Search Results

Search found 7325 results on 293 pages for 'windows7 32'.

Page 50/293 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

  • How to get a Toshiba L505 to boot USB or CD

    - by ShroudedCloud
    OK, have a Toshiba L505 (not sure of the extended model number) that got a virus on Windows and will no longer will boot into that, so I'm trying to revive it with Ubuntu. Problem is, when I tell it to boot into a USB image of 12.04 32- or 64-bit, 13.04 64-bit, or elementary Luna 32-bit, it gives me some screen with a copyright from 2000 for Intel, invariably spits out a "media not recognized" type of error and then says PXE-ROM exiting. Well, that's annoying. So I went in with a CD (12.04 x86_64 having tried 32-bit in the past as well). Boot menu, select, starts running. Seeing the loading screen for Ubuntu, going well... until it's not. Again, invariably, it fails. The CD drive will cease spinning at around the same time each time and then the laptop will stop doing everything altogether (at least, everything spins down and it goes quiet). As far as I can tell, it's not to do with what function is being loaded from the CD at the time (because that bit is variable). I'd love to be able to boot from USB (since it will be all but required going forward), but getting the CD to work would be wondrous too. Anyone have any ideas of where I can go from here to try to fix this? My friends and I have turned up nothing.

    Read the article

  • wireless card not detected

    - by user281219
    i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

    Read the article

  • How can I replicate the look and limitations of the Super NES?

    - by Mikalichov
    I am looking to produce graphics with the same limitations / look that in the Super Nes era. I am specifically looking for graphics similar to Chrono Trigger / FF6. It would be a lot easier to do if I had an idea of the resolution / dpi I am supposed to use. I found that the technical specs for the SNES are: Progressive: 256 × 224, 512 × 224, 256 × 239, 512 × 239 Interlaced: 512 × 448, 512 × 478 But even by using these resolutions, it is pointless if I set it at 72dpi, as I will still have possibly very detailed graphics (that is the main thing, I don't want detailed graphics, I want to go pixelated). I figured it might be related to the sprite size limit, i.e.: Sprites can be 8 × 8, 16 × 16, 32 × 32, or 64 × 64 pixels, each using one of eight 16-color palettes and tiles from one of two blocks of 256 in VRAM. Up to 32 sprites and 34 8 × 8 sprite tiles may appear on any one line. This would work for sprites (characters, objects), but what about maps? Are they built entirely from 8x8 tiles? And then, at what resolution is the end result displayed? It might seem like I am giving the question and answers at the same time, but all of these are suppositions I am making, so could someone confirm or correct them?

    Read the article

  • Cannot install ia32-lib package

    - by A British Person
    I have several programs that reuquire 32 bit packages (pointing to the ia32-lib package). However, when I try to install it, this happens. spirit@ubuntu:~$ sudo apt-get install ia32-libs Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-multiarch but it is not installable E: Unable to correct problems, you have held broken packages. No big whoop, packages die all the time. I tried a month later however and I still got this error, trying to install the specific package produces this error. spirit@ubuntu:~$ sudo apt-get install ia32-libs-multiarch Reading package lists... Done Building dependency tree Reading state information... Done Package ia32-libs-multiarch is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package 'ia32-libs-multiarch' has no installation candidate I am no Linux whizz-kid, but this seems to be that the package doesn't exist. I searched for Skype in the software centre (I was told this installs the 32-bit packages) and it does not appear in the software centre, and the downloadable from their website produces an error about - funnily enough - no 32-bit packages. Anyone who helps me will get a medal from the gods with the weight of a thousand planets. Just don't wear it for god's sake.

    Read the article

  • Dim (NEARLY blank) laptop screen, secondary screen works - why?

    - by LIttle Ancient Forest Kami
    My laptop screen is (almost) black while my secondary screen is fine. I believe it to be backlight / brightness related. Problem description it starts when I start the laptop system loads and works fine, just screen has problems I can see the screen though very faintly / dimly - it's hard to see anything which ain't very white e.g. starting screen has big Thinkpad logo in white, large font - I can see it, though very dimly second screen works very well Official backligtht debugging: using acpi setting as prescribed there for Thinkpads didn't help I can see an entry in /sys/class/backlight/ and it changes when I press hotkeys for brightness (current backlight power for instance goes up or down) acpi-off didn't helpm neither did acpi_backlight=vendor Hardware data Laptop is Thinkpad Edge with glossy screen. 4 processors, 2 cores, exemplary CPU data from cat /proc/cpuinfo reports Genuine Intel i5 (M 480 @ 2.67GHz). OS is Ubuntu Lucid, 10.04 LTS, 64-bit, with Linux generic kernel (2.6.32-44) and GNOME 2.32.2 (though I doubt there lies the problem). $ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] $ lshw -C display *-display description: VGA compatible controller product: M92 [Mobility Radeon HD 4500 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:33 memory:c0000000-dfffffff(prefetchable) ioport:2000(size=256) memory:f0300000-f030ffff memory:f0320000-f033ffff(prefetchable) Driver I was NOT running any proprietary drivers, just checked with "Hardware drivers". There is one for ATI that is suggested there, though I didn't need it so far. UPDATE: changing the driver to proprietary one (ATI/AMD FGLRX) didn't help. Tried and failed Resetting / running on power or battery / charging / getting rid of static electricity / warming up *doesn't help* This is NOT a blank-screen problem, at least it isn't following official Ubuntu black-screen diagnostics - I can see my screen, though barely. What I will try next: - check last updates I've made - IIRC I am running on nomodeset already, but will verify this Any ideas how to proceed best? What is most probable cause?

    Read the article

  • Driver for asus wireless PC card WL-100GE

    - by emab
    I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

    Read the article

  • How to disguise a serverside mob as another?

    - by Shaun Wild
    I've been working a Minecraft sever mod and i want to be able to add a new entity to the server, but then make the server send the packets to the client, imitating another mob, for example.. Lets say say i have EntityPlayerNPC.class, what i want to do is have all of the packets that get sent to the client look like they are from that of another player which is on the player, therefore allowing me to add custom NPC's... Thinking about the theory i'm sure this can be done. I've tried looking around for where the packets are being sent from and whatnot, can anyone think up a solution? edit: i tried adding a new constructor to the Packet20NamedEntitySpawn class like so: public Packet20NamedEntitySpawn(String username, EntityLiving e){ this.entityId = 0; this.name = username; this.xPosition = MathHelper.floor_double(e.posX * 32.0D); this.yPosition = MathHelper.floor_double(e.posY * 32.0D); this.zPosition = MathHelper.floor_double(e.posZ * 32.0D); this.rotation = (byte)((int)(e.rotationYaw * 256.0F / 360.0F)); this.pitch = (byte)((int)(e.rotationPitch * 256.0F / 360.0F)); this.metadata = e.getDataWatcher(); } unfortunatley, that didn't work :(

    Read the article

  • Fusion Middleware 11gR1 : 6??????

    - by Hiroyuki Yoshino
    2010?6??Fusion Middleware 11gR1 ?????????????? ?????????????3??????? 1. Oracle Enterprise Single Sign-On ?????Microsoft Windows (32-bit), Microsoft Windows x64 ???????????????? 10g?????????????????????????????????????Logon Manager?64-bit???????????? ????·????????????????????????·????????Non Oracle LDAP Certification?????????????? 2. Oracle Tuxedo Oracle Tuxedo 11g???????????? 10g???Oracle Tuxedo System and Application Monitor (TSAM), Oracle Service Architecture Leveraging Tuxedo (SALT)??????????? ??????AIX on Power Systems, HP-UX Itanium, Linux x86, Linux x86-64, Microsoft Windows (32-bit), Microsoft Windows x64, Solaris SPARC (64-bit), Other Platforms ?????????????????????????????????? ????·?????????????????Oracle Tuxedo ? Platform Data Sheets, TSAM ? Supported Platforms, SALT ? Supported Platforms ?????????? 3. Application Adapters ???Mainframe Adapters, CDC Adapters????Application Adapters?11g????????????? JD Edwards, PeopleSoft, SAP, Siebel ??????????????????? ??????AIX on Power Systems, HP-UX Itanium, HP-UX PA-RISC, Linux x86, Linux x86-64, Microsoft Windows (32-bit), Microsoft Windows x64, Solaris SPARC (64-bit) ??????????????? ??????(??????????????????)????????·????????Adapter Certification?????????????? ????? ????????(Media Pack)??????????????(Media Pack)????????????????? (2010?6??????????????????????)

    Read the article

  • Fusion Middleware 11gR1 : 3??????

    - by Hiroyuki Yoshino
    2011?3? (2011/03/08 ??)?Fusion Middleware 11gR1 ?????????????? ?????????????3??????? 1. Oracle iPlanet Web Proxy Server Oracle iPlanet Web Proxy Server???????4.0.14????4.0.15????????? ???????Release Notes (??) ?????????? ?????????????????????? Platforms: AIX, HP-UX Itanium, HP-UX PA-RISC, Linux x86, Linux x86-64, Microsoft Windows (32-bit), Microsoft Windows x64, Solaris (SPARC), Other Platforms 2. Oracle Security Governer Integration Kit ???????????? Oracle Security Governor??Healthcare??????????????????????????????????????????????????????????? ?????????????????????? Platforms: AIX, HP-UX Itanium, HP-UX PA-RISC, Linux x86, Linux x86-64, Microsoft Windows (32-bit), Microsoft Windows x64, Solaris (SPARC) 3. Oracle Tuxedo Oracle Tuxedo????????????????? Oracle Tuxedo System and Application Monitor (TSAM)????(11.1.1.2.0??11.1.1.2.1)????? Oracle Tuxedo JCA Adapter????(11.1.1.2.0??11.1.1.2.1)????? Oracle Service Architecture Leveraging Tuxedo (SALT)????(11.1.1.1.0??11.1.1.2.0)????? ???????????Oracle Tuxedo Application Runtime for CICS and Batch???Oracle Tuxedo Application Rehosting Workbench? ???????????????? CICS????????????????Oracle Tuxedo???????·??????????????·?????????????????COBOL????????????????JCL??????·????????????????????????????????????CICS?????????????????????????????????? ??????????? (??)?????????? ???Oracle Tuxedo?????????????????????????? Platforms: AIX, HP-UX Itanium, Linux x86, Linux x86-64, Microsoft Windows (32-bit), Microsoft Windows x64, Solaris (SPARC), Other Platforms ???????????????

    Read the article

  • Oracle VM Forum????????!?????????????? "??????·????" ??????

    - by rika.tokumichi
    ??????OTN????????? 2010?5?18?????????????????Oracle VM Forum?????????? ?????????????????????????????????? ?????????????????????????????????·?????????????????????????????????????????????????????????????????????????·???????????????????????????????????????????? ??????????4?????????? ????????(?????)???????????·???????~???????????????? 5????~ ?????!????????·????????????????????? ????????????·?????????~???????????????????????~ ????????????????????~????????·????????????????~ ????????????????? ????????????????????????????????OTN?????????????????????????????????????????????????????????Fusion Middleware?????? - Fusion Middleware???????? ????????????????????????????????^^ ???????????????????????????????????? ------------------------------ ?????!????????·????????????????????? ????????????????????????????Xen???????????????? ???Oracle VM for x86?Xen???????????????Xen 4.0????????Oracle VM???????????????????????????????????????Dell PowerEdge R910(CPU 32?????? 64GB)????????? ??????????????????VM????????????????????????????????????????????·???????????????????? ??????????4GB??????·????????????????????·????????????????? ???????VM1???????????????????????VM 30????VM 60?????????????????????? ?????????????????????????????????????VM?????????????????????? ?????????????Self-Ballooning?Transcendent Memory?????????????????????????????????????????????????????????? >Xen??????????????? ????????????????????????Dell PowerEdge R810?????????????????????2U??????????????CPU 32??????????·????32??????????? ----------------------------- ????????????????????~????????·????????????????~ ???????????????????(AP)???????????????????????????????????????????????????????????????????????????????????????????????? ????????????AP????????????????????????? ?????????????????????????????????AP????·????????????????????????????????????????AP·????·????????????????????????????????????? ???????????EC???????????????????????????????????? ????????????????????2?????? ???Oracle Virtual Assembly Builder? ????(Web?AP?DB)????????????????????????????????????????????? ???Oracle WebLogic Server on JRockit Virtual Edition? ????OS?????????????????JVM?????OS????????????????????(?????????????)?????????????????????????? ----------------------------- ??????????????????? >?????????????? ?????????????(??????)?????????????????????????? ?????????????????????????! ?????????????????????????????????????????????????????????

    Read the article

  • Mac 10.6 Universal Binary scipy: cephes/specfun "_aswfa_" symbol not found

    - by Markus
    Hi folks, I can't get scipy to function in 32 bit mode when compiled as a i386/x86_64 universal binary, and executed on my 64 bit 10.6.2 MacPro1,1. My python setup With the help of this answer, I built a 32/64 bit intel universal binary of python 2.6.4 with the intention of using the arch command to select between the architectures. (I managed to make some universal binaries of a few libraries I wanted using lipo.) That all works. I then installed scipy according to the instructions on hyperjeff's article, only with more up-to-date numpy (1.4.0) and skipping the bit about moving numpy aside briefly during the installation of scipy. Now, everything except scipy seems to be working as far as I can tell, and I can indeed select between 32 and 64 bit mode using arch -i386 python and arch -x86_64 python. The error Scipy complains in 32 bit mode: $ arch -x86_64 python -c "import scipy.interpolate; print 'success'" success $ arch -i386 python -c "import scipy.interpolate; print 'success'" Traceback (most recent call last): File "<string>", line 1, in <module> File "/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/interpolate/__init__.py", line 7, in <module> from interpolate import * File "/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/interpolate/interpolate.py", line 13, in <module> import scipy.special as spec File "/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/__init__.py", line 8, in <module> from basic import * File "/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/basic.py", line 8, in <module> from _cephes import * ImportError: dlopen(/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so, 2): Symbol not found: _aswfa_ Referenced from: /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so Expected in: flat namespace in /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so Attempt at tracking down the problem It looks like scipy.interpolate imports something called _cephes, which looks for a symbol called _aswfa_ but can't find it in 32 bit mode. Browsing through scipy's source, I find an ASWFA subroutine in specfun.f. The only scipy product file with a similar name is specfun.so, but both that and _cephes.so appear to be universal binaries: $ cd /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/ $ file _cephes.so specfun.so _cephes.so: Mach-O universal binary with 2 architectures _cephes.so (for architecture i386): Mach-O bundle i386 _cephes.so (for architecture x86_64): Mach-O 64-bit bundle x86_64 specfun.so: Mach-O universal binary with 2 architectures specfun.so (for architecture i386): Mach-O bundle i386 specfun.so (for architecture x86_64): Mach-O 64-bit bundle x86_64 Ho hum. I'm stuck. Things I may try but haven't figured out how yet include compiling specfun.so myself manually, somehow. I would imagine that scipy isn't broken for all 32 bit machines, so I guess something is wrong with the way I've installed it, but I can't figure out what. I don't really expect a full answer given my fairly unique (?) setup, but if anyone has any clues that might point me in the right direction, they'd be greatly appreciated. (edit) More details to address questions: I'm using gfortran (GNU Fortran from GCC 4.2.1 Apple Inc. build 5646). Python 2.6.4 was installed more-or-less like so: cd /tmp curl -O http://www.python.org/ftp/python/2.6.4/Python-2.6.4.tar.bz2 tar xf Python-2.6.4.tar.bz2 cd Python-2.6.4 # Now replace buggy pythonw.c file with one that supports the "arch" command: curl http://bugs.python.org/file14949/pythonw.c | sed s/2.7/2.6/ > Mac/Tools/pythonw.c ./configure --enable-framework=/Library/Frameworks --enable-universalsdk=/ --with-universal-archs=intel make -j4 sudo make frameworkinstall Scipy 0.7.1 was installed pretty much as described as here, but it boils down to a simple sudo python setup.py install. It would indeed appear that the symbol is undefined in the i386 architecture if you look at the _cephes library with nm, as suggested by David Cournapeau: $ nm -arch x86_64 /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so | grep _aswfa_ 00000000000d4950 T _aswfa_ 000000000011e4b0 d _oblate_aswfa_data 000000000011e510 d _oblate_aswfa_nocv_data (snip) $ nm -arch i386 /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so | grep _aswfa_ U _aswfa_ 0002e96c d _oblate_aswfa_data 0002e99c d _oblate_aswfa_nocv_data (snip) however, I can't yet explain its absence.

    Read the article

  • Cocoa QuickLook initiated by NSTableView Cell

    - by Tristan Seifert
    I have an NSTableView that contains 2 different Columns - one is an NSImageCell that shows a file icon, and the second is a custom subclass of NSTextFieldCell that contains a quick look button on the right of the text. When I click the Quick Look button, the following code is invoked: [[QLPreviewPanel sharedPreviewPanel] makeKeyAndOrderFront:nil]; This does it's job and shows the blank Quick Look panel saying "No Items Selected." After I did a bit of research on the internet, I implemented a custom NSTableView subclass to be the Delegate and Data Source for the Quick Look panel. I get the notification that Quick Look asks if I want to be the delegate, and I respond with return YES. Even though I implement all methods in both QLPreviewPanelDataSource and QLPreviewPanelDelegate, at runtime I get this error on the console: 2010-12-24 15:32:17.235 BackMeUp[4763:80f] clicked: ~/Desktop/HUDTape.mov 2010-12-24 15:32:17.489 BackMeUp[4763:80f] [QL] QLError(): -[QLPreviewPanel setDelegate:] called while the panel has no controller - Fix this or this will raise soon. See comments in QLPreviewPanel.h for -acceptsPreviewPanelControl:/-beginPreviewPanelControl:/-endPreviewPanelControl:. 2010-12-24 15:32:17.490 BackMeUp[4763:80f] [QL] QLError(): -[QLPreviewPanel setDataSource:] called while the panel has no controller - Fix this or this will raise soon. See comments in QLPreviewPanel.h for -acceptsPreviewPanelControl:/-beginPreviewPanelControl:/-endPreviewPanelControl:. 2010-12-24 15:32:17.491 BackMeUp[4763:80f] We can now receive QL Events. 2010-12-24 15:32:18.291 BackMeUp[4763:80f] -[NSPathStore2 stringValue]: unrecognized selector sent to instance 0x5ecb10 2010-12-24 15:32:18.292 BackMeUp[4763:80f] -[NSPathStore2 stringValue]: unrecognized selector sent to instance 0x5ecb10 And the Quick Look panel does not show up, which I find rather odd. The first line above is just that I know the cell has been clicked. Anyways, here is the .m file of the custom table view subclass: // // BackupListTableView.m // BackMeUp // // Created by Tristan Seifert on 12/24/10. // Copyright 2010 24/7 Server. All rights reserved. // #import "BackupListTableView.h" @implementation BackupListTableView - (void) awakeFromNib { } // Quick Look Delegates - (BOOL)acceptsPreviewPanelControl:(QLPreviewPanel *)panel; { [QLPreviewPanel sharedPreviewPanel].delegate = self; [QLPreviewPanel sharedPreviewPanel].dataSource = self; NSLog(@"We can now receive QL Events."); return YES; } - (void)beginPreviewPanelControl:(QLPreviewPanel *)panel { // This document is now responsible of the preview panel // It is allowed to set the delegate, data source and refresh panel. [QLPreviewPanel sharedPreviewPanel].delegate = self; [QLPreviewPanel sharedPreviewPanel].dataSource = self; } - (void)endPreviewPanelControl:(QLPreviewPanel *)panel { // This document loses its responsisibility on the preview panel // Until the next call to -beginPreviewPanelControl: it must not // change the panel's delegate, data source or refresh it. return; } // Quick Look panel data source - (NSInteger)numberOfPreviewItemsInPreviewPanel:(QLPreviewPanel *)panel { return 1; } - (id <QLPreviewItem>)previewPanel:(QLPreviewPanel *)panel previewItemAtIndex:(NSInteger)index { int selectedRow = [self selectedRow]; return [NSURL URLWithString:[[[self dataSource] tableView:self objectValueForTableColumn:fileColumn row:selectedRow] stringValue]]; } // Quick Look panel delegate - (BOOL)previewPanel:(QLPreviewPanel *)panel handleEvent:(NSEvent *)event { // redirect all key down events to the table view return NO; } // This delegate method provides the rect on screen from which the panel will zoom. - (NSRect)previewPanel:(QLPreviewPanel *)panel sourceFrameOnScreenForPreviewItem:(id <QLPreviewItem>)item { NSRect iconRect = [self rectOfColumn:1]; /* // check that the icon rect is visible on screen NSRect visibleRect = [self visibleRect]; // convert icon rect to screen coordinates iconRect = [self convertRectToBase:iconRect]; iconRect.origin = [[self window] convertBaseToScreen:iconRect.origin]; */ return iconRect; } // This delegate method provides a transition image between the table view and the preview panel - (id)previewPanel:(QLPreviewPanel *)panel transitionImageForPreviewItem:(id <QLPreviewItem>)item contentRect:(NSRect *)contentRect { int selectedRow = [self selectedRow]; NSImage *fileIcon = [[NSWorkspace sharedWorkspace] iconForFile:[[[self dataSource] tableView:self objectValueForTableColumn:fileColumn row:selectedRow] stringValue]]; return fileIcon; } @end Thanks for any help.

    Read the article

  • [Wireless LAN]hostapd is giving error whwn running in target board

    - by Renjith G
    hi, I got the following error when i tried to run the hostapd command in my target board. Any idea about this? /etc # hostapd -dd hostapd.conf Configuration file: hostapd.conf madwifi_set_iface_flags: dev_up=0 madwifi_set_privacy: enabled=0 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=2 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 2) madwifi_set_privacy: enabled=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=1 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=2 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=3 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid '"RG_WLAN Testing Renjith G"' SSID - hexdump_ascii(len=27): 22 52 47 5f 57 4c 41 4e 20 54 65 73 74 69 6e 67 "RG_WLAN Testing 20 52 65 6e 6a 69 74 68 20 47 22 Renjith G" PSK (ASCII passphrase) - hexdump_ascii(len=12): 6d 79 70 61 73 73 70 68 72 61 73 65 mypassphrase PSK (from passphrase) - hexdump(len=32): 70 6f a6 92 da 9c a8 3b ff 36 85 76 f3 11 9c 5e 5d 4a 4b 79 f4 4e 18 f6 b1 b8 09 af 6c 9c 6c 21 madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x2 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA=0x1 WPA: group state machine entering state GTK_INIT (VLAN-ID 0) GMK - hexdump(len=32): [REMOVED] GTK - hexdump(len=32): [REMOVED] WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 madwifi_set_privacy: enabled=1 madwifi_set_iface_flags: dev_up=1 ath0: Setup of interface done. l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8b1a len=40 Register Fail Register Fail WPA: group state machine entering state SETKEYS (VLAN-ID 0) GMK - hexdump(len=32): [REMOVED] GTK - hexdump(len=32): [REMOVED] wpa_group_setkeys: GKeyDoneStations=0 WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=2 Signal 2 received - terminating Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=2 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 2) madwifi_set_privacy: enabled=0 madwifi_set_ieee8021x: enabled=0 madwifi_set_iface_flags: dev_up=0

    Read the article

  • Performance Optimization for Matrix Rotation

    - by Summer_More_More_Tea
    Hello everyone: I'm now trapped by a performance optimization lab in the book "Computer System from a Programmer's Perspective" described as following: In a N*N matrix M, where N is multiple of 32, the rotate operation can be represented as: Transpose: interchange elements M(i,j) and M(j,i) Exchange rows: Row i is exchanged with row N-1-i A example for matrix rotation(N is 3 instead of 32 for simplicity): ------- ------- |1|2|3| |3|6|9| ------- ------- |4|5|6| after rotate is |2|5|8| ------- ------- |7|8|9| |1|4|7| ------- ------- A naive implementation is: #define RIDX(i,j,n) ((i)*(n)+(j)) void naive_rotate(int dim, pixel *src, pixel *dst) { int i, j; for (i = 0; i < dim; i++) for (j = 0; j < dim; j++) dst[RIDX(dim-1-j, i, dim)] = src[RIDX(i, j, dim)]; } I come up with an idea by inner-loop-unroll. The result is: Code Version Speed Up original 1x unrolled by 2 1.33x unrolled by 4 1.33x unrolled by 8 1.55x unrolled by 16 1.67x unrolled by 32 1.61x I also get a code snippet from pastebin.com that seems can solve this problem: void rotate(int dim, pixel *src, pixel *dst) { int stride = 32; int count = dim >> 5; src += dim - 1; int a1 = count; do { int a2 = dim; do { int a3 = stride; do { *dst++ = *src; src += dim; } while(--a3); src -= dim * stride + 1; dst += dim - stride; } while(--a2); src += dim * (stride + 1); dst -= dim * dim - stride; } while(--a1); } After carefully read the code, I think main idea of this solution is treat 32 rows as a data zone, and perform the rotating operation respectively. Speed up of this version is 1.85x, overwhelming all the loop-unroll version. Here are the questions: In the inner-loop-unroll version, why does increment slow down if the unrolling factor increase, especially change the unrolling factor from 8 to 16, which does not effect the same when switch from 4 to 8? Does the result have some relationship with depth of the CPU pipeline? If the answer is yes, could the degrade of increment reflect pipeline length? What is the probable reason for the optimization of data-zone version? It seems that there is no too much essential difference from the original naive version. EDIT: My test environment is Intel Centrino Duo processor and the verion of gcc is 4.4 Any advice will be highly appreciated! Kind regards!

    Read the article

  • Random strange behaviour on Google Maps v2

    - by fesja
    hi, I'm having a particular fight with Google Maps v2 on Chrome. The map is shown well on all browsers except Chrome, that without any particular reason, it does any of these things as you can see on the image: Moving the center to the south Showing the markers to the right, but if i move the map, they moved too to the next section of the map. Perfect I have the following javascript: if (GBrowserIsCompatible()) { var map = new GMap2(document.getElementById("map")); var bounds = new GLatLngBounds(); map.enableScrollWheelZoom(); map.addControl(new GSmallMapControl()); map.addControl(new GMapTypeControl()); map.removeMapType(G_HYBRID_MAP); var zoomout = 1; var pcenter_0 = new GLatLng(40.420300, -3.705770); var marker_0 = new GMarker(pcenter_0, {draggable: false}); map.addOverlay(marker_0); marker_0.bindInfoWindowHtml('info', {pixelOffset:new GSize(32,5), maxWidth:200} ); bounds.extend(marker_0.getPoint()); var pcenter_1 = new GLatLng(41.385719, 2.170050); var marker_1 = new GMarker(pcenter_1, {draggable: false}); map.addOverlay(marker_1); marker_1.bindInfoWindowHtml('', {pixelOffset:new GSize(32,5), maxWidth:200} ); bounds.extend(marker_1.getPoint()); var pcenter_2 = new GLatLng(48.856918, 2.341210); var marker_2 = new GMarker(pcenter_2, {draggable: false}); map.addOverlay(marker_2); marker_2.bindInfoWindowHtml('info', {pixelOffset:new GSize(32,5), maxWidth:200} ); bounds.extend(marker_2.getPoint()); var pcenter_3 = new GLatLng(37.779160, -122.420052); var marker_3 = new GMarker(pcenter_3, {draggable: false}); map.addOverlay(marker_3); marker_3.bindInfoWindowHtml('', {pixelOffset:new GSize(32,5), maxWidth:200} ); bounds.extend(marker_3.getPoint()); var pcenter_4 = new GLatLng(48.202541, 16.368799); var marker_4 = new GMarker(pcenter_4, {draggable: false}); map.addOverlay(marker_4); marker_4.bindInfoWindowHtml('', {pixelOffset:new GSize(32,5), maxWidth:200} ); bounds.extend(marker_4.getPoint()); zoomToBounds(zoomout); } function zoomToBounds(zoomout) { map.setCenter(bounds.getCenter()); var zoom = map.getBoundsZoomLevel(bounds)-zoomout; if(zoom < 1) zoom = 1; map.setZoom(zoom); map.checkResizeAndCenter(); } Do you have any idea or clue of what can be happening? It's very annoying to have this random javascript errors.. If you need more info, please ask! thanks! Update to add html code (before javascript) <div id="index_map"> <div id="map"></div> </div> I've aldo updated the markers code

    Read the article

  • Hundreds of unknown entries in Linux logwatch

    - by Saif Bechan
    I have a dedicated server which runs centos. Today i got an email from loginwatch on my server with hundreds of lines of 'errors'. I don't really know what they are becasue i am fairly new at this. The lines are in a few sections, I will display the first 10 of all of them, i hope someone can help me fix these problems. --------------------- Named Begin ------------------------ **Unmatched Entries** client 216.146.46.136 notify question section contains no SOA: 8 Time(s) client 92.114.98.10 query (cache) 'adobe.com/A/IN' denied: 4 Time(s) network unreachable resolving '11.254.75.75.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:13c7:7002:3000::11#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:500:13::c7d4:35#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:500:2e::1#53: 2 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:610:240:0:53::193#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:610:240:0:53::3#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:660:3006:1::1:1#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:6b0:7::2#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:dc0:1:0:4777::140#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:dc0:2001:a:4608::59#53: 1 Time(s) network unreachable resolving '146.250.19.67.in-addr.arpa/PTR/IN': 2001:5a0:10::2#53: 1 Time(s) network unreachable resolving '149.207.106.87.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) network unreachable resolving '178.62.24.195.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) this goes on for hundreds of lines with all different domain names. --------------------- pam_unix Begin ------------------------ Failed logins from: 78.86.126.211 (78-86-126-211.zone2.bethere.co.uk): 111 times 93.97.176.136 (93-97-176-136.dsl.cnl.uk.net): 113 times 121.14.145.32: 136 times 190.152.69.5: 248 times 209.160.72.15: 572 times 210.26.48.35: 2 times 212.235.111.224 (DSL212-235-111-224.bb.netvision.net.il): 140 times 218.206.25.29: 140 times Illegal users from: 78.86.126.211 (78-86-126-211.zone2.bethere.co.uk): 2665 times 93.97.176.136 (93-97-176-136.dsl.cnl.uk.net): 2539 times 121.14.145.32: 116 times 190.152.69.5: 34 times 209.160.72.15: 324 times 218.206.25.29: 8051 times proftpd: Unknown Entries: session opened for user cent_ftp by (uid=0): 15 Time(s) session closed for user cent_ftp: 14 Time(s) sshd: Authentication Failures: unknown (218.206.25.29): 8051 Time(s) unknown (78-86-126-211.zone2.bethere.co.uk): 2665 Time(s) unknown (93.97.176.136): 2539 Time(s) root (209.160.72.15): 558 Time(s) unknown (209.160.72.15): 324 Time(s) root (190.152.69.5): 246 Time(s) unknown (121.14.145.32): 116 Time(s) root (121.14.145.32): 106 Time(s) root (dsl212-235-111-224.bb.netvision.net.il): 70 Time(s) root (93.97.176.136): 44 Time(s) root (78-86-126-211.zone2.bethere.co.uk): 37 Time(s) unknown (190.152.69.5): 34 Time(s) mysql (121.14.145.32): 30 Time(s) nobody (218.206.25.29): 26 Time(s) mail (218.206.25.29): 24 Time(s) news (218.206.25.29): 24 Time(s) root (218.206.25.29): 24 Time(s) --------------------- SSHD Begin ------------------------ **Unmatched Entries** pam_succeed_if(sshd:auth): error retrieving information about user tavi : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user pam : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user konchog : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user stavrum : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user rachel : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user affiliates : 24 time(s) pam_succeed_if(sshd:auth): error retrieving information about user nen : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user cobra : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user pass : 7 time(s) pam_succeed_if(sshd:auth): error retrieving information about user hacer : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user chung : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user zainee : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user radu : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user alka : 4 time(s) pam_succeed_if(sshd:auth): error retrieving information about user albert : 5 time(s) pam_succeed_if(sshd:auth): error retrieving information about user turcia : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user cordell : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user silver : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user dragon : 3 time(s) If someone wants to see the whole log i can upload it somewhere. Am i being hacked, what is this all?? I hope someone can help me, this does not look good at all.

    Read the article

  • stunnel crashing

    - by Jay
    I'm trying to use stunnel to secure a legacy application's communications. I can't seem to get it setup and working. Can anyone provide any hints where I'm going wrong? Here's what I'm trying to accomplish: A windows service on a client machine connects to a server on port 7000 using TCP. I'd like to encrypt the communication between client and server. Here's what I've tried: Created a new server that accepts ssl connections on port 7443. Got a certificate for the server and installed it. That seems to work with my test setup. Installed stunnel on my windows machine (version 7.43 from the distribution archive file). Installed libssl32.dll and libeay32.dll in the same directory as stunnel.exe ( from the openssl-0.9.8h-1 binary distribution). Installed it as a service using "stunnel -install" Configured stunnel as follows: debug=7 output=C:\p4\internal\Utility\Proxy\proxy.log service=Proxy taskbar=no [exchange] accept=7000 client=yes connect=proxy.blah.com:7443 I changed my hosts file to trick the old application into connecting through stunnel: server.blah.com 127.0.0.1 # when client looks up server it goes to stunnel proxy.blah.com IP-address-of-server.blah.com # stunnel connects to new server "server.blah.com" now resolves to the machine it's running on (i.e. stunnel). "proxy.blah.com" goes to the real server. stunnel should connect to the server. I start the stunnel service and try to connect. It looks like it's working but the stunnel service just shuts down with no message. 2010.04.19 13:16:21 LOG5[4924:3716]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:16:21 LOG5[4924:3716]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange accepted connection from 127.0.0.1:4134 2010.04.19 13:16:49 LOG6[4924:3748]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange connected remote server from x.253.120.19:4135 2010.04.19 13:20:24 LOG5[3668:3856]: Reading configuration from file stunnel.conf 2010.04.19 13:20:24 LOG7[3668:3856]: Snagged 64 random bytes from C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: Wrote 1024 new random bytes to C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: RAND_status claims sufficient entropy for the PRNG 2010.04.19 13:20:24 LOG7[3668:3856]: PRNG seeded successfully 2010.04.19 13:20:24 LOG7[3668:3856]: SSL context initialized for service exchange 2010.04.19 13:20:24 LOG5[3668:3856]: Configuration successful 2010.04.19 13:20:24 LOG5[3668:3856]: No limit detected for the number of clients 2010.04.19 13:20:24 LOG7[3668:3856]: FD=312 in non-blocking mode 2010.04.19 13:20:24 LOG7[3668:3856]: Option SO_REUSEADDR set on accept socket 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange bound to 0.0.0.0:7000 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange opened FD=312 2010.04.19 13:20:24 LOG5[3668:3856]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:20:24 LOG5[3668:3856]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:21:02 LOG7[3668:4556]: Service exchange accepted FD=372 from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:4556]: Creating a new thread 2010.04.19 13:21:02 LOG7[3668:4556]: New thread created 2010.04.19 13:21:02 LOG7[3668:3756]: Service exchange started 2010.04.19 13:21:02 LOG7[3668:3756]: FD=372 in non-blocking mode 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange accepted connection from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:3756]: FD=396 in non-blocking mode 2010.04.19 13:21:02 LOG6[3668:3756]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:21:02 LOG7[3668:3756]: connect_blocking: s_poll_wait x.80.60.32:7443: waiting 10 seconds 2010.04.19 13:21:02 LOG5[3668:3756]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange connected remote server from x.253.120.19:4157 2010.04.19 13:21:02 LOG7[3668:3756]: Remote FD=396 initialized 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): before/connect initialization 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server certificate A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server done A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client key exchange A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write change cipher spec A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write finished A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 flush data 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read finished A The client thinks the connection is closed: No connection could be made because the target machine actively refused it 127.0.0.1:7000 at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress) at System.Net.Sockets.Socket.Connect(EndPoint remoteEP) at Service.ConnUtility.Connect() Any suggestions?

    Read the article

  • stunnel crashing

    - by Jay
    I'm trying to use stunnel to secure a legacy application's communications. I can't seem to get it setup and working. Can anyone provide any hints where I'm going wrong? Here's what I'm trying to accomplish: A windows service on a client machine connects to a server on port 7000 using TCP. I'd like to encrypt the communication between client and server. Here's what I've tried: Created a new server that accepts ssl connections on port 7443. Got a certificate for the server and installed it. That seems to work with my test setup. Installed stunnel on my windows machine (version 7.43 from the distribution archive file). Installed libssl32.dll and libeay32.dll in the same directory as stunnel.exe ( from the openssl-0.9.8h-1 binary distribution). Installed it as a service using "stunnel -install" Configured stunnel as follows: debug=7 output=C:\p4\internal\Utility\Proxy\proxy.log service=Proxy taskbar=no [exchange] accept=7000 client=yes connect=proxy.blah.com:7443 I changed my hosts file to trick the old application into connecting through stunnel: server.blah.com 127.0.0.1 # when client looks up server it goes to stunnel proxy.blah.com IP-address-of-server.blah.com # stunnel connects to new server "server.blah.com" now resolves to the machine it's running on (i.e. stunnel). "proxy.blah.com" goes to the real server. stunnel should connect to the server. I start the stunnel service and try to connect. It looks like it's working but the stunnel service just shuts down with no message. 2010.04.19 13:16:21 LOG5[4924:3716]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:16:21 LOG5[4924:3716]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange accepted connection from 127.0.0.1:4134 2010.04.19 13:16:49 LOG6[4924:3748]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange connected remote server from x.253.120.19:4135 2010.04.19 13:20:24 LOG5[3668:3856]: Reading configuration from file stunnel.conf 2010.04.19 13:20:24 LOG7[3668:3856]: Snagged 64 random bytes from C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: Wrote 1024 new random bytes to C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: RAND_status claims sufficient entropy for the PRNG 2010.04.19 13:20:24 LOG7[3668:3856]: PRNG seeded successfully 2010.04.19 13:20:24 LOG7[3668:3856]: SSL context initialized for service exchange 2010.04.19 13:20:24 LOG5[3668:3856]: Configuration successful 2010.04.19 13:20:24 LOG5[3668:3856]: No limit detected for the number of clients 2010.04.19 13:20:24 LOG7[3668:3856]: FD=312 in non-blocking mode 2010.04.19 13:20:24 LOG7[3668:3856]: Option SO_REUSEADDR set on accept socket 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange bound to 0.0.0.0:7000 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange opened FD=312 2010.04.19 13:20:24 LOG5[3668:3856]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:20:24 LOG5[3668:3856]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:21:02 LOG7[3668:4556]: Service exchange accepted FD=372 from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:4556]: Creating a new thread 2010.04.19 13:21:02 LOG7[3668:4556]: New thread created 2010.04.19 13:21:02 LOG7[3668:3756]: Service exchange started 2010.04.19 13:21:02 LOG7[3668:3756]: FD=372 in non-blocking mode 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange accepted connection from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:3756]: FD=396 in non-blocking mode 2010.04.19 13:21:02 LOG6[3668:3756]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:21:02 LOG7[3668:3756]: connect_blocking: s_poll_wait x.80.60.32:7443: waiting 10 seconds 2010.04.19 13:21:02 LOG5[3668:3756]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange connected remote server from x.253.120.19:4157 2010.04.19 13:21:02 LOG7[3668:3756]: Remote FD=396 initialized 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): before/connect initialization 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server certificate A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server done A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client key exchange A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write change cipher spec A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write finished A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 flush data 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read finished A The client thinks the connection is closed: No connection could be made because the target machine actively refused it 127.0.0.1:7000 at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress) at System.Net.Sockets.Socket.Connect(EndPoint remoteEP) at Service.ConnUtility.Connect() Any suggestions?

    Read the article

  • Failling install Ralink RT5592 driver on Ubuntu 14.04 LTS

    - by atisou
    My problem concerns the installation of a wi-fi driver (RT5592) for my new wi-fi adapter (PCE-N53) on my newly built computer. Basically, I don't manage to get the driver installed and therefore I cannot get the wifi to work. I know I am not the only one having this issue this year, between RT5592 driver and Ubuntu 14.04 LTS, in one way or the other. Is there anybody who has ever been able to fix this problem? It does not look like on all the posts I have been through... Following an answer to a same problem as mine (I was getting the same error message as Christopher Kyle Horton of "incompatible types" etc), I have applied the instructions and done the editings in a script as suggested by Paul B. Unfortunately I still do get error/warnings message (a different one this time) at the end of the make and the wi-fi still does not work. Below is a snapshot of the end of the message: In file included from /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/include/os/rt_linux.h:31:0, from /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/include/rtmp_os.h:44, from /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/include/rtmp_comm.h:69, from /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/pci_main_dev.c:31: include/linux/module.h:88:32: error: ‘__mod_pci_device_table’ aliased to undefined symbol ‘rt2860_pci_tbl’ extern const struct gtype##_id __mod_##gtype##_table \ ^ include/linux/module.h:146:3: note: in expansion of macro ‘MODULE_GENERIC_TABLE’ MODULE_GENERIC_TABLE(type##_device,name) ^ /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/pci_main_dev.c:73:1: note: in expansion of macro ‘MODULE_DEVICE_TABLE’ MODULE_DEVICE_TABLE(pci, rt2860_pci_tbl); ^ cc1: some warnings being treated as errors make[2]: *** [/home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/pci_main_dev.o] Error 1 make[1]: *** [_module_/home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.13.0-32-generic' make: *** [LINUX] Error 2 The full pastebin data: paste.ubuntu.com/8088834/ It looks from the message that one would need to edit manually some of/other scripts in the driver package, as did Paul B suggest in one case. But I have no idea how to do that. Here is the driver package of the wifi adapter: www.asus.com/uk/Networking/PCEN53/HelpDesk_Download/ My system is as following: OS: ubuntu 14.04 LTS wi-fi card: Asus PCE-N53 motherboard: Asus KCMA-D8 processor: AMD Opteron 4228 HE kernel: 3.13.0-32-generic Following this info from chili555 in here, below are some extra info about my system: lspci -nn | grep 0280 gives 04:00.0 Network controller [0280]: Ralink corp. RT5592 PCI2 Wireless Network Adapater [1814:5592] and sudo apt-get install linux-headers-generic returns linux-headers-generic is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. If this is a kernel version (I have 3.13.0-32-generic) incompatibility issue with the driver as chilli555 suggests (the README file in the driver package says indeed it is compatible with kernel 2.6), how could one trick this around to make it work? that should be possible right? On ubuntu forums, the patches proposed dont work (leads the computer to freeze). Basically: is there anybody out there who has ever been able to make a PCE-N53 work on Ubuntu 14.04 LTS (kernel 3.13)? how shall I edit the driver package to make it work for my kernel?

    Read the article

  • How to set default xrandr settings?

    - by echo-flow
    I'm trying to enable dual monitors in Ubuntu. This is working fine, but every time I do it, desktop effects is disabled. I think I've found the reason why, though: https://wiki.ubuntu.com/X/Config/Multihead/ As with the GNOME XRandR configuration method, setting Virtual to too large a value may result in a loss of hardware acceleration, and thus an inability to use Compiz and its desktop effects. When I use the GNOME monitor applet, or the Monitors configuration in the System menu, the default xrandr settings puts the second monitor to the right of the first, and, as I found with this bug, for most monitors this creates a virtual desktop larger than the maximum 2048 horizontal resolution needed for hardware acceleration on my netbook hardware. So, it seems like if I can modify xrandr's default settings so that it places the new desktop above or below (north or south of) the main LVDS display, then hardware acceleration, and therefore compiz will continue to work. Can anyone tell me, what is the easiest way to achieve this? UPDATE: I have confirmed that multihead support with desktop effects and hardware acceleration works when I move the external monitor display north of the main LVDS display. Right now this involves the following process: plugging in the external monitor, starting the Monitors configuration menu, desktop effects are disabled automatically (and all of the windows on my workspaces are moved to the first workspace), repositioning the external display so that it is north of LVDS display and clicking apply, and then navigating to the Appearance menu and telling it to reenable desktop effects. Is there a simpler way do this? UPDATE 2: OK, so I thought that perhaps the GNOME Monitors configuration screen was trying to be clever, and might be disbling desktop effects. So, I just tried using the xrandr command-line client instead, as follows: xrandr --output VGA1 --above LVDS1 When I do that, desktop effects are still disabled, and I need to manually reenable them. This, despite the fact that hardware acceleration works, and there is never a point where hardware acceleration stops working because the horizontal dimension of the virtual display is too large. So what program is trying to be clever, and is turning off desktop effects when it doesn't need to? And how do I make it stop? If there were a way to re-enable desktop effects from the command line, which I could then put into a script along with the proper xrandr invocation, I would accept that as a workaround. UPDATE 3: OK, here's my script to enable a second monitor with desktop effects. It might be evil, I'm not sure: second-monitor.sh xrandr --output VGA1 --above LVDS1 sleep 3 compiz --replace & The sleep statement might not be necessary. If there's a better way to do this, please let me know. UPDATE 4: This is a Dell Mini Inspiron 1012. Here are my system specifications: lspci -vv 00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: Dell Device 041a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 29 Region 0: Memory at f0b00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at 18d0 [size=8] Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at f0900000 (32-bit, non-prefetchable) [size=1M] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: Dell Device 041a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at f0b80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> lsmod | grep i915 i915 287458 2 drm_kms_helper 29329 1 i915 drm 162409 3 i915,drm_kms_helper intel_agp 24375 2 i915 i2c_algo_bit 5028 1 i915 video 17375 1 i915

    Read the article

  • Why some links appear in a new tab, others in a new window?

    - by SAMIR BHOGAYTA
    Originally, it was made to resolve problems on IE8 32 bits when you use a 32 bits OS. I changed "%ProgramFiles(x86)%" var, and now my issue is resolved for IE8 32 bits on my Windows 7 64 bits. Please try it, and tell me if everything work for you. For Win 7 64 bits : 1 - Create a new notepad document and paste this text : @echo off echo. echo IEREREG Version 1.07 for IE8 27.03.2009 echo by Kai Schaetzl http://iefaq.info echo installs and registers (if suitable) all DLLs known to be used by IE8. echo should only take a few seconds, but please be patient echo. REM ****************************** echo registering IE files REM IE files (= part of setup) regsvr32 /s /i browseui.dll REM regsvr32 /s /i browseui.dll,NI (unnecessary) regsvr32 /s corpol.dll regsvr32 /s dxtmsft.dll regsvr32 /s dxtrans.dll REM simple HTML Mail API regsvr32 /s "%ProgramFiles(x86)%\internet explorer\hmmapi.dll" REM group policy snap-in regsvr32 /s ieaksie.dll REM smart screen regsvr32 /s ieapfltr.dll REM ieak branding regsvr32 /s iedkcs32.dll REM dev tools regsvr32 /s "%ProgramFiles(x86)%\internet explorer\iedvtool.dll" regsvr32 /s iepeers.dll REM Symptom: IE8 closes immediately on launch, missing from IE7 regsvr32 /s "%ProgramFiles(x86)%\internet explorer\ieproxy.dll" REM no install point anymore REM regsvr32 /s /i iesetup.dll REM no reg point anymore REM regsvr32 /s imgutil.dll regsvr32 /s /i /n inetcpl.cpl REM no install point anymore REM regsvr32 /s /i inseng.dll regsvr32 /s jscript.dll REM license manager regsvr32 /s licmgr10.dll REM regsvr32 /s msapsspc.dll REM regsvr32 /s mshta.exe REM VS debugger regsvr32 /s msdbg2.dll REM no install point anymore REM regsvr32 /s /i mshtml.dll regsvr32 /s mshtmled.dll regsvr32 /s msident.dll REM no reg point anymore REM regsvr32 /s msrating.dll REM multimedia timer regsvr32 /s mstime.dll REM no install point anymore REM regsvr32 /s /i occache.dll REM process debug manager regsvr32 /s "%ProgramFiles(x86)%\internet explorer\pdm.dll" REM no reg point anymore REM regsvr32 /s pngfilt.dll REM regsvr32 /s /i setupwbv.dll (not there anymore!) regsvr32 /s tdc.ocx regsvr32 /s /i urlmon.dll REM regsvr32 /s /i urlmon.dll,NI,HKLM regsvr32 /s vbscript.dll REM VML renderer regsvr32 /s "%CommonProgramFiles%\microsoft shared\vgx\vgx.dll" REM no install point anymore REM regsvr32 /s /i webcheck.dll regsvr32 /s /i /n wininet.dll REM ****************************** echo registering system files REM additional system dlls known to be used by IE REM added 11.05.2006 Symptom: Add-Ons-Manager menu entry is present but nothing happens regsvr32 /s extmgr.dll REM added 12.05.2006 Symptom: Javascript links don't work (Robin Walker) .NET hub file regsvr32 /s mscoree.dll REM added 23.03.2009 Symptom: Find on this page is blank regsvr32 /s oleacc.dll REM added 24.03.2009 Symptom: Printing problems, open in new window regsvr32 /s ole32.dll REM mscorier.dll REM mscories.dll REM Symptom: open in new tab/window not working regsvr32 /s actxprxy.dll regsvr32 /s asctrls.ocx regsvr32 /s cdfview.dll regsvr32 /s comcat.dll regsvr32 /s /i /n comctl32.dll regsvr32 /s cryptdlg.dll regsvr32 /s /i /n digest.dll regsvr32 /s dispex.dll regsvr32 /s hlink.dll regsvr32 /s mlang.dll regsvr32 /s mobsync.dll regsvr32 /s /i msieftp.dll REM regsvr32 /s msnsspc.dll #no entry point regsvr32 /s msr2c.dll regsvr32 /s msxml.dll regsvr32 /s oleaut32.dll REM regsvr32 /s plugin.ocx #no entry point regsvr32 /s proctexe.ocx REM plus DllRegisterServerEx ExA ExW ... ? regsvr32 /s /i scrobj.dll REM shdocvw.dll hasn't been updated for IE7 and IE8, it still registers itself for the Windows Internet Controls regsvr32 /s /i shdocvw.dll regsvr32 /s sendmail.dll REM ****************************** REM PKI/crypto functionality REM initpki can take very long to run and is rarely a problem REM if there are problems with crypto, SSL, certificates REM remove the three following REMs from the lines REM echo We are almost done except one crypto file REM echo but this will take very long, be patient! REM regsvr32 /s /i:A initpki.dll REM ****************************** REM tabbed browser, do at the end, why originally with /n ? regsvr32 /s /i ieframe.dll REM ****************************** echo correcting bugs in the registry REM do some corrective work REM Symptom: new tabs page cannot display content because it cannot access the controls (added 27. 3.2009) REM This is a result of a bug in shdocvw.dll (see above), probably only on Windows XP reg add "HKCR\TypeLib\{EAB22AC0-30C1-11CF-A7EB-0000C05BAE0B}\1.1\0\win32" /ve /t REG_SZ /d %systemroot%\system32\ieframe.dll /f REM ****************************** echo all tasks have been finished echo. pause 2 - Close all your IE windows and processes. 3 - Save your document on your Desktop by example, with the .bat extension. Right-click on it, and select "Run as administrator". 4 - Test if this tip resolved your issue by openning IE. If you use a Windows 32 bits version, please replace %ProgramFiles(x86)% by %ProgramFiles% in your .bat file.

    Read the article

  • How to resize / enlarge / grow a non-LVM ext4 partition

    - by Mischa
    I have already searched the forums, but couldnt find a good suitable answer: I have an Ubuntu Server 10.04 as KVM Host and a guest system, that also runs 10.04. The host system uses LVM and there are three logical volumes, which are provided to the guest as virtual block devices - one for /, one for /home and one for swap. The guest had been partitioned without LVM. I have already enlarged the logical volume in the host system - the guest successfully sees the bigger virtual disk. However, this virtual disk contains one "good old" partition, which still has the old small size. The output of fdisk -l is me@produktion:/$ LC_ALL=en_US sudo fdisk -l Disk /dev/vda: 32.2 GB, 32212254720 bytes 255 heads, 63 sectors/track, 3916 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000c8ce7 Device Boot Start End Blocks Id System /dev/vda1 * 1 3917 31455232 83 Linux Disk /dev/vdb: 2147 MB, 2147483648 bytes 244 heads, 47 sectors/track, 365 cylinders Units = cylinders of 11468 * 512 = 5871616 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000f2bf7 Device Boot Start End Blocks Id System /dev/vdb1 1 366 2095104 82 Linux swap / Solaris Partition 1 has different physical/logical beginnings (non-Linux?): phys=(0, 32, 33) logical=(0, 43, 28) Partition 1 has different physical/logical endings: phys=(260, 243, 47) logical=(365, 136, 44) Disk /dev/vdc: 225.5 GB, 225485783040 bytes 255 heads, 63 sectors/track, 27413 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00027f25 Device Boot Start End Blocks Id System /dev/vdc1 1 9138 73398272 83 Linux The output of parted print all is Model: Virtio Block Device (virtblk) Disk /dev/vda: 32.2GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 32.2GB 32.2GB primary ext4 boot Model: Virtio Block Device (virtblk) Disk /dev/vdb: 2147MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 2146MB 2145MB primary linux-swap(v1) Model: Virtio Block Device (virtblk) Disk /dev/vdc: 225GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 75.2GB 75.2GB primary ext4 What I want to achieve is to simply grow or resize the partition /dev/vdc1 so that it uses the whole space provided by the virtual block device /dev/vdc. The problem is, that when I try to do that with parted, it complains: (parted) select /dev/vdc Using /dev/vdc (parted) print Model: Virtio Block Device (virtblk) Disk /dev/vdc: 225GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 75.2GB 75.2GB primary ext4 (parted) resize 1 WARNING: you are attempting to use parted to operate on (resize) a file system. parted's file system manipulation code is not as robust as what you'll find in dedicated, file-system-specific packages like e2fsprogs. We recommend you use parted only to manipulate partition tables, whenever possible. Support for performing most operations on most types of file systems will be removed in an upcoming release. Start? [1049kB]? End? [75.2GB]? 224GB Error: File system has an incompatible feature enabled. Compatible features are has_journal, dir_index, filetype, sparse_super and large_file. Use tune2fs or debugfs to remove features. So what can I do? This is a headless production system. What is a safe way to grow this partition? I CAN unmount it, though - so this is not the problem.

    Read the article

  • ORE graphics using Remote Desktop Protocol

    - by Sherry LaMonica
    Oracle R Enterprise graphics are returned as raster, or bitmap graphics. Raster images consist of tiny squares of color information referred to as pixels that form points of color to create a complete image. Plots that contain raster images render quickly in R and create small, high-quality exported image files in a wide variety of formats. However, it is a known issue that the rendering of raster images can be problematic when creating graphics using a Remote Desktop connection. Raster images do not display in the windows device using Remote Desktop under the default settings. This happens because Remote Desktop restricts the number of colors when connecting to a Windows machine to 16 bits per pixel, and interpolating raster graphics requires many colors, at least 32 bits per pixel.. For example, this simple embedded R image plot will be returned in a raster-based format using a standalone Windows machine:  R> library(ORE) R> ore.connect(user="rquser", sid="orcl", host="localhost", password="rquser", all=TRUE)  R> ore.doEval(function() image(volcano, col=terrain.colors(30))) Here, we first load the ORE packages and connect to the database instance using database login credentials. The ore.doEval function executes the R code within the database embedded R engine and returns the image back to the client R session. Over a Remote Desktop connection under the default settings, this graph will appear blank due to the restricted number of colors. Users who encounter this issue have two options to display ORE graphics over Remote Desktop: either raise Remote Desktop's Color Depth or direct the plot output to an alternate device. Option #1: Raise Remote Desktop Color Depth setting In a Remote Desktop session, all environment variables, including display variables determining Color Depth, are determined by the RCP-Tcp connection settings. For example, users can reduce the Color Depth when connecting over a slow connection. The different settings are 15 bits, 16 bits, 24 bits, or 32 bits per pixel. To raise the Remote Desktop color depth: On the Windows server, launch Remote Desktop Session Host Configuration from the Accessories menu.Under Connections, right click on RDP-Tcp and select Properties.On the Client Settings tab either uncheck LimitMaximum Color Depth or set it to 32 bits per pixel. Click Apply, then OK, log out of the remote session and reconnect.After reconnecting, the Color Depth on the Display tab will be set to 32 bits per pixel.  Raster graphics will now display as expected. For ORE users, the increased color depth results in slightly reduced performance during plot creation, but the graph will be created instead of displaying an empty plot. Option #2: Direct plot output to alternate device Plotting to a non-windows device is a good option if it's not possible to increase Remote Desktop Color Depth, or if performance is degraded when creating the graph. Several device drivers are available for off-screen graphics in R, such as postscript, pdf, and png. On-screen devices include windows, X11 and Cairo. Here we output to the Cairo device to render an on-screen raster graphic.  The grid.raster function in the grid package is analogous to other grid graphical primitives - it draws a raster image within the current plot's grid.  R> options(device = "CairoWin") # use Cairo device for plotting during the session R> library(Cairo) # load Cairo, grid and png libraries  R> library(grid) R> library(png)  R> res <- ore.doEval(function()image(volcano,col=terrain.colors(30))) # create embedded R plot  R> img <- ore.pull(res, graphics = TRUE)$img[[1]] # extract image  R> grid.raster(as.raster(readPNG(img)), interpolate = FALSE) # generate raster graph R> dev.off() # turn off first device   By default, the interpolate argument to grid.raster is TRUE, which means that what is actually drawn by R is a linear interpolation of the pixels in the original image. Setting interpolate to FALSE uses a sample from the pixels in the original image.A list of graphics devices available in R can be found in the Devices help file from the grDevices package: R> help(Devices)

    Read the article

  • Multiple markers in Googe Maps API v3 that link to different pages when clicked

    - by Dave
    I have a map with multiple markers, which I populate via an array. Each marker is clickable and should take the user to a different url per marker. The problem is that all the markers, while displaying the correct title, all use the url of the last entry in the array. Here is my code: var myOptions = { zoom: 9, center: new google.maps.LatLng(40.81940575,-73.95647955), mapTypeId: google.maps.MapTypeId.TERRAIN } var map = new google.maps.Map(document.getElementById("bigmap"), myOptions); setMarkers(map, properties); var properties = [ ['106 Ft Washington Avenue',40.8388485,-73.9436015,'Mjg4'], ['213 Bennett Avenue',40.8574384,-73.9333426,'Mjkz'], ['50 Overlook Terrace',40.8543752,-73.9362542,'Mjky'], ['850 West 176 Street',40.8476012,-73.9417571,'OTM='], ['915 West End Avenue',40.8007478,-73.9692155,'Mjkx']]; function setMarkers(map, buildings) { var image = new google.maps.MarkerImage('map_marker.png', new google.maps.Size(19,32), new google.maps.Point(0,0), new google.maps.Point(10,32)); var shadow = new google.maps.MarkerImage('map_marker_shadow.png', new google.maps.Size(28,32), new google.maps.Point(0,0), new google.maps.Point(10,32)); var bounds = new google.maps.LatLngBounds; for (var i in buildings) { var myLatLng = new google.maps.LatLng(buildings[i][1], buildings[i][2]); bounds.extend(myLatLng); var marker = new google.maps.Marker({ position: myLatLng, map: map, shadow: shadow, icon: image, title: buildings[i][0] }); google.maps.event.addListener(marker, 'click', function() { window.location = ('detail?b=' + buildings[i][3]); }); } map.fitBounds(bounds); } Using this code, clicking any marker take the user to 'detail?b=Mjkx' What am I doing wrong?

    Read the article

  • How can I put multiple markers on Google maps with Javascript API v3?

    - by Doe
    Hi, I'd like to know how to put multiple markers for Google Maps using Javascript API v3. I tried the solution posted here: http://stackoverflow.com/questions/1621991/multiple-markers-in-googe-maps-api-v3-that-link-to-different-pages-when-clicked but it does not work for me for some reason. var directionDisplay; function initialize() { var myOptions = { zoom: 9, center: new google.maps.LatLng(40.81940575,-73.95647955), mapTypeId: google.maps.MapTypeId.TERRAIN } var map = new google.maps.Map(document.getElementById("map_canvas"), myOptions); setMarkers(map, properties); var properties = [ ['106 Ft Washington Avenue',40.8388485,-73.9436015,'Mjg4'], ]; function setMarkers(map, buildings) { var image = new google.maps.MarkerImage('map_marker.png', new google.maps.Size(19,32), new google.maps.Point(0,0), new google.maps.Point(10,32)); var shadow = new google.maps.MarkerImage('map_marker_shadow.png', new google.maps.Size(28,32), new google.maps.Point(0,0), new google.maps.Point(10,32)); var bounds = new google.maps.LatLngBounds; for (var i in buildings) { var myLatLng = new google.maps.LatLng(buildings[i][1], buildings[i][2]); bounds.extend(myLatLng); var marker = new google.maps.Marker({ position: myLatLng, map: map, shadow: shadow, icon: image, title: buildings[i][0] }); google.maps.event.addListener(marker, 'click', function() { window.location = ('detail?b=' + buildings[i][3]); }); } map.fitBounds(bounds); } } </script> Could anyone kindly explain why this doesn't work for me?

    Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >