Search Results

Search found 14079 results on 564 pages for 'folding at home'.

Page 520/564 | < Previous Page | 516 517 518 519 520 521 522 523 524 525 526 527  | Next Page >

• Recover harddrive data

  - by gameshints

  I have a dell laptop that recently "died" (It would get the blue screen of death upon starting) and the hard drive would make a weird cyclic clicking noises. I wanted to see if I could use some tools on my linux machine to recover the data, so I plugged it into there. If I run "fdisk" I get: Disk /dev/sdb: 20.0 GB, 20003880960 bytes 64 heads, 32 sectors/track, 19077 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Disk identifier: 0x64651a0a Disk /dev/sdb doesn't contain a valid partition table Fine, the partition table is messed up. However if I run "testdisk" in attempt to fix the table, it freezes at this point, making the same cyclical clicking noises: Disk /dev/sdb - 20 GB / 18 GiB - CHS 19078 64 32 Analyse cylinder 158/19077: 00% I don't really care about the hard drive working again, and just the data, so I ran "gpart" to figure out where the partitions used to be. I got this: dev(/dev/sdb) mss(512) chs(19077/64/32)(LBA) #s(39069696) size(19077mb) * Warning: strange partition table magic 0x2A55. Primary partition(1) type: 222(0xDE)(UNKNOWN) size: 15mb #s(31429) s(63-31491) chs: (0/1/1)-(3/126/63)d (0/1/32)-(15/24/4)r hex: 00 01 01 00 DE 7E 3F 03 3F 00 00 00 C5 7A 00 00 Primary partition(2) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) (BOOT) size: 19021mb #s(38956987) s(31492-38988478) chs: (4/0/1)-(895/126/63)d (15/24/5)-(19037/21/31)r hex: 80 00 01 04 07 7E FF 7F 04 7B 00 00 BB 6F 52 02 So I tried to mount just to the old NTFS partition, but got an error: sudo mount -o loop,ro,offset=16123904 -t ntfs /dev/sdb /mnt/usb NTFS signature is missing. Ugh. Okay. But then I tried to get a raw data dump by running dd if=/dev/sdb of=/home/erik/brokenhd skip=31492 count=38956987 But the file got up to 59885568 bytes, and made the same cyclical clicking noises. Obviously there is a bad sector, but I don't know what to do about it! The data is still there... if I view that 57MB file in textpad... I can see raw data from files. How can I get my data back? Thanks for any suggestions, Solution: I was able to recover about 90% of my data: Froze harddrive in freezer Used Ddrescue to make a copy of the drive Since Ddrescue wasn't able to get enough of my drive to use testdisk to recover my partitions/file system, I ended up using photorec to recover most of my files

  Read the article

• Looking for Fiddler2 help. connection to gateway refused...just got rid of a virus?

  - by john mackey

  I use Fiddler2 for facebook game items, and it's been a great success. I accessed a website to download some dat files I needed. I think it was eshare, ziddu or megaupload, one of those. Anyway, even before the rar file had downloaded, I got this weird green shield in the bottom right hand corner of my computer. It said a Trojan was trying to access my computer, or something to that extent. It prompted me to click the shield to begin anti-virus scanning. It turns out this rogue program is called Antivirus System Pro and is pretty hard to get rid of. After discovering the rogue program, I tried using Fiddler and got the following error: [Fiddler] Connection to Gateway failed. Exception Text: No connection could be made because the target machine actively refused it 127.0.0.1:5555 I ended up purchasing SpyDoctor + Antivirus, which I'm told is designed specifically for getting rid of these types of programs. Anyway, I did a quick-scan last night with spydoctor and malware bytes. Malware picked up 2 files, and Spydoctor found 4. Most were insignificant, but it did find a worm called Worm.Alcra.F, which was labeled high-priority. I don’t know if that’s the Anti-Virus Pro or not, but SpyDoctor said it got rid of all of those successfully. I tried to run Fiddler again before leaving home, but was still getting the "gateway failed" error. Im using the newest version of firefox. When I initially set up the Fiddler 2.2.8.6, I couldn’t get it to run at first, so I found this faq on the internet that said I needed to go through ToolsOptionsSettings and set up an HTTP Proxy to 127.0.0.1 and my Port to 8888. Once I set that up and downloaded this fiddler helper as a firefox add-on, it worked fine. When I turn on fiddler, it automatically takes my proxy setting from no proxy (default) to the 127.0.0.1 with Port 8888 set up. It worked fine until my computer detected this virus. Anyway, hopefully I've given you sufficient information to offer me your best advice here. Like I said, Spydoctor says the bad stuff is gone, so maybe the rogue program made some type of change in my fiddler that I could just reset or uncheck or something like that? Or will I need to completely remove fiddler and those dat files and rar files I downloaded? Any help would be greatly appreciated. Thanks for your time.

  Read the article

• UPS vs Solar Power in case of power failure for a server [on hold]

  - by Zen 8000k

  I am looking for a low power, low end pc able to run 24/7 without overheating and a way to support it in case of power failure. Power failures can be up to 72 hours. The pc dosen't need a monitor or keyboard. A modem must also be protected in case of power failure. When i say low end, i don't mean crap. The cpu needs to be x86 and have at least 1k cpu in this chart: http://www.cpubenchmark.net/index.php What's the best way to do this? EDIT: more info. I need to run a home server. The server will perform light tasks mainly. A x86 cpu sadly is the only route for my use. I want to be able to run the server and the router/modem in case of power failure. Now, regarding how long the power will fail: 1) 1 hours is OK for most situations. (say 90%) 2) 3 hours is OK (say 98%) 3) 6 hours is more thank OK. (say 99.5%) 4) On extreme cases the power might fail days. I believe this is very unlikely to happen. More is great but, really, how ofter power will fail more than 3 hours? I believe once every year at best. Well, that's too rare to care about. Given the above, I am looking for a cost effective way to archive 1-3 hour power or 6 hour if possible. Solutions: You guys give me great ideas. 1) Power generator: no good as power will fail for 10 seconds before returning. Also I read online, "clean" power generators cost 1.5k+, so it's out of budged. Non clean generator might damage electronics, right? 2) Solar power: i don't know for sure about this. Sounds like a great idea, too good to be true, honestly. For only 200$ i get 100+w? What are the drawbacks here? 3) UPS: This seems to be the best. The only problem is the cost. Cost < 200$ = great 400$ = budged limit

  Read the article

• Why do some games randomly turn my screen a random solid color?

  - by Emlena.PhD

  When playing some games my computer will randomly have an error that I cannot fix without turning it off and back on again. The screen changes to one solid color, which varies (off the top of my head I can remember seeing solid green, magenta, etc..) and the sound blares a single tone. The sound sometimes briefly restores and I can still hear the game sounds and even hear and still be heard by people in my Mumble channel, but the screen doesn't right itself so I'm still blind. What's more is this happens in some games but not in others. While the game is actually running, not while I'm still in the menu. However, it does happen if I'm afk or idle but the game world is still rendering. Games where the error occurs: League of Legends World of Warcraft Trine The Sims 2 Dungeon Defenders Safe games: games where it has never occurred: Tribes: Ascend Star Wars: the Old Republic Battlefield 3 So relatively older games cause the problem while newer games do not? I cannot predict when it will happen, it just seems random. However, if it happens and I try playing the same game further after restart it does appear to occur more frequently after the first time. But if I switch to a safe game it doesn't continue happening. Both of my RAM sticks appear fine, flipped position or either one on their own and games still run, computer still boots. I would think over-heating, but then why not all games? ALso, sometimes it happens immediately after I start playing, within seconds of the 3D world booting up. I'm looking to upgrade very soon so I want to figure out what component or software is fubar and replace/repair it. Any suggestions or recommendations of tools would be helpful. Below is some system information. Dxdiag does not detect any problems. Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120305-1505) System Manufacturer: Gigabyte Technology Co., Ltd. System Model: EP45-UD3R BIOS: Award Modular BIOS v6.00PG Processor: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (2 CPUs), ~3.2GHz Memory: 4096MB RAM DirectX Version: DirectX 11 DxDiag Version: 6.01.7601.17514 64bit Unicode Graphics card name: NVIDIA GeForce GTX 285 Driver Version: 8.17.12.9610 (error has occurred w/several driver versions) Sound: I do not have a sound card, been using motherboard's built in sound)

  Read the article

• Need advice on which PCI SATA Controller Card to Purchase

  - by Matt1776

  I have a major issue with the build of a machine I am trying to get up and running. My goal is to create a file server that will service the needs of my software development, personal media storage and streaming/media server needs, as well as provide a strong platform for backing up all this data in a routine, cron-job oriented German efficiency sort of way. The issue is a simple one - all my drives are SATA drives and my motherboard controller only contains 4 ports. Solving the issue has proven to be an unmitigated nightmare. I would like advice on the purchase of the following: 4 Port internal SATA / 2 Port external eSATA PCI SATA Controller Card that has the following features and/or advantages: It must function. If I plug it in and attach drives, I expect my system to still make it to the Operating System login screen. It must function on CentOS, and I mean it must function WELL and with MINIMAL hassle. If hassle is unavoidable, there shall be CLEAR CUT and EASY TO FOLLOW instructions on how to install drivers and other supporting software. I do not need nor want fakeRAID - I will be setting up any RAID configurations from within the operating system. Now, if I am able to find such a mythical device, I would be eternally grateful to whomever would be able to point me in the right direction, a direction which I assume will be paved with yellow bricks. I am prepared to pay a considerable sum of money (as SATA controller cards go) and so paying anywhere between 60 to 120 dollars will not be an issue whatsoever. Does such a magical device exist? The following link shows an "example" of the type of thing I am looking for, however, I have no way of verifying that once I plug this baby in that my system will still continue to function once I've attached the drives, or that once I've made it to the OS, I will be able to install whatever drivers or software programs I need to make it work with relative ease. It doesn't have to be dog-shit simple, but it cannot involve kernels or brain surgery. http://www.amazon.com/gp/product/B00552PLN4/ref=pd_lpo_k2_dp_sr_1?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B003GSGMPU&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=1HJG60XTZFJ48Z173HKY So does anyone have a suggestion regarding the subject I am asking about? PCI SATA Controller Cards? It would help if you've had experience with the component before - that is after all why I am asking here - for those who have had experience that I do not have. Bear in mind that this is for a home setup and that I do not have a company credit card. I have a budget with a 'relative' upper limit of about $150.00.

  Read the article

• rsync -c -i flags identical files as different

  - by Scott

  My goal: given a list of files on local server, show any differences to the files with the same absolute path on remote server; e.g. compare local /etc/init.d/apache to same file on remote server. "Difference" for me means different checksum. I don't care about file modification times. I also do not want to sync the files (yet); only show the diffs. I have rsync 3.0.6 on both local and remote servers, which should be able to do what I want. However, it is claiming that local and remote files, even with identical checksums, are still different. Here's the command line: $ rsync --dry-run -avi --checksum --files-from=/home/me/test.txt --rsync-path="cd / && rsync" / me@remote:/ where: "me" = my username; "remote" = remote server hostname current working directory is '/' test.txt contains one line reading "/etc/init.d/apache" OS: Linux 2.6.9 Running cksum on /etc/init.d/apache on both servers yields the same result. The files are the same. However, rsync output is: me@remote's password: building file list ... done .d..t...... etc/ cd+++++++++ etc/init.d/ <f+++++++++ etc/init.d/apache sent 93 bytes received 21 bytes 20.73 bytes/sec total size is 2374 speedup is 20.82 (DRY RUN) The output codes (see http://www.samba.org/ftp/rsync/rsync.html) mean that rsync thinks /etc is identical except for mod time /etc/init.d needs to be changed /etc/init.d/apache will be sent to the remote server I don't understand how, with --checksum option, and the files having identical checksums, that rsync should think they're different. (I've tried with other files having identical mod times, and those files are not flagged as different.) I did run this in /, and made sure (AFAIK) that it's run remotely in /, so even relative pathnames will still be correct. I ran rsync with -avvvi for more debug info, but saw nothing remarkable. I'm wondering: is rsync still looking at file mod times, even with --checksum? am I somehow not setting up the path(s) right? what am I doing wrong?

  Read the article

• Why is the server performance so poor? What can be done to improve the speed of the server?

  - by fslsyed

  Very slow processing using Windows Server2008 R2 Standard with Service Pack One. Situation: Read a text file using the text data to populate a series of MS Sql tables. The converted data is used to generate monthly PDF invoice files; the PDF files are saved directly to the hard drive. The application is multi-threading with one thread used for the text conversion and three threads for PDF invoice generation. The text conversion is occurring concurrently with the invoice generation. Application Software: C# using Microsoft Visual Studio 2010 Ultimate. Crystal Report Writer 2011 with runtime 13_0_3 64 bit version. Targeted platform is x64; also tested as x86, and Any CPU with similar results. Microsoft .NET Framework 4.0. Microsoft Sql 2008 Issue: The software is running very slowly. The conversion of the text file is approximately six hundred fifty records per second and generation of the PDF files is approximately twelve invoices per minute. The text file to be converted is six hundred Meg with seven thousand invoices to be generated. The software was installed on three different machines from the same distribution files. The same text file was converted on each machine. The user executing the application was an administrator on each machine. The only variances were the machine and operating system. The configurations are as follows: Server: Operating System: Windows Server2008 R2 Standard 64-bit (6.1, Build7601) SP1 Service Pack: System Manufacturer: IBM System Model: System x3550 M3-[7944AC1]- BIOS: Default System BIOS Processor: Intel® Xeon® CPU E5620@ 2.4GHz (16 CPUs) Memory: 16384MB Notebook: Operating System: Windows 7 Home Premium Standard 64-bit (6.1, Build7601) System Manufacturer: Hewlett-Packard System Model: HP Pavilion dv7 Notebook PC BIOS: Default System BIOS Processor: AMD Phenom II N640 Dual-Core Processor 2.9GHz (2 CPUs) Memory: 6144MB Desktop: Operating System: Windows 7 Professional 64-bit (6.1, Build7601) SP1 System Manufacturer: Dell Inc. System Model: OptiPlex 960 BIOS: Phoenix ROM BIOS PLUS Version 1.10 A11 Processor: Intel Core™2 Quad CPU Q9650 @3.00GHZ (4 CPUs) Memory: 16384MB Processing results per machine: The applications were executed seven times with the averages being displayed below. Machine Text Records Invoices Generated Converted Per Minute Per Minute Server (1) 650 12 Notebook 980 17 Desktop 2,100 45 (1) The server is dedicated to execution of this application; no additional applications are being executed. Question: Why is the server performance so poor? What can be done to improve the speed of the server?

  Read the article

• Server 2008/Windows 7/Samba Unspecified error 80004005

  - by ancillary

  I have a Samba share on a LAN with 2008 PDC/DNS. Smb authenticates with AD and I have several Win7 Machines that can connect fine. I recently added a couple of new computers to the LAN which were imaged the same way (same software, etc.; different hardware so different drivers) as the other machines and they have the same policies set. I can not get the new machines to connect to the samba share no matter what. I am always met with either Unspecified Error 0x80004005 or Network Path not found. I've turned off the firewall; set LANMAN auth to respond to NTLM only/send LM & NTLM responses/use NTLM session security if negotiated in Local Sec Policy SEcurity Options; tried both ip and hostname to connect. SMB log shows that authentication succeeds; but then connection is immediately killed by the client. tcpdump shows nothing remarkable except that when trying to connect from the client via hostname there is an unknown packet type error: ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) Here's a couple of lines from that error: 11:18:37.964991 IP 001-client.domain.local.49372 > smb.domain.local.netbios-ssn: P 1670:2146(476) ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) [000] AA 46 96 FA D5 99 33 75 0C C4 20 CE 26 42 F3 61 \252F\226\372\325\2313u \014\304 \316&B\363a [010] F0 8C FB 65 18 17 40 A5 DB 42 BB 94 37 53 92 EC \360\214\373e\030\027@\245 \333B\273\2247S\222\354 [020] 55 98 7F C4 AE 3D 6B 10 C4 U\230\177\304\256=k\020 \304 11:18:37.964998 IP smb.domain.local.netbios-ssn > 001-client.domain.local.49372: . ack 2146 win 100 Here's smb.conf just in case (though don't see how if other machines are working fine): [global] workgroup = MYDOMAIN realm = MYDOMAIN.LOCAL server string = domain|smb share interfaces = eth1 security = ADS password server = 192.168.1.3 log level = 2 log file = /var/log/samba/%m.log smb ports = 139 strict locking = no load printers = No local master = No domain master = No wins server = 192.168.1.3 wins support = Yes idmap uid = 500-10000000 idmap gid = 500-10000000 winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes [samba-share1] comment = SMB Share path = /home/share/smb/ valid users = @"MYDOMAIN+Domain Users" admin users = @"MYDOMAIN+Domain Admins" guest ok = no read only = No create mask = 0765 force directory mode = 0777 Any ideas what else I could try or look for? Or what might be the problem? Thanks.

  Read the article

• Nagios shell script cannot be executed

  - by MeinAccount

  I'm trying to monitor GitLab with nagios. I've created the following command definition and shell script but when checking the service I'm receiving the following e-mail. How can I solve this? The file is executable. [...] nagios : 3 incorrect password attempts ; TTY=unknown ; PWD=/ ; USER=git ; COMMAND=/bin/bash -c /var/lib/nagios/custom_plugins/check_gitlab.sh Command definition: define command { command_name custom_check_gitlab command_line /var/lib/nagios/custom_plugins/check_gitlab.sh } Shell script: #! /bin/sh # [...] RAILS_ENV="production" # Script variable names should be lower-case not to conflict with internal /bin/sh variables such as PATH, EDITOR or SHELL. app_root="/home/git/gitlab" app_user="git" unicorn_conf="$app_root/config/unicorn.rb" pid_path="$app_root/tmp/pids" socket_path="$app_root/tmp/sockets" web_server_pid_path="$pid_path/unicorn.pid" sidekiq_pid_path="$pid_path/sidekiq.pid" ### Here ends user configuration ### # Switch to the app_user if it is not he/she who is running the script. if [ "$USER" != "$app_user" ]; then sudo -u "$app_user" -H -i $0 "$@"; exit; fi # Switch to the gitlab path, if it fails exit with an error. if ! cd "$app_root" ; then echo "Failed to cd into $app_root, exiting!"; exit 1 fi ### Init Script functions check_pids(){ if ! mkdir -p "$pid_path"; then echo "Could not create the path $pid_path needed to store the pids." exit 1 fi # If there exists a file which should hold the value of the Unicorn pid: read it. if [ -f "$web_server_pid_path" ]; then wpid=$(cat "$web_server_pid_path") else wpid=0 fi if [ -f "$sidekiq_pid_path" ]; then spid=$(cat "$sidekiq_pid_path") else spid=0 fi } # Checks whether the different parts of the service are already running or not. check_status(){ check_pids # If the web server is running kill -0 $wpid returns true, or rather 0. # Checks of *_status should only check for == 0 or != 0, never anything else. if [ $wpid -ne 0 ]; then kill -0 "$wpid" 2>/dev/null web_status="$?" else web_status="-1" fi if [ $spid -ne 0 ]; then kill -0 "$spid" 2>/dev/null sidekiq_status="$?" else sidekiq_status="-1" fi } check_pids check_status if [ "$web_status" != "0" -a "$sidekiq_status" != "0" ]; then echo "GitLab is not running." exit 2 fi if [ "$web_status" != "0" ]; then printf "The GitLab Unicorn webserver is \033[31mnot running\033[0m.\n" exit 1 fi if [ "$sidekiq_status" != "0" ]; then printf "The GitLab Sidekiq job dispatcher is \033[31mnot running\033[0m.\n" exit 1 fi if [ "$web_status" = "0" -a "$sidekiq_status" = "0" ]; then printf "GitLab and all it's components are \033[32mup and running\033[0m.\n" exit 0 fi

  Read the article

• Default Critique branch office setup: VPNTunnel->HQ, subnets for VOIP/PC, + several Q's

  - by CHickenTaragon

  We're setting up a new branch office. * ~10 users. * Each user has a VOIP phone provided by a hosted solution. * Users need access to resources on HQ (located in another state), so setting up VPN tunnel * HQ only supports certain Cisco/Juniper devices. VOIP provider only supports SonicWall, so current plan is to have two routers w/ separate subnets for VOIP vs. PC traffic. * PC's will plug into pass-thru Ethernet jacks on the VOIP phones, but the phones vs. PC's will point to different subnets. * Cable Modem is 50Mbps / 5Mbps DOCSIS 3.0 business line w/ 5 static IP's. * Each of the 2 subnets will map to one of the 5 public IP's. * May or may not also need to support a VPN tunnel with a second branch office because of a file server they have there that some in the new office use. I'm pushing to have them move the files to a server on the HQ's network so we don't have to worry about setting up an additional tunnel. Questions: Do you foresee any issues with the below set-up? Router recommendations by HQ IT staff: Cisco Router 2811, or Juniper SSG5 or SSG20. Any recommendations about these routers? We need Wi-Fi too – looks like the above routers have models that support this, any reason not to use this? Users need to be able to work from home. If so, how is authentication handled? Right now we use AD credentials for the HQ's domain, but we currently don't plan to have an AD system in the new location since it's only 10 users. We can't tie the authentication system from the new location's router to the AD system of the HQ. All the PC's that will be in the new location are currently in the existing office that is closing down, and are already joined to the domain of the HQ. Please confirm: this + the VPN tunnel will be sufficient for them to connect to authenticated resources on the HQ's network from the new location, correct? Mainly SQL servers and file servers, and a few remote desktop sessions. I'm sure I'll have some more questions, but can't think of them right now.

  Read the article

• Why doesn't video run smoothly on my laptop anymore?

  - by andygrunt

  This might be an impossible question to answer remotely but I figure there may be some common causes that people can suggest so I think it's worth asking... Video no longer plays smoothly on my laptop. It used to but not for a while now. For example, playing a video on YouTube is pretty typical: I press play (making sure it's not on HD or even HQ) and the video buffers a little then starts to play. At first it plays fine then the video starts to stutter, turning into a slideshow while the sound continues to play smoothly. If I try playing the same video on my Playstation 3 (which is linked to the same network) it plays smoothly so it can't be the connection. Another example is streaming DivX videos. Again, I wait while it buffers and it starts but very soon, instead of a slideshow, this time the video just plays slowly while the sound continues as normal (instantly getting out of sync). Even if I let the video fully load before pressing play (i.e. it's no longer streaming), it still behaves the same way. I can even let it load 100% then save the file to hard disk and use VLC player to view it, and the same thing happens. I'm using an old laptop running Windows XP. For the past several years it's been connected to the router via Wi-Fi but in the past few days I've changed that to a network cable (like my PS3) but that hasn't helped. Yes, I regularly install various bits and pieces of software but nothing that I can identify as being the cause. So, are there known causes of this sort of behaviour and if so, what can I do to fix it? Thanks. Update to answer a few questions... Laptop Spec' (note: video has played back fine for the majority of time I've had the laptop) Toshiba Satellite 1900-603 (possibly called something else outside the UK) Intel Pentium 4 2.2 Ghz Processor Originally had 512Mb memory but recently doubled that to 1 Gig of memory Graphics: ATI Mobility Radeon 16Mb DDR VRAM Windows XP SP3 (Home edition) Over the years I've done several things to speed it up (disabling indexing etc) and am generally happy with the performance. I also regularly have a clear out of old software (if for no other reason than the laptop only has a 40Gb hard disk) and use CCleaner and Glary Utilities to strip out much of the crap from my system. Also recently (after doubling the memory), I've tried a few new things which might be likely candidates for slowing the video down such as Rocketdock, Jingle keyboard (which gives an old style 'clacky' typewriter sound when I type - love it), SugarSync, Taskbar Shuffle. However, the video doesn't play smoothly even when I try quit all these apps.

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Google Chrome issues

  - by Ben Hooper

  I'm an avid user of Chrome and would defend it to the death but there is no denying that it has issues, and I've been experiencing a lot of them recently. Issues Stuck tabs Issue: Around 60% of the time (higher when the system has just started), when Chrome is launched, some or all of the pinned tabs and startup pages will get stuck in the counter-clockwise-rotating "contacting server" mode and never snap out of it. Fix: Quit and launch Chrome until they load properly (this really isn't good, as quitting and launching Chrome can and has cleared all pinned tabs). Extra Information: If you stop the loading and re-enter the URL then the page will load perfectly. The amount of pinned tabs or startup pages seems to be irrelevant, but I could be wrong.   "Downloaded/out of" Issue: Each item in the download bar has a downloaded status section, formatted as "downloaded/out of". Sometimes Chrome doesn't display the "out of" part.   Collapsed settings windows Issue: In Chrome version 19(ish)+, settings are configured via overlayed / popup windows. Sometimes, the window will open fully collapsed. Fix: Resize Chrome's window or open the developer tools. "Network Error" with large downloads Issue: Sometimes, when downloading large files (500MB+) Chrome will download the entire file, the download status will freeze (for example, "1 GB/1 GB") for a few minutes, report "Network error", and delete the .crdownload file. Extra Information: The same file from the same website on the same computer downloads perfectly in other browsers. The website and file type seem to be irrelevant.   Information: I've experienced some of these issues on my home PC and some on my work PC, both of which are Windows 7 Ultimate x64. The only things that link them are my Google account (all settings are synced). Updating Chrome hasn't worked. Most of these issues presented themselves around about version 17 and have continued right through to 21 (current). Uninstalling Chrome, deleting all data in %programFiles(x86)%\Google and %localAppData%\Google, and reinstalling hasn't worked. I have yet to see whether disabling all extensions would make a difference, but it's hard to diagnose as these issues don't occur 100% of the time.   In my case, I don't know if there's an actual solution. I'm just curious as to whether anyone else is having similar issues to those that I'm experiencing. At least then I'll know it's an issue with Chrome itself.

  Read the article

• Building a Mac/PC Network in a Dorm with Network Restrictions

  - by user70340

  I have been a Windows XP user for the last few years, but I recently bought a 15'' MacBook Pro for research purposes. I would like to set up a no-hassle Mac/PC Network at home so that I can access the internet on both computers and hardware between computers (i.e. a harddrive, or a mouse/keyboard with Synergy). Unfortunately, I live in a dorm with silly network restrictions so a solution is not straightforward. In particular: The dorm has a wired and wireless network, both which provide an internet connection. The wired network provides way faster internet (download speeds of 15 MB/s vs. 2 MB/s on wireless), so I would like to somehow exploit this, at least on my PC for Bittorrent :) Multiple devices can connect to the wireless network, but cannot "see" each other on the network (so software like Synergy would not work). Only 1 MAC address can connect to the wired network at a time. Ideally I would just connect a wireless router to the wired network and then have both the Mac and the PC on that, but the 1 MAC address restriction will not allow the both computer to access the internet simultaneously. I cannot think of a way to bypass this restriction (though I'm not network savvy), so I am planning to create a private no-internet network to allow the devices to see each other and share hardware. Here are some thoughts. I would appreciate any feedback at all! If I build a private wireless network: (first choice) I will use a wireless router that is not connected to the internet. My PC and Mac will be connected to each other wirelessly. I can then connect the PC to the internet via a wired network, but then the Mac will not have internet access as its wireless card is already in use. In this case, could I stream internet access from the PC to the Mac via the wireless network? Or could I buy a USB wireless card for the Mac so that it can connect to both my private network and the dorm network? If I build a private wired network: (second choice) Then both the PC and the Mac will connect to the internet wirelessly, which means I cannot take advantage of the faster download speeds.

  Read the article

• Firefox can't establish a connection to the server at www.google.com

  - by Tom

  My home page in Firefox [v4.0] and Internet Explorer [v9.0.8112.16421, Update Versions RTM (KB982861)] is currently set to Google but when I depress the quick start icon to start up either browser, I am getting the following immediate results: Unable to connect (In Firefox) Firefox can't establish a connection to the server at www.google.com. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Internet Explorer cannot display the webpage What you can try: Diagnose Connection Problems More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. There might be a typing error in the address. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For offline users You can still view subscribed feeds and some recently viewed webpages. To view subscribed feeds: Click the Favorites button , click Feeds, and then click the feed you want to view. To view recently visited webpages (might not work on all pages): Press Alt, click File, and then click Work Offline. Click the Favorites button, click History, and then click the page you want to view. Thankfully, I am able to use one browser that I have installed on my computer (Mathon v3.0.20.5000) to search online for technical assistance in this matter. I have seen several WinSock error issues mentioned; but, they are pointing to Windows XP and I am using Windows 7 Pro and remain uncertain whether anything identified as a fix for one OS will work in another. Things I've tried: HiJackThis Complete scan with Avira AntiVirus Premium. What am I overlooking? What should I do to address this problem?

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Postfix + SASLAUTHD + MySQL authentication problems

  - by Or W

  I've been trying to sort this out for the past 6 hours or so, this is the error message I'm facing (Running CentOS x64): /var/log/maillog: Jun 22 20:42:49 ptroa postfix/smtpd[10130]: warning: SASL authentication failure: Password verification failed Jun 22 20:42:49 ptroa postfix/smtpd[10130]: warning: bzq-79-177-192-133.red.bezeqint.net[79.177.192.133]: SASL PLAIN authentication failed: authentication failure Jun 22 20:42:49 ptroa postfix/smtpd[10130]: warning: bzq-79-177-192-133.red.bezeqint.net[79.177.192.133]: SASL LOGIN authentication failed: authentication failure /var/log/messages: Jun 22 20:15:38 ptroa saslauthd[9401]: do_auth : auth failure: [user=myuser] [service=smtp] [realm=domain.com] [mech=pam] [reason=PAM auth error] I have dovecot installed as well and I'm able to receive emails via the MySQL authentication. The problem is when I'm trying to use SMTP to send out emails. Some config files: /etc/postfix/main.cf: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. myorigin = /etc/mailname smtpd_banner = Server Message biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = /usr/share/doc/postfix # TLS parameters smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = domain.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all html_directory = /usr/share/doc/postfix/html message_size_limit = 30720000 virtual_alias_domains = virtual_alias_maps = proxy:mysql:/etc/postfix/mysql-virtual_forwardings.cf, mysql:/etc/postfix/mysql-virtual_email2email.cf virtual_mailbox_domains = proxy:mysql:/etc/postfix/mysql-virtual_domains.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailboxes.cf virtual_mailbox_base = /home/vmail virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 smtpd_sasl_auth_enable = yes broken_sasl_auth_clients = yes smtpd_sasl_authenticated_header = yes smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination virtual_create_maildirsize = yes virtual_maildir_extended = yes proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $relay_domains $canonical_maps $sender_canonical_maps $recipient_cano$ virtual_transport = dovecot dovecot_destination_recipient_limit = 1 /etc/default/saslauthd: START=yes DESC="SASL Authentication Daemon" NAME="saslauthd" MECHANISMS="pam" MECH_OPTIONS="" THREADS=5 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd -r" /etc/pam.d/smtp: #%PAM-1.0 #auth include password-auth #account include password-auth auth required pam_mysql.so user=mail_admin passwd=password host=127.0.0.1 db=mail table=users usercolumn=email passwdcolumn=password crypt=1 verbose=1 account sufficient pam_mysql.so user=mail_admin passwd=password host=127.0.0.1 db=mail table=users usercolumn=email passwdcolumn=password crypt=1 verbose=1

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• Mysql Servers for Attendance System

  - by foo

  I'm building an attendance system. There are about 20 places where people will check in and check out using Mifare 1K Card. It will use MySQL as the database. The system will display something like "#ID IN: 800AM" when the first time the user checks in and "#ID OUT: 400PM" when the user checks out. For this to work, all the databases need to be synchronized with each other all the times. For an example, if user A went to location #1 to check in but by the time he wants to return home, the server at location #1 went down, he needs to go to location #2 or the nearest server to check out. The server at location #2 should display '#ID OUT: 400PM" and not "#ID IN: 400PM" since he's already checked in. So, what should I use to ensure this idea will work? My main concern is with the network (other department manages it) which is very unpredictable. It just love to go down anytime it wants to. Update LOL, didn't realize my question is not clear, just noticed it when you guys pointed it out, sorry about that. My real question is, how can I configure my MySQL to be synchronized with each other (20 servers)? MySQL cluster ? (tried reading about it, but I'm not sure if it's the right thing to do) My current setup (first phase): Local database for each server OS: Slackware A main server that keeps track which staff is at which server A web based front end for the user to see their history (which connects to the server based on their records) Main Pros No worries about network problems since it is a local database Main Cons A user can only check in and out at the same server. Databases/Servers are not connected with each others. Have to add the user to each server if the users want to check in at different locations. Which means, if he wants to go to location A, he must be checked out from location A first and then check in at location B. The server at location B didn't know that the user has checked in before at A. By the way, I've already centralized my NTP to a local server. About the network, let's just say, I don't have the authority to make changes so that the network will be better. The network won't effect all 20 servers at once, usually, just a few of them for several times a week. If there are anything else you would like me to answer, please just ask.

  Read the article

• Problems set-up Single Sign-On using Kerberos authentication

  - by user1124133

  I need for Ruby on Rail application set authentication via Active Directory using Kerberos authentication. Some technical information: I are using Apache installed mod_auth_kerb In httpd.conf I added LoadModule auth_kerb_module modules/mod_auth_kerb.so In /etc/krb5.conf I added following configuration [logging] default = FILE:/var/log/krb5libs.log kdc = FILE:/var/log/krb5kdc.log admin_server = FILE:/var/log/kadmind.log [libdefaults] default_realm = EU.ORG.COM dns_lookup_realm = false dns_lookup_kdc = false ticket_lifetime = 24h forwardable = yes [realms] EU.ORG.COM = { kdc = eudc05.eu.org.com:88 admin_server = eudc05.eu.org.com:749 default_domain = eu.org.com } [domain_realm] .eu.org.com = EU.ORG.COM eu.org.com = EU.ORG.COM [appdefaults] pam = { debug = true ticket_lifetime = 36000 renew_lifetime = 36000 forwardable = true krb4_convert = false } When I test kinit validuser and enter password then authentication is successful. klist returns: Ticket cache: FILE:/tmp/krb5cc_600 Default principal: [email protected] Valid starting Expires Service principal 02/08/13 13:46:40 02/08/13 23:46:47 krbtgt/[email protected] renew until 02/09/13 13:46:40 Kerberos 4 ticket cache: /tmp/tkt600 klist: You have no tickets cached In application Apache configuration I added IfModule mod_auth_kerb.c> Location /winlogin> AuthType Kerberos AuthName "Kerberos Loginsss" KrbMethodNegotiate off KrbAuthoritative on KrbVerifyKDC off KrbAuthRealms EU.ORG.COM Krb5Keytab /home/crmdata/httpd/apache.keytab KrbSaveCredentials off Require valid-user </Location> </IfModule> I restarted apache Now some tests: When I try to access application from Win7, I got pop-up message box, with text: Warning: This server is requesting that your username and password be sent in an insecure manner (basic authentification without a secure connection) When I enter valid credentials then my application opens successfully, and all works fine. Questions: Is ok that for user pop-ups such windows? If I use NTLM authentication then there no such pop-up. I checked IE Internet Options and there 'Enable Integrated Windows Authentication' is checked. Why IE try to send username and password to application apache? If I correct to understand then Windows self must make authentication via Active Directory using Kerberos protocol. When I try to access application from Win7 and I enter incorrect credentials to pop-up message box Application say Authentication failed (this is OK) In apache error log I see: [error] [client 192.168.56.1] krb5_get_init_creds_password() failed: Client not found in Kerberos database But now I cannot get possibility to enter valid credentials, only when I restart IE I can get again pop-up box. What could be incorrect or missing in my Kerberos setup? I read in some blog post that probably something is needed to be done in Active Directory side. What exactly?

  Read the article

• How do Windows 7 encrypted files look like?

  - by Sean Farrell

  Ok this is kind of an odd question: How do Windows 7 (Home Premium) encrypted files look like "from the outside"? Now here is the story. An acquaintance of a freind of mine got a nasty virus / scareware. So I wiped out my PC technician cap and went to work on it. What I did was remove the drive from the laptop and put drive into my external drive bay. I scanned the drive and yes it was loaded with stuff. That basically cured the infection and I could start the system back up. To check if it cured the problem I wanted to see the system while running. There where two user accounts, on with a password and one without (both admin users !?!). So I logged into the unprotected user and cleaned up the residual issues, like proxy server to localhost in the browser config. Now I wanted to do the same for the password protected user. What I noticed that from my system and the unprotected user account the files of the protected user looked garbled. The files are something like 12 random alphanum chars, but the folders looked ok. Naive as was thought this might be how encrypted files looked "from the outside". (I never use Microsoft's own security features, so how would I know. TrueCrypt is one big blob.) Since the second user could not be reached, I though sod it and removed the password from the account. (That might have been a mistake, I know.) Now I did the same clean up tasks and all nice and fine; except for the files which where still "encrypted". So I looked into many Windows Encrypted Files recovery posts and not all hope is lost, since I should be able to extract the certificate and with the password regain access to the files. Also note that windows did "only" prompt me that removing the password would be insecure, not that access to encrypted files would be lost, like it is claimed in most recovery articles. Resetting the password did not help and I gave up for the night. The question that nagged me half of the last night was, what if the files are not encrypted, but the scare-ware encrypted / destroyed the files? I don't want to spend hours of work trying to recover files that are not recoverable. The ting is that the user does not remember turning it on and aren't the files marked in blue and the filename is readable? Many thanks for input from users who have more knowledge about WEF...

  Read the article

• My network drive disappears from Mac OS Finder

  - by Mariusz

  I have recently bought a Netgear WNDR3800 router to use it in my home network. But just the same day I installed it, I noticed a strange behaviour of Finder and iTunes. Let me explain it further. There is a Synology DS111 NAS attached to that router and two Macs with Mac OS X Lion. One of them is connected by a cable and the second one wirelessly. Before I changed my router to the new one I mentioned above, Finder always used to display my NAS on its sidebar. So I could just click its network name to access shared folders existing on it. But after I installed WNDR3800, I can no longer access the NAS that way. It is no longer displayed. I always have to mount it manually by typing its IP address using the Finder's 'connect to server' option. The same NAS supports TimeMachine backups and has an inbuilt DLNA server. And the same situation here. I can't perform a backup because my NAS is no longer accessible in TimeMachine preferences. iTunes does not display it as well (as a multimedia server) even though it used to before I installed that router. What's important, everything works fine for a couple of minutes after I restart the router or the NAS. Or even when I change the NAS's IP address it becomes accessible again in Finder, TimeMachine and iTunes, but only for some time. Both the Mac computers I mentioned behave the same way. And all those issues have been taking place sice I installed that new router. Before I did that, everything had worked fine. My old router was Netgear WGR614v10. Would you be so kind to tell me what you think could possibly be the reason of that behaviour? What settings of the router should I look closer at? I'm not a network specialist, but is it possible that some network packets are blocked for some reason? I will be grateful for any clues you give me. Thank you.

  Read the article

• NFS4 / ZFS: revert ACL to clean/inherited state

  - by Keiichi

  My problem is identical to this Windows question, but pertains NFS4 (Linux) and the underlying ZFS (OpenIndiana) we are using. We have this ZFS shared via NFS4 and CIFS for Linux and Windows users respectively. It would be nice for both user groups to benefit from ACLs, but the one missing puzzle piece goes thusly: Each user has a home, where he sets a top-level, inherited ACL. He can later on refine permissions for the contained files/folders iteratively. Over time, sometimes permissions need to be generalized again to avoid increasing pollution of ACL entries. You can tweak the ACL of every single file if need be to obtain the wanted permissions, but that defeats the purpose of inherited ACLs. So, how can an ACL be completely cleared like in the question linked above? I have found nothing about what a blank, inherited ACL should look like. This usecase simply does not seem to exist. In fact, the solaris chmod manpage clearly states A- Removes all ACEs for current ACL on file and replaces current ACL with new ACL that represents only the current mode of the file. I.e. we get three new ACL entries filled with stuff representing the permission bits, which is rather useless for cleaning up. If I try to manually remove every ACE, on the last one I get chmod A0- <file> chmod: ERROR: Can't remove all ACL entries from a file Which by the way makes me think: and why not? In fact, I really want the whole file-specific ACL gone. The same holds for linux, which enumerates ACEs starting with 1(!), and verbalizes its woes less diligently nfs4_setacl -x 1 <file> Failed setxattr operation: Unknown error 524 So, what is the idea behind ACLs under Solaris/NFS? Can they never be cleaned up? Why does the recursion option for the ACL setting commands pollute all children instead of setting a single ACL and making the children inherit? Is this really the intention of the designers? I can clean up the ACLs using a windows client perfectly well, but am I supposed to tell the linux users they have to switch OS just to consolidate permissions?

  Read the article

• Virtualbox - routing subnet to bridge adapters

  - by user42384

  Hello, I have set up a Debian Lenny box with 3 vbox Lenny machines running eth0 of the host in bridged mode (on virtualbox 3.1.6). When testing in my local LAN, this all worked perfectly well and traffic flowed to and from the IPs of the virtual machines as it should. However, now that it's in its co-lo home, the networking setup is a bit different, and I'm unable to get traffic to flow to the vboxes properly. Specifically, the host has its own Primary IP, and I have a separate subnet of 8 (6 usable) IPs routed to the box for use by the vboxes. So, eth0 on host is: Machine IP: 2x.x.x.137 Gateway IP: 2x.x.x.138 Subnet Msk: 255.255.255.252 Subnet for vboxes is Subnet: 2x.x.x.240/29 Netmask: 255.255.255.248 vbox1 is configured to 2x.x.x.241 on eth0 as follows: auto eth0 iface eth0 inet static address 2x.x.x.241 netmask 255.255.255.248 Setting up a virtual interface (eth0:0) on the host with one of these subnet IPs allows me to ping to that address only from vbox1, and it allows me to ping vbox1 from the host. I can also ping that virtual interface perfectly well from outside, so the IPs are definitely landing at my machine. It seems I'm missing some sort of routing instruction either on the host or vbox1 to get traffic moving between the subnet and the default gateway, but I can't seem to figure out what it should be, or what glaringly obvious thing i'm missing. Most of my obvious attempts (the gw of eth0, the ip of eth0) were rejected by route command with SIOCADDRT: No such device (eg - i can't find it). I tried setting vbox1 to bridge on eth0:0, but this was not an acceptable device name and VBoxHeadless refused to start. The physical machine does have an unused physical NIC at eth1 that can be used if necessary for something or other. Host machine is running iptables configured by ferm, have experimented with it allowing forwarding for that subnet, but I wouldn't have thought this was necessary given the nature of the virtualbox devices (nor did it actually work). Clearing out all of these rules for a blank iptables set does not resolve the issue. (you can see ferm generated iptables at http://codedumper.com/ojaze) Thanks for any help you can give... Patrick

  Read the article

< Previous Page | 516 517 518 519 520 521 522 523 524 525 526 527  | Next Page >