Search Results

Search found 26223 results on 1049 pages for 'visual c 2008 express'.

Page 53/1049 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• After upgrading to 2008 R2 Enterprise and installing more RAM, Windows can only see 4.00 GB

  - by Tom Crane

  (I have also posted this on technet but I'm running out of ideas) I've upgraded from Windows Server 2008 R2 Standard to Enterprise in order to make use of more RAM. The server previously had 32GB of RAM. The upgrade from Standard to Enterprise, using DISM, seemed to go OK, so I powered down and installed the RAM. This a Dell Poweredge T710, I was taking it from 32GB to 72GB. The BIOS recognised the RAM, although I needed to change from "Advanced ECC" to "Optimizer" mode for it to use all of it. After rebooting, windows can see the RAM but in the system panel will display: Installed memory (RAM): 72.0 GB (4.00 GB usable) In the resource monitor, the remainder of the RAM is showing as reserved for hardware. I've tried various RAM configurations, including reverting it to the same chips and same configuration as before the upgrade, but always just 4.00 GB is showing up as usable. Following some threads on these forums I've gone into msconfig and set the maximum memory "by hand" but that doesn't fix the problem. BIOS doesn't seem to have anything that looks like memory remapping which is another suggestion that has come up. How do I make this RAM available to Windows? It was available before the upgrade, because I could use the full 32GB RAM the server had to start with. A screenshot (this is after reverting to the original RAM configuration) http://screencast.com/t/5FuzevdNb I don't know if it's related, but my remote desktop configuration has also disappeared: screencast.com/t/mYedomeQWS (the bottom half of this dialog should allow me to configure Remote Desktop, it was working before the upgrade but now it isn't).

  Read the article

• Upgrade SQLServer 2008 hardware

  - by John

  Forgive me if I'm not able to be totally clear here. It is not intentional, I'm a senior level developer in a very small company having to act like a manager at the moment. Anyway, the story is that we have 2 older dell servers with SQL Server 2008 Standard in a "cluster". I put that in quotes because I'm still not 100% clear what that means. We have 2 brand new blade servers and want to move the existing databases to the new hardware. Ok, so here is the gotcha. We need to do this with little or no down time. I'm being told that we can evict the passive node, then pull in one of the new servers. But I'm also being told that this is a dangerous step because something could go wrong that would cause the cluster to fail and then we would be left with nothing because the active server would not be able to come back up. Does anyone have any thoughts on how to handle this? I'm being told that the only way to ensure success is to have at least a day of down time where we bring up a new cluster on the new hardware and then migrate the databases 1 by 1.

  Read the article

• Windows Server 2008 R2 running at a snail's pace

  - by Django Reinhardt

  Really weird problem here. Our main web server has started running at a snail's pace, for absolutely no reason we can discern. Even after restarting the machine, when there's no little or no ram usage and CPU usage is fluctuating between 0 and 30%, simple tasks, like opening Internet Explorer, or waiting for My Computer to open, take forever. There are no processes hogging system resources that we can see... the machine itself is just exhibiting extremely slow behaviour. I've never seen a machine do this. A lot of security updates had built up, so we decided to let Windows install them. When we looked through the history upon restarting, though, they had failed with error code 800706BA. I don't know if this could be related or not. Any help in this matter would be greatly appreciated. As mentioned in the title, we're running a Windows Server 2008 R2 machine. It's also running SQL Server and IIS. It has 16GB of RAM and a decent Quad Core processor. It's also been fine until now -- and we haven't changed a thing. Thanks for any help.

  Read the article

• best practices for setting up a new windows 2008 R2 server with ec2 AWS

  - by Alex

  Can someone comment what they would add to the following list of SOP in terms of best practices? This is being set up on AWS, and then after further testing, back in our datacenter. Standard Operation Procedure (SOP): Installation Part: 2 - Installation of Software Components in Windows 2008 R2 (Updated). Step: 1 Logon to the host through Remote Desktop. Strp: 2 Open Server Manager - Server Roles - Install Web Server IIS 7.5 with compatible of IIS 6 features and Management compatibility mode. Step: 3 Open IE/Mozilla to Download the below listed software's and save all installation files to folder called "AWS Server Install Files" for future reference.. Net Framework 2.0 (Download that from internet) Crystal reports for .Net Framework 2.0 (x64) (Download that from internet) SQL Server 2005 (AWS Image) Step: 4 Once all software's saved on local drive, then Install it one by one. Step: 5 Navigate to Desktop folder to install the below listed softwares. Microsoft Asp.net 2.0 AjaxExtention 1.0 (placed on Desktop \Softwares) WebEx recorder. (placed on Desktop \Softwares) Winrar(placed on Desktop \Softwares) Step: 6 Make sure all the software are working fine. Step: 7 Inspect the server once entirely. Step: 8 Logoff & Stop the Instance.

  Read the article

• Server 2008 R2 domain windows update strategy

  - by Joost Verdaasdonk

  Let me explain my question a bit. We are a small company that have now made the first move to a bigger network. For now the network contains of 5 servers 2008 R2 (dc,sql,web,etc..). Everything we need is now in place but for now we cannot afford to finish the network by implementing redundant systems. (secondary dc, dns, sql cluster, etc...) For some people this is hard to understand but this is the current situation. (and we are aware and will fix this when we can) Because we want to keep our system secure and up to date I've made sure that all systems are updated regularly. The problem is ofc that the nr of updates Microsoft rolls out that need a system reboot seam to occur more often. (maybe I'm wrong and it just feels like this) ;-) In our domain servers depend on each other for services (like SQL, WEB, or whatever) so just rebooting a server at will is NOT a good idea! For now I update all of them without rebooting at once. After all are up to date I bring them down in the order they are depended on each other. After this I reboot all of them in the inverse order. I understand ofc that if I DID have redundancy in my system that updating and rebooting would not be such a problem because the server task could be taken over by another node but this is something we generally need to add when we can. So my question is. If you read my above situation can you suggest me more Update strategies or general ideas that could help me do this process in a better / faster way? Thanks for your thoughts!

  Read the article

• Install MS Office on Windows Server 2008 - in support of Quickbooks RemoteApp

  - by steampowered

  How can I install MS Office on Windows Server 2008? The purpose would be to enable Quickbooks to be able to export to Excel. Quickbooks is set up to run as a RemoteApp in a Terminal Server environment. The Quickbooks applicaiton senses whether or not Excel is installed and will not allow the user to create an Excel report unless Excel is actually installed on the client running Quickbooks. Since the client and the server are the same machine in a Terminal Server environment, Excel must be installed on Windows Server for the Quickbooks Excel exporting feature to work in this setup. There is no need to actually use Excel in a Terminal Services environment. We only need to generate the Excel files using the server, then we can use an installed version Excel on a regular Windows 7 machine to work with the Excel file. MS Office does not normally install on Windows Server. Is there any way to buy a special license? Could we somehow fool Quickbooks into thinking Excel is installed, if that would work?

  Read the article

• Windows Server 2008 ignores any change made to firewall

  - by Maurice Courtois

  I have been trying for the last 2 hours to make my Windows Server 2008 answer ping. I have tried almost every single solution I have found on the web, so far nothing work. My current setup: 2 NIC (1x Internet connection, 1x Local network) Server act as VPN server. So I set the corresponding NIC as either Public or Private. I also enable the rule for "File and Printer Sharing (Echo Request...)" for all Nic and from any IPs. I always been able to ping from the local network or the local ip while connected to the VPN. I also tried to create a specific rule for ICMP ping and disabling the firewall for all but the public nic. Regardless of all this, I still can't ping that server from Internet. Any idea suggestion what could cause this? I have the impression that when you set the server as VPN (I switch the box on when setting it up to block everything else than VPN connection) that changing anything to the firewall setting thought mmc is pointless !?!?

  Read the article

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• Unable to connect to second name of Windows 2008 Server R2 machine from XP

  - by Tumba

  I used the command netdom computername /add:newname.domainname.com to add a second name to a server running Windows 2008 Server R2. After restarting the server, I had DNS "A" entries for both names. In addition, the second name was added to HKLM\SYSTEM\CurrentControlSet\services\LanmanServer\Parameters\OptionalNames, which I believe should have taken care of any NetBIOS resolution. From my Windows 7 workstation, I can ping both names and running net view on both names reveals the same list of resources. From Windows XP, I can ping both names, but net view only works on the first name. Running net view on the second name returns: System error 52 has occurred. You were not connected because a duplicate name exists on the network. Go to System in Control Panel to change the computer name and try again. What do I need to do to make the second name usable from XP clients? Update: I was able to resolve the problem by adding the REG_DWORD key DisableStrictNameChecking = 1 to HKLM\SYSTEM\CurrentControlSet\services\LanmanServer\Parameters, then restarting the Server service. However, I do not understand why this was necessary.

  Read the article

• 2008 SR2 Server Starts Then Fails to Initialize DNS

  - by ThaKidd

  Got a weird situation going on. Background: Just transferred Active Directory from a 2003 Server to 2008 SR2. Removed the 2003 server from AD but I have not upgraded Active Directory to 08 only yet. After the transition a problem started. Whenever I reboot the server and I log in, the DNS server is "stopping". After a few minutes it finishes and I can restart start it at that point. Once it is restarted, all services come up. Now I did try to install HyperV (this is a dev server btw). Once the reboot for HyperV, everything was screwed as in I could not ping anything. Uninstalled and had the DNS server issue. Screwed with IPv6 settings (which I am not using) and problem was resolved for a bit. Also installed an Intel Pro1000 card and had a bit of success with DNS; then it failed. Weird thing is, outside of an error in syslog stating that the DNS server failed to start, there is no specific error that is generated in either System or DNS Server logs. Ideas are much appreciated! Thanks in advance.

  Read the article

• How to configure network on Windows Server 2008

  - by Gokhan Ozturk

  I have a IBM x3400 Server Machine with Windows Server 2008 R2 installed on it. But, since I am not expert on networking I have some problems. These roles installed on my server: Active Directory DNS File Sharing Hyper-V ISS VPN There is two network card on them. I configured them like this: Local Connection 1: 192.168.30.3 255.255.255.0 192.168.30.2 127.0.0.1 Local Connection 2: 192.168.30.101 255.255.255.0 192.168.30.6 127.0.0.1 My problem is, when I use this Ip gateways, It is sharing internet to all computers. This is not I want. I want to use Local Connection 1 for internal network. I am giving all computers gateway and DNS IP as 192.168.30.3 The Local Connection 2 is for Hyper-V and VPN connections. 192.168.30.2 and 192.168.30.6 are my modem's gateways. I am using 192.168.30.6 external IP for VPN connections. There is two 24 port switches. There is a connection between them and this two ethernet card connected directly to them. And modems are connected to switches as well (Morems are not near the server. They are somewhere in the building). I disabled network Bridge and removed all ethernet cards from it. With this configuration, all computers can ping my server's IP (192.168.30.3) but on server I cannot ping any clients (Request timeout). What is the best way to configure my network? Thank you. Redgards

  Read the article

• Uninstallation of WSUS form SBS 2008

  - by Logik

  I am not much experienced system admin, but i came across the client who was having SBS 2008. The server was running out of HDD space. So to recover some, I removed its WSUS role (twas not needed).this removed WSUS 3.0 SP1 & freed a lot of space. This SBS is: Domian controller, DNS, DHCP, File server. After i removed WSUS i disabled windows update service & i rebooted serer & checked from one of client if the shared folders are accessible. they were. Next day all of sudden i got call from them saying they can't login into their domain. I looked into server, the Active directory service was stopped. I never remember touching any service other than windows update. How come AD service stopped running all of sudden. Is removing WSUS have such impact? I am not aware of any such thing.

  Read the article

• Windows 2008 Server can't connect to FTP

  - by stivlo

  I have Windows 2008 Server R2, and I am trying to install FTP services. My problem is I can't connect from outside, FileZilla complains with: Error: Connection timed out Error: Could not connect to server Here is what I did. With the Server Manager, I've installed the Roles FTP Server, FTP Service and FTP Extensibility. In Internet Information Services version 7.5, I've chosen Add FTP Site, enabled Basic Authentication, Allow a user to connect Read and Write. In FTP Firewall support on the main server, just after start page, I've set Data Channel Port Range to 49100-49250 and set the external IP Address as the one I see from outside. If I click on FTP IPv4 Address and Domain Restrictions, and click on Edit Feature Settings, I see that access for unspecified clients is set to Allow, so I click OK without changing those defaults. In FTP SSL Policy, I've set to Require SSL connection, certificate is self signed. I tried to connect with FileZilla from the same host and it works, however it doesn't work remotely, as I said above. I've enabled pfirewall.log, but apparently nothing gets logged. The server is in Amazon EC2, and on the security group inbound firewall rules, I've set that ports 21 and ports 49100-49250 accepts connections from everywhere. What else should I be checking to solve the problem?

  Read the article

• Force delivery retry without restarting the SMTP Service on Windows Server 2008 R2

  - by Mathias R. Jessen

  I have a Windows Server 2008 R2 box hosting 3 virtual SMTP servers; vSMTP01, vSMTP02 and vSMTP03. The first two are configured to deliver all messages to dedicated smarthosts, while the last is set to just deliver the messages on its own. All other delivery settings are as default ----(vSMTP01)-----> {SMARTHST01} / ----Inbound mail--->---SMTPSRV01---[----(vSMTP02)-----> {SMARTHST02} \ ----(vSMTP03)-----> { Internet } Now I want to take SMARTHST01 out for maintenance, but I don't want to reject submissions to vSMTP01 while doing so, so I just let it continue running. When SMARTHST01 is no longer responding, vSMTP01 queues the messages and wait for the first retry interval to pass (15 minutes). So far so good. Let's say SMARTHST01 gets online again after 20 minutes. The first interval has passed, and I'll have to wait another 25 minutes for the second retry interval to pass. If I stop and start the SMTP Service (Services.msc - Simple Mail Transfer Protocol service - Stop), the server will retry all deliveries, but that would cause a service interruption for ALL virtual SMTP servers on the machine, which is highly undesirable. How can I manually force vSMTP01 to retry delivery of all queued messages without interrupting the service of vSMTP02 and vSMTP03?

  Read the article

• Server 2008 email on Event variables

  - by Jeff Miles

  One of the new features of Server 2008 is the ability to attach a task to a specific event in the event logs. One of the actions available is to send an email through a SMTP server. This is working great, however it would be ideal if in the message body, the Event contents could be placed. I have tried using $eventdescription and %eventdescription%, but those are just shots in the dark. Any amount of googling produces no results. Does anyone know if this is possible? Update: Sparks' suggestion below is a step in the right direction I believe, however that method doesn't seem to work for all values. For example, I can pull the RecordID, Severity and Channel as shown, but I can't use the same method to retreive the EventID, or most importantly the description. Here's the raw XML from one event: [Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"] [System] [Provider Name="DFSR" /] [EventID Qualifiers="16384"]4412[/EventID] [Level]4[/Level] [Task]0[/Task] [Keywords]0x80000000000000[/Keywords] [TimeCreated SystemTime="2009-05-14T18:18:09.000Z" /] [EventRecordID]45692[/EventRecordID] [Channel]DFS Replication[/Channel] [Computer]servername.domain.com[/Computer] [Security /] [/System] [EventData] [Data]9046C3F4-843E-4A53-B941-4B20764072E5[/Data] [Data]D:\departments\Geomatics\Plan Quality\Data Processing\CG3533017 2009-05-13 KT FIXED[/Data] [Data]D:\departments[/Data] [Data]{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [Data]Departments[/Data] [Data]domain.ca\files\departments[/Data] [Data]B8242CE2-F5EB-47DA-BA5B-1DD2F7EE3AB9[/Data] [Data]DFAA7A54-66CB-4C31-81A0-0F861382C32C[/Data] [Data]CG3533017 2009-05-13-{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [/EventData] [/Event] I have tried using a ValueQuery for EventData, but it returns no data.

  Read the article

• SBS 2008 - DNS Forwarders timing out.

  - by Moif Murphy

  Hello, We have an SBS 2008 server that keeps losing connection to the internet approx 2-3 times a day. It's a simple setup, BT Business Broadband ADSL to a Wireless Zyxel router to the server. Clients connect via WiFi from their laptops. Plugging ethernet in makes no difference, only a reboot of the router seems to bring everything back again. I'm looking at the forwarders on the DNS properties page and they're timing out when trying to resolve the IPs. Currently there are two IPs in there, 194.72.9.34 which has timed out and 194.72.9.38 which has finally resolved to ns8.bt.net We've been in there and replaced all media, installed a PCI NIC, have changed the router three times. There are no errors in the DNS event logs pertaining to what's going on. We've also been on to BT who are adamant that it's not their end. Could someone shed some light on what could be going on or where else to look in the configuration of the server? Thank you.

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• Server 2008 email on Event variables

  - by Jeff Miles

  One of the new features of Server 2008 is the ability to attach a task to a specific event in the event logs. One of the actions available is to send an email through a SMTP server. This is working great, however it would be ideal if in the message body, the Event contents could be placed. I have tried using $eventdescription and %eventdescription%, but those are just shots in the dark. Any amount of googling produces no results. Does anyone know if this is possible? Update: Sparks' suggestion below is a step in the right direction I believe, however that method doesn't seem to work for all values. For example, I can pull the RecordID, Severity and Channel as shown, but I can't use the same method to retreive the EventID, or most importantly the description. Here's the raw XML from one event: [Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"] [System] [Provider Name="DFSR" /] [EventID Qualifiers="16384"]4412[/EventID] [Level]4[/Level] [Task]0[/Task] [Keywords]0x80000000000000[/Keywords] [TimeCreated SystemTime="2009-05-14T18:18:09.000Z" /] [EventRecordID]45692[/EventRecordID] [Channel]DFS Replication[/Channel] [Computer]servername.domain.com[/Computer] [Security /] [/System] [EventData] [Data]9046C3F4-843E-4A53-B941-4B20764072E5[/Data] [Data]D:\departments\Geomatics\Plan Quality\Data Processing\CG3533017 2009-05-13 KT FIXED[/Data] [Data]D:\departments[/Data] [Data]{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [Data]Departments[/Data] [Data]swg.ca\files\departments[/Data] [Data]B8242CE2-F5EB-47DA-BA5B-1DD2F7EE3AB9[/Data] [Data]DFAA7A54-66CB-4C31-81A0-0F861382C32C[/Data] [Data]CG3533017 2009-05-13-{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [/EventData] [/Event] I have tried using a ValueQuery for EventData, but it returns no data.

  Read the article

• CPU usage always below 10% in windows server 2008 r2 x64

  - by ???

  I am using a server with windows server 2008 r2 running on it to run my program. The CPU of the server is Intel xeon x5570 2.93GHz with 2 processors, 8 cores per processer. However, I found that the cpu usage is almost always below 10% even I use 32 threads in my program. And I also found that sometimes the cpu usage could reach as high as 93% through the task manager when running my program and at that moment my program has processed over 1000 files per second while normally, it only processed over 50 files per second. However, this does not happen often. I use tools downloaded from the internet to make sure no core sleeps when the server is on, nothing changed. Also, I edited the windows register to make sure that I, as an administer, have no cpu usage limit. But it changed nothing. Is there anyway that I can make full use of my cpu? That is to say that each core runs a thread of my program and the total cpu usage could reach over 50% when I use a reasonable number of threads in my program. Did this happen to anyone of you? And could you help me with this ? Thank you!

  Read the article

• Windows Server 2008 IIS7 - page requests randomly hang or timeout

  - by seb835

  I've just installed a fresh copy of Windows Server 2008 x64 with IIS7 and PHP (fast CGI). However, I'm noticing that after moving my web site from a similarly specified machine to this one, I'm getting issues. The issue seems to be that randomly, as I'm clicking through the web pages being served, the browser will suddenly hang saying "waiting for mysite.com...". Sometimes the page will then timeout, or finally resolve after 20 to 30 seconds, but maybe missing the CSS style sheet. Very strange, as this is the only website installed on this new server, and only myself using/testing it. Server is installed in the same data centre below the old server. Has anyone else had a similar problem? I tried increasing the max workers pool to 10 (from 1), but this has no effect. Seems to happen most frequently after 1 or 2 minutes of inactivity on the website, then trying to load/refresh a web page. Many thank for any info and help. Kind Regards, Seb

  Read the article

• Repair Windows 2008 boot

  - by aksamit

  I have been caught in a loop where I can't boot up Windows Server 2008. When the OS starts to boot I am presented two options: Launch Startup Repair (recommended) Start Windows Normally No matter what option is chosen I end up with a black screen stating "Windows is loading files..." which takes approx 15 minutes until "System Recovery" is started. I try to run the "Startup Repair" but it reports the following error: Problem Event Name: StartupRepairOffline Problem Signature 01: 0.0.0.0 Problem Signature 02: 0.0.0.0 Problem Signature 03: unknown OS Version: 6.1.7600.2.0.0.256.1 Locale ID: 1033 Actually no matter what other options I would try in the System Recovery they would also report some kind of error. Some other logging I have been able to extract: Diagnosis and repair details: Number of repair attempts: 1 Session details System Disk = Windows directory = AutoChk Run = 0 Number of root causes = 1 Test Performed: Name: System disk test Result: Completed successfully. Error code = 0x0 Root cause found: A hard disk could not be found. If a hard disk is installed, it is not responding. So it is actually stating that Harddisk could not be found... which to me seems to be a bit contradictious since the System Recovery just loaded all files from the hard disk it now states it cannot find. Any ideas on what other options I have?

  Read the article

• SBS 2008 Sharepoint Database good Memory Limit.

  - by ldelgado

  I manage a small network running on Small Business Server 2008. Lately, the Sharepoint embedded database is getting out of control with its memory usage. I've got a total of 16 GB of RAM on this server, and the Sharepoint database sometimes uses almost 8 GB of RAM. This never happened before, and it started happening after I installed Backup Exec 2010. It happens after a backup is performed. So I suspect there is a memory leak involved. I am working on that issue, but this question isn't about that. I would like to limit the amount of memory the Embedded database uses. I know how to do it. My question is, what would be the ideal amount of memory that I can allocate to Sharepoint? There are only 4 users on my network. One of the users uses two computers but not at the same time. They use sharepoint for a company calendar, and sometimes they share files that way also. Let me know if you need to know anything else. Thanks,

  Read the article

• Missing Memory on Windows Server 2008

  - by Chris Lively

  I have a windows 2008 x64 server with 8GB of RAM installed. Task Manager and Resource Monitor both insist that 7.5GB of the RAM is in use. However, the memory list under Processes (Memory Private Bytes) doesn't add up. I do have Show Processes from all users checked and hand adding the numbers I come up with about 3.5GB of RAM. I also looked at the latest copy of SysInternals Process Explorer. And neither the Private Bytes or Working Set adds up to more than about 3.5GB of RAM in use. What's going on? ===== Update: I bounced the server to see what would happen with the memory utilization. After boot and regular operations began it sat at 3GB of RAM usage. 18 hours later, it's back up to 6.8GB of usage with no indication as to where the additional 3.5GB or so of RAM is being used. Here are links to screen shots of the resource monitor and task manager: Resource Monitor Task Manager Update 2: Well, I believe I located the problem. When I detached one of the larger databases from my sql server the amount of ram shown as "in use" dropped drastically. The Memory Private Bytes count barely moved. So I'm guessing that SQL server has some way of allocating memory where it doesn't really show up in any of the monitors. I went further and created a new database file, then transferred all of the data from the one I detached. Even though it has the same data, and the same transactions going through it, the memory in use has stayed low. Maybe there was some corruption in the DB? I'll leave it to the DB gods and go searching for another "problem" ;)

  Read the article

• Windows Server 2008 R2 grinds to a screeching halt during file copy operations

  - by skolima

  When my Windows Server 2008 R2 machine is performing any large disk operations (copying 10GB files from one drive to another, copying similar file over network, merging HyperV snapshots, compressing large files), performance of the whole machine slows down terribly, everything becomes unresponsive. This is noticeable in any situation when the disk access is large enough not to fit in the cache. Are there any settings available for tuning this behaviour? I can accept slower file transfer if this would give me more responsiveness. System details: Dell Optiflex 960, Core 2 Quad Q9650, 8GB RAM, 2 SATA drives - 320GB (ST3320418AS) and 1TB (ST31000528AS), NCQ active on both, Intel 82564LM-3 Gigabit Ethernet, ATI HD 3450 graphics, Intel ICH10 bridge. We have multiple machines like this, every one is exhibiting the same behaviour. I though this was overkill for a workstation, apparently I was mistaken. Update: I guess I shouldn't have mentioned the HyperV at all. The above configuration is a standard workstation setup at the company I work for, this is not a server of any kind. I have at most 3 virtual machines working, and usually I'm the only person accessing them. Never the less, the slowdown occurs even when no VMs are running. On a Linux machine I'd simply ionice the copy process and I could forget about it, is there any way to manage IO priorities on Windows?

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >