Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 533/772 | < Previous Page | 529 530 531 532 533 534 535 536 537 538 539 540  | Next Page >

• Loads of memory in "standby" on Windows Server 2008 R2

  - by Jaap

  In our SharePoint farm, our Web Front End servers all have loads of memory in "standby" mode, meaning very little is available for our IIS worker process. We have 32 GB of RAM in each of the boxes, and standby memory will creep up to about 28 GB, whereas the IIS worker process only seems to be using about 2 GB. Also, we've seen the machine use the swap file extensively while this memory was in standby, so I am starting to think that this memory in standby mode is stopping IIS from using it, forcing it to swap to disk, causing more performance problems. I used SysInternals RamMap to indentify what is being kept in memory, and it was able to tell me that almost everything in standby memory is of type "Mapped File". When I sort the files listed under the file summary tab in RamMap by file size, the largest files (around a few hundred meg each) are IIS log files and SharePoint log files. I would like to understand which process is loading these files into standby memory and why they are not being released. When I do an iisreset, it does not release the memory. Any ideas? Thanks!

  Read the article

• w2k3 AD DC Demotion fails with "no other AD DC for that domain can be contacted"

  - by Kstro21

  i've a small office with a single w2k3 sp2 DC(bad idea, but it is real), now, i want to make a clean install of that pc, so, i got another one, install w2k3 sp2, add it to the domain, dcpromo and set it to be a GC, untill now everything is ok, then tried to dcpromo in the primary DC, but it fails with The box indicating that this domain controller is the last controller for the domain mydomain.com is unchecked. However, no other Active Directory domain controllers for that domain can be contacted. Do you wish to proceed anyway? If you click Yes, any Active Directory changes that have been made on this domain controller will be lost. So, i started to move all the roles to the new server as described here, when all was ok with the roles, i tried doing the same, but got the same result. Tried moving the DNS to the new server, but it doesn't make difference. Shutdown to the old server, then tried to log into a workstation, but it fails saying the domain is not available, also coudln't add new workstation to the domain, so i have to power on the old server again. So, if i successfully move all the roles and dns to the new server: why dcpromo give such message in the old server? why if i shutdown the old server the domain is not available?? if i successfully move all the roles and dns to the new server, and i click yes when dcpromo give warning in the old server, will i lose all users, computers, ou, etc.? am i missing some steps to make this work?? hope you can help me thanks

  Read the article

• In solaris, how monitor & auto-respond to critical events

  - by mamcx

  I have a website that randomly fail. Is running in open solaris on joyent. I have a monitoring service that alert me when the site is down, but, I want a way to put a "insider" tool that tell me why that happened. Is because the cpu is too high? Not memory? Which process fail? Is possible to have a backtrace of that? Everything is running on the Solaris Service Management Facility. The webserver is cherokee, the database is mysql and the language is python/django. I want the most simple setup to monitor that & auto-respond , ie: restart the webserver or the django process in case of failure. I prefer a low-overhead tool. I don't need the fancy monitoring that some tools have, no ned graphs or sms alert. Only know what fail, restart it if possible (maybe up to n times), and have a log somewhere when I will check it.

  Read the article

• Are there any critical reasons why one could not use ubuntu as a server platform?

  - by Chiggsy

  We were using Lenny. ( Well Sid, really ). Had to do that for development. I upgraded my server with ubuntu 10.04, for a different project. Noticed the packages. Wearing my developer hat, it's a no brainer. Everything we need is there. I'm the admin as well. We might need more than one "box" (running on VPS for now). I do not want to build things that apt would put on for me. It's not hard, but I'm going to need that time. The debian "box" has a bunch of stuff on it, that'll have to be integrated properly, but I think we are going live in a distressingly short time. (Just found out.) I am aware of the reflexive answers to this question. What I would like to ask is are there critical bugs or critical instabilities that would make one shy away from the ubuntu/server path? I could not find any bugs that would stop me, but perhaps there is something?

  Read the article

• VLAN Through Switch Doesn't Work

  - by vcsjones

  I have the following scenario: I have a Cisco Aironet 1040 access point. I have it configured with two SSIDs, each going to a different VLAN. So: SSID internal : VLAN 90 SSID guest : VLAN 70 On the router side, I have a Cisco RV220W (with the radios now turned off) and have setup VLANs with like VLAN IDs. VLAN 90 : 192.168.90.0/24 VLAN 70 : 192.168.70.0/24 As far as DHCP is concerned, each VLAN has a "DHCP Server" in the router's configuration: So with the access point connected directly to the router, everything works great. I connect to the internal network, and I get a 192.168.90.x address, and the guest network gets a 70.xxx address. Next I introduced a Cisco SG200-50 PoE switch between the router and the access point. The port is configured as a trunk port, so the VLAN tags should go right through the switch back to the router. However, when something is connected to the access point, nothing works. It isn't able to get an IP address, and manually assigning one doesn't seem to let any traffic route. Given that the access point works correctly when connected to the router directly, I believe the switch is misconfigured. What am I missing here? What can I use to better diagnose what the problem might be? It's small business equipment, so CLI access is not available. Below are screenshots of the switch's config. The access point is connected to GE2.

  Read the article

• Redirection of outbound UDP port NTP.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• KeePass lost password and/or corruption due to Dropbox/KeePassX

  - by GummiV

  I started using Keepass about a month ago to hold my passwords and online accounts info. Everything was stored in a single .kdb file, only protected with a password. I'm using Windows 7. Now Keepass can't open my .kdb file with the error "Invalid/wrong key". I'm fairly confident I have the right password. Altough I might have mixed up a few letters I've tried about two dozen different combinations to minimize that possibility - but can't rule it out though. My guess is however that the .kdb file got corrupted, either due to Dropbox syncing (only using it on one computer though) or because I edited the file using KeePassX on Ubuntu (dual boot on the same computer, accessing a mounted Win7 NTFS partition), or possibly a combination of both. I have tried restoring older versions(even the original one) from Dropbox and trying out all possible passwords without any luck. (which does seem to rule out KeePassX as the culprit, since oldest copies are before I edited the file from Ubuntu) I have tried opening the file with the "Repair KeePass Database file" which always gives the "0xA Invalid/corrupt file structure" (the same error for when a wrong password is typed). I was wondering if there was any way for me to salvage my hard-gathered data. I know generally that brute force cracking is not feasible, but since I can remember probably more than half of the usernames/passwords, any maybe the fact that one of them does come up fairly often (my go-to pass for trivial stuff), that might simplify the brute force process to a doable time frame. Maybe the brute-force thing might incorporate the fact that I know the password length and what characters it's made from. (If we assume corruption, not a password-blackout on my part) I could do some programming if there are any libraries or routines that I could use. Other people seem to have had a similar probem http://forums.dropbox.com/topic.php?id=6199 http://forums.dropbox.com/topic.php?id=9139 http://www.keepassx.org/forum/viewtopic.php?t=1967&f=1 So hopefully this question will become a suitible resource for people when searching the web. Feel free to tell me if you think this should rather be a community wiki.

  Read the article

• Fixing a typo in machine name

  - by justSteve

  When i installed windows i had a typo in the machine name that i corrected from the system's 'Computer Name/Domain Changes' - the workstation is a member of a workgroup not a domain. From everything i can see the renamed machine name is correct. Shift gears.... I'm importing SQL logins from my remote server to this, my development workstation and have used the script presented here - a script that generates a CREATE statement for each login found. While I was preparing to run this script's output (from the remote box) i needed to change the domain name from the remote to my local's name - so i ran the same script locally (in order to see what SQL things my domain name is. SQL has the original machine name - the one with the typo. However, the scripts are tossing errors if i try to create logins with that identifier. CREATE LOGIN [Setve\Admin] FROM WINDOWS WITH DEFAULT_DATABASE = [master] But works correctly if i use the updated machine name: CREATE LOGIN [Steve\Admin] FROM WINDOWS WITH DEFAULT_DATABASE = [master] So the problem is: do i have a problem i need to solve? Somewhere, deep in the guts of SQL Server, it has record of a Domain name that does not exist. Should i find and fix that discrepancy? thx

  Read the article

• How can I switch from a custom linux network namespace back to the default one?

  - by Martin

  With ip netns exec you can execute a command in a custom network namespace - but is there also a way to execute a command in the default namespace? For example, after executing these two commands: sudo ip netns add test_ns sudo ip netns exec test_ns bash How can the newly created bash execute programs in the default network namespace? There is no ip netns exec default or anything similar as far as I've found. My scenario is: I want to run a SSH server in a separate network namespace (to keep the rest of the system unaware of the network connection, as the system is used for network testing), but want to be able to execute programs in the default network namespace via the SSH connection. What I've found out so far: Created network namespaces are listed as files under /var/run/netns (but there is no file for the default namespace) The ip netns exec code can be found here: http://git.kernel.org/cgit/linux/kernel/git/shemminger/iproute2.git/tree/ip/ipnetns.c#n132 - I haven't grasped everything that it is doing yet, but it doesn't look very promising. ip netns identify $$ as suggested by Howto query and change network namespace on linux? returns nothing when in the default network namespace

  Read the article

• Relaying to tech "support" that computer is actually broken.

  - by Sion

  First some background: I have a Dell Inspiron 15R M050, it is still under the Dell limited warranty and the Best Buy Extended warranty. I am currently dual booting Debian Squeeze and Windows 7, the only reason I go into Windows is to play video games specifically steam games. Issue: When I play my games in Windows I am capable of playing for anywhere from 5 minutes to 2 hours before I suffer a hard-lock. I cannot alt-tab, ctrl-alt-delete, ctrl-shift-escape do anything for 2-3 minutes. After this hard-lock period everything runs fine, I can continue the game for probably another hour at least before I suffer another lock. Games: Borderlands, Splinter Cell: Chaos Theory, Starcraft 2, Garrys Mod What I have tried: Running the diagnostic suite in the dell bios, restoring the OEM Windows recovery partition on the HD, fresh installing Windows 7 Professional, updating BIOS, Calling tech support and having them run a software Hardware Diagnostics suite. The question: I think from the research that I have performed that it might be a lack of thermal paste on the CPU, would I be able to go to Best Buy and have them do a hardware diagnostic from the hardware level then have them be able to tell Dell that there is a hardware issue? Or would there be a different problem?

  Read the article

• emacs ORG-mode "headless" export-as commands?

  - by Seamus

  When I use org-export-as-latex or org-export-as-html orgmode turns my buffer into a .tex file or .html file. But I don't want all the extra junk that it adds to the file: I want to handle the documentclass and everything myself and just \input the org mode generated file. (Or the analogous things for html with php). So if my org file just has: * Section - Stuff - Things I want the org mode command to output just \section{Section} \begin{itemize} \item Stuff \item Things \end{itemize} Without any of the extra \tableofcontents junk that ORG adds to it. I know I could define my own kind of #+LaTeX_CLASS that could add the packages I want and so on, but I don't want to do things that way (and that wouldn't remove the \maketitle or the spurious \vspace* that ORG insists on inserting. Is there a command to do this "headless" parsing and converting? I had a look but it's not obvious from the documentation. Presumably some low level ORG command is doing the parsing and converting I want, but I couldn't find what it was called from looking at the docs and C-h pages... This is not a question about HTML or LaTeX but about emacs ORG mode. So don't kick it off to some other site...

  Read the article

• Postgres pgpass windows - not working

  - by Scott

  DB: Postgres 9.0 Client: Windows 7 Server Windows 2008, 64bit I'm trying to connect remotely to a postgres instance for purposes of performing a pg_dump to my local machine. Everything works from my client machine, except that I need to provide a password at the password prompt, and I'd ultimately like to batch this with a script. I've followed the instructions here: http://www.postgresql.org/docs/current/static/libpq-pgpass.html but it's not working. To recap, I've created a file on the client (and tried the server as well): C:/Users/postgres/AppData/postgresql/pgpass.conf, where postgresql is the db user. The file has one line with the following data: *:5432:*postgres:[mypassword] (also tried explicit ip/dbname values, all asterisks, and every combination in between. (I've also tried replacing each '*' with [localhost|myip] and [mydatabasename] respectively. From my client machine, I connect using: pg_dump -h [myip] -U postgres -w [mydbname] [mylocaldumpfile] I'm presuming that I need to provide the '-w' switch in order to ignore password prompt, at which point it should look in the AppData directory on the server. It just comes back with "connection to database failed: fe_sendauth: no password supplied. Any insights are appreciated. As a hack workaround, if there was a way I could tell the windows batch file on my client machine to inject the password at the postgres prompt, that would work as well. Thanks.

  Read the article

• FFmpeg convert video w/ dropped frames, out of sync

  - by preahkumpii

  I recorded a video using Bandicam with the MJPEG encoder to get the least amount of lag. Now, I am trying to convert that massive file to a h264 avi using ffmpeg. I know there are dropped frames in the video stream...more than 100 in the first two minutes, which I assume is simply because Bandicam dropped some when it couldn't keep up. So, when I convert the file to h264, the video and audio are out of sync, and appear to be more and more out of sync as output video progresses. Here is my basic command in ffmpeg: ffmpeg -i "C:\...\input.avi" -vcodec libx264 -q 5 -acodec libmp3lame -ar 44100 -ac 2 -b:a 128k "C:\...\output.avi" I have tried EVERYTHING I can think of including: -itsoffset [-]00:00:01 Tried this before and after input file. This doesn't work because as the video progresses it becomes more and more out of sync. -async 1 Doesn't work. -vsync 1 Doesn't work, but it does show dropped frames being duplicated. Two inputs of same file with mapping using -map 0:0 -map 1:1. Doesn't work. The source plays just fine. Any ideas how to convert it with ffmpeg and keep the audio and video synced? Thanks.

  Read the article

• Problems configuring logstash for email output

  - by user2099762

  I'm trying to configure logstash to send email alerts and log output in elasticsearch / kibana. I have the logs successfully syncing via rsyslog, but I get the following error when I run /opt/logstash-1.4.1/bin/logstash agent -f /opt/logstash-1.4.1/logstash.conf --configtest Error: Expected one of #, {, ,, ] at line 23, column 12 (byte 387) after filter { if [program] == "nginx-access" { grok { match = [ "message" , "%{IPORHOST:remote_addr} - %{USERNAME:remote_user} [%{HTTPDATE:time_local}] %{QS:request} %{INT:status} %{INT:body_bytes_sent} %{QS:http_referer} %{QS:http_user_agent}” ] } } } output { stdout { } elasticsearch { embedded = false host = " Here is my logstash config file input { syslog { type => syslog port => 5544 } } filter { if [program] == "nginx-access" { grok { match => [ "message" , "%{IPORHOST:remote_addr} - %{USERNAME:remote_user} \[% {HTTPDATE:time_local}\] %{QS:request} %{INT:status} %{INT:body_bytes_sent} %{QS:http_referer} %{QS:http_user_agent}” ] } } } output { stdout { } elasticsearch { embedded => false host => "localhost" cluster => "cluster01" } email { from => "[email protected]" match => [ "Error 504 Gateway Timeout", "status,504", "Error 404 Not Found", "status,404" ] subject => "%{matchName}" to => "[email protected]" via => "smtp" body => "Here is the event line that occured: %{@message}" htmlbody => "<h2>%{matchName}</h2><br/><br/><h3>Full Event</h3><br/><br/><div align='center'>%{@message}</div>" } } I've checked line 23 which is referenced in the error and it looks fine....I've tried taking out the filter, and everything works...without changing that line. Please help

  Read the article

• Does Antivirus2009 or Antivirus360 automatically install on your computer and if so how?

  - by sergey

  I run Firefox on Vista, and unfortunately I got tricked (through a deceptive google result) into going to a page containing one of those fake "Your Computer Has all of this Spyware on it!" pages. I tried manually closing the tab, but it had a "Are you sure you want to navigate away" JavaScript alerts (HATE THOSE). So I clicked "OK," and the tab closed. Then I closed firefox altogether and rebooted. Now, before I could close the tab, it did prompt me to download a file, but of course I choose not to, and checking my downloads folder, nothing new is there. Also, even if I ?did? download it, ?I? would still have to choose to run it by double clicking on it for it to install itself, right? Also, I ran Malware Bites and Windows Defender and both said everything was fine. From this I would normally believe I am safe, but I have read everywhere that this thing "automatically installs" itself and that it is a bitch to get rid of. Is it really possible for this thing to dig in if you are running firefox and didn't choose to download it or run it after downloading?

  Read the article

• Mouse clicks suddenly stopped working in Ubuntu

  - by DisgruntledGoat

  This is a weird one. For some reason, last night my mouse partially stopped working. Movement is fine, but the mouse buttons don't work. Mainly it's the left button, but occasionally the right click and scroll-wheel fail too. Initially I thought it could be the mouse itself (the left button seemed to get a bit "soft" recently), but I tried another mouse and had the same issue. Both are USB wireless optical mice. The keyboard is working okay 95%, only problem is Alt+Tab doesn't seem to work. Both keys work fine independently. At the time it happened I was using Chrome, I dragged to scrollbar to scroll and when I released the mouse it was still holding scrollbar. I'm using Ubuntu 9.10, I upgraded weeks ago and everything was working fine so I don't think it's related to that. I also hadn't run any updates (I have now just in case something fixed it). But no luck. Any ideas?

  Read the article

• Dell XPS 1530 DVD-RW firmware problem

  - by josecortesp

  Hello everyone. I have this XPS laptop since a year and a half ago. About 2 months ago, with the waranty expired, i tried to run the optiarc slot load DVD-RW firmware update, and said everything was okay. Then I restarted it and the problem started: Now, every single time I turn on my computer, it get stuck at the BIOS POST until the drive sounds like "ready" and then the computer starts normally. And this happen EXACTLY the same when it's getting back from sleep. I'm pretty sure is not a software issue, because I tried with Vista Home Premiun 32 bits, Ubuntu (from 8.10+)32 & 64, and with W7 64. Already tried to run the firmware installer like a million time, in case it is a failing install with no luck. Also, google it to see if someone has the same problem, and again, no. The Drive performs pretty okay once the System is on, but waiting to the drive to be ready everytime is really annoying. The Firmware I updated was this, and the drive is: K937C Assembly, Dvd+/-rw, 8, SLOT, 1530 Sony Nec Optiarc Inc. I'll apreciate any help you can give me

  Read the article

• What is the difference between these Pentium Extreme Edition CPUs?

  - by Giffyguy

  The CPU in question is the Pentium Extreme Edition 955. Intel's website shows four "versions", but for the most part they all look identical. They even share the same set of ordering codes. But one of them has a substantially lower TDP, which is seemingly unexplainable - since everything else is the same. Two of them say "LGA775, Tray" and I have no idea what "Tray" means either. Also, two of them have a different SPEC code. What I need to know is: What does "LGA775, Tray" mean? Why does the one CPU have a lower TDP? And what does that mean for me? Does that mean lower maximum power consumption? Does it mean the CPU may be more stable/endurant, because of a lower heat output? Why do two of them have a different SPEC code, and what does this mean? Finally, what does PLGA775 (as opposed to LGA775) mean, and do I need to be worried about that? Information from Intel's wbsite: Intel® Pentium® Processor Extreme Edition 955 (4M Cache, 3.46 GHz, 1066 MHz FSB) with SPEC Code 1 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 95 Watts BX80553955 SL94N 2 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL94N 3 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 130 Watts BX80553955 SL8WM 4 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL8WM

  Read the article

• OS X can connect to Windows machine, but can't access shared folders

  - by Bonnie

  I can create new folders on my Windows XP machine, set them to "shared". On my Mac, I pick Finder → Go → Connect to Server → smb://192.168.1.4 → Connect → Name / Password. It even shows me all the names of the newly created shared-folders on my PC, but when I try to actually connect to any of them I get connection failed, there was an error connecting Any idea on what would cause that? The fact that it successfully gets so far—to actually showing me my PC share-names—must mean I have 99% of this working correctly, i.e. the physical connection, the IP address, the user name, the password, etc. Still, I can't seem to access the folders themselves. I've tried this with my Windows XP firewall on/off, and Norton AntiVirus on/off. Same problem. Everything did work fine, 4 months ago. Were there any odd OS X or Windows updates released recently? I always apply them all. smbclient on the Mac does correctly find the XP machine, my XP user name, and accepts my XP password. I get the following from that smbclient command: Doing spnego session setup (blob length=16) server didn't supply a full spnego negprot Got challenge flags: ... Got NTLMSSP flags: ... Got NTLMSP flags: ... Domain=[XPMACHINE] OS=[Windows 5.1] Server=[Windows 2000 LAN Manager] tree connect failed: NT_STATUS_INSUFF_SERVER_RESOURCES I'm not sure why a standard XP box can't "supply a full spnego negprot". Whatever that means. Using XP's RegEdit to change my IRPStackSize from 11... to 13, 15, 20, 22... still gives that "NT_STATUS_INSUFF_SERVER_RESOURCES" error on the Mac.

  Read the article

• Windows 7 ssh file server.

  - by Siriss

  Hello all- I have looked at the other posts, but have not quite found an answer I have a question about windows file sharing over SSH. I have copssh installed and it is working for Remote desktop connections. I have port 22 forwarded on my router etc. I connect from a Mac or Putty with this address: ssh -l copsshusername 3391:localhost:3389 [external ip] That works fine. I would like to configure Windows 7 to allow my ssh account that I use to login, access to certain shared folders. I have documents and videos and things that I would like to be able to download externally. I have done this before on Linux and a long time ago on XP, but I cannot figure out what I am missing on Windows 7. There is a designated SSH user that copssh uses to run the service and that I use to to login as. I have googled and googled and have not found a solution that does everything I need that is why I am turning here for ideas. I hope I am explaining this correctly. Thank you very much for your help!

  Read the article

• Dell PowerEdge 860 won't boot but gets power

  - by fierflash

  I have a Dell PowerEdge 860. Got an 2008 R2 running on it. Here is the scenario I'm currently in: I can boot it up and work as usuall. But when I restart it, it just shuts down, doesn't reboot, and it won't boot up again. Then it stays in this "mode", On/off button blinking green(standby mode?) and System Indicator LED blinking amber. If I try to press the On/Off button on the frontpanel it won't boot. It's like you can hear the fan from the PSU running but nothing else is trying to boot. If I unplug the powercable and then put it back in again it's the same, the extremley noisy fans won't start and it's just sitting there. If I let it "rest" for like 1 to 24 hours while the powercable is unplugged and I plug it in again, it boots directly, without me having to push the On/Off button. What I have tried: Run diagnostics(not the one in POST phase) and everything is fine Booting without any cables except the powercable Boot without memory installed Boot without the raidcable plugged in Cleared NVRAM Reseated all the components and cables Googling like a freak for any possible solution Tried Dell Support but I don't have any warranty left so they can't help me unless i pay some ridiculous amount of money I suppos Do anyone have some experience with the same issue? Do I need to replace something or is there any other way to determine the problem? Any help will be greatly appreciated.

  Read the article

• SharePoint Web Analytics not tracking usage for main application

  - by Chris W

  My SP 2010 setup is two separate applications - one for the main portal and one for MySite. Whilst WebAnalytics is tracking usage of MySite it's not showing any stats for the main Portal. The only thing it lists is the number of site collections but no page views etc. The WA service is clearly running to pick up data for MySite. In Configure web analytics and health data collection everything is ticked. I can't find any obvious settings that are different between the two applications. Where should I look to get usage tracking correctly? Edit: Having played with the date ranges I see that actually I've got no stats in the last 7 days for any site at all including MySite which has been working at some point previously. Edit: What does each service (WA Data Processing Service vs WA Web Services) do and where should they be active? At present they're both running on an App server but not on the WFEs (although they were running on WFEs previously). From what I can gather than only need to run on an App server but I find it strange that the only logged activity I see in the staging database relates to Central Admin URLs on the App server and nothing from the WFEs.

  Read the article

• VLAN Tagging Traffic on Cisco Switch

  - by David W

  I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

  Read the article

• Metacity/Compiz not staring upon Login Ubuntu 10.10

  - by Ryan Lanciaux

  TLDR: As of this afternoon, I do not have a window manager when I login to Ubuntu 10.10. I would like to have window manager on login without needing to add to startup. Just started using linux again as my home OS. (Used it for a long time years ago but been on windows up until this past weekend) so this may be kind of n00b-ish :) Anyways, up until today, everything on my machine was running okay. I did not have compiz running as the default wm because I'm running NVidia Drivers and Xinerama (and as I understand Xinerama & Compiz don't work well together). I made no changes to my xorg / etc but today when I logged in, I had to manually start metacity from command line to get any window manager. Really not sure what would be causing this or what I can do to get it working again. My xorg.conf is available here: https://gist.github.com/845618. My default Window Manager is set to /usr/bin/metacity in Configuration Editor under /desktop/gnome/applications/window_manager. p.s. Any tips on how to run 3 monitors where I can move windows between screens without Xinerama would be appreciated but that's prolly for another thread :)

  Read the article

• MacBook Air Keeps dropping Wi-Fi

  - by Robert Patrick

  So my MacBook Air keeps dropping Wi-Fi for some reason. It happens ONLY on my home network, and ONLY to my computer. I'm using a Linksys WRT54G router. I'm the only Mac on the network. Every other Wi-Fi network is perfectly fine, and every other computer on this network is fine. Many things can happen. It could say it's connected, but not be able to access the internet (whether it tells me that there's no internet access or not). It may just drop Wi-Fi altogether, and refuse to connect. Generally, if I unplug the router and plug it back in, it's all good. It also works if I restart my computer. This happens multiple times a day. Yesterday I did everything I know to get it to connect (restart router many times, restart my MacBook), and nothing worked. Eventually it just magically worked. How can I stop this from happening? We got a notice from Comcast a while ago saying that a bot called DNS Changer was detected on one or more machines on the network. I'm assuming that this can't be me, right?

  Read the article

< Previous Page | 529 530 531 532 533 534 535 536 537 538 539 540  | Next Page >