Search Results

Search found 21436 results on 858 pages for 'imaging and process manag'.

Page 510/858 | < Previous Page | 506 507 508 509 510 511 512 513 514 515 516 517  | Next Page >

• iMac boot from linux partition on external drive

  - by user74757

  I have the following "setup:" iMac (no internal drive/dead) --------- (Firewire) ------- [[MAC OS X]] | | | | (USB) | | | | [[MISC STORAGE PARTITION] [MISC STORAGE PARTITION] [EXT2 UBUNTU PARTITION]] I routinely use the firewire drive to boot MAC OS X. However, I would like to boot from the linux partition of the USB drive. This linux partition had linux installed on it from a live cd, and during that process, I told the installer to install GRUB on the usb drive (which happened to be /dev/sdd). My question is, how do I get this disk to show up during the iMac option-boot? Currently, only the firewire MAC OS X option shows up. I have read about rEFIT, but that appears to install it to the Mac OS X disk (would that still work?)... Also mentioned was installing rEFIT to the internal EFI system partition, but I don't know if that is wise.

  Read the article

• Filtering Client IP from Access Log for Urchin

  - by Ram Prasad

  I have some apache logs to process, and since the webserver behind two levels of reverse proxies, I am getting two IPs in the X-Forwarded-For header.. for example: 208.34.234.55, 127.0.0.1 - - [29/Oct/2009:21:38:13 -0500] "GET /monkey.html HTTP/1.0" 200 20845 0 0 "http://www.monkey.com/" "Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.0.15) Gecko/2009101601 Firefox/3.0.15 (.NET CLR 3.5.30729)" Now, how do I filter this in Urchin (or remove this in Apache logging) so, 127.0.0.1 is removed from processing. Currently urchin is not able to recognize the multuple IP address so it does not log the remote IP

  Read the article

• Squid proxy server not forwarding traffic

  - by DilbertDave

  I'm trying to set up a web filtering system (dans guardian) on my home network but am failing at the first hurdle - configuring the Squid Proxy server. No matter what I do I cannot seem to configure it properly and I just receive the 'Requested URL could not be received' error page. If I remove the proxy setting on the browser everything works normally. Ultimately I want to run this on something like a Raspberry Pi but at the moment I'm testing with a virtual machine (although efforts with a netbook were equally unsuccessful). The VM has a clean installation of Linux Mint 15 and I've installed squid via apt-get. I've followed numerous walkthroughs but this on (https://help.ubuntu.com/lts/serverguide/squid.html) pretty much sums up the process I've been taking. I'm obviously missing something but cannot figure it out - any assistance appreciated.

  Read the article

• Code execution time out occationally

  - by Athul k Surendran

  I am working on an e-commerce website. There is a case where I need to fetch the whole data in database through third-party API and send it to an indexing engine. This third-party API has many functions like getproducts, getproductprice, etc., and each of that functions will return the data in XML format. From there I will take charge, I will use various API calls and will handle the XML data with XSLT. And will write to a CSV file. This file will be uploaded to an Indexing engine. Right now I have details of 8000 products to feed the engine, and almost all time the this process takes about 15 min to complete, and sometimes fails. I can't find a better solution for this. I am thinking about handling the XML data in C# itself and get rid of XSLT. As I think, XSLT is far slower than C#. Is it a good Idea? Or what else I can do to solve this issue?

  Read the article

• Tried to install some software, it says some packages are damaged, cannot fix them

  - by lempira

  So, I go to the Ubuntu Software Center, as soon as it opens, a window pops up with the following text: "Items cannot be installed or removed until the package catalog is repaired. Do you want to repair it now?" Then I click the "Repair" button, then a new window pops up with the following text: "Package operation failed. The installation or removal of a software package failed." Then I click on the "Details" button, which returns me the following text: installArchives() failed: Can't exec "locale": No such file or directory at /usr/share/perl5/Debconf/Encoding.pm line 16. Use of uninitialized value $Debconf::Encoding::charmap in scalar chomp at /usr/share/perl5/Debconf/Encoding.pm line 17. Preconfiguring packages ... Can't exec "locale": No such file or directory at /usr/share/perl5/Debconf/Encoding.pm line 16. Use of uninitialized value $Debconf::Encoding::charmap in scalar chomp at /usr/share/perl5/Debconf/Encoding.pm line 17. Preconfiguring packages ... Can't exec "locale": No such file or directory at /usr/share/perl5/Debconf/Encoding.pm line 16. Use of uninitialized value $Debconf::Encoding::charmap in scalar chomp at /usr/share/perl5/Debconf/Encoding.pm line 17. Preconfiguring packages ... dpkg: warning: 'ldconfig' not found in PATH or not executable. dpkg: error: 1 expected program not found in PATH or not executable. Note: root's PATH should usually contain /usr/local/sbin, /usr/sbin and /sbin. Error in function: SystemError: E:Sub-process /usr/bin/dpkg returned an error code (2) dpkg: warning: 'ldconfig' not found in PATH or not executable. dpkg: error: 1 expected program not found in PATH or not executable. Note: root's PATH should usually contain /usr/local/sbin, /usr/sbin and /sbin. What should I do?

  Read the article

• NTFS write speed really slow (<15MB/s)

  - by Zulakis

  I got a new Seagate 4TB harddrive formatted with ntfs using parted /dev/sda > mklabel gpt > mkpart pri 1 -1 mkfs.ntfs /dev/sda1 When copying files or testing writespeed with dd, the max writespeed I can get is about 12MB/s. The harddrive should be capable of atleast 100MB/s. top shows high cpu usage for the mount.ntfs process. The system has a AMD dualcore. This is the output of parted /dev/sda unit s print: Model: ATA ST4000DM000-1F21 (scsi) Disk /dev/sda: 7814037168s Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 2048s 7814035455s 7814033408s pri The used kernel is 3.5.0-23-generic. The ntfs-3g versions I tried are ntfs-3g 2012.1.15AR.1 (ubuntu 12.04 default) and the newest version ntfs-3g 2013.1.13AR.2. When formatted with ext4 I get good write speeds with about 140MB/s. How can I fix the writespeed?

  Read the article

• What kind of SSL certificate do I need?

  - by Christoffer

  Hi, I want to install HTTPS on my server and I wonder what kind of certificate I will need and where I can buy it. The site is a web application that demands high security by it's users since they store sensitive business data. I am also integrating a third party payment gateway into the register process of the site and need a secure way to send credit card data one way. I do not intend to store this data in our own database. So, what do I need? And also, how do I install it on Ubuntu Server 9.10 / Apache2 ? Cheers! Christoffer

  Read the article

• Why does my fan run so hard on my Dell XPS 15z?

  - by Kilhoffer

  I recently bought a Dell XPS 15z. It came with Windows 7 Home Premium, but I really wanted to try out Ubuntu on it. I ran the Windows installer and was surprised how smooth the process was. Within 10 minutes, I had a dual boot setup with Ubuntu 11.10. It boots into Ubuntu just fine and everything seems to work. I've read a lot about problems with touchpad and wireless, but honestly, I've had none of those issues. The only thing that's really bothering me is the fan constantly runs fast. Under Windows, it rarely ever came on and when it did, it wasnt spinning that fast. What could be going on under Ubuntu that would cause this? I want to get that under control because I want to use Ubuntu as my primary OS and screw Windows. Any help would be much appreciated! Note: I've read that others have set acpi=false, but I have not made any changes to the default installation. Should I make that change?

  Read the article

• ADF & Fusion Development Webcast–December 11th 2012

  - by JuergenKress

  Get up to date and learn everything you wanted to know about Oracle ADF & Fusion Development plus live Q&A chats with Oracle technical staff. Oracle Application Development Framework (ADF) is the standards based, strategic framework for Oracle Fusion Applications and Oracle Fusion Middleware. Oracle ADF's integration with the Oracle SOA Suite, Oracle WebCenter and Oracle BI creates a complete productive development platform for your custom applications. Join us at this FREE virtual event and learn the latest in Fusion Development including: Is Oracle ADF development faster and simpler than Forms, Apex or .Net? Mobile Application Development with ADF Mobile Oracle ADF development with Eclipse Oracle WebCenter Portal and ADF Development Application Lifecycle Management with ADF Building Process Centric Applications with ADF and BPM Oracle Business Intelligence and ADF Integration Live Q&A chats with Oracle technical staff Developer lead, manager or architect – this event has something for everyone. Don't miss this opportunity. For details and registration please click here. View Session Abstracts We look forward to welcoming you at this free event! December 11th, 2012 9:00 – 13:00 GMT & 10:00 – 14:00 CET & 12:00 – 16:00 AST & 13:00 – 17:00 MSK & 14:30 – 18:30 IST WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. BlogTwitterLinkedInMixForumWiki Technorati Tags: ADF,ADF training,Fusion Developer day,webcast,WebLogic Specialization,WebLogic Community,Oracle,OPN,Jürgen Kress

  Read the article

• Photo transfer problems from camera

  - by warkior

  We have a digital camera (Cannon SX130 IS) which we often connect to the Ubuntu 12.10 desktop via USB in order to download the images. In past flavours of Linux (Mint 12 was most recent) it worked fine, however since upgrading to Ubuntu 12.10, the process fails after downloading a small number of the images. I can view the images which will be transferred in the preview window, and I can browse the camera file system to download the images manually, but if I just drag/drop the images over from camera to desktop, it freezes after 5-6 are copied over. I've been able to get around the problem by only copying 3-4 at a time, but when you have 100+ images to transfer, that gets really frustrating. Any advice on where I could start looking for answers, or how I could diagnose the source of the problem further? We have also had some issues with WireLess USB mice though it may not be related. I'm hoping my USB controller in the computer isn't dying... it's not that old. Also, it seems to work much better under Windows.

  Read the article

• Server suddenly running out of entropy

  - by Creshal

  Since a reboot yesterday, one of our virtual servers (Debian Lenny, virtualized with Xen) is constantly running out of entropy, leading to timeouts etc. when trying to connect over SSH / TLS-enabled protocols. Is there any way to check which process(es) is(/are) eating up all the entropy? Edit: What I tried: Adding additional entropy sources: time_entropyd, rng-tools feeding urandom back into random, pseudorandom file accesses – netted about 1 MiB additional entropy per second, problems still persisted Checking for unusual activity via lsof, netstat and tcpdump – nothing. No noticeable load or anything Stopping daemons, restarting permanent sessions, rebooting the entire VM – no change in behaviour What in the end worked: Waiting. Since about yesterday noon, there are no connection problems anymore. Entropy is still somewhat low (128 Bytes peak), but TLS/SSH sessions have no noticeable delay anymore. I'm slowly switching our clients back to TLS (all five of them!), but I don't expect any change in behavior now.

  Read the article

• Problem identifying which page/page/function locks whole IIS server

  - by fnovak

  Hello, I have problem identifying which page/page/function locks whole IIS server. Out of the blue whole w3wp.exe jumps to CPU 90-98% usage. I have created 3 different application pools to see which w3wp.exe service locks the processor but I am unable to find out this information. I can only see that 2 of 3 services have 0-5% usage and one is jumping around 90-98% after some while. I think some process/function/redirect/sql is doing this but I would like to eliminate it. So far I am not even able to find the source of the problem. On my local development machine with VS2010 everything works like charm and I am unable to replicate problem. The server is windows 2k3 web server, sql server 2k5 and .net 4.0 Thank you for your help, links or any information on this issue. Fero

  Read the article

• Translating Documents from a Foreign Language into English on my Computer?

  - by Simon

  I am aware that websites can be translated from many languages into English thanks to Google Translate. If I receive documentation via email that is in a language other than English, how straight forward is it to translate into English on my PC or Apple Mac? (indeed is Google Translate involved or is it strictly for websites) Similarly if I receive documentation via the normal postal mail service (termed "snail mail" if I'm correct) which needs to be translated into English, what steps need to be taken for this documentation to be translated effectively & quickly on my PC or Apple Mac (I am aware of the term Optical Character Recognition (OCR) software, and is this costly, or do free alternatives exist to carry out the translation process solely online? ).

  Read the article

• I'm using a compatible active DisplayPort to DVI adapter with EyeFinity, why does my monitor still flicker?

  - by Christopher Galpin

  I specifically chose an active DisplayPort <- DVI adapter for use with EyeFinity right out of my graphic card vendor's list of confirmed compatible adapters. Yet the screen fails horribly, it blinks on and off constantly, sometimes the graphics go screwy and the appropriate resolutions won't be available. Sometimes the resolution will be available but I'll discover it's only with interlaced refresh rates and bounces up and down. I have to switch the resolution back and forth, again and again, to get it to work correctly, and then it fails again and the process must be repeated the moment the monitor is turned off or I reboot. It's maddening. What is wrong? Is my GFX card supplying insufficient voltage? (Firmware tweaks allegedly help some people, but my card's isn't modifiable.) Could the adapter be defective? Is it not "active" enough for my card and I need an expensive powered adapter? Is this endemic to DisplayPort in general?

  Read the article

• Which built-in account is used for Anonymous Authentication in IIS 7?

  - by smwikipedia

  We know that Microsoft IIS 7.0 offer a slew of authentication methods such as Anonymous Authentication, Form Based Authentication, Digest Authentication, etc. I read from Professional IIS 7 published by Wrox that: When we use Anonymous Authentication, the end-user does not supply credentials, effectively mak- ing an anonymous request. IIS 7.0 impersonates a fixed user account when attempting to process the request (for example, to read the file off the hard disk). So, what is the fixed user account impersonated by IIS? Where can I see it? If I don't know what this account is, how could I assign proper permissions for the clients who are authenticated as anonymous users? Thanks.

  Read the article

• Access Denied on LAN IIS Access via Integrated Authentication

  - by Pharao2k

  I have an IIS 7.5 (Win2k8R2) Webserver, which publishes an UNC Share (on a Fileserver) with restricted access. The AppPool Identity is a Domain User-Account with read access to mentioned UNC path. Authentication modes are set to Anonymous and Integration Authentication. When I access the path via localhost from the Webserver itself, it works, but if I try the Hostname or IP from either the Webserver or a Client, I get three authentication prompts (does not accept my credentials) and a 401.3 Unauthorized error message (but it states that I am logged in as my normal credentials which definitely have access rights to the UNC path and its files). Security Zone is set to Local Intranet. Sysiniternals Process Monitor lists CreateFile operations on the UNC path (and other existing files in it) with Access Denied and Impersonating on the correct credentials. I don't understand why it is not working, it seems to use the correct credentials on every step on the way but fails with is operations.

  Read the article

• Approach to retrieve files from server

  - by Aerus

  I'm in the process of making a Java application with a corresponding update application. At any given time the user may want to update the application and the updater will ask for a list of files of the latest release. Based on this list, the updater can determine which files need to be downloaded to complete the update. I now have 2 approaches to solve this, but i would like to know what approach will put the least stress on my application and server. I could send a list of files i want to download to my server and the server zips the files and simply returns this compressed file to the application. The updater sents a request for each seperate file to the server, which simply returns the file The application will be used mainly in Belgium and The Netherlands and connections/bandwidth tend to be pretty decent in here. The average size of a single file should be around 100Kb and at most 1Mb. I expect an update to have anywhere between 10 to 50 new files. I expect at most 100 persons/day to update the application, i.e. in the week when a new version is released. I hope this is enough information to sketch my problem and any advice is welcome. If there is another common way to tackle this, i'd be glad to hear it.

  Read the article

• Black login screen Ubuntu 12.04 if WGA cable pluged in on reboot

  - by Sulliwane

  I'm using Ubuntu 12.04.1, 64 bits, installed on a Z77 Pro4 (ASrock motherboard), crucial M4 SSD drive (sata 3), and intel i5 3570k (ivy bridge). I have this annoying problem : When I startup the computer, I get a CLI login prompt : At this moment, if I press enter, i get the usual CLI login prompt. If not, here is what I get : From now, if I login using CLI, i identify the lightdm processus, kill and start it : #ps -A | grep lightdm #sudo kill -9 1273 #sudo lightdm and miracle, these commands bring back the gui login screen. BUT It's very annoying as I have to repeat these steps at every boot, and the people using this desktop are not familiar with linux at all! So I tried to figure out the cause and here is what I found : If, when I shutdown the computer, the WGA cable is not pluged in, then Ubuntu will boot on GUI login screen without a glitch! But If the WGA cable is pluged in when shuting down, I will get CLI login prompt... Note 1: I installed linux kernel 3.4, but it hasn't solve the problem. Note 2: Is it linked to the new HD 4000 integrated graphic processor ? Note 3: If i boot on an USB stick (Ubuntu 12.04), NO problems ! Note 4: If booting on the SSD, when clicking "shutdown" button, the shutdown process never ends up (logout screen keep displaying and fans are still rolling). But if booting on USB stick, the shutdown action runs properly.

  Read the article

• What is the computer "doing" when it is running slow and task manager is not showing any CPU activity?

  - by Joakim Tall

  Typical example is when shutting down a memoryintensive application. It can take quite a while before the computer gets back up to speed. Is there some inherent cost in releasing memory? Or is it throttled by some kind of harddrive activity, and if so is there any good way to track that? I usually bring up task manager when a computer is running slow, and usually sorting by cpu activity can show what process is causing the problem, but sometimes there is no activity showing. And yes I "show processes from all users", I have been wondering this since the days win2k :)

  Read the article

• Ubuntu hangs on boot when NFS-mounting entries in /etc/fstab, but they mount cleanly otherwise

  - by lorin

  I'm managing several Ubuntu 9.10 servers that NFS mount several folders (including /home). I'd like these folders to be mounted at boot time. I would like to have several entries in my /etc/fstab to accomplish this, e.g. 192.168.1.100:/home /home nfs rw 0 0 192.168.1.100:/usr/ansys_inc /ansys_inc nfs ro 0 0 Unfortunately, with this configuration, the servers usually (although not always) hang during the bootup sequence when trying to do the NFS mount. if I comment out these fstab entries, reboot the machine, uncomment them and mount them manually using the shell, the folders mount cleanly. I'm not sure how to go about debugging this problem. It seems like it has something to do with the boot sequence, that some relevant process hasn't been started by the time the OS tries to mount the folders.

  Read the article

• StyleCop Custom Rules

  - by Aligned

  There are several blogs on how to do this (http://scottwhite.blogspot.com/2008/11/creating-custom-stylecop-rules-in-c.html, etc). I’ve found a few useful things to point out: Debugging is difficult, but here are the steps (thanks to Tintin’s answer). “One way: 1) Delete your custom rules 2) Open Visual Studio (for dev), open your custom rule solution 3) Build & Deploy custom rules (a PostBuild action to copy the rules into the StyleCop folder is handy) 4) Open Visual Studio (for test) 5) Use VS (dev) and Attach to process devenv.exe (the test VS instance), set breakpoints in the rules you want to debug 6) Use VS’ (test) and right-click on project, Run StyleCop 7) Debug” ~ it worked once, now I’m having problems getting it to work again ~ I also get the message “Cannot evaluate expression because the code of the current method is optimized.” when I try to look at properties. Looking at the source code of the StyleCop.CSharp.Rules.dll that comes with the install. I used JustDecompile from Telerik. Create one xml file and name it the same as the one cs file (CodingGuildelineRules.cs and CodingGuidelinRules.xml) Deploy: 1. Build in Visual Studio 2. Close Visual Studio (Style cop is running so you can’t override your dll without closing) 3. Copy the dll from the bin to the C: \Program Files (x86)\StyleCop 4.7\ 4. Open the settings file or re-open Visual Studio

  Read the article

• What are best monitoring tool customizable for cluster / distributed system?

  - by Adil

  I am working on a system having multiple servers. I am interested in monitoring some server specific data like CPU/memory usage, disk/filesystem usage, network traffic, system load etc. and some other my process specific data. What are available open source that can serve my purpose? If it provides to customize the parameter to be monitored and monitor your own data by creating plugin / agent. Any suggestions? I heard of Nagios, Zabbix and Pandora but not sure if they provide such interface.

  Read the article

• How can I update Firefox add-ons automatically?

  - by Maelstrom

  Similar to this question, is it possible to update installed plugins via the command line? I'm running YSlow with beacon reporting as a nightly cron job under OSX: /Applications/Firefox.app/Contents/MacOS/firefox-bin -no-remote -P YSlow http://www.example.com/ & PID=$! sleep 300 kill $PID This dumps FF into the background and grabs the PID, waits 300 seconds (for the page to load) then kills it. If there is an update pending, the browser "hangs" waiting for a confirmation. If I do click on the "install updates" link, everything works and then Firefox launches a new process - the $! returned by the shell is no longer valid. Can I update a plugin from the command line without confirmation? Can I curl the XPI into a file and install it without confirmation?

  Read the article

• Entity system in Lua, communication with C++ and level editor. Need advice.

  - by Notbad

  Hi!, I know this is a really difficult subject. I have been reading a lot this days about Entity systems, etc... And now I'm ready to ask some questions (if you don't mind answering them) because I'm really messed. First of all, I have a 2D basic editor written in Qt, and I'm in the process of adding entitiy edition. I want the editor to be able to receive RTTI information from entities to change properties, create some logic being able to link published events to published actions (Ex:A level activate event throws a door open action), etc... Because all of this I guess my entity system should be written in scripting, in my case Lua. In the other hand I want to use a component based design for my entities, and here starts my questions: 1) Should I define my componentes en C++? If I do this en C++ won't I loose all the RTTI information I want for my editor?. In the other hand, I use box2d for physics, if I define all my components in script won't it be a lot of work to expose third party libs to lua? 2) Where should I place the messa system for my game engine? Lua? C++?. I'm tempted to just have C++ object to behave as servers, offering services to lua business logic. Things like physics system, rendering system, input system, World class, etc... And for all the other things, lua. Creation/Composition of entities based on components, game logic, etc... Could anyone give any insight on how to accomplish this? And what aproach is better?. Thanks in advance, HexDump.

  Read the article

• tunneling x11vnc through ssh on a non standard port to ubuntu computer tightvnc

  - by user72372

  I have been stuck with setting up my virtual desktop on my ubuntu laptop. I am running ubuntu to ubuntu with x11vnc I start the process on my laptop as follows: " ssh -L5904:localhost:5900 -p Port remoteuser@remoteip." That command works, then I start x11vnc server, "x11vnc -noncache -once -shared -rfbauth ~/.vnc/passwd." This command works and starts connection. Then I open another window on my laptop and type, export VNC_VIA_CMD='/usr/bin/ssh -2 -c aes128-cbc -x -p Port -l User -f -: %L:%H:%R %G sleep 20' (not sure if works). then I type, vncviewer -endcodings Tight -depth 8 -quality 1 -via IPofremotemachine -u remoteuser localhost:01. The first time it work but from now on it just gives me the vncviewer -help screen everytime. I type in the password for my remote machine and then shows -help screen for vncviewer. I think the problem is with Tightvnc viewer but don't know what. Please help. I got some info on www.vanemery.com/Linux/VNC/vnc-over-ssh.html?.

  Read the article

< Previous Page | 506 507 508 509 510 511 512 513 514 515 516 517  | Next Page >