http://a goes to /var/www/html/a/public not /var/www/html?

  Read the article

• Need help ttoubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after rstarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What i have done: I thought it was HDD at first, since this is the only part of the coputer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from bootable USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD apears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoughrouly. The problem still persists, what should my next steps be? Thanks in advance.

  Read the article

• Computer will not boot - disk read error - cannot boot from HD or DVD

  - by Grant Palin

  This is a 3 year-old system: HP a1640n. There have been no issues with it in the past. I added a video card 2 years ago, and more memory 1 year ago, both without issues. There haven't been any recent hardware changes. I did install Win7 in Oct., but there were no issues with that either. I used the computer fine two nights ago, and turned it off. Yesterday, I tried to turn it on, and got the error: "A Disk Read Error Occurred. Press CTRL ALT DEL to restart" So I restart, see the initial start screen (HP) and enter the BIOS. The hard drive and dvd drive appear to be listed, but the names are gibberish text. I tried putting a Windows disk in the dvd drive, and continued with the boot, but the disk did not get recognized. Even though the BIOS was set to check for optical media before the hard drive. Back to the error screen. If the computer would boot from a cd or dvd, I would just figure the hard drive needed replacing. But both being problematic worries me. Is this a matter of replacing both the hard drive and dvd drive, or might it be an indication of a bigger problem? Thanks for any advice.

  Read the article

• Can a non-redundant RAID5 cause any serious problems (compared to RAID0)?

  - by leemes

  I used to have a three-disc RAID5 (mdadm) in my computer for personal media storage (music, videos, photos, programs, games, ...). It had three discs with 750 GB each, resulting in an array capacity of 1.5 TB. One day (one year ago), I needed one of those discs to install another operating system. I thought, I don't need the redundancy anymore since I backup the most important stuff (personal photos e.g.) on an external disc anyway. So I decided to remove one of the three discs without converting the RAID to RAID0 or even two separate discs, because I had no temporary storage (since one cannot simply convert the RAID5 to RAID0 AFAIK). So now, for about one year, I have a non-redundant RAID5 with 2 of 3 discs running. Sometimes, one of the discs has a defective contact at the power cable or something similar causing the drive to stop working temporarily (I don't know exactly what it is). Since it still works when rebooting the computer and in most cases by calling some mdadm commands, it wasn't that problematic. Note that the data is not very critical, since I still have a backup of the most important stuff. But in the last few weeks, one of the drives fails very frequently (every few hours), so it gets really annoying to manage this. My questions are: Is there any disadvantage (apart from the annoying management) of a non-redundant RAID5 (with one drive less than typical) over a RAID0? If I understand it correctly, both have no redundancy and the same capacity. On a temporary drive failure, I can restart the array in both cases, assuming that the drive itself still works after the failure. Can it happen that the drive contents alter on a drive failure, making the array inconsistent? If so, can I tell mdadm to check the array for failures (without a file system level checking tool)? Since the drive most probably only has a defective contact causing it to fail for a second only, can I tell mdadm to automatically restart the array, so I will not even notice the failure if no application wanted to access the file system during the failure?

  Read the article

• MySQL fault linked to windows shutdown failure?

  - by Roy

  As far as i understand my computer is experiencing a strange coincidence (hopefully it isn't and somebody can enlighten me). Basically i shut down my laptop (Windows 7) (at 17.20, today, to be precise) successfully (and so also did XAMPP and its included components). However upon starting my laptop up again in the last hour i noticed that the MySQL module service in my xampp control panel was not coming on (just a big red tick; incidentally everything else was working fine). Now, i had the exact same problem about two weeks ago, whereby i just reinstalled xampp and got it working again. But rather than doing this straight away i thought i would just restart my laptop first. However it won't restart (or shut down first) to be precise now. I can remember Windows wasn't shutting down properly the last time it happened (about two weeks ago). Just wondered if this coincidence pointed to any specific diagnostic as regards the problem with MYSQL? If so i would appreciate greatly any help. Otherwise sorry for wasting your time.

  Read the article

• Configure X connections over TCP without using an X connection

  - by Darren Cook

  I want to run a GUI application on a remote machine I only have ssh access to. I don't need to, or want to, see the GUI window. (I know I could use something like ssh -C -X remote_server if I wanted the GUI to be on my client.) I know X is running on the remote machine, as ps shows this: root ... /usr/bin/Xorg :0 -br -audit 0 -auth /var/gdm/:0.Xauth -nolisten tcp vt7 I set DISPLAY=:0.0 but I then get "Xlib: connection to ":0.0" refused by server" when I try to use it. At Get remote x display working in linux without ssh tunneling and Xserver doesn't work unless DISPLAY=0.0 I see the advice to use gdmsetup to allow X to listen on TCP. But, gdmsetup is a GUI application! And trying to run it over ssh -X did not work ("X11 connection rejected because of wrong authentication"). So, is there a text file I can edit to remove -nolisten? And, after editing it, how do I safely restart X, remotely? (There is other stuff running on this machine, so requesting a reboot is possible, but undesirable.) If not, should gdmsetup be able to run over ssh and I should persevere in that direction? UPDATE: I had to do the ssh -X session as root (ssh as a normal user, then sudo or su, does not work.) So, I did the edit with gdmsetup. I then restarted X with gdm-restart. I've also done xhost + from that ssh -X session. The ps line no longer shows the -nolisten tcp part. But still no luck connecting to it, with either DISPLAY=:0 or DISPLAY=localhost:0

  Read the article

• Timeperiod Setting

  - by Alvin G. Matunog

  I am running Nagios 3.2.3 on CentOS 5.7 32bit and I have a bit of a problem scheduling timeperiods. Please help me. Objective, to stop monitoring during server restart (since the server will be restarted and will be restarted automatically because of updates and system backup). The restart is scheduled every 1st Sunday of every month. My monitoring runs 24x7 but during restarts I want to stop the monitoring and resume after 30 mins. So every 1st Sunday I want my schedule to be 00:00-11:30,12:00-24:00. This means that it will stop at 11:30 and resumes on 12:00nn. If I set this on every Sunday there is no problem. But if I set this time on every 1st Sundays, it stops at 11:30 but resumes on the next day (Monday) and not on 12:00nn Sunday. I don't know what I am missing. If I set on regular weekdays there is no problem. But on Offset weekdays (1st Sunday) it doesn`t work the way it should have. Here is my definition; define timeperiod{ name 1st_sunday timeperiod_name 1st_sunday alias No monitoring every 1st Sunday thursday 1 00:00-11:30,12:00-24:00 } define timeperiod{ timeperiod_name irregular alias regular checking use 1st_sunday sunday 08:30-22:00 monday 08:30-22:00 tuesday 08:30-22:00 wednesday 08:30-22:00 thursday 08:30-19:10,19:20-22:00 friday 08:30-22:00 saturday 08:30-22:00 } Can anyone help me? Please? Thank you.

  Read the article

• PassEnv does not find ENV variables

  - by quodlibetor

  I've got this /etc/profile.d/myfile.sh: export MYVAR=myval I also have a PassEnv MYVAR line in a <virtualhost> section of an apache conf dir. That lets me do things like: $ echo $MYVAR myval $ python >>> import os; os.getenv('MYVAR') 'myval' $ sudo echo $MYVAR myval $ sudo -i root# echo $MYVAR myval But then, despite that being the case I get: root# /sbin/service httpd restart /sbin/service httpd restart Stopping httpd: [ OK ] Starting httpd: [Mon Oct 22 14:44:02 2012] [warn] PassEnv variable MYVAR was undefined [ OK ] And all of my attempts to access MYVAR from within my wsgi scripts just don't work. Thoughts? Am I doing something obviously wrong? EDIT for more detail I've got a swarm of computers/VMs and a swarm of developers working on a swarm of projects. I need a simple central place to keep environment information, the most common is the "environment" (dev/stage/prod). The scheme that we've got (modifying *.wsgi programmatically) is turning out to be more fragile than we'd like. The main options that I see are: put things in the shell environment put things in other config files Getting things into the shell environment is the best, because we won't need to write yet more duplicated "what is my environment" code.

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by user57019

  I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Should I update the kernel on a Linux machine?

  - by Legate

  As I understand it, updating to a new kernel (with the normal linux-image... package, not by rolling my own) requires a server restart. However, one of our servers (Ubuntu 10.04) is running several extensive screen sessions. Restarting kills those which is always a major hassle to their owners (mostly because of lost session histories). What should I do? I see several possibilites: Not doing anything, that is update only non-kernel packages (perhaps use apt-pinning?) Update the kernel, but not restart. (Is that smart? I seem to remember there might be some problems with loading kernel modules.) Updating the kernel and restarting. Is there perhaps some way to preserve the screen sessions? I guess it ultimately boils down to this question: How important is it to update the kernel? I posted this question here instead of askubuntu.com as I think this is not an Ubuntu-specific issue though this server is running Ubuntu.

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by Melot

  Hi! I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Win7 loses connection to network shares after resume unless server specified using FQDN

  - by Szonja Zemkó

  My Win7 client has a connection to a Linux server and its shared folders. The problem occurs when the computer wakes up after a sleep and then one of the shared folders is not accessible. I receive the following message: Error code: 80070035, The network path was not found. I have problem with one specific folder only. When I restart the computer this problematic folder is accessible again. When I log off before sleep the folder is accessible after wakeup. If I try to access the folder by using the FQDN of the server or the server IP it is also accessible. As a temporary solution I mapped the folder to a network drive using the FQDN and it's working fine but it's inconvenient since every other folder is accessible on the server. To summarize: \server\problematicshare no longer works after resume (the Samba server sees my client connect, then disconnects a few seconds later while I receive the above error message) \server\othershare works after resume \fqdn.of.server\problematicshare always works \ip.of.server\problematicshare always works once the problem manifests, I'm no longer able to restart the "Workstation" service (it is not responding) restarting the "Computer Browser" service has no apparent effect the event log doesn't contain anything that seems relevant "ping server" works

  Read the article

• Load Balancing is unusual in Apache in round-robin mode when one of the tomcat is brought down

  - by srayker

  We are facing a unusual behavior with round-robin load balancing on apache when one of the tomcat server is brought down. Our Setup: we have 2 apache web servers on the front end using mod_jk module for load balancing using round robin for load distribution. We also have enabled session stickyness. This is followed by 4 tomcat servers on which the applications are running. Sometimes under heavy load, if there is a slowness in our DB tier we find that eventually one of the tomcat goes into a hung state and would need a restart. The moment we bounce the tomcat we see a spike in requests in one of the server and this would also go into hung state and need a restart. Eventually all the server will face similar condition. What beats me is why does the Apache transfer the whole load to one server instead of distributing the load. We are now trying the worker.balancer.method=B to see if this helps to resolve our issue. Any thoughts on resolving the issue is greatly appreciated. regards, srayker

  Read the article

• Sudo won't execute command as another user

  - by TOdorus

  I'm trying to get a unicorn server to start when the server boots. I've created a shell script which works if I log as the ubuntu user and run /etc/init.d/unicorn start Shell script #!/bin/sh case "$1" in start) cd /home/ubuntu/projects/asbest/current/ unicorn_rails -c /home/ubuntu/projects/asbest/current/config/unicorn.rb -D -E production ;; stop) if ps aux | awk '{print $2 }' | grep `cat ~/projects/asbest/current/tmp/pids/unicorn.pid`> /dev/null; then kill `cat ~/projects/asbest/current/tmp/pids/uni$ ;; restart) $0 stop $0 start ;; esac When I rebooted the server I noticed that the unicorn server wasn't listening to a socket. Since I ran the code succesfully as the ubuntu user I modified the script to let it always use the ubuntu user via sudo. #!/bin/sh case "$1" in start) cd /home/ubuntu/projects/asbest/current/ sudo -u ubuntu unicorn_rails -c /home/ubuntu/projects/asbest/current/config/unicorn.rb -D -E production ;; stop) if ps aux | awk '{print $2 }' | grep `cat ~/projects/asbest/current/tmp/pids/unicorn.pid`> /dev/null; then sudo -u ubuntu kill `cat ~/projects/asbest/current/tmp/pids/uni$ ;; restart) $0 stop $0 start ;; esac After rebooting unicorn still wouldn't start, so I tried running the script from the command line. Now I get the following error sudo: unicorn_rails: command not found I've searched high and low to what could cause this, but I'm afraid I've tapped my limited understanding of Linux. From what I can understand is that although sudo should use the ubuntu user to execute the commands, it still uses the environment of the root user, which isn't configured to run ruby or unicorn. Does anybody have any experience with this?

  Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >