Search Results

Search found 7728 results on 310 pages for 'wifi driver'.

Page 53/310 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• Airport Extreme and Windows PC via regular LAN (not WIFI)

  - by Mr AJL

  So I got an airpoort extreme, and everything works beautifully on the mac, but my windows 7 PC which is connected via a regular ethernet cable can't see any network. The Win7 PC says there's no cable connected. Any ideas? Is there some kind of setting you have to enable with the Airport utility? I looked everywhere but can't find anything. Thanks!

  Read the article

• broadcom 5722 NIC not installed on Ubuntu Server, although driver present

  - by Bastien

  Hello, I just installed Ubuntu Server 10.04 LTS, running kernel 2.6.32-24-server, on a brand new Dell T110 server, supposedly fully compatible with Ubuntu Server. I have two NICs: one ONBOARD, the other additional on PCI. both of them are Broadcom netXtreme 5572. on the first boot of the system, I could see both cards as eth0 and eth1 (with ifconfig) I configured eth0 as static IP (as planned), and did not configure eth1. after rebooting, one of the two NICs "disappeared": it does not appear in ifconfig at all. the one that disappeared is the ONBOARD one. I investigated a bit and found the following things: the card is SEEN, but not "installed", it appears as "UNCLAIMED" in lshw: *-network UNCLAIMED description: Ethernet controller product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress cap_list configuration: latency=0 resources: memory:df9f0000-df9fffff *-network description: Ethernet interface product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 00 serial: 00:10:18:60:23:64 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.102 duplex=full firmware=5722-v3.09 ip=10.129.167.25 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:35 memory:dfaf0000-dfafffff so I checked my dmesg and found a few strange lines, showing, there actually is a problem bringing up this card: [ 3.737506] tg3: Could not obtain valid ethernet address, aborting. [ 3.737527] tg3 0000:04:00.0: PCI INT A disabled [ 3.737535] tg3: probe of 0000:04:00.0 failed with error -22 [ 3.737553] alloc irq_desc for 17 on node -1 [ 3.737555] alloc kstat_irqs on node -1 [ 3.737560] tg3 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.737566] tg3 0000:05:00.0: setting latency timer to 64 [ 3.793529] eth0: Tigon3 [partno(BCM95722A2202G) rev a200] (PCI Express) MAC address 00:10:18:60:23:64 [ 3.793532] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 3.793534] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.793536] eth0: dma_rwctrl[76180000] dma_mask[64-bit] that actually shows that one NIC is recognized, the other is not. I researched a bit more, with lspci -v: 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: fast devsel, IRQ 16 Memory at df9f0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-00-00-fe-ff-00-00-00 Kernel modules: tg3 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: bus master, fast devsel, latency 0, IRQ 35 Memory at dfaf0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 64-23-60-fe-ff-18-10-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 here I could see that the MAC address is 00-00-00-FE-FF-00-00-00, which, according to some forum posts on several websites, could be an issue. I've researched everything I could on the net, and found out several people having slightly comparable issues, but they usually involve different HW, and do not provide a proper explanation / solution... I would appreciate if anyone around here has some info to share ! thanks

  Read the article

• Can't set-up Wifi Adhoc on my Raspberry Pi with an USB dongle

  - by Wouter

  I am trying to set-up an access point (ad-hoc) for my Raspberry Pi. That means I'm trying to "share" the ethernet connection over Wi-Fi. I am doing this using my Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter. When following a tutorial (or actually every tutorial), it immediately goes wrong. root@pinkypi:/home/pi# iwconfig wlan0 mode ad-hoc Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Device or resource busy. I already tried ifdown and not having it in the USB port at the startup. If it helps, every action with the thing fail (or at least setting the mode). I am using Debian. I'm sure I'm overseeing something, but I can't find out what. What is wrong?

  Read the article

• How to setup Dual Head with "radeon" driver for R770?

  - by user1709408

  I want to make dual head setup without xrandr but with Xinerama. I put "Screen 1" line into xorg.conf, but card still show identical output on DVI-2 and DVI-3 It is important to use xinerama for me (to glue three monitors), that's why i decide not to use ranrd (randr is incompatible with xinerama as i read somewhere) Here is my videocard (HD 4850 X2): lspci | grep R700 03:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] 04:00.0 Display controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] Here is how monitors are connected: grep "DVI" /var/log/Xorg.0.log [ 1210.002] (II) RADEON(0): Output DVI-0 using monitor section Monitor0 [ 1210.048] (II) RADEON(0): Output DVI-1 has no monitor section [ 1210.079] (II) RADEON(0): EDID for output DVI-0 [ 1210.080] (II) RADEON(0): Printing probed modes for output DVI-0 [ 1210.128] (II) RADEON(0): EDID for output DVI-1 [ 1210.128] (II) RADEON(0): Output DVI-0 connected [ 1210.128] (II) RADEON(0): Output DVI-1 disconnected [ 1210.128] (II) RADEON(0): Output DVI-0 using initial mode 1920x1200 [ 1210.160] (II) RADEON(1): Output DVI-2 using monitor section Monitor2 [ 1210.215] (II) RADEON(1): Output DVI-3 has no monitor section [ 1210.246] (II) RADEON(1): EDID for output DVI-2 [ 1210.247] (II) RADEON(1): Printing probed modes for output DVI-2 [ 1210.299] (II) RADEON(1): EDID for output DVI-3 [ 1210.300] (II) RADEON(1): Printing probed modes for output DVI-3 [ 1210.300] (II) RADEON(1): Output DVI-2 connected [ 1210.300] (II) RADEON(1): Output DVI-3 connected [ 1210.300] (II) RADEON(1): Output DVI-2 using initial mode 1920x1200 [ 1210.300] (II) RADEON(1): Output DVI-3 using initial mode 1920x1200 Here is my /etc/X11/xorg.conf Section "ServerFlags" Option "RandR" "0" Option "Xinerama" "1" EndSection Section "ServerLayout" Identifier "Three Head Layout" Screen "MyPrecious0" Screen "MyPrecious2" RightOf "MyPrecious0" Screen "MyPrecious3" LeftOf "MyPrecious0" EndSection Section "Screen" Identifier "MyPrecious0" Monitor "Monitor0" Device "Device300" EndSection Section "Screen" Identifier "MyPrecious2" Monitor "Monitor2" Device "Device400" EndSection Section "Screen" Identifier "MyPrecious3" Monitor "Monitor3" Device "Device401" EndSection Section "Device" Identifier "Device300" BusID "PCI:3:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device400" BusID "PCI:4:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device401" BusID "PCI:4:0:0" Screen 1 Driver "radeon" EndSection Section "Monitor" Identifier "Monitor0" EndSection Section "Monitor" Identifier "Monitor2" EndSection Section "Monitor" Identifier "Monitor3" EndSection I tried to switch to vesa driver (didn't work for me) I tried to add options like Option "ZaphodHeads" "DVI-2" and Option "ZaphodHeads" "DVI-3" into sections "Device 400" and "Device 401" (this didn't help because "ZaphodHeads" option is for ranrd, and randr is disabled by decision) I tried to merge sections "Device 400" and "Device 401" into one section and add Option "ZaphodHeads" "DVI-2,DVI-3" (see comment about randr above) single section setup helps to change log line RADEON(1): Output DVI-3 has no monitor section into RADEON(1): Output DVI-3 using monitor section Monitor3 but nothing was enough to switch from screen cloning to separate screens. This problem (lack of documentation on radeon driver) is similar to these: Radeon display driver clones monitors while using Xinerama (moderators decision to close that problem was wrong) Ubuntu 12.10 multi-monitor setup isn't working The problem is solvable, because this hardware worked as three headed for me earlier with gentoo/xorg-server-1.3 Xorg -configure creates setup for the first monitor on the first GPU Please don't advise to use fglrx/aticonfig/amdcccle (this goes against my religion beliefs)

  Read the article

• Forcing logon to Air Watch server upon joining wifi

  - by DKNUCKLES

  I'm setting up a wireless controller that I would like to leave as unsecured. When a user connects to this network they need to be forwarded to a specific page where they can authenticate with the Air Watch system they have in place. Once authentication takes place, a profile will be downloaded to their device and we can administer the devices accordingly. I'm mulling over how I can force the page to the user when they log in. The methodology I'm thinking about working with is creating a NAT rule for that VSC that would forward all port 80 and 443 traffic to the airwatch server. Once they authenticate, a profile will be downloaded which will connect the devices to an Virtual Access Point who's SSID isn't broadcasted. Is this methodology correct or can someone think of an easier / more efficient way of accomplishing this? The controller is an HP MSM720 for what it's worth.

  Read the article

• Streaming Netflix through Wifi kills all other devices

  - by maleki

  I have a "Belkin N150" Router. My current setup is wired connection to my personal tv and xbox with wireless going to the Wii and Bedroom laptop. Anytime I try streaming Netflix Instant Queue on the Wii, every other device has problems. The Wii works fine but everything else's connection is destroyed. Streaming through the Xbox doesn't create any issues for other devices. What kind of issue is occurring and how can I fix it?

  Read the article

• How to check wifi networking standard of current connection

  - by yzfr1

  Both my router and my wireless networking card support the standards 802.11a/b/g/n but as I'm only getting speeds around 30-40 Mbit/s I suspect that it's the g standard being used instead of n. Now, I'd like to verify this somehow, so my question is: Is there a way (like a network diagnistics tool or the like) to find out which standard is currently used in the communication between computer and router?

  Read the article

• Installing ethernet drivers with no install package

  - by Josh

  I recently got my new Sony Vaio laptop and formatted it into Windows 7 Ultimate. I would like to use the Windows Easy Transfer Tool over a network connection to transfer some of my files over from my desktop PC. Before I do this though, I need to install the ethernet LAN drivers (I'm currently using the built in Wifi). I downloaded the original LAN driver that came with my Vaio originally from the Sony website: http://support.vaio.sony.eu/computing/vaio/downloads/preinstalled/index.aspx?l=en_GB&m=VPCEB1Z0E_B [Scroll down to the 450KB Ethernet driver] When I unzip the package, these files are inside: yk62x64.cat yk62x64.dll yk62x64.inf yk62x64.sys As you can see, no installer. Can anyone guide me through how to properly install these drivers? I have thought of using Google but I'm clueless as to what query to use. Thanks.

  Read the article

• My NetGear router suddenly started showing limited access for all wifi connected laptops

  - by Yasser

  I have netgear n300 router which I had installed about 6 months back. Here is how the setup is, I have a local internet provider by the name of "Hathway" they have this modem which is in turn connected to the router and a wire from router is connected to my desktop. As shown in this pic below, except for the laptop I use a desktop rest all the connection is same So with this connection and the below configuration, every thing worked fine. The desktop would work also all my laptops and mobile devices would connect and be able to access the internet without any problem. Now suddenly since yesterday (with no changes made whatsoever to this config) all my laptops start showing the limited connection message and cannot connect to the internet. However the desktop which is connected can access the internet. Can someone please guide me on this.

  Read the article

• Encrypt LAN and wifi traffic on small private network

  - by Grimlockz

  I need some advice about encrypt all traffic on a small private network running wi-fi and LAN traffic on 192.168.0.x network. The network would comprise of client laptops connecting to the wi-fi router (192.168.0.254) via ethernet connection or wireless. The main purpose of the server is for the client laptops to talk to two servers on different IP's (192.168.0.200 and 192.168.0.201) on ports 80 and 433. My main concern is having packet sniffers and what not getting access to the data. The only ways I see at the moment is to have VPN running on the network or use IPSec policy's to do this. Any other ways guys?

  Read the article

• Updated 11.10 - now trackpad and wifi won't work. How can these be fixed?

  - by Aron Standley

  I reinstalled 11.10 on my Asus EEE 1005HA, and my mousepad hasn't been working since. I've tried the workarounds mentioned in this post: http://ubuntuforums.org/showthread.php?t=1867357 but, I get the message on the command line that says, "Synaptic isn't installed." When I go to the network settings to install Synaptic, I can't turn on wifi - no wireless options exist. How can I turn on wifi from the command line, on a new 11.10 install? Or, is there a way to turn on the trackpad and wifi from the install thumb drive? How can I move forward?

  Read the article

• IP Address on internet access shared over ad-hoc wifi network

  - by Jacxel

  The Situation When im staying at my girlfriends we both like to have internet access on our laptops but her accommodation don't allow wireless routers. My Question My question is if I set up an Ad-Hoc network to share the internet connection as shown here on How To Geek. Will my laptop be acting as a wireless router or will the connection all go through my laptop as one ip address so it appears to be my computer accessing the webpages etc, that my girlfriend actually is. i would be interested in knowing any additional information that could help sove this problem eg. if connectify would do what i want.

  Read the article

• Sharing a wifi connection between different user profiles on Windows XP

  - by crowne

  I've set-up two separate user profiles on an old laptop running Windows-XP, and noted the following strange behaviour. When the wireless network is setup using WEP both user profiles can connect to the internet and I can switch between user profiles, without network connectivity issues. However when I changed the wireless security to WPA2, the first user to connect gets access to the internet, when switching to the second profile the connection fails. The behaviour is the same regardless of which of the two profiles logs on first. I also tried this with one user with admin rights and one without, and got the same result. I'm not too concerned about a fix for this other than forcing the users to log-off when sharing the laptop, but I'd be interested to know if anyone can corroborate my findings. The network config was done using Intel® PROSet/Wireless.

  Read the article

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  Hello - I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified with SpeakEasy and Speedtest.net) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• 12.04 making BCM4313 card work with aircrack-ng?

  - by Charles Forest

  I'm a real Linux Noob, just started using it (this month) and until now i had no issues. now i'm trying to set-up aircrack-ng on my laptop, but it seems like it's using the worst card possible (or almost) there is a TON of tutorial on this card (seems to be hell to set-up) i have tryed some, but i ended up uninstalling my drivers, messing with my desktops, and ended by having no more "X" to close my windows (i have no clue how i ended there) i just re-installed my linux (took me 2 hours to setup everything again), but now i'm a bit "Scared" to try tutorials randomly again. Right now it says the driver is wl, wich is not the one i want (AFAIK it's not supported) i'm not sure what kind of informations are needed, but here's what i think could be usefull. lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: agpgart-intel 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel modules: i2c-i801 01:00.0 3D controller [0302]: NVIDIA Corporation GF108 [GeForce GT 540M] [10de:0df4] (rev a1) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb WIRELESS CARD 02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac REST... 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: r8169 Kernel modules: r8169 04:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: xhci_hcd Also, if i'm "screwed" with my hardware, just tell me.

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the internet via Eth0. Has one wireless network adapter and one more ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the Internet via Eth0. Has one wireless network adapter and one another ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration.

  Read the article

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• Laptop's wifi router is not emitting signals therefore my PC and Nokia cell are not connecting to internet

  - by umer sanny

  I have a USB internet connection which I plugged into my laptop. I converted my laptop's Wifi into a Wifi router so that I can attach my PC and cell to this network and enjoy internet, but it doesn't work. I have a Dell Inspiron N5110 i7 Windows 7 64-bit laptop, Dell D865 PC and Nokia C5. My PC and cell are showing that there is a new Wifi connection available, but when I connect to it, it won't load any web page. Reason is my laptop's Wifi is not emitting any internet signals or may be some other issue which i dont know.. laptop's adapter is 802.11b/g/n I don't know why. How can I enjoy Wifi internet on laptop, PC and cell at the same time?

  Read the article

• How can I install ATI Catalyst Video driver of Ubuntu 12.04.3?

  - by Eastsun

  EDIT My computer is Thinkpad E420 with Intel HD3000 and ATI 6630m. I have reinstalled my Ubuntu12.04.3 yesterday. I had successfully installed Ubuntu and ATI Catalyst Video driver many times about half year ago following these links: How do I get AMD/Intel Hybrid Graphics drivers to work? What is the correct way to install ATI Catalyst Video Drivers (fglrx)? However, this time I have no luck with installing ATI Catalyst Video driver. I have tried version 13.4, 13.1, 12.8 of ATI Catalyst Video driver. It seemed that 13.4 doesn't support 12.04 any more, following this link , the lowest Ubuntu version supported by ATI 13.4 is 12.10 and for the reset of the ATI drivers, the kernel version and xorg version of Ubuntu 12.04.3 is too high to be supported. So, should I stay on ubuntu 12.04.1 with ATI 12.8, or there is any way to install ATI driver on Ubuntu 12.04.3?

  Read the article

• Is it possible to get xRandR to see two separate outputs with the nvidia driver?

  - by rumtscho

  I have two monitors, which I have set up with nvidia-settings in Twinview. The result: When I want to do something in xRandR, it does not function. It doesn't report one output per video card head, but a single output mapped to the combined area of both monitors: rumtscho@bradbury:~$ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 3840 x 1440, current 3840 x 1440, maximum 3840 x 1440 default connected 3840x1440+0+0 0mm x 0mm 3840x1440 50.0* Now I promised somebody to help test a driver. The developer is using an open source driver for Intel video cards, and his driver assumes that there is more than one xRandR output, each mapped to a monitor. So I tried rewriting my xorg.conf to somehow get two outputs to show up, but failed. Googling showed that people faced with the xRandR-nvidia problem either stopped using xRandR and achieved what they needed with nvidia-settings, or changed their driver to nouveau. The first is not going to help in my situation, and I am not willing to give up the proprietary driver, because Compiz won't work without it. So does anybody know a way to get nvidia to actually pass on information on outputs to xRandR?

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Using a second wifi router as a wireless bridge

  - by Greg-J

  I purchased a D-Link DGL-4500 to replace my aging WRT54G around a year ago, only to find it nowhere near as reliable. It's been collecting dust since. I'm wondering if there is a way to use it as a wireless bridge so I can connect it to my home network and then use it's ethernet ports to provide network access to several devices. Is this something that can be done? If not, are there devices meant for this? Any help would be appreciated.

  Read the article

• Which nvidia driver from additional drivers option should I choose?

  - by sud_the_devil

  I have NVIDIA Geforece 7025 / nForce 630a integrated gfx card on my UBUNTU 12.04.And I have 4 options in Additional drivers: NVIDIA accelerated graphics driver (version 173) NVIDIA accelerated graphics driver (post-release updates)(version current updates) NVIDIA accelerated graphics driver (version current)[Recommended] NVIDIA accelerated graphics driver (post-release updates)(version 173 updates) I am currently using the First option. My Problem is there I can't update the version 173 to the latest version of drivers using xswat PPA. Whenever I do it and reboot but the NVIDIA xserver sttings always shows me the same version. Which option would allow me to update my drivers to the current version?

  Read the article

• Is there a NVIDIA driver (for a 7-series card) that will actually work for 12.10?

  - by DS13

  I see many similar topics on this, but I've tried all their suggestions, and nothing has worked. ISSUE: I do a clean install of Ubuntu 12.10. Boots fine with the “nouveau” graphics driver – graphics are very slow and choppy. The three other driver options in Ubuntu (official NVIDIA drivers), all result in a variation of the black screen on boot up. There will be NO access to a command line/GUI in anyway what-so-ever (tried every option recommended out there, but the system is unusable at this stage). I can only reinstall, and try different drivers…and I only ever get one shot at it. QUESTIONS: Does anyone know of a NVIDIA driver that will actually work with a Nvidia GeForce 7350LE? Or a 7-series card in general? This is my second computer, and I’m just trying to get a working install of Ubuntu on it. I don’t want to put much money into it, as I have seen Ubuntu run great on much older/less capable machines. I’ve got a decent Intel processor (2.3Ghz), 2GB of RAM, 320GB hard drive, 32-bit architecture, and there is no other O/S installed. It appears as if the graphics card is holding me back. Should I just buy a cheap graphics card (non-NVIDIA) to put in as a replacement? TRIED SO FAR: -all drivers available in Ubuntu *all fail -manual install of some different NVIDIA drivers *all fail -also tried installing the generic kernel, Nvidia driver doesn't work in 12.10 *no difference -every method suggested to at least get a command line after switching to a NVIDIA driver *all fail

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >