Search Results

Search found 55281 results on 2212 pages for 'get set'.

Page 509/2212 | < Previous Page | 505 506 507 508 509 510 511 512 513 514 515 516  | Next Page >

• Multi Gateway and Backup Routing on a cisco router

  - by user64880

  Hi all, I have a 2611 Cisco Router with only one Fastethernet port Now I have two internet gateways. I want to config my router as when primary routing fails second routing automatically start to route all my packets. When I set 2 IP route command in my router then I check I see it work well but when peer IP on primary routing is down it can not change to second routing until I remove first route command.In the following I write my setting. How can I set it? interface FastEthernet0/0 ip address 81.12.21.100 255.255.255.248 secondary ip address 62.220.97.14 255.255.255.252 ip route 0.0.0.0 0.0.0.0 62.220.97.13 ip route 0.0.0.0 0.0.0.0 81.12.21.97 100 Cheer, Kamal

  Read the article

• how can I use vim as a wordprocess with soft wordwrap and columns only 40?

  - by Angela

  I have been trying to use vim as a wordprocessor to do most of my initial drafting and then open in abiword or open office to do my final printing. Problem has been, even with :set linebreak and :set wrap, when I open it, there's a ton of line breaks. I have to go and manually remove them. What I want is to be able to write at 40 columns wrap around softly so that when I open it up in Open Office, it gets restored to whatever that column width is, preserving things like carriage return but without all those linebreaks.

  Read the article

• Does Exchange support plussed users (e.g. [email protected]) or a similar mechanism?

  - by Jens Bannmann

  Sendmail supports a feature called 'plussed users'. Once enabled, emails sent to [email protected], [email protected] and [email protected] are automatically delivered just like mails to [email protected]. There is no need to register or set up these 'plus suffixes'. The user can just use them and set up client-side filtering rules on his own. Does Exchange support a similar mechanism? If so, how to enable it? Note that I don't want answers about other means of filtering, e.g. spam/junk filtering, server-side or client-side rules, email aliases/addresses that are configured explicitly and so on.

  Read the article

• Send notification from HTTP bot (RESTful service or whatever)

  - by Kuroki Kaze

  I have very simple bot that gathers and parses web pages. It's on a machine in network, behind NAT (so I cannot setup a web server, for example). I don't have MTA set up. The bot should notify me about changes in parsed pages (once in a hour or two, to one recipient). How can this be done? Is there any RESTful email gateways, like SMS ones? I can set up him a twitter account and use curl to post statuses/DM, but it's a very temporary bot.

  Read the article

• NIS server setting problem in ubuntu

  - by Asma

  Hi, I set NFS for server-client that works properly. Now I am trying to set NIS server-client on same PC's. I am following the instruction from "SettingUpNISHowTo" from https://help.ubuntu.com/community/SettingUpNISHowTo link. But in step-10, "sudo /etc/init.d/nis restart".......it show error fail. If I try to use "ypcat passwd" to check......it shows error YPBINDPROC_DOMAIN: Domain not bound No such map passwd.byname. Reason: Can't bind to server which serves this domain Can anyone able to help me to get rid out from this problem? Is all the step in the document is proper to configure the NIS server? Thanks in advance.

  Read the article

• How can I bulk rename files in a RAR or ZIP archive on the mac?

  - by Chris R

  I have a set of archive files -- both zip and rar formats -- inside of which I need to rename some files. Specifically, I want to do something like this: for each archive file in a directory for each file in the archive if the file name matches the regular expression /(.* - [0-9]{2})([0-9]{2} - .)*/ rename the file as \1-\2 The trick isn't so much in the generation of the new name; I can do that with either bash or sed or anything else. It's the set of commands to manipulate the files in the archives using rar/unrar or unzip/zip (If it makes a difference, I'm re-formatting some CBR/CBZ files to get the double-page spreads to come up in the right order in SimpleComic -- it interprets page 0203 as page 203, which makes the story a bit hard to follow)

  Read the article

• Word Macro: Move Cursor Down a Row

  - by Bryan

  I have a macro which I've been using to merge two cells together in a word table, but what I want to do is to get the cursor to move down by one cell, so that I can repeatedly press the shortcut key to repeat the command over and over. The macro code that I have (shamelessy copied and pasted from a web page), is as follows: Sub MergeWithCellToRight() ' ' MergeWithCellToRight Macro ' ' Dim oRng As Range Dim oCell As Cell Set oCell = Selection.Cells(1) If oCell.ColumnIndex = Selection.Rows(1).Cells.Count Then MsgBox "There is no cell to the right?", vbCritical, "Error" Exit Sub End If Set oRng = oCell.Range oRng.MoveEnd wdCell, 1 oRng.Cells.Merge Selection.Collapse wdCollapseStart End Sub I've attempted to add the following line just before the 'End Sub' statement Selection.MoveDown wdCell, 1 but this generates the error, Run-time error '4120' Bad Parameter whenever I execute the macro. Can anyone tell me how to correct this or what I'm doing wrong?

  Read the article

• Windows Server 2008 R2 permissions: Users can't write despite being administrators

  - by Matias Nino

  We just set up a new R2 server and created a bunch of local user accounts on it that are part of the administrator's group. We then set permissions on some shares and folders to allow FULL CONTROL to anyone from the administrator's group. However, the users cannot write to these folders when logged on. On some folders on the C:\ they are prompted for consent in order to gain permission to read them. Any ideas? Are there any tools that would help me troubleshoot this? Thanks in advance for any tips.

  Read the article

• Event ID 17890 (A significant part... paged out.) with SQL Server 2008

  - by Godeke

  I have a machine that has SQL Server 2008 Standard installed. Periodically (about once an hour) I am getting Event ID 17890 several times in a row. An example: 6:28:54 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 0 seconds. Working set (KB): 10652, committed (KB): 628428, memory utilization: 1%%. 6:34:27 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 332 seconds. Working set (KB): 169780, committed (KB): 546124, memory utilization: 31%%." 6:38:55 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 600 seconds. Working set (KB): 245068, committed (KB): 546124, memory utilization: 44%%." This pattern repeated at 7:26 - 7:37, 8:26 - 8:36, 9:24 - 9:35 and so with the same increasing working set and memory utilization pattern. I don't have any (known) background tasks running at this time. Backups run at 2:00 This subsided from 11:00 at night until it resumed at 4:00 in the morning and has been continuing the intermittent 10 minute glitch periods. As this server has plenty of RAM (the commit charge has peaked at 2,871,564 of 4,194,012 physical) I disabled the paging files after reading several items I dug up searching Google and not finding any of them changing the situation. This pattern I am documented is after removing the paging files, so I'm not even sure where we are paging the SQL process could be going. I also changed the SQL process memory to have a minimum of 500MB and a maximum of 2GB of RAM (as this is a light duty database server serving only a small workgroup). Has anyone encountered this? Prior to disabling the page files this error would cause 5 minutes of disk thrashing that disabled access to the databases, files, IIS webs and so on. Since disabling the page files it just logs strange things, but I'm not seeing a performance drop at least. Any suggestions would be welcome.

  Read the article

• Get tortoisesvn to give me filenames with build number in the filename

  - by EricJLN

  I am on a Windows 7 box, and I have tortoisesvn on my machine. After getting a little familiar with svn and tortoisesvn on a code repository, I set up a local repository to manage revisions of some word and powerpoint documents. I want to figure out some scripted way to output a set of files with the build/revision number embedded in the filename. I will then email the files to some business people to review. For example, say I have a group of files in my working directory: PresentA.pptx PresentA-notes.docx PresentB.pptx and TortoiseSVN repo browser tells me that I am currently at revision 21 for PresentA.pptx and PresentA-notes.docx but at revision 25 for PresentB.pptx, I would like some way to get 3 files with the following names: PresentA-r21.pptx PresentA-notes-r21.docx PresentB-r25.pptx Alternatively, if revision 25 is the current value for the repository, having all the names appended with -r25 would work, too.

  Read the article

• Where can I find logs for SFTP?

  - by Jake

  I'm trying to set up sftp-server but the client is getting an error, Connection closed by server with exitcode 1 /var/log/auth.log (below) doesn't help much, how can I find out what the error is? I'm running Ubuntu 10.04.1 LTS sshd[27236]: Accepted password for theuser from (my ip) port 13547 ssh2 sshd[27236]: pam_unix(sshd:session): session opened for user theuser by (uid=0) sshd[27300]: subsystem request for sftp sshd[27236]: pam_unix(sshd:session): session closed for user theuser Update: I've been prodding this for a while now, I've got the sftp command on another server giving me a more useful error. Request for subsystem 'sftp' failed on channel 0 Couldn't read packet: Connection reset by peer Everything I've found on the net suggests this id a problem with sftp-server but when I remove the chroot from sshd config I can access the system. I assume this means sftp-server is accessible and set up correctly.

  Read the article

• need help upgrading small business wifi network

  - by Henry Jackson

  Our small business currently has 3 wireless access points around the building, each with their own SSID. Security is done with WEP (ick) and MAC address filtering (double ick). We are trying to reconfigure the setup, with these goals: wifi roaming between the access points user-based authentication that isn't as annoying as MAC address filtering. 1) The entire building is hardwired with ethernet, so I assume it should be easy to set up the routers to act as one big network, but I can't figure out how. Can someone point me in the right direction? The routers are consumer-grade linksys routers, is it possible to do this without getting new hardware? 2) For security, we will probably upgrade to WPA2, and I'm thinking of using the Enterprise version so that users can log in with a username, instead of having a single key (so if an employee leaves or something, their access can be removed). We have several on-site Windows servers, can one of them be set up as a RADIUS server, or is that best left to a dedicated machine (again, using existing hardware is good).

  Read the article

• need help upgrading small business wifi network

  - by Henry Jackson

  Our small business currently has 3 wireless access points around the building, each with their own SSID. Security is done with WEP (ick) and MAC address filtering (double ick). We are trying to reconfigure the setup, with these goals: wifi roaming between the access points user-based authentication that isn't as annoying as MAC address filtering. 1) The entire building is hardwired with ethernet, so I assume it should be easy to set up the routers to act as one big network, but I can't figure out how. Can someone point me in the right direction? The routers are consumer-grade linksys routers, is it possible to do this without getting new hardware? 2) For security, we will probably upgrade to WPA2, and I'm thinking of using the Enterprise version so that users can log in with a username, instead of having a single key (so if an employee leaves or something, their access can be removed). We have several on-site Windows servers, can one of them be set up as a RADIUS server, or is that best left to a dedicated machine (again, using existing hardware is good).

  Read the article

• need help upgrading small business wifi network

  - by Henry Jackson

  Our small business currently has 3 wireless access points around the building, each with their own SSID. Security is done with WEP (ick) and MAC address filtering (double ick). We are trying to reconfigure the setup, with these goals: wifi roaming between the access points user-based authentication that isn't as annoying as MAC address filtering. 1) The entire building is hardwired with ethernet, so I assume it should be easy to set up the routers to act as one big network, but I can't figure out how. Can someone point me in the right direction? The routers are consumer-grade linksys routers, is it possible to do this without getting new hardware? 2) For security, we will probably upgrade to WPA2, and I'm thinking of using the Enterprise version so that users can log in with a username, instead of having a single key (so if an employee leaves or something, their access can be removed). We have several on-site Windows servers, can one of them be set up as a RADIUS server, or is that best left to a dedicated machine (again, using existing hardware is good).

  Read the article

• Configuring Ubuntu 10.04's Greeter Screen

  - by Skizz

  I have an Ubuntu server (9.04 at the moment) and an Ubuntu desktop which I recently upgraded to 10.04. Once I'd set up the users and groups on the desktop to match the server (I'm new to this, I think LDAP would do this for me, but that's another question), the friendly greeter screen no longer displays the same set of users1. In 9.04 (the previous version running on the desktop PC) there were four users shown. These had UIDs of 500 to 510. Changing the UIDs is one solution, but that would mean changing the UIDs on all my linux PCs, and that is a might PITA (unless there's a tool to make it less painful). How can I get the greeter in 10.04 to show users with UIDs in the 500s without resorting to changing the UIDs? I use the greeter screen with user pictures as the PC is mainly for use by my young children and clicking the picture is a bit easier (they still need to type a password though).

  Read the article

• Browser-based Operating System

  - by Ross Peoples

  I have a bunch of touchscreen machines that I want to display a webpage on and have users interact with the webpage via the touchscreen. Right now, this is done with a full-blown OS with a browser set to run at startup. I think maybe the ideal solution is to use a Linux-based OS that boots up, starts X, then starts a web browser (Chrome, Firefox, or whatever) in full screen mode. What kind of options do I have? I really want to avoid using a full-blown OS like I do now. It looks unprofessional and takes a while to boot up. I was thinking maybe Chrome OS or something, but I wouldn't know how to set it up for my purposes, since it's still designed to be used as a desktop OS instead of a kiosk-type OS.

  Read the article

• How to change theme in Windows 7 with Powershell script?

  - by Greg McGuffey

  I would like to have a script that would change the current theme of Windows 7. I found the registry entry where this stored, but I apparently need to take some further action to get windows to load the theme. Any ideas? Here is the script that I'm trying to use, but isn't working (registry updated, but theme not changed): ###################################### # Change theme by updating registry. # ###################################### # Define argument which defines which theme to apply. param ( [string] $theme = $(Read-Host -prompt "Theme") ) # Define the themes we know about. $knownThemes = @{ "myTheme" = "mytheme.theme"; "alien" = "oem.theme" } # Identify paths to user themes. $userThemes = " C:\Users\yoda\AppData\Local\Microsoft\Windows\" # Get name of theme file, based on theme provided $themeFile = $knownThemes["$theme"] # Build path to theme and set registry. $newThemePath = "$userThemes$themeFile" $regPath = "HKCU:\Software\Microsoft\Windows\CurrentVersion\Themes\" Set-ItemProperty -path $regPath -name CurrentTheme -value $newThemePath # Update system with this info...this isn't working! rundll32.exe user32.dll, UpdatePerUserSystemParameters Thanks!

  Read the article

• On Windows 7, how can I make the Start Menu search feature include matches from within words, not just the start of the word?

  - by Gabriel

  I have a program installed called WinSCP. When I press the Windows key and type "SCP", I get "No items match your search." Is there a configuration option I can set somewhere, so that this item will be found? I'm not looking for a specific solution for this particular program, but something general, so that if there's a program named XYZ, I can find it via the Start Menu search by entering YZ. EDIT TO ADD: I'm looking for a "set-it and forget-it" type of configuration change, so that within-word searching happens always, automatically. I don't want to have to type a * before every query. Apparently this wasn't clear from what I wrote above.

  Read the article

• Reg Expression htaccess RewriteRule

  - by Rick

  I am new to using regular expressions for rewriting URL's in htaccess I need to redirect mysite.com/123 to mysite.com/, IF cookie named 'ref' is set. my current htaccess is: <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{HTTP_COOKIE} ref=true [NC] RewriteRule ^/([0-9]+)/$ http://www.mysite.com </IfModule> The goal is that when someone enters site with: mysite.com/111(some number) that they are redirected to the home page of the site after the cookie is set. Be nice... I'm new! ;o)

  Read the article

• Wget site mirror, links with rel="<content>" not followed

  - by Pacifika

  Whilst creating a site mirror using wget 1.12 on Ubuntu links with a rel attribute set are not downloaded: <a href="link" rel="tag">text</a> Rel="tag" is a microformat (By adding rel="tag" to a hyperlink, a page indicates that the destination of that hyperlink is an author-designated "tag" (or keyword/subject) for the current page). My WordPress theme uses this for link to tags, so 99% of the site is ignored. Edit: it turns out all my permalinks use rel="bookmark" and are skipped as well. I'm using the following wget command (this ignores robots.txt and also follows nofollow links): wget -mkp -e robots=off http://site How do I make wget follow links with rel set?

  Read the article

• Setting DNS Siffix for multiple network adapters in a VM

  - by arun_bh

  Is there a way to set the DNS Suffix for multiple network adapters in a VM using the sysprep file? We are trying to setup Windows 2003 VMs with 2 network adapters. In the one adapter case the sysprep we are able to set the suffix using DNSDomain. But this doesnt work in the 2 adapter case. The The VM is setup corrently though without any issues but one of our apps relies on the DNS Suffix value to work correctly. Thanks in advance.

  Read the article

• Setting up Tornado with Nginx on Ubuntu 10.04 for production use

  - by DjangoRocks

  Hi all, I understand that there's an nginx configuration file at http://www.friendfeed.com But i don't really know how to set up Tornada for production use on Ubuntu 10.04 with Nginx. Here's my situation and assumptions: 1) Assuming my Tornado project is set up as such: project/ src/ static/ templates/ project.py And I have installed Tornado by downloading the repositary from Github and than sudo python setup.py install 2) I've installed Nginx and started it based on the instructions here : http://library.linode.com/web-servers/nginx/installation/ubuntu-10.04-lucid My questions are: Where does my nginx configuration file go ? Within the src/ folder? After configuring Nginx, how do I start my Tornado project?

  Read the article

• Requesting better explanation for etag/expiration of favicon.ico

  - by syn4k

  Following this article: Configuring favicon with expires header in htaccess Using YSlow, I keep getting: (no expires) http://devwww.someplace.com/favicon.ico Also, YSlow indicates: Grade C on Configure entity tags (ETags) for the same file. My relevant config (.htaccess): # Configure ETags FileETag MTime Size <IfModule mod_expires.c> # Enable Expires Headers for this directory and sub directories that don't override it ExpiresActive on # Set default expiration for all files ExpiresDefault "access plus 24 hours" # Add Proper MIME-Type for Favicon AddType image/x-icon .ico # Set specific expriation by file type ExpiresByType image/x-icon "access plus 1 month" ExpiresByType image/ico "access plus 1 month" ExpiresByType image/icon "access plus 1 month" </IfModule> As you can see, I am setting both, etags and expiration however, both seem to be ignored. Yes, mod_expires is being loaded by my Apache configuration.

  Read the article

• How to change the audio output device in Firefox or any other modern browser?

  - by Zanami Zani

  I'm trying to play music through Ventrilo and currently I use Virtual Audio Cable. The way it works is that in foobar2000 (a music playing program) I set the output device in preferences to Virtual Audio Cable. Then in Ventrilo I log in to another name and set the input device to Virtual Audio Cable. This routes the music through the Virtual Audio Cable and allows me to play the music through Ventrilo. However, I would also like to change the output device for Firefox (or any other browser) or "Plugin Container for Firefix" to Virtual Audio Cable so that I could play music from Pandora or YouTube on to Ventrilo. Unfortunately I could not find an option for this anywhere.

  Read the article

• Hosting several domains on one server using IIS 7

  - by Øyvind Knobloch-Bråthen

  I have created several web sites inside IIS7 on my server. All of them use the same ip and port, but different host names. Currently I have set the host name to www.mydomain.com. Now my question is, how do I get my actual domains to target the different sites on my server. Second question. Can I set my host name to only mydomain.com to make sure that all requests to that domain is handeled by the same application? Primarily, I want both www.mydomain.com and mydomain.com to work when the user types the address in their browser.

  Read the article

< Previous Page | 505 506 507 508 509 510 511 512 513 514 515 516  | Next Page >