Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 531/772 | < Previous Page | 527 528 529 530 531 532 533 534 535 536 537 538  | Next Page >

• Server 2003 and XP Client; Why are HTTP connections being silently dropped.

  - by Asa Yeamans

  On my network, my edge-router, a windows 2003 r2 server router with all the latest updates, will drop packets, but only under specific circumstances. I have troubleshot and isolated it down to the most simple configuration i can. There is NO NAT involved. Only fully-public IP addresses. No Firewalls are running either, all ahve been disabled. no packet filters on any interfaces anywhere either. I have a single Windows XP virtual machine and my edge-router(the windows 2003 r2 server, and also a virtual machine) running on a windows 2008 x64 r2 system (running virtual server 2005 as i dont have Intel-VT compatible chip yet). The edge router can access any external http site just fine, no issues. However the windows XP machine is only able to access certain sites. These work: www.google.com www.txstate.edu www.workintexas.com www.thedailywtf.com . These Dont: www.yahoo.com www.utexas.edu en.wikipedia.org slashdot.org www.bing.com. I have removed all possibility of DNS issues by connecting with net-cat from the XP box and sending GET /\r\nHost: \r\n\r\n and that connection replicates the issue as well. The network setup: My statically assigned IP block: x.x.x.168/29 DSL Modem -----PPPoE Connection---- x.x.x.169[EdgeRouter] [EdgeRouter]x.x.x.170 -----Virtual Ethernet----- x.x.x.174 [Test2] Test2's Default gateway is x.x.x.170 and test2 can ping any and every valid, accessible, public IP address with no packet loss what-so-ever. If i connect directly over PPPoE from test2 (the XP box) everything works just fine... Im at my wits end, i have NO IDEA whats causing this.

  Read the article

• Enable gzip on Nginx

  - by Rob Wilkerson

  Yes, I know that there are a lot of other questions that seem exactly like this out there. I think I must've looked all of them. Twice. In desparation, I'm adding another in case my specific configuration is the issue. Bear with me. First, the question: What do I need to do to get gzip compression to work? I have an Ubuntu 12.04 server installed running nginx 1.1.19. Nginx was installed with the following packages: nginx nginx-common nginx-full The http block of my nginx.conf looks like this: http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "msie6"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } Both PageSpeed and YSlow are reporting that I need to enable compression. I can see that the request headers indicate Accept-Encoding:gzip,deflate,sdch, but the response headers do not have the corollary Content-Encoding header. I've tried various other config values (gzip_vary on, gzip_http_version 1.0, etc.), but no joy. As far as I know, I can only assume that nginx was compiled with compression support, but if there's any way to verify that, I'd love to know. If anyone sees anything I'm missing or can suggest further debugging, please let me know. I'm no sysadmin and I'm new to Nginx so I've exhausted everything I can think of or have read. Thanks.

  Read the article

• Amazon AWS VPN how to open a port?

  - by Victor Piousbox

  I have a VPN with public and private subnets; I am considering only public subnet for now. The node 10.0.0.23, I can ssh into it. Let's say I want to connect to MySQL on the node using its private address: ubuntu@ip-10-0-0-23:/$ mysql -u root -h 10.0.0.23 ERROR 2003 (HY000): Can't connect to MySQL server on '10.0.0.23' (111) ubuntu@ip-10-0-0-23:/$ mysql -u root -h localhost Welcome to the MySQL monitor. Commands end with ; or \g. --- 8< --- snip --- 8< --- mysql> The port 3306 is not reachable if I use the private IP? My security group allows port 3306 inbound from 0.0.0.0/0 AND from 10.0.0.0/24. Outbound, allowed all. The generic setup done by Amazon through their wizard does not work... I add ACL that allows everything for everybody, still does not work. What am I missing?

  Read the article

• Configure Domino to use SMTP routing and hMailServer

  - by Sébastien Lachance

  I have been trying for a couple of days to set up a Domino 8.5 server. Basically, I want everything to be run inside a local network. Right now I can send email to other user in the Domino directory without any mail address. I am pretty new to all this stuff, so maybe the answer will be really obvious. What I need to do is be able to send a mail from somewhere else to a domino user that will be redirected to his account. On the Domino server, I also have hMailServer installed on port 25. I configured Domino to use port 26. I followed those step to get where I am now. -I have set the Fully qualified Internet host name to "preview.notes". -Smtp Listener task changed to Enabled to turn on the Listener so that the server can receive messages routed via SMTP routing -Setting up SMTP routing within the local Internet domain (http://www.h2l.com/help/help85%5Fadmin.nsf/f4b82fbb75e942a6852566ac0037f284/7f9738a49efc4f58852574d500097b01?OpenDocument) -I modified the person to use the [email protected] address. -I'm using the hMailServer (which have the local "preview.local" domain name) to send mail to [email protected]. When sending mail I got an error telling that the DNS is not set up correctly. Is using the Domino Smtp server instead of hMailServer will solve the problem? I can Telnet the Domino Smtp Server.

  Read the article

• Docking Station Sound Doesn't Work on Dell D830 with Windows 7

  - by cisellis

  I have a Dell Latitude D830 laptop that is running Windows 7 Enterprise x64. I connect to a docking station during the day with multiple monitors, a keyboard and a mouse. Everything runs with no problems including most of the docking station ports (usb, monitors, etc.) However, the sound port from the docking station does not work since the upgrade to Windows-7. Even with the laptop plugged in, the sound always comes out of the laptop, not the headphones plugged into the docking station. Here's what I've tried: I've seen other issues like via Google this that seem to be mostly unanswered. I found one or two that referenced using the Vista x64 drivers, especially the Nvidia drivers. I do not have an Nvidia chipset but I've reinstalled the sound drivers and that has not helped. I don't have a support contract and considering the cost is usually high to call Dell, that's not an option. Dell's forums are pretty much a wasteland and I've found no help there. Since this is a docking station I thought I might need to try the SATA or Intel chipset drivers from the dell site instead, however I'm not really sure and I need to work on this laptop in the meantime. I can't really afford the downtime to experiment with random drivers all day in case they turn out to be incompatible (Dell still hasn't added Windows 7 to their support site as far as I can tell). Does anyone have any other ideas? Has anyone had this issue and solved it? If so, how? Thanks in advance for your help.

  Read the article

• Enabled Network Discovery on Server, and now VNC and Squeezebox clients don't work

  - by Mike Hanson

  I've recently setup a Windows Server 2008. It's running an email server, Squeezebox server, MS SQL Server, etc. I'm doing remote maintenance with UltraVNC. I had everything working fine. Then the server needed to access a network share on another machine, and I was prompted to turn on network discovery, which I did. I chose the Home rather than Public option. Since doing that, some things have stopped working, while others are still fine. Shared folders and the the Email services (ports 25 and 110) are still accessible. VNC (port 5900) and Squeezeboxes (port 9000) no longer work. Here's what I've tried to try to solve the problem: Checked the network discovery settings, to see if anything looked strange. Checked the firewall settings, and those ports appear to be open. Also in the firewall settings, the entries for Private domain Network Discovery were all on, but the Domain/Public ones were off. I tried turning those on. In the services, turned on Function Discovery Resource Publication and SSDP Discovery. Any other suggestions?

  Read the article

• Migrate openldap users and groups

  - by user53864

  I have an OpenLDAP server running on one of my ubuntu 8.10 servers. I used command-line only for OpenLdap installation and some basic configurations, everything else I'll configure with the Webmin gui tool. I'm trying to migrate to ubuntu 10.04 and I was able to migrate all other servies, application and databases but not the ldap. I'm an ldap beginner: I have installed OpenLDAP server and client on ubuntu 10.04 server using the link and used the following command to export and import ldap users and groups To export from 8.10 server slapcat > ldap.ldif To import to 10.04 server Stop ldap and slapadd -l ldap.ldif and Start ldap Then I accessed Webmin and checked in Ldap users and groups and I could see all the users and groups of my old ldap server.Whenever I create an ldap user from the webmin(in 8.10 or 10.04) a unix user is also created with the home directory under /home. But the imported users in 10.04 from 8.10 are not present as a unix user(/etc/passwd). How could I make the ldap users available as a unix user, is there any perfect way to export and import?. I also wanted to check the ldap users from the terminal that if password is exported properly but I don't know how to access the ldap users which are not available as unix users. On 8.10, I just use su - ldapuser and it is not working in the 10.04 as unix users are not created for the exported ldap users. If every thing works fine then the CVS works as it is using ldap authentication. Anybody could help me?

  Read the article

• Trying to limit IMAP folders/mailboxes my iPhone/iPad sees

  - by QuantumMechanic

  (Note: I am using dovecot 1.0.10 on Ubuntu 8.04.4 LTS. Yes, I know I need to upgrade before next year :) (Note: The SMTP/IMAP server in question only serves my family, so there's only a very few users. Certainly what I propose below, even it it works, would be a logistical nightmare with any significant number of users). I have noticed (and have confirmed via google) that the iOS mail app is terrible in its handling of IMAP subscriptions, namespaces, etc. For example, my iPhone and iPad will see EVERYTHING (all mailboxes, folders, etc.), whereas clients like Thunderbird, alpine, etc. only see what I tell them to see. This makes it an incredible pain to move mail between mailboxes because I have to scroll through a gazillion things. The mail_location in dovecot.conf is: mail_location = mbox:%h/Mail/:INBOX=/var/mail/%u To get around this, I've been considering doing the following for user foo: Create a dovecot userdb with a foo-ios virtual user in it, whose UID is identical to that of the real (in /etc/passwd) foo user and with a homedir of /home/foo-ios. ln -s /var/mail/foo /var/mail/foo-ios mkdir -p /home/foo-ios/Mail cd /home/foo-ios/Mail ln -s /home/foo/Mail/mailbox-i-want-visible mailbox-i-want-visible Make symlinks for the rest of limited set of mailboxes/folders I want visible to the iOS mail app. chown -R foo:foo /home/foo-ios Change iOS mail app settings to log in as user foo-ios instead of user foo. Will this work or will there be some index/file corruption hell because there will be two sets of indexes (one set living in /home/foo/Mail/.imap and other set living in /home/foo-ios/Mail/.imap) indexing the same underlying mbox files? And I'd be more than happy to hear of a better way to do this with dovecot! (Or to hear that dovecot 2.x works better with iOS devices).

  Read the article

• How to use a home network patch panel?

  - by Torben Gundtofte-Bruun

  I'm planning a home network in a house that's not built yet. One recommendation is to add network sockets in various rooms and have them all end in a central place, where it all connects using a network switch. So far so good. Another recommendation says to not connect everything directly to the switch, but to a patch panel which in turn is connected to the switch. I'm unsure why this is good. Is there any practical advantage of using a patch panel if you're not planning to re-wire things very often? How does a patch panel actually work? Let's say it has 24 ports. Does it have another 24 ports on the backside that go to the switch, or what? Wikipedia isn't helpful on this. Clarification: I am planning to run network cables through conduits inside the walls and terminated with network sockets in the wall (as opposed to having just conduits and long regular network cables that have a normal plug in each end). Going by RedGrittyBrick's answer, a patch panel is nearly unavoidable in that case.

  Read the article

• Apache serving empty gzip with assets produced by Rails Asset Pipeline

  - by PizzaPill

  I followed the steps described on the blogpost The Asset Pipeline, from development to production and tweaked them to my environment. The two important files are: /etc/apache/site-available/example.com <VirtualHost *:80> ServerName example.com ServerAlias www.example.com DocumentRoot "/var/www/sites/example.com/current/public" ErrorLog "/var/log/apache2/example.com-error_log" CustomLog "/var/log/apache2/example.com-access_log" common <Directory "/var/www/sites/example.com/current/public"> Options All AllowOverride All Order allow,deny Allow from all </Directory> <Directory "/var/www/sites/example.com/current/public/assets"> AllowOverride All </Directory> <LocationMatch "^/assets/.*$"> Header unset Last-Modified Header unset ETag FileETag none ExpiresActive On ExpiresDefault "access plus 1 year" </LocationMatch> RewriteEngine On # Remove the www RewriteCond %{HTTP_HOST} ^www.example.com$ [NC] RewriteRule ^(.*)$ http://example.com/$1 [R=301,L] </VirtualHost> /var/www/sites/example.com/shared/assets/.htaccess RewriteEngine on RewriteCond %{HTTP:Accept-Encoding} \b(x-)?gzip\b RewriteCond %{REQUEST_FILENAME}.gz -s RewriteRule ^(.+) $1.gz [L] <FilesMatch \.css\.gz$> ForceType text/css Header set Content-Encoding gzip </FilesMatch> <FilesMatch \.js\.gz$> ForceType text/javascript Header set Content-Encoding gzip </FilesMatch> But apache seems to send empty gzip files because the testsite looses all styles and firebug doesnt find any content for the css files. Altough if I call the assets-path directly I get some gibberish that looks like binary data. If I move the htaccess-file everything is back to normal. How could I find out where/what went wrong or do you have any suggestions what error I made? > apache2 -v System: Server version: Apache/2.2.14 (Ubuntu) Server built: Mar 5 2012 16:42:17 > uname -a Linux node0 2.6.18-028stab094.3 #1 SMP Thu Sep 22 12:47:37 MSD 2011 x86_64 GNU/Linux

  Read the article

• Shared configuration for Eclipse on Debian server

  - by Joris Meys

  I've manually installed the latest Eclipse on our debian server and wanted to configure it so all users share the same configuration. It turned out less obvious than I thought: I don't seem to be able to install packages for all users. If I run it myself, all configuration data is saved under my own home directory. If I run Eclipse using sudo, everything is saved under the root directory but is not accessible for other users when they run Eclipse. I've been browsing the manual of Eclipse and some forums, but apart from a "yes, you can" I couldn't find any information on how that should be done. The biggest problem is installing plugins for all users to be found. Any help is greatly appreciated. Eclipse : 3.6.1 classic, installed using this procedure. Server uname: GNU/Linux * 2.6.26-2-amd64 Server is accessed using Putty, and Gnome desktop through realVNC. Just mentioning it if that is of any importance. Our sysadmin is on "prolonged leave" (working in Spain and never replaced), so I'm stuck without help here. EDIT : -- I asked this question also on StackOverflow as I wasn't certain this is a genuine server-related question. Please feel free to merge both questions at the appropriate place. --

  Read the article

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• Server 2003 PDC DNS not working..Failover server is...

  - by Seth

  In the midst of trying to utilize proc power, i create a fault tolerant DNS server a while ago. Since, Ive been trying to add another controller for exchange. So I thought I would revert back to a single primary DNS for the meantime and now Im balancing on a thread. The server i thought I uninstalled DNS, is still acting as DNS. And now the PDC does not resolve. Can anybody walk me through, Im overwhelmed and cant think straight... Im afraid if anyone restarts their machine they wont have internet. Update Ok so from the beginning. I was configuring Exchange on a new server 2008. How it happened I dont know, but it started to not resolve DNS. (exclamation mark on NIC) even though everything was static. So ultimately I decided to remove the server from the problem, because I noticed DNS was in disarray if I used the DNS IP of the first server. This is when I tested with nslookup on each DNS server. I had uninstalled DNS from the second server, but nslookup was still resolving with that IPaddress, which has me all wound up cause I dont understand. So, since the first DNS server isn't resolving, Im assuming if the second one isnt configured right I'll loose internet. Im just confused and dont know where to start troubleshooting...

  Read the article

• Did chkdsk make it harder to restore files?

  - by neyl

  My friend asked me to try and fix his loaded Sansa Clip + which wasn't playing. After opening it in MSC mode I discovered that the Music directory was empty and total of all files was only a few MB. However Disk properties showed me that it was 7Gb full. I then ran Tools - Error Checking and Windows dutifully informed me that disk was corrupt and I should run again Allowing Windows to Fix Errors. I did that and it told me everything was fixed and that all files were placed in FOUND.000 Dir. FOUND.000 was about 7.5 GB with FILE0000-1546 . CHK. (I am aware of methods like ChkBack to scan and convert to mp3 etc BUT Original filenames and structure needed!) Now I started getting worried that I made things worse! I have plenty of experience with Data Recovery Programs - Recuva, Restore My Files etc. and I was anyhow planning to use them to scan the drive. But NOW after CHKDSK "fixed" the drive maybe it modified critical FAT information vital for data recovery. So I run these programs and 0!!!. No trace of files! I tried a ton of Recovery Programs with same results TILL EaseUS Data Recovery Wizard found all files and I purchased program for $55! My Question In your opinion - did running CHKDSK with automatic fixing of errors make matters worse (i.e. many data recovery progs. didn't find a trace and they would have done if not for chkdsk) or was the filesystem too corrupt anyhow for regular File Recovery Progs.? If I would be a Professional - would I be responsible for running CHKDSK - automatic Fixing. Do you know of a better Data Recovery Program than EaseUs Data Recovery wizard - According to my experience I haven't found better!? Thanks

  Read the article

• Ubuntu 12.04/12.10 can't detect windows or any other partitions(Asus z77 UEFI BIOS)

  - by user971155

  I've recently completed tinkering my new pc(motherboard ASUS z77 with UEFI BIOS) and unfortunately not everything works quite well. After installing windows 7 ultimate on a single primary partition(SATA drive) I decided to allocate one more logical partition for additional needs. When I tried doing it with the manager - it said that it couldn't allocate requested size even though I certainly asked for much less than it was available. I thought that it might have been a windows issue and proceded to installing Ubuntu 12.10 x64. When the graphical interface loaded it showed me a message stating that it can't find any other operating system on the drive. When I used custom partioning option it showed me none of my current partions(including that with windows). However, when I boot with "Try Ubuntu" feature it does find them ! I find it weird though. Here's what the console present me with: ubuntu@ubuntu:~$ sudo os-prober /dev/sda1:Windows 7 (loader):Windows:chain ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00072b98 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 100020223 49906688 7 HPFS/NTFS/exFAT /dev/sda3 100022270 1250263039 575120385 5 Extended /dev/sda4 566669312 1250263039 341796864 83 Linux I also tried creating partitions from disk utility which results in error: , Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=51211402240, size=1923000000, type=0x83 Entering MS-DOS parser (offset=0, size=640135028736) MSDOS_MAGIC found looking at part 0 (offset 1048576, size 104857600, type 0x07) new part entry looking at part 1 (offset 105906176, size 51104448512, type 0x07) new part entry looking at part 2 (offset 51211402240, size 588923274240, type 0x05) Entering MS-DOS extended parser (offset=51211402240, size=588923274240) readfrom = 51211402240 MSDOS_MAGIC found Exiting MS-DOS extended parser looking at part 3 (offset 290134687744, size 349999988736, type 0x83) new part entry Exiting MS-DOS parser MSDOS partition table detected containing partition table scheme = 1 got it Error: Can't have overlapping partitions. ped_disk_new() failed Here's what I get when I try to install the system i.stack.imgur.com/pjlb9.png, i.stack.imgur.com/g1lXN.png P.S. It's strange that I even can't create any more partitions neither with disk-utility nor with windows 7 native tools

  Read the article

• How do you make Google's interface always be in your chosen language?

  - by Michael Wolf

  Google's interface and search results don't always appear in my preferred language, English. I'm located in Mexico City and, although I generally have no problem with Spanish, I would prefer search results in English most of the time. (The exception is when I'm using search terms in Spanish.) I'd also prefer the interface to be in English, but that's far less important to me than search results. Google looks at your IP to decide where you're coming from and thus what language to present results in. So, when I type www.google.com into the URL bar, it redirects me to www.google.com.mx. Is there a way to force Google to use one language all the time? Here are some things I've done and tried: 0) I have a Google account, and I've configured it such that it should know that English is my preferred language. I don't often explicitly log out of Google, so generally Google knows I'm me and my preferences when I access its services. 1) I've configured my browser to ask for pages in English. Very few sites support this feature at all; Google isn't one of them. 2) From www.google.com.mx, I can click on "Google.com in English". This works until, I think, I close the browser. 2a) From www.google.com.mx, I can go into account configuration, which is English. From then on, everything's in English. 3) I can append &hl=en (Human Language = English) to the end of the URLs of result pages. 2, 2a, and 3 all "work", but they're all mildly annoying. I'd rather avoid them if I could. (At the risk of stating the obvious, English and Spanish are the languages I'm dealing with, but I imagine that, say, a francophone using Google from Korea would run into basically the same issue.)

  Read the article

• Exchange 2003 ActiveSync problem with certificate

  - by colemanm

  We're having problems getting iPhones to sync properly with SBS 2003 Exchange. When you add a new Exchange ActiveSync account on an iPhone and enter all the pertinent information, it shows a "Verifying Exchange account info" message for a minute or so, then says everything's verified and asks what you want to sync, Mail, Contacts, Calendars... so it looks like it's working. However, when you go to the Mail app and select the Exchange email account, it just shows an "Inbox" folder with nothing in it. When you try refreshing, it attempts for a second, then says "Last Updated" with a timestamp, as if it worked, but there's no mail and no error message/feedback at all. I think I've narrowed it down to some sort of certificate issue, but I'm having trouble finding out where to go from here... I ran MS's Exchange connectivity testing tool with these results: Our cert was purchased from Network Solutions, and I'd already added it to the IIS Default Website for OWA purposes. But this report makes it look like the cert is somehow problematic. I don't know what to do now... Here's a shot of the cert details, just in case:

  Read the article

• Screen Flicker on a black MacBook

  - by sixtyfootersdude

  I have a MacBook Black. For about the last six months I have had a strange screen flicker when I: start my machine and plug in the power cord of my machine This morning when I woke up my computer the screen backlight did not turn on at all. When I held the computer in direct sunlight I could see the screen and I could tell that everything was working normally (other than the backlight). Pressing the screen brightness controls (F2) brought up the brightness panel. The brightness panel informed me that the screen was at maximum brightness. I did a bit of Searching and this is what I found: This post describes how to buy and replace a macbook screen. Do you think that this would solve my problem? Additional info: I am running 10.6.4 I recently upgraded from 10.4. I experienced similar issues in 10.4. I am pretty sure that this is a hardware issue. The problem does not occur when the screen is at a specific angle. It usually only happens at startup/wakeup or when the power is plugged/unplugged.

  Read the article

• ORA- 01157 / Cant connect to database

  - by Tom

  Hi everyone, this is a follow up from this question. Let me start by saying that i am NOT a DBA, so i'm really really lost with this. A few weeks ago, we lost contact with one of our SID'S. All the other services are working, but this one in particular is not. What we got was this message when trying to connect ORA-01033: ORACLE initialization or shutdown in progress An attempt to alter database open ended up in ORA-01157: cannot identify/lock data file 6 - see DBWR trace file ORA-01110: data file 6: '/u01/app/oracle/oradata/xxx/xxx_data.dbf' I tried to shutdown / restart the database, but got this message. Total System Global Area 566231040 bytes Fixed Size 1220604 bytes Variable Size 117440516 bytes Database Buffers 444596224 bytes Redo Buffers 2973696 bytes Database mounted. ORA-01157: cannot identify/lock data file 6 - see DBWR trace file ORA-01110: data file 6: '/u01/app/oracle/oradata/xxx/xxx_data.dbf' When all continued the same, I erased the dbf files (rm xxx_data.dbf xxx_index.dbf), and recreated them using touch xxx_data.dbf. I also tried to recreate the tablespaces using `CREATE TABLESPACE DATA DATAFILE XXX_DATA.DBF` and got Database not open As I said, i don't know how bad this is, or how far i'm from gaining access to my database (well, to this SID at least, the others are working). I would imagine that a last resource would be to throw everything away, and recreating it, but I don't know how to, and I was hoping there's a less destructive solution. Any help will be greatly appreciated . Thanks in advance.

  Read the article

• How to test/debug bad network wiring?

  - by Jack Lloyd

  I recently bought a place already wired with Cat 5E (8 ports, leading to a central closet). However attempting to get link, nothing works. On closer examination, it was obvious that the ends in the closet were wired backwards (brown on pin 1, etc). The jacks that I've pulled out of the wall do look to be correctly done. However, testing with a network cable tester shows zero link between any of the jacks and any of the ports in the closet - I had expected to just see a 1/8, 2/7, ... 8/1 mismatch, but instead get nothing at all. The runs are accessible and look neat, though they take some bends that seem quite sharp and are in some cases much longer than they need to be (the person who put this in was a professional electrician but I suspect this was the first time he ran network cabling). My best guess at this point is that he either bought bad cable, or put so much tension on it that he snapped wires. Though it seems surprising/unlikely that I wouldn't get at least one active wire on one of the 8 lines. So, my question: is there anything else I should try or test before I go ripping out everything and running new cable?

  Read the article

• What is the main reason of adsl modem/routers dying ?

  - by ldigas

  The other day my home adsl modem/router (dwg 684t in this case) died. A guy from the telecom company came, brought another so no problem in day to day operation, but he also left this one. Now, I'm interested ... it didn't fall, it wasn't electrocuted ... but it just doesn't work. What could be the problem ? Can they be fixed ? Is it worth it (in which case I would have two which is always nice) ... What are the usual problems that occur with them ? In this case, I can connect to the router, I can see its settings, I just can't connect to the internet. With the new one everything works. Weird. Edit: Additional question: Can those things be fixed ? I mean, is it worth giving it to a local tinker for him to experiment on it ? I'm not looking for a definite opinion, just your personal advice ... (although in the end I think I'm gonna archive it in the "cylinder register")

  Read the article

• Internet Sharing on Lion breaks my routing table

  - by seaders

  When in the office, I'm connected to a 192.168.1.0/24 network. When Internet Sharing is off, when I run netstat -nr the first entry shows default 192.168.1.254 UGSc 10 62 en0 If I turn Internet sharing on, it shows default link#5 UCS 2 0 en1 This is obviously incorrect and breaks all connectivity of my machine. en1 is my wireless, whereas en0 is my ethernet. If I then disable Internet Sharing, it even deletes that incorrect route, so I'm left with no default route at all. Currently I have one script that I run when I share, or after, when I disable that does route delete default route add default 192.168.1.254 That fixes everything, but I'd love to know what's actually making this happen and how to properly fix it. And just to say that at some point a few months ago, this was working absolutely perfectly, with no hitches, then one day when I brought the laptop home, I couldn't disable the internet sharing, so I couldn't connect to my home wifi. I eventually had to restart the machine and since then this problem has been happening. Any help would be greatly appreciated, thank you.

  Read the article

• Most cost efficient way to backup Subversion data to S3?

  - by sludge

  I'm looking at using S3 as an offsite backup repo for my Subversion database. When I dump my SVN database, it's about 10 gigabytes. I would like to avoid the charge of uploading that data repeatedly. The anatomy of this large file such that new changes to Subversion modify the tail of the file, with everything else staying the same. Because Amazon S3 does not allow you to "patch" files with changes, I will have to upload ten gigs every time I instantiate a backup after doing a simple submit to Subversion. Here are the options as I see them: Option 1 I am looking at duplicity which has --volsize which splits data over an amount of megs. Is it possible to split the Subversion dumps using this so further incremental backups are measured in megabytes? Option 2 Can I just backup the hot subversion repository? This seems like a bad idea if it is in the middle of writing a submit. However, I have the option of taking the repo offline between the hours of midnight and 4am. Each revision in my Berkeley DB uses a file as its record.

  Read the article

• mysql thread count

  - by Ryan M.

  We have a web application that uses apache and mysql. Generally (according to Munin) our MySQL thread count sits between 2 and 4 at all times. The other day, our server almost came to a halt. HTTP requests were slow or wouldn't go through at all, SSH would work, but would take 30+ seconds to register keystrokes, etc.. So we pull up Munin and the only thing that's out of normal boundaries is the Mysql thread count. CPU usage was under 1%, load was under 1.0, plenty of available RAM. As mentioned before, the thread count floats around 2 to 4. At the time of our slow downs it had spiked to 14. So I start poking around the Internet and I see that in most cases, you'll start to see a higher thread count when you start running into slow queries. If I understand it correctly, the request comes in that takes a while to process, in the mean time other requests are coming in, so a new thread will be created to work on the request (yes?). But at the time of the slow down, we had 0 slow queries. My question is: What else can cause mysql to create additional threads. And would this sudden spike in threads possibly cause the server to slow down? To fix the issue, we restarted apache and everything went back to it's beautiful, normal self. Considering the the Server Vitals (CPU, RAM, Network, etc) were all ideal, and the thread count was the only thing out of place, this seems like the most logical thing to pursue as the possible cause. If it matters, we're on Mysql 5.1.40. Server is FreeBSD 7.2 and the server in question is inside a jail.

  Read the article

• xauth, ssh and missing home directory

  - by flolo

  We have several servers, and normaly everything works fine, except now... we get a new aircondition installed. This takes 36 hours and for this time almost all servers got shutdown, only 2 remaining servers run for the most important tasks (i.e. accepting incoming email, delivering some important websites, login-server). Everybody was informed that when they need appropiate data from the homedirs they should fetch it before take down. Long story short: Someone realized that he have run a certain program on one of the servers. No Problem, he can remote login into our login server and run the programm there without home directory (binaries are local and necessary information can be copied to the /tmp). That works like a charm until... ... the user needs to run a GUI programm. I find no easy way to make it running, usually ssh -Y honk@loginserver is enough but now the homedirectory is missing and ssh is not able to copy the cookies into ~/.Xauthority (as the file server with the home directories is down). Paranoid as all systemadmins all X-Server just listen locally not on tcp ports, so no remote X connection possible SSH config is waterproof - i.e. no way to set environment variables. My Problem is, that the generated proxy MIT cookie from ssh get lost as the .Xauthority doesnt exist. If I could retrieve it somehow I could reenter it a .Xauthority in /tmp. The only other option (besides changing the config) which came to my mind is, makeing a tunnel (netcat, or better ssh) from the remote host to the loginserver and copy the cookie manually (not sure if it the tcp-unix domain socket stuff works as expected). Any good suggestions (for the future - now our servers are already up)?

  Read the article

< Previous Page | 527 528 529 530 531 532 533 534 535 536 537 538  | Next Page >