Search Results

Search found 13862 results on 555 pages for 'questions'.

Page 530/555 | < Previous Page | 526 527 528 529 530 531 532 533 534 535 536 537  | Next Page >

  • KVM with one host IP and a different subnet for machines

    - by Jguy
    I've already setup a KVM host with proper IP configurations, but my host had me create DHCP and use that to assign the IP's to the machines. I want to see if there's an easier way to do it (or better). Upon my first setting out on this, I didn't find anything that pointed me in the right direction. I'm coming off a fresh install of Debian 6.0 x64, so I have nothing installed. I've logged in, queried for the below information and changed the password from my host set one. I have a Debian 6.0 x64 system with the following initial network configuration (substituted 255 in place of my real first octave): # tail /etc/network/interfaces auto eth0 iface eth0 inet static address 255.9.24.80 broadcast 255.9.24.95 netmask 255.255.255.224 gateway 255.9.24.65 # default route to access subnet up route add -net 255.9.24.64 netmask 255.255.255.224 gw 255.9.24.65 eth0 I have a /29 subnet that I want the virtual machines to use from my host: IP: 255.46.187.152 /29 Mask: 255.255.255.248 Broadcast: 255.46.187.159 Usable IP addresses: 255.46.187.153 to 255.46.187.158 I like the interface of Cloudmin, so I want to try and use that if I can to administrate my guests. So, my questions: How do I set this up on the host system the best so that I can use the additional Subnet IP's on the guests and have them accessible from the internet? I also need to host a DNS server, which means one of these VM's has to have two IP's assigned to it and accessable from the outside world. How can I do that using Cloudmin? I had a question about this here: Multiple IP addresses assigned to one KVM VM But I just reformatted the entire server and am trying to figure out a better way of doing this. Machine information: # ip route show 255.9.24.64/27 via 255.9.24.65 dev eth0 255.9.24.64/27 dev eth0 proto kernel scope link src 255.9.24.80 default via 255.9.24.65 dev eth0 brctl is empty # ip addr list 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether c8:60:00:54:b5:d8 brd ff:ff:ff:ff:ff:ff inet 255.9.24.80/27 brd 255.9.24.95 scope global eth0 inet6 fe80::ca60:ff:fe54:b5d8/64 scope link valid_lft forever preferred_lft forever Thank you for any help you can provide me. EDIT: I've installed kvm and cloudmin: aptitude install qemu-kvm libvirt-bin wget http://cloudmin.virtualmin.com/gpl/scripts/cloudmin-kvm-debian-install.sh ./cloudmin-kvm-debian-install.sh Rebooted and now my network configuration looks like this: # device: eth0 iface eth0 inet manual # default route to access subnet iface br0 inet static address 255.9.24.80 netmask 255.255.255.224 broadcast 255.9.24.95 network 255.9.24.64 bridge_ports eth0 gateway 255.9.24.65 I setup in Cloudmin the Start IP as 255.46.187.153 and End IP as 255.46.187.158. The CIDR is 29 and the gateway is 255.46.187.152. I've installed a guest with ubuntuserver 12.04 x64, which was able to get and retrieve internet resources during installation, but now cannot reach anything nor can it be reached from anything. Its network configuration is: iface eth0 inet static address 255.46.187.153 netmask 255.255.255.224 broadcast 255.46.187.159 gateway 255.46.187.152 dns-nameservers <host provided nameservers> And is not able to ping google.com through DNS or direct IP, I can't ping the VM from the outside or the host. any ideas now?

    Read the article

  • A failed disk (Pay for professional service or SpinRite?)(new edit)

    - by huggie
    EDIT: After much negotiating and begging and seeing through promotion smoke screen, thanks to the nice representative who took my case, I now know that the engineer has already fixed my NTFS partition (I guess it might be a bad block in the partition table?). She told me that the problem was considered minor, and I should be able to boot normally and just copy stuff out. Whew..I'm glad I didn't agree to the NTD $16,000 deal. New question (should this be in a new thread?): is it safer to use the linux "dd" command or is it better to boot normally into Windows XP and just copy stuff out? EDIT2: Thanks to all the help. I give the best answer to Console as it's most directed related to my question. But many suggestion are helpful and informational. ---- ORIGINAL POST BELOW --- Hi, in my previous post (You don't need to read but it's at http://superuser.com/questions/48838/windows-xp-a-disk-read-error-occurred), I said that my hard disk was not booting and is showing "a disk read error occurred". I took it to a recovery professional. A representative responded today told me that the NTFS partitions have a "NTFS partition system crash". I have no idea what that means. The engineer handling my drive will not be available for contact till tomorrow. Now the company charges me NTD (New Taiwan Dollar) $16,000 to recover lost data, that's kind of a lot considering that my graduate student monthly stipend is currently NTD $32,000 (max. allowed by regulation, may be lower, may change depend on funding). Now I'm weighting in between the options. Option A: let the professional recovers it with the half of my monthly stipend. If file/directories I designated are not recovered I don't pay a penny. (other than the initial examination fee of NTD $1000 which I've already paid.) Option B: let me try SpinRite, if failed, back to Option A. I spoke to the representative at the company they recommended me not to handle it on my own (yeah of course that's what they all want to say, right?), and at the price tag the disk error is probably relatively minor and data recoverable. But the representative really did not have detailed information of the disk failure so I didn't take her recommendation readily. Though one thing I heed was that she said that what they would do is to duplicate the disk before attempting discovery, so there would be no data loss (Is this true? can't duplicating invoke further data loss?). That sounds very good to me. Or maybe a third option: Option C: Negotiate with them to pay them to duplicate the disk hopefully for a much smaller price tag. Let me try SpinRite, if failed, back to Option A. This is a difficult decision. Ultimately I want my data back, but if a cheaper way is available to achieve the same thing... Can operating with SpinRite also corrupt data in someway? I've no idea what happened to my drive. I'll attempt to contact the engineer and hope to get it clarified and make an edit here.

    Read the article

  • Why am I unable to telnet to a local port that has a listening service?

    - by Skip Huffman
    I suspect this is either a very simple question, or a very complex one. I have a headless server running ubuntu 10.04 that I can ssh into. I have full root access to the system. I am trying to set up an ssh tunnel to allow me to vnc to the system (but that isn't my question. I have vnc running on port 5903, here is the netstat output for that: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:5903 0.0.0.0:* LISTEN 7173/Xtightvnc tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 465/sshd But when I try to telnet to that port, from within the same system and login, I get unable to connect errors # telnet localhost 5903 Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection timed out I am able to telnet to port 22 (as a verification) ~# telnet localhost 22 Trying ::1... Connected to localhost. Escape character is '^]'. SSH-2.0-OpenSSH_5.3p1 Debian-3ubuntu7 I have tried to open up any possible ports using ufw (probably clumsy fashion) # ufw status numbered Status: active To Action From -- ------ ---- [ 1] 5903 ALLOW IN Anywhere [ 2] 22 ALLOW IN Anywhere What else might be blocking this connection locally? Thank you, Edit: The only reference to port 5903 in iptable -L -n is this: Chain ufw-user-input (1 references) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:5903 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:5903 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:22 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:8080 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:8080 I can post the whole output if that will be useful. hosts.allow and hosts.deny both contain only comments. Re-Edit: Some other questions pointed me to nmap, so I ran a portscan through that utility: # nmap -v -sT localhost -p1-65535 Starting Nmap 5.00 ( http://nmap.org ) at 2011-11-09 09:58 PST NSE: Loaded 0 scripts for scanning. Warning: Hostname localhost resolves to 2 IPs. Using 127.0.0.1. Initiating Connect Scan at 09:58 Scanning localhost (127.0.0.1) [65535 ports] Discovered open port 22/tcp on 127.0.0.1 Connect Scan Timing: About 18.56% done; ETC: 10:01 (0:02:16 remaining) Connect Scan Timing: About 44.35% done; ETC: 10:00 (0:01:17 remaining) Completed Connect Scan at 10:00, 112.36s elapsed (65535 total ports) Host localhost (127.0.0.1) is up (0.00s latency). Interesting ports on localhost (127.0.0.1): Not shown: 65533 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 112.43 seconds Raw packets sent: 0 (0B) | Rcvd: 0 (0B) I think this shows that 5903 is blocked somehow. Which I pretty much knew. The question remains what is blocking it and how to modify. Re-re-edit: To check Paul Lathrop's suggested answer, I first verified my ip address with ifconfig: eth0 Link encap:Ethernet HWaddr 02:16:3e:42:28:8f inet addr:10.0.10.3 Bcast:10.0.10.255 Mask:255.255.255.0 Then tried to telnet to 5903 from that address: # telnet 10.0.10.3 5903 Trying 10.0.10.3... telnet: Unable to connect to remote host: Connection timed out No luck. Re-re-re-re-edit: Ok, I think I have isolated it a bit to vncserver, not the firewall, darn it. I shut off vncserver and had netcat listen on port 5903. My vnc client then was able to establish a connnection and sit and wait for a response. Looks like I should be chasing a vnc problem. At least that is progress Thanks for the help

    Read the article

  • SQL Server Log File Won't Shrink due cause "log are pending replication" on non replicated DB?

    - by user796466
    I have a non Mission Critial DB 9am-5pm SQL Server database that I have set up to do nightly full backups and log backups every 30 minutes during business hours. The database is in full recovery and normally I have no reason to truncate/shrink logs unless I do some heavy maintenance. Log backups manage the size with no issue. However I have not been at this client for several weeks and upon inspection I noticed that the log had grown to about 10 times the size of the .mdf file. I poked around backups had been running and I had not gotten any severity error alerts (SQL mail). I attempted to put DB in simple recovery and shrink the log, this was no good. I precede to try a log backup and I got: The log was not truncated because records at the beginning of the log are pending replication or Change Data Capture. Ensure the Log Reader Agent or capture job is running or use sp_repldone to mark transactions as distributed or captured. Restart SQL Server rinse repeat same thing ... I said ??? Replication is not nor ever has been set up on this DB or database /server ??? So the log backups have not been flushing the .ldf. So I did a couple hours of research and I found: http://www.sqlmonster.com/Uwe/Forum.aspx/sql-server/5445/Log-file-is-not-truncated-inspite-of-regular-log-backup http://www.eggheadcafe.com/software/aspnet/30708322/the-log-was-not-truncated-because-records-at-the-beginning-of-the-log-are-pending-replication.aspx seems to be some kind of poorly documented bug ?? The solution seems to have been to run exec sp_repldone, more precisley EXEC sp_repldone @xactid = NULL, @xact_segno = NULL, @numtrans = 0, @time= 0, @reset = 1 This procedure can be used in emergency situations to allow truncation of the transaction log when transactions pending replication are present. Using this procedure prevents Microsoft SQL Server 2000 from replicating the database until the database is unpublished and republished. ~ MSDN When I do that I get the following Msg 18757, Level 16, State 1, Procedure sp_repldone, Line 1 Unable to execute procedure. The database is not published. Execute the procedure in a database that is published for replication. Which makes sense Because the DB has never been published for replication. I have several questions: A) First and foremost is, WTF is going on ? What is causeing this, I am interested in knowing the why here ? Is this genuinley a bug or is there some aspect of the backup that is not functioning properly that cause's the DB to mimick a replicated state ? Someone please edify me on this. B) Second ... Do I really have to publish / replicate this DB to exec this SP to fix this ??? Sounds crazy or is there some T-SQL that I can put it in a published state exec the proc and be on my way ... C) Third, if I do indeed have to publish this database to exec the SP to release this unneeded mis replicated/intended log , to get my .ldf file and backup back on track. How do I publish the database without an online host that it is asking for ??? I don't generally do this kind of database administration and need some guidance. Sorry if this is too verbose but just voicing the question helps me clarify it ... Thank you in advance for your help

    Read the article

  • How do I connect my Windows XP laptop to the internet?

    - by rubysiddhi
    Hello fellow super users, The Past I have a Acer Travelmate 2300 laptop running Windows XP. 6 months ago I moved into a new apartment and got a new internet connection set up. After getting an internet connection installed in my apartment I reinstalled Windows XP and at the same time wiped my drive clean losing all the original Acer software and drivers. Once XP was reinstalled I had to find all the drivers again to get the Travelmate laptop connected to the internet. So, using my Vista laptop which was connected fine, I went to the Acer Travelmate Series drivers download page to download the necessary drivers. I transferred them to my Acer XP machine and installed them the best I could (there were no easy instructions so I just had to find all the executables and run them). I eventually got connected to the internet but not exactly in the way I had hoped for. The Present To be connected to the internet I need to have an Ethernet cord connecting my computer (via the Ethernet port) to my router. This is a problem since it defeats the purpose of having a Wireless LAN card in my Acer laptop. One of the programs I downloaded from the Acer Travelmate Series page was the Acer Wireless LAN Configuration Utility. This program allows me to see the current network I am connected to and all the available networks I could potentially connect to. It reminds me of XP's Wireless Network Connection window/utility where you can see all available wireless networks, refresh the network list and connect to one of the networks. I should mention that my ISP set up a security enabled wireless network with WPA. This network requires a network key if you want to connect to it. I guess my Vista computer has the network key entered into it already. The problem is that I do not know what the network key is. Now obviously you would say just contact my ISP to get the key. And I will but there is just one extra weird issue. I am able to connect to another unsecured wireless network in the Wireless Network Connection window/utility. I can be on it as long as my Ethernet cable is plugged in. So this is not really wireless is it? And this indicates that even if I do get that network key password from my ISP, I will only solve one of the two problems I have. I will only solve being able to get online as long as I am connected to my router via the Ethernet cable. The Main Questions So how do I enable my acer IPN2220 Wireless LAN Card so that I can use my Acer laptop from anywhere with in my apartment? Or should I first get the network key from my ISP to access my security enabled wireless network? And then deal with getting the acer IPN2220 Wireless LAN Card working? Hard & Learned VS Easy & Stupid Of course contacting the ISP would be easier. Have em just come in here and do there thing. The problem with that is that they do not speak English (yeah, im in Poland) and it'd be a hell of a time trying to understand what they are doing (uncomfortable looking over their shoulder). Also, I want to learn how to do this task myself so that I can fix the problem if it ever happens again. You know, be more self sufficient. I look forward to helpful replies. Thanks, Xaviour

    Read the article

  • Multi-tenant ASP.NET MVC – Introduction

    - by zowens
    I’ve read a few different blogs that talk about multi-tenancy and how to resolve some of the issues surrounding multi-tenancy. What I’ve come to realize is that these implementations overcomplicate the issues and give only a muddy implementation! I’ve seen some really illogical code out there. I have recently been building a multi-tenancy framework for internal use at eagleenvision.net. Through this process, I’ve realized a few different techniques to make building multi-tenant applications actually quite easy. I will be posting a few different entries over the issue and my personal implementation. In this first post, I will discuss what multi-tenancy means and how my implementation will be structured.   So what’s the problem? Here’s the deal. Multi-tenancy is basically a technique of code-reuse of web application code. A multi-tenant application is an application that runs a single instance for multiple clients. Here the “client” is different URL bindings on IIS using ASP.NET MVC. The problem with different instances of the, essentially, same application is that you have to spin up different instances of ASP.NET. As the number of running instances of ASP.NET grows, so does the memory footprint of IIS. Stack Exchange shifted its architecture to multi-tenancy March. As the blog post explains, multi-tenancy saves cost in terms of memory utilization and physical disc storage. If you use the same code base for many applications, multi-tenancy just makes sense. You’ll reduce the amount of work it takes to synchronize the site implementations and you’ll thank your lucky stars later for choosing to use one application for multiple sites. Multi-tenancy allows the freedom of extensibility while relying on some pre-built code.   You’d think this would be simple. I have actually seen a real lack of reference material on the subject in terms of ASP.NET MVC. This is somewhat surprising given the number of users of ASP.NET MVC. However, I will certainly fill the void ;). Implementing a multi-tenant application takes a little thinking. It’s not straight-forward because the possibilities of implementation are endless. I have yet to see a great implementation of a multi-tenant MVC application. The only one that comes close to what I have in mind is Rob Ashton’s implementation (all the entries are listed on this page). There’s some really nasty code in there… something I’d really like to avoid. He has also written a library (MvcEx) that attempts to aid multi-tenant development. This code is even worse, in my honest opinion. Once I start seeing Reflection.Emit, I have to assume the worst :) In all seriousness, if his implementation makes sense to you, use it! It’s a fine implementation that should be given a look. At least look at the code. I will reference MvcEx going forward as a comparison to my implementation. I will explain why my approach differs from MvcEx and how it is better or worse (hopefully better).   Core Goals of my Multi-Tenant Implementation The first, and foremost, goal is to use Inversion of Control containers to my advantage. As you will see throughout this series, I pass around containers quite frequently and rely on their use heavily. I will be using StructureMap in my implementation. However, you could probably use your favorite IoC tool instead. <RANT> However, please don’t be stupid and abstract your IoC tool. Each IoC is powerful and by abstracting the capabilities, you’re doing yourself a real disservice. Who in the world swaps out IoC tools…? No one!</RANT> (It had to be said.) I will outline some of the goodness of StructureMap as we go along. This is really an invaluable tool in my tool belt and simple to use in my multi-tenant implementation. The second core goal is to represent a tenant as easily as possible. Just as a dependency container will be a first-class citizen, so will a tenant. This allows us to easily extend and use tenants. This will also allow different ways of “plugging in” tenants into your application. In my implementation, there will be a single dependency container for a single tenant. This will enable isolation of the dependencies of the tenant. The third goal is to use composition as a means to delegate “core” functions out to the tenant. More on this later.   Features In MvcExt, “Modules” are a code element of the infrastructure. I have simplified this concept and have named this “Features”. A feature is a simple element of an application. Controllers can be specified to have a feature and actions can have “sub features”. Each tenant can select features it needs and the other features will be hidden to the tenant’s users. My implementation doesn’t require something to be a feature. A controller can be common to all tenants. For example, (as you will see) I have a “Content” controller that will return the CSS, Javascript and Images for a tenant. This is common logic to all tenants and shouldn’t be hidden or considered a “feature”; Content is a core component.   Up next My next post will be all about the code. I will reveal some of the foundation to the way I do multi-tenancy. I will have posts dedicated to Foundation, Controllers, Views, Caching, Content and how to setup the tenants. Each post will be in-depth about the issues and implementation details, while adhering to my core goals outlined in this post. As always, comment with questions of DM me on twitter or send me an email.

    Read the article

  • Ajax Control Toolkit July 2011 Release and the New HTML Editor Extender

    - by Stephen Walther
    I’m happy to announce the July 2011 release of the Ajax Control Toolkit which includes important bug fixes and a completely new HTML Editor Extender control. You can download the July 2011 Release by visiting the Ajax Control Toolkit CodePlex site at: http://AjaxControlToolkit.CodePlex.com Using the New HTML Editor Extender Control You can use the new HTML Editor Extender to extend any standard ASP.NET TextBox control so that it supports rich formatting such as bold, italics, bulleted lists, numbered lists, typefaces and different foreground and background colors. The following code illustrates how you can extend a standard ASP.NET TextBox control with the HtmlEditorExtender: <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="Simple.aspx.cs" Inherits="WebApplication1.Simple" %> <%@ Register TagPrefix="asp" Namespace="AjaxControlToolkit" Assembly="AjaxControlToolkit" %> <html xmlns="http://www.w3.org/1999/xhtml"> <head runat="server"> <title>Simple</title> </head> <body> <form id="form1" runat="server"> <asp:ToolkitScriptManager runat="Server" /> <asp:TextBox ID="txtComments" TextMode="MultiLine" Columns="60" Rows="8" runat="server" /> <asp:HtmlEditorExtender TargetControlID="txtComments" runat="server" /> </form> </body> </html> This page has the following three controls: ToolkitScriptManager – The ToolkitScriptManager renders all of the scripts required by the Ajax Control Toolkit. TextBox – The TextBox control is a standard ASP.NET TextBox which is set to display multiple lines (a TextArea instead of an Input element). HtmlEditorExtender – The HtmlEditorExtender is set to extend the TextBox control. You can use the standard TextBox Text property to read the rich text entered into the TextBox control on the server. Lightweight and HTML5 The HTML Editor Extender works on all modern browsers including the most recent versions of Mozilla Firefox (Firefox 5), Google Chrome (Chrome 12), and Apple Safari (Safari 5). Furthermore, the HTML Editor Extender is compatible with Microsoft Internet Explorer 6 and newer. The HTML Editor Extender is very lightweight. It takes advantage of the HTML5 ContentEditable attribute so it does not require an iframe or complex browser workarounds. If you select View Source in your browser while using the HTML Editor Extender, we hope that you will be pleasantly surprised by how little markup and script is generated by the HTML Editor Extender. Customizable Toolbar Buttons Depending on the web application that you are building, you will want to display different toolbar buttons with the HTML Editor Extender. One of the design goals of the HTML Editor Extender was to make it very easy for you to customize the toolbar buttons. Imagine, for example, that you want to use the HTML Editor Extender when accepting comments on blog posts. In that case, you might want to restrict the type of formatting that a user can display. You might want to enable a user to format text as bold or italic but you do not want the user to make any other formatting changes. The following page illustrates how you can customize the HTML Editor Extender toolbar: <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="CustomToolbar.aspx.cs" Inherits="WebApplication1.CustomToolbar" %> <%@ Register TagPrefix="asp" Namespace="AjaxControlToolkit" Assembly="AjaxControlToolkit" %> <html> <head runat="server"> <title>Custom Toolbar</title> </head> <body> <form id="form1" runat="server"> <asp:ToolkitScriptManager Runat="server" /> <asp:TextBox ID="txtComments" TextMode="MultiLine" Columns="50" Rows="10" Text="Hello <b>world!</b>" Runat="server" /> <asp:HtmlEditorExtender TargetControlID="txtComments" runat="server"> <Toolbar> <asp:Bold /> <asp:Italic /> </Toolbar> </asp:HtmlEditorExtender> </form> </body> </html> Notice that the HTML Editor Extender in the page above has a Toolbar subtag. You can list the toolbar buttons which you want to appear within the subtag. In the case above, only Bold and Italic buttons are displayed. Here is a complete list of the Toolbar buttons currently supported by the HTML Editor Extender: Undo Redo Bold Italic Underline StrikeThrough Subscript Superscript JustifyLeft JustifyCenter JustifyRight JustifyFull InsertOrderedList InsertUnorderedList CreateLink UnLink RemoveFormat SelectAll UnSelect Delete Cut Copy Paste BackgroundColorSelector ForeColorSelector FontNameSelector FontSizeSelector Indent Outdent InsertHorizontalRule HorizontalSeparator Of course the HTML Editor Extender was designed to be extensible. You can create your own buttons and add them to the control. Compatible with the AntiXSS Library When using the HTML Editor Extender on a public facing website, we strongly recommend that you use the HTML Editor Extender with the AntiXSS Library. If you allow users to submit arbitrary HTML, and you don’t take any action to strip out malicious markup, then you are opening your website to Cross-Site Scripting Attacks (XSS attacks). The HTML Editor Extender uses the Provider Model to support different Sanitizer Providers. The July 2011 release of the Ajax Control Toolkit ships with a single Sanitizer Provider which uses the AntiXSS library (see http://AntiXss.CodePlex.com ). A Sanitizer Provider is responsible for sanitizing HTML markup by removing any malicious elements, attributes, and attribute values. For example, the AntiXss Sanitizer Provider will take the following block of HTML: <b><a href=""javascript:doEvil()"">Visit Grandma</a></b> <script>doEvil()</script> And return the following sanitized block of HTML: <b><a href="">Visit Grandma</a></b> Notice that the JavaScript href and <SCRIPT> tag are both stripped out. Be aware that there are a depressingly large number of ways to sneak evil markup into your HTML. You definitely want a Sanitizer as a safety net. Before you can use the AntiXSS Sanitizer Provider, you must add three assemblies to your web application: AntiXSSLibrary.dll, HtmlSanitizationLibrary.dll, and SanitizerProviders.dll. All three assemblies are included with the CodePlex download of the Ajax Control Toolkit in the SanitizerProviders folder. Here’s how you modify your web.config file to use the AntiXSS Sanitizer Provider: <configuration> <configSections> <sectionGroup name="system.web"> <section name="sanitizer" requirePermission="false" type="AjaxControlToolkit.Sanitizer.ProviderSanitizerSection, AjaxControlToolkit"/> </sectionGroup> </configSections> <system.web> <compilation targetFramework="4.0" debug="true"/> <sanitizer defaultProvider="AntiXssSanitizerProvider"> <providers> <add name="AntiXssSanitizerProvider" type="AjaxControlToolkit.Sanitizer.AntiXssSanitizerProvider"></add> </providers> </sanitizer> </system.web> </configuration> You can detect whether the HTML Editor Extender is using the AntiXSS Sanitizer Provider by checking the HtmlEditorExtender SanitizerProvider property like this: if (MyHtmlEditorExtender.SanitizerProvider == null) { throw new Exception("Please enable the AntiXss Sanitizer!"); } When the SanitizerProvider property has the value null, you know that a Sanitizer Provider has not been configured in the web.config file. Because the AntiXSS library requires Full Trust, you cannot use the AntiXSS Sanitizer Provider with most shared website hosting providers. Because most shared hosting providers only support Medium Trust and not Full Trust, we do not recommend using the HTML Editor Extender with a public website hosted with a shared hosting provider. Why a New HTML Editor Control? The Ajax Control Toolkit now includes two HTML Editor controls. Why did we introduce a new HTML Editor control when there was already an existing HTML Editor? We think you will like the new HTML Editor much more than the previous one. We had several goals with the new HTML Editor Extender: Lightweight – We wanted to leverage HTML5 to create a lightweight HTML Editor. The new HTML Editor generates much less markup and script than the previous HTML Editor. Secure – We wanted to make it easy to integrate the AntiXSS library with the HTML Editor. If you are creating a public facing website, we strongly recommend that you use the AntiXSS Provider. Customizable – We wanted to make it easy for users to customize the toolbar buttons displayed by the HTML Editor. Compatibility – We wanted to ensure that the HTML Editor will work with the latest versions of the most popular browsers (including Internet Explorer 6 and higher). The old HTML Editor control is still included in the Ajax Control Toolkit and continues to live in the AjaxControlToolkit.HTMLEditor namespace. We have not modified the control and you can continue to use the control in the same way as you have used it in the past. However, we hope that you will consider migrating to the new HTML Editor Extender for the reasons listed above. Summary We’ve introduced a new Ajax Control Toolkit control with this release. I want to thank the developers and testers on the Superexpert team for the huge amount of work which they put into this control. It was a non-trivial task to build an entirely new control which has the complexity of the HTML Editor in less than 6 weeks. Please let us know what you think! We want to hear your feedback. If you discover issues with the new HTML Editor Extender control, or you have questions about the control, or you have ideas for how it can be improved, then please post them to this blog. Tomorrow starts a new sprint

    Read the article

  • Silverlight 4 Tools for VS 2010 and WCF RIA Services Released

    - by ScottGu
    The final release of the Silverlight 4 Tools for Visual Studio 2010 and WCF RIA Services is now available for download.  Download and Install If you already have Visual Studio 2010 installed (or the free Visual Web Developer 2010 Express), then you can install both the Silverlight 4 Tooling Support as well as WCF RIA Services support by downloading and running this setup package (note: please make sure to uninstall the preview release of the Silverlight 4 Tools for VS 2010 if you have previously installed that).  The Silverlight 4 Tools for VS 2010 package extends the Silverlight support built into Visual Studio 2010 and enables support for Silverlight 4 applications as well.  It also installs WCF RIA Services application templates and libraries: Today’s release includes the English edition of the Silverlight 4 Tooling – localized versions will be available next month for other Visual Studio languages as well. Silverlight Tooling Support Visual Studio 2010 includes rich tooling support for building Silverlight and WPF applications. It includes a WYSIWYG designer surface that enables you to easily use controls to construct UI – including the ability to take advantage of layout containers, and apply styles and resources: The VS 2010 designer enables you to leverage the rich data binding support within Silverlight and WPF, and easily wire-up bindings on controls.  The Data Sources window within Silverlight projects can be used to reference POCO objects (plain old CLR objects), WCF Services, WCF RIA Services client proxies or SharePoint Lists.  For example, let’s assume we add a “Person” class like below to our project: We could then add it to the Data Source window which will cause it to show up like below in the IDE: We can optionally customize the default UI control types that are associated for each property on the object.  For example, below we’ll default the BirthDate property to be represented by a “DatePicker” control: And then when we drag/drop the Person type from the Data Sources onto the design-surface it will automatically create UI controls that are bound to the properties of our Person class: VS 2010 allows you to optionally customize each UI binding further by selecting a control, and then right-click on any of its properties within the property-grid and pull up the “Apply Bindings” dialog: This will bring up a floating data-binding dialog that enables you to easily configure things like the binding path on the data source object, specify a format convertor, specify string-format settings, specify how validation errors should be handled, etc: In addition to providing WYSIWYG designer support for WPF and Silverlight applications, VS 2010 also provides rich XAML intellisense and code editing support – enabling a rich source editing environment. Silverlight 4 Tool Enhancements Today’s Silverlight 4 Tooling Release for VS 2010 includes a bunch of nice new features.  These include: Support for Silverlight Out of Browser Applications and Elevated Trust Applications You can open up a Silverlight application’s project properties window and click the “Enable Running Application Out of Browser” checkbox to enable you to install an offline, out of browser, version of your Silverlight 4 application.  You can then customize a number of “out of browser” settings of your application within Visual Studio: Notice above how you can now indicate that you want to run with elevated trust, with hardware graphics acceleration, as well as customize things like the Window style of the application (allowing you to build a nice polished window style for consumer applications). Support for Implicit Styles and “Go to Value Definition” Support: Silverlight 4 now allows you to define “implicit styles” for your applications.  This allows you to style controls by type (for example: have a default look for all buttons) and avoid you having to explicitly reference styles from each control.  In addition to honoring implicit styles on the designer-surface, VS 2010 also now allows you to right click on any control (or on one of it properties) and choose the “Go to Value Definition…” context menu to jump to the XAML where the style is defined, and from there you can easily navigate onward to any referenced resources.  This makes it much easier to figure out questions like “why is my button red?”: Style Intellisense VS 2010 enables you to easily modify styles you already have in XAML, and now you get intellisense for properties and their values within a style based on the TargetType of the specified control.  For example, below we have a style being set for controls of type “Button” (this is indicated by the “TargetType” property).  Notice how intellisense now automatically shows us properties for the Button control (even within the <Setter> element): Great Video - Watch the Silverlight Designer Features in Action You can see all of the above Silverlight 4 Tools for Visual Studio 2010 features (and some more cool ones I haven’t mentioned) demonstrated in action within this 20 minute Silverlight.TV video on Channel 9: WCF RIA Services Today we also shipped the V1 release of WCF RIA Services.  It is included and automatically installed as part of the Silverlight 4 Tools for Visual Studio 2010 setup. WCF RIA Services makes it much easier to build business applications with Silverlight.  It simplifies the traditional n-tier application pattern by bringing together the ASP.NET and Silverlight platforms using the power of WCF for communication.  WCF RIA Services provides a pattern to write application logic that runs on the mid-tier and controls access to data for queries, changes and custom operations. It also provides end-to-end support for common tasks such as data validation, authentication and authorization based on roles by integrating with Silverlight components on the client and ASP.NET on the mid-tier. Put simply – it makes it much easier to query data stored on a server from a client machine, optionally manipulate/modify the data on the client, and then save it back to the server.  It supports a validation architecture that helps ensure that your data is kept secure and business rules are applied consistently on both the client and middle-tiers. WCF RIA Services uses WCF for communication between the client and the server  It supports both an optimized .NET to .NET binary serialization format, as well as a set of open extensions to the ATOM format known as ODATA and an optional JavaScript Object Notation (JSON) format that can be used by any client. You can hear Nikhil and Dinesh talk a little about WCF RIA Services in this 13 minutes Channel 9 video. Putting it all Together – the Silverlight 4 Training Kit Check out the Silverlight 4 Training Kit to learn more about how to build business applications with Silverlight 4, Visual Studio 2010 and WCF RIA Services. The training kit includes 8 modules, 25 videos, and several hands-on labs that explain Silverlight 4 and WCF RIA Services concepts and walks you through building an end-to-end application with them.    The training kit is available for free and is a great way to get started. Summary I’m really excited about today’s release – as they really complete the Silverlight development story and deliver a great end to end runtime + tooling story for building applications.  All of the above features are available for use both in VS 2010 as well as the free Visual Web Developer 2010 Express Edition – making it really easy to get started building great solutions. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

    Read the article

  • Step by Step:How to use Web Services in ASP.NET AJAX

    - by Yousef_Jadallah
    In my Article Preventing Duplicate Date With ASP.NET AJAX I’ve used ASP.NET AJAX With Web Service Technology, Therefore I add this topic as an introduction how to access Web services from client script in AJAX-enabled ASP.NET Web pages. As well I write this topic to answer the common questions which most of the developers face while working with ASP.NET Ajax Web Services especially in Microsoft ASP.NET official forum http://forums.asp.net/. ASP.NET enables you to create Web services can be accessed from client script in Web pages by using AJAX technology to make Web service calls. Data is exchanged asynchronously between client and server, typically in JSON format.   Lets go a head with the steps :   1-Create a new project , if you are using VS 2005 you have to create ASP.NET Ajax Enabled Web site.   2-Add new Item , Choose Web Service file .     3-To make your Web Services accessible from script, first it must be an .asmx Web service whose Web service class is qualified with the ScriptServiceAttribute attribute and every method you are using to be called from Client script must be qualified with the WebMethodAttribute attribute. On other hand you can use your Web page( CS or VB files) to add static methods accessible from Client Script , just you need to add WebMethod Attribute and set the EnablePageMethods attribute of the ScriptManager control to true..   The other condition is to register the ScriptHandlerFactory HTTP handler, which processes calls made from script to .asmx Web services : <system.web> <httpHandlers> <remove verb="*" path="*.asmx"/> <add verb="*" path="*.asmx" type="System.Web.Script.Services.ScriptHandlerFactory" validate="false"/> </httpHandlers> <system.web> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } but this already added automatically for any Web.config file of any ASP.NET AJAX Enabled WebSite or Project, So you don’t need to add it.   4-Avoid the default Method HelloWorld, then add your method in your asmx file lets say  OurServerOutput , As a consequence your Web service will be like this : using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.Services;     [WebService(Namespace = "http://tempuri.org/")] [WebServiceBinding(ConformsTo = WsiProfiles.BasicProfile1_1)] [System.Web.Script.Services.ScriptService] public class WebService : System.Web.Services.WebService {     [WebMethod] public string OurServerOutput() { return "The Server Date and Time is : " + DateTime.Now.ToString(); } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   5-Add ScriptManager Contol to your aspx file then reference the Web service by adding an asp:ServiceReference child element to the ScriptManager control and setting its path attribute to point to the Web service, That generate a JavaScript proxy class for calling the specified Web service from client script.   <asp:ScriptManager runat="server" ID="scriptManager"> <Services> <asp:ServiceReference Path="WebService.asmx" /> </Services> </asp:ScriptManager> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   Basically ,to enable your application to call Web services(.asmx files) by using client script, the server asynchronous communication layer automatically generates JavaScript proxy classes. A proxy class is generated for each Web service for which an <asp:ServiceReference> element is included under the <asp:ScriptManager> control in the page.   6-Create new button to call the JavaSciprt function and a label to display the returned value . <input id="btnCallDateTime" type="button" value="Call Web Service" onclick="CallDateTime()"/> <asp:Label ID="lblOutupt" runat="server" Text="Label"></asp:Label> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   7-Define the JavaScript code to call the Web Service : <script language="javascript" type="text/javascript">   function CallDateTime() {   WebService.OurServerOutput(OnSucceeded); }   function OnSucceeded(result) { var lblOutput = document.getElementById("lblOutupt"); lblOutput.innerHTML = result; } </script> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } CallDateTime function calls the Web Service Method OurServerOutput… OnSucceeded function Used as the callback function that processes the Web Service return value. which the result parameter is a simple parameter contain the Server Date Time value returned from the Web Service . Finally , when you complete these steps and run your application you can press the button and retrieve Server Date time without postback.   Conclusion: In this topic I describes how to access Web services from client script in AJAX-enabled ASP.NET Web pages With a full .NET Framework/JSON serialize, direct integration with the familiar .asmx Web services ,Using  simple example,Also you can connect with the database to return value by create WebMethod in your Web Service file and the same steps you can use. Next time I will show you more complex example which returns a complex type like objects.   Hope this help.

    Read the article

  • Making Sense of ASP.NET Paths

    - by Rick Strahl
    ASP.Net includes quite a plethora of properties to retrieve path information about the current request, control and application. There's a ton of information available about paths on the Request object, some of it appearing to overlap and some of it buried several levels down, and it can be confusing to find just the right path that you are looking for. To keep things straight I thought it a good idea to summarize the path options along with descriptions and example paths. I wrote a post about this a long time ago in 2004 and I find myself frequently going back to that page to quickly figure out which path I’m looking for in processing the current URL. Apparently a lot of people must be doing the same, because the original post is the second most visited even to this date on this blog to the tune of nearly 500 hits per day. So, I decided to update and expand a bit on the original post with a little more information and clarification based on the original comments. Request Object Paths Available Here's a list of the Path related properties on the Request object (and the Page object). Assume a path like http://www.west-wind.com/webstore/admin/paths.aspx for the paths below where webstore is the name of the virtual. .blackborder td { border-bottom: solid 1px silver; border-left: solid 1px silver; } Request Property Description and Value ApplicationPath Returns the web root-relative logical path to the virtual root of this app. /webstore/ PhysicalApplicationPath Returns local file system path of the virtual root for this app. c:\inetpub\wwwroot\webstore PhysicalPath Returns the local file system path to the current script or path. c:\inetpub\wwwroot\webstore\admin\paths.aspx Path FilePath CurrentExecutionFilePath All of these return the full root relative logical path to the script page including path and scriptname. CurrentExcecutionFilePath will return the ‘current’ request path after a Transfer/Execute call while FilePath will always return the original request’s path. /webstore/admin/paths.aspx AppRelativeCurrentExecutionFilePath Returns an ASP.NET root relative virtual path to the script or path for the current request. If in  a Transfer/Execute call the transferred Path is returned. ~/admin/paths.aspx PathInfo Returns any extra path following the script name. If no extra path is provided returns the root-relative path (returns text in red below). string.Empty if no PathInfo is available. /webstore/admin/paths.aspx/ExtraPathInfo RawUrl Returns the full root relative URL including querystring and extra path as a string. /webstore/admin/paths.aspx?sku=wwhelp40 Url Returns a fully qualified URL including querystring and extra path. Note this is a Uri instance rather than string. http://www.west-wind.com/webstore/admin/paths.aspx?sku=wwhelp40 UrlReferrer The fully qualified URL of the page that sent the request. This is also a Uri instance and this value is null if the page was directly accessed by typing into the address bar or using an HttpClient based Referrer client Http header. http://www.west-wind.com/webstore/default.aspx?Info Control.TemplateSourceDirectory Returns the logical path to the folder of the page, master or user control on which it is called. This is useful if you need to know the path only to a Page or control from within the control. For non-file controls this returns the Page path. /webstore/admin/ As you can see there’s a ton of information available there for each of the three common path formats: Physical Path is an OS type path that points to a path or file on disk. Logical Path is a Web path that is relative to the Web server’s root. It includes the virtual plus the application relative path. ~/ (Root-relative) Path is an ASP.NET specific path that includes ~/ to indicate the virtual root Web path. ASP.NET can convert virtual paths into either logical paths using Control.ResolveUrl(), or physical paths using Server.MapPath(). Root relative paths are useful for specifying portable URLs that don’t rely on relative directory structures and very useful from within control or component code. You should be able to get any necessary format from ASP.NET from just about any path or script using these mechanisms. ~/ Root Relative Paths and ResolveUrl() and ResolveClientUrl() ASP.NET supports root-relative virtual path syntax in most of its URL properties in Web Forms. So you can easily specify a root relative path in a control rather than a location relative path: <asp:Image runat="server" ID="imgHelp" ImageUrl="~/images/help.gif" /> ASP.NET internally resolves this URL by using ResolveUrl("~/images/help.gif") to arrive at the root-relative URL of /webstore/images/help.gif which uses the Request.ApplicationPath as the basepath to replace the ~. By convention any custom Web controls also should use ResolveUrl() on URL properties to provide the same functionality. In your own code you can use Page.ResolveUrl() or Control.ResolveUrl() to accomplish the same thing: string imgPath = this.ResolveUrl("~/images/help.gif"); imgHelp.ImageUrl = imgPath; Unfortunately ResolveUrl() is limited to WebForm pages, so if you’re in an HttpHandler or Module it’s not available. ASP.NET Mvc also has it’s own more generic version of ResolveUrl in Url.Decode: <script src="<%= Url.Content("~/scripts/new.js") %>" type="text/javascript"></script> which is part of the UrlHelper class. In ASP.NET MVC the above sort of syntax is actually even more crucial than in WebForms due to the fact that views are not referencing specific pages but rather are often path based which can lead to various variations on how a particular view is referenced. In a Module or Handler code Control.ResolveUrl() unfortunately is not available which in retrospect seems like an odd design choice – URL resolution really should happen on a Request basis not as part of the Page framework. Luckily you can also rely on the static VirtualPathUtility class: string path = VirtualPathUtility.ToAbsolute("~/admin/paths.aspx"); VirtualPathUtility also many other quite useful methods for dealing with paths and converting between the various kinds of paths supported. One thing to watch out for is that ToAbsolute() will throw an exception if a query string is provided and doesn’t work on fully qualified URLs. I wrote about this topic with a custom solution that works fully qualified URLs and query strings here (check comments for some interesting discussions too). Similar to ResolveUrl() is ResolveClientUrl() which creates a fully qualified HTTP path that includes the protocol and domain name. It’s rare that this full resolution is needed but can be useful in some scenarios. Mapping Virtual Paths to Physical Paths with Server.MapPath() If you need to map root relative or current folder relative URLs to physical URLs or you can use HttpContext.Current.Server.MapPath(). Inside of a Page you can do the following: string physicalPath = Server.MapPath("~/scripts/ww.jquery.js")); MapPath is pretty flexible and it understands both ASP.NET style virtual paths as well as plain relative paths, so the following also works. string physicalPath = Server.MapPath("scripts/silverlight.js"); as well as dot relative syntax: string physicalPath = Server.MapPath("../scripts/jquery.js"); Once you have the physical path you can perform standard System.IO Path and File operations on the file. Remember with physical paths and IO or copy operations you need to make sure you have permissions to access files and folders based on the Web server user account that is active (NETWORK SERVICE, ASPNET typically). Note the Server.MapPath will not map up beyond the virtual root of the application for security reasons. Server and Host Information Between these settings you can get all the information you may need to figure out where you are at and to build new Url if necessary. If you need to build a URL completely from scratch you can get access to information about the server you are accessing: Server Variable Function and Example SERVER_NAME The of the domain or IP Address wwww.west-wind.com or 127.0.0.1 SERVER_PORT The port that the request runs under. 80 SERVER_PORT_SECURE Determines whether https: was used. 0 or 1 APPL_MD_PATH ADSI DirectoryServices path to the virtual root directory. Note that LM typically doesn’t work for ADSI access so you should replace that with LOCALHOST or the machine’s NetBios name. /LM/W3SVC/1/ROOT/webstore Request.Url and Uri Parsing If you still need more control over the current request URL or  you need to create new URLs from an existing one, the current Request.Url Uri property offers a lot of control. Using the Uri class and UriBuilder makes it easy to retrieve parts of a URL and create new URLs based on existing URL. The UriBuilder class is the preferred way to create URLs – much preferable over creating URIs via string concatenation. Uri Property Function Scheme The URL scheme or protocol prefix. http or https Port The port if specifically specified. DnsSafeHost The domain name or local host NetBios machine name www.west-wind.com or rasnote LocalPath The full path of the URL including script name and extra PathInfo. /webstore/admin/paths.aspx Query The query string if any ?id=1 The Uri class itself is great for retrieving Uri parts, but most of the properties are read only if you need to modify a URL in order to change it you can use the UriBuilder class to load up an existing URL and modify it to create a new one. Here are a few common operations I’ve needed to do to get specific URLs: Convert the Request URL to an SSL/HTTPS link For example to take the current request URL and converted  it to a secure URL can be done like this: UriBuilder build = new UriBuilder(Request.Url); build.Scheme = "https"; build.Port = -1; // don't inject port Uri newUri = build.Uri; string newUrl = build.ToString(); Retrieve the fully qualified URL without a QueryString AFAIK, there’s no native routine to retrieve the current request URL without the query string. It’s easy to do with UriBuilder however: UriBuilder builder = newUriBuilder(Request.Url); builder.Query = ""; stringlogicalPathWithoutQuery = builder.ToString(); What else? I took a look through the old post’s comments and addressed as many of the questions and comments that came up in there. With a few small and silly exceptions this update post handles most of these. But I’m sure there are a more things that go in here. What else would be useful to put onto this post so it serves as a nice all in one place to go for path references? If you think of something leave a comment and I’ll try to update the post with it in the future.© Rick Strahl, West Wind Technologies, 2005-2010Posted in ASP.NET  

    Read the article

  • Update information outdated

    - by Achim Krause
    I have a warning triangle that my update information is outdated, the last update was 12 days ago. I use Ubuntu 11.10. A run of sudo apt-get update produces the following output: Ign http://ppa.launchpad.net oneiric InRelease Ign http://de.archive.ubuntu.com oneiric InRelease Ign http://de.archive.ubuntu.com oneiric-updates InRelease Ign http://de.archive.ubuntu.com oneiric-backports InRelease Ign http://security.ubuntu.com oneiric-security InRelease Ign http://extras.ubuntu.com oneiric InRelease Hit http://ppa.launchpad.net oneiric Release.gpg Get:1 http://de.archive.ubuntu.com oneiric Release.gpg [198 B] Hit http://security.ubuntu.com oneiric-security Release.gpg Get:2 http://extras.ubuntu.com oneiric Release.gpg [72 B] Hit http://ppa.launchpad.net oneiric Release Hit http://de.archive.ubuntu.com oneiric-updates Release.gpg Hit http://security.ubuntu.com oneiric-security Release Hit http://extras.ubuntu.com oneiric Release Err http://extras.ubuntu.com oneiric Release Hit http://ppa.launchpad.net oneiric/main Sources Hit http://de.archive.ubuntu.com oneiric-backports Release.gpg Hit http://security.ubuntu.com oneiric-security/main Sources Hit http://ppa.launchpad.net oneiric/main i386 Packages Ign http://ppa.launchpad.net oneiric/main TranslationIndex Ign http://linux.dropbox.com oneiric InRelease Hit http://security.ubuntu.com oneiric-security/restricted Sources Hit http://security.ubuntu.com oneiric-security/universe Sources Hit http://security.ubuntu.com oneiric-security/multiverse Sources Hit http://security.ubuntu.com oneiric-security/main i386 Packages Hit http://security.ubuntu.com oneiric-security/restricted i386 Packages Hit http://security.ubuntu.com oneiric-security/universe i386 Packages Hit http://security.ubuntu.com oneiric-security/multiverse i386 Packages Hit http://security.ubuntu.com oneiric-security/main TranslationIndex Hit http://security.ubuntu.com oneiric-security/multiverse TranslationIndex Hit http://security.ubuntu.com oneiric-security/restricted TranslationIndex Hit http://security.ubuntu.com oneiric-security/universe TranslationIndex Hit http://de.archive.ubuntu.com oneiric Release Hit http://de.archive.ubuntu.com oneiric-updates Release Ign http://de.archive.ubuntu.com oneiric Release Hit http://security.ubuntu.com oneiric-security/main Translation-en Hit http://security.ubuntu.com oneiric-security/multiverse Translation-en Hit http://linux.dropbox.com oneiric Release.gpg Hit http://security.ubuntu.com oneiric-security/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-backports Release Hit http://security.ubuntu.com oneiric-security/universe Translation-en Ign http://de.archive.ubuntu.com oneiric/main Sources/DiffIndex Ign http://de.archive.ubuntu.com oneiric/restricted Sources/DiffIndex Ign http://de.archive.ubuntu.com oneiric/universe Sources/DiffIndex Ign http://de.archive.ubuntu.com oneiric/multiverse Sources/DiffIndex Ign http://de.archive.ubuntu.com oneiric/main i386 Packages/DiffIndex Ign http://de.archive.ubuntu.com oneiric/restricted i386 Packages/DiffIndex Ign http://de.archive.ubuntu.com oneiric/universe i386 Packages/DiffIndex Ign http://de.archive.ubuntu.com oneiric/multiverse i386 Packages/DiffIndex Hit http://linux.dropbox.com oneiric Release Get:3 http://de.archive.ubuntu.com oneiric/main TranslationIndex [3,289 B] Get:4 http://de.archive.ubuntu.com oneiric/multiverse TranslationIndex [2,265 B] Hit http://de.archive.ubuntu.com oneiric/restricted TranslationIndex Get:5 http://de.archive.ubuntu.com oneiric/universe TranslationIndex [2,640 B] Hit http://de.archive.ubuntu.com oneiric-updates/restricted i386 Packages Hit http://de.archive.ubuntu.com oneiric-updates/universe i386 Packages Hit http://de.archive.ubuntu.com oneiric-updates/multiverse i386 Packages Hit http://de.archive.ubuntu.com oneiric-updates/main TranslationIndex Hit http://de.archive.ubuntu.com oneiric-updates/multiverse TranslationIndex Hit http://de.archive.ubuntu.com oneiric-updates/restricted TranslationIndex Hit http://de.archive.ubuntu.com oneiric-updates/universe TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/main Sources Hit http://linux.dropbox.com oneiric/main i386 Packages Ign http://ppa.launchpad.net oneiric/main Translation-en_US Ign http://ppa.launchpad.net oneiric/main Translation-en Ign http://linux.dropbox.com oneiric/main TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/restricted Sources Hit http://de.archive.ubuntu.com oneiric-backports/universe Sources Hit http://de.archive.ubuntu.com oneiric-backports/multiverse Sources Hit http://de.archive.ubuntu.com oneiric-backports/main i386 Packages Hit http://de.archive.ubuntu.com oneiric-backports/restricted i386 Packages Hit http://de.archive.ubuntu.com oneiric-backports/universe i386 Packages Hit http://de.archive.ubuntu.com oneiric-backports/multiverse i386 Packages Hit http://de.archive.ubuntu.com oneiric-backports/main TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/multiverse TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/restricted TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/universe TranslationIndex Hit http://de.archive.ubuntu.com oneiric/main Sources Hit http://de.archive.ubuntu.com oneiric/restricted Sources Hit http://de.archive.ubuntu.com oneiric/universe Sources Hit http://de.archive.ubuntu.com oneiric/multiverse Sources Hit http://de.archive.ubuntu.com oneiric/main i386 Packages Hit http://de.archive.ubuntu.com oneiric/restricted i386 Packages Hit http://de.archive.ubuntu.com oneiric/universe i386 Packages Hit http://de.archive.ubuntu.com oneiric/multiverse i386 Packages Hit http://de.archive.ubuntu.com oneiric/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-updates/main Translation-en Hit http://de.archive.ubuntu.com oneiric-updates/multiverse Translation-en Hit http://de.archive.ubuntu.com oneiric-updates/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-updates/universe Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/main Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/multiverse Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/universe Translation-en Err http://de.archive.ubuntu.com oneiric-updates/main Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Err http://de.archive.ubuntu.com oneiric-updates/restricted Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Err http://de.archive.ubuntu.com oneiric-updates/universe Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Err http://de.archive.ubuntu.com oneiric-updates/multiverse Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Err http://de.archive.ubuntu.com oneiric-updates/main i386 Packages 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Ign http://linux.dropbox.com oneiric/main Translation-en_US Ign http://linux.dropbox.com oneiric/main Translation-en Fetched 273 B in 2s (91 B/s) Reading package lists... Done W: A error occurred during the signature verification. The repository is not updated and the previous index files will be used. GPG error: http://extras.ubuntu.com oneiric Release: The following signatures were invalid: BADSIG 16126D3A3E5C1192 Ubuntu Extras Archive Automatic Signing Key <[email protected]> W: GPG error: http://de.archive.ubuntu.com oneiric Release: The following signatures were invalid: BADSIG 40976EAF437D05B5 Ubuntu Archive Automatic Signing Key <[email protected]> W: Failed to fetch http://extras.ubuntu.com/ubuntu/dists/oneiric/Release W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric/main/i18n/Index No Hash entry in Release file /var/lib/apt/lists/partial/de.archive.ubuntu.com_ubuntu_dists_oneiric_main_i18n_Index W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric/multiverse/i18n/Index No Hash entry in Release file /var/lib/apt/lists/partial/de.archive.ubuntu.com_ubuntu_dists_oneiric_multiverse_i18n_Index W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric/universe/i18n/Index No Hash entry in Release file /var/lib/apt/lists/partial/de.archive.ubuntu.com_ubuntu_dists_oneiric_universe_i18n_Index W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/main/source/Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/restricted/source/Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/universe/source/Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/multiverse/source/Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/main/binary-i386/Packages 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Some index files failed to download. They have been ignored, or old ones used instead. There are some questions with similar problems, but no one seems to get these "Range Not Satisfiable" errors. I do not use a proxy, and the network configuration should not have changed since it worked the last time.

    Read the article

  • Mulit-tenant ASP.NET MVC – Controllers

    - by zowens
    Part I – Introduction Part II – Foundation   The time has come to talk about controllers in a multi-tenant ASP.NET MVC architecture. This is actually the most critical design decision you will make when dealing with multi-tenancy with MVC. In my design, I took into account the design goals I mentioned in the introduction about inversion of control and what a tenant is to my design. Be aware that this is only one way to achieve multi-tenant controllers.   The Premise MvcEx (which is a sample written by Rob Ashton) utilizes dynamic controllers. Essentially a controller is “dynamic” in that multiple action results can be placed in different “controllers” with the same name. This approach is a bit too complicated for my design. I wanted to stick with plain old inheritance when dealing with controllers. The basic premise of my controller design is that my main host defines a set of universal controllers. It is the responsibility of the tenant to decide if the tenant would like to utilize these core controllers. This can be done either by straight usage of the controller or inheritance for extension of the functionality defined by the controller. The controller is resolved by a StructureMap container that is attached to the tenant, as discussed in Part II.   Controller Resolution I have been thinking about two different ways to resolve controllers with StructureMap. One way is to use named instances. This is a really easy way to simply pull the controller right out of the container without a lot of fuss. I ultimately chose not to use this approach. The reason for this decision is to ensure that the controllers are named properly. If a controller has a different named instance that the controller type, then the resolution has a significant disconnect and there are no guarantees. The final approach, the one utilized by the sample, is to simply pull all controller types and correlate the type with a controller name. This has a bit of a application start performance disadvantage, but is significantly more approachable for maintainability. For example, if I wanted to go back and add a “ControllerName” attribute, I would just have to change the ControllerFactory to suit my needs.   The Code The container factory that I have built is actually pretty simple. That’s really all we need. The most significant method is the GetControllersFor method. This method makes the model from the Container and determines all the concrete types for IController.  The thing you might notice is that this doesn’t depend on tenants, but rather containers. You could easily use this controller factory for an application that doesn’t utilize multi-tenancy. public class ContainerControllerFactory : IControllerFactory { private readonly ThreadSafeDictionary<IContainer, IDictionary<string, Type>> typeCache; public ContainerControllerFactory(IContainerResolver resolver) { Ensure.Argument.NotNull(resolver, "resolver"); this.ContainerResolver = resolver; this.typeCache = new ThreadSafeDictionary<IContainer, IDictionary<string, Type>>(); } public IContainerResolver ContainerResolver { get; private set; } public virtual IController CreateController(RequestContext requestContext, string controllerName) { var controllerType = this.GetControllerType(requestContext, controllerName); if (controllerType == null) return null; var controller = this.ContainerResolver.Resolve(requestContext).GetInstance(controllerType) as IController; // ensure the action invoker is a ContainerControllerActionInvoker if (controller != null && controller is Controller && !((controller as Controller).ActionInvoker is ContainerControllerActionInvoker)) (controller as Controller).ActionInvoker = new ContainerControllerActionInvoker(this.ContainerResolver); return controller; } public void ReleaseController(IController controller) { if (controller != null && controller is IDisposable) ((IDisposable)controller).Dispose(); } internal static IEnumerable<Type> GetControllersFor(IContainer container) { Ensure.Argument.NotNull(container); return container.Model.InstancesOf<IController>().Select(x => x.ConcreteType).Distinct(); } protected virtual Type GetControllerType(RequestContext requestContext, string controllerName) { Ensure.Argument.NotNull(requestContext, "requestContext"); Ensure.Argument.NotNullOrEmpty(controllerName, "controllerName"); var container = this.ContainerResolver.Resolve(requestContext); var typeDictionary = this.typeCache.GetOrAdd(container, () => GetControllersFor(container).ToDictionary(x => ControllerFriendlyName(x.Name))); Type found = null; if (typeDictionary.TryGetValue(ControllerFriendlyName(controllerName), out found)) return found; return null; } private static string ControllerFriendlyName(string value) { return (value ?? string.Empty).ToLowerInvariant().Without("controller"); } } One thing to note about my implementation is that we do not use namespaces that can be utilized in the default ASP.NET MVC controller factory. This is something that I don’t use and have no desire to implement and test. The reason I am not using namespaces in this situation is because each tenant has its own namespaces and the routing would not make sense in this case.   Because we are using IoC, dependencies are automatically injected into the constructor. For example, a tenant container could implement it’s own IRepository and a controller could be defined in the “main” project. The IRepository from the tenant would be injected into the main project’s controller. This is quite a useful feature.   Again, the source code is on GitHub here.   Up Next Up next is the view resolution. This is a complicated issue, so be prepared. I hope that you have found this series useful. If you have any questions about my implementation so far, send me an email or DM me on Twitter. I have had a lot of great conversations about multi-tenancy so far and I greatly appreciate the feedback!

    Read the article

  • CodePlex Daily Summary for Friday, February 19, 2010

    CodePlex Daily Summary for Friday, February 19, 2010New ProjectsApplication Management Library: Application Management makes your application life easier. It will automatic do memory management, handle and log unhandled exceptions, profiling y...Audio Service - Play Wave Files From Windows Service: This is a windows service that Check a registry key, when the key is updated with a new wave file path the service plays the wave file.Aviamodels: 3d drawing AviamodelsControl of payment proofs program for Greek citizens: This is a program that is used for Greek citizens who want to keep track of their payment proofs.Cover Creator: Cover Creator gives you the possibility to create and print CD covers. Content of CD is taken from http://www.freedb.org/ or can be added/modyfied ...DevBoard: DevBoard is a webbased scrum tool that helps developers/team get a clear overview of the project progress. It's developed in C# and silverlight.Flex AdventureWorks: The is mostly a skunk-works application to help me get acclimated to CodePlex. The long term goal is to integrate a Flex UI with the AdventureWor...GRE Wordlist: An intuitive and customizable word list for GRE aspirants. Developed in Java using a word list similar to Barron's.Indexer: A desktop file Index and Search tool which allows you to choose a list of folders to index, and then search on later. It is based on Lucene.net an...Project Management Office (PMO) for SharePoint: Sample web part for the Code Mastery event in Boston, February 11, 2010.Restart SQL Audit Policy and Job: Resolve SQL 2008 Audit Network Connectivity Issue.Rounded Corners / DIV Container: The RoundedDiv round corners container is a skin-able, CSS compliant UI control. Select which corners should be rounded, collapse and expand the c...Silverlight Google Search Application: The Silverlight Google Search Application uses Google Search API and behaves like Internet Search Application with option to preview desired page i...Weather Forecast Control: MyWeather forecast control pulls up to date weather forecast information from The Weather Channel for your website.New ReleasesApplication Management Library: ApplicationManagement v1.0: First ReleaseAudio Service - Play Wave Files From Windows Service: Audio Service v1.0: This is a working version of the Audio Service. Please use as you need to.AutoMapper: 1.0.1 for Silverlight 3.0 Alpha: AutoMapper for Silverlight 3.0. Features not supported: IDataReader mapping IListSource mapping All other features are supported.Buzz Dot Net: Buzz Dot Net v.1.10219: Buzz Dot Net Library (Parser & Objects) + WPF Example (using MVVM & Threading)Canvas VSDOC Intellisense: V 1.0.0.0a: This release contains two JavaScript files: canvas-utils.js (can be referenced in both runtime and development environment) canvas-vsdoc.js (must ...Control of payment proofs program for Greek citizens: Payment Proofs: source codeCourier: Beta 2: Added Rx Framework support and re-factored how message registration and un-registration works Blog post explaining the updates and re-factoring c...Cover Creator: Initial release: This is initial stable release. For now only in Polish language.Employee Scheduler: Employee Scheduler 2.2: Small Bug found. Small total hour calculation bug. See http://employeescheduler.codeplex.com/WorkItem/View.aspx?WorkItemId=6059 Extract the files...EnhSim: Release v1.9.7.1: Release v1.9.7.1Implemented Dislodged Foreign Object trinket Whispering Fanged Skull now also procs off Flame shock dots You can toggle bloodlust o...Extend SmallBasic: Teaching Extensions v.007: added SimpleSquareTest added Tortoise.Approve() for virtual proctor how to use virtual proctor: change the path in the proctor.txt file (located i...FolderSize: FolderSize.Win32.1.0.1.0: FolderSize.Win32.1.0.1.0 A simple utility intended to be used to scan harddrives for the folders that take most place and display this to the user...GLB Virtual Player Builder: v0.4.0 Beta: Allows for user to import and use archetypes for building players. The archetypes are contained in the file "archetypes.xml". This file is editab...Google Map WebPart from SharePoint List: GMap Stable Release: GMap Stable ReleaseHenge3D Physics Library for XNA: Henge3D Source (2010-02 R2): Fixed a build error related to an assembly attribute in XBOX 360 builds. Tweaked the controls in the sample when targeting the 360. Reduced the...Indexer: Beta Release 1: Just the initial/rough cut.NukeCS: NukeCS 5.2.3 Source Code: update version to 5.2.3ODOS: ODOS STABLE 1.5.0: Thank you for your patience while we develop this version. Not that much has been added, though. Just doing some sub-conscious stuff to make life...PoshBoard: PoshBoard 3.0 Beta 1: Welcome to the first beta release of PoshBoard 3.0 ! IMPORTANT WARNING : this release is absolutly not feature complete and is error-prone. Okay, ...Restart SQL Audit Policy and Job: Restart SQL 2008 Audit Policy and Job: This folder contains three pieces of source code: Server Audit Status (Started).xml - Import this on-schedule policy into your server's Policy-Ba...SAL- Self Artificial Learning: Artificial Learning 2AQV Working Proof Of Concept: This is the Simulation proof of concept version that comes after the 1aq version. AQ stands for Anwering Questions.SharePoint 2010 Word Automation: SP 2010 Word Automation - Workflow Actions 1.1: This release includes two new custom workflow activities for SharePoint designer Convert Folder Convert Library More information about these new...SharePoint Outlook Connector: Version 1.0.1.1: Exception Logging has been improved.Sharpy: Sharpy 1.2 Alpha: This is the third Sharpy release. A change has been made to allow overriding the master page from the controller. The release contains the single ...Silverlight Google Search Application: SL Google Search App Alpha: This is just a first alpha version of the application, as it looks like when I uploaded it to CodePlex. The application works, requires Silverlight...Starter Kit Mytrip.Mvc.Entity: Mytrip.Mvc.Entity 1.0 RC: EF Membership UserManager FileManager Localization Captcha ClientValidation Theme CrossBrowser VS 2010 RC MVC 2 RC db MSSQL2008thinktecture WSCF.blue: WSCF.blue V1 Update (1.0.6): This release is an update for WSCF.blue V1. Below are the bug fixes made since the V1.0.5 release: The data contract type filter was not including...TS3QueryLib.Net: TS3QueryLib.Net Version 0.18.13.0: Changelog Added overloads to all methods of QueryRunenr class handling permission tasks to allow passing of permission name instead of permissionid...Umbraco CMS: Umbraco 4.1 Beta 2: This is the second beta of Umbraco 4.1. Umbraco 4.1 is more advanced than ever, yet faster, lighter and simpler to use than ever. We, on behalf of...VCC: Latest build, v2.1.30218.0: Automatic drop of latest buildZack's Fiasco - Code Generated DAL: v1.2.4: Enhancements: SQL Server CRUD Stored Procedures added option for USE <db> added option to create or not create INSERT sprocs added option to cr...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)Image Resizer Powertoy Clone for WindowsASP.NETMicrosoft SQL Server Community & SamplesDotNetNuke® Community EditionMost Active ProjectsRawrSharpyDinnerNow.netBlogEngine.NETjQuery Library for SharePoint Web ServicesNB_Store - Free DotNetNuke Ecommerce Catalog Modulepatterns & practices – Enterprise LibraryPHPExcelFacebook Developer ToolkitFluent Ribbon Control Suite

    Read the article

  • Mapping UrlEncoded POST Values in ASP.NET Web API

    - by Rick Strahl
    If there's one thing that's a bit unexpected in ASP.NET Web API, it's the limited support for mapping url encoded POST data values to simple parameters of ApiController methods. When I first looked at this I thought I was doing something wrong, because it seems mighty odd that you can bind query string values to parameters by name, but can't bind POST values to parameters in the same way. To demonstrate here's a simple example. If you have a Web API method like this:[HttpGet] public HttpResponseMessage Authenticate(string username, string password) { …} and then hit with a URL like this: http://localhost:88/samples/authenticate?Username=ricks&Password=sekrit it works just fine. The query string values are mapped to the username and password parameters of our API method. But if you now change the method to work with [HttpPost] instead like this:[HttpPost] public HttpResponseMessage Authenticate(string username, string password) { …} and hit it with a POST HTTP Request like this: POST http://localhost:88/samples/authenticate HTTP/1.1 Host: localhost:88 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Content-type: application/x-www-form-urlencoded Content-Length: 30 Username=ricks&Password=sekrit you'll find that while the request works, it doesn't actually receive the two string parameters. The username and password parameters are null and so the method is definitely going to fail. When I mentioned this over Twitter a few days ago I got a lot of responses back of why I'd want to do this in the first place - after all HTML Form submissions are the domain of MVC and not WebAPI which is a valid point. However, the more common use case is using POST Variables with AJAX calls. The following is quite common for passing simple values:$.post(url,{ Username: "Rick", Password: "sekrit" },function(result) {…}); but alas that doesn't work. How ASP.NET Web API handles Content Bodies Web API supports parsing content data in a variety of ways, but it does not deal with multiple posted content values. In effect you can only post a single content value to a Web API Action method. That one parameter can be very complex and you can bind it in a variety of ways, but ultimately you're tied to a single POST content value in your parameter definition. While it's possible to support multiple parameters on a POST/PUT operation, only one parameter can be mapped to the actual content - the rest have to be mapped to route values or the query string. Web API treats the whole request body as one big chunk of data that is sent to a Media Type Formatter that's responsible for de-serializing the content into whatever value the method requires. The restriction comes from async nature of Web API where the request data is read only once inside of the formatter that retrieves and deserializes it. Because it's read once, checking for content (like individual POST variables) first is not possible. However, Web API does provide a couple of ways to access the form POST data: Model Binding - object property mapping to bind POST values FormDataCollection - collection of POST keys/values ModelBinding POST Values - Binding POST data to Object Properties The recommended way to handle POST values in Web API is to use Model Binding, which maps individual urlencoded POST values to properties of a model object provided as the parameter. Model binding requires a single object as input to be bound to the POST data, with each POST key that matches a property name (including nested properties like Address.Street) being mapped and updated including automatic type conversion of simple types. This is a very nice feature - and a familiar one from MVC - that makes it very easy to have model objects mapped directly from inbound data. The obvious drawback with Model Binding is that you need a model for it to work: You have to provide a strongly typed object that can receive the data and this object has to map the inbound data. To rewrite the example above to use ModelBinding I have to create a class maps the properties that I need as parameters:public class LoginData { public string Username { get; set; } public string Password { get; set; } } and then accept the data like this in the API method:[HttpPost] public HttpResponseMessage Authenticate(LoginData login) { string username = login.Username; string password = login.Password; … } This works fine mapping the POST values to the properties of the login object. As a side benefit of this method definition, the method now also allows posting of JSON or XML to the same endpoint. If I change my request to send JSON like this: POST http://localhost:88/samples/authenticate HTTP/1.1 Host: localhost:88 Accept: application/jsonContent-type: application/json Content-Length: 40 {"Username":"ricks","Password":"sekrit"} it works as well and transparently, courtesy of the nice Content Negotiation features of Web API. There's nothing wrong with using Model binding and in fact it's a common practice to use (view) model object for inputs coming back from the client and mapping them into these models. But it can be  kind of a hassle if you have AJAX applications with a ton of backend hits, especially if many methods are very atomic and focused and don't effectively require a model or view. Not always do you have to pass structured data, but sometimes there are just a couple of simple response values that need to be sent back. If all you need is to pass a couple operational parameters, creating a view model object just for parameter purposes seems like overkill. Maybe you can use the query string instead (if that makes sense), but if you can't then you can often end up with a plethora of 'message objects' that serve no further  purpose than to make Model Binding work. Note that you can accept multiple parameters with ModelBinding so the following would still work:[HttpPost] public HttpResponseMessage Authenticate(LoginData login, string loginDomain) but only the object will be bound to POST data. As long as loginDomain comes from the querystring or route data this will work. Collecting POST values with FormDataCollection Another more dynamic approach to handle POST values is to collect POST data into a FormDataCollection. FormDataCollection is a very basic key/value collection (like FormCollection in MVC and Request.Form in ASP.NET in general) and then read the values out individually by querying each. [HttpPost] public HttpResponseMessage Authenticate(FormDataCollection form) { var username = form.Get("Username"); var password = form.Get("Password"); …} The downside to this approach is that it's not strongly typed, you have to handle type conversions on non-string parameters, and it gets a bit more complicated to test such as setup as you have to seed a FormDataCollection with data. On the other hand it's flexible and easy to use and especially with string parameters is easy to deal with. It's also dynamic, so if the client sends you a variety of combinations of values on which you make operating decisions, this is much easier to work with than a strongly typed object that would have to account for all possible values up front. The downside is that the code looks old school and isn't as self-documenting as a parameter list or object parameter would be. Nevertheless it's totally functionality and a viable choice for collecting POST values. What about [FromBody]? Web API also has a [FromBody] attribute that can be assigned to parameters. If you have multiple parameters on a Web API method signature you can use [FromBody] to specify which one will be parsed from the POST content. Unfortunately it's not terribly useful as it only returns content in raw format and requires a totally non-standard format ("=content") to specify your content. For more info in how FromBody works and several related issues to how POST data is mapped, you can check out Mike Stalls post: How WebAPI does Parameter Binding Not really sure where the Web API team thought [FromBody] would really be a good fit other than a down and dirty way to send a full string buffer. Extending Web API to make multiple POST Vars work? Don't think so Clearly there's no native support for multiple POST variables being mapped to parameters, which is a bit of a bummer. I know in my own work on one project my customer actually found this to be a real sticking point in their AJAX backend work, and we ended up not using Web API and using MVC JSON features instead. That's kind of sad because Web API is supposed to be the proper solution for AJAX backends. With all of ASP.NET Web API's extensibility you'd think there would be some way to build this functionality on our own, but after spending a bit of time digging and asking some of the experts from the team and Web API community I didn't hear anything that even suggests that this is possible. From what I could find I'd say it's not possible primarily because Web API's Routing engine does not account for the POST variable mapping. This means [HttpPost] methods with url encoded POST buffers are not mapped to the parameters of the endpoint, and so the routes would never even trigger a request that could be intercepted. Once the routing doesn't work there's not much that can be done. If somebody has an idea how this could be accomplished I would love to hear about it. Do we really need multi-value POST mapping? I think that that POST value mapping is a feature that one would expect of any API tool to have. If you look at common APIs out there like Flicker and Google Maps etc. they all work with POST data. POST data is very prominent much more so than JSON inputs and so supporting as many options that enable would seem to be crucial. All that aside, Web API does provide very nice features with Model Binding that allows you to capture many POST variables easily enough, and logistically this will let you build whatever you need with POST data of all shapes as long as you map objects. But having to have an object for every operation that receives a data input is going to take its toll in heavy AJAX applications, with a lot of types created that do nothing more than act as parameter containers. I also think that POST variable mapping is an expected behavior and Web APIs non-support will likely result in many, many questions like this one: How do I bind a simple POST value in ASP.NET WebAPI RC? with no clear answer to this question. I hope for V.next of WebAPI Microsoft will consider this a feature that's worth adding. Related Articles Passing multiple POST parameters to Web API Controller Methods Mike Stall's post: How Web API does Parameter Binding Where does ASP.NET Web API Fit?© Rick Strahl, West Wind Technologies, 2005-2012Posted in Web Api   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

    Read the article

  • Quartz.Net Writing your first Hello World Job

    - by Tarun Arora
    In this blog post I’ll be covering, 01: A few things to consider before you should schedule a Job using Quartz.Net 02: Setting up your solution to use Quartz.Net API 03: Quartz.Net configuration 04: Writing & scheduling a hello world job with Quartz.Net If you are new to Quartz.Net I would recommend going through, A brief introduction to Quartz.net Walkthrough of Installing & Testing Quartz.Net as a Windows Service A few things to consider before you should schedule a Job using Quartz.Net - An instance of the scheduler service - A trigger - And last but not the least a job For example, if I wanted to schedule a script to run on the server, I should be jotting down answers to the below questions, a. Considering there are multiple machines set up with Quartz.Net windows service, how can I choose the instance of Quartz.Net where I want my script to be run b. What will trigger the execution of the job c. How often do I want the job to run d. Do I want the job to run right away or start after a delay or may be have the job start at a specific time e. What will happen to my job if Quartz.Net windows service is reset f. Do I want multiple instances of this job to run concurrently g. Can I pass parameters to the job being executed by Quartz.Net windows service Setting up your solution to use Quartz.Net API 1. Create a new C# Console Application project and call it “HelloWorldQuartzDotNet” and add a reference to Quartz.Net.dll. I use the NuGet Package Manager to add the reference. This can be done by right clicking references and choosing Manage NuGet packages, from the Nuget Package Manager choose Online from the left panel and in the search box on the right search for Quartz.Net. Click Install on the package “Quartz” (Screen shot below). 2. Right click the project and choose Add New Item. Add a new Interface and call it ‘IScheduledJob.cs’. Mark the Interface public and add the signature for Run. Your interface should look like below. namespace HelloWorldQuartzDotNet { public interface IScheduledJob { void Run(); } }   3. Right click the project and choose Add new Item. Add a class and call it ‘Scheduled Job’. Use this class to implement the interface ‘IscheduledJob.cs’. Look at the pseudo code in the implementation of the Run method. using System; namespace HelloWorldQuartzDotNet { class ScheduledJob : IScheduledJob { public void Run() { // Get an instance of the Quartz.Net scheduler // Define the Job to be scheduled // Associate a trigger with the Job // Assign the Job to the scheduler throw new NotImplementedException(); } } }   I’ll get into the implementation in more detail, but let’s look at the minimal configuration a sample configuration file for Quartz.Net service to work. Quartz.Net configuration In the App.Config file copy the below configuration <?xml version="1.0" encoding="utf-8" ?> <configuration> <configSections> <section name="quartz" type="System.Configuration.NameValueSectionHandler, System, Version=1.0.5000.0,Culture=neutral, PublicKeyToken=b77a5c561934e089" /> </configSections> <quartz> <add key="quartz.scheduler.instanceName" value="ServerScheduler" /> <add key="quartz.threadPool.type" value="Quartz.Simpl.SimpleThreadPool, Quartz" /> <add key="quartz.threadPool.threadCount" value="10" /> <add key="quartz.threadPool.threadPriority" value="2" /> <add key="quartz.jobStore.misfireThreshold" value="60000" /> <add key="quartz.jobStore.type" value="Quartz.Simpl.RAMJobStore, Quartz" /> </quartz> </configuration>   As you can see in the configuration above, I have included the instance name of the quartz scheduler, the thread pool type, count and priority, the job store type has been defined as RAM. You have the option of configuring that to ADO.NET JOB store. More details here. Writing & scheduling a hello world job with Quartz.Net Once fully implemented the ScheduleJob.cs class should look like below. I’ll walk you through the details of the implementation… - GetScheduler() uses the name of the quartz.net and listens on localhost port 555 to try and connect to the quartz.net windows service. - Run() an attempt is made to start the scheduler in case it is in standby mode - I have defined a job “WriteHelloToConsole” (that’s the name of the job), this job belongs to the group “IT”. Think of group as a logical grouping feature. It helps you bucket jobs into groups. Quartz.Net gives you the ability to pause or delete all jobs in a group (We’ll look at that in some of the future posts). I have requested for recovery of this job in case the quartz.net service fails over to the other node in the cluster. The jobType is “HelloWorldJob”. This is the class that would be called to execute the job. More details on this below… - I have defined a trigger for my job. I have called the trigger “WriteHelloToConsole”. The Trigger works on the cron schedule “0 0/1 * 1/1 * ? *” which means fire the job once every minute. I would recommend that you look at www.cronmaker.com a free and great website to build and parse cron expressions. The trigger has a priority 1. So, if two jobs are run at the same time, this trigger will have high priority and will be run first. - Use the Job and Trigger to schedule the job. This method returns a datetime offeset. It is possible to see the next fire time for the job from this variable. using System.Collections.Specialized; using System.Configuration; using Quartz; using System; using Quartz.Impl; namespace HelloWorldQuartzDotNet { class ScheduledJob : IScheduledJob { public void Run() { // Get an instance of the Quartz.Net scheduler var schd = GetScheduler(); // Start the scheduler if its in standby if (!schd.IsStarted) schd.Start(); // Define the Job to be scheduled var job = JobBuilder.Create<HelloWorldJob>() .WithIdentity("WriteHelloToConsole", "IT") .RequestRecovery() .Build(); // Associate a trigger with the Job var trigger = (ICronTrigger)TriggerBuilder.Create() .WithIdentity("WriteHelloToConsole", "IT") .WithCronSchedule("0 0/1 * 1/1 * ? *") // visit http://www.cronmaker.com/ Queues the job every minute .WithPriority(1) .Build(); // Assign the Job to the scheduler var schedule = schd.ScheduleJob(job, trigger); Console.WriteLine("Job '{0}' scheduled for '{1}'", "", schedule.ToString("r")); } // Get an instance of the Quartz.Net scheduler private static IScheduler GetScheduler() { try { var properties = new NameValueCollection(); properties["quartz.scheduler.instanceName"] = "ServerScheduler"; // set remoting expoter properties["quartz.scheduler.proxy"] = "true"; properties["quartz.scheduler.proxy.address"] = string.Format("tcp://{0}:{1}/{2}", "localhost", "555", "QuartzScheduler"); // Get a reference to the scheduler var sf = new StdSchedulerFactory(properties); return sf.GetScheduler(); } catch (Exception ex) { Console.WriteLine("Scheduler not available: '{0}'", ex.Message); throw; } } } }   The above highlighted values have been taken from the Quartz.config file, this file is available in the Quartz.net server installation directory. Implementation of my HelloWorldJob Class below. The HelloWorldJob class gets called to execute the job “WriteHelloToConsole” using the once every minute trigger set up for this job. The HelloWorldJob is a class that implements the interface IJob. I’ll walk you through the details of the implementation… - context is passed to the method execute by the quartz.net scheduler service. This has everything you need to pull out the job, trigger specific information. - for example. I have pulled out the value of the jobKey name, the fire time and next fire time. using Quartz; using System; namespace HelloWorldQuartzDotNet { class HelloWorldJob : IJob { public void Execute(IJobExecutionContext context) { try { Console.WriteLine("Job {0} fired @ {1} next scheduled for {2}", context.JobDetail.Key, context.FireTimeUtc.Value.ToString("r"), context.NextFireTimeUtc.Value.ToString("r")); Console.WriteLine("Hello World!"); } catch (Exception ex) { Console.WriteLine("Failed: {0}", ex.Message); } } } }   I’ll add a call to call the scheduler in the Main method in Program.cs using System; using System.Threading; namespace HelloWorldQuartzDotNet { class Program { static void Main(string[] args) { try { var sj = new ScheduledJob(); sj.Run(); Thread.Sleep(10000 * 10000); } catch (Exception ex) { Console.WriteLine("Failed: {0}", ex.Message); } } } }   This was third in the series of posts on enterprise scheduling using Quartz.net, in the next post I’ll be covering how to pass parameters to the scheduled task scheduled on Quartz.net windows service. Thank you for taking the time out and reading this blog post. If you enjoyed the post, remember to subscribe to http://feeds.feedburner.com/TarunArora. Stay tuned!

    Read the article

  • float right image pushes down text in table below in IE9 [migrated]

    - by Cheers and hth. - Alf
    I'm not a webmaster, not even a web developer, but I'm tasked with adding content to a Wordpress site developed by Someone Else(TM). Here's a page illustrating the problem: http://www.reginedagan.no/program/fiskekonkurranse-i-hovden/. It shows up nice in Firefox: But in IE9 the floated picture pushed down the text in the table below, so that it looks rather awful: I found some related questions on the web, e.g. "CSS: Float right in IE doesn't work!" and "why does a floating DIV mess up table positioning?", and the suggestions there led me to set clear: none on the div around the table, the table itself, and then each individual tr and finally even on each individual td. I also set width="99%" on the table, and tried (but I don't know how correctly) to apply the IE6 quirk fix margin-right: -3px. So here's the content as written in Wordpress, including the unsuccessful attempted fixes: <h1><div style="float: right"><a href="http://www.reginedagan.no/?attachment_id=671"><img src="http://www.reginedagan.no/wp-content/uploads/2012/06/fiskekonkurranse-2011-bilde-3-nedskalert.jpg" alt="Fra fiskekonkurransen i 2011" title="Fra fiskekonkurransen i 2011" width="200" height="242" class="size-full wp-image-671"/></a></div>Fiskekonkurranse i Hovden!</h1> <div style="background-color: #FAF0F0; clear: none;"><table width="99%" style="clear: none; right-margin: -3px;"> <tr style=" clear: none;"> <td style="text-align: left; clear: none;">Dato:</td> <td style="text-align: left; clear: none;">Lørdag 21.juli</td> </tr> <tr style=" clear: none;"> <td style="text-align: left; padding-left: 2em"; clear: none;>/ barn, Flytebrygga</td> <td style="text-align: left; clear: none;">15.00 &ndash; 16.00</td> </tr> <tr style=" clear: none;"> <td style="text-align: left; padding-left: 2em; clear: none;">/ voksne (over 12 år), Moloen</td> <td style="text-align: left; clear: none;">15.00 &ndash; 17.00 </td> </tr> <tr style=" clear: none;"> <td style="text-align: left; clear: none;">Sted:</td> <td style="text-align: left; clear: none;">Hovden</td> </tr> <tr style=" clear: none;"> <td style="text-align: left; clear: none;">Pris:</td> <td style="text-align: left; clear: none;">voksen (over 12 år) kr. 50,-, barn kr. 30,-</td> </tr style=" clear: none;"> <tr> <td style="text-align: left; clear: none;">Arrangør:</td> <td style="text-align: left; clear: none;">Hovden Grendelag</td> </tr> </table></div> Velkommen til den årlige Fiskekonkurransen i Hovden lørdag 21. juli! <a href="http://www.reginedagan.no/program/fiskekonkurranse-i-hovden/fiskekonkurranse-2011-bilde-nedskalertjpg/" rel="attachment wp-att-672"><img src="http://www.reginedagan.no/wp-content/uploads/2012/03/fiskekonkurranse-2011-bilde-nedskalertjpg.jpg" alt="Fra fiskekonkurransen i 2011" title="Fra fiskekonkurransen i 2011" width="400" height="267" class="alignleft size-full wp-image-672" /></a>Det blir stangfiske fra moloen og egen barnekonkurranse fra flytebrygga. Premiering for størst fisk, størst antall kg og flest antall stk. Premiering for barn kl. 16:30 på moloen. Alle premieres. Premiering for voksne på festen om kvelden. Salg av pølser og brus, vafler og kaffe, samt sluker. <div style="clear: left; border: 1px dashed gray; padding: 1em;"> Fest på Hovden samfunnshus kl. 21 &ndash; 02. Musikk: «Mister West», Steinar Aarsnes, Andøya. CC. Salg av øl/vin og snacks. </div> VEL MØTT &mdash; SKITT FISKE! And the resulting HTML served to a browser (only the relevant first part): <div style="float: right;"><a href="http://www.reginedagan.no/?attachment_id=671"><img src="http://www.reginedagan.no/wp-content/uploads/2012/06/fiskekonkurranse-2011-bilde-3-nedskalert.jpg" alt="Fra fiskekonkurransen i 2011" title="Fra fiskekonkurransen i 2011" class="size-full wp-image-671" height="242" width="200"></a></div> <p>Fiskekonkurranse i Hovden!</p></h1> <div style="background-color: rgb(250, 240, 240); clear: none;"> <table style="clear: none;" width="99%"> <tbody><tr style="clear: none;"> <td style="text-align: left; clear: none;">Dato:</td> <td style="text-align: left; clear: none;">Lørdag 21.juli</td> </tr> The able to reproduce the effect with simpler code by setting clear: right on the table. However, I'm unable to reproduce the effect with default styling or with clear: none (as above). So it seems maybe it's something Wordpress does, or maybe it's something the theme thing or whatever it is does – but it's very similar to what others have observed, so there is strong indication that it's also a quirk in IE. Help?

    Read the article

  • MySQL Connect: What to Expect From the Wondrous Land of MySQL Cluster

    - by Mat Keep
    The MySQL Connect conference is only a couple of weeks away, with MySQL engineers, support teams, consultants and community aces busy putting the final touches to their talks. There will be many exciting new announcements and sharing of best practices at the conference, covering the range of MySQL technologies. MySQL Cluster will a big part of this, so I wanted to share some key sessions for those of you who plan on attending, as well as some resources for those who are not lucky enough to be able to make the trip, but who can't afford to miss the key news. Of course, this is no substitute to actually being there….and the good news is that registration is still open ;-) Roadmap: Whats New in MySQL Cluster Saturday 29th, 1300-1400, in Golden Gate room 5.                                                                                        Bernd Ocklin, director of MySQL Cluster development, and myself will be taking a look at what follows the latest MySQL Cluster 7.2 release. I don't want to give to much away - lets just say its not often you can add powerful new functionality to a product while at the same time making life radically simpler for its users. For those not making it to the Conference, a live webinar repeating the talk is scheduled for Thursday 25th October at 09.00 pacific time. Hold the date, registration will be open for that soon and published to our MySQL Webinars page Best Practices Getting Started with MySQL Cluster, Hands-On Lab Saturday 29th, 1600-1700, in Plaza Room A.                                                              Santo Leto, one of our lead MySQL Cluster support engineers, regularly works with users new to MySQL Cluster, assisting them in installation, configuration, scaling, etc. In this lab, Santo will share best-practices in getting started. Delivering Breakthrough Performance with MySQL Cluster Saturday 29th, 1730-1830, in Golden Gate room 5. Frazer Clement, lead MySQL Cluster software engineer, will demonstrate how to translate the awesome Cluster benchmarks (remember 1 BILLION UPDATEs per minute ?!) into real-world performance. You can also get some best practices from our new MySQL Cluster performance guide  MySQL Cluster BoF Saturday 29th, 1900-2000, room Golden Gate 5.                                                                                                           Come and get a demonstration of new tools for the installation and configuration of MySQL Cluster, and spend time with the engineering team discussing any questions or issues you may have. Developing High-Throughput Services with NoSQL APIs to InnoDB and MySQL Cluster Sunday 30th, 1145 - 1245, in Golden Gate room 7.   In this session, JD Duncan and Andrew Morgan will present how to get started with both Memcached and new NoSQL APIs. JD and I recently ran a webinar demonstrating how to build simple Twitter-like services with Memcached and MySQL Cluster. The replay is available for download.  Case Studies: MySQL Cluster @ El Chavo, Latin America’s #1 Facebook Game Sunday 30th, 1745 - 1845, in Golden Gate room 4.                             Playful Play deployed MySQL Cluster CGE to power their market leading social game. This session will discuss the challenges they faced, why they selected MySQL Cluster and their experiences to date. You can read more about Playful Play and MySQL Cluster here  A Journey into NoSQLand: MySQL’s NoSQL Implementation Sunday 30th, 1345 - 1445, in Golden Gate room 4.                                          Lig Turmelle, web DBA at Kaplan Professional and esteemed Oracle Ace, will discuss her experiences working with the NoSQL interfaces for both MySQL Cluster and InnoDB Evaluating MySQL HA Alternatives Saturday 29th, 1430-1530, room Golden Gate 5                                                                                   Henrik Ingo, former member of the MySQL sales engineering team, will provide an overview of various HA technologies for MySQL, starting with replication, progressing to InnoDB, Galera and MySQL Cluster What about the other stuff? Of course MySQL Connect has much, much more than MySQL Cluster. There will be lots on replication (which I'll blog about soon), MySQL 5.6, InnoDB, cloud, etc, etc. Take a look at the full Content Catalog to see more. If you are attending, I hope to see you at one of the Cluster sessions...and remember, registration is still open

    Read the article

  • SQL SERVER – How to Recover SQL Database Data Deleted by Accident

    - by Pinal Dave
    In Repair a SQL Server database using a transaction log explorer, I showed how to use ApexSQL Log, a SQL Server transaction log viewer, to recover a SQL Server database after a disaster. In this blog, I’ll show you how to use another SQL Server disaster recovery tool from ApexSQL in a situation when data is accidentally deleted. You can download ApexSQL Recover here, install, and play along. With a good SQL Server disaster recovery strategy, data recovery is not a problem. You have a reliable full database backup with valid data, a full database backup and subsequent differential database backups, or a full database backup and a chain of transaction log backups. But not all situations are ideal. Here we’ll address some sub-optimal scenarios, where you can still successfully recover data. If you have only a full database backup This is the least optimal SQL Server disaster recovery strategy, as it doesn’t ensure minimal data loss. For example, data was deleted on Wednesday. Your last full database backup was created on Sunday, three days before the records were deleted. By using the full database backup created on Sunday, you will be able to recover SQL database records that existed in the table on Sunday. If there were any records inserted into the table on Monday or Tuesday, they will be lost forever. The same goes for records modified in this period. This method will not bring back modified records, only the old records that existed on Sunday. If you restore this full database backup, all your changes (intentional and accidental) will be lost and the database will be reverted to the state it had on Sunday. What you have to do is compare the records that were in the table on Sunday to the records on Wednesday, create a synchronization script, and execute it against the Wednesday database. If you have a full database backup followed by differential database backups Let’s say the situation is the same as in the example above, only you create a differential database backup every night. Use the full database backup created on Sunday, and the last differential database backup (created on Tuesday). In this scenario, you will lose only the data inserted and updated after the differential backup created on Tuesday. If you have a full database backup and a chain of transaction log backups This is the SQL Server disaster recovery strategy that provides minimal data loss. With a full chain of transaction logs, you can recover the SQL database to an exact point in time. To provide optimal results, you have to know exactly when the records were deleted, because restoring to a later point will not bring back the records. This method requires restoring the full database backup first. If you have any differential log backup created after the last full database backup, restore the most recent one. Then, restore transaction log backups, one by one, it the order they were created starting with the first created after the restored differential database backup. Now, the table will be in the state before the records were deleted. You have to identify the deleted records, script them and run the script against the original database. Although this method is reliable, it is time-consuming and requires a lot of space on disk. How to easily recover deleted records? The following solution enables you to recover SQL database records even if you have no full or differential database backups and no transaction log backups. To understand how ApexSQL Recover works, I’ll explain what happens when table data is deleted. Table data is stored in data pages. When you delete table records, they are not immediately deleted from the data pages, but marked to be overwritten by new records. Such records are not shown as existing anymore, but ApexSQL Recover can read them and create undo script for them. How long will deleted records stay in the MDF file? It depends on many factors, as time passes it’s less likely that the records will not be overwritten. The more transactions occur after the deletion, the more chances the records will be overwritten and permanently lost. Therefore, it’s recommended to create a copy of the database MDF and LDF files immediately (if you cannot take your database offline until the issue is solved) and run ApexSQL Recover on them. Note that a full database backup will not help here, as the records marked for overwriting are not included in the backup. First, I’ll delete some records from the Person.EmailAddress table in the AdventureWorks database.   I can delete these records in SQL Server Management Studio, or execute a script such as DELETE FROM Person.EmailAddress WHERE BusinessEntityID BETWEEN 70 AND 80 Then, I’ll start ApexSQL Recover and select From DELETE operation in the Recovery tab.   In the Select the database to recover step, first select the SQL Server instance. If it’s not shown in the drop-down list, click the Server icon right to the Server drop-down list and browse for the SQL Server instance, or type the instance name manually. Specify the authentication type and select the database in the Database drop-down list.   In the next step, you’re prompted to add additional data sources. As this can be a tricky step, especially for new users, ApexSQL Recover offers help via the Help me decide option.   The Help me decide option guides you through a series of questions about the database transaction log and advises what files to add. If you know that you have no transaction log backups or detached transaction logs, or the online transaction log file has been truncated after the data was deleted, select No additional transaction logs are available. If you know that you have transaction log backups that contain the delete transactions you want to recover, click Add transaction logs. The online transaction log is listed and selected automatically.   Click Add if to add transaction log backups. It would be best if you have a full transaction log chain, as explained above. The next step for this option is to specify the time range.   Selecting a small time range for the time of deletion will create the recovery script just for the accidentally deleted records. A wide time range might script the records deleted on purpose, and you don’t want that. If needed, you can check the script generated and manually remove such records. After that, for all data sources options, the next step is to select the tables. Be careful here, if you deleted some data from other tables on purpose, and don’t want to recover them, don’t select all tables, as ApexSQL Recover will create the INSERT script for them too.   The next step offers two options: to create a recovery script that will insert the deleted records back into the Person.EmailAddress table, or to create a new database, create the Person.EmailAddress table in it, and insert the deleted records. I’ll select the first one.   The recovery process is completed and 11 records are found and scripted, as expected.   To see the script, click View script. ApexSQL Recover has its own script editor, where you can review, modify, and execute the recovery script. The insert into statements look like: INSERT INTO Person.EmailAddress( BusinessEntityID, EmailAddressID, EmailAddress, rowguid, ModifiedDate) VALUES( 70, 70, N'[email protected]' COLLATE SQL_Latin1_General_CP1_CI_AS, 'd62c5b4e-c91f-403f-b630-7b7e0fda70ce', '20030109 00:00:00.000' ); To execute the script, click Execute in the menu.   If you want to check whether the records are really back, execute SELECT * FROM Person.EmailAddress WHERE BusinessEntityID BETWEEN 70 AND 80 As shown, ApexSQL Recover recovers SQL database data after accidental deletes even without the database backup that contains the deleted data and relevant transaction log backups. ApexSQL Recover reads the deleted data from the database data file, so this method can be used even for databases in the Simple recovery model. Besides recovering SQL database records from a DELETE statement, ApexSQL Recover can help when the records are lost due to a DROP TABLE, or TRUNCATE statement, as well as repair a corrupted MDF file that cannot be attached to as SQL Server instance. You can find more information about how to recover SQL database lost data and repair a SQL Server database on ApexSQL Solution center. There are solutions for various situations when data needs to be recovered. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: PostADay, SQL, SQL Authority, SQL Backup and Restore, SQL Query, SQL Server, SQL Tips and Tricks, T SQL

    Read the article

  • Transactional Messaging in the Windows Azure Service Bus

    - by Alan Smith
    Introduction I’m currently working on broadening the content in the Windows Azure Service Bus Developer Guide. One of the features I have been looking at over the past week is the support for transactional messaging. When using the direct programming model and the WCF interface some, but not all, messaging operations can participate in transactions. This allows developers to improve the reliability of messaging systems. There are some limitations in the transactional model, transactions can only include one top level messaging entity (such as a queue or topic, subscriptions are no top level entities), and transactions cannot include other systems, such as databases. As the transaction model is currently not well documented I have had to figure out how things work through experimentation, with some help from the development team to confirm any questions I had. Hopefully I’ve got the content mostly correct, I will update the content in the e-book if I find any errors or improvements that can be made (any feedback would be very welcome). I’ve not had a chance to look into the code for transactions and asynchronous operations, maybe that would make a nice challenge lab for my Windows Azure Service Bus course. Transactional Messaging Messaging entities in the Windows Azure Service Bus provide support for participation in transactions. This allows developers to perform several messaging operations within a transactional scope, and ensure that all the actions are committed or, if there is a failure, none of the actions are committed. There are a number of scenarios where the use of transactions can increase the reliability of messaging systems. Using TransactionScope In .NET the TransactionScope class can be used to perform a series of actions in a transaction. The using declaration is typically used de define the scope of the transaction. Any transactional operations that are contained within the scope can be committed by calling the Complete method. If the Complete method is not called, any transactional methods in the scope will not commit.   // Create a transactional scope. using (TransactionScope scope = new TransactionScope()) {     // Do something.       // Do something else.       // Commit the transaction.     scope.Complete(); }     In order for methods to participate in the transaction, they must provide support for transactional operations. Database and message queue operations typically provide support for transactions. Transactions in Brokered Messaging Transaction support in Service Bus Brokered Messaging allows message operations to be performed within a transactional scope; however there are some limitations around what operations can be performed within the transaction. In the current release, only one top level messaging entity, such as a queue or topic can participate in a transaction, and the transaction cannot include any other transaction resource managers, making transactions spanning a messaging entity and a database not possible. When sending messages, the send operations can participate in a transaction allowing multiple messages to be sent within a transactional scope. This allows for “all or nothing” delivery of a series of messages to a single queue or topic. When receiving messages, messages that are received in the peek-lock receive mode can be completed, deadlettered or deferred within a transactional scope. In the current release the Abandon method will not participate in a transaction. The same restrictions of only one top level messaging entity applies here, so the Complete method can be called transitionally on messages received from the same queue, or messages received from one or more subscriptions in the same topic. Sending Multiple Messages in a Transaction A transactional scope can be used to send multiple messages to a queue or topic. This will ensure that all the messages will be enqueued or, if the transaction fails to commit, no messages will be enqueued.     An example of the code used to send 10 messages to a queue as a single transaction from a console application is shown below.   QueueClient queueClient = messagingFactory.CreateQueueClient(Queue1);   Console.Write("Sending");   // Create a transaction scope. using (TransactionScope scope = new TransactionScope()) {     for (int i = 0; i < 10; i++)     {         // Send a message         BrokeredMessage msg = new BrokeredMessage("Message: " + i);         queueClient.Send(msg);         Console.Write(".");     }     Console.WriteLine("Done!");     Console.WriteLine();       // Should we commit the transaction?     Console.WriteLine("Commit send 10 messages? (yes or no)");     string reply = Console.ReadLine();     if (reply.ToLower().Equals("yes"))     {         // Commit the transaction.         scope.Complete();     } } Console.WriteLine(); messagingFactory.Close();     The transaction scope is used to wrap the sending of 10 messages. Once the messages have been sent the user has the option to either commit the transaction or abandon the transaction. If the user enters “yes”, the Complete method is called on the scope, which will commit the transaction and result in the messages being enqueued. If the user enters anything other than “yes”, the transaction will not commit, and the messages will not be enqueued. Receiving Multiple Messages in a Transaction The receiving of multiple messages is another scenario where the use of transactions can improve reliability. When receiving a group of messages that are related together, maybe in the same message session, it is possible to receive the messages in the peek-lock receive mode, and then complete, defer, or deadletter the messages in one transaction. (In the current version of Service Bus, abandon is not transactional.)   The following code shows how this can be achieved. using (TransactionScope scope = new TransactionScope()) {       while (true)     {         // Receive a message.         BrokeredMessage msg = q1Client.Receive(TimeSpan.FromSeconds(1));         if (msg != null)         {             // Wrote message body and complete message.             string text = msg.GetBody<string>();             Console.WriteLine("Received: " + text);             msg.Complete();         }         else         {             break;         }     }     Console.WriteLine();       // Should we commit?     Console.WriteLine("Commit receive? (yes or no)");     string reply = Console.ReadLine();     if (reply.ToLower().Equals("yes"))     {         // Commit the transaction.         scope.Complete();     }     Console.WriteLine(); }     Note that if there are a large number of messages to be received, there will be a chance that the transaction may time out before it can be committed. It is possible to specify a longer timeout when the transaction is created, but It may be better to receive and commit smaller amounts of messages within the transaction. It is also possible to complete, defer, or deadletter messages received from more than one subscription, as long as all the subscriptions are contained in the same topic. As subscriptions are not top level messaging entities this scenarios will work. The following code shows how this can be achieved. try {     using (TransactionScope scope = new TransactionScope())     {         // Receive one message from each subscription.         BrokeredMessage msg1 = subscriptionClient1.Receive();         BrokeredMessage msg2 = subscriptionClient2.Receive();           // Complete the message receives.         msg1.Complete();         msg2.Complete();           Console.WriteLine("Msg1: " + msg1.GetBody<string>());         Console.WriteLine("Msg2: " + msg2.GetBody<string>());           // Commit the transaction.         scope.Complete();     } } catch (Exception ex) {     Console.WriteLine(ex.Message); }     Unsupported Scenarios The restriction of only one top level messaging entity being able to participate in a transaction makes some useful scenarios unsupported. As the Windows Azure Service Bus is under continuous development and new releases are expected to be frequent it is possible that this restriction may not be present in future releases. The first is the scenario where messages are to be routed to two different systems. The following code attempts to do this.   try {     // Create a transaction scope.     using (TransactionScope scope = new TransactionScope())     {         BrokeredMessage msg1 = new BrokeredMessage("Message1");         BrokeredMessage msg2 = new BrokeredMessage("Message2");           // Send a message to Queue1         Console.WriteLine("Sending Message1");         queue1Client.Send(msg1);           // Send a message to Queue2         Console.WriteLine("Sending Message2");         queue2Client.Send(msg2);           // Commit the transaction.         Console.WriteLine("Committing transaction...");         scope.Complete();     } } catch (Exception ex) {     Console.WriteLine(ex.Message); }     The results of running the code are shown below. When attempting to send a message to the second queue the following exception is thrown: No active Transaction was found for ID '35ad2495-ee8a-4956-bbad-eb4fedf4a96e:1'. The Transaction may have timed out or attempted to span multiple top-level entities such as Queue or Topic. The server Transaction timeout is: 00:01:00..TrackingId:947b8c4b-7754-4044-b91b-4a959c3f9192_3_3,TimeStamp:3/29/2012 7:47:32 AM.   Another scenario where transactional support could be useful is when forwarding messages from one queue to another queue. This would also involve more than one top level messaging entity, and is therefore not supported.   Another scenario that developers may wish to implement is performing transactions across messaging entities and other transactional systems, such as an on-premise database. In the current release this is not supported.   Workarounds for Unsupported Scenarios There are some techniques that developers can use to work around the one top level entity limitation of transactions. When sending two messages to two systems, topics and subscriptions can be used. If the same message is to be sent to two destinations then the subscriptions would have the default subscriptions, and the client would only send one message. If two different messages are to be sent, then filters on the subscriptions can route the messages to the appropriate destination. The client can then send the two messages to the topic in the same transaction.   In scenarios where a message needs to be received and then forwarded to another system within the same transaction topics and subscriptions can also be used. A message can be received from a subscription, and then sent to a topic within the same transaction. As a topic is a top level messaging entity, and a subscription is not, this scenario will work.

    Read the article

  • Oracle Fusion Applications: Changing the Game

    - by kellsey.ruppel(at)oracle.com
    Originally posted in the Oracle Profit Magazine, November 2010 Edition. When the order processing system red-flags a customer's credit status, the IT department doesn't get the customer's call. When a supplier misses a delivery date for a key automotive assembly, it's not the CIO who has to answer for the error. Knowledge workers (known in IT circles as "users") are on the front lines when an exception occurs in an established business process. They're also the ones who study sales trends to decide when to open a new store in an up-and-coming neighborhood, which products are most profitable, how employee skill sets are evolving, and which suppliers are most efficient. In short, knowledge workers are masters of business as unusual. Traditional enterprise resource planning (ERP) systems and other familiar enterprise applications excel at automating, managing, and executing standard business processes. These programs shine when everything goes as planned. Life gets even trickier when a traditional application needs to be extended with a new service or an extra step is added to a business process when new products are brought to market, divisions are merged, or companies are acquired. Monolithic applications often need the IT department to step in and make the necessary adjustments--incurring additional costs and delays. Until now. When Oracle unveiled the much-anticipated family of Oracle Fusion Applications at Oracle OpenWorld in September 2010, knowledge workers in particular had a lot to cheer about. Business users will soon have ready access to analytical information and collaboration tools in the context of what they are working on, so they can make better decisions when problems or opportunities arise. Additionally, the Oracle Fusion Applications platform will make it easy for business users to tweak processes, create new capabilities, and find information, often without the need for IT department assistance and while still following company guidelines. And IT leaders will be happy to hear about new deployment options, guided implementation and setup tools, and cost-saving management capabilities. Just as important, the underlying technologies in Oracle Fusion Applications will allow organizations to choose among their existing investments and next-generation enterprise applications so they can introduce innovations at a pace that makes the most business and financial sense. "Oracle Fusion Applications are architected so you don't have to do rip and replace," says Jim Hayes, managing director of the consulting firm Accenture. "That's very important for creating a business case that will get through the steering committee and be approved by the board. It shows you can drive value and make a difference in the near term." For these and other reasons, analysts and early adopters are calling Oracle Fusion Applications a game changer for enterprise customers. The differences become apparent in three key areas: the way we innovate, work, and adopt technology. Game Changer #1: New Standard for InnovationChange is a constant challenge for most businesses, whether the catalysts are market dynamics, new competition, or the ever-expanding regulatory environment. And, in an ongoing effort to differentiate, business leaders are constantly looking for new ways to do business, serve constituents, and bring new products and services to market. In addition, companies face significant costs to keep their applications up-to-date. For example, when a company adds new suppliers to a procurement system, the IT shop typically has to invest time, effort, and even consulting fees for custom integrations that allow various ERP systems to communicate with each other. Oracle Fusion Applications were built on Web services and a modular SOA foundation to ease customizations and integration activities among all applications--whether from Oracle or another vendor. Interfaces and updates written in ubiquitous Java, rather than a proprietary coding language, allow organizations to tap into existing in-house technical skills rather than seek expensive outside specialists. And with SOA, organizations can extend a feature set or integrate with other SOA environments by combining Web services such as "look up customer" into a new business process managed by the BPEL orchestration engine. Flexibility like this has long-term implications. "Because users capture these changes at a higher metadata layer, not in the application's code, changes and additions are protected even as new versions of Oracle Fusion Applications are released," says Steve Miranda, senior vice president of applications development at Oracle. "This is a much more sustainable approach because you don't incur costly customizations that prevent upgrades and other innovations." And changes are easier to make: if one change is made in the metadata, that change is automatically reflected throughout the application interface, business intelligence, business process, and business logic. Game Changer #2: New Standard for WorkBoosting productivity comes down to doing the basics right: running business processes more efficiently and managing exceptions more effectively, so users can accomplish more in the course of a day or spend more quality time with the most profitable customers. The fastest way to improve process efficiency is to reduce the number of steps it takes to execute common tasks, such as ordering office equipment from an internal procurement system. Oracle Fusion Applications will deliver a complete role-based user experience with business intelligence and collaboration capabilities provided in the context of the work at hand. "We created every Oracle Fusion Applications screen by asking 'What does the user need to know?' 'What does he or she need to do?' and 'Who do they need to work with to get the job done?'" Miranda explains. So when the sales department heads need new laptops, the self-service procurement screen will not only display a list of approved vendors and configurations, but also a running list of reviews by coworkers who recently purchased the various models. Embedded intelligence may also display prevailing delivery lead times based on actual order histories, not the generic shipping dates vendors may quote. The pervasive business intelligence serves many other business activities across all areas of the enterprise. For example, a manager considering whether to promote a direct report can see the person's employee profile, with a salary history, appraisal summaries, and a rundown of skills and training. This approach to business intelligence also has implications for supply chain management. "One of the challenges at Ingersoll Rand is lack of visibility in our supply chain," says Mike Macrie, global director of enterprise applications for global industrial firm Ingersoll Rand. "Oracle Fusion Applications are going to provide the embedded intelligence to give us that visibility and give us the ability to analyze those orders at any point in our supply chain." Oracle Fusion Applications will also create a "role-based user experience" that displays a work list of events that need attention, based on user job function. Role awareness guides users with daily lists of action items and exceptions. So a credit manager may see seven invoices with discounts that are about to expire or 12 suppliers that have been put on hold because credit memos are awaiting approval. Individualization extends to the search capabilities of Oracle Fusion Applications. The platform uses Web-style search screens powered by an Oracle enterprise search engine, with a security framework that filters search results so individuals will only see the internal information they're authorized to access. A further aid to productivity is Oracle Fusion Applications' integration with Web 2.0 collaboration and social networking resources for business environments. Hover-over text will reveal relevant contact information whenever the name of a person appears in an Oracle Fusion Application. Users can connect via an online chat, phone call, or instant message without leaving the main application, reducing the time required for an accounts payable staffer to resolve a mismatch between an invoiced charge and the service record, for example. Addresses of suppliers, customers, or partners will also initiate hover-over text to show contact details and Web-based maps. Finally, Oracle Fusion Applications will promote a new way of working with purpose-driven communities that can bring new efficiencies to everything from cultivating sales leads to managing new projects. As soon as a lead or project materializes, the applications will automatically gather relevant participants into an online community that shares member contact information, schedules, discussion forums, and Wiki pages. "Oracle Fusion Applications will allow us to take it to the next level with embedded Web 2.0 tools and the embedded analytics," says Steve Printz, CIO and vice president, supply chain management, at window-and-door manufacturer Pella. "[This] allows those employees today who are processing transactions to really contribute to the success of the company and become decision-makers." Game Changer #3: New Standard for Technology AdoptionAs IT becomes a dominant component of how businesses run and compete, organizations need to lower the cost of implementing applications and introducing new application features. In the past, rolling out new code often required creating a test bed system, moving beta code to a separate system for user feedback, and--once all the revisions were made--moving version one of the software onto production systems, where business users could finally get the needed new features. Oracle Fusion Applications will use a dedicated setup manager application to streamline this process. First, the setup manager will help scope out the project, querying users about their requirements. "From those questions and answers we determine the steps and the order of those steps that will enable that task," Miranda says. Next, system utilities will assign tasks to owners, track completion status, and monitor the overall status of a programming effort. Oracle Fusion Applications can then recommend Web services that allow users to migrate setup choices and steps across all the various deployments of the application. Those setup capabilities automate the migration from test systems to production systems, as well as between different business units that may be using the same application. "The self-service ability of the setup manager helps business users change setups with very little intervention from the IT team," says Ravi Kumar, vice president at IT services company Infosys. "That to me is a big difference from how we've viewed enterprise applications before." For additional flexibility, organizations will be able to adopt Oracle Fusion Applications modules in either of two modes: a single-instance alternative uses one database for all Oracle Fusion Applications, while a "pillar mode" creates separate databases to underpin each application. This means IT departments running any one of Oracle's applications or even third-party applications can plug Oracle Fusion Applications modules into their environment and see additional business value created on top of their existing systems. And Oracle Fusion Applications offer a hybrid approach to deployment. The applications are all software-as-a-service-ready, so customers can choose on-premises, public or private cloud, or a combination of these to suit their business needs. It's that combination of flexibility and a roadmap for the future that may be the biggest game changer of all. "The Oracle Fusion Applications architecture allows us to migrate our company at a pace that's consistent with our business strategy, whereas before we might have had to do it with a massive upgrade," says Macrie of Ingersoll Rand. "We're looking forward to that architecture to really give us more flexibility in how we migrate over time." For More InformationUser Input Key to the Success of Oracle Fusion ApplicationsTransforming Coexistence into Strategic ValueUnder the HoodOracle Fusion ApplicationsOracle Service-Oriented Architecture  

    Read the article

  • Michael Crump&rsquo;s notes for 70-563 PRO &ndash; Designing and Developing Windows Applications usi

    - by mbcrump
    TIME TO GO PRO! This is my notes for 70-563 PRO – Designing and Developing Windows Applications using .NET Framework 3.5 I created it using several resources (various certification web sites, msdn, official ms 70-548 book). The reason that I created this review is because a) I am taking the exam. b) MS did not create a book for this exam. Use the(MS 70-548)book. c) To make sure I am familiar with each before the exam. I hope that it provides a good start for your own notes. I hope that someone finds this useful. At least, it will give you a starting point of what to expect to know on the PRO exam. Also, for those wondering, the PRO exam does contains very little code. It is basically all theory. 1. Validation Controls – How to prevent users from entering invalid data on forms. (MaskedTextBox control and RegEx) 2. ServiceController – used to start and control the behavior of existing services. 3. User Feedback (know winforms Status Bar, Tool Tips, Color, Error Provider, Context-Sensitive and Accessibility) 4. Specific (derived) exceptions must be handled before general (base class) exceptions. By moving the exception handling for the base type Exception to after exception handling of ArgumentNullException, all ArgumentNullException thrown by the Helper method will be caught and logged correctly. 5. A heartbeat method is a method exposed by a Web service that allows external applications to check on the status of the service. 6. New users must master key tasks quickly. Giving these tasks context and appropriate detail will help. However, advanced users will demand quicker paths. Shortcuts, accelerators, or toolbar buttons will speed things along for the advanced user. 7. MSBuild uses project files to instruct the build engine what to build and how to build it. MSBuild project files are XML files that adhere to the MSBuild XML schema. The MSBuild project files contain complete file, build action, and dependency information for each individual projects. 8. Evaluating whether or not to fix a bug involves a triage process. You must identify the bug's impact, set the priority, categorize it, and assign a developer. Many times the person doing the triage work will assign the bug to a developer for further investigation. In fact, the workflow for the bug work item inside of Team System supports this step. Developers are often asked to assess the impact of a given bug. This assessment helps the person doing the triage make a decision on how to proceed. When assessing the impact of a bug, you should consider time and resources to fix it, bug risk, and impacts of the bug. 9. In large projects it is generally impossible and unfeasible to fix all bugs because of the impact on schedule and budget. 10. Code reviews should be conducted by a technical lead or a technical peer. 11. Testing Applications 12. WCF Services – application state 13. SQL Server 2005 / 2008 Express Edition – reliable storage of data / Microsoft SQL Server 3.5 Compact Database– used for client computers to retrieve and save data from a shared location. 14. SQL Server 2008 Compact Edition – used for minimum possible memory and can synchronize data with a corporate SQL Server 2008 Database. Supports offline user and minimum dependency on external components. 15. MDI and SDI Forms (specifically IsMDIContainer) 16. GUID – in the case of data warehousing, it is important to define unique keys. 17. Encrypting / Security Data 18. Understanding of Isolated Storage/Proper location to store items 19. LINQ to SQL 20. Multithreaded access 21. ADO.NET Entity Framework model 22. Marshal.ReleaseComObject 23. Common User Interface Layout (ComboBox, ListBox, Listview, MaskedTextBox, TextBox, RichTextBox, SplitContainer, TableLayoutPanel, TabControl) 24. DataSets Class - http://msdn.microsoft.com/en-us/library/system.data.dataset%28VS.71%29.aspx 25. SQL Server 2008 Reporting Services (SSRS) 26. SystemIcons.Shield (Vista UAC) 27. Leverging stored procedures to perform data manipulation for a database schema that can change. 28. DataContext 29. Microsoft Windows Installer Packages, ClickOnce(bootstrapping features), XCopy. 30. Client Application Services – will authenticate users by using the same data source as a ASP.NET web application. 31. SQL Server 2008 Caching 32. StringBuilder 33. Accessibility Guidelines for Windows Applications http://msdn.microsoft.com/en-us/library/ms228004.aspx 34. Logging erros 35. Testing performance related issues. 36. Role Based Security, GenericIdentity and GenericPrincipal 37. System.Net.CookieContainer will store session data for webapps (see isolated storage for winforms) 38. .NET CLR Profiler tool will identify objects that cause performance issues. 39. ADO.NET Synchronization (SyncGroup) 40. Globalization - CultureInfo 41. IDisposable Interface- reports on several questions relating to this. 42. Adding timestamps to determine whether data has changed or not. 43. Converting applications to .NET Framework 3.5 44. MicrosoftReportViewer 45. Composite Controls 46. Windows Vista KNOWN folders. 47. Microsoft Sync Framework 48. TypeConverter -Provides a unified way of converting types of values to other types, as well as for accessing standard values and sub properties. http://msdn.microsoft.com/en-us/library/system.componentmodel.typeconverter.aspx 49. Concurrency control mechanisms The main categories of concurrency control mechanisms are: Optimistic - Delay the checking of whether a transaction meets the isolation rules (e.g., serializability and recoverability) until its end, without blocking any of its (read, write) operations, and then abort a transaction, if the desired rules are violated. Pessimistic - Block operations of a transaction, if they may cause violation of the rules. Semi-optimistic - Block operations in some situations, and do not block in other situations, while delaying rules checking to transaction's end, as done with optimistic. 50. AutoResetEvent 51. Microsoft Messaging Queue (MSMQ) 4.0 52. Bulk imports 53. KeyDown event of controls 54. WPF UI components 55. UI process layer 56. GAC (installing, removing and queuing) 57. Use a local database cache to reduce the network bandwidth used by applications. 58. Sound can easily be annoying and distracting to users, so use it judiciously. Always give users the option to turn sound off. Because a user might have sound off, never convey important information through sound alone.

    Read the article

  • SSIS Lookup component tuning tips

    - by jamiet
    Yesterday evening I attended a London meeting of the UK SQL Server User Group at Microsoft’s offices in London Victoria. As usual it was both a fun and informative evening and in particular there seemed to be a few questions arising about tuning the SSIS Lookup component; I rattled off some comments and figured it would be prudent to drop some of them into a dedicated blog post, hence the one you are reading right now. Scene setting A popular pattern in SSIS is to use a Lookup component to determine whether a record in the pipeline already exists in the intended destination table or not and I cover this pattern in my 2006 blog post Checking if a row exists and if it does, has it changed? (note to self: must rewrite that blog post for SSIS2008). Fundamentally the SSIS lookup component (when using FullCache option) sucks some data out of a database and holds it in memory so that it can be compared to data in the pipeline. One of the big benefits of using SSIS dataflows is that they process data one buffer at a time; that means that not all of the data from your source exists in the dataflow at the same time and is why a SSIS dataflow can process data volumes that far exceed the available memory. However, that only applies to data in the pipeline; for reasons that are hopefully obvious ALL of the data in the lookup set must exist in the memory cache for the duration of the dataflow’s execution which means that any memory used by the lookup cache will not be available to be used as a pipeline buffer. Moreover, there’s an obvious correlation between the amount of data in the lookup cache and the time it takes to charge that cache; the more data you have then the longer it will take to charge and the longer you have to wait until the dataflow actually starts to do anything. For these reasons your goal is simple: ensure that the lookup cache contains as little data as possible. General tips Here is a simple tick list you can follow in order to tune your lookups: Use a SQL statement to charge your cache, don’t just pick a table from the dropdown list made available to you. (Read why in SELECT *... or select from a dropdown in an OLE DB Source component?) Only pick the columns that you need, ignore everything else Make the database columns that your cache is populated from as narrow as possible. If a column is defined as VARCHAR(20) then SSIS will allocate 20 bytes for every value in that column – that is a big waste if the actual values are significantly less than 20 characters in length. Do you need DT_WSTR typed columns or will DT_STR suffice? DT_WSTR uses twice the amount of space to hold values that can be stored using a DT_STR so if you can use DT_STR, consider doing so. Same principle goes for the numerical datatypes DT_I2/DT_I4/DT_I8. Only populate the cache with data that you KNOW you will need. In other words, think about your WHERE clause! Thinking outside the box It is tempting to build a large monolithic dataflow that does many things, one of which is a Lookup. Often though you can make better use of your available resources by, well, mixing things up a little and here are a few ideas to get your creative juices flowing: There is no rule that says everything has to happen in a single dataflow. If you have some particularly resource intensive lookups then consider putting that lookup into a dataflow all of its own and using raw files to pass the pipeline data in and out of that dataflow. Know your data. If you think, for example, that the majority of your incoming rows will match with only a small subset of your lookup data then consider chaining multiple lookup components together; the first would use a FullCache containing that data subset and the remaining data that doesn’t find a match could be passed to a second lookup that perhaps uses a NoCache lookup thus negating the need to pull all of that least-used lookup data into memory. Do you need to process all of your incoming data all at once? If you can process different partitions of your data separately then you can partition your lookup cache as well. For example, if you are using a lookup to convert a location into a [LocationId] then why not process your data one region at a time? This will mean your lookup cache only has to contain data for the location that you are currently processing and with the ability of the Lookup in SSIS2008 and beyond to charge the cache using a dynamically built SQL statement you’ll be able to achieve it using the same dataflow and simply loop over it using a ForEach loop. Taking the previous data partitioning idea further … a dataflow can contain more than one data path so why not split your data using a conditional split component and, again, charge your lookup caches with only the data that they need for that partition. Lookups have two uses: to (1) find a matching row from the lookup set and (2) put attributes from that matching row into the pipeline. Ask yourself, do you need to do these two things at the same time? After all once you have the key column(s) from your lookup set then you can use that key to get the rest of attributes further downstream, perhaps even in another dataflow. Are you using the same lookup data set multiple times? If so, consider the file caching option in SSIS 2008 and beyond. Above all, experiment and be creative with different combinations. You may be surprised at what works. Final  thoughts If you want to know more about how the Lookup component differs in SSIS2008 from SSIS2005 then I have a dedicated blog post about that at Lookup component gets a makeover. I am on a mini-crusade at the moment to get a BULK MERGE feature into the database engine, the thinking being that if the database engine can quickly merge massive amounts of data in a similar manner to how it can insert massive amounts using BULK INSERT then that’s a lot of work that wouldn’t have to be done in the SSIS pipeline. If you think that is a good idea then go and vote for BULK MERGE on Connect. If you have any other tips to share then please stick them in the comments. Hope this helps! @Jamiet Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

    Read the article

  • CentOS 5.4 NFS v4 client file permissions differ from original files & NFS Share file contents

    - by p4guru
    Having a strange problem with NFS share and file permissions on the 1 out of the 2 NFS clients, web1 has file permissions issues but web2 is fine. web1 and web2 are load balanced web servers. So questions are: how do I ensure NFS share file contents retain the same permissions for user/group as the original files on web1 server like they do on web2 server ? how do I reverse what I did on web1, i tried unmount command and said command not found ? Information: I'm using 3 dedicated server setup. All 3 servers CentOS 5.4 64bit based. servers are as follows: web1 - nfs client with file permissions issues web2 - nfs client file permissions are OKAY db1 - nfs share at /nfsroot web2 nfs client was setup by my web host, while web1 was setup by me. I did the following commands on web1 and it worked with updating db1 nfsroot share at /nfsroot/site_css with latest files on web1 but the file permissions don't stick even if i use tar with -p command to perserve file permissions ? cd /home/username/public_html/forums/script/ tar -zcp site_css/ > site_css.tar.gz mount -t nfs4 nfsshareipaddress:/site_css /home/username/public_html/forums/scripts/site_css/ -o rw,soft cd /home/username/public_html/forums/script/ tar -zxf site_css.tar.gz But checking on web1 file permissions no longer username user/group but owned by nobody ? but web2 file permissions correct ? This is only a problem for web1 while web2 is correct ? Looks like numeric ids aren't the same ? Not sure how to correct this ? web1 with incorrect user/group of nobody ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 nobody nobody 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Feb 22 02:43 ../ -rw-r--r-- 1 nobody nobody 1 Nov 30 2006 index.html -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-cc2f96c9-00011.css web1 numeric ids ls -n /home/username/public_html/forums/scripts/site_css total 48 drwxrwxrwx 2 99 99 4096 Feb 22 02:37 ./ drwxr-xr-x 3 503 500 4096 Feb 22 02:43 ../ -rw-r--r-- 1 99 99 1 Nov 30 2006 index.html -rw-r--r-- 1 99 99 5876 Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 99 99 5877 Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 99 99 5877 Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 99 99 5876 Feb 18 05:37 style-cc2f96c9-00011.css web2 correct username user/group permissions ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Dec 2 14:51 ../ -rw-r--r-- 1 username username 1 Nov 30 2006 index.html -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-cc2f96c9-00011.css web2 numeric ids ls -n /home/username/public_html/forums/scripts/site_css total 48 drwxrwxrwx 2 503 500 4096 Feb 22 02:37 ./ drwxr-xr-x 3 503 500 4096 Dec 2 14:51 ../ -rw-r--r-- 1 503 500 1 Nov 30 2006 index.html -rw-r--r-- 1 503 500 5876 Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 503 500 5877 Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 503 500 5877 Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 503 500 5876 Feb 18 05:37 style-cc2f96c9-00011.css I checked db1 /nfsroot/site_css and user/group ownership was incorrect for newer files dated feb22 owned by root and not username ? on db1 originally incorrect root assigned user/group for new feb22 dated files ls -alh /nfsroot/site_css total 44K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 . drwxr-xr-x 17 root root 4.0K Feb 17 12:06 .. -rw-r--r-- 1 root root 1 Nov 30 2006 index.html -rw-r--r-- 1 root root 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 root root 5.8K Feb 22 02:37 style-95001864-00002.css -rw------- 1 username nfs 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw------- 1 username nfs 5.8K Feb 18 05:37 style-cc2f96c9-00011.css Then I chmod them all on db1 and chown to set to right ownership on db1 so it looks like below on db1 once corrected the newer feb22 dated files ls -alh /nfsroot/site_css total 44K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 . drwxr-xr-x 17 root root 4.0K Feb 17 12:06 .. -rw-r--r-- 1 username username 1 Nov 30 2006 index.html -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-cc2f96c9-00011.css but still web1 shows owned by nobody ? while web2 shows correct permissions ? web1 still with incorrect user/group of nobody not matching what web2 and db1 are set to ? ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 nobody nobody 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Feb 22 02:43 ../ -rw-r--r-- 1 nobody nobody 1 Nov 30 2006 index.html -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-cc2f96c9-00011.css Just so confusing so any help is very very much appreciated! thanks

    Read the article

  • The HTG Guide to Using a Bluetooth Keyboard with Your Android Device

    - by Matt Klein
    Android devices aren’t usually associated with physical keyboards. But, since Google is now bundling their QuickOffice app with the newly-released Kit-Kat, it appears inevitable that at least some Android tablets (particularly 10-inch models) will take on more productivity roles. In recent years, physical keyboards have been rendered obsolete by swipe style input methods such as Swype and Google Keyboard. Physical keyboards tend to make phones thick and plump, and that won’t fly today when thin (and even flexible and curved) is in vogue. So, you’ll be hard-pressed to find smartphone manufacturers launching new models with physical keyboards, thus rendering sliders to a past chapter in mobile phone evolution. It makes sense to ditch the clunky keyboard phone in favor of a lighter, thinner model. You’re going to carry around in your pocket or purse all day, why have that extra bulk and weight? That said, there is sound logic behind pairing tablets with keyboards. Microsoft continues to plod forward with its Surface models, and while critics continue to lavish praise on the iPad, its functionality is obviously enhanced and extended when you add a physical keyboard. Apple even has an entire page devoted specifically to iPad-compatible keyboards. But an Android tablet and a keyboard? Does such a thing even exist? They do actually. There are docking keyboards and keyboard/case combinations, there’s the Asus Transformer family, Logitech markets a Windows 8 keyboard that speaks “Android”, and these are just to name a few. So we know that keyboard products that are designed to work with Android exist, but what about an everyday Bluetooth keyboard you might use with Windows or OS X? How-To Geek wanted look at how viable it is to use such a keyboard with Android. We conducted some research and examined some lists of Android keyboard shortcuts. Most of what we found was long outdated. Many of the shortcuts don’t even apply anymore, while others just didn’t work. Regardless, after a little experimentation and a dash of customization, it turns out using a keyboard with Android is kind of fun, and who knows, maybe it will catch on. Setting things up Setting up a Bluetooth keyboard with Android is very easy. First, you’ll need a Bluetooth keyboard and of course an Android device, preferably running version 4.1 (Jelly Bean) or higher. For our test, we paired a second-generation Google Nexus 7 running Android 4.3 with a Samsung Series 7 keyboard. In Android, enable Bluetooth if it isn’t already on. We’d like to note that if you don’t normally use Bluetooth accessories and peripherals with your Android device (or any device really), it’s best practice to leave Bluetooth off because, like GPS, it drains the device’s battery more quickly. To enable Bluetooth, simply go to “Settings” -> “Bluetooth” and tap the slider button to “On”. To set up the keyboard, make sure it is on and then tap “Bluetooth” in the Android settings. On the resulting screen, your Android device should automatically search for and hopefully find your keyboard. If you don’t get it right the first time, simply turn the keyboard on again and then tap “Search for Devices” to try again. If it still doesn’t work, make sure you have fresh batteries and the keyboard isn’t paired to another device. If it is, you will need to unpair it before it will work with your Android device (consult your keyboard manufacturer’s documentation or Google if you don’t know how to do this). When Android finds your keyboard, select it under “Available Devices” … … and you should be prompted to type in a code: If successful, you will see that device is now “Connected” and you’re ready to go. If you want to test things out, try pressing the “Windows” key (“Apple” or “Command”) + ESC, and you will be whisked to your Home screen. So, what can you do? Traditional Mac and Windows users know there’s usually a keyboard shortcut for just about everything (and if there isn’t, there’s all kinds of ways to remap keys to do a variety of commands, tasks, and functions). So where does Android fall in terms of baked-in keyboard commands? There answer to that is kind of enough, but not too much. There are definitely established combos you can use to get around, but they aren’t clear and there doesn’t appear to be any one authority on what they are. Still, there is enough keyboard functionality in Android to make it a viable option, if only for those times when you need to get something done (long e-mail or important document) and an on-screen keyboard simply won’t do. It’s important to remember that Android is, and likely always will be a touch-first interface. That said, it does make some concessions to physical keyboards. In other words, you can get around Android fairly well without having to lift your hands off the keys, but you will still have to tap the screen regularly, unless you add a mouse. For example, you can wake your device by tapping a key rather than pressing its power button. However, if your device is slide or pattern-locked, then you’ll have to use the touchscreen to unlock it – a password or PIN however, works seamlessly with a keyboard – other things like widgets and app controls and features, have to be tapped. You get the idea. Keyboard shortcuts and navigation As we said, baked-in keyboard shortcut combos aren’t necessarily abundant nor apparent. The one thing you can always do is search. Any time you want to Google something, start typing from the Home screen and the search screen will automatically open and begin displaying results. Other than that, here is what we were able to figure out: ESC = go back CTRL + ESC = menu CTRL + ALT + DEL = restart (no questions asked) ALT + SPACE = search page (say “OK Google” to voice search) ALT + TAB (ALT + SHIFT + TAB) = switch tasks Also, if you have designated volume function keys, those will probably work too. There’s also some dedicated app shortcuts like calculator, Gmail, and a few others: CMD + A = calculator CMD + C = contacts CMD + E = e-mail CMD + G = Gmail CMD + L = Calendar CMD + P = Play Music CMD + Y = YouTube Overall, it’s not a long comprehensive list and there’s no dedicated keyboard combos for the full array of Google’s products. Granted, it’s hard to imagine getting a lot of mileage out of a keyboard with Maps but with something like Keep, you could type out long, detailed lists on your tablet, and then view them on your smartphone when you go out shopping. You can also use the arrow keys to navigate your Home screen over shortcuts and open the app drawer. When something on the screen is selected, it will be highlighted in blue. Press “Enter” to open your selection. Additionally, if an app has its own set of shortcuts, e.g. Gmail has quite a few unique shortcuts to it, as does Chrome, some – though not many – will work in Android (not for YouTube though). Also, many “universal” shortcuts such as Copy (CTRL + C), Cut (CTRL + X), Paste (CTRL + V), and Select All (CTRL + A) work where needed – such as in instant messaging, e-mail, social media apps, etc. Creating custom application shortcuts What about custom shortcuts? When we were researching this article, we were under the impression that it was possible to assign keyboard combinations to specific apps, such as you could do on older Android versions such as Gingerbread. This no long seems to be the case and nowhere in “Settings” could we find a way to assign hotkey combos to any of our favorite, oft-used apps or functions. If you do want custom keyboard shortcuts, what can you do? Luckily, there’s an app on Google Play that allows you to, among other things, create custom app shortcuts. It is called External Keyboard Helper (EKH) and while there is a free demo version, the pay version is only a few bucks. We decided to give EKH a whirl and through a little experimentation and finally reading the developer’s how-to, we found we could map custom keyboard combos to just about anything. To do this, first open the application and you’ll see the main app screen. Don’t worry about choosing a custom layout or anything like that, you want to go straight to the “Advanced settings”: In the “Advanced settings” select “Application shortcuts” to continue: You can have up to 16 custom application shortcuts. We are going to create a custom shortcut to the Facebook app. We choose “A0”, and from the resulting list, Facebook. You can do this for any number of apps, services, and settings. As you can now see, the Facebook app has now been linked to application-zero (A0): Go back to the “Advanced settings” and choose “Customize keyboard mappings”: You will be prompted to create a custom keyboard layout so we choose “Custom 1”: When you choose to create a custom layout, you can do a great many more things with your keyboard. For example, many keyboards have predefined function (Fn) keys, which you can map to your tablet’s brightness controls, toggle WiFi on/off, and much more. A word of advice, the application automatically remaps certain keys when you create a custom layout. This might mess up some existing keyboard combos. If you simply want to add some functionality to your keyboard, you can go ahead and delete EKH’s default changes and start your custom layout from scratch. To create a new combo, select “Add new key mapping”: For our new shortcut, we are going to assign the Facebook app to open when we key in “ALT + F”. To do this, we press the “F” key while in the “Scancode” field and we see it returns a value of “33”. If we wanted to use a different key, we can press “Change” and scan another key’s numerical value. We now want to assign the “ALT” key to application “A0”, previously designated as the Facebook app. In the “AltGr” field, we enter “A0” and then “Save” our custom combo. And now we see our new application shortcut. Now, as long as we’re using our custom layout, every time we press “ALT + F”, the Facebook app will launch: External Keyboard Helper extends far beyond simple application shortcuts and if you are looking for deeper keyboard customization options, you should definitely check it out. Among other things, EKH also supports dozens of languages, allows you to quickly switch between layouts using a key or combo, add up to 16 custom text shortcuts, and much more! It can be had on Google Play for $2.53 for the full version, but you can try the demo version for free. More extensive documentation on how to use the app is also available. Android? Keyboard? Sure, why not? Unlike traditional desktop operating systems, you don’t need a physical keyboard and mouse to use a mobile operating system. You can buy an iPad or Nexus 10 or Galaxy Note, and never need another accessory or peripheral – they work as intended right out of the box. It’s even possible you can write the next great American novel on one these devices, though that might require a lot of practice and patience. That said, using a keyboard with Android is kind of fun. It’s not revelatory but it does elevate the experience. You don’t even need to add customizations (though they are nice) because there are enough existing keyboard shortcuts in Android to make it usable. Plus, when it comes to inputting text such as in an editor or terminal application, we fully advocate big, physical keyboards. Bottom line, if you’re looking for a way to enhance your Android tablet, give a keyboard a chance. Do you use your Android device for productivity? Is a physical keyboard an important part of your setup? Do you have any shortcuts that we missed? Sound off in the comments and let us know what you think.     

    Read the article

  • SQL SERVER – Guest Posts – Feodor Georgiev – The Context of Our Database Environment – Going Beyond the Internal SQL Server Waits – Wait Type – Day 21 of 28

    - by pinaldave
    This guest post is submitted by Feodor. Feodor Georgiev is a SQL Server database specialist with extensive experience of thinking both within and outside the box. He has wide experience of different systems and solutions in the fields of architecture, scalability, performance, etc. Feodor has experience with SQL Server 2000 and later versions, and is certified in SQL Server 2008. In this article Feodor explains the server-client-server process, and concentrated on the mutual waits between client and SQL Server. This is essential in grasping the concept of waits in a ‘global’ application plan. Recently I was asked to write a blog post about the wait statistics in SQL Server and since I had been thinking about writing it for quite some time now, here it is. It is a wide-spread idea that the wait statistics in SQL Server will tell you everything about your performance. Well, almost. Or should I say – barely. The reason for this is that SQL Server is always a part of a bigger system – there are always other players in the game: whether it is a client application, web service, any other kind of data import/export process and so on. In short, the SQL Server surroundings look like this: This means that SQL Server, aside from its internal waits, also depends on external waits and settings. As we can see in the picture above, SQL Server needs to have an interface in order to communicate with the surrounding clients over the network. For this communication, SQL Server uses protocol interfaces. I will not go into detail about which protocols are best, but you can read this article. Also, review the information about the TDS (Tabular data stream). As we all know, our system is only as fast as its slowest component. This means that when we look at our environment as a whole, the SQL Server might be a victim of external pressure, no matter how well we have tuned our database server performance. Let’s dive into an example: let’s say that we have a web server, hosting a web application which is using data from our SQL Server, hosted on another server. The network card of the web server for some reason is malfunctioning (think of a hardware failure, driver failure, or just improper setup) and does not send/receive data faster than 10Mbs. On the other end, our SQL Server will not be able to send/receive data at a faster rate either. This means that the application users will notify the support team and will say: “My data is coming very slow.” Now, let’s move on to a bit more exciting example: imagine that there is a similar setup as the example above – one web server and one database server, and the application is not using any stored procedure calls, but instead for every user request the application is sending 80kb query over the network to the SQL Server. (I really thought this does not happen in real life until I saw it one day.) So, what happens in this case? To make things worse, let’s say that the 80kb query text is submitted from the application to the SQL Server at least 100 times per minute, and as often as 300 times per minute in peak times. Here is what happens: in order for this query to reach the SQL Server, it will have to be broken into a of number network packets (according to the packet size settings) – and will travel over the network. On the other side, our SQL Server network card will receive the packets, will pass them to our network layer, the packets will get assembled, and eventually SQL Server will start processing the query – parsing, allegorizing, generating the query execution plan and so on. So far, we have already had a serious network overhead by waiting for the packets to reach our Database Engine. There will certainly be some processing overhead – until the database engine deals with the 80kb query and its 20 subqueries. The waits you see in the DMVs are actually collected from the point the query reaches the SQL Server and the packets are assembled. Let’s say that our query is processed and it finally returns 15000 rows. These rows have a certain size as well, depending on the data types returned. This means that the data will have converted to packages (depending on the network size package settings) and will have to reach the application server. There will also be waits, however, this time you will be able to see a wait type in the DMVs called ASYNC_NETWORK_IO. What this wait type indicates is that the client is not consuming the data fast enough and the network buffers are filling up. Recently Pinal Dave posted a blog on Client Statistics. What Client Statistics does is captures the physical flow characteristics of the query between the client(Management Studio, in this case) and the server and back to the client. As you see in the image, there are three categories: Query Profile Statistics, Network Statistics and Time Statistics. Number of server roundtrips–a roundtrip consists of a request sent to the server and a reply from the server to the client. For example, if your query has three select statements, and they are separated by ‘GO’ command, then there will be three different roundtrips. TDS Packets sent from the client – TDS (tabular data stream) is the language which SQL Server speaks, and in order for applications to communicate with SQL Server, they need to pack the requests in TDS packets. TDS Packets sent from the client is the number of packets sent from the client; in case the request is large, then it may need more buffers, and eventually might even need more server roundtrips. TDS packets received from server –is the TDS packets sent by the server to the client during the query execution. Bytes sent from client – is the volume of the data set to our SQL Server, measured in bytes; i.e. how big of a query we have sent to the SQL Server. This is why it is best to use stored procedures, since the reusable code (which already exists as an object in the SQL Server) will only be called as a name of procedure + parameters, and this will minimize the network pressure. Bytes received from server – is the amount of data the SQL Server has sent to the client, measured in bytes. Depending on the number of rows and the datatypes involved, this number will vary. But still, think about the network load when you request data from SQL Server. Client processing time – is the amount of time spent in milliseconds between the first received response packet and the last received response packet by the client. Wait time on server replies – is the time in milliseconds between the last request packet which left the client and the first response packet which came back from the server to the client. Total execution time – is the sum of client processing time and wait time on server replies (the SQL Server internal processing time) Here is an illustration of the Client-server communication model which should help you understand the mutual waits in a client-server environment. Keep in mind that a query with a large ‘wait time on server replies’ means the server took a long time to produce the very first row. This is usual on queries that have operators that need the entire sub-query to evaluate before they proceed (for example, sort and top operators). However, a query with a very short ‘wait time on server replies’ means that the query was able to return the first row fast. However a long ‘client processing time’ does not necessarily imply the client spent a lot of time processing and the server was blocked waiting on the client. It can simply mean that the server continued to return rows from the result and this is how long it took until the very last row was returned. The bottom line is that developers and DBAs should work together and think carefully of the resource utilization in the client-server environment. From experience I can say that so far I have seen only cases when the application developers and the Database developers are on their own and do not ask questions about the other party’s world. I would recommend using the Client Statistics tool during new development to track the performance of the queries, and also to find a synchronous way of utilizing resources between the client – server – client. Here is another example: think about similar setup as above, but add another server to the game. Let’s say that we keep our media on a separate server, and together with the data from our SQL Server we need to display some images on the webpage requested by our user. No matter how simple or complicated the logic to get the images is, if the images are 500kb each our users will get the page slowly and they will still think that there is something wrong with our data. Anyway, I don’t mean to get carried away too far from SQL Server. Instead, what I would like to say is that DBAs should also be aware of ‘the big picture’. I wrote a blog post a while back on this topic, and if you are interested, you can read it here about the big picture. And finally, here are some guidelines for monitoring the network performance and improving it: Run a trace and outline all queries that return more than 1000 rows (in Profiler you can actually filter and sort the captured trace by number of returned rows). This is not a set number; it is more of a guideline. The general thought is that no application user can consume that many rows at once. Ask yourself and your fellow-developers: ‘why?’. Monitor your network counters in Perfmon: Network Interface:Output queue length, Redirector:Network errors/sec, TCPv4: Segments retransmitted/sec and so on. Make sure to establish a good friendship with your network administrator (buy them coffee, for example J ) and get into a conversation about the network settings. Have them explain to you how the network cards are setup – are they standalone, are they ‘teamed’, what are the settings – full duplex and so on. Find some time to read a bit about networking. In this short blog post I hope I have turned your attention to ‘the big picture’ and the fact that there are other factors affecting our SQL Server, aside from its internal workings. As a further reading I would still highly recommend the Wait Stats series on this blog, also I would recommend you have the coffee break conversation with your network admin as soon as possible. This guest post is written by Feodor Georgiev. Read all the post in the Wait Types and Queue series. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, Readers Contribution, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL

    Read the article

< Previous Page | 526 527 528 529 530 531 532 533 534 535 536 537  | Next Page >