Search Results

Search found 1720 results on 69 pages for 'house hunting'.

Page 53/69 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• How to serve media across home network?

  - by TK Kocheran

  I'm looking to share my media across my home network. Router fully supports running a DLNA server, but I don't know if it'd be better to run the server from my main server computer instead of from the router, as the router would have to operate off of a network share and my server can operate directly off of the files. Here's what I need to serve, in order of importance: ISO 1:1 DVD rips (4-8GB files), MP4/H.264 encoded videos, MKV videos, MP3 files, JPEG/CR2 images. Maybe I'm completely ludicrous for wanting to push full DVD files across my network, but in reality, I would assume that only the parts of the actual file needed (ie: menu, main video payload for main title) would be served at any one time. Plus, encoding takes time and precious disk space, so why not stream it 1:1 ;) Does anyone know of the best way to accomplish this? Main goal is to serve it to Logitech Revue downstairs and secondary goal is to serve it to other computers in the house. For music, I assume I could run a DAAP server, but I don't think that the Revue supports that (and I can't exactly throw together an app that does it just yet).

  Read the article

• Too many concurrent connections Exchange 2010. What else is there to check?

  - by hydroparadise

  I thought that I had this under control before. But for some reason during our last email marketing promo, I start receiving from our mass email client (built in house).. The message could not be sent to the SMTP server. The transport error code is 0x800ccc67. The server repsonse was 421 4.3.2 The maximum number of concurrent connections has exceeded a limit, closing transmission channel again. There's several places I've checked to make sure that wouldn't be an issue. First I checked that receive connector was set to receive an adequate number of connections on our relay connector (1000 connections). Then, I would later find out about Throttling Policies. I created one and set all the properties I knew to set in terms of the policy following properties to 1000; EWSMaxConcurrency, OWAMaxConcurrency, CPAMaxConcurrency, and CPAMaxConcurrency. Still, the email client starts receiving the error shortly after 100 has been sent and takes about 15-30 seconds. The process is then repeatable, but still the error gets received at the same spot everytime. Is there a rate setting that I am missing? Was there a windows update that I missed looking at? Should the software have it's own throttling feature?

  Read the article

• How can I tell my dd-wrt router to use someone's Amazon Affiliates link when I point my browser to amazon.com?

  - by Michael Paul

  Here's what I'd like to do. Instead of a one-time donation to one of my favorite free tools (junecloud.com) I'd like to do what they suggest here and use their Amazon Affiliates link to do all my Amazon shopping. I shop at amazon once or twice a week, so this is a great way to let them earn lots of long-term cash without me dropping a dime. My thought was to go into my dd-wrt enabled router and tell it, "any time I go to amazon.com on any computer in the house, please go to http://www.amazon.com/gp/redirect.html?link_code=ur2&tag=junecloud-20&camp=1789&creative=9325&location=%2F instead. (That URL simply redirects me to amazon.com but every purchase I make during that session is credited to JuneCloud.) Once logged into dd-wrt, I went to Services Services DNSMasq but I'm not really sure how to get it to work from there, or if it's even possible. I know I can redirect IP addresses, but I'm looking to redirect someone on my network from amazon.com to the special amazon affiliate code link. Hope that's clear. Thanks for any replies!

  Read the article

• How can I filter data based on items in a list?

  - by user2964366

  How can I filter entries containing any specific word in a list of words? For example, I have a list of road names in Singapore. Amoy Street, Singapore Ann Siang Hill Anson Road Arab Street Armenian Street, Singapore BBaghdad Street (Singapore) Balestier Road Banda Street Bartley Road Beach Road, Singapore Bencoolen Street Bernam Street Boat Quay Boon Tat Street Boundary Road, Singapore Bras Basah Road Bugis Street Bukit Batok Road Bukit Pasoh Road Bukit Timah Road CCantonment Road, Singapore Choa Chu Kang Road Clarke Quay Clementi Road Club Street Collyer Quay Connaught Drive Craig Road (Singapore) Cross Street and many more My spreadsheet has a large number of entries like the following, which may or may not contain road names mentioned in my list: Saw an accident at Thomson Road Found this by accident 6 vehicles crashed at Balestier Road I wanna crash now. So tired. Bus collides with bicycle at Arab Street. Accident at City Road. You can crash my house later. How do I filter to return entries that contains any road name identified in the list of names? How do I introduce an array/list of road names into Microsoft Excel and then relate it to a filter function?

  Read the article

• SNMP Access on Ubuntu

  - by javano

  I am trying to use SNMP to monitor a machine locally on its self and remotely. This is the snmpd.conf (Ubuntu 8.04.1): # sec.name source comunity com2sec readonly 1.2.3.4 nicenandtight com2sec readonly 5.6.7.8 reallysafe group MyROGroup v1 readonly group MyROGroup v2c readonly group MyROGroup usm readonly view all included .1 view system included .iso.org.dod.internet.mgmt.mib-2.system access MyROGroup "" any noauth exact all none none syslocation my house syscontact me <[email protected]> exec .1.3.6.1.4.1.2021.7890.1 distro /usr/bin/distro smuxpeer .1.3.6.1.4.1.674.10892.1 includeAllDisks 95% 1.2.3.4 is the local machines IP and everything is working locally. 5.6.7.8 is the remote machine and initially I am just trying to touch SNMPD with snmpwalk from the remote machine; snmpwalk -v 2c -c reallysafe 1.2.3.4 Timeout: No Response from 1.2.3.4 I have added to iptables as the very first rule; -A INPUT -p udp -m udp --dport 161 -j ACCEPT With such a loose iptables rule I can't see why I can't even touch the SNMPD on that Uubuntu Machine. There are more specific rules further down the table but as I couldn't connect I added the above. TCPDump shows the UDP packets coming in. What could be going wrong here?

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• Looking for Remote Control that works with everything (even Windows 7 Media Center)

  - by T Reddy

  Using my Google-Fu, it seems that the most basic of things one gets with any DVR is the remote control. Had I known it would be difficult just to get a consumer IR receiver for Windows 7 I may not have bothered to build an HTPC. But too late, I already have the HTPC ready to go (minus the CETON card...) So I'm moving away from TiVo, I hate paying the monthly fees and my box is ancient. I'm looking for these solutions to my HTCP setup...I want to: Switch audio from HDMI to SPDIF via the remote control (i.e., switch from TV to Receiver) (as a side note, the built-in audio on the mobo has software to do this). Pressing the volume button on the remote will always change the TV's volume (or the Receiver's if possible) and NOT the PC's volume. The remote/receiver works well around 25 feet. Bonus if the IR Receiver can work with my existing TiVo remote (or other remotes laying around the house) I read a review of the Bluetooth TiVo remote...it sounds promising...but I'm not sure if it is great for Windows 7 HTPC?

  Read the article

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• Wireless very slow on one laptop on network, all other machines normal?

  - by th3dude19

  My new laptop (Acer Aspire Timeine 3810TZ running Windows 7 Home Premium 64bit) is acting very strange on my wireless network. Below are the issues I'm noticing... The connection frequently drops. I see the icon change from 'full bars' to 'empty bars with yellow star (meaning no connection)' occasionally. Almost every website I visit (Firefox) hangs for a long time on 'Looking up www.amazon.com' for example. After a long pause, it finally starts loading the website. Neither of these problems exist on any other machines on my network. I also have a desktop running the same OS wirelessly and it works fine. I've run several Speedtest.net tests and the speeds are great (20MBit down/4 up). Results from pingtest.net are as follows: Line quality: D Ping: 46ms Jitter: 65ms Packet Loss: 9% These results are to a server that is less than 10 miles from my residence. The results on the other machines in my house are normal. Any suggestions? This is becoming very annoying as I purchased this machine primarily for browsing.

  Read the article

• Prevent SSL certificate being returned for a specific domain

  - by jezmck

  Apologies for a long question: We've taken on a new client whose web hosting was previously on their in-house server which still has their Exchange/Outlook email. We now host their domain (and many others) on our server. They're complaining that they're getting errors in Outlook. I don't understand the AutoDiscover stuff at the root of the problem, but believe that I just need to stop the SSL certificate on our server being returned when requested at a particular domain: Yes it is, the issue lies with "{newclient}.com" being pointed to your server IP and that server has Port 443 open with an SSL certificate associated to it. So when Outlook/ActiveSync use autodiscover to find the mailbox settings it find your SSL (because 443 is open) and flags it as an error. The solution is to close 443 so its not discovered, Autodiscover will then proceed to mail.{newclient}.com via the MX / ServiceRecords and discover the correct SSL. I'm new here and there was no hand-over, so I don't know whether other currently hosted sites need to accept SSL connections, though I suspect some will, or may in future. This is a live server, so I can't risk trying loads of options in case I take the server offline! I feel like I should be adding something like the following to vhosts.conf. <VirtualHost *:443> ServerName {newclient}.com ServerAlias www.{newclient}.com SSLEngine Off SSLCertificateFile {NONE} SSLCertificateKeyFile {NONE} </VirtualHost> Apologies for the fact that I don't know enough about this subject to be able to ask the question more clearly!

  Read the article

• How to use a home network patch panel?

  - by Torben Gundtofte-Bruun

  I'm planning a home network in a house that's not built yet. One recommendation is to add network sockets in various rooms and have them all end in a central place, where it all connects using a network switch. So far so good. Another recommendation says to not connect everything directly to the switch, but to a patch panel which in turn is connected to the switch. I'm unsure why this is good. Is there any practical advantage of using a patch panel if you're not planning to re-wire things very often? How does a patch panel actually work? Let's say it has 24 ports. Does it have another 24 ports on the backside that go to the switch, or what? Wikipedia isn't helpful on this. Clarification: I am planning to run network cables through conduits inside the walls and terminated with network sockets in the wall (as opposed to having just conduits and long regular network cables that have a normal plug in each end). Going by RedGrittyBrick's answer, a patch panel is nearly unavoidable in that case.

  Read the article

• Difference between CurrentClockSpeed and MaxClockSpeed

  - by Ben

  Rationale this belongs on ServerFault rather than StackOverflow - I already have my program which gets the value, I am querying the value returned and what it means. I have an in-house program which audits our company PCs, and one of the things it checks is the speed of the processor. To do this, it queries the Win32_Processor WMI class and gets the value of CurrentClockSpeed. We were playing with the data today and found an anomaly with some of the speeds being reported incorrectly (for example, CurrentClockSpeed said 1.0GHz, whereas the CPU name said Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz [Confirmed it is in fact 1.83GHz]). I did a bit of digging on the internet and found this blog post which might explain what is going on. My initial thought was that I could change the program to instead get the value for MaxClockSpeed instead of CurrentClockSpeed, but Microsoft's documentation doesn't clearly define what this will return. What I mean by that is will this return a value which is its actual maximum speed (say if it were overclocked) but which it would not normally be running at, or would it return what I expect, which is its maximum speed under normal (not overclocked) conditions?

  Read the article

• Transferring an SQL Processor License to a virtual hosted environment

  - by Andrew Shepherd

  My company is currently hosting a service in-house, and we want to move to an externally hosted environment. We would then be using a virtual server. I understand that this might be spread across multiple machines, but from my perspective as a customer, this layer is abstracted away - I shouldn't know or care about the hardware that the OS is hosted on. We have a licensed edition of SQL Server 2008. This is one Processor license. Will it be a violation of the licensing agreement to use this in a virtual environment. From the reference guide here it says When licensed Per Processor With Workgroup, Web, and Standard editions, for each server to which you have assigned the required number of per processor licenses, you may run, at any one time, any number of instances of the server software in physical and virtual operating system environments on the licensed server. However, the total number of physical and virtual processors used by those operating system environments cannot exceed the number of software licenses assigned to that server For enterprise edition there is an added option: if all physical processors in a machine have been licensed, then you may run unlimited instances of SQL server 2008 in one physical and an unlimited number of virtual operating environments on that same machine. I'm having trouble getting my head around this. Would I theoretically have to get a license for every processor in this virtual environment (which is effectively impossible because I have no way of knowing how many processors there actually are)? Or can I just say that it's hosted on one "virtual" server, so that's OK?

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• How can I connect my Xbox to my Mac on my network

  - by codecowboy

  I have a wireless router/modem (Router 1) in my living room. This is connected to the internet (cable). Wireless is disabled as the router has a terrible wireless range. My Xbox is connected via ethernet to Router 1. Another LAN output from Router 1 connects to a powerline adapter. Router 1 acts as a DHCP server on 192.168.0.x and has the IP 192.168.0.1 In a second room I have Router 2. This has the powerline feed from Router 1 going into the WAN socket. This router runs the Tomato Firmware and acts as a wireless router for the rest of the house using the IP range 192.168.1.x. Router 2 IP is 192.168.1.1. My Mac is connected to Router 2 using a LAN cable and has the IP 192.168.0.133. Several mobile devices need wireless access. I want an ethernet connection to my Mac, not wireless. I should be able to use software like Connect360 to share media from my Mac to the XBox but the XBox does not see my Mac. I can ping 192.168.0.1 from the Mac. Is this possible using my current setup? If so, how?

  Read the article

• Cepstral Analysis for pitch detection

  - by Ohmu

  Hi! I'm looking to extract pitches from a sound signal. Someone on IRC just explain to me how taking a double FFT achieves this. Specifically: take FFT take log of square of absolute value (can be done with lookup table) take another FFT take absolute value I am attempting this using vDSP I can't understand how I didn't come across this technique earlier. I did a lot of hunting and asking questions; several weeks worth. More to the point, I can't understand why I didn't think of it. I am attempting to achieve this with vDSP library. it looks as though it has functions to handle all of these tasks. However, I'm wondering about the accuracy of the final result. I have previously used a technique which scours the frequency bins of a single FFT for local maxima. when it encounters one, it uses a cunning technique (the change in phase since the last FFT) to more accurately place the actual peak within the bin. I am worried that this precision will be lost with this technique I'm presenting here. I guess the technique could be used after the second FFT to get the fundamental accurately. But it kind of looks like the information is lost in step 2. as this is a potentially tricky process, could someone with some experience just look over what I'm doing and check it for sanity? also, I've heard there is an alternative technique involving fitting a quadratic over neighbouring bins. Is this of comparable accuracy? if so, I would favour it, as it doesn't involve remembering bin phases. so questions: does this approach makes sense? Can it be improved? I'm a bit worried about And the log square component; there seems to be a vDSP function to do exactly that: vDSP_vdbcon however, there is no indication it precalculates a log-table -- I assume it doesn't, as the FFT function requires an explicit pre-calculation function to be called and passed into it. and this function doesn't. Is there some danger of harmonics being picked up? is there any cunning way of making vDSP pull out the maxima, biggest first? Can anyone point me towards some research or literature on this technique? the main question: is it accurate enough? Can the accuracy be improved? I have just been told by an expert that the accuracy IS INDEED not sufficient. Is this the end of the line? Pi PS I get SO annoyed (npi) when I want to create tags, but cannot. :| I have suggested to the maintainers that SO keep track of attempted tags, but I'm sure I was ignored. we need tags for vDSP, accelerate framework, cepstral analysis

  Read the article

• How do I Forward root's email to an external email address?

  - by ErebusBat

  I have a small server (Ubuntu 10.04) at my house and I would like to forward root's email to my gmail hosted domain to get security notifications and what not. I ripped everything out and started from scratch and ran into some other issues. I now have sendmail working in the sense that I can mail [email protected] and get the mail. HOWEVER, adding an address to /root/.forward does not actually forward the message. I get the following in my logs: Dec 22 14:04:37 batcave sendmail[4695]: oBML4bAT004695: to=<root@batcave>, ctladdr=aburns (1000/1000), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30075, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (oBML4bJ9004696 Message accepted for delivery) Dec 22 14:04:39 batcave sm-mta[4698]: STARTTLS=client, relay=[69.145.248.18], version=TLSv1/SSLv3, verify=FAIL, cipher=DES-CBC3-SHA, bits=168/168 Dec 22 14:04:40 batcave sm-mta[4698]: oBML4bJ9004696: to=<[email protected]>, ctladdr=<[email protected]> (1000/1000), delay=00:00:03, xdelay=00:00:03, mailer=relay, pri=120336, relay=[69.145.248.18] [69.145.248.18], dsn=2.0.0, stat=Sent (OK 01/D4-00853-216621D4) You can see where my local sendmail instance accepts it then hands it off to my ISP, but with the wrong address ([email protected]).

  Read the article

• 802.11g -> wired ethernet bridging not working

  - by Malachi

  Usually people want to go the other direction, but I want to take our relatively fast and stable house 802.11g signal and bridge it to ethernet. I have tried using an Airport Express (the b/g flavor) and my i7 MacBook pro, both to no avail. Word is that the b/g flavor of This flavor of Airport Express maxes at firmware 6.3 which doesn't support this kind of bridging properly. However, I expected my MacBook pro to do the job with its "Internet Sharing" feature. Alas, although my wired PC does sort of see it, it doesn't work out. Strangely, using DHCP the PC receives the same IP address as my MBP uses on the network. Less strangely, but still surprisingly, the wired ethernet port on my mac registers as the IP address of the gateway when queried with IFCONFIG. It sort of makes sense that the mac would "pretend" to be the gateway, but the whole thing just isn't working and seems configured wrong - but all the docs I see say basically "OS X Internet Sharing: click it and go". What do I do? Do i really have to buy more hardware, even though I have plenty of would-be candidates for bridging? Incidentally, the host router originating the 802.11g signal is a belkin 802.11g router, and is documented to support WDS.

  Read the article

• Wireless router setup for 1-1 NAT

  - by Carlos

  What I have: A linksys router WAG160N with firmware version 2 A "pool" of 5 external static IP's provided by my ISP 213.xx.xxx.n All the required configuration values for the static IPs such as (Subnet Mask, Gateway and static DNS 1, 2, 3) Current WAN Configuration: Encapsulation: RFC 2364 PPPoA Multiplexing: VC QoS type: UBR DSL modulation: MultiMode What's connected to the network: 1 x Server (That I want to make available to the outside) 5 x Desktops with static internal IP's, such as 192.168.0.xx 2 x Network printers, also with internal static IP's 2 x Laptops 1 x NAS (Network Attached Storage) also on static IP What I want to do: I would like to make the server available from outside the network, for example from your house. The problem is that Im not really sure how to do this. I have tried following the steps on the instruction manual in Linksys but they do not seem to work, once I set it up as shown bellow, I loose internet and all hell breaks loose. Going into further detail, I would prefer if the network is changed as little as possible, by this I mean that all the computers stay networked within eachother and only the server is accessible from the outside the network. What I need HELP with: I have read around that it is possible to set a 1-1 NAT (I know where it is in the menu but have no clue what it does...) so that I can NAT a single public IP directly to a single private IP (in our case the server). But please, How do I do that? Or maybe an alternative?

  Read the article

• using gmail as email relay for sendmail

  - by Nikita

  I used to be able to send emails using a gmail account & sendmail configured using one of the guides on the Internet, for example: http://appgirl.net/blog/configuring-sendmail-to-relay-through-gmail-smtp/ This is a small server and I've recently moved it to a different house. And sendmail has stop working. The only thing different in the network setup is a new router. What is happening: In the log files, I see the following error: ...stat=Deferred: smtp.gmail.com: No route to host When I run from the command line: strace sendmail -f A -t B -u "Subject" -m "Message" -tls=yes ssl=yes -s smtp.gmail.com:587 -xu A -xp XYZ It hangs on this call: recvfrom(3, "m0\201\203\0\1\0\0\0\0\0\0\4ares\3lan\0\0\34\0\1", 8192, 0, {sa_family=AF_INET, sin_port=htons(53), sin_addr=inet_addr("192.168.1.254")}, [16]) = 26 close(3) = 0 time(NULL) = 1339997943 open("/etc/localtime", O_RDONLY) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb76ff000 read(3, "TZif2\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\4\0\0\0\4\0\0\0\0"..., 4096) = 3477 _llseek(3, -24, [3453], SEEK_CUR) = 0 read(3, "\nEST5EDT,M3.2.0,M11.1.0\n", 4096) = 24 close(3) = 0 munmap(0xb76ff000, 4096) = 0 socket(PF_FILE, SOCK_DGRAM|SOCK_CLOEXEC, 0) = 3 connect(3, {sa_family=AF_FILE, path="/dev/log"}, 110) = 0 send(3, "<18>Jun 18 01:39:03 sendmail[268"..., 96, MSG_NOSIGNAL) = 96 nanosleep({60, 0}, So it looks like at some point it tries to resolve the DNS name, but I don't have anything running on 53, so it dies out and then just hangs. The other interesting thing is that msmtp works just fine on the same server. Update: ares in strace output is actually the name of my server, but .254 IP address is the address of the router. Could anyone tell me why this is happening or what further steps can I take to investigate the issue? Thanks!

  Read the article

• How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment [closed]

  - by lmttag

  Possible Duplicate: How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment We have an ASP.NET Web API server that serves up a SQL Server data driven website. The API uses JSON to transfer data from SQL Server to the front end. We need to move it to an internal production environment (nothing will be exposed on the public Internet) and we’re having problems - or just not understanding what needs to be done. There are two domains: The corporate domain - where all users login normally. The process domain - contains the database the Web API needs to access. The IT staff wants to put a DMZ between the two domains to house the IIS app and shield the users on the corporate domain from having access into the process domain directly. The ideal configuration is: corp domain (end users) <–> firewall (open port 80) <–> DMZ (web server running IIS) <–> firewall (open port 80 or 1433????) <–> process domain (IIS for Web API and SQL Server) We don’t really understand how to deploy our browser/Web API application in this scenario. Do we need to break up our application so that all the client code is on the IIS server in the DMZ, while the Web API gets installed on the server in the process domain? Does the entire app (client code and Web API) stay together on the IIS server in the DMZ, which then somehow accesses the SQL Server instance to get data? From the IIS server and app in the DMZ, would you simply access the Web API on the server in the process domain by going to http://server/appname/api/getitmes? In the second firewall between the DMZ and the process domain, would you have to open port 1433 or just port 80 since the Web API is a HTTP endpoint? Or, is there some better way of deployment (i.e., how ASP.NET Web API single page applications written all in HTML5 and JavaScript supposed to be deployed to production environments?)? NB: The servers are Win2k8 R2, SQL Server 2k8 R2, and IIS 7.5.

  Read the article

• Which project management software for technophobes who've never worked with something like that?

  - by Ernst

  Hi, Our director has asked me to get something to manage projects. Note that so far we haven't used anything of the sort. I did not get very clear instructions yet, probably because she doesn't know exactly what we need either. My guess is, we'll only find out while using something. I've looked at some, openworkbench, ganttproject, and microsoft project. The latter has the advantage of easy importing of users from exchange, are there others that do that (even if not directly, easily)? I don't think it's a critical requirement though. We're using some other custom software where I have to add users manually anyway and we're small enough that it's maybe once a month that I have to add or remove a user. In any case, I'm not in favour of buying anything, since I'm skeptic about us actually succeeding in putting it to good use, and even if we do, we will only during usage discover what we need. We're also not a tech shop, most people vary from not very technically adept to technophobic. This means we need something very userfriendly. I prefer to stay away from online solutions, since we deal with sensitive information and I prefer to keep that in house, but I guess it would be acceptable for the trial period. An intranet site is an option though, but preferably something that is easy to set up with IIS. Xplanner plus and redmine I found too hard to set up for this experiment. Some other options I haven't yet tried to install, but which look to complex for our technophobes: Endeavour Software Project Management, Project-Open, Trac. Any suggestions? Thanks, Ernst

  Read the article

• How should a small company administer their web server?

  - by John Isaacks

  We currently have our website hosted by a small company that is actually a reseller for Rackspace. They act as our server administrators. They configured the servers, handle the backups, if there is a problem, we call them and they fix it. We are growing and want to move away from our shared server to either a cloud or dedicated server. I am thinking cloud myself but I am open to either. The current company doesn't seem to want to offer us anything more than a shared hosting plan. I looked into cloud solutions at vps.net, with them I would have to be the server administrator myself. I am the website programmer but administering the server is outside my comfort zone. vps.net does have a $99/month plan for Pro-Active Managed Support but I am not sure if this is the equivalent on a server admin that is there when you need them. We could hire someone in house, but I think that would be overkill for our needs. I am not exactly sure what we need, I do know we need as close to 100% uptime as we possible can. and we need the ability to add/remove/change the server configuration/software/etc. when needed (though changes shouldn't be very often once everything is setup right). Can someone point me in the right direction? What do other companies do?

  Read the article

• sharepoint crawl not indexing main site

  - by user22215

  Guys I'm having some strange search issues' going on with my main portal application. First off let me give you a little back ground on the problem web app. Our Sharepoint environment was originally set up by a consultant that did not follow best practices. She used one web app to house our companies' intranet site, ssp, and mysites. Since than I have provisioned a new ssp that I have segmented correctly I moved all of our other sites over to the new ssp with out any problems . However, I could not assign the main portal app to the new ssp since the portal app housed the ssp site collection. So I deleted the ssp site collection after that I deleted the ssp and assigned the portal app to my new ssp. Now this is where the problem starts when I attempt to crawl this application the crawl starts than stops 5 seconds later with a status of success also it reports that 1 item was successfully crawled. The funny thing is the main portal app has nearly 30000 items. I have tracked the problem down to the web app if I create a test web app than restore the content I have no problem crawling all 30000 items. Also all of my other web apps that use the same ssp have no problem completing crawls. I don't see anything in the ULS logs or server 2003's event viewer. Also I'm using a separate dedicated index server that's configured to crawl itself via host file configuration. I would like to fix this problem with out having to recreate our main portal site due to the fact that we have several custom code modifications where DLL's were registered to the IIS bin folder also I don't even want to get into the Silverlight mods that were done. Any help with this problem is much appreciated Same problem as minehttp://www.experts-exchange.com/OS/Microsoft_Operating_Systems/Server/MS-SharePoint/Q_23885820.html

  Read the article

• Can a Windows Domain play along with a Hosted Exchange service?

  - by benzado

  I'm setting up a computer network for a small (10-20 people) company. They are currently using a Hosted Exchange service they are totally happy with. Other than that, they are starting from scratch (office doesn't even have furniture yet). They will need some kind of file sharing server set up in their office. If I set up a machine as a file server and nothing more, users will have three passwords to deal with: local machine, file server, and email. If I set up a Domain Controller, identities for local machine and file server will be the same. But what about the Hosted Exchange server? Must the users have a separate email password, or is it possible to combine the two? (I realize it might depend on the specific hosting provider, but is it possible?) If not, it seems like I have these options: Deal with it: users have a separate email password. Host Exchange on the local server: more than they want to manage in-house? Purchase a hosted VPS, make it part of the domain, and host Exchange there. (Or can/should a VPS be a domain controller?) I realize I have a lot of questions in there. The main one: is there any reason to use a Hosted Exchange service if I'm setting up other Windows services?

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >