Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 49/172 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• Broadcom NIC Teaming w/ 802.3ad and Dell Powerconnect 2824

  - by Carltoncl

  We have a Poweredge R210 running WS2K8R2. The server has two Broadcom 5716C NICs running Broadcom BASP. I can team the NICs using the 802.3ad protocol on the server end no problem. I have no VLAN. Now I go to the 2824 switch (default settings all round) running in managed mode and create a LAG with ports g1 and g2. As soon as I add these ports, I lose the ability to send traffic to or from the server. I am much more of a server guy than a networking guy, what am I doing wrong here? Server Static IP Address: 10.10.61.15 Network mask: 255.255.255.0 Gateway: 10.10.61.51 The 2824 switch has an IP address of 10.10.61.51 and in turn has its gateway as our firewall server running ISA Server at 10.10.61.50.

  Read the article

• Using Supermicro IPMI behind a Proxy?

  - by Stefan Lasiewski

  This is a SuperMicro server with a X8DT3 motherboard which contains an On-board IPMI BMC. In this case, the BMC is a Winbond WPCM450). I believe many Dell servers use this a similar BMC model. A common practice with IPMI is to isolated it to a private, non-routable network. In our case all IPMI cards are plugged into a private management LAN at 192.168.1.0/24 which has no route to the outside world. If I plug my laptop into the 192.168.1.0/24 network, I can verify that all IPMI features work as expected, including the remote console. I need to access all of the IPMI features from a different network, over some sort of encrypted connection. I tried SSH port forwarding. This works fine for a few servers, however, we have close to 100 of these servers and maintaining a SSH client configuration to forward 6 ports on 100 servers is impractical. So I thought I would try a SOCKS proxy. This works, but it seems that the Remote Console application does not obey my systemwide proxy settings. I setup a SOCKS proxy. Verbose logging allows me to see network activity, and if ports are being forwarded. ssh -v -D 3333 [email protected] I configure my system to use the SOCKS proxy. I confirm that Java is using the SOCKS proxy settings. The SOCKS proxy is working. I connect to the BMC at http://192.168.1.100/ using my webbrowser. I can log in, view the Server Health, power the machine on or off, etc. Since SSH verbose logging is enabled, I can see the progress. Here's where it get's tricky: I click on the "Launch Console" button which downloads a file called jviewer.jnlp. JNLP files are opened with Java Web Start. A Java window opens. The titlebar says says "Redirection Viewer" in the title bar. There are menus for "Video" "Keyboard" "Mouse", etc. This confirms that Java is able to download the application through the proxy, and start the application. 60 seconds later, the application times out and simply says "Error opening video socket". Here's a screenshot. If this worked, I would see a VNC-style window. My SSH logs show no connection attempts to ports 5900/5901. This suggests that the Java application started the VNC application, but that the VNC application ignores the systemwide proxy settings and is thus unable to connect to the remote host. Java seems to obey my systemwide proxy settings, but this VNC application seems to ignore it. Is there any way for me to force this VNC application to use my systemwide proxy settings?

  Read the article

• External USB drive is failing

  - by dma_k

  I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

  Read the article

• Recommendation for Ethernet switches that allow arbitrary network topologies

  - by sblair

  We have the following requirements for three Ethernet switches that will be connected together: Allow the switches to connect together to form dynamic, arbitrary topologies, i.e., support for the RSTP is essential. Allow the physical topology (which ports are connected together) to be gleaned from the switches, e.g., using SNMP traps. This is optional, but would be very useful. At least 5 ports on each switch, but only 3 will be used for connecting the switches together. Be as compact as possible. Ideally be in stock, in the UK. Only 100Mb/s is required. (This question is the result of the lack of RSTP support from 3Com NJ225 devices, as described in my previous question.)

  Read the article

• Looking for a manual/how-to for installing a Canon iRunner 210s network printer

  - by Ssvarc

  A client has a Canon iRunner210S and is complaining about slow print speeds. I've searched for a install manual online but came up empty. A call to Canon technical referred me to their dealer network for service, as as informing me that there isn't a manual available on their website. Anyone know how to install these and/or have a link to a manual? The current setup has the printers on a LAN Manager printer port instead of on straight IP ports. Is this normal for this printer? And what exactly are Lan Manager ports (based on my research, they appear to be a way to authenticate a connection)?

  Read the article

• How to install a Canon iRunner 210s

  - by Ssvarc

  A client has a Canon iRunner210S and is complaining about slow print speeds. I've searched for a install manual online but came up empty. A call to Canon technical referred me to their dealer network for service, as as informing me that there isn't a manual available on their website. Anyone know how to install these and/or have a link to a manual? The current setup has the printers on a LAN Manager printer port instead of on straight IP ports. Is this normal for this printer? And what exactly are Lan Manager ports (based on my research, they appear to be a way to authenticate a connection)?

  Read the article

• Basic proxy with OpenSSH, Cygwin, Putty

  - by clang1234

  I know this is probably a common question, but after looking around for a few hours (on this site and others), I can't find a solution. I'm trying to set up a simple proxy. I already have a server running Windows Server 2008. I've installed Cygwin and have OpenSSH installed. I also have sshd (the openssh daemon) running. Port 22 is forwarded correctly. On my client side I have Putty on a Windows 7 machine. I can successfully open a connection to my server and log in to access the shell. So what do I do next? Do I just name the ports I want tunneled in Putty or do I need to tell my SSH server what to do with those ports? Thanks for the help. Let me know if I left anything out.

  Read the article

• Specify IPSEC port range using ipsec-tools

  - by Sandman4

  Is it possible to require IPSEC on a port range ? I want to require IPSEC for all incoming connections except a few public ports like 80 and 443, but don't want to restrict outgoing connections. My SPD rules would look like: spdadd 0.0.0.0/0 0.0.0.0/0[80] tcp -P in none; spdadd 0.0.0.0/0 0.0.0.0/0[443] tcp -P in none; spdadd 0.0.0.0/0 0.0.0.0/0[0....32767] tcp -P in esp/require/transport; In setkey manpage I see IP ranges, but no mention of port ranges. (The idea is to use IPSEC as a sort of VPN to protect internal communications between multiple servers. Instead of configuring permissions basing on source IPs, or configuring specific ports, I want to demand IPSEC on anything which is not meant to be public - I feel it's less error-prone this way.)

  Read the article

• Setting up a transparent SSL proxy

  - by badunk

  I've got a linux box set up with 2 network cards to inspect traffic going through port 80. One card is used to go out to the internet, the other one is hooked up to a networking switch. The point is to be able to inspect all HTTP and HTTPS traffic on devices hooked up to that switch for debugging purposes. I've written the following rules for iptables: nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.2.1:1337 -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 1337 -A POSTROUTING -s 192.168.2.0/24 -o eth0 -j MASQUERADE On 192.168.2.1:1337, I've got a transparent http proxy using Charles (http://www.charlesproxy.com/) for recording. Everything's fine for port 80, but when I add similar rules for port 443 (SSL) pointing to port 1337, I get an error about invalid message through Charles. I've used SSL proxying on the same computer before with Charles (http://www.charlesproxy.com/documentation/proxying/ssl-proxying/), but have been unsuccessful with doing it transparently for some reason. Some resources I've googled say its not possible - I'm willing to accept that as an answer if someone can explain why. As a note, I have full access to the described set up including all the clients hooked up to the subnet - so I can accept self-signed certs by Charles. The solution doesn't have to be Charles-specific since in theory, any transparent proxy will do. Thanks! Edit: After playing with it a little, I was able to get it working for a specific host. When I modify my iptables to the following (and open 1338 in charles for reverse proxy): nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.2.1:1337 -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 1337 -A PREROUTING -i eth1 -p tcp -m tcp --dport 443 -j DNAT --to-destination 192.168.2.1:1338 -A PREROUTING -i eth1 -p tcp -m tcp --dport 443 -j REDIRECT --to-ports 1338 -A POSTROUTING -s 192.168.2.0/24 -o eth0 -j MASQUERADE I am able to get a response, but with no destination host. In the reverse proxy, if I just specify that everything from 1338 goes to a specific host that I wanted to hit, it performs the hand shake properly and I can turn on SSL proxying to inspect the communication. The setup is less than ideal because I don't want to assume everything from 1338 goes to that host - any idea why the destination host is being stripped? Thanks again

  Read the article

• DYNDNS setup with TightVNC on Windows Server 2008 R2

  - by StealthRT

  Hey all, i seem to be having a problem with getting ports to forward on my Windows Server 2008 R2 PC. I already set all my port forwarding for 5900/5800 on my router for my PC's IP address (192.168.1.22) but when i try to use the TightVNC PFPortChecker on port 5900 it tells me its not opened! I can not even connect to my DYNDNS server name (xxxxxxx.dyndns.org). As a side note, i am running Windows XP SP3 within a VirtaulBox inside Windows Server 2008 R2 but running the PFPortChecker in Windows 2008 R2 brings the same results as it does in the VM. I also added them to the Windows Firewall Advanced Security form to add those inbound ports for full access. What could i possibly be missing? Thanks for your time! David

  Read the article

• HP ProCurve GVRP Setup

  - by Matt

  I'm trying to setup GVRP on my 4 ProCurve switches. Currently I have a Layer 3 3500yl-24G (J8692A) which is connected to 3 Layer 2 2510G-48 (J9280A). I have three trunk ports setup on the 3500 connected to the 3 switches and currently everything seems to be working, the devices are talking to eachother and GVRP is pushing its configurations from the 3500 to the 3 other switches. My question is, once GVRP is setup, how exactly do I configure the ports on the 3 L2 switches to use the correct VLAN? I'm new to ProCurve network equipment and this is much easier to setup on Cisco equipment.

  Read the article

• Using the Juniper EX3300 Switch as a router?

  - by Richard Whitman

  I have a Juniper EX3300 switch in a data center. And I have connected one of the uplink ports (ge-0/1/0) to my ISP's router. I want to configure it so that all the devices connected to ports in the same VLAN as ge-0/1/0 can access the Internet. I have done some research, and I haven't gotten anywhere really. I have configured the interface as follows: ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family inet { address xx.xx.xx.xx/32; } } } where xx.xx.xx.xx is the "Customer Router Port IP" assigned by my ISP. When I try to commit, I get the following error: Interface ge-0/1/0.0 not enabled for switching Can some one tell me what is the right way to configure it?

  Read the article

• DSL Modem with Wireless Router

  - by David

  I have a D-Link WBR-1310 wireless router and a TP-Link TD-8616 DSL modem. My old DSL modem died recently and I got the TP-Link as a replacement. With my old DSL modem, I plugged it into the WAN port on my D-Link and I could reach the internet through wireless and through the network. However, when I plugged the new TP-Link into the WAN port, I was not able to get any internet connectivity (either on the network ports or through wireless). So I plugged my labtop directly into the TP-Link DSL modem and I was able to get internet connectivity. I'm trying to figure out why my labtop can see the internet connection, but not the D-Link router. I think that the problem is due to the IP networking. My D-Link was originally set to have IP address 192.168.1.1. According to the documentation for the TP-Link DSL modem, it uses 192.168.1.1 as its IP address. I do not believe that my old DSL modem had an IP address. I logged into my D-Link router and changed its IP address to 192.168.1.2 and restarted it. Unfortunately, I still could not see the internet from my wireless devices. I've read a few forum postings which implied that I needed to setup a "bridge" between the two networks. Does that sound correct? Why didn't my old DSL modem require a bridge? I read pg. 12-13 of my D-Link's manual and they suggest that I need to disable UPnP, DHCP, and then plug the DSL modem into one of the LAN ports on my router. I'm concerned about doing this since I don't think that the firewall will work if I plug my DSL modem into one of the LAN ports. I also have a home NAS on my network and I wouldn't want that to be available over the internet. Does anyone have any advice about how I can get my TPLink DSL modem to work with my D-Link router? Thanks!

  Read the article

• vagrant up command very slow on OS X Lion

  - by Andy Hume

  When I run vagrant up to provision a new VM on Lion it takes an extremely long time, during which the entire Mac is very laggy and unresponsive. The output is as follows, the key point being the "notice: Finished catalog run in 754.28 seconds" > vagrant up [default] Importing base box 'lucid64'... [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.1.0 VirtualBox Version: 4.1.6 [default] Matching MAC address for NAT networking... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- ssh: 22 => 2222 (adapter 1) [default] -- web: 80 => 4567 (adapter 1) [default] Creating shared folders metadata... [default] Running any VM customizations... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] VM booted and ready for use! [default] Mounting shared folders... [default] -- v-root: /vagrant [default] -- v-data: /var/www [default] -- manifests: /tmp/vagrant-puppet/manifests [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: /Stage[main]/Lucid64/Package[apache2]/ensure: ensure changed 'purged' to 'present' [default] [default] notice: /Stage[main]/Lucid64/File[/etc/motd]/ensure: defined content as '{md5}a25e31ba9b8489da9cd5751c447a1741' [default] [default] notice: Finished catalog run in 754.28 seconds [default] [default] err: /File[/var/lib/puppet/rrd]/ensure: change from absent to directory failed: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: change from absent to directory failed: Could not find group puppet [default] [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: Finished catalog run in 2.05 seconds [default] [default] err: /File[/var/lib/puppet/rrd]: Could not evaluate: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: Could not evaluate: Could not find group puppet [default] [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: Finished catalog run in 1.36 seconds [default] [default] err: /File[/var/lib/puppet/rrd]: Could not evaluate: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: Could not evaluate: Could not find group puppet [default] >

  Read the article

• How to make a normal user can install package with `pkg_add` on FreeBSD?

  - by Eonil

  How to make a normal user can install package with pkg_add on FreeBSD? pkg_add -r command fails with normal user with sudo. Downloading succeeds, but installation fails with this error message. Equal command executed successfully with root login. %sudo pkg_add -r apache22 Password: Error: Unable to get ftp://ftp.freebsd.org/pub/FreeBSD/ports/amd64/packages-8.1-release/Latest/apache22.tbz: Syntax error, command unrecognized pkg_add: unable to fetch 'ftp://ftp.freebsd.org/pub/FreeBSD/ports/amd64/packages-8.1-release/Latest/apache22.tbz' by URL % Assume my username as eonil. I added eonil ALL=(ALL) ALL code as next of root ALL=(ALL) ALL via visudo, and added the user to wheel group by pw usermod eonil -G wheel . But the user cannot install package with sudo pkg_add -r apache22. (not only the apache, any package.)

  Read the article

• Windows 7 port Forwarding Issue

  - by Elliot

  I can't get port forwarding to work now that I am using windows 7 (64-bit). I am using a wireless connection (no wired connection available). I have the ports forwarded (IP has been double checked, router settings are confirmed), there is an exception for all of the programs in question in windows firewall, and in the resource monitor windows lists the ports as available, not restricted, and yet when I either use a specific program (ie utorrent, DC++, Command & Conquer 3) or check using firefox, the port reads as closed. How do I get the port forwarding to work?

  Read the article

• Good HDMI splitter/switch solution

  - by Mehper C. Palavuzlar

  I have a full HD TV which has only 2 HDMI ports on it. Since I have more than 2 devices I connect to TV (e.g. laptop, game console, DVD player), it becomes uncomfortable to plug in and plug out HDMI cables every time I need to use the relevant device. I need a cheap solution to increase the number of my HDMI ports at least to 3. What type of splitter/switch do you recommend? Does the quality of splitter matter, or do they all produce the same audio & video quality?

  Read the article

• No communication on my VLAN?

  - by Donovan

  I am using a Netgear FSM7328S switch and have designated ports 19-24 as being part of VLAN # 3. I designated them all as untagged because I do not want them to switch traffic to any other port on the switch. I also removed them from the default, untagged, VLAN 1. My issue is that none of the ports 19-24 will communicate with eachother. My laptop plugged in with wireshark shows no switched traffic what so ever. Have I configured it wrong? Thanks, D

  Read the article

• Wireshark (WinPCap) does not see Intel X520-DA2 10 GbE NIC teaming intermittently

  - by GregC

  I am running a team of two 10 GigE ports on Intel X520-DA2 network card. They work well in tandem and achieve the desired throughput. However, I see an intermittent issue whereby WireShark and my own application (using WinPCap) only show the underlying ports, failing to recognize the team adapter. Details: Intel 17.4 NIC drivers on Windows Server 2008 R2 with all patches. HP DL370 G6 server. RSS enabled on Intel both underlying Intel NICs. The exact error: Unable to open the adapter (rpcap://\Device\NPF_{401D5903-16E7-41DC-8484-5D96765B9692}). failed to set hardware filter to promiscuous mode

  Read the article

• Windows 2008R2 blocks outbound LDAP for non-admins?

  - by Jon Bailey

  I've got a Windows 2008R2 terminal server with ~30 users on it. It's joined to a Samba-based domain. During the login script, we connect directly to the LDAP server to pull out certain profile information. This used to work just fine. Now, it doesn't, but only for non-local-admin accounts. Local admins work fine. As a non-local-admin: Connection to ports 389 or 636 just terminate (wireshark on the LDAP server reveals no connection attempt) Connection to other ports on the same server work fine Same thing on multiple LDAP servers Windows firewall is disabled Can't find any other rules/policies that may block this I suspect since this used to work, it came down during an update, but for the life of me, I can't find what. EDIT: I just ran Wireshark on the machine and didn't see anything when connecting to the LDAP server in question (or any LDAP server for that matter). I can, however, see traffic when I connect to that server on another port.

  Read the article

• ESXi and Networking Devices

  - by EsxiUser

  I have two intel pro 1000 pt nics. One quad and one dual port. I want to assign all nic ports to a VM. I enabled PCI passthrough on all devices but ESXi will only allow me to add two nic ports until it tells me the maximum number of pci devices have been added. I have also tried setting up a virtual switch but it didn't seem like this would give full access to the nics. What is the best way to setup the nics to the VM has direct access to them? This is for a firewall VM.

  Read the article

• ICMP - TTL - Trace Route

  - by dbasnett

  I asked this question at Stack Overflow and then thought this may be the better place to ask. Given the following situation: PC --- |aa RTR1 bb| --- |aa RTR2 bb| --- |aa RTR3 bb| etc Each of the |aa rtr bb| is meant to be a router with two ports aa and bb. My question is this. When you do a trace route from PC which router port address should respond with time to live exceeded in transit message? I seem to remember being taught to think of the router as being in as many parts as ports, so that in my scenario when aa is forwarding the packet to bb and decrements the ttl to 0, it will be the address of the aa port in the failure message. I am trying to find the definitive answer. Thanks.

  Read the article

• Good HDMI splitter solution

  - by Mehper C. Palavuzlar

  I have a full HD TV which has only 2 HDMI ports on it. Since I have more than 2 devices I connect to TV (e.g. laptop, game console, DVD player), it becomes uncomfortable to plug in and plug out HDMI cables every time I need to use the relevant device. I need a cheap solution to increase the number of my HDMI ports at least to 3. What type of splitter do you recommend? Does the quality of splitter matter, or do they all produce the same audio & video quality?

  Read the article

• Issue with Netgear GS108T Managed Switch and Jumbo Frames

  - by Richie086

  I recently purchased a Netgear GS108T managed switch and I am trying to configure jumbo packets between my NAS (Thecus N4100Pro), PC and managed switch. I should mention the fact that I was able to use jumbo frames between my PC and NAS before I purchased the switch without issue. My Desktop has a wired gigabit NIC (Intel 82579V Gigabit) and has the ability to configure jumbo frames (see pic) that are either 9014 bytes or 4088 bytes. I choose 9014 bytes for the jumbo frame size My NAS supports jumbo frames as well, and is configured to use 9014 as the frame size. When I go into my Netgear managed switch and set the frame size to 9014 on the ports I am using for my PC and NAS. See image As soon as I hit apply in the web interface, I loose my connection to the SMB shares on my NAS and I can no longer connect to the web admin interface for my NAS. The really strange thing is I can ping my NAS via the ping command, but when I try to connect to the web interface on port 80 or port 443 the page never loads. I did a scan from my PC to my NAS using nmap and I can see the following ports open PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 631/tcp open ipp 2000/tcp open cisco-sccp 2049/tcp open nfs 3260/tcp open iscsi 49152/tcp open unknown MAC Address: 00:14:FD:15:00:44 (Thecus Technology) Read data files from: C:\Program Files (x86)\Nmap Nmap done: 1 IP address (1 host up) scanned in 211.97 seconds Raw packets sent: 1 (28B) | Rcvd: 1 (28B) Anyone have any idea what is going on here? Why is nmap able to detect the ports are open and listening for http, https and file sharing but I cant connect when all devices have jumbo packets enabled? Stranger still - I did a packet capture using wireshark while the nmap scan was running and filtered so I only saw converstations between my PC and my NAS. Here are the packet details from my scan Only 4 packets over 5k bytes? What is going on here? Do I not need to configure jumbo frame sizes on the switch? I have an internet connection from my pc to the switch to my router - I just cannot connect to my NAS. I just checked on my iPhone and I am able to open my NAS web admin interface without issue on my iPhone! WTF!!!!!! Let me know if you need more details..

  Read the article

• Apache not running from rc.d on FreeBSD

  - by Oksana Molotova

  I'm using FreeBSD 8.3 and Apache 2.2. I didn't install Apache from ports, instead compiled it from source because I wanted to move the binary and configuration to a different path (I'm centering all of the major production daemons and their configurations in a single place). In any case, I based the /usr/local/etc/rc.d/apache22 file on one from a different server where it was installed from ports, I only modified the binary and config paths within. I can manually execute it with /usr/local/etc/rc.d/apache22 start, however even with apache22_enable="YES" in /etc/rc.conf it fails to start. All permissions and ownership are identical to the other server where it works. What am I missing and is there a way to debug this kind of thing?

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >