Search Results

Search found 27336 results on 1094 pages for 'network state'.

Page 510/1094 | < Previous Page | 506 507 508 509 510 511 512 513 514 515 516 517  | Next Page >

  • Google Chrome doesn't want to access Facebook

    - by Pieter van Niekerk
    I have been experiencing a bit of a problem with Chrome over the last couple of days where it doesn't want to access Facebook. When I open Chrome it works fine for a while and then if I were to refresh the page it would give me the Chrome 'This webpage is not available' message. This webpage is not available Google Chrome could not load the webpage because www.facebook.com took too long to respond. The website may be down, or you may be experiencing issues with your Internet connection. Here are some suggestions: Reload this webpage later. Check your Internet connection. Restart any router, modem, or other network devices you may be using. Add Google Chrome as a permitted program in your firewall's or antivirus software's settings. If it is already a permitted program, try deleting it from the list of permitted programs and adding it again. If you use a proxy server, check your proxy settings or contact your network administrator to make sure the proxy server is working. If you don't believe you should be using a proxy server, adjust your proxy settings: Go to the wrench menu Options Under the Hood Change proxy settings... LAN Settings and deselect the "Use a proxy server for your LAN" checkbox. This problem only persists when using the proxy and doesn't occur at all when not on the proxy. I have also tried different browsers (IE9 and Firefox 9.01) but it doesn't occur in any of them. This problem goes away for a while when I restart Chrome, only to happen again a couple of minutes later. I have tried deleting the cookies for Facebook without restarting Chrome, but to no avail. I am using Windows7 with Chrome 17

    Read the article

  • Bridging Wireless and Wired Interfaces in Linux

    - by The Daemons Advocate
    My network setup is something like: Wireless Router <---> Netbook <---> Ubuntu Desktop ...or, more verbosely (with interfaces): Wireless Router <--(wireless)--> (eth2) Ubuntu Netbook Ubuntu Netbook (eth0) <---(wired)----> (eth0) Ubuntu Desktop In a perfect world, I'd have the desktop wired, but weird circumstances combined with my wanting to understand more about networking in linux make me want to figure out how to bridge these two devices. A bit of googling has given me this example using bridge-utils, and here's how I'm (failing) to setup the bridge (on the netbook): sudo -i ifconfig eth0 0.0.0.0 ifconfig eth2 0.0.0.0 brctl addbr bridget brctl addif bridget eth0 brctl addif bridget eth2 ifconfig bridget up ...then, trying to make sure that the netbook can still get on the internets... route add default gateway 192.168.2.1 dhclient bridget What happens after this is that the dhclient command above (netbook) doesn't get served an IP, and the Desktop, if I run dhclient, it doesn't get served an IP. Some weird considerations might be that I'm running the Network Manager Applet that comes with Ubuntu. While I'm sure I can get a command line wireless configuration setup, it's a bit complex. Can someone give me a shout as to where I'm going wrong? I'd also like to note another related question titled 'Bridging my laptop’s wireless and wired adaptors', however the setup is different to mine.

    Read the article

  • Domain workstation acting up and I can't track it down.

    - by DevNULL
    I have a developer with a Windows XP (SP2) 64 bit machine. If the machine is left on overnight (or any period of time longer than 5-6 hours) it takes 2-3 minutes to open any local drive and his network drives are no longer accessible. Here's what the system logs report... Any Help BTW: The problem just started a week ago and nothing has changed on the domain controller / AD or his machine. --- ERROR 1 Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 5719 Date: 6/8/2010 Time: 9:17:26 AM User: N/A Computer: BFC1 Description: This computer was not able to set up a secure session with a domain controller in domain UR due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. ADDITIONAL INFO If this computer is a domain controller for the specified domain, it sets up the secure session to the primary domain controller emulator in the specified domain. Otherwise, this computer sets up the secure session to any domain controller in the specified domain. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 5e 00 00 c0 ^..A --- ERROR 2 The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID {555F3418-D99E-4E51-800A-6E89CFD8B1D7} to the user NT AUTHORITY\LOCAL SERVICE SID (S-1-5-19). This security permission can be modified using the Component Services administrative tool. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. --- ERROR 3 Event Type: Error Event Source: RemoteAccess Event Category: None Event ID: 20106 Date: 6/8/2010 Time: 10:12:18 AM User: N/A Computer: BFC1 Description: Unable to add the interface {E76F0A78-7A0B-4EBB-A081-BA3BD452FC4C} with the Router Manager for the IP protocol. The following error occurred: Cannot complete this function. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: eb 03 00 00 e...

    Read the article

  • Why is Windows 7 slow resume from suspend?

    - by John McC
    I have Windows 7 on an HP Mini 5101. It is can be very slow to resume from suspend (not hibernate) state. The time from power on to the login prompt varies from say 10 sec to over a minute. This machine mainly gets used for sofa surfing so usually only Firefox and gtalk are running. Any suggestions on how to achieve Mac-like start-up or suggestions on how to track down the problem appreciated.

    Read the article

  • Set up tunnel to HE.net and now only ipv6.google.com works, but other sites ping fine.

    - by AndrejaKo
    I'm setting up IPv6 using my router which is running OpenWRT, version Backfire 10.03.1-rc4. I made a tunnel using Hurricane Electric's tunnel broker and set it up on the router and I'm using RADVD to hand out IPv6 addresses. My problem is that on computers on the network, I can only access ipv6.google.com using a browser, but other sites seem to be loading forever and won't open in any browser. I can ping and traceroute to them fine, but can't open them with a browser. I can open any site normally with a browser from the router. Stopping firewall service on the router doesn't help, so it's probably not a firewall issue. All AAAA records resolve fine, so it's probably not a DNS issue. Computers on the network get their IPv6 addresses fine, so it's probably not a radvd issue. Similar setup worked fine for SixXs, but I'm having problems with my PoP there, so I decided to move to HE. Here are some traceroutes: From a client computer: Tracing route to ipv6.he.net [2001:470:0:64::2] over a maximum of 30 hops: 1 <1 ms 1 ms 1 ms 2001:470:1f0b:de5::1 2 62 ms 63 ms 62 ms andrejako-1.tunnel.tserv6.fra1.ipv6.he.net [2001:470:1f0a:de5::1] 3 60 ms 60 ms 63 ms gige-g2-4.core1.fra1.he.net [2001:470:0:69::1] 4 63 ms 68 ms 68 ms 10gigabitethernet1-4.core1.ams1.he.net [2001:470:0:47::1] 5 84 ms 74 ms 76 ms 10gigabitethernet1-4.core1.lon1.he.net [2001:470:0:3f::1] 6 146 ms 147 ms 151 ms 10gigabitethernet4-4.core1.nyc4.he.net [2001:470:0:128::1] 7 200 ms 198 ms 202 ms 10gigabitethernet5-3.core1.lax1.he.net [2001:470:0:10e::1] 8 219 ms * 210 ms 10gigabitethernet2-2.core1.fmt2.he.net [2001:470:0:18d::1] 9 221 ms 338 ms 209 ms gige-g4-18.core1.fmt1.he.net [2001:470:0:2d::1] 10 206 ms 210 ms 207 ms ipv6.he.net [2001:470:0:64::2] Trace complete. and another from a cliet computer Tracing route to whatismyipv6.com [2001:4870:a24f:2::90] over a maximum of 30 hops: 1 7 ms 1 ms 1 ms 2001:470:1f0b:de5::1 2 69 ms 70 ms 63 ms AndrejaKo-1.tunnel.tserv6.fra1.ipv6.he.net [2001:470:1f0a:de5::1] 3 57 ms 65 ms 58 ms gige-g2-4.core1.fra1.he.net [2001:470:0:69::1] 4 73 ms 74 ms 75 ms 10gigabitethernet1-4.core1.ams1.he.net [2001:470:0:47::1] 5 71 ms 74 ms 76 ms 10gigabitethernet1-4.core1.lon1.he.net [2001:470:0:3f::1] 6 141 ms 149 ms 148 ms 10gigabitethernet2-3.core1.nyc4.he.net [2001:470:0:3e::1] 7 141 ms 147 ms 143 ms 10gigabitethernet1-2.core1.nyc1.he.net [2001:470:0:37::2] 8 144 ms 145 ms 142 ms 2001:504:1::a500:4323:1 9 226 ms 225 ms 218 ms 2001:4870:a240::2 10 220 ms 224 ms 219 ms 2001:4870:a240::2 11 219 ms 218 ms 220 ms 2001:4870:a24f::2 12 221 ms 222 ms 220 ms www.whatismyipv6.com [2001:4870:a24f:2::90] Trace complete. Here's some firewall info on the router: root@OpenWrt:/# iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 syn_flood tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 input_rule all -- 0.0.0.0/0 0.0.0.0/0 input all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP) target prot opt source destination zone_wan_MSSFIX all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED forwarding_rule all -- 0.0.0.0/0 0.0.0.0/0 forward all -- 0.0.0.0/0 0.0.0.0/0 reject all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 output_rule all -- 0.0.0.0/0 0.0.0.0/0 output all -- 0.0.0.0/0 0.0.0.0/0 Chain forward (1 references) target prot opt source destination zone_lan_forward all -- 0.0.0.0/0 0.0.0.0/0 zone_wan_forward all -- 0.0.0.0/0 0.0.0.0/0 zone_wan_forward all -- 0.0.0.0/0 0.0.0.0/0 Chain forwarding_lan (1 references) target prot opt source destination Chain forwarding_rule (1 references) target prot opt source destination nat_reflection_fwd all -- 0.0.0.0/0 0.0.0.0/0 Chain forwarding_wan (1 references) target prot opt source destination Chain input (1 references) target prot opt source destination zone_lan all -- 0.0.0.0/0 0.0.0.0/0 zone_wan all -- 0.0.0.0/0 0.0.0.0/0 zone_wan all -- 0.0.0.0/0 0.0.0.0/0 Chain input_lan (1 references) target prot opt source destination Chain input_rule (1 references) target prot opt source destination Chain input_wan (1 references) target prot opt source destination Chain nat_reflection_fwd (1 references) target prot opt source destination ACCEPT tcp -- 192.168.1.0/24 192.168.1.2 tcp dpt:80 Chain output (1 references) target prot opt source destination zone_lan_ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 zone_wan_ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 Chain output_rule (1 references) target prot opt source destination Chain reject (7 references) target prot opt source destination REJECT tcp -- 0.0.0.0/0 0.0.0.0/0 reject-with tcp-reset REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain syn_flood (1 references) target prot opt source destination RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 25/sec burst 50 DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_lan (1 references) target prot opt source destination input_lan all -- 0.0.0.0/0 0.0.0.0/0 zone_lan_ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_lan_ACCEPT (2 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_lan_DROP (0 references) target prot opt source destination DROP all -- 0.0.0.0/0 0.0.0.0/0 DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_lan_MSSFIX (0 references) target prot opt source destination TCPMSS tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU Chain zone_lan_REJECT (1 references) target prot opt source destination reject all -- 0.0.0.0/0 0.0.0.0/0 reject all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_lan_forward (1 references) target prot opt source destination zone_wan_ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 forwarding_lan all -- 0.0.0.0/0 0.0.0.0/0 zone_lan_REJECT all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_wan (2 references) target prot opt source destination ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:68 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ACCEPT 41 -- 0.0.0.0/0 0.0.0.0/0 input_wan all -- 0.0.0.0/0 0.0.0.0/0 zone_wan_REJECT all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_wan_ACCEPT (2 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_wan_DROP (0 references) target prot opt source destination DROP all -- 0.0.0.0/0 0.0.0.0/0 DROP all -- 0.0.0.0/0 0.0.0.0/0 DROP all -- 0.0.0.0/0 0.0.0.0/0 DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_wan_MSSFIX (1 references) target prot opt source destination TCPMSS tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU TCPMSS tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU Chain zone_wan_REJECT (2 references) target prot opt source destination reject all -- 0.0.0.0/0 0.0.0.0/0 reject all -- 0.0.0.0/0 0.0.0.0/0 reject all -- 0.0.0.0/0 0.0.0.0/0 reject all -- 0.0.0.0/0 0.0.0.0/0 Chain zone_wan_forward (2 references) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 192.168.1.2 forwarding_wan all -- 0.0.0.0/0 0.0.0.0/0 zone_wan_REJECT all -- 0.0.0.0/0 0.0.0.0/0 Here's some routing info: root@OpenWrt:/# ip -f inet6 route 2001:470:1f0a:de5::/64 via :: dev 6in4-henet proto kernel metric 256 mtu 1280 advmss 1220 hoplimit 0 2001:470:1f0b:de5::/64 dev br-lan proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::/64 dev br-lan proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::/64 dev eth0.1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::/64 dev eth0.2 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::/64 via :: dev 6in4-henet proto kernel metric 256 mtu 1280 advmss 1220 hoplimit 0 default dev 6in4-henet metric 1024 mtu 1280 advmss 1220 hoplimit 0 I have computers running windows 7 SP1 and openSUSE 11.3 and all of them have same problem. I also made a thread about this on HE's forum, but it seems that people there are out of ideas what to do.

    Read the article

  • postmap: fatal: open database /etc/postfix/sasl_passwd.db: Permission denied

    - by James Benders
    Hi, I'm configurint Postfix to use external smtp. For this, I use the following tutorial: http://carlton.oriley.net/blog/?p=31 After following it, I found in the logs that /etc/postfix/sasl_passwd.db couldn't be read. The file didn't exist. I used postmap hash:/etc/postfix/sasl_passwd (http://postfix.state-of-mind.de/patrick.koetter/smtpauth/smtp_auth_mailservers.html) as root, but I get: postmap: fatal: open database /etc/postfix/sasl_passwd.db: Permission denied Why do I get this? Thanks.

    Read the article

  • How do I ensure a process is running, even if it kills itself? (it needs to be restarted then)

    - by le_me
    I'm using linux. I want a process (an irc bot) to run every time I start the computer. But I've got a problem: The network is bad and it disconnects often, so I need to manually restart the bot a few times a day. How do I automate that? Additional information: The bot creates a pid file, called bot.pid The bot reconnects itself, but only a few times. The network is too bad, so the bot kills itself sometimes because it gets no response. What I do currently (aka my approach ;) ) I have a cron job executing startbot.rb every 5 minutes. (The script itself is in the same directory as the bot) The script: #!/usr/bin/ruby require 'fileutils' if File.exists?(File.expand_path('tmp/bot.pid')) @pid = File.read(File.expand_path('tmp/bot.pid')).chomp!.to_i begin raise "ouch" if Process.kill(0, @pid) != 1 rescue puts "Removing abandoned pid file" FileUtils.rm(File.expand_path('tmp/bot.pid')) puts "Starting the bot!" Kernel.exec(File.expand_path('./bot.rb')) else puts "Bot up and running!" end else puts "Starting the bot!" Kernel.exec(File.expand_path('./bot.rb')) end What this does: It checks if the pid file exists, if that's true it checks if kill -s 0 BOT_PID == 1 (if the bot's running) and starts the bot if one of the two checks fail/are not true. My approach seems to be quite dirty so how do I do it better?

    Read the article

  • How do I prevent or override a group policy on Windows 7?

    - by Kevin
    A few months ago my company was purchased by a large corporation. We recently switched our network over to the large corporate network which has more restrictions requirements. One of these is the requirement to use a proxy server for Internet traffic. However, some of our internal servers are not recognized by the corporate DNS, so we need to provide the fully qualified domain name. For W7, we make changes to the Internet Properties for IE8 and Chrome to include our domain name as an exception to the proxy server (e.g., *.foobar.com). The problem is that a group policy that does not include our domain name is continually pushed out to my systems throughout the day. This requires me to make the appropriate changes to the Internet Properties several times a day in order to access our internal servers. Is there a way that I can prevent the group policy from being pushed to my systems or detect when the group policy is pushed and override it? I am an administrator on all of my systems. I do have Firefox installed which is not subject to the same group policy push, but I need to have IE8 and Chrome working.

    Read the article

  • Hyper-v on 2012R2 startup gen1 vm causes the host to freeze up

    - by sputnik
    I've searched a lot to resolve the following issue, but nothing helped me. My problem is, that starting up a first-gen vm locks up the whole host. Only a hard reset helps. Second-gen vm starts and runs perfectly. The freezes happened on 3 different vms. FreeBSD, Ubuntu, Windows Server 2008R2, while Windows 8.1 on second gen config works perfectly. Im using this pc mainly as a workstation. No eventlog errors nor dumps are generated. My system: Windows Server 2012R2 FX-8350, non OC ASRock 870 Extreme R2 (Crappy board imho) 32GB DDR3 1866@1600 (My motherboard, against the "support" for 1866ram won't work with full speed) 120GB SSD 4.5TB Storage space device I dont think that its due to my system, because vmware workstation was running without problems. Did I forget to configure something? Any help is appreciated. P.S: Even deactivating C1E, C6, C&Q didnt work. P.P.S: With no virtual network adapter set, the system still locks up. Creating a first gen vm without any hdds and network and launching works. Attaching a boot dvd causes the host to freeze. The host freezes as the gen1 vm begins to boot, doesn't matter if from dvd or hdd

    Read the article

  • How can I cause Task Scheduler to "fail" if a dialog box returns a certain result?

    - by Roger
    I'm working on a VBScript to do a weekly reboot of all machines on our network. I want to run this script via Task Scheduler. The script runs at 3:00 AM, but there is a small chance that users may still be on the network at that time, and I need to give them the option to terminate the reboot. If they do so, I would like the reboot to occur the next night at 3:00 AM. I've set Task Scheduler up to repeat in this way. So far, so good. The problem is that if the user selects "Cancel" in my script, the Task Scheduler does not see my task as failed, and won't run it again the next night. Any ideas? Can I pass an errorcode to task scheduler or otherwise abort the task via VBScript? My code is below: Option Explicit Dim objShell, intShutdown Dim strShutdown, strAbort ' -r = restart, -t 600 = 10 minutes, -f = force programs to close strShutdown = "shutdown.exe -r -t 600 -f" set objShell = CreateObject("WScript.Shell") objShell.Run strShutdown, 0, false 'go to sleep so message box appears on top WScript.Sleep 100 ' Input Box to abort shutdown intShutdown = (MsgBox("Computer will restart in 10 minutes. Do you want to cancel computer restart?",vbYesNo+vbExclamation+vbApplicationModal,"Cancel Restart")) If intShutdown = vbYes Then ' Abort Shutdown strAbort = "shutdown.exe -a" set objShell = CreateObject("WScript.Shell") objShell.Run strAbort, 0, false End if Wscript.Quit Appreciate any thoughts.

    Read the article

  • Multiple WAN interfaces on SonicWall TZ 100?

    - by Chad Decker
    I'm using a SonicWall TZ 100 with a basic configuration of X0 for the LAN and X1 for the WAN. The WAN uses DHCP to obtain its routable IP address. I want to obtain a second routable IP from my ISP. I'm in luck because my cable company will provide me with an additional dynamic IP for $5/mo. How do I bind this IP to my SonicWall? My additional dynamic IP will not be consecutive to the original one. It won't even be on the same class C. I think what I want to do is to use one of the empty ports/interfaces (X2, X3, or X4), tell that interface to use DHCP, and then add that interface to the WAN "zone". I can't figure out how to do this though. Here's what I've tried so far: (1) I've looked in Network Interfaces. I see X0 and X1 but the other unused interfaces don't show up. I don't see an "Add" button to add the new interfaces. (2) I've looked in Network Zones. I see that X0, X2, X3, X4 are in the LAN zone. I tried to drag X3 into the WAN zone but I can't. Nor does clicking the "Configure" button allow me to move an unused interface from LAN to WAN. (3) I've read the post entitled Splitting up multiple WAN's on Sonicwall. This doesn't seem applicable to me. Any thoughts?

    Read the article

  • Intermittent NFS lockups on Isilon cluster

    - by blackbox222
    We have an Isilon cluster with 8 IQ 12000x nodes which exports storage via several NFS shares for a handful of Linux and Solaris clients. There is a Linux system that has one of these NFS filesystems mounted. I/O to this filesystem is moderately heavy from the Linux system. Every 3-4 weeks (it's not on any kind of discernible schedule, and sometimes is more/less frequent than this), we notice that all activity ceases on this NFS mount (the process hangs, as if the network stopped working so process is stuck in uninterruptible sleep) - 30 minutes later, the share recovers and things continue to work normally. The kernel log from the affected machine is as follows: Dec 3 10:07:29 redacted kernel: [8710020.871993] nfs: server nfs-redacted not responding, still trying Dec 3 10:37:17 redacted kernel: [8711805.966130] nfs: server nfs-redacted OK relevant /etc/fstab line: nfs-redacted:/ifs/nfs/export_data/shared/...redacted... /data nfs defaults 0 0 I've checked to see if there are any scheduled processes e.g. cron jobs, Isilon related functions e.g. snapshots, etc that might be causing these hangups but I can't seem to find anything. I'm also not aware of any network related issues or maintenance that would cause this. All of the lockups last almost exactly 30 minutes per the kernel logs. Perhaps someone has some suggestions I could try? (I considered a soft mount to avoid the problems associated with processes accessing the filesystem hanging; however am wary of the corruption that could result and it would not really solve the underlying issue anyway).

    Read the article

  • Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

    - by Pro Backup
    In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

    Read the article

  • Fixed Resource Monitor Graph Scale in Windows Server 2008 R2

    - by Clever Human
    In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums?

    Read the article

  • What steps should I take to debug this non-starting hvm virtual machine?

    - by Ophidian
    I have a dom0 machine running CentOS 5.4 with all the latest updates using Xen as my hypervisor. I am using Xen in part because this machine was set up prior to KVM being included in RHEL, and in part because KVM's network bridging configuration is not nearly as simple as Xen's. The dom0 machine is headless and I do all of my VM management via virsh from the command line. I have two hvm domU's: A web server running CentOS 5.4 A mail server running Gentoo Both VM's are backed by LV's on the dom0 but do not use LVM in the domU. Both have virtually identical libvirt configurations (differing by expected things like name, UUID, NIC MAC, VNC port, etc). The web server domU (WSdomU hereafter) does not start since applying the most recent kernel update (kernel-xen-2.6.18-164.15.1.el5.x86_64 and kernel-2.6.18-164.15.1.el5.x86_64 for the dom0 and WSdomU respectively). By 'not start' I mean it appears to be running but it does not use an CPU cycles, does not bring up a graphical console, and does not respond on the network. The WSdomU is listed as no state rather than the normal running or blocked in xentop. The mail server domU starts fine and functions normally. Here are the steps I have taken so far that did not solve the problem: Reboot the dom0 to see if things come up on their own Check xen dmesg on dom0 Check xend logs (a cursory viewing did not show anything blatant; specific suggestions of things to look for would be appreciated) Attempted to connect to the WSdomU's graphical (VNC) console from the dom0 Shutdown the mail server domU and attempt to start the WSdomU Check the SELinux labels on backing LV's (they're the same) Set SELinux to permissive and attempt to start the WSdomU Use virsh edit to try tweaking the WSdomU config virsh undefine, reboot, virsh define the WSdomU config dd the WSdomU LV to an .img file, copy it to my Fedora desktop and run it under KVM (works fine) What steps should I take next to debug this? I will edit in any additional configuration's requested in the comments.

    Read the article

  • Can Windows logoff events be tracked?

    - by Massimo
    I'm working on an application to track network user logon/logoff events in an Active Directory domain; the application will work by auditing security logs on domain controllers. Auditing logon events can get somewhat tricky, but it can succesfully be done. My problem: how can I track logoff events? Based on some research I've done, it looks like these events are only logged locally on workstations, but not on DCs; also, the "lastLogoff" attribute exists on AD user objects, but it's not actually used by anyone. This is a very specific question: is something logged on DCs when a user logs off from a domain workstation? To clarify: I'm not intereseted in other auditing mehods, I can't deploy logon/logoff scripts and I can't install anything anywhere; I also know opened and closed network sessions are logged, but this is not what I'm looking for. I need to audit interactive logons and logoffs to domain workstations, and I can do this by only reading domain controllers security logs; reading each workstation's local event logs is out of question. If this can't be done, it's ok; but I need a clear answer on that. Can this be done? If yes, how?

    Read the article

  • Joining Samba to Active Directory with local user authentication

    - by Ansel Pol
    I apologise that this is somewhat incoherent, but hopefully someone will be able to make enough sense of this to understand what I'm trying to achieve and provide pointers. I have a machine with two network interfaces connected to two different networks (one of which it's providing several other services for, such as DNS), running two separate instances of Samba, one bound to each interface. One of the instances is just a workgroup-style setup using share-level authentication, which is all working fine. The problem is that I'm looking to join the other instance to an MS Active Directory domain (provided by MS Windows Small Business Server 2003) to enable a subset of the domain users to access the shares from Windows machines on the other network. The users who need access from the domain environment have accounts (whose names are all-lowercase versions of their domain usernames) on the machine running Samba, but I'm not sure about how to map the UIDs and everything I've read concerns authenticating accounts on that machine against either AD or another LDAP server. To clarify: I only want the credentials for AD users accessing the non-workgroup Samba instance to be authenticated against AD, not the accounts on the machine running Samba. I hope this is sufficiently clear. EDIT: In addition to being able to access the Samba shares from AD, I do also need to be able to access a share on the domain from the machine running Samba but would still like everything non-Samba-related to authenticate locally.

    Read the article

  • Get Internal IP Address From DHCP Hostname

    - by ell
    I would like to try and get an internal ip address of one of the computers on my network. The reason for this is I have a little home server box downstairs but every time I want to SSH into it I have to open my router configuration and go on the DHCP client table and look at the IP address. For example I would like to be able to go ssh ell-sever instead of ssh 192.168.1.105 or whatever it happens to be. My network configuration is like so: Router downstairs that is connected to the Internet and is running a DHCP server My server computer (ell-server) is a headless pc connected to the router via ethernet cable. Running Ubuntu 11.04 Server Edition My laptop upstairs (ell-laptop) that is running Ubuntu 11.10 Desktop Edition connected wirelessly Other (irrelevant) computers - 2 x Windows XP, 1 x Xubuntu - all connected with cables. (It seemed to me the method of connection isn't useful information but I put it in anyway - just in case. If I have missed any information please tell me) Do I have to run a DNS server on one of my computers? If so which one? And does that mean I will have to run a DDNS client on each computer? Thanks in advance, ell.

    Read the article

  • Can't get rsync over sftp to work

    - by Patrik
    I'm trying to set up a backup system from an Ubuntu server to a Synology NAS (DS413j) using rsync and sftp. I have created a user for this that we can call ubuntu-backup. I have a directory in ubuntu-backup home directory called www where the backup will be saved. I have enabled Network Backup in DSM The user ubuntu-backup has full access to it's home directory Here is my rsync config file on the Synology NAS: #motd file = /etc/rsyncd.motd #log file = /var/log/rsyncd.log pid file = /var/run/rsyncd.pid lock file = /var/run/rsync.lock use chroot = no [NetBackup] path = /var/services/NetBackup comment = Network Backup Share uid = root gid = root read only = no list = yes charset = utf-8 auth users = root secrets file = /etc/rsyncd.secrets [ubuntu-backup] path = /volume1/homes/ubuntu-backup/www comment = Ubuntu Backup uid = ubuntu-backup gid = users read only = false auth users = ubuntu-backup secrets file = /etc/rsyncd.secrets The permissions on /volume1/homes/ubuntu-backup/www is ubuntu-backup:users 777 Here is the command i'm running. rsync -aHvhiPb /var/www/ [email protected]:./ The result: sending incremental file list ERROR: module is read only rsync error: syntax or usage error (code 1) at main.c(1034) [Receiver=3.0.9] rsync: connection unexpectedly closed (9 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(605) [sender=3.0.9] If I'm running this: rsync -aHvhiPb /var/www/ [email protected] It looks like its sending files. No errors. But I cant find anything on the NAS.

    Read the article

  • Windows 7 fails to connect to the internet a few minutes after startup

    - by SageTheGreat
    Problem Earlier today, when I turned on my desktop computer, my internet connection works fine. Cryptocurrency miners connecting and hashing as usual and I can browse websites. But after a few minutes, my miner fails indicating that there is something wrong with my internet connection. Tried refreshing my browser and is stuck at "resolving host", and then presented me an error. After that, i can't browse sites anymore. But the weird thing is that the network icon in Windows 7 shows no signs of problems. Solutions Made Restarted my computer without doing anything: Problem persists. Tried using the network troubleshooter of windows: Reported no problems Stopped bonjour still no progress. Loaded windows using Last good config: still no progress. Restarted Modem: No change. Current Status I currently did a system restore to my system to a point before installing the latest update from Microsoft. Because earlier today, I installed some updates and after that, the problem started to appear. (After system restore, same problem.) Latest Programs installed before the problem MS Visual Studio 2013 (but internet still worked fine after the install). I hope someone could provide answers on this problem. It is my first time encountering this. EDIT: Additional Info OS: Windows 7 SP1 64-bit AV: Avast Free Antivirus Internet Connection Type: Ethernet It appears that my Laptop can't even connect to the machine thru Remote Desktop My laptop and phone on WiFi works fine and can connect to the internet. EDIT 2: Whenever I boot into Safe Mode, my Internet is fine.

    Read the article

  • WebDav System Error 67 in Windows XP

    - by Nixphoe
    Issue: I'm having issues getting WebDav to work in the command line on Windows XP, both Service Pack 2 and Service Pack 3. C:\>net use z: https://mywebsite.com/software/ System error 67 has occurred. The network name cannot be found. I have tested this with two webdav server. Both Ubuntu Apache and I Windows Server 2003 IIS. Both get the same result. Things That Haven't Worked: I've installed the following Microsoft KB on my XP machines with no avail. I've also found the following reg key: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WebClient\Parameters UseBasicAuth REG_DWORD 1 I try the following when trying to use a few work around I've dug up on the web, all producing the same result. net use z: https://mywebsite.com/software net use z: https://mywebsite.com/software# net use z: https://mywebsite.com/software/ net use z: https://mywebsite.com/software/# I've also tried all the above combinations adding a user into it /user:user and /user:user@domain. I've also tried using http:// rather than https://. I've tried "\\server.com@ssl:443\folder" I've gone over networking related issues as @WesleyDavid had pointed out. Things that do work: I can connect to the webdav folder via the URL and with mapping in Network Place, with XP. But the command line doesn't work (I need a drive letter). Windows 7 works perfectly with the same command. My Delemma: I need this to work with a drive letter. What else can I try to get this working?

    Read the article

  • Windows Firewall Software to Filter Transit Traffic

    - by soonts
    I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

    Read the article

  • How to restore icons to default in Windows 7

    - by Shiki
    Installed a theme by "ZeusOSX". The problem is that I removed all the files, copied back the dll's, did a sfc /scannow (which still found some problem) and now I still have the MAC like folder icons. How can one reset them back to the original state ?

    Read the article

  • Port Forwarding failing only to Ubuntu servers from Draytek router

    - by Rufinus
    I know this is a kinda unusal question, but Draytek support (..which is very eager to solve the issue) seems to reach its limits. Scenario: Draytek Vigor Multiwan router with current firmware. Multiple WAN IP Aliases on one of the wan ports DMZ (or port forwarding doesnt matter) from wan ip alias to internal host currently i have two internal hosts: 192.168.0.51 (Ubuntu) 192.168.0.53 (Debian) both should be accessible from outside via one of the wan ip aliases. both are accessible with their internal ip's at all times (!) If the router gots restartet, both external ips are forwarding to its internal hosts. But after a few minutes up to 2 hours, the ubuntu host is no longer reachable via its external interface. The debian hosts on the other hand is reachable. In what does ubuntu differs from debian ? I know at least of one user with the exact same problem. see http://ubuntuforums.org/showthread.php?p=10994279 Any ideas ? TIA EDIT: via ping diagnostics directly on vigor, 192.168.0.53 is pingable, 192.168.0.51 is not. but both hosts are perfectly reachable from anywhere inside the network. if i restart ubuntu networking it works again for a short time.... i'm out of ideas.. EDIT 2: after further investigation, i noticed a ping from .51 to the network (or a host in the internet) is enough to make the port-forwarding working again. So i will add an Cronjob as a "keep-alive" ping. This will solve the problem, but the reason for this behaivor is still in the dark. Thanks to all commentors.

    Read the article

< Previous Page | 506 507 508 509 510 511 512 513 514 515 516 517  | Next Page >