Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 51/172 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

  • DNS Problems (NIGHTMARES!) with BIND and Virtualmin

    - by Nyxynyx
    I have a webserver (Ubuntu 12.04 with LAMP) using Virtualmin / Webmin. Because I just moved from a Cpanel system, I am having a nightmare configuring the DNS! Using intoDNS.com, the failed reports are: Mismatched NS records WARNING: One or more of your nameservers did not return any of your NS records. DNS servers responded ERROR: One or more of your nameservers did not respond: The ones that did not respond are: 123.123.123.123 213.251.188.141x Multiple Nameservers ERROR: Looks like you have less than 2 nameservers. According to RFC2182 section 5 you must have at least 3 nameservers, and no more than 7. Having 2 nameservers is also ok by me. Missing nameservers reported by your nameserver You should already know that your NS records at your nameservers are missing, so here it is again: ns1.mydomain.com. sdns2.ovh.net. SOA record No valid SOA record came back! MX Records WWW A Record ERROR: I could not get any A records for www.mydomain.com! Step-by-Step of my Attempt In my domain registrar (Namecheap), I registered ns1.mydomain.com as a nameserver, pointing to the IP address of my web server which is running bind9. The domain is setup with DNS ns1.mydomain.com and sdns2.ovh.net. sdns2.ovh.net is a secondary DNS server (SLAVE and pointing mydomain.com to the IP address of my web server) Webserver domain: mydomain.com Webserver hostname: ns4000000.ip-123-123-123.net Webserver IP: 123.123.123.123 Under Virtualmin, I edited the default Virtual server template, BIND DNS records for new domains: ns1.mydomain.com Master DNS server hostname: ns1.mydomain.com Next I created a Virtual server using that server template. This is what I've done but its still not working! Any ideas? I've been stuck for days, thank you for all your help! service bind9 status * bind9 is running lsof -i :53 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME named 6966 bind 20u IPv6 338583 0t0 TCP *:domain (LISTEN) named 6966 bind 21u IPv4 338588 0t0 TCP localhost.localdomain:domain (LISTEN) named 6966 bind 22u IPv4 338590 0t0 TCP ns4000000.ip-123-123-123.net:domain (LISTEN) named 6966 bind 512u IPv6 338582 0t0 UDP *:domain named 6966 bind 513u IPv4 338587 0t0 UDP localhost.localdomain:domain named 6966 bind 514u IPv4 338589 0t0 UDP ns4000000.ip-123-123-123.net:domain /etc/resolv.con (Not sure how 213.186.33.99 got here) nameserver 127.0.0.1 nameserver 213.186.33.99 search ovh.net host 123.123.123.123 (my web server's IP) 13.60.245.198.in-addr.arpa domain name pointer ns4000000.ip-123-123-123.net. nslookup 213.186.33.99 Server: 127.0.0.1 Address: 127.0.0.1#53 Non-authoritative answer: 99.33.186.213.in-addr.arpa name = cdns.ovh.net. Authoritative answers can be found from: 33.186.213.in-addr.arpa nameserver = ns.ovh.net. 33.186.213.in-addr.arpa nameserver = dns.ovh.net. nslookup ns1.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached nslookup ns2.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached nslookup www.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached dig mydomain.com ; <<>> DiG 9.8.1-P1 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 43540 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;mydomain.com. IN A ;; Query time: 0 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Thu Oct 11 11:30:09 2012 ;; MSG SIZE rcvd: 30 dig ns1.mydomain.com ; <<>> DiG 9.8.1-P1 <<>> ns1.mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 31254 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;ns1.mydomain.com. IN A ;; Query time: 0 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Thu Oct 11 11:30:16 2012 ;; MSG SIZE rcvd: 34 /etc/bind/named.conf include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; /etc/bind/named.conf.default-zones zone "." { type hint; file "/etc/bind/db.root"; }; zone "localhost" { type master; file "/etc/bind/db.local"; }; zone "127.in-addr.arpa" { type master; file "/etc/bind/db.127"; }; zone "0.in-addr.arpa" { type master; file "/etc/bind/db.0"; }; zone "255.in-addr.arpa" { type master; file "/etc/bind/db.255"; }; /etc/bind/named.conf.local zone "mydomain.com" { type master; file "/var/lib/bind/mydomain.com.hosts"; allow-transfer { 127.0.0.1; localnets; }; }; /etc/bind/named.conf.options options { directory "/var/cache/bind"; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; // allow-recursion { 127.0.0.1; }; // transfer-source; }; named-checkconf -z dns_master_load: /var/lib/bind/mydomain.com.hosts:21: unexpected end of line dns_master_load: /var/lib/bind/mydomain.com.hosts:20: unexpected end of input /var/lib/bind/mydomain.com.hosts: file does not end with newline zone mydomain.com/IN: loading from master file /var/lib/bind/mydomain.com.hosts failed: unexpected end of input zone mydomain.com/IN: not loaded due to errors. _default/mydomain.com/IN: unexpected end of input zone localhost/IN: loaded serial 2 zone 127.in-addr.arpa/IN: loaded serial 1 zone 0.in-addr.arpa/IN: loaded serial 1 zone 255.in-addr.arpa/IN: loaded serial 1 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:20000 ACCEPT tcp -- anywhere anywhere tcp dpt:webmin ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:imaps ACCEPT tcp -- anywhere anywhere tcp dpt:imap2 ACCEPT tcp -- anywhere anywhere tcp dpt:pop3s ACCEPT tcp -- anywhere anywhere tcp dpt:pop3 ACCEPT tcp -- anywhere anywhere tcp dpt:ftp-data ACCEPT tcp -- anywhere anywhere tcp dpt:ftp ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:submission ACCEPT tcp -- anywhere anywhere tcp dpt:smtp ACCEPT tcp -- anywhere anywhere tcp dpt:ssh ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

    Read the article

  • Preparing computers for remote MSI installation in NT4 domain

    - by user40177
    We recently purchased EMCO Remote Installer to deploy MSI packages we're creating. We are still (unfortunately) in an NT4 domain, and when I try to deploy a package using domain's administrator credentials I'm getting "access denied". Under the "requirements for remote computers" section on the EMCO website (http://www.emco.is/products/remote-installer/requirements.php), it says that it requires remote machines to have: * Started services: Computer Browser, Remote Registry * File and Printer sharing enabled * Windows Installer 3.1 * TCP ports opened: 135, 139, 445 * UDP ports opened: 137, 138 Is there any way of scripting these changes? If so, could someone get me started? I have about 200 machines I need to get this working with. Thanks for all your help!!

    Read the article

  • Two Routers - 1 Port Straight to First Router

    - by apples
    At my house we have two Wifi routers one's connected directly to the modem and the other is plugged in down stairs as a second network(Directly connected to the first router) Is there a way that I could make it so that I have the second router have its own network, but have one or two ports that would act as if they were directly connected to the first router? That way I can port forward to devices on the second router. Here are the information about the routers: Router 1 - Linksys WRT54G Running stock firmware Router 2 - Linksys E900 Running Tomato Firmware So to summarize what I'm asking is how would I have two networks from two routers but be able to connect directly to the first router through one of the ports on the second router. Here's a Visio Drawing of what I would like to look like

    Read the article

  • How do I combine static and dynamic DHCP leases on a Cisco router?

    - by Brad
    Basically, what I need is super similar to the unanswered cisco forum question below: https://supportforums.cisco.com/message/3139749#3139749 I have a Cisco 850 Series router. I have configured a DHCP pool for the 10.0.0.0/24 network. I have excluded 10.0.0.1 - 10.0.0.99 from the DHCP pool. I want to add a static DHCP pool for stuff and I want DHCP to statically assign them the addresses of my choice below 100. Actually, I don't care what addresses I statically assign. They can be anything in the pool for all I care, I just want it to work. Why are you doing this? Just statically assign the IPs on the devices! I don't want to do this because I have some laptop users. They could obviously only use that static IP here. This isn't a problem if they could be bothered to change any location setting or something. They can't. So it HAS to be DHCP. It also has to be static IPs because I need to forward ports to them. I know, I know, this is weird but it's an apartment LAN/WLAN so this isn't exactly a typical use case. Relevant sections of config below: ip dhcp excluded-address 10.0.0.1 10.0.0.99 ! ip dhcp pool Internal-net import all network 10.0.0.0 255.255.255.0 default-router 10.0.0.1 domain-name 1770.local lease 7 ! ip dhcp pool static-pool import all origin file flash://staticmap default-router 10.0.0.1 domain-name 1770.local Contents of staticmap: *time* Aug 5 2010 09:00 AM *version* 2 !IP address Type Hardware address Lease expiration 10.0.0.100/24 1 001f.5b3e.d50a Infinite *end* You can see here I was trying addresses outside the excluded-address range to see if that would make any difference. My testing machine's MAC: mainframe:~ brad$ ifconfig en1 en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:1f:5b:3e:d5:0a What shows up in the DHCP binding table: basestar#show ip dhcp binding Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 10.0.0.112 0100.1f5b.3ed5.0a Aug 12 2010 10:06 AM Automatic What's up with the funny looking MAC in the DHCP binding table?? Is what I'm trying to accomplish basically impossible? Am I going about this the wrong way? All I want to to be able to port forward some ports to specific devices. The way I would do this with a consumer router is to do what I'm trying to do here; assign static DHCP to those devices then configure PAT for ports on those addresses.

    Read the article

  • Using "enterprise" switches in home network?

    - by Industrial
    Hi everyone, After more than 12 years working with computers, I am still way behind when it comes to networking, so please bear with me :) As of this Christmas, the number of computers in my home has increased and it's well about time to upgrade the current network hardware in order to offer LAN connection to all computers. Trying to find a cheap solution, A close friend offered me a great deal on a "enterprise-class" Switch from HP (more LAN ports than I would ever need), at the same price as what a brand new Netgear or D-link Switch with 6/8 ports would cost me in retail. Would it be common sense to get this one and start using it immediately and never again have to worry about running out of LAN connections, or am I taking on a bigger bite than what I could chew?

    Read the article

  • Windows Server 2003 Router with PortForwarding

    - by jM2.me
    Hello, I am owning a small company and we have purchased a server to setup few server applications on it as well as other software. We would like to setup our network in following way Internet<-WindowsServer2003 as router<-Switch<-Office Computers Server has two nic interfaces and we have 24ports 1GB network switch connected to one nic and internet connection to another nic. Our ISP is Frontier and we have Fios 25/25. We get network cable out of ONT box directly connected to our server. There are no modems/routers. Setting up DHCP on windows 2003 is easy job but we would like to have the ability to port forward some ports from office computers. I have some knowledge in networking but not as much. How could I setup FHCP server on win2k3 with the ability to port forward some ports to office computers? Thank you for your time

    Read the article

  • Crossover cable in addition to normal network connection on servers?

    - by Zero0ne
    I have 2 servers, both with Windows 2003 R2 Each have 2 NIC ports that are 10/100/1000 They are both connected to our LAN + joined to the domain (1 NIC port free on each server) The problem is that our main router is only 10/100 on the ports that these servers are connected to. Since one server is going to host SQL 2005 and the other will be running Altiris NS7, I was hoping that I could use a crossover cable to connect the two directly, thus taking advantage of their 1gbps NIC cards. Is this possible? If so what steps do I need to take to accomplish this? What needs to be done to make sure that when the app server is communicating with the SQL server that it is using the direct link vs traversing the LAN? Thanks a lot!

    Read the article

  • Routing to various node.js servers on same machine

    - by Dtang
    I'd like to set up multiple node.js servers on the same machine (but listening on different ports) for different projects (so I can pull any down to edit code without affecting the others). However I want to be able to access these web apps from a browser without typing in the port number, and instead map different urls to different ports: e.g. 45.23.12.01/app - 45.23.12.01:8001. I've considered using node-http-proxy for this, but it doesn't yet support SSL. My hunch is that nginx might be the most suitable. I've never set up nginx before - what configuration do I need to do? The examples of config files I've seen only deal with subdomains, which I don't have. Alternatively, is there a better (stable, hassle-free) way of hosting multiple apps under the same IP address?

    Read the article

  • Recommendations for a JetDirect print server for USB 2.0 printers?

    - by eleven81
    I have been using some older HP JetDirect 300x print servers for a variety of parallel printers over the years. These things work great for every printer I have tried them with, including HP's, Dell's, and even a Mountbatten braille embosser! These have been a boon for printers whose internal network cards fail, but whose parallel ports continue working. I don't have to throw away the $500 printer that is one year and a week old, and can keep using it for many, many years. Now that very few printers are coming with parallel ports, but are coming solely with USB connections and network cards. When the network card fails but the printer is still usable, I want to continue using it on the network with a JetDirect card. In summary: Does anyone have any recommendations for JetDirect cards that will work as well with USB 2.0 printers of unspecified manufacturer that my old JetDirect 300x cards do?

    Read the article

  • Does anyone know about nagios plugin that uses nmap and does port checking??

    - by Eedoh
    Hi to all. I need to monitor open and closed ports on dozens of hosts. I've found a Nagios plugin that does what I need, but I would have to use this script through nrpe. Some of the hosts are powered by linux and they all have perl installed. But some of them are Windows machines, and it's not convenient for me to install perl on every one of them. That's why I can not use this plugin. I hope that there's Nagios plugin that uses nmap, or something similar, so it could check ports on every host remotely, without installing plugins on remote hosts, only on server.

    Read the article

  • Does an unmanaged 4/8-port GBit Ethernet switch with a GBIC port exist?

    - by Aaron Digulla
    I'm looking for a simple unmanaged switch with 4-8 GBit Ethernet ports and a fiber port (either as a GBIC slot or pre-installed with a 1000BASE-SX port). Does something like that exist? [EDIT] I want to connect to places in my home without drilling large holes though the floors. Therefore, I'm looking for a cheap way to connect two GBit switches via fiber. I tried with a media converter (GBit <- multimode fiber) but that costs about 50% throughput. So I was hoping that there is a cheap, small GBit switch which has a GBIC slot). All I found so far are very expensive managed switches with 12 or 24 ports for industry use.

    Read the article

  • replacing 3 Cisco Catalyst 4500

    - by hoberion
    Our network supplier recommends replacing our 3 cisco catalyst 4500's because they are EOL and dont speak OSPF (which we really want) Its not my area of expertise so I cant say for sure if we really need to replace these units but for my company the estimated costs of 250K euro is a huge problem. Is there any way to cut down on costs (without moving from cisco devices), I heard the 4500´s can speak ospf but would need an upgrade of sorts? edit: version: IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version 12.2(20)EW, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) supervisor: WS-X4013+ Cisco Catalyst 4500 Series Supervisor Engine II-Plus density: WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC) WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45)

    Read the article

  • What kind of router do I need to handle multiple external I.P addresses?

    - by user1308743
    I have 3 dedicated I.P addresses going to a location with a few servers, and 1 RVS4000 router. Right now, only one I.P is being used. I would like a router that can use all 3 I.P addresses and I can make rules like this: IP1:80 goes to ServerA IP2:80 goes to ServerB What kind of router/device with what features do I need to handle this? I will need to set 30-40 rules to forward certain ports to certain servers. Only a couple ports will need to go to IP2 or IP3. Thanks

    Read the article

  • Dual External Monitors Through Docking Station on ASUS G73JW-XT1

    - by user60695
    I am getting an ASUS G73JW-XT1; and I would like to set it up so that I can plug it into a docking station at my desk, and use 2 external monitors (not the laptop display and an additional monitor). The computer supports a DVI and HDMI output, but I cannot find any docking stations that will support two external displays, as well as audio ports and USB ports for other peripherals. Does anybody know of a specific docking station that will do this, or another workaround without having to plug in several things to my laptop every time I bring it to my desk?

    Read the article

  • How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

    - by vm370
    as you can see from my question, I have a VLAN configuration problem with a ProCurve3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I cannot modify ports to be assigned to a different VLAN or the Default VLAN. I always get the message "config failed", which is not very helpful. When I try to do it over telnet, the router somehow partially crashes and somehow the utilization on all ports is at 100% and I can barely use the web ui. After a reboot everything is fine again, but the configuration was not changed... The traffic after this partial crash looks like a broadcast storm, however there are definitely no loops in the segment. I also updated to the latest stable firmware, but the problem persists. Thanks a lot in advance Br vm370

    Read the article

  • Building boost 1.42 on FreeBSD 6.3

    - by Ivan Perekluyev
    Hi, i need to build mapnik on freebsd 6.3, but port marked as 'broken', so i forced to build it from source. With boost 1.41 (which is in ports) mapnik doesn't build. somewhere in internet, i found that mapnik successfully builded with boost 1.42. So, i download patch from wiki.freebsd.org/BoostPortingProject andd apply it: wget http://alexanderchuranov.com/boost-port/boost-from-1.41-to-1.42-2010-02-16-17-11.diff cd /usr/ports patch -p0 -i ~/boost-from-1.41-to-1.42-2010-02-16-17-11.diff after that, i trying to install boost-all metaport, but its failed. cd devel/boost-all make install 2>&1 | tee build.log tail -n 100 build.log > short_build.log Build.log (attention, 5m !): dl.dropbox.com/u/7365614/build.log Short build log: http://paste.pocoo.org/show/224474/ Thanks!

    Read the article

  • Accessing Windows 7 Printer from Ubuntu Linux via LPR/LPD or Samba

    - by nitbuntu
    Hi, I'm having difficulty printing from my Linux (Ubuntu 10.04) based PC to a printer connected to a Windows 7 machine. I was trying to connect using Samba (version 3.5.6) but this always brings up an authentication screen which never accepts any password I use. So I read somewhere that an alternative is to access the Windows printer via LPR/LPD. I added an LPR/LPD printer in Windows 7, but even within Windows 7, I am not able to print as the print que monitor shows as 'printer busy'. The printer in question is an Epson Stylus DX7400 and works fine when using the standard USB ports....but doesn't when I use with the LPR/LPD ports. I even opened up the TCP/IP port 515 in my McAfee firewall without any success. Any help with this would be highly appreciated. Additionally, does anyone have any idea how I can get Samba working for me?

    Read the article

  • CISCO WS-C4948-10GE SFP+?

    - by Brian Lovett
    I have a pair of CISCO WS-C4948-10GE's that we need to connect to a new switch that has SFP+ and QSFP ports. Is there an X2 module that supports this? If so, can someone name the part number that will work? I have found some information, but want to make sure I have the correct part number for our exact switches. Per the discussion in the comments, I believe I have a better understanding of things now. Would I be correct in saying that I need these SR modules on the cisco side: [url]http://www.ebay.com/itm/Cisco-original-used-X2-10GB-SR-V02-/281228948970?pt=LH_DefaultDomain_0&hash=item417a8d35ea[/url] Then, on the switch with sfp+ ports, I can pick up an SR to SFP+ transceiver like this: [url]http://www.advantageoptics.com/SFP-10G-SR_lp.html?gclid=CKP4s-G27b4CFXQiMgodLD8AQA[/url] and finally, an SR calbe such as this: [url]http://www.colfaxdirect.com/store/pc/viewPrd.asp?idproduct=1551[/url] Am I on the right track here?

    Read the article

  • Limit maximum incoming connections to a port using iptables

    - by Harley
    I have a server that has apache listening on a number of ports. Some ports are used for configuring the server, and another is used to download large files. My problem is that when I have a large number of clients downloading files, the web interface is uncontactable. I would like to limit the number of clients connecting on the "large file" port so that apache always has available connections to configure the server. A REJECT is fine, the client trying to download the file will back off and retry later. Each client only has one connection open to the server at a time, so limiting by IP won't work. I know I could put something in front of apache to manage this, but I'd really like to do it in iptables, without adding more software.

    Read the article

  • Security measures for CentOS

    - by cappuccinodrinker
    I have been tightening up my web server security and wanted to know what else I can do. I am running CentOS 5 with these measures: - All passwords to FTP, MySQL etc are generated from grc.com/passwords.htm and microsoft.com/protect/fraud/passwords/create.aspx (for the ones which cannot be too long). - Running iptables with all ports shut off except for http mail and smtp, the important ports like FTP SSH are blocked to all except my static office IP. There is also no response to pings. - Rootkit Hunter running daily - The server is PCI compliant according to Comodo - Not running any crappy made php apps, we use Zend Framework for our stuff and do have kayako installed and keep them up to date. Can't really think of anything else I can do... I could implement a brute force measure, but I think I already have by simply changing my SSH port to a number above 10000 and blocking it off with iptables.

    Read the article

  • Z77 Motherboard with i7-2600K cpu, what will not work?

    - by Mxx
    I'm building a new system. So far I think I narrowed it down to Gigabyte GA-Z77X-UD5H (Z77 Ivy Bridge chipset) motherboard. I was planning to get i5-3570K(Ivy Bridge) cpu, but now I can get i7-2600K(Sandy Bridge) cpu for free. It is my understanding that Ivy Bridge platform brings support for PCIe3 and (additional?)USB3 ports. If I were to put SB cpu into IB motherboard, what is going to happen to PCIe3 slot? Will it not work at all or downgrade to PCIe2? Also, what is the situation with USB3 ports?

    Read the article

  • VoIP on Netgear DGN 2000 and Lynksys PAP2

    - by David Brown
    I have a VoIP service running perfectly for outgoing calls but I cannot receive incoming calls. I have a Netgear DGN 2000 modem router on 192.168.0.1 and a Lynksys Phone Adapter PAP2 on 192.168.0.2. I have created 3 new custom services: Service Table Service Name Ports tlenfon(TCP) 5060 tlenfon2(UDP) 15000 tlenfon3(UDP) 35000 I have reserved the address 192.168.0.2 for the PAP 2 I have forwarded the ports for each service to the PAP2 Service Name Action LAN Server IP address WAN Users Log tlenfon ALLOW always 192.168.0.2 Any Always tlenfon2 ALLOW always 192.168.0.2 Any Always tlenfon3 ALLOW always 192.168.0.2 Any Always I have checked the Default DMZ and specified 192.168.0.2 What have I missed?

    Read the article

  • SSH tunnel & Rsync thru two proxy/firewalls

    - by cajwine
    Screnario: [internal_server_1]AA------AB[firewall_1]AC----+ 10.2.0.3-^ ^-10.2.0.2 | internet 10.3.0.3-v v-10.3.0.2 | [internal_server_2]BA------BB[firewall_2]BC----+ Ports AC,BC has valid internet addresses. All systems run linux and have root acces to all. Need securely rsync internal_server_1:/some/path into internal_server_2:/another/path My idea is make ssh secure tunnel between two firewalls, e.g. from firewall_1 firewall1# ssh -N -p 22 -c 3des user2@firewall_2.example.com -L xxx/10.3.0.3/xxxx and after will run rsync from internal_server_1 somewhat like: intenal1# rsync -az /some/path [email protected]:/another/path I don't know how to make a correct ssh tunnel for rsync (what ports need tunnel) and to where i will make the rsync? (remote comp address in case of ssh tunnel) Any idea or pointer to helpfull internet resource for this case? thanx.

    Read the article

  • Do these 3 crashes have something in common?

    - by David U
    I'm running OS X 10.6.8 on a Mac Mini. I tried to install 3 applications today and all 3 installations failed. I am wondering if the failures have something in common. First I installed GraphViz. The installation succeeded, but when I try to open any .dot file, I get a dialog that says GraphViz has quit unexpectedly. Next I installed Doxygen. It installed, but when I try to launch it I get a dialog that tells me Doxywizard quit unexpectedly. After some googling I thought perhaps my system lacked QT, and that was the problem. I downloaded the Qt 4.8.4 packages and installed them. But when I try to launch qtdemo.app, or any of the other apps that came with the qt installation, I get a dialog that says I can't open the app because it's not supported on this type of Mac. I have crash logs from GraphViz and Doxygen. They're long and I think it unnecessary to post them unless they would help someone determine my problem. Thanks Excerpt from System Log, added later: 12/13/12 5:26:21 PM [0x0-0x4f04f].com.apple.DiskImageMounter[1322] 2012-12-13 17:26:21.927 DiskImages UI Agent[1333:903] *** -[NSMachPort handlePortMessage:]: dropping incoming DO message because the connection or ports are invalid 12/13/12 5:30:31 PM [0x0-0x1a01a].org.mozilla.firefox[824] [ConvConfHandler] isPreferred contentType: application/x-apple-diskimage 12/13/12 5:35:32 PM DiskImages UI Agent[1384] *** -[NSMachPort handlePortMessage:]: dropping incoming DO message because the connection or ports are invalid 12/13/12 5:35:32 PM [0x0-0x5a05a].com.apple.DiskImageMounter[1376] 2012-12-13 17:35:32.988 DiskImages UI Agent[1384:903] *** -[NSMachPort handlePortMessage:]: dropping incoming DO message because the connection or ports are invalid 12/13/12 6:07:33 PM DisplayLinkUserAgent[772] (00116500.405)-[DLDistributedNotificationCenter stream:handleEvent:] reconnected. 12/13/12 6:07:33 PM [0x0-0x6c06c].backupd-helper[1446] Not starting Time Machine backup after wake - less than 60 minutes since last backup completed. 12/13/12 6:08:43 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/BrotherPPD.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/NeoOffice-2.2.3-Intel.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/NeoOffice-2.2.3-Patch-2-Intel.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/NeoOffice-2.2.5-Intel.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/NeoOffice.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/PIXMA iP6000D 290.pkg 12/13/12 6:14:39 PM com.apple.launchd.peruser.501[359] ([0x0-0x70070].com.att.graphviz[2047]) Job appears to have crashed: Bus error 12/13/12 6:14:41 PM ReportCrash[2056] Saved crash report for Graphviz[2047] version 2.28 (2.28.0) to /Users/duzzell/Library/Logs/DiagnosticReports/Graphviz_2012-12-13-181441_Amun.crash 12/13/12 6:15:19 PM com.apple.launchd.peruser.501[359] ([0x0-0x74074].org.doxygen[2070]) Job appears to have crashed: Bus error 12/13/12 6:15:19 PM ReportCrash[2056] Saved crash report for Doxywizard[2070] version 1.8.2 (???) to /Users/duzzell/Library/Logs/DiagnosticReports/Doxywizard_2012-12-13-181519_Amun.crash

    Read the article

  • Can I use an nVidia Geforce 9600GT for triple-monitor?

    - by John Rudy
    My work PC has (as you can guess from the title) a single Geforce 9600GT card. According to the spec page for this card, both DVI ports are Dual-Link DVI. Both are currently in use on Dell 19" 1280x1024 screens. I'm running Windows 7, with Aero enabled, for what that's worth. What I'm wondering is if I can use a standard DVI splitter cable to drive a third screen from one of the ports -- specifically a Samsung 22" 1680x1050. I'm really outgrowing the two-screen setup, and am strongly considering bringing in my home monitor (which is almost never used) to bolster my usable space. If I can't, then my alternative is to replace one of these Dells with that Samsung, to give me at least a "little" more space. (Before you ask, there's probably no chance I can get my company to spring for a second video card and third monitor. Even if I could, it would not be politically expedient, as a number of my other coworkers are already pretty jealous at my setup.)

    Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >