Search Results

Search found 16947 results on 678 pages for 'kernel programming'.

Page 522/678 | < Previous Page | 518 519 520 521 522 523 524 525 526 527 528 529  | Next Page >

  • Fan not detected by lm-sensors

    - by OrangeTux
    My fan is blowing hard, while my cpu temperature is 32 degrees I tried a lot of things to control my fan. Changed grub file GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi= pci=noacpi" _ GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=\"Linux\"" Ran sensors-detect : To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO) Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK Ran sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +34.0°C (crit = +90.0°C) coretemp-isa-0000 Adapter: ISA adapter Core 0: +34.0°C (high = +80.0°C, crit = +90.0°C) Core 2: +34.0°C (high = +80.0°C, crit = +90.0°C) Ran sudo start module-init-tools and sudo start module-init-tools module-init-tools stop/waiting As you can see my fan isn't detected. Running fancontrol gives me this: Loading configuration from /etc/fancontrol ... Error: Can't read configuration file Can you help me, please? I cannot use my laptop now in class. Thanks in advance. My system 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5400 Series] 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05)

    Read the article

  • Atheros AR928X wireless connection makes neighbourhood machine drop off line

    - by funicorn
    I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

    Read the article

  • Ubuntu Server Cannot Route to the Internet

    - by ejes
    I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

    Read the article

  • Ubuntu won't connect to wired network

    - by djeikyb
    I'm running 10.04, upgraded from 9.10, maybe, but probably not upgraded from 9.04. I have two wifi routers. Zeus is connected to the dsl modem. Hermes uses a wds bridge with Zeus to extend the network. My desktop (Daedalus) is ethernetted to Hermes. My laptop (Clyde) is wifi, switching to Hermes or Zeus as needed. Occasionally, as in whenever I transfer a large file from desktop to laptop, the wds bridge will die. Fixing it means restarting both routers, though it seems Hermes should boot first. This is ridiculous, and eventually I'll get around to asking you guys to help me stop it from happening. More importantly is that my desktop requires a reboot to get back on the network. WTF. ifconfig shows my nic has no ip. /etc/init.d/networking restart doesn't do anything, not even give me a lousy ip. dhcpcd eth1 grants me an ip address, but doesn't help with internet access. route -n shows what looks like my normal routing table, but pinging google.com informs me it's an unknown host. jake@daedalus:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 10.1.1.1 0.0.0.0 UG 0 0 0 eth1 It may be worth noting that I can ping both Zeus (10.1.1.1) and Hermes (10.1.1.4) and my laptop (10.1.1.55). Much obliged for any help. Rebooting is, well, trivial in this instance. But it's stupid. I switched to linux because I like the idea that if one part breaks, you fix it instead of reboot reboot reboot. I've left my poor desktop in disarray, confining myself to my little netbook. My desktop is broken, awaiting magical commands from you brilliant folk. (and yes, i know clyde the netbook should be named icarus. it was its original name. ironically the ssd burned out, and i felt it wasn't right when it came to reinstalling)

    Read the article

  • External hard drive not recognized

    - by sr71
    Installed Ubuntu 10.10 on a hard drive by itself (no windows). All updates are up to date. Everything`works fine except when I plug in a 320 gig Toshiba external hard drive....it is not recognized. When I plug in an 8 gig flash drive it is recognized no problem. What do I mean by "not recognized"? I mean: how do you know it was not recognized. You can check the command "cat /proc/partitions" in a terminal with and without the hdd attached. If you see some difference, it's ok. If the difference is something like "sda1" (sd+letter+number) then you have partition on it, maybe it can't be handled in Ubuntu (no filesystem on it or so). If there is only "sda" in the difference for example (sd+letter, but no number after it) then the drive itself is detected, just no partition is created on it. Also you can check out the messages of the kernel, with the "dmesg" command in the terminal. If there is no disk/partition/anything in /proc/partitions, there can be an USB level problem, you can issue command "lsusb" as it was suggested before my answer. It's really matter of what do you mean about "not recognized". @Marco Ceppi @Oli @Pitto By "not recognized" I meant that when I plug in a 8 gig flash drive an icon immediately appears on the desktop imdicating that there is a flash drive plugged in and I can click on it and view the files on the flash drive. It also shows up on the "Nautilus" default file manager. When I plug in the 320 gig Toshiba external hard drive, I get no indication on the desktop or the file manager (thus "not recogized"). When I run the command cat/proc/partitions/ I get an error message Could not open location 'file:///home/bob/cat/proc/partitions' with or without the external hard drive installed. With the dmeg command I get about 10 pages of info with no mention of disk/partition/anything in /proc/partitions. When I run lsusb command I get the following: bob@bob-desktop:~$ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 04b3:3003 IBM Corp. Rapid Access III Keyboard Bus 003 Device 002: ID 04b3:3004 IBM Corp. Media Access Pro Keyboard Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

    Read the article

  • Ubuntu 13.04 boot into black screen, even after installing nvidia drivers, fail at: "Starting Reload cups, upon starting avahi-daemon..."

    - by Elad92
    I got a new machine with i7 4770k and gefore gtx660. I installed windows and then installed Ubuntu 13.04. In the installation everything went well, after the installation I again boot from the USB and choose try ubuntu, and installed boot-repair because windows automatically boot with no option for ubuntu. After I repaired the boot, I restarted and got into grub, when I chose Ubuntu I got message saying I'm running on low graphics mode and when I pressed ok the screen turned off. I couldn't do anything so I restarted and after reading this post: My computer boots to a black screen, what options do I have to fix it? I got into recovery, selected dpkg and repaired packages. Then I rebooted, and tried to press 'e' and change quiet splash to no splash and nomodeset but unfortunately both of them didn't work, and not the screen didn't get turned off, but I just saw a blank screen. So I rebooted again, entered the recovery, and this time I went to the root shell, and tried to install nvidia drivers from this guide here: http://www.howopensource.com/2012/10/install-nvidia-geforce-driver-in-ubuntu-12-10-12-04-using-ppa/ I rebooted and got the same black screen again (the screen didn't go off, just saw a blank screen). In the grub I see that the kernel is 3.8.0-25. I also checked that the usb files are not corrupted using the check CD from the ubuntu installation screen. I'm really frustrated, I don't know what else can I do. (If someone also knows how can I connect to wifi using the root shell it will be very appreciated, because when I choose the 'enable networking' it again booting me to a black screen. Thanks Edit After digging more, I again boot with nomodeset and saw where is it failing, this is the lines I saw: * Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated [OK] * Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated [fail] I searched for it in google and this is the closest result I got: http://ubuntuforums.org/showthread.php?t=2144261 i didn't find any way to solve it in the internet, from what I understand this is a problem with 13.04. If someone knows how to fix it I will be very grateful. Thanks Edit 2 - 23.6.13 As Mitch suggested, I disabled the avahi-daemon, and when I boot in nomodeset I get the following error: What else can be the problem?

    Read the article

  • WiFi connected to router, but no internet connection

    - by Quetzacotl
    I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

    Read the article

  • HDMI sound gone, can't figure out how to turn it back on

    - by Oli
    I have had an Acer Revo box as a media centre for a while. I recently installed Ubuntu Server (10.10) on it and polished it up with nodm (one of the most simple ways to launch an X session) and installed boxee. It's been working fine for over a month. It's just running ALSA. I've had problems with PulseAudio/Boxee/HDMI before so I wanted to keep it simple. And that worked. It pushed both PCM and digital (AAC and various Dolby codecs) over HDMI perfectly. But I restarted it the other day after mucking around with some nfs configuration and now there isn't any sound. The hardware is an ION chipset. Nvidia 9400M graphics with Nvidia MCP79/7A audio. One thing I have noticed is there doesn't appear to be any sign of a IEC958 device. A traditional fix in the past for fresh installs has been to load alsamixer, find the IEC device and toggle its mute but I can't. I'm certain this used to represent the HDMI output. It just doesn't seem to exist any more unless I run sudo alsa-utils restart while boxee is running, when I see it in an error message: * Shutting down ALSA... [ OK ] * Setting up ALSA... * warning: 'alsactl restore' failed with error message 'alsactl: set_control:1388: Cannot write control '2:0:0:IEC958 Playback Default:0' : Operation not permitted'... ...done. When nodm (and thus boxee) aren't running, I don't see this error but alsamixer still doesn't show the IEC channel. aplay -l gives: card 0: NVidia [HDA NVidia], device 0: ALC662 rev1 Analog [ALC662 rev1 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 0/1 Subdevice #0: subdevice #0 Its section in lshw reads: *-multimedia description: Audio device product: MCP79 High Definition Audio vendor: nVidia Corporation physical id: 8 bus info: pci@0000:00:08.0 version: b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list configuration: driver=HDA Intel latency=0 maxlatency=5 mingnt=2 resources: irq:22 memory:fae78000-fae7bfff I was running on the stock PAE kernel but now it's running on 2.6.37.1. I upgraded to see if that fixed things; it didn't. I'm considering a reinstall but I hate doing that because a) there's a bit of custom configuration in getting X and Boxee to start on boot and b) I don't know what the problem is. If I reinstall this time, I'll end up doing that every time the sound breaks. I love Ubuntu but I don't want to install it once a month. Is there any way to forcibly reset all alsa settings and restart from scratch (without doing a reinstall)? Any other tips? If you need more information, just ask.

    Read the article

  • How to recognize an optimus laptop?

    - by kellogs
    kellogs@kellogs-K52Jc ~ $ lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 80) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 80) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 80) 03:00.4 System peripheral: JMicron Technology Corp. xD Host Controller (rev 80) 03:00.5 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 03) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) kellogs@kellogs-K52Jc ~ $ inxi -SGx System: Host: kellogs-K52Jc Kernel: 3.5.0-17-generic x86_64 (64 bit, gcc: 4.7.2) Desktop: KDE 4.9.5 (Qt 4.8.3) Distro: Linux Mint 14 Nadia Graphics: Card: Intel Core Processor Integrated Graphics Controller bus-ID: 00:02.0 X.Org: 1.13.0 drivers: intel (unloaded: fbdev,vesa) Resolution: [email protected] GLX Renderer: Mesa DRI Intel Ironlake Mobile GLX Version: 2.1 Mesa 9.0.3 Direct Rendering: Yes kellogs@kellogs-K52Jc ~ $ lshw [...] *-display description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 18 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:d0000000-d03fffff memory:c0000000-cfffffff ioport:e080(size=8) Manufacturer advertises the K52Jc model which I bought as optimus enabled. However, no traces of it in the output above. Of course, Bumblebee would not start on this machine. Should I rest assured that is a defective / un-optimused machine ?

    Read the article

  • Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

    - by Donal
    I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

    Read the article

  • Fraud and Anomaly Detection using Oracle Data Mining YouTube-like Video

    - by chberger
    I've created and recorded another YouTube-like presentation and "live" demos of Oracle Advanced Analytics Option, this time focusing on Fraud and Anomaly Detection using Oracle Data Mining.  [Note:  It is a large MP4 file that will open and play in place.  The sound quality is weak so you may need to turn up the volume.] Data is your most valuable asset. It represents the entire history of your organization and its interactions with your customers.  Predictive analytics leverages data to discover patterns, relationships and to help you even make informed predictions.   Oracle Data Mining (ODM) automatically discovers relationships hidden in data.  Predictive models and insights discovered with ODM address business problems such as:  predicting customer behavior, detecting fraud, analyzing market baskets, profiling and loyalty.  Oracle Data Mining, part of the Oracle Advanced Analytics (OAA) Option to the Oracle Database EE, embeds 12 high performance data mining algorithms in the SQL kernel of the Oracle Database. This eliminates data movement, delivers scalability and maintains security.  But, how do you find these very important needles or possibly fraudulent transactions and huge haystacks of data? Oracle Data Mining’s 1 Class Support Vector Machine algorithm is specifically designed to identify rare or anomalous records.  Oracle Data Mining's 1-Class SVM anomaly detection algorithm trains on what it believes to be considered “normal” records, build a descriptive and predictive model which can then be used to flags records that, on a multi-dimensional basis, appear to not fit in--or be different.  Combined with clustering techniques to sort transactions into more homogeneous sub-populations for more focused anomaly detection analysis and Oracle Business Intelligence, Enterprise Applications and/or real-time environments to "deploy" fraud detection, Oracle Data Mining delivers a powerful advanced analytical platform for solving important problems.  With OAA/ODM you can find suspicious expense report submissions, flag non-compliant tax submissions, fight fraud in healthcare claims and save huge amounts of money in fraudulent claims  and abuse.   This presentation and several brief demos will show Oracle Data Mining's fraud and anomaly detection capabilities.  

    Read the article

  • Can't update Nvidia driver and having error near the end of the installation

    - by user94843
    I had just got Ubuntu (first timer to Ubuntu so be very descriptive). I think there a problem with my Nvida update it won't let me update it. This is the name of the update in update manager NVIDIA binary xorg driver, kernel module and VDPAU library. When i attempt to install it, it starts out fine but near the end i get a window titaled package operation failed with these under the details installArchives() failed: Setting up nvidia-current (295.40-0ubuntu1) ... update-initramfs: deferring update (trigger activated) INFO:Enable nvidia-current DEBUG:Parsing /usr/share/nvidia-common/quirks/put_your_quirks_here DEBUG:Parsing /usr/share/nvidia-common/quirks/dell_latitude DEBUG:Parsing /usr/share/nvidia-common/quirks/lenovo_thinkpad DEBUG:Processing quirk Latitude E6530 DEBUG:Failure to match Gigabyte Technology Co., Ltd. with Dell Inc. DEBUG:Quirk doesn't match DEBUG:Processing quirk ThinkPad T420s DEBUG:Failure to match Gigabyte Technology Co., Ltd. with LENOVO DEBUG:Quirk doesn't match Removing old nvidia-current-295.40 DKMS files... Loading new nvidia-current-295.40 DKMS files... Error! DKMS tree already contains: nvidia-current-295.40 You cannot add the same module/version combo more than once. dpkg: error processing nvidia-current (--configure): subprocess installed post-installation script returned error exit status 3 Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.2.0-31-generic Warning: No support for locale: en_US.utf8 Errors were encountered while processing: nvidia-current Error in function: Setting up nvidia-current (295.40-0ubuntu1) ... update-initramfs: deferring update (trigger activated) INFO:Enable nvidia-current DEBUG:Parsing /usr/share/nvidia-common/quirks/put_your_quirks_here DEBUG:Parsing /usr/share/nvidia-common/quirks/dell_latitude DEBUG:Parsing /usr/share/nvidia-common/quirks/lenovo_thinkpad DEBUG:Processing quirk Latitude E6530 DEBUG:Failure to match Gigabyte Technology Co., Ltd. with Dell Inc. DEBUG:Quirk doesn't match DEBUG:Processing quirk ThinkPad T420s DEBUG:Failure to match Gigabyte Technology Co., Ltd. with LENOVO DEBUG:Quirk doesn't match Removing old nvidia-current-295.40 DKMS files... Loading new nvidia-current-295.40 DKMS files... Error! DKMS tree already contains: nvidia-current-295.40 You cannot add the same module/version combo more than once. dpkg: error processing nvidia-current (--configure): subprocess installed post-installation script returned error exit status 3 Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.2.0-31-generic Warning: No support for locale: en_US.utf8

    Read the article

  • Live CD has black screen HP DV6

    - by Shaun Killingbeck
    Attempting to install/try ubuntu (11.10, 12.04) on my new laptop, using a liveCD (and tried USB). I get the purple screen (with the man/keyboard at the bottom) and after that the screen flashes bright white before going black. Ubuntu continues to load in the background, with login sound etc but the screen is off. I have tried as many different solutions as I could find including: using nomodestep, xforcevesa, i915.modeset=0, and also now i915.modeset=1 in boot options (seperately): varying consequences, but either I end up at a blinking cursor with no prompt, a command line (startx fails: no screen found), or the original blank screen again Tried booting from VirtualBox - it crashes at the same place the screen would go blank when using a CD/USB tried 11.04: I don't have this problem BUT when trying to install, I get a ubi-partman error 141 (possibly down to the three partitions that came on my laptop... not sure why HP needed there own separate partition for HP Tools...) Model: HP Pavillion DV6 6B08SA Processor: AMD Quad-Core A6-3410MX APU with Radeon HD 6545G2 Dual Graphics (1.6 GHZ 4 MB L2 cache ) Chipset: AMD RS880M Any help would be greatly appreciated. I just want to be able to partition the drive and install Ubuntu. I'm assuming the issue is graphics card related, although I have no confirmation of that. Update: Tried the ?orkarounds on https://wiki.ubuntu.com/X/Troubleshooting/BlankScreen - set gfxpayload=text changed nothing, removing splash did nothing and setting vesafb.nonsense=1 did nothing either. I'd like to be able to collect some log information somehow, but I can't get to a command line from the liveCD. tried using the latest 12.04 beta, same issue tried nomodeset without splash or quiet. get the following (tail of) output before it freezes on that screen: * Starting configure network device security [OK] * Starting configure network device [OK] [ 25.720899] ieee80211 phy0: w1_ops_config: change monitor mode: false (implement) [ 25.720923] ieee80211 phy0: w1_ops_config: change power-save mode: false (implement) * Starting restore sound card(s') mixer state(s) [fail] [ 25.721849] ieee80211 phy0: w1_ops_bss_info_changed: qos enabled: false (implement) * Stopping save kernel messages [OK] * Starting bluetooth [OK] * PulseAudio configured for per-user sessions saned disabled; edit /etc/default/saned [ 25.988016] hci_cmd_timer: hci0 command tx timeout [ 26.207225] bad LUN (0:1) [ 26.223735] bad target number (1:0) [ 26.252111] bad target number (2:0) [ 26.272170] bad target number (3:0) [ 26.300154] bad target number (4:0) [ 26.328162] bad target number (5:0) [ 26.344180] bad target number (6:0) [ 26.368142] bad target number (7:0) * Checking battery state... [OK] * Stopping System V runlevel capability [OK] Does this give any indication of the problem? the false (implement) messages also reappear when I press the power button to ask it to shutdown, followed by a [fail] status for killing remaining processes.

    Read the article

  • How do I stop icons appearing on the desktop under conky?

    - by Seamus
    When I download something to my desktop, or insert a CD or flash drive, the icon appears on my desktop. When I have conky running, the icon sometimes appears in the top right corner, underneath conky; where I can't see it. How do I stop this happening? My .conkyrc is pasted below. I didn't write it all myself, so I'm not entirely sure what I need to change, or what parts are relevant for this particular question... # UBUNTU-CONKY # A comprehensive conky script, configured for use on # Ubuntu / Debian Gnome, without the need for any external scripts. # # Based on conky-jc and the default .conkyrc. # INCLUDES: # - tail of /var/log/messages # - netstat shows number of connections from your computer and application/PID making it. Kill spyware! # # -- Pengo # # Create own window instead of using desktop (required in nautilus) own_window yes own_window_type override own_window_transparent yes own_window_hints undecorated,below,sticky,skip_taskbar,skip_pager # Use double buffering (reduces flicker, may not work for everyone) double_buffer yes # fiddle with window use_spacer right # Use Xft? use_xft yes xftfont DejaVu Sans:size=8 xftalpha 0.8 text_buffer_size 2048 # Update interval in seconds update_interval 3.0 # Minimum size of text area # minimum_size 250 5 # Draw shades? draw_shades no # Text stuff draw_outline no # amplifies text if yes draw_borders no uppercase no # set to yes if you want all text to be in uppercase # Stippled borders? stippled_borders 3 # border margins border_margin 9 # border width border_width 10 # Default colors and also border colors, grey90 == #e5e5e5 default_color grey own_window_colour brown own_window_transparent yes # Text alignment, other possible values are commented #alignment top_left alignment top_right #alignment bottom_left #alignment bottom_right # Gap between borders of screen and text gap_x 10 gap_y 20 # stuff after 'TEXT' will be formatted on screen TEXT $color ${color orange}SYSTEM ${hr 2}$color $nodename $sysname $kernel on $machine ${color orange}CPU ${hr 2}$color ${freq}MHz Load: ${loadavg} Temp: ${acpitemp} $cpubar ${cpugraph 000000 ffffff} NAME ${goto 150}PID ${goto 200}CPU% ${goto 250}MEM% ${top name 1} ${goto 150}${top pid 1} ${goto 200}${top cpu 1} ${goto 250}${top mem 1} ${top name 2} ${goto 150}${top pid 2} ${goto 200}${top cpu 2} ${goto 250}${top mem 2} ${top name 3} ${goto 150}${top pid 3} ${goto 200}${top cpu 3} ${goto 250}${top mem 3} ${top name 4} ${goto 150}${top pid 4} ${goto 200}${top cpu 4} ${goto 250}${top mem 4} ${color orange}MEMORY / DISK ${hr 2}$color RAM: $memperc% ${membar 6}$color Swap: $swapperc% ${swapbar 6}$color Home: ${fs_free_perc /home}% ${fs_bar 6 /}$color Free Space: ${fs_free /home} ${color orange}NETWORK (${addr eth0}) ${hr 2}$color Down: $color${downspeed eth0} k/s ${alignr}Up: ${upspeed eth0} k/s ${downspeedgraph eth0 25,140 000000 ff0000} ${alignr}${upspeedgraph eth0 25,140 000000 00ff00}$color Total: ${totaldown eth0} ${alignr}Total: ${totalup eth0} ${execi 30 netstat -ept | grep ESTAB | awk '{print $9}' | cut -d: -f1 | sort | uniq -c | sort -nr} ${color orange}WIRELESS (${addr wlan0}) ${hr 2}$color Down: $color${downspeed wlan0} k/s ${alignr}Up: ${upspeed wlan0} k/s ${downspeedgraph wlan0 25,140 000000 ff0000} ${alignr}${upspeedgraph wlan0 25,140 000000 00ff00}$color Total: ${totaldown wlan0} ${alignr}Total: ${totalup wlan0} ${execi 30 netstat -ept | grep ESTAB | awk '{print $9}' | cut -d: -f1 | sort | uniq -c | sort -nr}

    Read the article

  • Ubuntu hangs on booting up after a update

    - by alFReD NSH
    I've made a clean install yesterday, for the first time restarted, everything went good and then after I updated packages and copied my old home directory to replace the new one, when I restarted it hung when it was booting. I tried reinstalling again and doing the same thing, but again same thing happened. Here's what I see, before when the Ubuntu logo with the five dots is shown: Then after that, 3 or 4 of the dots will load and hangs there. If I press arrow up before that, this will be shown I started my laptop again today(the pictures are for the day before) and after that, boot up with live CD and got the logs. dmesg: http://pastebin.com/aVxV7BQF syslog: http://pastebin.com/4E2BrRUK And some info: alfred@alFitop:~$ uname -a Linux alFitop 3.2.0-24-generic #39-Ubuntu SMP Mon May 21 16:52:17 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lshw: http://pastebin.com/AZbKJmsT sources.list : http://pastebin.com/2HazmuyV My problem is a bit similar to here: http://ubuntuforums.org/showthread.php?t=1918271 Though I didn't change my x.org config. Only changed home directory and updated packages. I've tried memtest and fschk, both passed. In the recovery mode boot option, I've also realized that same things happen in failsafe graphical mode. But when I go into the network mode, I can boot up my system, but of course same the graphics are just basic. Adding blacklist intel_ips to /etc/modprobe.d/blacklist.conf solves the first message, but still I get the broken pipe and CPU stack traces. The current kernel version is 3.2.0-25, I've tried booting up in the 3.2.0-23(the one the installer came with, but same results.) Also uninstalled apparmor, didn't help. I've installed Ubuntu again, this time without copying the home directory, also same result. --- UPDATE --- This problem was solved before with removing backports, but its back again! I've updated my laptop last night and the problem came back. It's definitely one of these packages. My /var/log/apt/term.log and /var/log/apt/history.log. I'm almost having the same situation. --- UPDATE --- I realized this also have happened on times that I have updated(haven't restarted after it) and my computer power has been cut off and its shutdown due to lack of power. And I realized if I just do as I answered but not in somewhere without GUI(networking mode has the GUI) it wouldn't work.

    Read the article

  • can't update nvida having error near the end of the install

    - by user94843
    I had just got Ubuntu (first timer to Ubuntu so be very descriptive). I think there a problem with my Nvida update it won't let me update it. This is the name of the update in update manager NVIDIA binary xorg driver, kernel module and VDPAU library. When i attempt to install it, it starts out fine but near the end i get a window titaled package operation failed with these under the details installArchives() failed: Setting up nvidia-current (295.40-0ubuntu1) ... update-initramfs: deferring update (trigger activated) INFO:Enable nvidia-current DEBUG:Parsing /usr/share/nvidia-common/quirks/put_your_quirks_here DEBUG:Parsing /usr/share/nvidia-common/quirks/dell_latitude DEBUG:Parsing /usr/share/nvidia-common/quirks/lenovo_thinkpad DEBUG:Processing quirk Latitude E6530 DEBUG:Failure to match Gigabyte Technology Co., Ltd. with Dell Inc. DEBUG:Quirk doesn't match DEBUG:Processing quirk ThinkPad T420s DEBUG:Failure to match Gigabyte Technology Co., Ltd. with LENOVO DEBUG:Quirk doesn't match Removing old nvidia-current-295.40 DKMS files... Loading new nvidia-current-295.40 DKMS files... Error! DKMS tree already contains: nvidia-current-295.40 You cannot add the same module/version combo more than once. dpkg: error processing nvidia-current (--configure): subprocess installed post-installation script returned error exit status 3 Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.2.0-31-generic Warning: No support for locale: en_US.utf8 Errors were encountered while processing: nvidia-current Error in function: Setting up nvidia-current (295.40-0ubuntu1) ... update-initramfs: deferring update (trigger activated) INFO:Enable nvidia-current DEBUG:Parsing /usr/share/nvidia-common/quirks/put_your_quirks_here DEBUG:Parsing /usr/share/nvidia-common/quirks/dell_latitude DEBUG:Parsing /usr/share/nvidia-common/quirks/lenovo_thinkpad DEBUG:Processing quirk Latitude E6530 DEBUG:Failure to match Gigabyte Technology Co., Ltd. with Dell Inc. DEBUG:Quirk doesn't match DEBUG:Processing quirk ThinkPad T420s DEBUG:Failure to match Gigabyte Technology Co., Ltd. with LENOVO DEBUG:Quirk doesn't match Removing old nvidia-current-295.40 DKMS files... Loading new nvidia-current-295.40 DKMS files... Error! DKMS tree already contains: nvidia-current-295.40 You cannot add the same module/version combo more than once. dpkg: error processing nvidia-current (--configure): subprocess installed post-installation script returned error exit status 3 Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.2.0-31-generic Warning: No support for locale: en_US.utf8

    Read the article

  • nvidia optimus laptops

    - by kellogs
    kellogs@kellogs-K52Jc ~ $ lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 80) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 80) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 80) 03:00.4 System peripheral: JMicron Technology Corp. xD Host Controller (rev 80) 03:00.5 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 03) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) kellogs@kellogs-K52Jc ~ $ inxi -SGx System: Host: kellogs-K52Jc Kernel: 3.5.0-17-generic x86_64 (64 bit, gcc: 4.7.2) Desktop: KDE 4.9.5 (Qt 4.8.3) Distro: Linux Mint 14 Nadia Graphics: Card: Intel Core Processor Integrated Graphics Controller bus-ID: 00:02.0 X.Org: 1.13.0 drivers: intel (unloaded: fbdev,vesa) Resolution: [email protected] GLX Renderer: Mesa DRI Intel Ironlake Mobile GLX Version: 2.1 Mesa 9.0.3 Direct Rendering: Yes Manufacturer advertises the K52Jc model which I bought as optimus enabled. However, no traces of it in the output above. Of course, Bumblebee would not start on this machine. Should I rest assured that is a defective / un-optimused machine ? thanks

    Read the article

  • Where I missed boot.properties.?

    - by Dyade, Shailesh M
    Today one of my customer was trying to start the WebLogic Server ( Production Instance) , though he was trying to start the server in a standard way, but it was failing due to below error :   ####<Oct 22, 2012 12:14:43 PM BST> <Warning> <Security> <BanifB1> <> <main> <> <> <> <1350904483998> <BEA-090066> <Problem handling boot identity. The following exception was generated: weblogic.security.internal.encryption.EncryptionServiceException: weblogic.security.internal.encryption.EncryptionServiceException: [Security:090219]Error decrypting Secret Key java.security.ProviderException: setSeed() failed> And it started failing into below causes. ####<Oct 22, 2012 12:16:45 PM BST> <Critical> <WebLogicServer> <BanifB1> <AdminServer> <main> <<WLS Kernel>> <> <> <1350904605837> <BEA-000386> <Server subsystem failed. Reason: java.lang.AssertionError: java.lang.reflect.InvocationTargetException java.lang.AssertionError: java.lang.reflect.InvocationTargetException weblogic.security.internal.encryption.EncryptionServiceException: weblogic.security.internal.encryption.EncryptionServiceException: [Security:090219]Error decrypting Secret Key java.security.ProviderException: setSeed() failed weblogic.security.internal.encryption.EncryptionServiceException: [Security:090219]Error decrypting Secret Key java.security.ProviderException: setSeed() failed at weblogic.security.internal.encryption.JSafeSecretKeyEncryptor.decryptSecretKey(JSafeSecretKeyEncryptor.java:121) Customer was facing this issue without any changes in the system, it was stable suddenly started seeing this issue last night. When we checked, customer was manually entering the username and password, config.xml had the entries encrypted However when verified, customer had the boot.properties at the Servers/AdminServer/security folder and DomainName/security didn't have this file. Adding boot.properies fixed the issue. Regards Shailesh Dyade 

    Read the article

  • Why does the login screen fail to appear?

    - by a different ben
    My system: Dell Precision T3500 nVidia Quadro NVS 295 Ubuntu 12.04 x86_64 (3.2.0-32) Essential problem: On boot my system won't get past the splash screen. I can switch to another virtual terminal and log in, I can also ssh from another system -- so it appears that the problem might be with the display manager. How can I diagnose and fix this problem? More info: From a VT I can issue sudo lightdm restart, and this will bring up the login screen and and I can continue from there. So I do have access to my system. Update-manager recently updated a number of packages, including a bunch of x11 and xorg packages, some nVidia drivers, rpcbind, etc etc. My boot log (if that is any guidance) says the following: fsck from util-linux 2.20.1 fsck from util-linux 2.20.1 fsck from util-linux 2.20.1 fsck from util-linux 2.20.1 rpcbind: Cannot open '/run/rpcbind/rpcbind.xdr' file for reading, errno 2 (No such file or directory) rpcbind: Cannot open '/run/rpcbind/portmap.xdr' file for reading, errno 2 (No such file or directory) /dev/sda1: clean, 597650/1525920 files, 3963433/6103296 blocks /dev/sda7: clean, 11/6406144 files, 450097/25608703 blocks /dev/sda5: clean, 158323/1525920 files, 1886918/6103296 blocks /dev/sda8: clean, 250089/107929600 files, 111088810/431689728 blocks Skipping profile in /etc/apparmor.d/disable: usr.bin.firefox Skipping profile in /etc/apparmor.d/disable: usr.sbin.rsyslogd * Starting AppArmor profiles [80G [74G[ OK ] Loading the saved-state of the serial devices... /dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A * Starting ClamAV virus database updater freshclam [80G [74G[ OK ] * Starting Name Service Cache Daemon nscd [80G [74G[ OK ] * Starting modem connection manager[74G[ OK ] * Starting K Display Manager[74G[ OK ] * Starting mDNS/DNS-SD daemon[74G[ OK ] * Stopping GNOME Display Manager[74G[ OK ] * Stopping K Display Manager[74G[ OK ] * Starting bluetooth daemon[74G[ OK ] * Starting network connection manager[74G[ OK ] * Starting Postfix Mail Transport Agent postfix [80G [74G[ OK ] speech-dispatcher disabled; edit /etc/default/speech-dispatcher * Starting VirtualBox kernel modules [80G [74G[ OK ] * Starting the Winbind daemon winbind [80G [74G[ OK ] saned disabled; edit /etc/default/saned * Starting anac(h)ronistic cron[74G[ OK ] * Stopping anac(h)ronistic cron[74G[ OK ] * Checking battery state... [80G [74G[ OK ] nxsensor is disabled in '/usr/NX/etc/node.cfg' Trying to start NX server: NX 122 Service started. NX 999 Bye. Trying to start NX statistics: NX 723 Cannot start NX statistics: NX 709 NX statistics are disabled for this server. NX 999 Bye. * Stopping System V runlevel compatibility[74G[ OK ] * Starting Mount network filesystems[74G[ OK ] * Stopping Mount network filesystems[74G[ OK ] * Stopping regular background program processing daemon[74G[ OK ] * Starting regular background program processing daemon[74G[ OK ] * Starting anac(h)ronistic cron[74G[ OK ] * Stopping anac(h)ronistic cron[74G[ OK ]

    Read the article

  • ssao implementation

    - by Irbis
    I try to implement a ssao based on this tutorial: link I use a deferred rendering and world coordinates for shading calculations. When saving gbuffer a vertex shader output looks like this: worldPosition = vec3(ModelMatrix * vec4(inPosition, 1.0)); normal = normalize(normalModelMatrix * inNormal); gl_Position = ProjectionMatrix * ViewMatrix * ModelMatrix * vec4(inPosition, 1.0); Next for a ssao calculations I render a scene as a full screen quad and I save an occlusion parameter in a texture. (Vertex positions in the world space: link Normals in the world space: link) SSAO implementation: subroutine (RenderPassType) void ssao() { vec2 texCoord = CalcTexCoord(); vec3 worldPos = texture(texture0, texCoord).xyz; vec3 normal = normalize(texture(texture1, texCoord).xyz); vec2 noiseScale = vec2(screenSize.x / 4, screenSize.y / 4); vec3 rvec = texture(texture2, texCoord * noiseScale).xyz; vec3 tangent = normalize(rvec - normal * dot(rvec, normal)); vec3 bitangent = cross(normal, tangent); mat3 tbn = mat3(tangent, bitangent, normal); float occlusion = 0.0; float radius = 4.0; for (int i = 0; i < kernelSize; ++i) { vec3 pix = tbn * kernel[i]; pix = pix * radius + worldPos; vec4 offset = vec4(pix, 1.0); offset = ProjectionMatrix * ViewMatrix * offset; offset.xy /= offset.w; offset.xy = offset.xy * 0.5 + 0.5; float sample_depth = texture(texture0, offset.xy).z; float range_check = abs(worldPos.z - sample_depth) < radius ? 1.0 : 0.0; occlusion += (sample_depth <= pix.z ? 1.0 : 0.0); } outputColor = vec4(occlusion, occlusion, occlusion, 1); } That code gives following results: camera looking towards -z world space: link camera looking towards +z world space: link I wonder if it is possible to use world coordinates in the above code ? When I move camera I get different results because world space positions don't change. Can I treat worldPos.z as a linear depth ? What should I change to get a correct results ? I except the white areas in place of occlusion, so the ground should has the white areas only near to the object.

    Read the article

  • Ubuntu 10.10 not recognizing external hard drive

    - by sr71
    Installed Ubuntu 10.10 on a hard drive by itself (no windows). All updates are up to date. Everything`works fine except when I plug in a 320 gig Toshiba external hard drive....it is not recognized. When I plug in an 8 gig flash drive it is recognized no problem. What do I mean by "not recognized"? I mean: how do you know it was not recognized. You can check the command "cat /proc/partitions" in a terminal with and without the hdd attached. If you see some difference, it's ok. If the difference is something like "sda1" (sd+letter+number) then you have partition on it, maybe it can't be handled in Ubuntu (no filesystem on it or so). If there is only "sda" in the difference for example (sd+letter, but no number after it) then the drive itself is detected, just no partition is created on it. Also you can check out the messages of the kernel, with the "dmesg" command in the terminal. If there is no disk/partition/anything in /proc/partitions, there can be an USB level problem, you can issue command "lsusb" as it was suggested before my answer. It's really matter of what do you mean about "not recognized". @Marco Ceppi @Oli @Pitto By "not recognized" I meant that when I plug in a 8 gig flash drive an icon immediately appears on the desktop imdicating that there is a flash drive plugged in and I can click on it and view the files on the flash drive. It also shows up on the "Nautilus" default file manager. When I plug in the 320 gig Toshiba external hard drive, I get no indication on the desktop or the file manager (thus "not recogized"). When I run the command "cat/proc/partitions/" I get an error message Could not open location 'file:///home/bob/cat/proc/partitions' with or without the external hard drive installed. With the "dmeg" command I get about 10 pages of info with no mention of disk/partition/anything in /proc/partitions. When I run "lsub" command I get the following: bob@bob-desktop:~$ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 04b3:3003 IBM Corp. Rapid Access III Keyboard Bus 003 Device 002: ID 04b3:3004 IBM Corp. Media Access Pro Keyboard Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub bob@bob-desktop:~$

    Read the article

  • How do I set image position in conky

    - by realitygenerator
    I copied and modified an existing .conkyrc file from the ubuntu forum and I'm trying to place the LinuxMint logo in a specific position Below are my conkyrc file and the screenshot # UBUNTU-CONKY # A comprehensive conky script, configured for use on # Ubuntu / Debian Gnome, without the need for any external scripts. # # Based on conky-jc and the default .conkyrc. # INCLUDES: # - tail of /var/log/messages # - netstat shows number of connections from your computer and application/PID making it. Kill spyware! # # -- Pengo # # Create own window instead of using desktop (required in nautilus) own_window yes own_window_type desktop own_window_transparent yes own_window_hints undecorated,below,sticky,skip_taskbar,skip_pager # Use double buffering (reduces flicker, may not work for everyone) double_buffer yes # fiddle with window use_spacer right # Use Xft? use_xft yes xftfont URW Gothic:size=8 xftalpha 0.8 text_buffer_size 2048 # Update interval in seconds update_interval 3.0 # Minimum size of text area # minimum_size 250 5 # Draw shades? draw_shades no # Text stuff draw_outline no # amplifies text if yes draw_borders no uppercase no # set to yes if you want all text to be in uppercase # Stippled borders? stippled_borders 3 # border margins border_margin 9 # border width border_width 10 # Default colors and also border colors, grey90 == #e5e5e5 default_color grey own_window_colour brown own_window_transparent yes # Text alignment, other possible values are commented #alignment top_left #alignment top_right #alignment bottom_left #alignment bottom_right. alignment top_middle # Gap between borders of screen and text gap_x 10 gap_y 10 #Display temp in fahrenheit temperature_unit fahrenheit #Choose which screen on which to display # stuff after 'TEXT' will be formatted on screen TEXT $color ${color green}SYSTEM ${hr 2}$color $nodename $sysname $kernel on $machine LinuxMint 11 "Katya" (Oneric) ${image ~/Conky/Logo_Linux_Mint.png -s 80x60 -f 86400} ${color green}CPU ${hr 2}$color ${freq}MHz Load: ${loadavg} Temp: ${hwmon temp 1} $cpubar ${cpugraph 000000 ffffff} NAME PID CPU% MEM% ${top name 1} ${top pid 1} ${top cpu 1} ${top mem 1} ${top name 2} ${top pid 2} ${top cpu 2} ${top mem 2} ${top name 3} ${top pid 3} ${top cpu 3} ${top mem 3} ${top name 4} ${top pid 4} ${top cpu 4} ${top mem 4} ${color green}MEMORY / DISK ${hr 2}$color RAM: $memperc% ${membar 6}$color Swap: $swapperc% ${swapbar 6}$color Root: ${fs_free_perc /}% ${fs_bar 6 /}$color hda1: ${fs_free_perc /media/sda1}% ${fs_bar 6 /media/sda1}$color ${color green}NETWORK (${addr eth1}) ${hr 2}$color Down: $color${downspeed eth1} k/s ${alignr}Up: ${upspeed eth1} k/s ${downspeedgraph eth1 25,140 000000 ff0000} ${alignr}${upspeedgraph eth1 25,140 000000 00ff00}$color Total: ${totaldown eth1} ${alignr}Total: ${totalup eth1} ${execi 30 netstat -ept | grep ESTAB | awk '{print $9}' | cut -d: -f1 | sort | uniq -c | sort -nr} ${color green}LOGGING ${hr 2}$color ${execi 30 tail -n3 /var/log/messages | awk '{print " ",$5,$6,$7,$8,$9,$10}' | fold -w50} ${color green}FORTUNE ${hr 2}$color ${execi 120 fortune -s | fold -w50} I want to put the mint logo right after the word (oneric). Any help would be greatly appreciated.

    Read the article

  • How can I optimize Apache to use 1GB of RAM on my website? [closed]

    - by Markon
    My VPS plan gives me 1GB of RAM burstable to 2GB. Of course I cannot use 2 GB, nor 1 GB, everyday, so I'm planning to optimize the performance of my webserver. The average of hits-per-hour is about 8'000-10'000. This means about 2 connections-per-second. Max hits-per-hour reached until now is about 60'000. That means about 16 connections-per-second. Unluckily my current apache configuration uses too much memory (when there are not connected clients - usually during the night - it uses about 1GB) so I've tried to customize the apache installation to fit to my needs. I'm using Ubuntu, kernel 2.6.18, with apache2-mpm-worker, since I've read it requires less memory, and fcgid ( + PHP). This is my /etc/apache2/apache2.conf: Timeout 45 KeepAlive on MaxKeepAliveRequests 100 KeepAliveTimeout 10 <IfModule mpm_worker_module> StartServer 2 MinSpareThreads 25 MaxSpareThreads 75 MaxClients 100 MaxRequestsPerChild 0 </IfModule> This is the output of ps aux: www-data 9547 0.0 0.3 423828 7268 ? Sl 20:09 0:00 /usr/sbin/apache2 -k start root 17714 0.0 0.1 76496 3712 ? Ss Feb05 0:00 /usr/sbin/apache2 -k start www-data 17716 0.0 0.0 75560 2048 ? S Feb05 0:00 /usr/sbin/apache2 -k start www-data 17746 0.0 0.1 76228 2384 ? S Feb05 0:00 /usr/sbin/apache2 -k start www-data 20126 0.0 0.3 424852 7588 ? Sl 19:24 0:02 /usr/sbin/apache2 -k start www-data 24260 0.0 0.3 424852 7580 ? Sl 19:42 0:01 /usr/sbin/apache2 -k start while this is ps aux for php5: www-data 7461 2.9 2.2 142172 47048 ? S 19:39 1:39 /usr/lib/cgi-bin/php5 www-data 23845 1.3 1.7 135744 35948 ? S 20:17 0:15 /usr/lib/cgi-bin/php5 www-data 23900 2.0 1.7 136692 36760 ? S 20:17 0:22 /usr/lib/cgi-bin/php5 www-data 27907 2.0 2.0 142272 43432 ? S 20:00 0:43 /usr/lib/cgi-bin/php5 www-data 27909 2.5 1.9 138092 40036 ? S 20:00 0:53 /usr/lib/cgi-bin/php5 www-data 27993 2.4 2.2 142336 47192 ? S 20:01 0:50 /usr/lib/cgi-bin/php5 www-data 27999 1.8 1.4 135932 31100 ? S 20:01 0:38 /usr/lib/cgi-bin/php5 www-data 28230 2.6 1.9 143436 39956 ? S 20:01 0:54 /usr/lib/cgi-bin/php5 www-data 30708 3.1 2.2 142508 46528 ? S 19:44 1:38 /usr/lib/cgi-bin/php5 As you can see it use a lot of memory. How can I reduce it to fit to just 1GB of RAM? PS: I also think about the switch to nginx, if Apache can't fit to my needs...

    Read the article

  • Is there a usage count for packages or programs?

    - by math
    Motivation: I want to remove applications I do not use to speed up my package processing tasks like dist upgrades, regular updates, but also for saving disk space and other reasons. I know this is a complex topic so first I will ask my question and second I will give some answers I already found out. Question: How do I find out which package I did not used at all? For example I always use the VLC so I could remove totem package. (Which I could have been used some day, yes.) Of course package dependencies could force me to have programs installed which I will never use. Notes: Find the packages which consume much space via synaptic: Select "Status" in lower left, select "Installed" in upper left, sort column on "size" in upper right. Then you can decide which big packages you really need. Use aptitude autoremove Use ubuntu-tweak's Janitor for removing old kernel packages, old configs, apt-cache entries, etc. Manually search for applications for a given task that you usually solve with your standard app. E.g. Movie player, Music player, Office program, Browser etc. (BTW: this is what I want to be helped with my question) When removing packages I always favour "apt-get purge" over "aptitude remove --purge" as aptitude often will also remove essential packages due to package dependencies. E.g. when removing "evolution" (as I use thunderbird) aptitude wants to remove also "ubuntu-desktop" and 756 other packages as well, while apt-get just removes evolution and its helping pacakges like evolution-common. Ubuntu lense gives me most recent used applications which are candidates for keeping :) Employ deborphan as I read in this related answer: How do I clean up my harddrive? I should certainly keep essential packages: Keep only essential packages This question is pretty much a duplicate of How to see what installed packages I have never used for cleaning purposes but covering only few aspects. However one answer suggests to use a program called unusedpkg but the link seems down. There is also a program called Kleen http://code.google.com/p/kleen/ but it won't compile in 11.10. However I hacked it to compile but the results are unusable, as for example the g++ package was marked as not used for 203, but actually I used it seconds ago for compiling Kleen itself ;) So don't use this tool. On http://wiki.debian.org/DebianPackageInformation I read the the package popularity-contest will produce log files with usage statistics. Unfortunately I didn't enabled the popularity contest so I can't find this log file.

    Read the article

  • Ubuntu 12.04 x64 LTS VPN Server not changing IP

    - by user288778
    I used this guide http://silverlinux.blogspot.co.uk/2012/05/how-to-pptp-vpn-on-ubuntu-1204-pptpd.html and it worked fine. I'm able to connect but the problem is, that my IP being changed to "localip" not "remote ip". This is what I get from tail -f /var/log/syslog [code] June 6 00:09:19 instant5860 NetworkManager[1456]: Unmanaged Device found; state CONNECTED forced (see http://bugs.launchpad.net/bugs/191889) June 6 00:09:19 instant5860 NetworkManager[1456]: Marking connection 'Wired connection 1' invalid. June 6 00:09:19 instant5860 NetworkManager[1456]: Activation (eth1) failed. June 6 00:09:19 instant5860 NetworkManager[1456]: Activation (eth1) Stage 4 of 5 (IPv4 Configure Timeout) complete. June 6 00:09:19 instant5860 NetworkManager[1456]: (eth1): device state change: failed - disconnected (reason 'none') [120 30 0] June 6 00:09:19 instant5860 NetworkManager[1456]: (eth1): deactivating device (reason 'none') [0] June 6 00:09:19 instant5860 NetworkManager[1456]: Unmanaged Device found; state CONNECTED forced. June----- avahi-daemon[440]: Withdrawing address record for fe80......... on eth1 Jun------avahi-daemon[440]: Leaving mDNS multicast group on interface eth1. IPv6 with address fe80..... Jun------avahi-daemon[440]: Interface eth1.IPv6 no longer relevant for mDNS. Jun------avahi-daemon[440]: Joining mDNS multicast group on interface eth1.IPv6 with address fe80.... Jun------avahi-daemon[440]: New relevant interface eth1.IPv6 for mDNS Jun------avahi-daemon[440]: Registering new address record for fe80..... on eth1.*. Jun - snmpd[1172]: error on subcontainer 'ia_addr' insert (-1) dbusp382]: [syste] Activating service name='org.freedesktop.PackageKit' (using servicehelper) AptDaemon: INFO: Initializing daemon AptDaemon.PackageKit: INFO: Initializing PackageKit compat layer dbus[382]: [system] Successfu;;y activated service 'org.freedesktop.PackageKit' AptDaemon.PackageKit: INFO: Initializing PackageKit transaction AptDaemon.Worker: INFO: Simulating trans: /org/debian/apt/transaction/233beca013a0473ea34d9dea805af5df AptDaemon.Worker: INFO: Processing transaction /org/debian/apt... AptDaemon.PackageKit: INFO: Get updates() AptDaemon.Worker: INFO: Finished snmpd[1172]: error on subcontainer pptpd[23611]: CTRL: Client 82.33.... control connection started pptpd[23611]: CTRL: Starting call (launching pppd, opening GRE) pptpd[23611]: pppd 2.4.5 started by root uid 0 pptpd[23611]: Using interface ppp0 pptpd[23611]: Connect ppp0 <-- /dev/pts/1 NetworkManager[1456]: SCPlugin - Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) NetworkManager[1456]:SCPlugin - Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. pptpd[23612]: peer from calling number 82... authorized. kernel: [2918261.416923] init: ufw pre-start process (23613) terminated with status 1 dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 7 CTRL: Ignored a SET LING info packet with real ACCMs! local IP address:109.0.121.197 remote IP address: 109.0.84.56 dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 13 NetworkManager[1456]: (eth1): DHCPv4 request timed out. NetworkManager[1456]: (eth1): canceled DHCP transaction, DHCP client pid 23280 NetworkManager[1456]: Activation (eth1) Stage 4 of 5 (IPv4 Configure Timeout) scheduled... NetworkManager[1456]: Activation (eth1) Stage 4 of 5 (IPv4 Configure Timeout) started... NetworkManager[1456]: (eth1): device state change: ip-config - failed (reason 'ip-config-unavailable') [70 120 5[ NetworkManager[1456]: Unmanaged 'ia_addr' insert (-1)[/code]

    Read the article

< Previous Page | 518 519 520 521 522 523 524 525 526 527 528 529  | Next Page >