Search Results

Search found 16894 results on 676 pages for 'block device'.

Page 534/676 | < Previous Page | 530 531 532 533 534 535 536 537 538 539 540 541  | Next Page >

• Using mixed disks and OpenFiler to create RAID storage

  - by Cylindric

  I need to improve my home storage to add some resilience. I currently have four disks, as follows: D0: 500Gb (System, Boot) D1: 1Tb D2: 500Gb D3: 250Gb There's a mix of partitions on there, so it's not JBOD, but data is pretty spread out and not redundant. As this is my primary PC and I don't want to give up the entire OS to storage, my plan is to use OpenFiler in a VM to create a virtual SAN. I will also use Windows Software RAID to mirror the OS. Partitions will be created as follows: D0 P1: 100Mb: System-Reserved Boot D0 P2: 50Gb: Virtual Machine VMDKs for OS D0 P3: 350Gb: Data D1 P1: 100Mb: System-Reserved Boot D1 P2: 50Gb: Virtual Machine VMDKs for OS D1 P3: 800Gb: Data D2 P1: 450Gb: Data D3 P1: 200Gb: Data This will result in: Mirrored boot partition Mirrored Operating system Mirrored Virtual machine O/S disks Four partitions for data In the four data partitions I will create several large VMDK files, which I will "mount" into OpenFiler as block-storage devices, combined into three RAID arrays (due to the differing disk sizes) In effect, I'll end up with the following usable partitions SYSTEM 100Mb the small boot partition created by the Windows 7 installer (RAID-1) HOST 50Gb the Windows 7 partition (RAID-1) GUESTS 50Gb Virtual machine Guest VMDK's (RAID-1) VG1 900Gb Volume group consisting of a RAID-5 and two RAID-1 VG2 300Gb Volume group consisting of a single disk On VG1 I can dynamically assign storage for my media, photographs, documents, whatever, and it will be safe. On VG2 I can dynamically assign storage for my data that is not critical, and easily recoverable, as it is not safe. Are there any particular 'gotchas' when implementing a virtual OpenFiler like this? Is the recovery process for a failing disk going to be very problematic? Thanks.

  Read the article

• Enabling Samba Shares Across Subnets

  - by John

  I was curious how I could go about setting up SAMBA so that shares could be seen and used across different subnets. We have some Linux devices that are bound to Active Directory and we would like to have them serve SAMBA shares to clients that will reside in a different subnet than what the servers reside in? Is there any way to do this without needing to setup a WINS server or use legacy NetBIOS methods since the majority of our clients are Windows 7, Windows Server 2003, Windows Server 2008, and Macintosh OS X (10.6 or newer)? EDIT Right now, only clients in the same subnet as the SAMBA server can see the shares. Clients outside of the subnet (i.e. the client subnet) cannot see or connect to the share. The error returned is: The specified network name is no longer available. It does not seem to matter if I use IP, FQDN, or NetBIOS name to try and connect to the share with. We have a common Cisco router handling the inter-subnet routing. Everything else seems to work correctly with this network setup and the device can be pinged from multiple subnets. I also do not believe it to be a firewall type of issue since the rules for this segment are rather lax.

  Read the article

• Dual booting Linux/Win7, Grub refuses to load Win7

  - by JohnB

  Decided to give Linux Mint a try (Ubuntu's interface annoys me), so I installed it with the intention of dual booting with Windows 7. Installation went fine, but now I can only boot into Linux Mint. Grub lists two Windows 7 menu options, but selecting either of them causes an "unknown file system" error and dumps me into a Grub recovery prompt. There, I have to manually reset the root and prefix options, as they reset hd0,msdos6 when they should be hd0,msdos5. I ran Boot Repair twice, once to fix grub errors, once to rebuild the MBR, but it didn't fix anything. Here is the log: http://paste.ubuntu.com/1029675/ fdisk output: Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 1486249145 743021149 7 HPFS/NTFS/exFAT /dev/sda3 1486249982 1953523711 233636865 5 Extended /dev/sda5 1486249984 1945141247 229445632 83 Linux /dev/sda6 1945143296 1953523711 4190208 82 Linux swap / Solaris grub.cfg: ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 86184D18184D091F chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda2)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 56D84F84D84F60FB chainloader +1 } ### END /etc/grub.d/30_os-prober ### I have found a few similar troubleshooting guides so far, but so far no amount of updating/configuring Grub has been successful. Last resort is, I suppose, use the W7 recovery disc and start over. Thanks in advance! Linux Mint 13 Maya, 64-bit Windows 7 Home Edition, 64-bit

  Read the article

• fax server farm architechture

  - by Brian Postow

  I'm not sure this is the right forum for this, but it's not Stackoverflow so... I'm trying to figure out an architecture to solve the following problem, maybe someone here can help: I have a T1 with 23 fax lines coming into the building. I have a computer (Macintosh XServe) running Hylafax. If I had one POTS line, I'd be done. However, I have no idea how to get the T1 into the Mac... Options I've considered: some sort of PCI T1-modem (Does that exist?) Splitting the T1 into 23 POTS lines and then connecting 23 analog modems to the mac, either via an external modem bank (Do they still make those?) or via some sort of external PCI bank, which will allow me to use more than 2 4-port modem cards. Either the T1 or the split POTS lines going into some intermediate device and then transfering the images over IP, or USB to the mac. Really, any other option I can come up with This has GOT to be a problem that someone has already solved, right?

  Read the article

• Windows Server 2008 network speed slow, Xen 3.4.3 HVM ISO

  - by Elliot.Bradshaw

  I've setup a VM running Windows Server 2008 on a host node running Xen 3.4.3-5 and the following kernel: 2.6.18-308.1.1.el5xen #1 SMP Wed Mar 7 05:38:01 EST 2012 i686 i686 i386 GNU/Linux The network speed on the VM is very slow--using the online speed tests I can only get it up to 8-9mbps. The line is 100mbps burstable and the host node has no problem achieving those speeds. If it setup a VM running CentOS, it too has no problems achieving those speeds. I've done some pretty exhaustive troubleshooting, but nothing has helped: New VM installations of Win2k8 do have the same network problem. Upgrading to most recent kernel-xen did not help (2.6.18-308.1.1.el5xen). Upgrading from xen 3.4.0 to xen 3.4.3-5 did not help. Disabling Windows firewall, etc did not help. Changing network card device config from auto negotiation to manually be 100mbps full duplex did not help. Changing the network receive buffer packet size did not help (tried all combos from 64k to 8k). At this point I'm pretty much out of ideas--any help would be appreciated!

  Read the article

• simple network between xp & 7 with cross cable problem...

  - by LostLord

  hi my dear friends : i have a simple network between xp & 7 windowses with cross cable (2 pc home)... ===================================================================== the one with 7 is mother and have 2 lan device (onboard + pci) A. onboard is like this when u go to tcp/ip v4 properties:(4 adsl internet) obtain an ip... preferred dns server : 81.91.129.67 alternate dns server : 4.2.2.4 shared...no permission 4 change so every thing is ok for internet on windows 7. B. the other lan pci card that is connected to pc with xp is like this : 192.168.2.11 255.255.255.0 0.0.0.0 empty empry computer name : cougar workgroup : nethome homeNetwork is disabled (i think that is 4 2 pc's with 7 os not xp) every thing is off in network options except file & printer sharing in public area ===================================================================== pc with xp os is like this : 192.168.2.12 255.255.255.0 192.168.2.11 (mean gateway) 4.2.2.4 8.8.8.8 computer name : tiger workgroup : nethome ===================================================================== at last my little net is ok... mean both have internet , both can see each other by their ip (\\192.168.2.11 or \\192.168.2.12) my problem is when in pc with xp type \\cougar it shows an error about network path! but in pc with 7 \\tiger works perfec. what is the problem in system with xp ? in few days ago this network was ok (search by computer name) when both os were xp , so there is no problem with my cable or devices. another problem is i can not find tiger in my network list in 7 pc \ why? is something wrong with my network? thanks 4 future advance best regards

  Read the article

• How to whitelist external access to an internal webserver via Cisco ACLs?

  - by Josh

  This is our company's internet gateway router. This is what I want to accomplish on our Cisco 2691 router: All employees need to be able to have unrestricted access to the internet (I've blocked facebook with an ACL, but other than that, full access) There is an internal webserver that should be accessible from any internal IP address, but only a select few external IP addresses. Basically, I want to whitelist access from outside the network. I don't have a hardware firewall appliance. Until now, the webserver has not needed to be accessible externally... or in any case, the occasional VPN has sufficed when needed. As such, the following config has been sufficient: access-list 106 deny ip 66.220.144.0 0.0.7.255 any access-list 106 deny ip ... (so on for the Facebook blocking) access-list 106 permit ip any any ! interface FastEthernet0/0 ip address x.x.x.x 255.255.255.248 ip access-group 106 in ip nat outside fa0/0 is the interface with the public IP However, when I add... ip nat inside source static tcp 192.168.0.52 80 x.x.x.x 80 extendable ...in order to forward web traffic to the webserver, that just opens it up entirely. That much makes sense to me. This is where I get stumped though. If I add a line to the ACL to explicitly permit (whitelist) an IP range... something like this: access-list 106 permit tcp x.x.x.x 0.0.255.255 192.168.0.52 0.0.0.0 eq 80 ... how do I then block other external access to the webserver while still maintaining unrestricted internet access for internal employees? I tried removing the access-list 106 permit ip any any. That ended up being a very short-lived config :) Would something like access-list 106 permit ip 192.168.0.0 0.0.0.255 any on an "outside-inbound" work?

  Read the article

• Sharing disk volumes across OpenVZ guests to reduce Package Management Overhead

  - by andyortlieb

  Is it feasible to create a single "master" OpenVZ guest who would only be used for package management, and use something like mount --bind on several other OpenVZ guests sort of trick them into using the environment installed by the master guest? The point of this would be so that users can maintain their own containers, and yet stay in sync with the master development environment, so they'll always have the latest & greatest requirements without worrying too much about system administration. If they need to install their own packages, could put them in /opt, or /usr/local (or set a path to their home directory)? To rephrase, I would like several (developer's, for example) OpenVZ guests whose /bin, /usr (and so on...) actually refer to the same disk location as that of a master OpenVZ guest who can be started up to install and update common packages for the environment to be shared by all of this group of OpenVZ guests. For what it's worth, we're running Debian 6. Edit: I have tried mounting (bind, and readonly) /bin, /lib, /sbin, /usr in this fashion and it refuses to start the containers stating that files are already mounted or otherwise in use: Starting container ... vzquota : (error) Quota on syscall for id 1102: Device or resource busy vzquota : (error) Possible reasons: vzquota : (error) - Container's root is already mounted vzquota : (error) - there are opened files inside Container's private area vzquota : (error) - your current working directory is inside Container's vzquota : (error) private area vzquota : (error) Currently used file(s): /var/lib/vz/private/1102/sbin /var/lib/vz/private/1102/usr /var/lib/vz/private/1102/lib /var/lib/vz/private/1102/bin vzquota on failed [3] If I unmount these four volumes, and start the guest, and then mount them after the guest has started, the guest never sees them mounted.

  Read the article

• Xen guests accessing LUNs

  - by mechcow

  We are using RHEL5.3 with a Clarion SAN attached by FC. Our situation is that we have a number of LUNs presented to Hosts and we want to dynamically present the LUNs to Xen Guests. We are not sure on what the best practice approach is to set this up. The Xen guests will form a cluster together and need the LUNs only for data partitions, i.e. when they are actively running services. So one approach would be to always present all disks to all Xen guests, and then rely up on the cluster software, and mount itself, to not mount the disk twice in two locations. This sounds kinda risky and also is not very secure (one cracked guest can see/destroy all the data). Another approach would be to dynamically add and remove the disks from the Xen guests at the dom0 level (using xm block-attach). This could work but sounds slightly complicated, I'm wondering whether Red Hat Cluster Suite supports this in some way or whether there are scripts to do this. Yet another approach would be to have the LUNs endpointed at the Xen guests themselves - I'm not sure whether this is technically possible since the multipathing has to be done at the Host level.

  Read the article

• Poor gaming performance with hyper-v installed in windows 8

  - by SnowCrash

  I am getting very poor gaming performance on my Windows 8 host OS with Hyper-V installed but no guest machines running. For example World of Tanks reports 60-70 FPS without Hyper-V installed and 4-14 FPS with it installed. A similar, dramatic, hit is observed in several other games so the issue is not WoT specific. To make the point clear, I am not trying to run games in a virtual machine. I don't even have a VM running while observing this effect. I simply have the Hyper-V feature installed. My system specs: AMD Phenom II 965 (3.4 GHz) AMD Radeon 6950 2GB (XFX Double D HD-695X-CDFC) 16GB DDR3 1333 AMD 790GX chipset Mainboard (Gigabyte GA-MA790GPT-UD3H) I have tried every AMD driver from 12.8 to the current 12.11beta8, virtualization is enabled in the BIOS settings, the onboard 3300HD video device is disabled in BIOS and I have read the MSDN blog entry here regarding a similar issue in Server 2008 that was resolved in 2008 R2 (and hopefully not regressed in Win 8). I'd like to be able to use Hyper-V for development and testing at home (I am a sysadmin/software developer professionally). If, however, I can't also use my home system for entertainment I'll have to scrap those plans.

  Read the article

• How to restrict zone transfers to specific authorized servers only

  - by JonoB

  I recently failed a PCI compliance scan because of the following: This DNS server allows unrestricted zone transfers. Attackers may be able to use this information to gain knowledge on the structure of your networks to aid in device discovery prior to an actual attack. And the suggested solution is as follows: Reconfigure this DNS server to restrict zone transfers to specific authorized servers only. I am running a dedicated Linux Centos server. My understanding is that I have to edit the /etc/named.conf file, which I have done and the the relevant part is as follows: options { acl "trusted" { 127.0.0.1; xxx.xxx.xxx.001; //this is one of the server's ip's xxx.xxx.xxx.002; //this is another server's ip }; allow-recursion { trusted; }; allow-notify { trusted; }; allow-transfer { trusted; }; }; I then restarted the named service /etc/rc.d/init.d/named restart and requested a re-scan, which failed again for the same reason. Am I missing something obvious here?

  Read the article

• Alternate way to connect a vpn through a MIFI

  - by questor

  This has gotten to be a major problem at our company and depending on who I ask, the problem either does not really exist (mfr. and vendor) or is insoluble ( according to most users including techs who know how to prove their point). The problem involves getting a normal Windows 7 system to connect to a normal Server 2008 R2 Server over a cellular router (usually called a Mifi). A very few brands/models appear to work but the majority cannot make the connection. Since it is a cellular device, there are many variables that come into play and I wondered if anyone had ever found a consistent way to either make one work or else prove to the providers that their equipment was at fault. They all specifically state “VPN use” on the sales brochures. But few if any work. And those that do are not reliable. From a standpoint of pure knowledge, I just wondered if anyone knew the real reason why they fail? Pptp, L2tp, IPsec doesn’t matter. I have not tried Shrew or OpenVPN and am using strictly MS Windows protocols. Plenty of Google Searches back up my complaints but none seem to be any closer to knowing "why" they fail, just that they do. This is a "quest for knowledge"question. I don't expect a solution. Just a reason for the problem if anyone has any ideas.

  Read the article

• How can i get more low memory with the following setup:

  - by user539484

  Modules using memory below 1 MB: Name Total = Conventional + Upper Memory -------- ---------------- ---------------- ---------------- MSDOS 14 317 (14K) 14 317 (14K) 0 (0K) HIMEM 1 120 (1K) 1 120 (1K) 0 (0K) EMM386 3 120 (3K) 3 120 (3K) 0 (0K) OAKCDROM 36 064 (35K) 36 064 (35K) 0 (0K) POWER 80 (0K) 80 (0K) 0 (0K) NLSFUNC 2 784 (3K) 2 784 (3K) 0 (0K) COMMAND 2 928 (3K) 2 928 (3K) 0 (0K) MSCDEX 15 712 (15K) 15 712 (15K) 0 (0K) SMARTDRV 30 384 (30K) 13 984 (14K) 16 400 (16K) KEYB 6 752 (7K) 6 752 (7K) 0 (0K) MOUSE 17 296 (17K) 17 296 (17K) 0 (0K) DISPLAY 8 336 (8K) 0 (0K) 8 336 (8K) SETVER 512 (1K) 0 (0K) 512 (1K) DOSKEY 4 144 (4K) 0 (0K) 4 144 (4K) POWER 4 672 (5K) 0 (0K) 4 672 (5K) Free 552 944 (540K) 539 088 (526K) 13 856 (14K) Memory Summary: Type of Memory Total = Used + Free ---------------- ---------- ---------- ---------- Conventional 653 312 114 224 539 088 Upper 47 920 34 064 13 856 Reserved 0 0 0 Extended (XMS)* 64 898 256 2 671 824 62 226 432 ---------------- ---------- ---------- ---------- Total memory 65 599 488 2 820 112 62 779 376 Total under 1 MB 701 232 148 288 552 944 Total Expanded (EMS) 33 947 648 (33 152K Free Expanded (EMS)* 33 538 048 (32 752K * EMM386 is using XMS memory to simulate EMS memory as needed. Free EMS memory may change as free XMS memory changes. Largest executable program size 538 976 (526K) Largest free upper memory block 7 488 (7K) MS-DOS is resident in the high memory area. I'm running MS-DOS 6.22 on VMWare virtual hardware. This is memory state after memmaker pass, so i'm looking for optimization beyond memmaker. Note: NLS drivers (DISPLAY, KEYB, NSLFUNC) are essential for me. Thanks to @mtone for valuable reminder about MSCDEX /E which gave me 16KiB of low memory (see the diff)!

  Read the article

• Windows won't sleep after booting from grub

  - by mkasberg

  I recently added a second hard drive to my computer and I am using it do dual-boot Linux (Ubuntu 12.04) with Windows 7. Both hard drives are SATA. I am using the default grub bootloader on my second hard drive. The windows drive is unmodified. To get to grub, I changed the hard disk boot priority in my BIOS (P35-DS3L) to boot from the second drive. The problem I'm having is that when I boot to Windows 7 (on sda) from grub (on sdb), Windows 7 will not go to sleep (from the start menu). The display shuts off momentarily as if its going to sleep, then comes back on and displays the switch-user screen. Powercfg -lastwake does not show anything. I am sure that this is related to booting from grub on sdb because when I change the hard disk boot priority in the BIOS to boot from my (unmodified) Windows hard disk, the computer goes to sleep fine. It occurred to me that installing grub on sda might solve the problem, but I'd rather not since I like to have my windows hard disk unmodified so that booting to it from the BIOS boots directly to windows. A possible work around is to use the BIOS as a bootloader, by pressing F8 to select the boot device. Still, I'd like to know why the problem is happening in the first place.

  Read the article

• How can I remotely tell what brand/model internal SCSI card is installed in a machine?

  - by edmicman

  I am doing some consulting work for a previous employer upgrading and migrating old servers to new hardware. There is an existing file server (HP ProLiant DL380) that has an tape backup drive connected; it is using a SCSI interface and I'm pretty sure it's using an internal SCSI card. They are upgrading to a new server hardware (HP ProLiant DL160 G6). The old server is 2U, the new one 1U and we would want to move the tape drive to the new server, too. I'm trying to figure out if the SCSI card in the old server would be able to be installed in the new one or if we'll need to source a new card; mostly I don't know for sure the height of the card and if it's low-profile enough that it would fit in the new server. There is not much of a technical resource onsite and the old server is in-use anyway so I would like to avoid making a trip in myself or trying to have someone onsite pop open the case and tell me what card is there. It's running Windows Server 2003 - is there a way to tell from say Device Manager what make and model the SCSI card might be? Or any other system diagnostic program or something that would give me hardware info like that? Thanks for any info!

  Read the article

• needing storage integrity (write/read) test - for BASH

  - by Mr. Bash

  In need of shell scripts / bash commands to verify data integrity of local harddrives, usb-drives, etc, ... Like the famous www.heise.de/download/h2testw; or something that is at least common within repositories. (h2testw writes a specific datastring over and over onto the medium, then reads it again to verify if it was written correctly and displays write/read time/speed.) please no dd if=/dev/random of=/dev/sdx bs=1k && dd if=/dev/sdx of=/dev/null bs=1k since it won't verify if everything was written correctly. It is only a test if read/write is successful to the device. So far, I'm not too happy with badblocks -w -v /dev/sdx1 either, since it seems rather slow and I don't know what it exactly writes, and if it considers wear-leveling on flash media. There is also a program named F3 http://oss.digirati.com.br/f3/ that needs to be compiled. Designed after h2testw, the concept sounds interesting, i'd just rather have it as a ready to go bash script.

  Read the article

• Best option for storage clustering

  - by sam

  I'm working on an application that requires a large amount of storage space and I want to handle storage 'in-house' (Much cheaper than, say, S3) so we will have multiple servers (Initially 4) with large amounts of storage (6TB each). The storage will need to be very flexible and configurable, each piece of data should be replicated on at least 2 servers and must be easily readable/writable from ether an API of a UNIX device/file/folder like a normal drive, I don't mind which. We must also be able to easily offload content to our HTTP CDN (Edgecast), it doesn't need to have built in HTTP support but if it doesn't I'm going to have to write something to get the files onto HTTP so they can be pulled by the CDN. I've looked at a lot of solutions including Eucalyptus Walrus OpenStack Object Storage MogileFS and some others which I can't remember All the servers will be running RHEL 6, they have 4x1.5TB drives which will be RAID1'd into a single partition. All the servers have 1GB/s connections between them and 100MB/s connections to the internet with unlimited bandwidth. They have 2x2.66ghz processors. I understand there isn't a single, perfect answer but it would be nice to get some pointers.

  Read the article

• Enabling AHCI in BIOS for SSD

  - by Robert

  I am trying to help a friend with a desktop upgrade. It is an old machine with an Intel DG31 main board. The board has 1 IDE port to which a DVD-ROM drive is connected, and 2 SATA ports. 1 SATA port had a hard drive with XP on it. I have made that the secondary drive now and wiped the OS as requested, so it is just for data. The new SSD has been installed but I read that for best results one must enable AHCI in the BIOS? So I checked and in the BIOS there is a SATA Mode setting with 2 options - Native and Legacy. I think Native means AHCI? After setting to Native, I installed Windows 7 Home Premium and all the latest drivers from Intel's website and all Windows Updates. Now when I check Device Manager I see this: Also Microsoft says HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msahci\Start and HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\IastorV\Start should have value 0 for AHCI but I see that the value is 3 for both. So does this mean that Native mode is not AHCI? Or Windows 7 ignored BIOS setting and installed in IDE mode, maybe because both cables are present? Please help me enable AHCI on this system. Thanks!

  Read the article

• Squid Authentication & streaming

  - by Steve Butler

  I've got squid setup using Kerberos authentication. I'm also using squidguard as an URL redirector to block out the usual nastiness of the web. There are some sites though that we allow certain users to, and others not. This all works well, assuming I'm not using any streaming. From what i can determine from the squid logs and the wireshark traces I've done, when the initial request to stream is sent, everything is good, the authenticated username is sent with the request to squidguard. The problem is that on subsequent traffic the username is not sent to squidguard, causing it to be blocked based on default policy. I've tried using the squid built-in allow/deny stuff, but its relatively clunky, and so far squidguard has been pretty easy and fast. Here comes the question(s): How do i get Squid to pass username on all requests? (something tells me this isn't the best way) How do i get squidguard to see traffic is authenticated to a specific user even when a username isn't passed? Is there any other way of accomplishing this? A few details that may be of importance: I'm using a list of users stored in a text file for squidguard to compare against. I'm using full kerberos auth with Squid. CentOS 6.0 Squid 3.1.4 Squidguard 1.3

  Read the article

• Keyboard's media keys are blocked by a program

  - by Mike Hanson

  I've got a Microsoft Natural Ergonomic Keyboard 4000. In addition to the regular keys, it's also got keys for Web/Home, Search, Mail, Favorites (5), Calculator, and Media functions (Mute, Volume Up/Down, and Play/Pause). Everything works most of the time, and the exception is rather odd. I use a programming system called Clarion. When that has focus, the Media keys don't work. (All the others still do.) I've also discovered that programs that I create using Clarion also block the media keys (only when they have focus). This indicates that it's probably something in Clarion's Run-Time Library (RTL) that's causing the trouble. The keys will work if I click on a non-Clarion window before hitting the media key, but that's an undesirable hassle. The odd thing is that I have many colleagues with the same keyboard, and they have no problem. When I recently upgraded from Vista Professional to Win7 Ultimate, I noticed that various things "appear" differently. For example, with my old system, when I changed the volume or muted the volume bar visualization always appeared at the bottom right on the screen. Now it doesn't appear in certain programs, even when it works. This indicates an order of precedence for visual elements. I'm fairly certain a similar order of precedence exists for keyboard hooks. Depending on how the hooks are defined, and the order in which they're applied, it would seem that sometimes the IntelliType drivers don't see the media keystrokes. The Media keys probably behave differently than the rest of the "special" keys, because they are more of a standard across all keyboards, so perhaps are handled by a different driver hooking mechanism. Does anyone have any suggestions of how I might fix this problem? Is there some way to change the order of hooks? Delay the loading of the IntelliType driver? Thanks in advance!

  Read the article

• How to prevent blocking http auth popups on firefox restart with many tabs open

  - by Glen S. Dalton

  I am using the latest firefox with tab mix plus and tabgoups manager. I have maybe 50 or 100 tabs oben in different tab groups. When I shutdown firefox and start it again all tabs and tab groups are perfectly rebuilt. But I have also many pages open that are behind a standard http auth, and these pages all request their usernames and passwords. So during startup firefox pops up all these pages' http auth windows. And they block everything else in firefox, they are like modal windows. (I am involved in website development and the beta versions are behind apache http auth.) I have to click many times the OK button in the popups, before I can do anything. All the usernames and passwords are already filled in. (And the firefox taskbar entry blinks and the firefox window heading also blinks, and focus switches back and foth, which also annoys me. And sometimes the popups do not react to my clicks, because firefox is maybe just switching focus somewhere else. This is the worst.) I want a plugin or some way to skip those popups. There are some plugins I tried some time ago, but they did not do what I need, because they require a mouse click for each login, which is no improvement over the situation like it already is. This is not about password storage (because firefox already stores them). But of course, if some password storing plugin could heal this it would be great.

  Read the article

• Cheapest iSCSI SAN for Windows 2008/SQL Server clustering?

  - by MichaelGG

  Are there any production-quality iSCSI SANs suitable for use with Windows Server 2008/SQL Server for failover clustering? So far, I've only seen Dell's MD3000i, and HP's MSA 2000 (2012i), which both are around $6K with a minimal disk configuration. Buffalo (yea, I know), has a $1000 device with iSCSI support, but they say it will not work for 2008 failover clustering. I'm interested in seeing something suitable for failover in a production environment, but with very low IO requirements. (Clustering, say, a 30GB DB.) As for using software: On Windows, StarWind seems to have a great solution. But it's actually more money than buying a hardware SAN. (As I understand, only the enterprise edition supports having replicas, and that's $3000 a license.) I was thinking I could use Linux, something like DRBD + an iSCSI target would be fine. However, I haven't seen any free or low-cost iSCSI software that supports SCSI-3 persistent reservations, which Windows 2008 needs for failover clustering. I know $6K isn't much at all, just curious to see if there are practical cheaper solutions out there. And finally, yes, the software is expensive, but many small business get MS BizSpark, so the Windows 2008 Enterprise / SQL 2008 licenses are completely free.

  Read the article

• Cannot Install Bootcamp on Mac Fusion Drive

  - by user3377019

  I have two drive installed in my mid-2013 Macbook pro. It is running osx maverick. I set the two drives (an ssd and a regular HD) up using the fusion drive (following the diy fusion drive guides out there). I went ahead and created a 40gb partition to host my windows install. I removed the SSD, installed windows, then reinstalled the SSD. As soon as the ssd was placed back in the bootcamp partition stopped booting. I get a blinking cursor on a black screen. I checked out the partition info in disk utility and it appears that the windows partition is not marked bootable. Below is some info I managed to gather. I am wondering if there is a way to fix the partition table so my bootcamp will boot. /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *120.0 GB disk0 1: EFI EFI 209.7 MB disk0s1 2: Apple_CoreStorage 119.7 GB disk0s2 3: Apple_Boot Boot OS X 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.1 GB disk1 1: EFI EFI 209.7 MB disk1s1 2: Microsoft Basic Data BOOTCAMP 40.0 GB disk1s2 3: Apple_CoreStorage 459.2 GB disk1s3 4: Apple_Boot Boot OS X 650.0 MB disk1s4 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Macintosh HD *573.4 GB disk2 Name : BOOTCAMP Type : Partition Disk Identifier : disk1s2 Mount Point : /Volumes/BOOTCAMP File System : Windows NT File System (NTFS) Connection Bus : SATA Device Tree : IODeviceTree:/PCI0@0/SATA@1F,2/PRT1@1/PMP@0 Writable : No Universal Unique Identifier : 584BAED6-4C46-4F18-93B3-957F6E27003C Capacity : 40 GB (39,998,980,096 Bytes) Free Space : 16.34 GB (16,339,972,096 Bytes) Used : 23.66 GB (23,659,003,904 Bytes) Number of Files : 86,424 Number of Folders : 0 Owners Enabled : No Can Turn Owners Off : No Can Be Formatted : No Bootable : No Supports Journaling : No Journaled : No Disk Number : 1 Partition Number : 2

  Read the article

• Fast Ethernet module for Cisco 2620

  - by Kenny Rasschaert

  I have a Cisco 2620 Router. It comes with one fast ethernet port built in (circled in red), and one old AUI ethernet module is installed (circled in blue). I figure I can put a transceiver on the AUI interface to get a second RJ45 connector. What I'd really like to have is a second fast ethernet connector. The ideal candidate to achieve this would be the NM-1FE-TX module. Cisco claims on their website that this module is not suitable for the Cisco 2620 and Cisco 2620XM. It says so in "Table 2 Physical Limitation of Serial Modules per Chassis". Indeed, this module was designed for the 3600 series of routers. I've seen claims on the internet, however, of people having this module on a 2620XM, and it being fully functional. This claim gains some credibility because of the fact that in Cisco's own Packet Tracer software, you can install this module on the 2620XM router. I'm looking for a definitive answer. Will this module work on a Cisco 2620? Is there perhaps another way to get a second fast ethernet port on this device?

  Read the article

• Change the number of consecutive frequent ssh login before temporary blocking the user login

  - by Kenneth

  my server currently would temporarily refuse a user to login for certain amount of time (maybe ~20min) if the user consecutively frequent ssh login for 3 times. Can I change this behaviour (say relaxed the definition of frequent maybe from 'within 5 sec' to 'within 10 sec'; or increase the # of consecutive login from 3 to 5)? Thanks. Added: Ah.. now I think the problem was not with the ssh. I just tried on another newly installed server. consecutive successful login won't block the user. I have no sudo permission on the server I mentioned above. Now I suspect this behaviour may cause by the firewall in the system. Thanks everyone's comments. ADDED 2: Ah... after some searches. I think the server is using /sbin/iptables to do it as I can see the iptables program is there even though I don't have permission to list the rules. Thanks everyone, special thank to jaume and Mark!

  Read the article

< Previous Page | 530 531 532 533 534 535 536 537 538 539 540 541  | Next Page >