Search Results

Search found 18729 results on 750 pages for 'edit'.

Page 535/750 | < Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >

• How to configure a large mtu (linux)

  - by Somejan

  I have a gigabit ethernet connection from my laptop to my router, and a working ipv6 connection to the internet. I can receive very large packets from sites on the internet, with sizes up to at least 10000 bytes (according to wireshark). (edit: turns out to be linux's 'generic receive offload') However, when trying to send anything, my local computer fragments at just below 1500 bytes for ipv6. (On ipv4, I can send tcp packets to the internet of at least 1514 bytes, I can ping with packets up to the configured mtu of 6128 but they are blackholed.) I'm on ubuntu 12.04. I have configured an mtu for my eth0 of 6128 (the maximum it accepts), both using ip link set dev eth0 mtu 6128 and in the NetworkManager applet gui, and restarted the connection. ip link show eth0 shows the 6128 mtu is indeed set. ip -6 route shows that none of the paths the kernel knows about have an mtu set. I can ping over ipv4 with packets up to 6128 bytes (though I don't get responses), but when I do ping6 myrouter -c3 -s1500 -Mdo I get error replies from my own computer saying that the packets are too large and the mtu is 1480. I have confirmed with Wireshark that nothing is put on the wire, and the replies are indeed generated by my own computer. So, how do I get my computer to use the larger mtu?

  Read the article

• What is the difference between a PDU and a power strip (both 120V, 15A)?

  - by rob

  I just chatted with an APC rep about upgrading the UPSes at our office. She recommended a single higher-capacity 6-outlet Smart-UPS to replace the four Back-UPS units we currently have. When I asked how she recommended plugging in all the current devices, she recommended using a APC's AP9567 PDU, but said not to use a power strip. At first she said I had to use an APC brand PDU, but after I inquired about using a Tripp-Lite PDU, she said any brand PDU would be fine. The APC PDU previously referenced looks like a standard 120V power strip with overload protection but no surge protection. Other than overload protection (which seems redundant if plugging into the UPS), is there something else I'm missing, or should any power strip (without surge protection) be fine? Edit: I didn't mention it earlier, but we don't have a proper rack--though I did still plan to mount the PDU or power strip to something. I guess I'm wondering if there's any special reason I should pay as much as $180 for the low-end APC PDU (which just looks like a power strip to me) vs. $20-$30 for a workbench power strip.

  Read the article

• Thunderbird 11.0.1 and Lightning 1.3: How do I propose a different time for a meeting?

  - by seaao

  This all happens on my x64 Linux workstation btw. tl;dr: My colleague invited some people and me for a meeting. The meeting was scheduled a week to late. I -wrongfully- accepted. How do I propose a new time? To explain a bit more in detail: I received a meeting request in my mailbox. Thunderbird is so nice to let me accept or reject it, and after I click the button to accept, it is directly added to my calendar. But when I double click on the meeting to edit it, I get a function-wise scaled-down version of the meeting: The only settings I can alter are whether I want reminders, and if I go at all. Trying to drag it to another day doesn't work either: My calendar behaves like read-only (which it isn't btw). There are several questions (without answer...) to be found on Stack Overflow and on the Thunderbird knowledge base about using lightning. But I get the idea that I'm one of the few who won't comply with the team even before the meeting is started. My googling revealed no bugs or feature requests in the direction I'm thinking. A link to an explanation how to achieve this, or another perspective about how to reach the desired goal (meeting with my colleagues and me) would be mostly welcome!

  Read the article

• Run a script on user connection on the VM host

  - by Scott Chamberlain

  I have a server running a Virtual Desktop Managed Pool, what I would like to do is when a user logs in I would like a script to check the number of available VMs and if below a threashold add additional VMs to the pool. The script to check the load and add to the pool is not the problem, I have that already figured out: $collectionName = "Test1"; $rdvh = "vmHost.example.com"; $minAvailableVMs = 2; Import-Module RemoteDesktop; $pool = Get-VirtualDesktopCollection -CollectionName $collectionName; $availableVMs = $pool.Size - ($pool.Size * $pool.PercentInUse / 100); $status = Get-VirtualDesktopCollectionJobStatus $collectionName #only add new servers if we are below the threashold and in the JOB_COMPLETEED state if($availableVMs -lt $minAvailableVMs -and $status.Status -eq [Microsoft.RemoteDesktopServices.Management.VirtualDesktopCollectionJobStatus]::JOB_COMPLETED) { Add-RDVirtualDesktopToCollection -CollectionName $collectionName -VirtualDesktopAllocation @{"$rdvh" = 1} } The problem I am having is, how do I run the above script on the Virtualization Host/Connection Broker/Some other server when a user connects?. I don't think it would be appropriate to run this as a logon script inside the VM, I think there is a way to do this on the management side but I don't know the new scripting interface in Server 2012 R2 well enough to know which commandlets I should look for to schedule this. EDIT: I know System Center is perfect for this but I do not have a license and was denied when I asked for it to be added to the budget.

  Read the article

• Copying windows home server backup offsite

  - by Simon

  What ways are there to copy a windows home server backup to an offsite location? I'm talking specifically (and only) about the automated backup of my entire machine, and not the shared network folders. I am 90% working away from home on my laptop which has a 640GB drive so the shared folders are essentially useless to me. I backup every night, but if my house burns down or broken into the I'm in serious serious trouble ! I'm really looking for some alternative way to back up my entire machine - which much not interfere with the reliability or speed by which my WHS backs up my laptop every night. Either a way to 'export' a complete machine backup from the server, or recommendations on non-conflicting software I can backup to a 1TB drive at work are what I'm looking for. Note: I believe that WHS uses its own completely proprietary backup and doesn't use things like any 'backup bit' or 'archive bit'. I just dont want to install some other backup software that will conflict. PS I'm now running Windows 7 and just realized that I should probably check out the backup functionality it gives me. I assume that won't conflict right! Edit: Thanks for the hosted solutions. I'd also appreciate ways to backup to an 'offsite' location that I control - like my office vs. my home. The hosted solutions I think will be too slow or expensive for my needs.

  Read the article

• Intermittently uncommunicative subnets

  - by mhd

  Last week proved me a veritable Cassandra: I've always said that it's a bad idea to have only one firewall/router, without a backup or failover. And thus our Cisco PIX went haywire, refusing to route properly. And of course, the only one available here on short notice is me, and while I'm quite grounded in Linux, I'm really a developer not a sysadmin (the fact that this hit me on sysadmin appreciation day is a bit ironic). Anyway, this weekend I tried to hack up a temporary solution: I used an old server with enough NICs (two built-in, four on a card) to serve as a gateway and firewall. Due to some problems with the raid controller, I got only two router distros running, and between Untangle and Ebox I decided for the latter. Now everything is quite okay. I've got all the different subnets we've got here (all with separate switches) talking to each other and even to the internet (Cisco 2800 router, T1 lines). But from time to time (20-60 minute intervals), I get a total routing failure. Our main, office subnet can't talk to our server subnet and can't connect to the internet. This is not the end of a gradual slowdown, either everything's working perfectly or I get a total lack of communication for about two minutes each time. Now I'm a bit at wits end what to check. At least with the default EBox setup, nothing in /var/log shows anything weird and it doesn't exactly have lots of built-in monitoring tools. So I'm hoping someone here could give me some pointers about what to look out for. I did change the ethernet cable from the office switch to the firewall, with no results. I might change switches, although within the switch it seems to work ok enough. Edit: I'm not sure whether this is the sole cause of the problem, but after I noticed a few DHCP entries just before the last drop of connectivity, I tried to reproduce that. And alas, whenever I renew a DHCP connection, I can't access other subnets anymore. Running ISC DHCPD 3.0.6.

  Read the article

• SQL Server Instance login issue

  - by reallyJim

  I've just brought up a new installation of SQL Server 2008. I installed the default instance as well as one named instance. I'm having a problem connecting to the named instance from anywhere besides the server itself with any user besides 'sa'. I am running in mixed mode. I have a login/user that has a known username. Using that user/login, I can properly connect when directly on the server. When I attempt to login from anywhere else, I recieve a "Login failed for user ''", with Error 18456. In the log file in the server, I see a reason that doesn't seem to help: "Reason: Could not find a login matching the name provided.". However, that user/login DOES exist, as I can use it locally. There are no further details about the error. Where can I start to find something to help me with this? I've tried deleting and recreating the user, as well as just creating a new one from scratch--same result, locally fine, remotely an error. EDIT: Partially Resolved. I'm now passed the base issue--the clients were trying to connect via the default instance. I don't know why. So, once proper ports were opened in the firewall, and a static port assigned to the named instance, I can now connect--BUT ONLY if I specify the connection as Server,Port. SQLBrowser is apparently not helping/working in this case. I've verified it IS running, and done a stop/restart after my config changes, but no difference yet.

  Read the article

• Firefox: Unload a tab manually

  - by unor

  Firefox has a setting "Don't load tabs until selected" (see How do I make Firefox 13 Load All My Tabs on Startup or when Resuming Reload). I like that behaviour. I am searching for a way to "deload"/deactivate a tab manually for a session (until I reload it). It should stop all running JavaScript functions and plugins (like Flash). The whole webpage content may disappear until I reload/re-activate the tab, but that is not a requirement. The title has to be displayed as tab label (like it is the case with the startup setting, too). The workaround would be to restart Firefox and don't switch to the tab I want to be deactivated. This is pretty annoying, of course. EDIT: Here is what I found so far (thanks, @bytebuster!) BarTab no longer being maintained (see why) BarTab Lite seems to miss this functionality from BarTab Dormancy experimental; comes with warning that it "may eat your session" Tab Mix Plus Feature request: Unload Tab feature Tab Utilites seems to offer this functionality only for automatic unloading Feature request: Add "unload tab" to tab context menu. UnloadTab removed from addons.mozilla.org (who knows why)

  Read the article

• Best way to build / implement a corporate developer Linux distro with multiple kernels?

  - by Garen

  At work we have Linux users who understandably prefer using Ubuntu. Problem is, we also have developer tools that only work with 'officially' supported Linux distributions that use much older 2.6.18 based kernels. (And even if they worked with newer ones, the vendors could always say they won't "support" the software unless it's on one of their 'officially' supported platforms.) We could of course just tell them to use CentOS or something else 2.6.18-based, and I'm sure their response would be something like: "you can take Ubuntu from our cold, dead hands." :) Which brings to me some questions--is there any good/easy/recommended way to run something like Ubuntu as a host VM and Centos 5.x as a guest OS (with which system--Xen,KVM,VMWare, ...?), and then roll that into our own custom internal distribution that could be easily installed? KVM looks like a good high-performance option just recently included in RHEL 5.4, but if hardware support for virtualization like Intel-VT or AMD-V is necessary, then I'd guess only those folks with fairly new PCs will be able to do it. Would be very interested to hear how anyone else has addressed this kind issue. EDIT: The target audience / users of this kind of system would be developers, each one needs to run locally licensed commercial software, so building out some separate beefy central machines isn't an option unfortunately due to license restrictions. Even if that weren't the case, a couple developers could quickly eat up the resources with parallel builds. :) Ideally, I was hoping there was some step-by-step guide out there to build your own pre-built distribution that had e.g. CentOS 5.x and Ubuntu Desktop as a guest.

  Read the article

• How to prevent asymmetric routing with multiple eBGP routers?

  - by Andy Shinn

  I have 2 routers announcing a /22 subnet to different providers (one providers connects to each of the 2 routers). I have split the /22 in two /23 to announce one /23 on each of the routers plus the /22 (the providers will take the more specific route). This allows me to fail over and keep traffic inside the /23 in and out the same provider. What are other ways in which I could announce just the /22 with both routers and have packets from servers on the network behind the routers go back out the same router in which they came in from? EDIT: The main problem I come across, which end users and clients complain about the most, is that the least hop route is sometimes not the "optimal" route. In my case, I know that Provider B may have better latency to X nation. But when packets come in from provider B, they may go out Provider A or provider B. The reverse is also true. If I send a packet to X nation out provider A, even though it may have more hops back, the packet will likely come in from Provider B (which may have higher latency, packet loss, etc. to this nation)

  Read the article

• ProCurve ACL to prevent a subnet from leaving the switch

  - by kce

  I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

  Read the article

• Looking for a real DisplayPort hub/splitter

  - by squircle

  In my search for a new display, I came across the Dell Multi-Monitor Hub MMH11, which seemed to be an alternative to my search for daisy-chainable DisplayPort displays. However, before I cave and spend $179 on this device, I am wondering if this will be similar to other splitting devices where it appears to the computer as one big monitor and the device does the splitting (which I don't want). Or, does this use the packet-based nature of DisplayPort to present two/three separate displays to the computer? Also, would this device work on my MacBook Pro? (I know the Dell site says it's for Windows, but it also says that no driver installation is required. I'd assume since the MBP supports DP 1.2 it would work, but it's better to ask). Thanks! Edit: I've checked out the similar-looking Cirago DisplayPort splitter, but I have extreme doubts as to whether or not it's a genuine displayport splitter, or just another monitor-conglomerate. Their DVI solution looks identical to Dell's, which I'm pretty sure won't do what I want. I also don't want to order this DisplayPort "hub" and find that it doesn't do what I want it to.

  Read the article

• Mount an VHD on Mac OS X

  - by janm

  Is it possible (how) to mount an VHD file created by Windows 7 in OS X? I found some information about how to do this on linux. There is a fuse fs "vdfuse" which uses virtualbox libs to mount filesystems supported by virtualbox. However I was unable to compile the package on osx because nearly all headers are missing and I doubt that it would work anyway... EDIT #2: Okay I got my hands dirty and finally compiled vdfuse (http://forums.virtualbox.org/viewtopic.php?f=26&t=33355&start=0) on osx. As a starting point I used macfuse (http://code.google.com/p/macfuse/) and looked at the example file systems. This led me to the following build script infile=vdfuse.c outfile=vdfuse incdir="your/path/to/vbox/headers" INSTALL_DIR="/Applications/VirtualBox.app/Contents/MacOS" CFLAGS="-pipe" gcc -arch i386 "${infile}" \ "${INSTALL_DIR}"/VBoxDD.dylib \ "${INSTALL_DIR}"/VBoxDDU.dylib \ "${INSTALL_DIR}"/VBoxVMM.dylib \ "${INSTALL_DIR}"/VBoxRT.dylib \ "${INSTALL_DIR}"/VBoxDD2.dylib \ "${INSTALL_DIR}"/VBoxREM.dylib \ -o "${outfile}" \ -I"${incdir}" -I"/usr/local/include/fuse" \ -Wl,-rpath,"${INSTALL_DIR}" \ -lfuse_ino64 \ -Wall ${CFLAGS} You actually don't need to compile VirtualBox on your machine, just install a recent version of VirtualBox. So now I can partially mount vhds. The separate partitions appear as block files Partition1, Partition2, ... on my mount point. However Mac OS X does not include a loopback file system and macfuse's loopback fs does not work with block files, so we need a loopback fs to mount the blockfiles as actual partitions.

  Read the article

• VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

  - by Dayton Brown

  I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

  Read the article

• Patch management on multiple systems

  - by Pierre

  I'm in charge of auditing the security configuration of an important farm of Unix servers. So far, I came up with a way to assess the basic configuration but not the installed updates. The very problem here is that I just can't trust the package management tools on those machine. Indeed some of them did not sync with the repository for a long time (So I can't do a "yum check-updates" on Redhat for example). Some of those servers are not even connected to the internet and use an company repository. Another problem is that I have multiple target systems: AIX, Debian, Centos/Redhat, etc... So the version could be different (AIX) and the tools available will be different. And, last but not least, I can't install anything on the target system. So I need to use a script to retrieve the information and either: process it directly or save the information to be able to process it later on a server (Which may happen to run a different distribution than the one on which the information have been retrieved). The best ideas I could come up with were: either retrieve the list of installed packages on the machine (dpkg -l for example on debian) and process it on a dedicated server (Directly parsing the "Packages" file of debian repositories). Still, the problem remains the same for AIX and Redhat... or use Nessus' scripts to assess vulnerability on the installed packages, but I find this a bit dirty. Does anyone know any better/efficient way of doing this ? P.S: I already took time to review some answers to similar problems. Unfortunately Chef, puppet, ... don't meet the requirements I have to meet. Edit: Long story short. I need to have the list of missing updates on a Unix system just like MBSA on Windows. I'm not authorized to install anything on this system as it's not mine. All I have are scripts languages. Thanks.

  Read the article

• Mac updated just now, postgres now broken

  - by user52224

  I run postgres 9.1 / ruby 1.9.2 / rails 3.1.0 on a maxbook air for local dev. It's all been running smoothly for months, (though this is the first time I've done development on a mac.) It's a macbook air from last year, and today I got the mac osx software update message as I have a few times before, and my system downloaded approx 450mb of updates and restarted. It now says it's on OSX 10.7.3. Point is, postgres has stopped working, when I start my thin server (mirror heroku cedar) as normal, and then browse to my rails app I get: PG::Error could not connect to server: Permission denied Is the server running locally and accepting connections on Unix domain socket "/var/pgsql_socket/.s.PGSQL.5432"? What happened? After browsing around a few questions I'm still confused, but here's some extra info: Running psql from command line gives same error I can run pgadmin 3 and connect via it and run SQL no problems Running which psql shows the version as /usr/bin/psql I created a PostgreSQL user back when I got the mac (it's always been on lion) I've no idea why, almost certainly I was following a tutorial which I neglected to store in my notes. Point is I am aware there is a _postgres user as well. I know it's rubbish, but apart from a note on passwords, I don't have any extra info on how I configured postgres - though the obvious implication is that I did not use the _postgres user. Anyone have suggestions or information on what might have changed / what I can try to debug and fix? Thanks. Edit: Playing around based on this question and answer: http://stackoverflow.com/questions/7975414/check-status-of-postgresql-server-mac-os-x, see this string of commands: $ sudo su postgreSQL bash-3.2$ /Library/PostgreSQL/9.1/bin/pg_ctl start -D /Library/PostgreSQL/9.1/data pg_ctl: another server might be running; trying to start server anyway server starting bash-3.2$ 2012-04-08 19:03:39 GMT FATAL: lock file "postmaster.pid" already exists 2012-04-08 19:03:39 GMT HINT: Is another postmaster (PID 68) running in data directory "/Library/PostgreSQL/9.1/data"? bash-3.2$ exit

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  Hello, I'm having some problems installing CentOS 5.5 Final (i386) Onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up ans gives you the option on how to boot into the DVD, Ill press enter to go into the graphical installer. The Screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours.) I then booted into it again and tried using Linux Text thinking it was a problem with graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point i think its a hardware problem. The Server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) Configured for RAID 0. ( Also there is a option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. ================Edit================== ooshro, typing "text" doesn't change a thing. still stuck at the blinking cursor. I looked it up and its really the same thing as typing "linux text", which as stated in the first part of my question, i've already done.

  Read the article

• Upgraded users to Win7. Now getting "path not found" when saving files or opening attachments

  - by Matt Penner

  We have a Server 2008 AD environment with about 5k users. We just rolled out Windows 7 SP1 (were XP) with great success. However, about once a day we get a few calls that a user opens a file from their Documents (the folder is on the server and redirected), edits it and attempts to save but Win7 reports that the path is not found either because it doesn't exist or no permissions. The only way to fix it is to delete the profile. In addition we get about the same number but different users saying that they cannot open attachments from Outlook 2010 due to no permission. We have to edit the temp Outlook storage path in the registry to fix it (or delete the profile). I think the two issues may be related. What scares us is that we rolled out 1 month ago and had no calls of this nature until about 2 weeks ago. It started off as one or two but seems to be growing. Any ideas? We're going to open a Microsoft ticket but I wanted to seenif anyone else has run into this. Thanks!

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

• Multiple servers vs 1 big server performace

  - by pistacchio

  Hi to all! My team of developers has suggested a server structure for an upcoming project we are developing. Our structure is "logical", meaning that the various logical components of the application (it is a distributed one) relies on different servers. Some components are more critical than others and will be subjected to more load. Our proposal was to have 1 server per component but the hardware guys suggested to replace the various machines with a single, bigger one with virtual servers. They're gonna use Blade Servers. Now, I'm not an expert at all, but my question to the guys was: so if we need, for example, 3 2GHz CPU / 2GB RAM machines and you give me 1 machine with 3 2GHz CPUs and 6 GB of RAM it is the same? They told me it is. Is this accurate? What are the advantages or disadvantages of both the solutions? What are the generally accepted best practices? Could you point out some URL reference dealing with the problem? Thank you in advance! EDIT: Some more info. The (internet / intranet) application is already layered. We have some servers on the DMZ that will expose pages to the internet and the databases are on their own machines. What we want to split (and they want to join) are some webservers that mainly expose webservices. One is a DAL that communicates with the database layer, one is our Single Sign On / User Profile application that gets called once per page and one is a clone of what seen on the Internet to be used on our lan.

  Read the article

• Synchronize two directories on linux pc

  - by Gab

  I need a distributed filesystem (or a synchronization tool) that is capable of keeping a directory synchronized across 4 pc. My requirements are: offline access (data must be available offline on each pc) preserve execution rights: some files are marked executable on a linux partition. This flag should be replicated. efficient sync strategy: some of my files are 20GB, they are changed quite often, but in very little parts (Virtualbox images). Delta transmissions are welcome. efficient handling of space: no history for files, files shouldn't be copied to temp directories "just in case you break it". it must propagate deletions of files modification can happen in any of the 4 pcs, they should be propagated when other pc are connected. Other specs of my solution are: Sync is over a lan, the total amount of data to be synced is around 180GB, in some ten thousand files. Changes are small, but can happen in big files. At the moment i'm interested in a linux only solution. conflicts either don't happen or are solved with "last one wins" I haven't found any good solution. I've been trying: unison: it is the only one working at the moment, but during the hashing phase it hangs my pc for some minute, disk light steady on. Sparkleshare doesn't handle large files nicely. It keeps an history of all your changes that grows up indefinitely. They promise it will be fixed in next releases, but at the moment it still doesn't fit my needs. owncloud (keeps history of each file i change) coda ? (help! i couldn't set it up correctly!) git-annex assistant transforms all your files in symlinks and mark the original file as read only ("just in case you make a mistake while you modify it"!). Before you edit a file you have to issue a special command "git-annex unlock", that creates a local copy of the file, and you have to remember to lock it again if you want it synchronized. What to try next?

  Read the article

• Windows 7 Busy Icon won't stop spinning

  - by Lynda

  In windows 7 you have the busy icon that is a little blue wheel spinning beside the cursor when it is doing something. It has started to spin for about a second every 3-5 seconds. There is noting running that I can tell on the computer to cause the busy icon. It gets very annoying and I am not sure what to do to get it to stop. Ideas? Running a CPU Usage Gadget says I have less than 5% of the CPU being use and I have over 6GB of RAM free. (I have 8GB total) I am running a 3.6 GHZ AMD FX 4100 processor. EDIT- What I am actually seeing is the working in background pointer (the pointer is still visible beside the busy icon). EDIT 2 - After realizing this happened with the printer installation I turned on the the printer and the busy icon stopped. The printer is setup wirelessly. How do I stop Windows from (I guess) checking for the printer? That is what I assume it is doing. I am using a HP Officejet 8600

  Read the article

• Creating security permissions for a non-domain-member user in Windows Server 2008

  - by Overhed

  Hello everyone, I apologize in advance for incorrect use of terminology, as I'm not an IT person by trade. I'm doing some remote work via a VPN for a client and I need to add some DCOM Service security permissions for my remote user. Even though I'm on the VPN, the request for access to the DCOM service is using my PCs native user (and since I'm running Vista Home Premium it looks something like: PC-NAME\Username). The request for access comes back with access denied and I can not add this user to the security permissions as it "is not from a domain listed in the Select Location dialog box, and is therefore not valid". I'm pretty stuck and have no clue what kind of steps I need to do here. Any help would be appreciated, thanks in advance. EDIT: I have no control over what credentials are being passed in to the server by my computer. This scenario is occurring in an installation wizard that has a section which requests you point it to the machine running the "server" version of the software I'm installing (it then tries to invoke the relevant COM service, but my user does not have "Remove Activation Permissions" on that service, so I get request denied).

  Read the article

• Certificate revocation check fails for non-domain guest in spite of accessible CRL

  - by 0xFE

  When we try to use certificates on computers that are not part of the domain, Windows complains that The revocation function was unable to check revocation because the revocation server was offline. However, if I manually open the certificate and check the CRL Distribution Point property, I see an ldap:/// URL and an http:// URL that points to externally-accessible IIS site that hosts the CRLs. Of course, the non-domain-joined client cannot access the ldap:/// URL, but it can download the CRL from the http:// link (at least in a browser). I enabled CAPI logging and I see the event that corresponds to this failed revocation check. The RevocationInfo section is: RevocationInfo [ freshnessTime] PT11H27M4S RevocationResult The revocation function was unable to check revocation because the revocation server was offline. [ value] 80092013 CertificateRevocationList [ location] UrlCache [ url] http://the correct URL [fileRef] 6E463C2583E17C63EF9EAC4EFBF2AEAFA04794EB.crl [issuerName] the name of the CA Furthermore, I can see the HTTP request to the correct URL and the server's response (HTTP 304 Not Modified) with Microsoft Network Monitor. I ran certutil -verify -urlfetch, and it seems to show the same thing: the computer recognizes both URLs, tries both, and even though the http:// link succeeds, returns the same error. Is there a way to have non-domain-joined clients skip the ldap:/// link and only check the http:// one? Edit: The ldap:/// URL is ldap:///CN=<name of CA>,CN=<name of server that is running the CA>,CN=CDP,CN=Public Key Services,CN=Services,CN=Configuration,DC=<domain name>?certificateRevocationList?base?objectClass=cRLDistributionPoint The non-domain-joined clients may be on the domain network or on an external network. The http:// CDP is accessible from the public internet.

  Read the article

• Postgresql connection refused

  - by Jonathan

  I'm trying to remotely connect to my postgresql database. I have two virtual machines set up both running ubuntu 14.04. I am trying to connect to the second vm using the first vm using psql -h 10.0.1.23 -U postgres -d postgres But I receive the error: Could not connect to server: Connection refused Is the server running on host "10.0.1.23" and accepting TCP/IP connections on port 5432? I have changed the pg_hba.conf and added host all all 10.0.1.64/24 md5 host all all * md5 host all all 0.0.0.0/0 md5 And changed the postgresql.conf listen_address=" * " In an attempt to allow all incoming connections. I have also tried to change the firewall settings, but I am unsure of whether or not the ports are properly listening for the connection. Edit: Output of netstat -an | grep -E '^tcp[^6].*LISTEN' tcp 0 0 127.0.1.1:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:23 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:5432 0.0.0.0:* LISTEN

  Read the article

< Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >