Search Results

Search found 17754 results on 711 pages for 'field description'.

Page 535/711 | < Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >

• ESXI 5.1 - Unable to trunk to cisco switch

  - by Lance

  I have configured my esxi host vSwitch1 to use the secondary NIC on my VMware host. On vSwitch1 configuration I have set the VLAN to 4095 which specifies to allow all VLANs. If my cisco switch port configuration is set to an access port my server can ping the vlan interface on the switch. If my cisco switch port configuration is set to a trunk, whilst it stays UP UP and CDP information is available, I lose my ping from VMware VM server to the local vlan interface on the switch and I lose any server connectivity to my network. Switch NIC teaming policy to Route based on originating virtual port ID Configuration based on: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1006628 interface GigabitEthernet0/42 description Host Port switchport trunk encapsulation dot1q switchport trunk allowed vlan 18,220 switchport mode trunk switchport nonegotiate spanning-tree portfast trunk end Output from ESXI CLI esxcfg-vswitch -l: ~ # esxcfg-vswitch -l Switch Name Num Ports Used Ports Configured Ports MTU Uplinks vSwitch0 128 5 128 1500 vmnic0 PortGroup Name VLAN ID Used Ports Uplinks VM Network 4095 1 vmnic0 Management Network 4095 1 vmnic0 Switch Name Num Ports Used Ports Configured Ports MTU Uplinks vSwitch1 128 4 128 1500 vmnic1 PortGroup Name VLAN ID Used Ports Uplinks VM Network 2 4095 1 vmnic1 Any tips welcome!!!

  Read the article

• upstart config to start sync daemon as non-root user

  - by Rudiger Wolf

  I am planning to use inosync to sync data from master server to several client servers. I have created a user called rsyncuser in both master and slaves with access permissions and passwordless ssh access from master to slave servers. Inosync is working when I use it from the command line as rsyncuser. Next I want this to start automatically when server is turned on. I figured upstart is the way to get this working. I am unable to find the right upstart command to get this working. Here is my upstart conf file. The problem seems to be around running "inosync -d -c /etc/inosync/inosync_rsyncuser.py" as a given user. As you can see I have tried a number of various options! description "start inosync to sync data to other CDN Servers as rsyncuser" console output #start on startup #stop on shutdown start on (net-device-up and local-filesystems) stop on runlevel [016] #start on runlevel [2345] #stop on runlevel [!2345] #kill timeout 30 env RUN_AS_USER=rsyncuser expect fork script echo "Inosync updtart job seems to have started" /tmp/upstart.log # exec sudo -u rsyncuser -c "ls -la" /tmp/upstart.log 2&1 # LOGFILE=/var/log/logfile.`date +%Y-%m-%d`.log # exec su - $RUN_AS_USER -c "inosync -d -c /etc/inosync/inosync_rsyncuser.py" $LOGFILE 2&1 # exec su -c "ls -la" /tmp/upstart.log 2&1 # emit inosync_running end script

  Read the article

• How do I install the pdo_mysql driver on Red Hat Enterprise Linux 6.1?

  - by Will Martin

  I have a RHEL box running PHP 5.3.3, which was installed using the binary packages provided by yum. I have installed the php-pdo package: # yum info php-pdo Loaded plugins: product-id, rhnplugin, subscription-manager Updating Red Hat repositories. Installed Packages Name : php-pdo Arch : x86_64 Version : 5.3.3 Release : 3.el6_1.3 Size : 168 k Repo : installed From repo : rhel-x86_64-server-6 Summary : A database access abstraction module for PHP applications URL : http://www.php.net/ License : PHP Description : The php-pdo package contains a dynamic shared object that will add : a database access abstraction layer to PHP. This module provides : a common interface for accessing MySQL, PostgreSQL or other : databases. It appears to be working correctly for SQLite databases, but not MySQL. There's no file including pdo_mysql.so in /etc/php.d, and there is no copy of pdo_mysql.so in /usr/lib64/php/modules. I'm pretty sure I just need the driver file and a line in the PHP configuration. A yum search pdo mysql didn't turn up any useful packages, and Google has failed me. If I were on Ubuntu or Debian, I'd apt-get install php5-mysql and be done with it. So ... where in Red Hat land do I get a copy of pdo_mysql.so, and install it properly?

  Read the article

• Resolving "JBoss Web Console is Accessible to Unauthenticated Remote Users" vulnerability

  - by IAmJeff

  Our security team has determined there is a vulnerability in one of our systems. We are using version JBoss 5.1.0GA on RHEL 5.10. Vulnerability description: JBoss Web Console is Accessible to Unauthenticated Remote Users Yes, this looks familiar. Refer to Question 501417. I do not find the answer there complete. Can someone (or multiple someones) answer Does a newer version of JBoss fix this vulnerability? Are there links describing, in more detail, manual modification of JBoss configuration files to resolve the issue? Are there others options to remediate this vulnerability? Why don't I find the other answer complete? I'm not at all familiar with JBoss, so this answer seems a bit too simple. The web-console.war contains commented-out templates for basic security in its WEB-INF/web.xml as well as commented-out setup for a security domain in WEB-INF/jboss-web.xml. Just uncomment those basic security blocks and restart? Is there anything else I need to include? This seems generic. Do I need to include anything about my environment, such as absolute paths, etc.? Am I making this too complicated?

  Read the article

• How to list rpm packages/subpackages sorted by total size

  - by smci

  Looking for an easy way to postprocess rpm -q output so it reports the total size of all subpackages matching a regexp, e.g. see the aspell* example below. (Short of scripting it with Python/PERL/awk, which is the next step) (Motivation: I'm trying to remove a few Gb of unnecessary packages from a CentOS install, so I'm trying to track down things that are a) large b) unnecessary and c) not dependencies of anything useful like gnome. Ultimately I want to pipe the ouput through sort -n to what the space hogs are, before doing rpm -e) My reporting command looks like [1]: cat unwanted | xargs rpm -q --qf '%9.{size} %{name}\n' > unwanted.size and here's just one example where I'd like to see rpm's total for all aspell* subpackages: root# rpm -q --qf '%9.{size} %{name}\n' `rpm -qa | grep aspell` 1040974 aspell 16417158 aspell-es 4862676 aspell-sv 4334067 aspell-en 23329116 aspell-fr 13075210 aspell-de 39342410 aspell-it 8655094 aspell-ca 62267635 aspell-cs 16714477 aspell-da 17579484 aspell-el 10625591 aspell-no 60719347 aspell-pl 12907088 aspell-pt 8007946 aspell-nl 9425163 aspell-cy Three extra nice-to-have things: list the dependencies/depending packages of each group (so I can figure out the uninstall order) Also, if you could group them by package group, that would be totally neat. Human-readable size units like 'M'/'G' (like ls -h does). Can be done with regexp and rounding on the size field. Footnote: I'm surprised up2date and yum don't add this sort of intelligence. Ideally you would want to see a tree of group-package-subpackage, with rolled-up sizes. Footnote 2: I see yum erase aspell* does actually produce this summary - but not in a query command. [1] where unwanted.txt is a textfile of unnecessary packages obtained by diffing the output of: yum list installed | sed -e 's/\..*//g' > installed.txt diff --suppress-common-lines centos4_minimal.txt installed.txt | grep '>' and centos4_minimal.txt came from the Google doc given by that helpful blogger.

  Read the article

• Importing XML into an AWS RDS instance

  - by RoyHB

  I'm trying to load some xml into an AWS RDS (mySql) instance. The xml looks like: (it's an xml dump of the ISO-3661 codes) <?xml version="1.0" encoding="UTF-8"?> <countries> <countries name="Afghanistan" alpha-2="AF" alpha-3="AFG" country-code="004" iso_3166-2="ISO 3166-2:AF" region-code="142" sub-region-code="034"/> <countries name="Åland Islands" alpha-2="AX" alpha-3="ALA" country-code="248" iso_3166-2="ISO 3166-2:AX" region-code="150" sub-region-code="154"/> <countries name="Albania" alpha-2="AL" alpha-3="ALB" country-code="008" iso_3166-2="ISO 3166-2:AL" region-code="150" sub-region-code="039"/> <countries name="Algeria" alpha-2="DZ" alpha-3="DZA" country-code="012" iso_3166-2="ISO 3166-2:DZ" region-code="002" sub-region-code="015"/> The command that I'm running is: LOAD XML LOCAL INFILE '/var/www/ISO-3166_SMS_Country_Codes.xml' INTO TABLE `ISO-3661-codes`(`name`,`alpha-2`,`alpha-3`,`country-code`,`region-code`,`sub-region-code`); The error message I get is: ERROR 1148 (42000): The used command is not allowed with this MySQL version The infile that is referenced exists, I've selected a database before running the command and I have appropriate privileges on the database. The column names in the database table exactly match the xml field names.

  Read the article

• gpfs: adding a new nsd server to a cluster

  - by alessandra

  I have a gpfs cluster composed by 10 linux nodes, managed by a primary server A, which also act as nsd server for a first stack of disks. I attached a new jbod to one of the nodes (call it node B), which I would like to become a nsd server for this new stack of disks, but still be included in the cluster so that the disks are available to all the nodes. Node B is connected to the cluster via ethernet. How can I make the new nsd seen by all the nodes of the cluster? I can create the new nsd but when trying to create the filesystem on node B it the command mmcrfs times out. It looks like the nodes of the cluster cannot understand the filesystem location even if I specify them attached to server B in the description file. Would it be better to remove node B from the cluster, create a cluster on its own with its attached filesystem and connect it remotely with the previous cluster? Or a clustered NFS solution would apply better? Can you please give me any suggestion?

  Read the article

• JAVASCRIPT ENABLED

  - by kirchoffs415

  HI, I hope somebody can help, i keep getting the following message when i log on-- Your Javascript is disabled. Limited functionality is available. it will stay for maybe a day sometimes two.I have uninstalled javascript and reinstalled but still the same. Iam using chrome. any help would be gratefull many thanks Dominic p.s. my system spec is as follows System InformationOS Name Microsoft® Windows Vista™ Home Premium Version 6.0.6002 Service Pack 2 Build 6002 Other OS Description Not Available OS Manufacturer Microsoft Corporation System Name DOM-PC System Manufacturer Dell Inc. System Model Inspiron 1545 System Type X86-based PC Processor Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, 2000 Mhz, 2 Core(s), 2 Logical Processor(s) BIOS Version/Date Dell Inc. A05, 25/02/2009 SMBIOS Version 2.4 Windows Directory C:\Windows System Directory C:\Windows\system32 Boot Device \Device\HarddiskVolume3 Locale United Kingdom Hardware Abstraction Layer Version = "6.0.6002.18005" User Name DOM-PC\DOM Time Zone GMT Standard Time Installed Physical Memory (RAM) 3.00 GB Total Physical Memory 2.96 GB Available Physical Memory 1.38 GB Total Virtual Memory 5.89 GB Available Virtual Memory 4.25 GB Page File Space 3.00 GB Page File C:\pagefile.sys My System Specs

  Read the article

• Postfix character encoding?

  - by Anonymous12345

  I use Postfix as a mailserver. I have Ubuntu OS. Then I use PHP to send emails. Problem is that none of my emails are encoded properly by a mailsoftware which my VPS provider uses. According to them, the problem lies with me. It is only the name field which isn't encoded properly. For example "Björn" becomes "Björn" in my emails. However, when I echo the $name, it outputs "Björn" which is correct. Also, gmail and hotmail does show it correctly. The strange part is that the "text" (the message itself) is encoded properly. I use the following for sending mail: $headers="MIME-Version: 1.0"."\n"; $headers.="Content-type: text/plain; charset=UTF-8"."\n"; $headers.="From: $name <$email>"."\n"; $name= iconv(mb_detect_encoding($name), "UTF-8//IGNORE//TRANSLIT", $name); //// I HAVE TRIED WITH AND WITHOUT THE LINE ABOVE, NO DIFFERENCE mail($to, '=?UTF-8?B?'.base64_encode($subject).'?=', $text, $headers, '[email protected]'); I have tried with and without the iconv line also, no luck. The last thing I can think of is POSTFIX, could there be a setting for character encoding there? Anybody knows?

  Read the article

• Cursor lag when mouse cursor changes?

  - by Mathias Lykkegaard Lorenzen

  Cursor lag issue Introduction I'm experiencing a newly arrived problem lately that frustrates me a lot. The computer I bought is a Clevo 150ERM. Two of my friends bought the same machine, and are experiencing the same issue. The computer came with Windows 7. There, I had no issues. Then, when we all switched to Windows 8, they had the mouse problem and I didn't. That is until after 4 or 5 months when I decided to install the RTM driver of my Intel graphics chip, and the latest Nvidia driver. I also installed the latest version of Skype that just released (Skype 6 and Skype for Metro). This basically leads me to conclude that the issue is not hardware-prone, and is not based on the operating system itself, rather the drivers or components that follow with it. Description of the issue The issue itself (lag with the mouse) happens whenever the cursor icon changes. For instance, if I keep hovering from and to a textfield (and the cursor changes into a caret and then back to a mouse), it stops for 200 milliseconds while it changes the icon. An example is if I follow the mouse in the pattern shown by the arrows below. When crossing the window border, the cursor changes into a "resize window" cursor for a short while, making the cursor lag. This doesn't sound like much, but it happens every time the cursor changes (even if it's to just move the mouse somewhere else, and accidentally make it cross a window border from where the resize cursor shows etc). What do you suggest I try?

  Read the article

• where can I find the user in this IIS error 'Login failed for user 'IIS APPOOL\Web2'

  - by Jack

  I encounter the following error: Cannot open database "testbase" requested by the login. The login failed. Login failed for user 'IIS APPPOOL\Web2'. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Data.SqlClient.SqlException: Cannot open database "testbase" requested by the login. The login failed. Login failed for user 'IIS APPPOOL\Web2'. So, where can I give this user Web2 permission? (By the way, the server do not have such user Web2 but there is a folder called Web2 located at the wwwroot folder.) I search for answers but all failed as follows: [1] Add the user IUSR to the folder and give it read permission. [2] http://www.codekicks.com/2008/11/cannot-open-database-northwind.html [3] http://blog.sqlauthority.com/2009/08/20/sql-server-fix-error-cannot-open-database-requested-by-the-login-the-login-failed-login-failed-for-user-nt-authoritynetwork-service/

  Read the article

• tomcat 5.5 startup script on Ubuntu server

  - by Registered User

  Can any one share their Tomcat startup script I am looking for a tomcat start up script on a Ubuntu machine. My Ubuntu is 10.04 server. The tomcat is 5.5.30. It is in /opt/apache-tomcat-5.5.31 I tried a script #!/bin/bash # # tomcat # # chkconfig: # description: Start up the Tomcat servlet engine. # Source function library. . /lib/lsb/init-functions RETVAL=$? CATALINA_HOME="/opt/apache-tomcat-5.5.31" case "$1" in start) if [ -f $CATALINA_HOME/bin/startup.sh ]; then echo $"Starting Tomcat" /opt/apache-tomcat-5.5.31/bin/startup.sh fi ;; stop) if [ -f $CATALINA_HOME/bin/shutdown.sh ]; then echo $"Stopping Tomcat" /opt/apache-tomcat-5.5.31/bin/shutdown.sh fi ;; *) echo $"Usage: $0 {start|stop}" exit 1 ;; esac exit $RETVAL but it did not worked after a reboot. But the same script works if I do /etc/init.d/tomcat start or /etc/init.d/tomcat stop I have done update-rc.d tomcat defaults as it is a Ubuntu server but on reboot all of this fails to work.

  Read the article

• How to remove that extra text from URL titles in Firefox browser?

  - by amar

  I am using Firefox with Vimperator. On Mac I use Shiori to bookmark. I also use Pinboard's default add-on (on both Mac and Windows, but mainly on Windows as there's no Shiori). When I used to bookmark, I had this behaviour[A] (before changing Vimperator options): Example: URL: xyz.com TITLE: xyz website Pinboard add-on would fetch the title as xyz website which was fine (I reckon it directly fetches TITLE form the URL). But after installing and starting to use Shiori the title I was getting in its "title" field was xyz website - Vimperator exactly the same what I could see in tabs (seems it's getting what the browser is feeding it). So, I :set titlestring= in Vimperator to remove that extra Vimperator from title. Now, this is what I am getting [B]: When I try to bookmark using Pinboard add-on the title is undefined Using Shiori it results in xyz website - undefined. I tried to change it back to original[C] :set titlestring=Mozilla Firefox (assuming this was the original, before Vimperator) but the results are still the same as [B]. How to get read of that extra - undefined or that extra - Vimperator or - Mozilla Firefox for that matter, while bookmarking pages either with Pinboard add-on or Shiori? One workaround is, instead of no string just add a white-space while setting title in Firefox via Vimperator there but that results in - appended to titles.

  Read the article

• Apache2 on Raspbian: Multiviews is enabled but not working [closed]

  - by Christian L

  I recently moved webserver, from a ubuntuserver set up by my brother (I have sudo) to a rasbianserver set up by my self. On the other server multiviews worked out of the box, but on the raspbian it does not seem to work althoug it seems to be enabled out of the box there as well. What I am trying to do is to get it to find my.doma.in/mobile.php when I enter my.doma.in/mobile in the adress field. I am using the same available-site-file as I did before, the file looks as this: <VirtualHost *:80> ServerName my.doma.in ServerAdmin [email protected] DocumentRoot /home/christian/www/do <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /home/christian/www/do> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> From what I have read various places while googling this issue I found that the negotiation module had to be enabled so I tried to enable it. sudo a2enmod negotiation Giving me this result Module negotiation already enabled I have read through the /etc/apache2/apache2.conf and I did not find anything in particular that seemed to be helping me there, but please do ask if you think I should post it. Any ideas on how to solve this through getting Multiviews to work?

  Read the article

• Apache mod_rewrite and mod_vhost_alias Virtual Hosts and %1

  - by Matt Wall

  I have put the main bits of my httpd.conf down below. I am using %1 to get the host field so I can dynamically add vhosts by just creating dns/folders. One problem is I need to reference this: HttpStreamingLiveEventPath "D:/FMSApps/%1" HttpStreamingContentPath "D:/FMSApps/%1" In Apache when I try say to do this: http://test.domain.com/hds-vod/myfile.mp4.f4m it sees the %1 in the logs, and fails. Apache gives me this: [error] mod_jithttp [403]: No access to D:/Content/%1/DefaultContent/eve.mp4 What I'm looking for is the D:/Content/%1/DefaultContent/eve.mp4 to become D:/Content/test/DefaultContent/eve.mp4 Anyone have any useful resources / hints etc. to help me? Meanwhile my Google searching continues...! Listen 80 ServerName main1.rtmphost.com AccessFileName .htaccess ServerSignature On UseCanonicalName Off HostnameLookups Off Timeout 120 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 15 RewriteLogLevel 0 RewriteLog logs/rewrite.log DocumentRoot D:/Content LoadModule vhost_alias_module modules/mod_vhost_alias.so VirtualDocumentRoot "D:/Content/%1" RewriteEngine On <Directory /> Options None AllowOverride None Order allow,deny Allow from all Satisfy all </Directory> <IfModule f4fhttp_module> <Location /vod> HttpStreamingEnabled true HttpStreamingContentPath "D:/FMSApps/%1" Options FollowSymLinks </Location> Redirect 301 /live/events/livepkgr/events /hds-live/livepkgr <Location /hds-live> HttpStreamingEnabled true HttpStreamingLiveEventPath "D:/FMSApps/%1" HttpStreamingContentPath "D:/FMSApps/%1" HttpStreamingF4MMaxAge 2 HttpStreamingBootstrapMaxAge 2 HttpStreamingFragMaxAge -1 Options FollowSymLinks </Location> </IfModule>

  Read the article

• Makecert.exe hangs

  - by Robert

  I was following the steps in Scott Hanselman's blog post describing how to create a certificate authority and code signing certificate for PowerShell scripts. Initially, I created the certificate authority and a personal certifcate and used it to sign a powershell script successfully. All went as described in the blog post. The problem starts (as most do) when I did something that was (probably) stupid, although it seemed reasonable at the time. I wanted to start over and repeat the process again with a clean slate, so from the mmc certificates snap-in console, I deleted the personal certificate and the certificate authority I created previously. After that any time I try to use makecert, (just as I did the first time around), makecert either hangs or faults (which prompts to end or debug). Did I hose something up by deleting via the certificates snap-in? It didn't complain or warn me that it could be potentially hazardous. Is this just coincidence and something else entirely could be hosed? I have Event Log entries from the times when makecert crashed, which all look very similar; here is one: Log Name: Application Source: Application Error Date: 8/5/2009 3:55:04 PM Event ID: 1000 Task Category: (100) Level: Error Description: Faulting application makecert.exe, version 6.0.6000.16384, time stamp 0x4545910b, faulting module ntdll.dll, version 6.0.6002.18005, time stamp 0x49e03821, exception code 0xc0000005, fault offset 0x00067409, process id 0xe58, application start time 0x01ca160efdf30625. Anyone have any ideas as to what exactly caused this and/or what I can do to fix it. I'm on 32-bit Vista Enterprise w/SP2.

  Read the article

• AMIs in Amazon EC2

  - by Jack of Trades

  I really like the Amazon EC2 environment, and thought I'll spend a bit of time playing around with various types of public (Windows!) AMI servers. But testing has been a bit, well, questionable. Some of my findings: It's very difficult to know what exactly a specific public EC2 image is supposed to be doing. Many images come with little to no information. I can't seem to find the passwords to log onto various windows images. Why are they public if they can't be used!? Lots of images are based on S3, and not EBS backed. This is very annoying, as S3 takes a lot longer to do pretty much anything (stop, image etc.) I am only testing images here, so of-course I don't question the value of S3 for other attributes. The description of what an image does is almost useless and many times confusing. Have others come across these EC2 issues. Again, my interest was to just play around with public images for testing/experimentation/etc, and therefore these issues may not be too relevant for more normal EC2 deployment uses.

  Read the article

• Generic RPM package for Python 2.x

  - by RaphDG

  I have a python application, it can run on Python = 2.6 and it's architecture independant. I need the rpm package of this application to be installed on Fedora 14 (python 2.7) and Centos 6.2 (python 2.6). I currently use mock to build one rpm package for each "flavour" and it works well. I apparently can't install the Centos compiled rpm on Fedora. It gives me this error message : error: Failed dependencies: python(abi) = 2.6 is needed by myapp-0.9.el6.noarch Here is the relevant part of my .spec file : %{!?python_sitelib: %global python_sitelib %(%{__python} -c "from distutils.sysconfig import get_python_lib; print(get_python_lib())")} %{!?python_sitearch: %global python_sitearch %(%{__python} -c "from distutils.sysconfig import get_python_lib; print(get_python_lib(1))")} Name: myapp Version: #VERSION# Release: #RELEASE#%{dist} Summary: myapp Group: Development/Languages License: Apache v2 Source0: %{name}-%{version}-#RELEASE#.tar.gz BuildRoot: %{_tmppath}/%{name}-%{version}-%{release}-root-%(%{__id_u} -n) BuildArch: noarch BuildRequires: python-devel BuildRequires: python-setuptools %description myapp %prep %setup -c %build %{__python} setup.py build %install %{__rm} -rf %{buildroot} %{__python} setup.py install -O1 --skip-build --root %{buildroot} Do I really have to use mock and build 2 rpms or is there another way to create a single generic 2.x rpm package ?

  Read the article

• Rename a Network Printer win Win 7

  - by Alex

  Seems this is a common question but the answers regularly miss the point. I have a server. Server has some printers connected. Server has all drivers for x32 & x64 OS PLUS ALL DEFAULTS set. Server also manages print queue. I have many workstations, all need to use the printers. All NEED to have drivers print queue and DEFAULTS propagated from server. Now.... When I add the printers on the workstations, I get: "ABC Printer on SERVER123" I need something less long - just "ABC Printer" So how? Tip: Please don't show me how to change the name of your locally installed printer. I know how to do this - I am particularly interested in shared printers that look like "ABC Printer on SERVER123" Tip: Installing the driver with a local port wont cut it because then I loose the server propagated defaults, the driver updates and I need to run around with driver disks/confuse trembling users with hard things like choosing drivers. I am happy for a hack if there is no official way to do this in the group policy.... I tried looking in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Printers on the workstation machines but those are only local printers :( I can see the network printer details on the workstations here: HKEY_USERS[Some GUID]\Printers\Connections But there is nothing obvious like a description string... Can anyone help with this?

  Read the article

• I love google Chrome, but some non-static pages like Piwik render it unresponsive

  - by gogowitsch

  The web-stat software Piwik stops reacting on mouse clicks after 1-2 seconds. The same is true for Google Maps and Producteev (but GMail and most other pages work like a charm). These rely heavily on JS, and work without Flash. I can click for a very short time period and then the mouse cursor doesn't feel the UI anymore (it doesn't turn into a I over input fields, though it moves; if the freeze occured while the pointer was over an input field, the cursor keeps being a I) and all clicks on the DOM are being ignored by Chrome. No message appears, neither obvious nor in the Console (F12). There is no obstructing div or the like in the DOM (F12). Since I couldn't find any hints on the source of my problems, I suspected my plugins and extensions. Unfortunately, neither deactivating all plugins nor all extensions solved the problem. for the problematic pages, it always happens no Dropbox running several GB of free RAM the taskmanager doesn't show any high CPU or memory utilization (the offending tab uses 30 MB and uses 0-1 % CPU) all problematic pages work in other browsers (Chrome, Firefox, IE) the rest of the computer is very responsive the computers use different security suites (Kaspersky and Avira) The effect exists between several (synchronized) Chrome instances on different machines, all running Windows 7. Both the OS and Chrome are updated automatically. Other tabs and the Chrome chrome (tabs, menus, toolbar buttons of the browser itself) still work. I really don't like switching between browsers. Any ideas?

  Read the article

• Changing MX records in named zone file

  - by Paul England

  I forgot how all this works. I have a GoDaddy account, using my own DNS and whatnot. I'm having trouble getting my email to work. They said I need to update my MX records. basically, I have the following. 184.168.30.42 is the domain's IP address, obviously. gamengai.com. 14400 IN NS n1 gamengai.com. 14400 IN NS n2 ns1 14400 IN A 184.168.30.42 ns2 14400 IN A 184.168.30.42 gamengai.com. 14400 IN A 184.168.30.42 localhost 14400 IN A 127.0.0.1 ftp 14400 IN A 184.168.30.42 www 14400 IN A 184.168.30.42 mail 14400 IN A 184.168.30.42 subdomain 14400 IN A 184.168.30.42 gamengai.com 14400 IN MX 10 mail Mail doesn't work though... they say to make the following change: 0 smtp.secureserver.net 10 mailstore1.secureserver.net So should the last line point to mailstore1.secureserver.net instead of mail in the last field? What about the other line? I had this working at one time, but it's totally gotten away from me. It's a virtual dedicated server and their support for this stuff is pretty bad... almost as bad as my admin skills since I went the programmer route.

  Read the article

• Gentoo Linux useful utilities

  - by Alakdae

  I want to make a list of utilities that come in handy in Gentoo (general Linux tools available in all distributions also appreciated). What tools and commands do you use and consider helpful in administration of a Gentoo server? I will update the list with command from answers from time to time. eclean Utility for cleaning distfiles and binary packages. Usage example: eclean distfiles Usage example output: Cleans out the files in /usr/portage/distfiles. Pretty handy. Package: app-portage/gentoolkit eix Very useful tool for getting information about a package. Similar to "emerge -s" but much faster and more precise. Usage example: eix gentoolkit Usage example output: Show information about package such as: available versions, masked versions, installed versions and description. Package: app-portage/eix eix-test-obsolete Check system for obsolete, redundant, uninstalled entries in package.keywords, package.mask, package.unmask, package.use and package.cflags Usage example: eix-test-obsolete Usage example output: Shows non-matching entries, redundant entries, and uninstalled entries. Package: app-portage/eix equery Another very useful tool for getting information about packages (listing package files, checking which files belong to which package and much more) Usage example: equery b emerge Usage example output: Show which packages installed a file called emerge Package: app-portage/gentoolkit genlop Utility for extracting information about emerged ebuilds Usage example: genlop -l --date yesterday Usage example output: Show a list of packages that have been emerged yesterdayPackage: app-portage/genlop glsa-check Checks system if it's affected by GLSAs (security issues) Usage example: glsa-check -l affected Usage example output: List of GLSA that the system is affected by. Package: app-portage/gentoolkit rc-update Utility for managing (adding, deleting) runlevel scripts. Usage example: rc-update add syslog-ng default Usage example output: Adds syslog-ng to default runlevel. Package: sys-apps/baselayout revdep-rebuild Scans libraries and binaries for missing shared library dependencies Usage example: revdep-rebuild Usage example output: Gather binaries and libraries information, check for dependencies, rebuild packages with missing dependencies Package: app-portage/gentoolkit

  Read the article

• How to test email spam scores with amavis?

  - by CaptSaltyJack

  I'd like a way to test a spam message to see its spam scores that SpamAssassin gives it. The SA db files (bayes_toks, etc) reside in /var/lib/amavis/.spamassassin. I've been testing emails by doing this: sudo su amavis -c 'spamassassin -t msgfile' Though this yields some strange results, such as: Content analysis details: (3.7 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- 3.5 BAYES_99 BODY: Bayes spam probability is 99 to 100% [score: 1.0000] -0.0 NO_RELAYS Informational: message was not relayed via SMTP 0.0 LONG_TERM_PRICE BODY: LONG_TERM_PRICE 0.2 BAYES_999 BODY: Bayes spam probability is 99.9 to 100% [score: 1.0000] -0.0 NO_RECEIVED Informational: message has no Received headers 0.2 is an awfully low scores for BAYES_999! But this is the first time I've used amavis, previously I've always just used spamassassin directly as a content filter in postfix, but apparently running amavis/spamassassin is more efficient. So, with amavis in the picture, how can I run a test on a message to see its spam score breakdown? Another email I ran a test on got this result: 2.0 BAYES_80 BODY: Bayes spam probability is 80 to 95% [score: 0.8487] Doesn't make sense, that BAYES_80 can yield a higher score than BAYES_999. Help!

  Read the article

• Hyperic HQ- Monitor process statistics for 50+ processes on Linux machine

  - by Chris

  Is there an easy way to get metrics on all processes that start with the letters XYZ? I have about 80 processes that I have to monitor individually that all start with the prefix XYZ. I have created a query using the sigar shell: ps State.Name.sw=XYZ, which will give me a list of the processes that I want. What I need to do is define this list of processes through said query and collect and track statistics from the Process service: http://support.hyperic.com/display/hypcomm/Process+service What I need is 3 or 4 key statistics for each of the XYZ processes defined by my query to show up as graphs in the web front end. Note: Hyperic HQ server is installed on a windows machine and I'm monitoring a Linux box via an agent. Thanks, Chris Edit: Here is my try at a plugin that may give me what I want, but it's not being inventoried/detected by the Hyperic web UI. Simply pointing me to one of Hyperic's tutorials won't do. Thanks. <!DOCTYPE plugin [ <!ENTITY process-metrics SYSTEM "/pdk/plugins/process-metrics.xml">]> <plugin> <server name="ABCStats"> <config> <option name="process.query" description="Process Query" default="State.Name.sw=XYZ"/> </config> <metric name="Availability" alias="Availability" template="sigar:Type=ProcState,Arg=%process.query%:State" category="AVAILABILITY" indicator="true" units="percentage" collectionType="dynamic"/> &process-metrics; <plugin type="autoinventory"/> <plugin type="measurement" class="org.hyperic.hq.product.MeasurementPlugin"/> </server> </plugin>

  Read the article

• How do i tell if my drivers are up to date on Acer?

  - by joe

  Hoping some kind souls can help me out ? I got a blue screen the other day after trying to load sandboxie. So its obviously conflicting with something. I checked if my drivers were up to date on my acer aspire one AOD270 on this intel based site; http://www.drivermanager.com/en/down...tel&Logo=intel Its showing i have 2 drivers that need updating ; Intel NM10 Express chipset and the Realtek PCIE Cardreader. I have no idea whether to do the update via the Intel Driver update site or the Acer drivers download page? I then ran Bluescreenview and on the dump file its showing ; ''caused by driver'' igdkmd32.sys ''file description'' Intel (R) WDDM Kernel mode driver ''product name''Intel Graphics Accelerator Drivers for Windows 7(R) I bought the laptop here in SE Asia about a year ago. The ''HOT!! NEW download tool'' on the acer drivers site (below) doesnt seem to work and the info about removing and installing drivers is limited. Not sure what to trust on non acer/manufacturer sites. http://support.acer.com/us/en/produc...1&modelId=4040 I've located the igdkmd32.sys file inside the INTEL GRAPHICS MEDIA ACCELERATOR 3600 SERIES 8.14.8.1064. When i click on ''update driver'' in control panel it searches and says its up to date. In windows maintenance it says this intel had a problem, but no solution. For all i know my drivers could be up to date and its something else. Can anybody advise a dummy step by step the process i should follow ? I've never done this before. eg do i delete the old driver first and then download the new one.how much of a problem i could cause by downloading this type of thing wrongly? As yet i havent downloaded any drivers. I've asked on other forums but no luck as yet. Thanks for any help!

  Read the article

< Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >