Search Results

Search found 39386 results on 1576 pages for 'public ip'.

Page 53/1576 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

  • Why does ping flooding a domain name freezes and not a direct ip address

    - by CYREX
    I am wondering why, when ping flooding a domain, the ping flood freezes after a couple of seconds then continues and this freeze, unfreeze continues until i stop the ping flood. When i do the same using the ip it does not freeze. NEVER. i did for example sudo ping -f IP (It does not freeze) then i did sudo ping -f DomainName (It freezes after a couple of seconds) Why does ping flooding an IP not freezes and ping flooding the same place using the domain name does freeze. EDIT - What i mean about freezing is that the behavior of the ping flood should send a ping and create a dot (.) for each ping but also remove each dot (.) after receiving the echo request. Looks something like this: .......... <-- This means you just send 10 ping requests. If the requests are answer, for each request answer a dot is removed. The freeze happens when this is sending or receiving. The dots will stay there frozen, like is not receiving or sending any packets. For the PING FLOOD. I do not mean in the evil way of flooding a place, i mean in the testing way. To test the performance/speed of the request send and answered of the ping requests. If you send a ping flood to google's IP for about 10 seconds you would have send about 1000 packets.but if you do it to google's domain name (google.com) it will create the freeze am talking about. IMPORTANT - Do not confuse with flooding a site with ping of death attacks.

    Read the article

  • Two domains, two servers, one dynamic IP address

    - by giantman
    I have two domains hi.org and bye.net and one dynamic IP address and two servers. I want to attach one domain bye.net to server1 and hi.org to server2. I'm using Apache wamp 2.0i. I have two servers behind one router with a dynamic IP address #httpd.conf file additions <IfModule mod_proxy.c> ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> </IfModule> #vhost file additions NameVirtualHost *:80 #default <VirtualHost *:80> DocumentRoot "c:/wamp/www/fallback" </VirtualHost> # Server 1 <VirtualHost *:80> DocumentRoot "c:/wamp/www" ServerName h**p://bye.net ServerAlias bye.net </VirtualHost> # Server 2 <VirtualHost *:80> ProxyPreserveHost On ProxyPass / h**p://192.168.1.119/ DocumentRoot "g:/wamp/www" ServerName h**p://hi.org ServerAlias hi.org </VirtualHost> After doing all this I fallback to server1 only I don't get the page hi.org I only get the page bye.net, I don't even get the default fallback page which gets executed when a person enters IP address but not the domain name. I use Windows 7 (server 2) and Windows XP (server 1) UPDATE: I needed to remove DocumentRoot "g:/wamp/www" line :D it was there by mistake! things are working fine now. But one thing: the URL gets replaced by the local ip address any way to not make that happen?

    Read the article

  • D-LINK 2450U DSL router: Port forwarding forwading to the modem itself, not the specified IP

    - by axk
    I found a similar question but it has no satisfactory answers. I have a D-LINK 2540U DSL router. It has a basic port forwarding(under DNS - Virtual Servers) configuration in the administration panel where you specify: external port range, protocol, internal port range, server IP address and it is supposed to forward that port to that IP address. When I first set it up for a Real VNC connection it worked fine, just as I expected. Then I added a DynDNS configuration entry in the router's 'Dynamic DNS' section and added an additional SSH (22) forwarding rule. The SSH forwarding also worked fine (now with the dynamic hostname, but I suppose it doesn't make any difference as far as SSH is concerned). Then I removed the SSH rule and after that the VNC forwarding stopped working with the VNC client failing to connect (I have tried to connect with telnet and it also failed to connect, so it wasn't a VNC problem). After adding a rule for port 80 it turned out it would forward on port 80 though not to the specified server IP but to the modem itself. At least it is what it looks like, because it gives me the administration panel when I connect to my external IP (both using a browser and plain telnet in which case I can see that it is mini_hhtpd sitting on the port, which is obviously the modem's administration panel). Have anybody encountered a similar problem with port forwarding? I have tried to do a reset through the administration panel and to restore a backup of the settings made before I started playing with port forwarding, but it didn't help. Should I do a 'hard' reset with the button on the modem? Is it any different from the administration panel's reset (Restore default)?

    Read the article

  • Using virtual IP with stunnel and haproxy

    - by beardtwizzle
    Hi there, We have a load-balancer setup, in which an HTTPS Request flows through the following steps:- Client -> DNS -> stunnel on Load-Balancer -> HAProxy on LB -> Web-Server This setup works perfectly when stunnel is listening to the local IP of the Load-Balancer. However in our setup we have 2 load-balancers and we want to be able to listen to a virtual IP, which only ever exists on one LB at a time (keepalived flips the IP to the second LB if the first one falls over). HAProxy has no problem in doing this (and I can ping the assigned virtual IP on the load-balancer I'm testing), but it seems stunnel hates the concept. Has anyone achieved this before (below is my stunnel config - as you can see I'm actually listening for ALL traffic on 443):- cert= /etc/ssl/certs/mycert.crt key = /etc/ssl/certs/mykey.key ;setuid = nobody ;setgid = nogroup pid = /etc/stunnel/stunnel.pid debug = 3 output = /etc/stunnel/stunnel.log socket=l:TCP_NODELAY=1 socket=r:TCP_NODELAY=1 [https] accept=443 connect=127.0.0.1:8443 TIMEOUTclose=0 xforwardedfor=yes Sorry for the long-winded question!

    Read the article

  • LAN->LAN IP translation (for TortoiseSVN + Artifacts + Buffalo router)

    - by Armchair Bronco
    Here's my scenario: I've got a VisualSVN server on my main dev box @ home. I'm also using Visual Studio 2010, TortoiseSVN, VisualSVN client (for source control), and Versioned 'Artifacts' (for bug tracking). (I had to modify the fake URL's below to use only one slash because as a new user, I can't post more than one real URL.) I've got my Buffalo AirStation WHR-HP-G300N router properly configured so my business partner can connect to the SVN server. I have port forwarding enabled for the internet-side IP address (like http:/99.888.77.66:443) which gets forwarded to an internal IP (like 192.168.11.6). This part is working great. The problem I'm having is with the integration piece between TortoiseSVN and my bug tracking system. I need to provide a bugtraq:url property, but I haven't been able to get relative paths to work. So I'm forced to use an absolute URL. On my end, I need to use the name of my server (for example: bugtraq:url = https:/my-server/svn/bla..), but this doesn't work for my partner. He needs to specify the IP address (for example: bugtraq:url = https:/999.888.77.66:443/svn/bla...) Is there a way to configure my router such that the IP address for this parameter gets re-routed/re-mapped to "https://my-server" if the request originates from the LAN itself? My router's software supports LAN-Internet and Internet-LAN, but I don't see LAN-LAN.

    Read the article

  • Changing IP address in IIS for SharePoint site results in Directory listing error

    - by Dan
    I have a server here that has 2 roles. One is Exchange 2007 and the other is MOSS 2007. In IIS i have a site, go.domain.com which has our OWA. The other is internal.domain.com which is the MOSS site. I have given the NIC local IPs and each site is using host headers. The GO site has an SSL cert from NetSol, and the MOSS site has a self signed. Right now going to either shows the NetSol site, which browsers complain about when going to the internal.domain.com site, obviously, since they are on the same IP in IIS. Both sites have always run off the original IP of 10.0.0.3 in IIS. When i added the second IP to the NIC, (10.0.0.6) and changed the Sharepoint site in IIS to use this for http and https access, I now get this message in a browser when trying to connect. Directory Listing Denied This Virtual Directory does not allow contents to be listed. Changing the IP back to 10.0.0.3 and the internal site is back up. What am I missing here? Do i need to fool around with Alternate Access Mappings in Central Admin? Am i completely missing the point with multiple SSL certs and host headers?

    Read the article

  • OSX: Mimic Ubuntu IP Masquerading via iptables with ipfw

    - by Dogbert
    Good day, I am attempting to replicate a setup I have between a router and an Ubuntu PC, and have the same setup working on my MacBook (10.6, Snow Leopard). First, I have a router that has a USB port. When I plug it into my Ubuntu PC, it creates an RNDIS connection, allowing me to connect to the router over the USB cable via an IP connection. When I plug it into my computer via USB, it gets assigned an IP address of 172.16.84.1, and a new adapter appears when I type ifconfig. I can then SSH into the device via ssh [email protected]. When I log in to the device, I flush the routes, then create the default route: admin@localhost> route -f admin@localhost> route add default 172.16.84.2 Now, in my Ubuntu machine, I use iptables to enable IP masquerading: root@Valhalla> sudo iptables -t nat -A POSTROUTING -s 172.16.84.2 -j MASQUERADE Once this is all done, the router has internet access over the USB connection to my PC. I am trying to replicate this exact setup on my MacBook now (Snow Leopard), but iptables does not exist for OSX, not even a Macports version exists. I have scoured through other questions on StackOverflow that cover the usage of the ipfw command, which apparently works as a drop-in replacement for iptables. However, the syntax is significantly different, and I'm pretty much lost. Does anyone with some experience with ipfw have some suggestions on how I could accomplish this and create a NAT connection via IP masquerading like I could with my Ubuntu PC? Thank you for your assistance.

    Read the article

  • Mac OS X Client With Static DHCP Assignment Requests Wrong IP via Option 50

    - by Starchy
    I have a number of Mac (and a few Linux) laptops getting DHCP from a Force10 layer 3 switch, the only DHCP server on the subnet. There's a global dynamic pool, and for each full-time employee's laptop I have a single IP static pool set by MAC address. One and only one of the clients, running OS X 10.7.5, consistently fails to get a static assignment. The MAC address in the static pool definition has been carefully re-checked. Running tcpdump on a mirrored port when the laptop connects, I see that it is specifically requesting 10.100.0.252 (a dynamic address): 11:32:10.108280 IP (tos 0x0, ttl 255, id 28293, offset 0, flags [none], proto UDP (17), length 328) 0.0.0.0.bootpc > broadcasthost.bootps: [udp sum ok] BOOTP/DHCP, Request from 3c:07:54:xx:xx:xx (oui Unknown), length 300, xid 0x1399da89, Flags [none] (0x0000) Client-Ethernet-Address 3c:07:54:xx:xx:xx (oui Unknown) Vendor-rfc1048 Extensions Magic Cookie 0x63825363 DHCP-Message Option 53, length 1: Request Parameter-Request Option 55, length 9: Subnet-Mask, Default-Gateway, Domain-Name-Server, Domain-Name Option 119, LDAP, Option 252, Netbios-Name-Server Netbios-Node MSZ Option 57, length 2: 1500 Client-ID Option 61, length 7: ether 3c:07:54:xx:xx:xx Requested-IP Option 50, length 4: 10.100.0.252 Lease-Time Option 51, length 4: 7776000 Hostname Option 12, length 10: "host-name" END Option 255, length 0 PAD Option 0, length 0, occurs 8 I haven't been able to find any extra system prefs or unusual software on the laptop. Disabling the interface and rebooting or temporarily setting the IP manually both fail to make any difference. Any suggestions appreciated.

    Read the article

  • Windows 2008 R2 forgets static IP configuration after reboot

    - by Andrew
    I've got an issue where a Windows 2008 R2 Standard (SP1) server loses its static IP configuration upon a reboot. It's a sysprep'd image. The following steps reproduces the problem: Using the SAC, set the IP using 'i' Use the Win32 EnableStatic() method to set an IP (and then SetGateways()) through PowerShell Reboot The machine boots up with the following configuration: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : [...] Autoconfiguration IPv4 Address. . : 169.254.152.31 (incorrect) Subnet Mask . . . . . . . . . . . : 255.255.0.0 (incorrect, was set to /24) Default Gateway . . . . . . . . . : 1.1.1.1 (correct) Occasionally, the gateway is also incorrect (0.0.0.0) The images have a script that runs 'netsh int ip reset' after sysprep finishes (before the reboot), so it appears that does not solve the issue. (the problem also happens without this step) After the reboot, using 'i' on the SAC resolves the issue permanently. (But I'd like to know the root cause as having to run 'i' again isn't ideal)

    Read the article

  • subdomains to different VMs on one IP address

    - by efbenson
    I have a setup at home with an ESXi server Freenas server and several win7 clients. I have a domain refactoringme.com I set the @ and WWW domain record to my (current) IP address. I then forwarded port 80 to my local win2k3 server on my Linksys router and used host name matching to run the 5 test sites I have. That all works. Now I want to use the turnkey machines and move to dedicated VM servers. One for a wiki one for SVN etc. So how do I get www.refactoringme.com to go to one internal IP address and wiki.refactoringme.com to different internal IP address, while they both use the same external IP address? I added the additional record for wiki to my domain and pointed it to @. I figured it had to be involving a real firewall. So I installed PFSense on a VM and set it on the DMZ on my Linksys. From this point I haven't had any luck. I thought that maybe it would be in the DNS Forwarder or maybe in the Rules sections but neither have worked. Am I doing it wrong or on the right track but am missing something. Thanks for all the help.

    Read the article

  • Multi-IP address zimbra server DNS PTR records and spam

    - by David Fraser
    We have a mail server running Zimbra (ZCS 6.0.8). The server has 5 active public IP addresses in the same subnet. (.226-.230). I currently have A records for each of these (host0.domain.com..host4.domain.com), with the main host.domain.com of the machine pointing to .226. Our host has ended up being listed on the SORBS DUHL list (even though it's in a server farm). According to them you can get removed quickly by checking that your host has an MX record, an A record, and a PTR record that points back to the hostname given in the MX record. I tried setting the PTR records so that each of these addresses resolved back to their A record (i.e. .228 had a PTR to host2.domain.com). However, I then got mail being rejected from other servers because when Postfix (under Zimbra control) sends out mail, it uses the main hostname for the HELO - there doesn't seem to be any way to override it. So the PTR records currently say host.domain.com for all 5 IP addresses. What's the correct way to handle this? Should I have an A record for the domain that points to all the IP addresses (for round-robin handling)? I'm nervous of changes that could cause problems, so I'm wondering what the standard way to handle a multiple-IP-address mail server is.

    Read the article

  • Valid IP address but can't surf without rebooting

    - by Kat
    I periodically lose internet and router connection at home. When this happens, others are using the router just fine. I am connecting directly through a wired connection to a Belkin router. I can release and renew the IP (and the IP addresses change to 0.0.0.0 and to an IP in my router's range beginning with 192.168.2. as they should) but still can't surf, can't access the router interface. Cycling the router doesn't help, and again, others are able to access the router fine at this time. Only rebooting the computer resolves the issue, and everything is wonderful for a few hours- and then I lose connection again. I have several ideas where to go from here, but I'd like to get some advice first. (Using Windows XP SP3, hardwired connection) Update As stated in the originally, releasing and renewing doesn't solve the issue. However, I have an update. I can ping localhost and my router IP with no problem at all when the issue occurs. However, repairing the network connection does not help. I AM able to get back on by disabling and then re-enabling the network connection in XP. What does that tell us?

    Read the article

  • Need for explanation: NetBIOS over TCP/IP on VMware network adapter disturbs access to network share

    - by gyrolf
    (Moved here from StackOverflow) Some time ago nearly all workstations in our team (Windows XP SP2) exhibited intermittend but frequent delays when accessing shares on the network. Typically the first access to a share which hadn't been accessed for some time resulted in a nearly frozen workstation for up to 30 seconds. Then everything started working fine again. Using TCPView from Sysinternals I saw that during this delays there was a connection to the netbios-ssn port on the file server which was in state SYN_SENT. First try: Disable NetBIOS over TCP/IP for the intranet network adapter. Problem solved, but I didn't like to manipulate our centrally managed network configuration for the intranet. Second try: Disable NetBIOS over TCP/IP only for the VMWare network adapter (VMNet1 used for host only communications). Problem solved again! My questions: Why does NetBIOS over TCP/IP on one network adapter disturb NetBIOS over TCP/IP on another network adapter? Is this problem specific to VMWare network adapters? Has anybody else seen this phenomen? Additional information: VMWare Workstation version 6.0.3 At the time I started seriously analysing the problem it was no more possible to find out what had been changed to our systems at the time the problems started.

    Read the article

  • IP-dependent local port-forwarding on Linux

    - by chronos
    I have configured my server's sshd to listen on a non-standard port 42. However, at work I am behind a firewall/proxy, which only allow outgoing connections to ports 21, 22, 80 and 443. Consequently, I cannot ssh to my server from work, which is bad. I do not want to return sshd to port 22. The idea is this: on my server, locally forward port 22 to port 42 if source IP is matching the external IP of my work's network. For clarity, let us assume that my server's IP is 169.1.1.1 (on eth1), and my work external IP is 169.250.250.250. For all IPs different from 169.250.250.250, my server should respond with an expected 'connection refused', as it does for a non-listening port. I'm very new to iptables. I have briefly looked through the long iptables manual and these related / relevant questions: http://serverfault.com/questions/57872/iptables-question-forwarding-port-x-to-an-ssh-port-of-different-machine-on-the-n http://serverfault.com/questions/140622/how-can-i-port-forward-with-iptables However, those questions deal with more complicated several-host scenarios, and it is not clear to me which tables and chains I should use for local port-forwarding, and if I should have 2 rules (for "question" and "answer" packets), or only 1 rule for "question" packets. So far I have only enabled forwarding via sysctl. I will start testing solutions tomorrow, and will appreciate pointers or maybe case-specific examples for implementing my simple scenario. Is the draft solution below correct? iptables -A INPUT [-m state] [-i eth1] --source 169.250.250.250 -p tcp --destination 169.1.1.1:42 --dport 22 --state NEW,ESTABLISHED,RELATED -j ACCEPT Should I use the mangle table instead of filter? And/or FORWARD chain instead of INPUT?

    Read the article

  • Multiple static WAN IP addresses to single LAN subnet

    - by Jessy Houle
    Below is my home network topology. I currently have 5 static IP addresses, 3 of which are in use by 3 routers. These routers in-turn subnet internal networks and port forward. I use my SSL VPN appliance to remote home from work or on the road. At this point I can remotely administer my Windows Server. I know the network is setup wrong, I was matching existing hardware the best I knew how. http://storage.jessyhoule.com.s3.amazonaws.com/network_topology.jpg Ok this said, here is the problem... One of my websites on my Windows Server now needs to be secure (SSL using port 443). However, I'm already port forwarding port 443 to my VPN appliance. Furthermore, if I'm going to have to reconfigure the network, I would really like to be able to use the SSL VPN to remotely administer all machines. I mentioned this to a friend of mine, who said that what I was looking for was a firewall. Explaining that a firewall would take in multiple static (WAN) IP addresses, and still allow all internal devices to be on the same network. So, basically, I could supply my SSL VPN appliance it's very own static (WAN) IP address routing, and yet have it on the same internal network (192.168.1.x) as all my other devices. The first question is... Does this sound right? Secondly, would you suggest anything different? And, finally, what is the cheapest way to do this? I am started down the road of downloading/installing untangle and smoothwall to see if they will do the job, hoping they take multiple static (WAN) IP addresses. Thank you in advance for your answers. -Jessy Houle

    Read the article

  • How to test a HTTPS URL with a given IP address

    - by GreatFire
    Let's say a website is load-balanced between several servers. I want to run a command to test whether it's working, such as curl DOMAIN.TLD. So, to isolate each IP address, I specify the IP manually. But many websites may be hosted on the server, so I still provide a host header, like this: curl IP_ADDRESS -H 'Host: DOMAIN.TLD'. In my understanding, these two commands create the exact same HTTP request. The only difference is that in the latter one I take out the DNS lookup part from cURL and do this manually (please correct me if I'm wrong). All well so far. But now I want to do the same for an HTTPS url. Again, I could test it like this curl https://DOMAIN.TLD. But I want to specify the IP manually, so I run curl https://IP_ADDRESS -H 'Host: DOMAIN.TLD'. Now I get a cURL error: curl: (51) SSL: certificate subject name 'DOMAIN.TLD' does not match target host name 'IP_ADDRESS'. I can of course get around this by telling cURL not to care about the certificate (the "-k" option) but it's not ideal. Is there a way to isolate the IP address being connected to from the host being certified by SSL?

    Read the article

  • Port forwarding with multiple IP's

    - by Jon
    I work at a company which uses a Fortigate 60 router, something I'm not really familiar with. Everything worked fine with it until a week ago when Comcast came in and replaced our modem. It seemed as though the process went smoothly - our connection came back up and our static IP remained the same. However, none of our port forwarding is working. What has me confused is the Comcast modem apparently has two IP addresses. The WAN2 interface for it in the Fortigate router is set to 10.1.10.10. However, all of our port forwarding settings are set to an external IP address of 10.1.10.50. Now this setup used to work fine, so something with the Comcast modem must have changed. How can I find out what? I tried setting a computer to a local IP of 10.1.10.15 so I could open up the web interface for the modem, but I can't even ping 10.1.10.10 when I do that. Any ideas? Thanks!

    Read the article

  • Not getting IP from ISP on Multicast Network

    - by Johan Nielsen
    Im having an odd issue with my ISP (COMX.dk) I have a managed access gateway box (Telsay) with three 8P8C ports for use with Internet and Ip-Tv (respectively on different VLANS (so does my ISP tell me)) To utilize a port you will need to register your device's mac address through an online interface. You will then get your device paired with a static ip. I am using one port actively and I have registered another device (router). The router is configured to listen for an active dhcpd on the network. When my router get a lease I get a private ip 192.168.2.2 (not the one bound to my mac) which is odd! I unconnected my router from the gateway and connected my laptop directly. Same thing happened - I was given a private address. I did a port scan on the gateway and found port 80 to be open and browsed to the ip. I was then presented with a management interface of a Belkin wireless router (HMMM!!!!) <--by the way, not my gear At this point I called the ISP to let them know of my issue/findings - Only to be replied "Well, we cant see any rogue dhcp servers" (thinking to myself, well I can) I then decided that it could be fun to try the other port of my gateway, only to experience the same. So I reconnected my router and used the remaining port to make an observer(wireshark promic etc.) I am able to see my router trying to discover a dhcp server but I can also see my ISP's IGMP and PIMv2 packages just repeating the same pattern. Hello...Hello...Hello :) So I called them again, only to get the same response, "we dont see any rogue dhcp's...we cant see the host you are talking to (mac address of the Belkin router)...you are definitively connected through wireless?!?(no im not, no such thing as a wireless wire - i thought to myself)" My questions is, What is going on? (besides from what im reporting here) What am I seeing that the don't? What can I tell them in order for them to resolve mine/their issue?

    Read the article

  • Different external ip addresses from different sites

    - by user630286
    My router is ClearOS 6(Centos 6). In my router, I have two external (internet) network connections from two ISP's. The primary connection is eth2 connected to a cable modem and the second one is ppp0 connected to a dsl modem. I have assigned eth2 as the primary connection (with a high metric value). In fact this is done through clearos's multiwan web interface. I have a test in my Nagios to monitor whether the primary connection. This connection is done based on the result of curl ifconfig.me But it seems that ifconfig.me is always giving the ip address of my secondary connection. I tested it through a browser. Yes ifconfig.me gives the secondary internet's(ppp0) ip address. But whatismyipaddress.[com|org] give my primary ip address (eth2). I checked the default route on the router through ip route list 0/0 which also shows the primary connection (eth2) as the default route. The traceroute www.google.com and traceroute ifconfig.me both seems to trace through the primary connection (eth2). As our secondary internet connection has only got a limited download, I don't want to end up having to pay a large sum at the end of the month. Has somebody got an idea why the ifconfig.me shows my secondary address? What is the best way to ensure that my router(and thus the lan) use the right internet connection.

    Read the article

  • Change source address based on destination IP

    - by hgj
    We have several "router" machines that gather a lot of external IP addresses on the same host and redirect, NAT or proxy the traffic to the internal network. They also act as routers for the machines on the internal network. This works fine, however I am unable to make the routing table, so I can change the source address, based on the destination a machine from the internal network want to access. Let's say I have a router, that has public addresses P1 (5.5.5.1/24) and P2 (5.5.5.2/24). All traffic goes through P1, but if necessary, the host is reachable on P2 too. This looks like this and works fine: > ip addr ... 1: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether aa:bb:cc:dd:ee:11 brd ff:ff:ff:ff:ff:ff inet 5.5.5.1/24 brd 5.5.5.255 scope global eth1 inet 5.5.5.2/24 brd 5.5.5.255 scope global secondary eth1:p2 ... Now I want to use P2 as the source address, if I want to access the Google DNS service for example (8.8.8.8). So I add a row in the routing table like: > ip route add 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 > ip route ... default via 5.5.5.254 dev eth1 5.5.5.0/24 dev eth1 proto kernel scope link src 5.5.5.1 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 ... But this does not work. If I ping 8.8.8.8, the host still uses P1 as the source address, and does not use P2 at all for outgoing connections. Am I doing it right? I guess not...

    Read the article

  • Strange IP address showing up with OS X ssh

    - by user50799
    I was futzing around with DTrace on Mac OS X and found the following script that prints out information about connections being established: $ cat script.d syscall::connect:entry { printf("execname: %s\n", execname); printf("pid: %d\n", pid); printf("sockfd: %d\n",arg0); socks = (struct sockaddr*)copyin(arg1, arg2); hport = (uint_t)socks->sa_data[0]; lport = (uint_t)socks->sa_data[1]; hport <<= 8; port = hport + lport; printf("Port number: %d\n", port); printf("IP address: %d.%d.%d.%d\n", socks->sa_data[2], socks->sa_data[3], socks->sa_data[4], socks->sa_data[5]); printf("======\n"); } I run it in one window: $ sudo dtrace -s ./script.d Then I ssh to another machine from another window. I get this output from my dtrace window: CPU ID FUNCTION:NAME 0 18696 connect:entry execname: ssh pid: 5446 sockfd: 3 Port number: 22 IP address: 192.168.0.207 ====== 0 18696 connect:entry execname: ssh pid: 5446 sockfd: 5 Port number: 12148 IP address: 109.112.47.108 ====== ^C The first IP address I can explain (192.168.0.207), that's the machine I'm connecting to. But what's with the 109.112.47.108 machine? It doesn't show up in tcpdump nor netstat -an Is there something with my dtrace code or my understanding of how the connect system call works?

    Read the article

  • Use external inline script as local function

    - by Aidan
    Had this closed once as a duplicate, yet the so-called duplicate DID NOT actually address my whole question. I have found this script that, when run inline, returns your IP. <script type="text/javascript" src="http://l2.io/ip.js"></script> http://l2.io/ip.js Has nothing more than a line of code that says document.write('123.123.123.123'); (But obviously with the user's IP address) I want to use this IP address as a return string for a function DEFINED EXTERNALLY, BUT STILL ON MY DOMAIN. That is, I have a "scripts.js" that contains all the scripts I wish to use, and I would like to include it in that list as a local function that calls to the 12.io function, but javascript won't allow the < tags, so I am unsure as to how to do this. I.e. function getIP() { return (THAT SCRIPT'S OUTPUT); } This is the topic this was supposedly a duplicate of, and it is very similar. Get ip address with javascript However, this DOES NOT address defining as a forwarded script it in my own script file.

    Read the article

  • ¿Oficina sin papeles?

    - by [email protected]
    Recientemente hemos organizado un evento de Digitalización para mostrar algunos de los últimos productos de Oracle en éste área.Siempre tendemos a pensar que en España estamos retrasados en estas tecnologías y que el mercado no está preparado para eliminar el papel. En algunos casos es cierto, pero también nos hemos llevado sorpresas con clientes extremadamente avanzados en la gestión electrónica del papel.Para los clientes que no tienen una solución corporativa ya desplegada, nuestra oferta de Imaging les parece completa e integrada, porque les permite digitalizar el papel en el punto más cercano a su recepción y posteriormente realizar todo el trámite interno de forma digital.Este proceso es el que se muestra en la siguiente imágen: Sobre todo en el entorno financiero los clientes ya tienen grandes infraestructuras desplegadas (algunos con funcionalidades muy sofisticadas que han desarrollado a medida durante estos últimos años).En estos casos, su interés está centrado en 2 capacidades clave de nuestros productos: La digitalización distribuidaEl OCR inteligenteCuando ya disponemos de una infraestructura de digitalización centralizada, tenemos varios puntos de mejora con los que conseguir mayores ratios de ahorro en la gestión del papel. Uno de ellos es digitalizar en origen, de forma que ahorraremos en logística de desplazamiento y almacenamiento de papel (reducimos valijas) y en velocidad de arranque de los procesos (desde el momento de la recepción).El hecho de poder hacer esto sólo con un explorador de internet es muy novedoso para los clientes.El no instalar ninguna pieza de software de cliente parece que es un requisito que muchos clientes estaban demandando desde hace tiempo. De hecho, estamos realizando demos en vivo con un escáner del cliente (solo necesitamos el driver de windows para ese escáner). El resultado es sorprendente porque mostramos cómo: escaneamos con sólo un explorador de internet; el documento escaneado, con sus metadatos, se incorporan al gestor documental; y se dispara su workflow de aprobación.Hacer esto en segundos es algo que genera mucho interés en los clientes de cara a acelerar la gestión de muchos de sus trámites en papel.Por último, lo más novedoso de la oferta es el OCR inteligente. Hay quien ya tiene absolutamente operativas sus infraestructuras de digitalización con todas estas capacidades, y buscan un paso más allá con el reconocimiento inteligente de todos los metadatos posibles.El beneficio es rápido, claramente cuantificable y muy alto. El software de OCR inteligente se basa en lógica difusa y nos permite definir los umbrales de validación totalmente adecuados a nuestros factores de confianza. Es decir, configuramos el umbral para que cuando el software acepta un acierto tengamos la seguridad total de que dichos metadatos se han reconocido perfectamente. En caso contrario, el software lanza una validación manual.¿Qué pasa si conseguimos que para determinados documentos, el 40%, 50%, 60% o incluso el 70% u 80% de ellos fueran procesados 100% automáticamente?. El ahorro es inmenso, la reducción del tiempo de proceso también, y la integración con nuestras infraestructuras de digitalización es muy sencilla (basta con desviar unos cuantos documentos de un tipo concreto a Oracle Forms Recognition y evaluar el resultado).Os animo a que veáis estos productos y consigamos hacer realidad la reducción de papel.

    Read the article

  • Cut Caseload Costs, Speed Service Delivery For Social Services

    - by michael.seback
    Lower Caseload Costs, Speedier Service Delivery with New Oracle Social Services Solution Oracle has just introduced a new solution for social services agencies that's designed to help case workers address the challenges of rising workloads and growing demands by citizens for additional services. In the past, IT departments developed custom software in an effort to meet program outcomes. "Because this capability is out of the box with the Oracle solution, there's less complexity for organizations and an overall lower total cost of ownership," says Kimberly Ellison-Taylor, Oracle's executive director of health and human services. "Self service brings costs down to just pennies per interaction and makes it possible for clients to receive government services more quickly," Ellison-Taylor says. read more

    Read the article

  • Welcome Relief

    - by michael.seback
    Government organizations are experiencing unprecedented demand for social services. The current economy continues to put immense stress on social service organizations. Increased need for food assistance, employment security, housing aid and other critical services is keeping agencies busier than ever. ... The Kansas Department of Labor (KDOL) uses Oracle's social services solution in its employment security program. KDOL has used Siebel Customer Relationship Management (CRM) for nearly a decade, and recently purchased Oracle Policy Automation to improve its services even further. KDOL implemented Siebel CRM in 2002, and has expanded its use of it over the years. The agency started with Siebel CRM in the call center and later moved it into case management. Siebel CRM has been a strong foundation for KDOL in the face of rising demand for unemployment benefits, numerous labor-related law changes, and an evolving IT environment. ... The result has been better service for constituents. "It's really enabled our staff to be more effective in serving clients," said Hubka. That's a trend the department plans to continue. "We're 100 percent down the path of Siebel, in terms of what we're doing in the future," Hubka added. "Their vision is very much in line with what we're planning on doing ourselves." ... Community Services is the leading agency responsible for the safety and well-being of children and young people within Australia's New South Wales (NSW) Government. Already a longtime Oracle Case Management user, Community Services recently implemented Oracle Policy Automation to ensure accurate, consistent decisions in the management of child safety. "Oracle Policy Automation has helped to provide a vehicle for the consistent application of the Government's 'Keep Them Safe' child protection action plan," said Kerry Holling, CIO for Community Services. "We believe this approach is a world-first in the structured decisionmaking space for child protection and we believe our department is setting an example that other child protection agencies will replicate." ... Read the full case study here.

    Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >