Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 53/370 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• Getting WLAN on my Laptop to work (Medion MD98300)

  - by Anand Böhmer

  Dear Ubuntu Community, I am having difficulties to get the WLAN Adapter on my Medion 98300 Laptop to work. The WLAN Card seems to be connected through an internal USB Interface and the Card itself had shown up as a wirelles Network while installing Ubuntu. I have tried a few things earlier, but none of my google reasearches have brought me to a working solution... I am quite new to the Linux System and only knoew a couple of terminal commands so far, so I probably have missed out on a few possible solutions. Maybe you can help me? Thank you very much in advance! A fre minimal technical Details: AMD Turion 64 X2 Dual-Core Mobile Technolgie TL-50 NVIDIA GeForce Go 6150 SanDisk 64GB SSD 2GB RAM DDR2 667 nForce Chipset (I forgt the Version, but deductable from the GPU I guess) WiFi: ZyDAS ZD1211B 802.11g Thank's a lot again! :) UPDATE: I tried around myself a little and found a guide on the Linux Mint forums that helped! I already had tried to install the linux backport modules etc. What I finally did was update the linux firmware and run the following command: echo "options acer_wmi wirelles=1" sudo tee /etc/modprobe.d/acer_wmi.conf and rebooted now I found and could connect to networks, but unfortunately I found, that the link quality was very bad, around 40 to 50. Eventhough my Router is running at high power and is only 6 Meters away! I then switched a few channels, but that did not improve much. Before, under Windows, I had a very good link quality and had the entire 16mbit/s internet connection at disposal, now I can only get about 3-5Mbit/s. better then nothing, but still pretty bad! The "TX power" is fixed on 20dBm and iwconfig says, that the "Power Management" is off... Maybe the power of the module is set too low?... UPDATE2: I figured that 20dBm is a normal power output. I even tried to change the power using iwconfig wlan0 txpower INTEGERHERE but, obviously my "Card" does not support more then 20. More would probably be illegal as well, so I won't even use more then 20. I guess that I will have to figure out a way, or maybe just switch cards. Are the Mailboard-USB-Connectors on a laptop of the same property as the standard external ones? If so, I could simply solder a micro Wirelless N Adapter onto the board :)

  Read the article

• How do I format the output of nmap to display on conky?

  - by WolfLarson

  I want to add to the network section of conky a list of all hosts and ips for my network. However I do not know how to format the output in a way I like. I want Live Hosts However this is on the bottom line of nmap's output) host (ip) host (ip) and on and on... I think there should be a max of 7 on my network. How can I do this? The output of nmap -sP 192.168.1.0/24 looks nothing like what I want though it does have all the parts, just in the wrong order.

  Read the article

• Copy all bridge traffic to a specific interface

  - by Azendale

  I have a bridge/switch set up an a machine that has multiple ports. Occasionally, I have a vm running through virtualbox, and I'll have it use a virtual adapter and then I add the adapter to the bridge. I have heard that some switches can copy all the traffic they see to a specific port on the bridge, usually for network monitoring. I would like to be able to run some windows based network tools. I do not want to run Windows on the actual hardware, because it would be lots of work to duplicate my setup in windows, so I was thinking if I can copy all traffic to a port, I can send it to a VM with windows. How can I set this up? I think this might be ebtables area, but I don't know ebtables well enough to know for sure, and it always seems like (from my understanding of ebtables) ebtables does something with the traffic (drop, accept, etc), but never copies it.

  Read the article

• Cant get internet connection at all on Ubuntu 13.04

  - by James Ellis

  I installed Ubuntu 13.04 alongside my Windows Vista, at the start of installation it doesn't connect to the internet to download updates during installation, also during installation towards the end it removes a lot of stuff that i couldn't catch the details of at the time, it won't find my internet connection even though windows does, i tried using the ethernet cable but it wouldn't pick that up either. So i clicked in Ubuntu... System, network-Browse Internet, then Windows Internet and it said "failed to retrieve share list from server:no such file or directory" how can i get Ubuntu to find my internet???

  Read the article

• compiling compat-wireless fails at 'make' with 'make: *** [modules] Error 2'

  - by Paul Carter

  Trying to compile the compat-wireless-2012-09-25 driver module, without success. scrips/driver-select alx ; works make ; fails - scripts/Makefile.build:44 ~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: ** No rule to make target '~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile'. Stop. [snip] make: * [modules] Error 2 Device is Atheros AR8161 wired ethernet in a Dell Vostro 3460. I'd be very grateful for assistance in getting this to compile.

  Read the article

• make my Ubuntu 12.04 laptop visible on the network

  - by Andrew Boyd

  I'm ecstatically happy with my 12.04 on my laptop after loading it over my MS Vista... but there's just one thing, one little fly in the ointment.... While I can view our 2 Terabyte, shared hard-drive in the lounge (and copy files back and forth) I can't see my PC (when I boot up in Ubuntu 12.04) nor the Lubuntu computer connected to the TV (for movies, Youtube etc). Printing to the HP office jet on the PC doesnt work over the network either. Have had one dubious flirtation with Samba, which seems to be the only thing I've found that will 'work', however halfway through that "installation" everything just ground to a halt, the directions began to stop making sense... I was working from this page. Our Network consists of the following: Our Internet service is wirelessly sent to us from our provider to our dish on a pole. It comes into the house via an ethernet cable. We split it there to a phone, and to 6 other destinations (bedrooms, computers, and to another splitter in the lounge which has a wifi antennae and 4 ethernet ports). one port goes to the Lubuntu OS PC which is connected to the TV the second port goes to the 2 Terabyte harddrive (MS powered 'Mybooklive') (the other two are empty) My Ubuntu 12.04 laptop connects wirelessly to this splitter in the lounge. I know just enough about computers to get myself into an awful mess without too much trouble We usually can view friends' laptops when they get on our network (as they are invariably MS OS's) Our flatmate, who introduced us to Linux's computer is also invisible How can we make our Linux OS based computers visible on the network and share files and printing?

  Read the article

• How do I run my XBOX XNA game without a network connection?

  - by Hugh

  I need to demo my XBOX XNA game in college. The college doesn't allow this type of device to connect to the network. I deployed my game to the Xbox and it is sitting in the games list along with my other games. It runs fine with a network connection but when its offline it comes up with an error message saying its needs a connection to run the game. This makes no sense, the game is deployed on the Xbox memory, it must be some security policy or something! Is there any way around this? The demo is on monday!

  Read the article

• Cannot ping router with a static IP assigned?

  - by Uriah

  Alright. I am running Ubuntu LTS 12.04 and am trying to configure a local caching/master DNS server so I am using Bind9. First, here are some things via default DHCP: /etc/network/interfaces cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The primary network interface - STATIC #auto eth0 #iface eth0 inet static # address 192.168.2.113 # netmask 255.255.255.0 # network 192.168.2.0 # broadcast 192.168.2.255 # gateway 192.168.2.1 # dns-search uclemmer.net # dns-nameservers 192.168.2.113 8.8.8.8 /etc/resolv.conf cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 192.168.2.1 search uclemmer.net ifconfig ifconfig eth0 Link encap:Ethernet HWaddr 00:14:2a:82:d4:9e inet addr:192.168.2.103 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::214:2aff:fe82:d49e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1067 errors:0 dropped:0 overruns:0 frame:0 TX packets:2504 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:153833 (153.8 KB) TX bytes:214129 (214.1 KB) Interrupt:23 Base address:0x8800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:915 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:71643 (71.6 KB) TX bytes:71643 (71.6 KB) ping ping -c 4 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. 64 bytes from 192.168.2.1: icmp_req=1 ttl=64 time=0.368 ms 64 bytes from 192.168.2.1: icmp_req=2 ttl=64 time=0.224 ms 64 bytes from 192.168.2.1: icmp_req=3 ttl=64 time=0.216 ms 64 bytes from 192.168.2.1: icmp_req=4 ttl=64 time=0.237 ms --- 192.168.2.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.216/0.261/0.368/0.063 ms ping -c 4 google.com PING google.com (74.125.134.102) 56(84) bytes of data. 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=1 ttl=48 time=15.1 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=2 ttl=48 time=11.4 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=3 ttl=48 time=11.6 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=4 ttl=48 time=11.5 ms --- google.com ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 11.488/12.465/15.118/1.537 ms ip route ip route default via 192.168.2.1 dev eth0 metric 100 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.103 As you can see, with DHCP everything seems to work fine. Now, here are things with static IP: /etc/network/interfaces cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # The primary network interface - STATIC auto eth0 iface eth0 inet static address 192.168.2.113 netmask 255.255.255.0 network 192.168.2.0 broadcast 192.168.2.255 gateway 192.168.2.1 dns-search uclemmer.net dns-nameservers 192.168.2.1 8.8.8.8 I have tried dns-nameservers in various combos of *.2.1, *.2.113, and other reliable, public nameservers. /etc/resolv.conf cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 192.168.2.1 nameserver 8.8.8.8 search uclemmer.net Obviously, when I change the nameservers in the /etc/network/interfaces file, the nameservers change here too. ifconfig ifconfig eth0 Link encap:Ethernet HWaddr 00:14:2a:82:d4:9e inet addr:192.168.2.113 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::214:2aff:fe82:d49e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1707 errors:0 dropped:0 overruns:0 frame:0 TX packets:2906 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:226230 (226.2 KB) TX bytes:263497 (263.4 KB) Interrupt:23 Base address:0x8800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:985 errors:0 dropped:0 overruns:0 frame:0 TX packets:985 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:78625 (78.6 KB) TX bytes:78625 (78.6 KB) ping ping -c 4 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. --- 192.168.2.1 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms ping -c 4 google.com ping: unknown host google.com Lastly, here are my bind zone files: /etc/bind/named.conf.options cat /etc/bind/named.conf.options options { directory "/etc/bind"; // // // query-source address * port 53; notify-source * port 53; transfer-source * port 53; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; forwarders { // My local 192.168.2.113; // Comcast 75.75.75.75; 75.75.76.76; // Google 8.8.8.8; 8.8.4.4; // DNSAdvantage 156.154.70.1; 156.154.71.1; // OpenDNS 208.67.222.222; 208.67.220.220; // Norton 198.153.192.1; 198.153.194.1; // Verizon 4.2.2.1; 4.2.2.2; 4.2.2.3; 4.2.2.4; 4.2.2.5; 4.2.2.6; // Scrubit 67.138.54.100; 207.255.209.66; }; // // // //allow-query { localhost; 192.168.2.0/24; }; //allow-transfer { localhost; 192.168.2.113; }; //also-notify { 192.168.2.113; }; //allow-recursion { localhost; 192.168.2.0/24; }; //======================================================================== // If BIND logs error messages about the root key being expired, // you will need to update your keys. See https://www.isc.org/bind-keys //======================================================================== dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.local cat /etc/bind/named.conf.local // // Do any local configuration here // // Consider adding the 1918 zones here, if they are not used in your // organization //include "/etc/bind/zones.rfc1918"; zone "example.com" { type master; file "/etc/bind/zones/db.example.com"; }; zone "2.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/db.2.168.192.in-addr.arpa"; /etc/bind/zones/db.example.com cat /etc/bind/zones/db.example.com ; ; BIND data file for example.com interface ; $TTL 604800 @ IN SOA yossarian.example.com. root.example.com. ( 1343171970 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS yossarian.example.com. @ IN A 192.168.2.113 @ IN AAAA ::1 @ IN MX 10 yossarian.example.com. ; yossarian IN A 192.168.2.113 router IN A 192.168.2.1 printer IN A 192.168.2.200 ; ns01 IN CNAME yossarian.example.com. www IN CNAME yossarian.example.com. ftp IN CNAME yossarian.example.com. ldap IN CNAME yossarian.example.com. mail IN CNAME yossarian.example.com. /etc/bind/zones/db.2.168.192.in-addr.arpa cat /etc/bind/zones/db.2.168.192.in-addr.arpa ; ; BIND reverse data file for 2.168.192.in-addr interface ; $TTL 604800 @ IN SOA yossarian.example.com. root.example.com. ( 1343171970 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS yossarian.example.com. @ IN A 255.255.255.0 ; 113 IN PTR yossarian.example.com. 1 IN PTR router.example.com. 200 IN PTR printer.example.com. ip route ip route default via 192.168.2.1 dev eth0 metric 100 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.113 I can SSH in to the machine locally at *.2.113 or at whatever address is dynamically assigned when in DHCP "mode". *2.113 is in my router's range and I have ports open and forwarding to the server. Pinging is enabled on the router too. I briefly had a static configuration working but it died after the first reboot. Please let me know what other info you might need. I am beyond frustrated/baffled.

  Read the article

• What is the correct way to restart udev in Ubuntu?

  - by zerkms

  I've changed the name of my eth1 interface to eth0. How to ask udev now to re-read the config? service udev restart and udevadm control --reload-rules don't help. So is there any valid way except of rebooting? (yes, reboot helps with this issue) UPD: yes, I know I should prepend the commands with sudo, but either one I posted above changes nothing in ifconfig -a output: I still see eth1, not eth0. UPD 2: I just changed the NAME property of udev-rule line. Don't know any reason for this to be ineffective. There is no any error in executing of both commands I've posted above, but they just don't change actual interface name in ifconfig -a output. If I perform reboot - then interface name changes as expected. UPD 3: let I explain all the case better ;-) For development purposes I write some script that clones virtual machines (VirtualBox-driven) and pre-sets them up in some way. So I perform a command to clone VM, start it and as long as network interface MAC is changed - udev adds the second rule to network persistent rules. Right after machine is booted for the first time there are 2 rules: eth0, which does not exist, as long as it existed in the original VM image MAC eth1, which exists, but all the configuration in all files refers to eth0, so it is not that good for me So I with sed delete the line with eth0 (it is obsolete and useless in cloned image) and replace eth1 with eth0. So currently I have valid persistent rule, but there is still eth1 in /dev. The issue: I don't want to reboot the machine (it will take another time, which is not good thing on building-VM-stage) and just want to have my /dev rebuilt with some command so I have ready-to-use VM without any reboots.

  Read the article

• Fair dice over network w/o trusted 3rd party

  - by Kay

  Though it should be a pretty basic problem, I did not find a solution for it: How to play dice over a network without a trusted third party? The M players shall roll N dice, one player after another. No player may "cheat", i.e. change the outcome to his advantage, or "look into the future" before the next roll. Is that possible? I guess the solution would be something like public key crypto, where each player turns in an encrypted message. After all messages were collected you exchange the keys to decode the messages. Then the sha1(joined string of all decrypted messages) mod 6 + 1 is used to determine the die. The major problem I have: since the message [c/s]hould be anything, I don't know how to prevent tampering with the private keys. Esp. the last player to turn in his key could easily cheat (I guess). The game should even stay fair, if all players "conspire" against one player.

  Read the article

• Network traffic monitoring for unexperienced users

  - by Eduardo Casteluci

  I'm a really unexperienced Ubuntu user and I'm having a hard time monitoring my network traffic. I just need to know what websites each one of the devices connected to my network are accessing. I've tried to use ntop, but I couldn't work around it. Is that possible? I mean, is it possible to know that kind of data only by specifing a local IP address? How can I do that? It's a security issue that I'm facing and I need to work that "easy" monitoring out. Thanks

  Read the article

• How to prevent WLAN connection from dropping permanently on a Fritz USB WLAN N stick?

  - by Chris

  I have a desktop with a Fritz USB WLAN N stick and tried Ubuntu 12.04. Installation went fine and WLAN is working. However, connection drops permanent. Reconnecting manually fixes it but after a few minutes it drops again. It's connected to a Vodafone 802 box with WLAN N fix set. It seems that it works when I switch off N mode. But I need to test. Can someone confirm this issue or is there another solution? I have another machine with 12.04 (HP 625 laptop) running where connection is stable.

  Read the article

• Connect WPA networks using Broadcom BCM4315

  - by Natim

  I just installed Ubuntu 14.04 LTS on my HP computer I installed the BCM43 driver I used @Wild Man script to get you some informations: wget -N -t 5 -T 10 http://dl.dropbox.com/u/57264241/wireless_script && chmod +x wireless_script && ./wireless_script Here: http://paste.lolnet.org/paste/kOil1BvT#psOHgxeF As you can see on the file, everything looks good, WEP,WPA,WPA2 but my wifi which is a WPA-PSK password doesn't appears on the network list. Do you have any idea of what could be wrong?

  Read the article

• Akka react vs receive

  - by Will I Am

  I am reading my way through Akka tutorials, but I'd like to get my feet wet with a real-life scenario. I'd like to write both a connectionless UDP server (an echo/ping-pong service) and a TCP server (also an echo service, but it keeps the connection open after it replies). My first question is, is this a good experimental use case for Akka, or am I better served with more common paradigms like IOCP? Would you do something like this with Akka in production? Although I understand conceptually the difference between react() and receive(), I struggle to choose one or the other for the two models. In the UDP model, there is no concept of who the sender is on the server, once the pong is sent, so should I use receive()? In the TCP model, the connection is maintained on the server after the pong, so should I use react()? If someone could give me some guidance, and maybe an opinion on how you'd design these two use cases, it would take me a long way. I have found a number of examples, but they didn't have explanations as to why they chose the paradigms they did.

  Read the article

• Ubuntu systematically losing wired connection

  - by Lukasz Baczynski

  I'm working on 11.10 for few recent days, everything was working perfect until today. Updated ubuntu (some certs were updates as far as i remember) and from this time, wired network stops working randomly and systematically. (All other pcs/macs work fine) From 192.168.0.9 icmp_seq=25 Destination Host Unreachable From 192.168.0.9 icmp_seq=26 Destination Host Unreachable From 192.168.0.9 icmp_seq=27 Destination Host Unreachable From 192.168.0.9 icmp_seq=28 Destination Host Unreachable From 192.168.0.9 icmp_seq=29 Destination Host Unreachable From 192.168.0.9 icmp_seq=30 Destination Host Unreachable From 192.168.0.9 icmp_seq=31 Destination Host Unreachable 64 bytes from 192.168.0.1: icmp_req=32 ttl=64 time=1003 ms 64 bytes from 192.168.0.1: icmp_req=33 ttl=64 time=0.496 ms 64 bytes from 192.168.0.1: icmp_req=34 ttl=64 time=0.576 ms 64 bytes from 192.168.0.1: icmp_req=35 ttl=64 time=0.522 ms 64 bytes from 192.168.0.1: icmp_req=36 ttl=64 time=0.624 ms 64 bytes from 192.168.0.1: icmp_req=37 ttl=64 time=0.625 ms 64 bytes from 192.168.0.1: icmp_req=38 ttl=64 time=0.555 ms It'll work for 20 seconds then it'll stop working for 10-30sec and so on. I've tried setting my router to give static IPs, it doesn't help. NOTHING has been changed since yesterday beside the package update... Here are other settings that may be useful: baka@baka-PC:~/Private/projects/wduk$ lspci -nnk | grep -iA2 net 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432] Kernel driver in use: r8169 baka@baka-PC:~/Private/projects/wduk$ ifconfig -a eth0 Link encap:Ethernet HWaddr **Removed MAC address** inet addr:192.168.0.9 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:fe0a:85b2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6400 errors:0 dropped:6400 overruns:0 frame:6400 TX packets:7085 errors:0 dropped:107 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4191983 (4.1 MB) TX bytes:886881 (886.8 KB) Interrupt:72 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2522 errors:0 dropped:0 overruns:0 frame:0 TX packets:2522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1070130 (1.0 MB) TX bytes:1070130 (1.0 MB) baka@baka-PC:~/Private/projects/wduk$ cat /etc/resolv.conf # Generated by NetworkManager nameserver 8.8.8.8 thanks for help

  Read the article

• Install VirtualBox Guest Additions "Feisty Fawn"

  - by codebone

  I am trying to install the virtualbox guest additions into a feisty fawn (7.04) VM. The problem I am running into is that when I Click install guest additions, or place the iso in the drive manually, the disk never shows up in the machine. I even manually mounted and went to the mounted directory and it was empty. When using the file browser, doubling clicking on the cdrom yields Unable to mount the selected volume. mount: special device /dev/hdc does not exist. Secondly, I tried installing via repository... but according to the system, I have no internet connection. But, I can browse the web using firefox just fine (in the guest). Here is my /etc/network/interfaces file... code auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp I also tryed setting a static ip... auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.253 netmask 255.255.255.0 gateway 192.168.1.1 The reason I am trying to get this particular installation running is because it is part of a book, "Hacking: The Art of Exploitation" (Jon Erickson), and is fully loaded wilh tools and such to go along exactly with the book. I appreciate any effort into finding a solution for this! Thanks

  Read the article

• How to promote/market an event that needs many people?

  - by stjowa

  My team is about to launch a new web application, http://wethepixels.com, that requires a lot of people to be on the site at the same time for the concept to be successful. Our team is preparing to promote/market an event for a specific date and time, in order to try to grab a large group of people to the site at once. For those who have gone through a similar web launch, we would love to hear ideas on the best way to market for a large group in a relatively short period of time. We have created a Facebook page and a Facebook event, but it has yet to grab much attention (surprisingly to us). Is there a better way to attract a large number of users in a short period of time? Thanks

  Read the article

• Can't connect to WIFI after sleep Ubuntu 14.04

  - by user3380404

  After an upgrade over a previous version to Ubuntu 14.04 I have problems with connecting to WiFi. After suspending it won't reconnect to any existing network unless I restart the laptop. sudo lshw -C network: *-network description: Ethernet interface product: 82567LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:27:13:b4:d3:58 capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=2.3.2-k firmware=1.8-3 latency=0 link=no multicast=yes port=twisted pair resources: irq:45 memory:fc200000-fc21ffff memory:fc225000-fc225fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:c6:6b:c8 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-29-generic firmware=8.83.5.1 build 33692 ip=10.0.1.160 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:48 memory:f4200000-f4201fff

  Read the article

• Slow boot on Ubuntu 12.04, probable cause the network connection

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• Network icon shows an Internet connection, while ping does not

  - by mushfiq

  I am an Ubuntu user for the last couple of years. Recently facing problem to connect my new laptop into the Internet. I have an ISP connection which provide me a NAT address. I changed all the information in network configuration.The network icon shows it is connected to Internet but when I browse, ping shows no Internet connection. /etc/network/interfaces look like this: auto eth0 iface eth0 inet static address 192.168.100.118(put you internet address provided by the ISP) gateway 192.168.100.1(gateway address) netmask 255.255.255.0 network 192.168.100.0 And when I ping my DNS server IP get the reply from DNS server. I can not understand the problem,it should be mentioned that I also changed the Physical address of my laptop for using the existing connection. In windows the connection is working fine. Any suggestion in this question will help me a lot. Thanks in advance.

  Read the article

• Bash script won't stay open in background after running through while

  - by jfreak53

  I can't get the following bash script to stay open after the first message is received from NC: #!/bin/bash port=3333 nc -l $port | while read msg; do notify-send Alert "$msg"; done After the first message it exits. I want it to stay open and continue monitoring for new messages from NC. I know that if I launch nc -l port without the while loop it stays open and I can chat away between the two connections even disconnect from the connected host. I am sending the message using: echo 'done' | nc IP port

  Read the article

• Wi-fi interface fails to authenticate on secured networks

  - by Eduardo Bezerra

  the problem is that I can't connect to wireless networks that have security enabled. I can connect fine to the unsecured network of my university, but not to the secured one in the same building. Also, it fails to connect to my home wireless router, which uses wpa2 encryption. Any ideas? I have a Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01), with pci id [14e4:4353], running Ubuntu 12.10 on a macbook pro 6,2. I'm using bcmwl-kernel-source package with kernel module wl to enable my wi-fi device.

  Read the article

• MaaS minimum requirements with juju-jitsu?

  - by Christopher Shen Mu Long

  I've browsed through so many different sites and found so much contradictory information. As I am getting tired of this and do belive this question affects many other users, so I would like to collect the "once and for all times" answer. Unfortunately, the documentation on MaaS and Juju is ... well, not the best, sorry to say that. What are the minimum system requirements for setting up a MaaS cluster, which is going to be orchestrated with juju-jitsu? Do they need to have the exact system specifications or can I just combine different hardware? What are the minimum requirements for the master machine? E.g. "You need at least 8GB of RAM, a dual core CPU with at least 3.0 GHz." How many machines to I need to deploy MaaS on? I've read six machines, nine machines, and so on. I clearly want to know: "You need one for the Master and e.g. five nodes." Do I need to attach as many NICs (network interface cards) to my master machine as there are nodes, or can I simply attach two NICs and a switch? One NIC for connecting to the internet, one for handling the MaaS tasks, connected to a switch, which connects my nodes to the master? Is Juju now ready for local deployment? The last time I experimented with juju and had to reboot my machine, the services orchestrated by juju were gone. This was an issue I also found on the official juju site. Unfortunately, as mentioned above, the documentation is not the best, so I could not find the necessary info on that again. So: Can I use juju on a local environment or will a reboot break my setup?

  Read the article

• Suddely internet is not accessible

  - by user189708

  I am going crazy here. One day everything was working fine. I turned pc off and went to sleep. Next day turn pc on and cannot access internet (from any browser). The situation is: I cannot open any webpage from browser (tried Firefox and Epiphany) and cannot receive emails in thunderbird. BUT if I run firefox from console as sudo, I can use it as usual. I can access Skype and pretty much any other network stuff (like installing software with apt-get etc.), also if I use Astrill VPN software I can access webpages even running without sudo. I haven't install any software or anything like that for several days = I have not a clue what could cause this. Just by the way, other Win PC in our home has no issue. Here is what I have tried to fix this: I have tried to restart my pc, router, modem - multiple times I have tried to change permissions to my firefox profile I have tried to completely re-install firefox and start with blank profile, thus no addons I have tried to change /etc/resolv.conf to an IP of my router (it was 127.0.1.1) I have tried to change my hostname (from tomino-NB to tominoNB) I think I might try even more stuff. None of it works. Can someone please try to help me. Thank you UPDATE 1: I have tried this: Removing resolv.conf - Didn't help Also "ping" and "dig" commands cannot resolve host UPDATE 2: I have tried to edit nameservers in resolv.conf but still no effect. I can ping router as well as I can ping outside IP. So definitely just some DNS issue. Is it possible that something is rewriting path to resolv.conf and using different file? UPDATE 3: I have just restarted PC and everything works now... resolv.conf went back to nameserver 127.0.1.1 . I have no clue what happened that it works again...

  Read the article

• Frequent disconnects with oneiric server using wlan AR9285

  - by John Neil

  I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >