Search Results

Search found 4477 results on 180 pages for 'wireless keyboards'.

Page 51/180 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

  • Check connection and reconnect wifi

    - by Ruud
    I'm building a wireless photoframe. The one thing I haven't been able to figure out is how to get my wifi connection back up using a recommended method. Right now I edited /etc/network/interfaces so wlan0 is started at boot: auto wlan0 iface wlan0 inet dhcp wireless-essid ourssid This method works fine for booting. But I found that if I do not check the connection for a long time (could be a week) it might be down. So I should reconnect. What I do now to verify the connection is working is downloading a file from the server that can't be cached (http://server.ext/ping.php?randomize=123456) If I fail to retrieve the file I assume that the connection is no longer working and I run a shell script like #!/bin/bash ifconfig wlan0 up iwconfig wlan0 essid "ourssid" dhclient wlan0 And the connection comes back. But I can't find anything if this is in any way a good method. Can this be improved upon, or is this already right?

    Read the article

  • Wi-fi interface fails to authenticate on secured networks

    - by Eduardo Bezerra
    the problem is that I can't connect to wireless networks that have security enabled. I can connect fine to the unsecured network of my university, but not to the secured one in the same building. Also, it fails to connect to my home wireless router, which uses wpa2 encryption. Any ideas? I have a Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01), with pci id [14e4:4353], running Ubuntu 12.10 on a macbook pro 6,2. I'm using bcmwl-kernel-source package with kernel module wl to enable my wi-fi device.

    Read the article

  • Netgear WNA1100 stopped working

    - by NOLFXceptMe
    I'm facing a rather strange issue with the USB wireless adapter WNA1100. I was able to connect to wireless using this yesterday. However, today am not. lsmod shows ath9k_htc, ath9k_common, ath9k_hw, ath and ndiswrapper. I'm not sure if this is relevant to the above problem, but between yesterday and today, the only change was an upgrade to Ubuntu 2.6.38 kernel, which caused the NVIDIA driver to break (I have a 7300GT), so I had to ignore that kernel, reboot into 2.6.35, and rebuild NVIDIA module from NVIDIA-Installer-270.run. Help?

    Read the article

  • Dell Vostro 2420 upgrade to 12.04.1 no wifi

    - by Kane
    I have installed 12.04 on a dell vostro 2420 (previously 11.10) and wifi is gone now but wired network remains. I've reviewed the other questions and tried some stuff but no luck yet. The following is the process so far so hopefully someone can help: After installing 12.04 using the additional drivers utility did not bring up any proprietary drivers and using synaptic on installation then reinstallation of bcmwl-kernel-source and b43-fwcutter does not help bring up any drivers either (tried rebooting after as well) I have made sure in the bios that the wlan is turned on, and it appears the laptop does not have a wireless hardware switch, only the keyboard function shortcut which turns bluetooth on and off on the taskbar but there is no lightup of the wireless function on the laptop itself. Dell does not appear to have any drivers for ubuntu and google does not appear to be much help :( Thanks in advance!

    Read the article

  • ralink rt2860 not working anymore in ubuntu 12.10

    - by greenit
    I just upgraded from Ubuntu 12.04 to 12.10, however, my network card is not working anymore... When i had 12.04 installed, i just had to download the driver from Ralink, go to the directory and enter these commands: $ make $ sudo make install and the network card worked... now, when I want to do this in ubuntu 12.10, it seems like it works, but it doesn't. I can enable the module, it recognizes the network card, but i am unable to connect to any wireless network... How can i get my wireless card working again? If any1 knows a solution, please tell it to me, thx in advance

    Read the article

  • Do I need a wifi card to have internet access?

    - by Sarah
    I am attempting to set up a wireless network on 11.04, freshly download today. The router is on and working. However, I do not have a wifi "card" (which I am assuming is a little USB-type thing that allows internet access, but correct me if I am wrong) and every time I try to type in the MAC address and everything, nothing works. I also get the "firmware missing" error when I scroll over the signal strength, which I have tried looking up but have been unsuccessful with completely understanding it. I guess my main question is do I need another little device to be able to use wifi on my ubuntu? I do have an ethernet cable but another person is using it and I do not want to be tied down to that cable. the problem is that none of the wireless networks show up, however they show up when I go into Windows mode on my laptop. I get an error message at the top saying "firmware missing" which I have tried looking up but still have no straight answer for.

    Read the article

  • Ubuntu 12.04, can't find my home wifi network

    - by Anton
    I've tried several solutions I found on the web, but didn't manage to solve a problem. Since today my laptop won't find my WiFi network, but neighbours' networks are suggested. Another laptop with U12.04 does find one. What do I do? I've Dell Latitude-E4310, 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f2c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac also NetworkManager Tool State: connected (global) - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: wl State: disconnected Default: no HW Address: 1C:65:9D:7A:45:5C Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Should I provide anything else? Many thanks in advance.

    Read the article

  • slow speed transfering files to a local network device

    - by F. Ariel Jung
    I'm having troubles copying files from my pc(ubuntu 13.04 64 bits) to a Media Center(WDTV Live: with an SATA2 HDD attached) through the local network. the speed is to slow, it's up to 2.0 MB/s image: http://s11.postimg.org/g1nuai92b/Captura_de_pantalla_de_2013_06_24_07_46_55.png (I don't use image tag because it is a big image) my PC has a wifi network card Tp Link TL-WN951N and it is connected to a TP Link TL-WDR3500 router via wifi, and the WDTV Live is connected via LAN here is a iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TL-WDR3500" Mode:Managed Frequency:2.462 GHz Access Point: A0:F3:C1:6C:3B:F1 Bit Rate=39 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:33521 Invalid misc:2245290 Missed beacon:0 if more data is required I'll post it as needed. I can't figure this out, needed help. please

    Read the article

  • How to install Netgear N-300 UAB adapter WNA3100 on Ubuntu 12.04

    - by JacobusR
    After a fresh install of Ubuntu 12.04, the first thing I'm trying to do, is to setup my wireless adapter. I can see it using lsusb: beer@beer-linux:~$ lsusb ... Bus 002 Device 006: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] ... I have found a lot of dated instructions on the net and just wanted to know what the right way is to set it up on 12.04. I don't want to mess up a brand new install by tweaking things that don't need tweaking. According to most posts, you have to install the Windows drivers using the ndiswrapper package. Is this still the right way to go? If so, it would be great if someone could write down the steps to do this under 12.04

    Read the article

  • Update drivers for TL-WN851ND

    - by Tony_GPR
    Today I bought a new PCI wireless card, TP-Link WN851ND, with Atheros AR9227 chipset. It has 2 antennas and is compatible with Wifi N so I thought it would improve the quality of the signal. But after install it on my computer the result is the opposite to expected. It doesn't connect to my network, while my old Wifi BG card connect without problems, I created an access point from my smartphone to try the card, and work, but is very slow loading pages. In Windows 7 works perfectly, so I think the problem is the driver. I have Ubuntu 12.04 LTS with kernel 3.2.0.31, is there a way to update the driver or I can apply a patch to improve the performance of the card? Otherwise, anyone know if there is a work in progress to improve compatibility with this chipset, or is it better to change the card and buy one with better driver compatibility. And finally, which wireless N compatible chipsets have good support under Linux/Ubuntu?

    Read the article

  • Wifi networks will not show up!

    - by Kcahmadi
    I'm running Ubuntu 14.04 on an old '08 macbook. I've gone to system settingsSoftware & UpdatesAdditional Drivers and enabled the wireless driver. But when I click the wifi icon on the top toolbar no networks show up. When running lshw it clearly shows my wireless card under Network controller and it says the driver is installed. However, nm-tool only shows ethernet. And rfkill only shows bluetooth. What can I do?

    Read the article

  • How do I get the Netgear N150 USB wifi adapter working on 12.04?

    - by Jon
    Just installed latest version of ubuntu. I'm using a Netgear N150 Wireless USB Micro Adapter WNA1000M which keeps asking for network password over and over. I read elsewhere that I needed to install the latest driver for my chipset (RTL8188CUS) which I have and still no joy. If I run the steps listed in this thread while connected through ethernet, the wireless will connect just fine. If I disconnect the ethernet, the wifi will even continue to work, but after a restart or two I will lose connection. If I repeat the steps listed in the aforementioned thread, it will not re-connect wifi unless I run those steps while connected to ethernet.......so strange...

    Read the article

  • Cannot get Atheros AR9285 to work on 12.10

    - by user100449
    I've already went through all possible advices and still cannot start my Atheros AR9285 wireless card. I have a laptop Toshiba Portege Z830 where the WiFi already worked under Windows 7. But after migration on Ubuntu 12.10. I'm not able get it work. This is what I see on command lshw *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0500000-c050ffff This is what I see on command rfkill list 0: Toshiba Bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 1: hci0: Bluetooth Soft blocked: yes Hard blocked: no Any idea?

    Read the article

  • How to setup 802.11n wireless card in ubuntu

    - by michael
    Hi, I have installed ubuntu 9.10 on my laptop. It has a 802.11n wireless card. When I boot up to ubuntu, the wireless does not work. And if I connect to a wire network within ubuntu, it works. Can you please tell me how can I setup my wireless card in ubuntu 9.10? Thank you.

    Read the article

  • Unstable Wifi and Spontaneous Low-graphic Error with Pavilion DV4

    - by Constant Dean
    I've been having numerous problems with connectivity through WiFi. It had been working for a few days and now it doesn't. On top of that around 40% of every time I turn on the laptop it shows "System running in low-graphics" error and I'm unable to view the desktop (sometimes not even able to access terminal), therefore having to manually power-down until it finally works. I use Ubuntu 12.10. nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: r8169 State: connected Default: yes HW Address: 84:34:97:6B:2E:D7 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.10 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 DNS: 68.237.161.12 - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: rt2800pci State: unavailable Default: no HW Address: 68:94:23:50:A5:D9 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points

    Read the article

  • Network Manager troubleshooting

    - by Anero
    I'm having some issues when connecting to my house's wifi from my Ubuntu 10.10 laptop. If the connection doesn't exists, when selecting the network (and after entering the WPA2 password) I'm able to connect. Once the connection is saved, when trying to reconnect, Network Manager works for a minute or so and then fails; the only way to reconnect then is to delete the saved connection and re-select the network from the list of available wireless networks. The same network works with no issues on the same laptop when running Win7, and on other wireless networks when running Ubuntu. Is there a Network Manager log which I can take a look at for troubleshooting the issue? Are there any tools for checking the wifi status?

    Read the article

  • Ubuntu 12.04 crashes on startup for newer versions of Linux, possibly related to WiFi

    - by Jake
    My computer gets to the screen with the Ubuntu logo and the orange/white dots, and then the screen goes black, spits out a lot of error messages, and cannot boot. (If it'd be helpful, I can take a photo of my screen in this state.) I've found I can successfully boot if my wireless card is turned off. As soon as I turn it on, my computer crashes with the same black screen of death. I can also successfully boot if I choose "Previous Linux Version" and select a few versions back (I think 3.0.6). Here are some relevant details about my setup: Ubuntu 12.04 Computer: Lenovo x230 Wireless: Realtek RTL8188CE 802.11b/g/n WiFi Adapter Processor: Intel Core i5-3210M CPU @ 2.50GHz × 4 RAM: 16 GB of RAM Thank you!!!

    Read the article

  • What does a media server need?

    - by DeaDSouL
    I want to buy a new PC to be used as a media server that streams HD movies, music to any wireless device on my network (laptop, desktop, TV, etc.). I was wondering about the PC hardware's specifications that I need to have so that it can work just fine? (It will be wireless) Is there any tutorial showing how it could be done? And the security - how can I secure it? As well as I need it to to host my emails. I mean I have many emails. And sometimes I'm using desktop, sometimes laptop.. so is it possible to make the server store a copy of my emails, attachments, all sent items (whether they were from desktop or laptop)?

    Read the article

  • How to fix additional STA driver installation error on 12.04

    - by nibl
    I have a Broadcom BCM4313 wireless driver. It worked fine under 11.04 and the upgrade to 11.10 also went smoothly. The 12.04 upgrade has broken the wireless connection. I've seen several posts about this and all presume you can activate the STA drivers, but that's where it fails on this machine. The log is in /var/log/jockey.log: WARNING: modinfo for module wl failed: ERROR: modinfo: could not find module wl WARNING: /sys/module/wl/drivers does not exist, cannot rebind wl driver DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted (repeat of last error several times) Any ideas how to proceed?

    Read the article

  • Where are Wireless Profiles stored in Ubuntu

    - by LonnieBest
    Where does Ubuntu store profiles that allow it to remember the credentials to private wireless networks that it has previously authenticate to and used? I just replaced my Uncle's hard drive with a new one and installed Ubuntu 10.04 on it (he had Ubuntu 9.10 on his old hard drive. He is at my house right now, and I want him to be able to access his private wireless network when he gets home. Usually, when I upgrade Ubuntu, I have his /home directory on another partition, so his wireless profile to his own network persists. However, right now, I'm trying to figure out which .folder I need to copy from his /home/user folder on the old hard drive, to the new hard drive, so that he will be able to have wireless Internet when he gets home. Does anyone know with certainty, exactly which folder I need to copy to the new hard drive to achieve this?

    Read the article

  • Wi-Fi Connection Issues.. tried a lot.. pls help

    - by nikvana
    I am posting a question for the first time, do not know coding and am relatively new to ubuntu, but a quick learner. I have an Acer Aspire One D270 notebook that came originally with Windows 7 starter installed. I have removed that and installed Ubuntu 12.04 I have chronic issues with connecting to the wi-fi. I figure it is due to issues with the driver(s) I think this is the driver I have- BCM4313 802.11bgn Wireless Network Adapter (on entering this in the terminal- lshw -C) I also installed the software Windows wireless drivers and it shows currently installed drivers as blank- but when i choose install new drivers, it asks me to select inf file which I do not know where to find. Please help with this, coders. Thanks a ton

    Read the article

  • Two keyboards - one qwerty one dvorak. Can windows use both simultaneously?

    - by Alain
    Similar to this question: Is it possible to use multi keyboards with multi keyboard layouts simultaneously? - I have two keyboards plugged in simultaneously. Both are querty keyboards, but I've rearranged the keys on one to be a dvorak layout. I'd like to find some way to configure windows (XP) such that while both keyboards are plugged in, typing on each results in it's respective layout. I'd prefer if there was someway to have the system automatically use the desired layout based on which USB keyboard it is receiving input from. If no such solution is possible, I would settle for a fast way of switching between US English and US English Dvorak languages so that in a pinch I can easily go from one to the other. Thanks.

    Read the article

  • Concurrent wireless and wired network

    - by Stew Megaw
    Hi, I am concerned with maintaining a wireless and wired network connection on my laptop. Basically I can change the metric on each interface so that Windows prefers one connection over the other. I am wondering is following scenario possible.... Some applications uses the wireless while other applications use the wired... I want Internet Explorer (only) to use the wireless connection while Outlook and everything else uses the wired connection. Perhaps adding some lines to the routing table might work? - Adding the ip addresses of websites I want to view via the wireless connection? Many Thanks in advance for any replies!

    Read the article

  • Wifi worked after reinstalling the driver, but why did it stopped working in the first place?

    - by Ankit
    I was having an issue with connecting to my wifi router since yesterday; could see the router in the wireless networks available but the router was not authenticating my password. I tried unblocking the hardware switches though non was blocked. Finally on discussing with the ISP i gave a re-installation of the wireless driver a try; and to my surprise that worked.(I was assuming faulty wifi router). So as per the subject of the question; I am very curious to know what actually happened that prevented me to connect to my wifi. Any logs that I could see to confirm the cause of this suspicious activity.

    Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >