Search Results

Search found 16598 results on 664 pages for 'device center'.

Page 536/664 | < Previous Page | 532 533 534 535 536 537 538 539 540 541 542 543  | Next Page >

• Debian software raid 1: boot from both disk

  - by bsreekanth

  I newly installed debian squeeze with software raid.The way I did was, as also given in this thread. I have 2 HDD with 500 GB each. For each of them, I created 3 partitions (/boot, / and swap) I selected the hard drive and created a new partition table I created a new partition that was 1GB. I then specified to use the partition as a Physical Volume for RAID. and used for /boot and enabled bootable. Created another partition, which is of 480 GB, and then specified to use the partition as a Physical Volume for RAID. and used for /. Created another partion and used for swap Then RAID configuration: Through Configure RAID menu - create MD device - (2 for the number of drives, 0 for spare devices) Next select the partitions you want to be members of /dev/MD0. I selected /dev/sda1 and /dev/sdb1 (for /boot) Next select the partitions you want to be members of /dev/MD1. I selected /dev/sda6 and /dev/sdb6 (for /) And no RAID for swap partitions 'Finish Partitioning and write changes to disk' -- Finish the rest of the install like normal Everything is ok now, except I am not sure how to test my raid config. When I pull the power of the HDD, it only boots from one disk. I read in some forum that I may have to install GRUB manually on the other. In Debian Squeeze, there is no grub command. Not sure how to make my software raid bootable from both disk. Also, please comment on my steps above. Anything unusual. I configured /boot partitions of both disks to be boot=yes. Not sure whether that is ok. Thanks, Bsr

  Read the article

• Juniper NetScreen NS-5GT traffic monitoring

  - by blah

  I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

  Read the article

• ephemeral vs EBS partitions

  - by hortitude

  I launched an EBS backed AMI with all the defaults. I noticed that it automicatlly had attached an ephemeral disk. I was just wondering if there was a good programtic way to know that this particular device is ephemeral vs some EBS volume I had decided to attach: ubuntu@-----:~$ df -ahT Filesystem Type Size Used Avail Use% Mounted on /dev/xvda1 ext4 7.9G 867M 6.7G 12% / proc proc 0 0 0 - /proc sysfs sysfs 0 0 0 - /sys none fusectl 0 0 0 - /sys/fs/fuse/connections none debugfs 0 0 0 - /sys/kernel/debug none securityfs 0 0 0 - /sys/kernel/security udev devtmpfs 1.9G 12K 1.9G 1% /dev devpts devpts 0 0 0 - /dev/pts tmpfs tmpfs 751M 172K 750M 1% /run none tmpfs 5.0M 0 5.0M 0% /run/lock none tmpfs 1.9G 0 1.9G 0% /run/shm /dev/xvdb ext3 394G 199M 374G 1% /mnt ubuntu@-----:~$ mount /dev/xvda1 on / type ext4 (rw) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/xvdb on /mnt type ext3 (rw,_netdev)

  Read the article

• how to correctly mount fat32 partition in Ubuntu in order to preserve case

  - by Dean

  I've found there are couple of problems might be related how my FAT32 partition was mounted. I hope you can help me to solve the problem. I also included the command I used to help others when they find this post, sorry to those might feel I should use less space. I've the following file structures on my disk dean@notebook:~$ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x08860886 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 5737 45978624 7 HPFS/NTFS /dev/sda3 5738 10600 39062047+ 83 Linux /dev/sda4 10601 19457 71143852+ 5 Extended /dev/sda5 10601 11208 4883728+ 82 Linux swap / Solaris /dev/sda6 11209 15033 30720000 b W95 FAT32 /dev/sda7 15033 19457 35537920 7 HPFS/NTFS In the etc/fstab I've got UUID=91c57a65-dc53-476b-b219-28dac3682d31 / ext4 defaults 0 1 UUID=BEA2A8AFA2A86D99 /media/NTFS ntfs-3g quiet,defaults,locale=en_US.utf8,umask=0 0 0 UUID=0C0C-9BB3 /media/FAT32 vfat user,auto,utf8,fmask=0111,dmask=0000,uid=1000 0 0 /dev/sda5 swap swap sw 0 0 /dev/sda1 /media/sda1 ntfs nls=iso8859-1,ro,noauto,umask=000 0 0 /dev/sda2 /media/sda2 ntfs nls=iso8859-1,ro,noauto,umask=000 0 0 I checked my id using id and I've got dean@notebook:~$ id uid=1000(dean) gid=1000(dean) groups=4(adm),20(dialout),24(cdrom),46(plugdev),103(fuse),104(lpadmin),115(admin),120(sambashare),1000(dean) I don't know why with these settings I still have problem of using svn like in this one Thank you for your help!

  Read the article

• How to set up a serial connection to a Windows 7 computer

  - by oli_arborum

  I need to set up a "dial in" connection to a Windows 7 (Ultimate) computer via a serial null-modem cable to be able to connect from a Windows XP client to that computer and exchange data over IP. Question 1: How do I do that? I did neither find the information via Google nor in the MSDN. Seems like no one tried ever before... ;-) I already managed to install a legacy modem device called "Communications cable between two computers" and found the menu entry "New Incoming Connection..." in Network and Internet Network Connections. When I finish this wizard I get the message that the "Routing and Remote Access service" cannot be started. In the event viewer I see the following error messages: "The currently configured authentication provider failed to load and initialize successfully. The requested name is valid, but no data of the requested type was found." (Source: RemoteAccess, EventID: 20152) "The Routing and Remote Access service terminated with service-specific error The requested name is valid, but no data of the requested type was found." (Source: Service Control Manager, EventID: 7024) The Windows 7 installation is "naked", i.e. no additional software or services are installed. Question 2: Am I on the right path to set up the connection? Question 3: How can I get the Routing and Remote Access service running?

  Read the article

• Windows 7 boot failure after update

  - by Jake

  Installed some windows 7 updates today, mostly just optional fixes and it installed an update to my IntelliType or IntelliPoint drivers (Keyboard & Mouse). It asked to reboot, computer gets to the windows load screen and redirects to the repair utility. Repair utility failed, it said if I recently installed a device, unplug it and try to restart. So I unplugged my keyboard and mouse, restarted. Nothing. I noticed that all the errors seemed to be Windows 7 thinking the installation was on another one of my slave drives. For example, my windows installation is on C:, but I have other drives, like G:, X:, etc... So it said "Critical Boot File G:\Windows\system32\drivers\amdxata.sys is corrupt, but why not C:\ ? So I unplugged ALL other hard drives, it still tried loading X:, even though the only one plugged in was C: I have the windows disk, but that didn't seem to help. I was thinking I need to fix my boot.ini or something simple like that was corrupt, the hard drives seem fine. I'm screwed, it's finals week.

  Read the article

• Why does USB thumb drive screw up boot sequence?

  - by Carl B

  I am looking for understanding to a boot issue. I have at times had some files and such that I save and retrieve from my thumb drive. I use the front panel as it is nice and easy to get to and I typically power down my system nightly. If I forget to pull the drive and power on the system, it becomes the first bootable device. As there is no OS on the USB Drive I get the BOOTMGR is missing press CTRL+ALT+DELETE. When I go into BIOS to see Boot sequence, there’s the thumb drive up top, DVD drive is missing and not found in the list of devices. All of the hard drives are next in line. When I pull the USB drive, and reboot, everything is back to normal. Old boot sequence is in place, DVD drive right where it should be and no issues. So why does this happen with a USB drive in port at boot up? If it can’t be booted from, shouldn’t the next drive be attempted? Note: This happens when the thumb drive is plugged into a USB port on the front panel. It does not seem to happen on rear panel ports.

  Read the article

• best-practices to block social sites

  - by adopilot

  In our company we have around 100 workstation with internet access, And day by day situation getting more worst and worst from perspective of using internet access for the purpose of doing private jobs, and wasting time on social sites. Open hearted I am not for blocking sites like Facebook, Youtube, and others similar but day by day my colleagues do not finishing his tasks and while I looking at their monitor all time they are ruining IE or Mozilla and chat and things like that. In other way Ill like to block youtube sometime when We have very poor internet access speed, Here is my questions: Do other companies blocking social sites ? Do I need dedicated device for that like hardware firewall, super expensive router Or I can do that whit my existing FreeBSD 6.1 self made router with two lan cards and configured nat to act like router. I was trying do that using ipfw and routerfirewall but without success, My code looks like ipfw add 25 deny tcp from 192.168.0.0/20 to www.facebook.com ipfw add 25 deny udp from 192.168.0.0/20 to www.facebook. ipfw add 25 deny tcp from 192.168.0.0/20 to www.dernek. ipfw add 25 deny udp from 192.168.0.0/20 to www.dernek. ipfw add 25 deny tcp from 192.168.0.0/20 to www.youtube. ipfw add 25 deny udp from 192.168.0.0/20 to www.youtube.com

  Read the article

• some windows 8 metro (modern UI) apps don't open, but live tiles DO work

  - by DiegoDD

  Some of my default windows 8 metro (modern UI) apps don't work properly, the apps are the Weather and the News apps. when I open them, I only get the loading screen, that is, the big colorful screen with the logo in the center, and the "loading" spinning dots. They just keep like that forever and never actually open. There are no error messages or anything. The strange this is that the live tiles for those apps DO work and show current information. current weather for my location (saved before they started failing) and current news. Both apps did work well in the past, and every other default windows 8 app I've tried work well (both live tiles and the app itself). Every other non-default apps that I've downloaded still work correctly, so the problem so far is only with those two apps. (weather and news). I really don't know since when exactly they started to fail because I really don't use them (or any metro app) that often, so I can't recall if I did something like installing some other app, either metro or regular, or messed with some drivers, etc. they simply don't open now, but they DID work before. any ideas?

  Read the article

• How do I get a Wireless N PCi card to connect to a wireless G router?

  - by Andy

  I'm having some problems setting up a new wireless PCI card on a WinXP SP3 PC. I know that the router is configured correctly. It is a Linksys WRT54GL, using 802.11b/g. Security mode is WPA2 Personal with TKIP+AES encryption. I am able to connect to this fine using my laptop (first gen MacBook with a 802.11b built in card). The new PCI card is also Linksys, but it supports 802.11n. Card seems to be installed ok (Windows sees it fine, doesn't list any errors in Device Manager), however when it scans for available wireless networks it can't find my wireless network (the router is set to broadcast the SSID). I tried to enter the network SSID manually, but that didn't seem to help. I chose WPA2-PSK for network authentication. The only options for encryption are TKIP or AES - I've tried both, neither worked. I am sure that I typed in my wireless key correctly. At this point, I don't think the problem is with encryption, but something else. It almost seems like I need to switch the wireless card into g mode, but I haven't found a way to do that (if that is even possible/necessary - I thought n was fully backwards compatible with g). Also, the PC is in the same room as the router, and my laptop, so I don't think that it is an interference issue. Any ideas what I'm doing wrong? I'm running out of things to try at this point. :(

  Read the article

• VMware Data Recovery error -3960 and Event ID 8193 on Windows Server 2003

  - by flooooo

  I've been trying to solve this problem since a few days now without any success. What I'm trying is to make a backup of a virtual machine running Windows Server 2003 SP 2 using VMware Data Recovery 2.0.0.1861. When starting the backup task it tries to make a snapshot of the virtual machine using VSS which fails with error: Event Type: Error Event Source: VSS Event Category: None Event ID: 8193 Date: 05.06.2012 Time: 12:12:01 User: N/A Computer: LEGOLAS Description: Volume Shadow Copy Service error: Unexpected error calling routine RegSaveKeyExW. hr = 0x800703f8. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 2d 20 43 6f 64 65 3a 20 - Code: 0008: 57 52 54 52 45 47 52 43 WRTREGRC 0010: 30 30 30 30 30 33 39 36 00000396 0018: 2d 20 43 61 6c 6c 3a 20 - Call: 0020: 57 52 54 52 45 47 52 43 WRTREGRC 0028: 30 30 30 30 30 33 31 38 00000318 0030: 2d 20 50 49 44 3a 20 20 - PID: 0038: 30 30 30 30 36 34 38 38 00006488 0040: 2d 20 54 49 44 3a 20 20 - TID: 0048: 30 30 30 30 34 33 38 34 00004384 0050: 2d 20 43 4d 44 3a 20 20 - CMD: 0058: 43 3a 5c 57 49 4e 44 4f C:\WINDO 0060: 57 53 5c 53 79 73 74 65 WS\Syste 0068: 6d 33 32 5c 76 73 73 76 m32\vssv 0070: 63 2e 65 78 65 20 20 20 c.exe 0078: 2d 20 55 73 65 72 3a 20 - User: 0080: 4e 54 20 41 55 54 48 4f NT AUTHO 0088: 52 49 54 59 5c 53 59 53 RITY\SYS 0090: 54 45 4d 20 20 20 20 20 TEM 0098: 2d 20 53 69 64 3a 20 20 - Sid: 00a0: 53 2d 31 2d 35 2d 31 38 S-1-5-18 This machine was converted p2v. I have no idea where to search for the problem and what to do. Google showed a few result but none of them were useful for me. Please help me. If you need further information I'll tell you - just ask!

  Read the article

• Openldap with ppolicy

  - by nitins

  We have working installation of OpenLDAP version 2.4 which is using shadowAccount attributes. I want to enable ppolicy overlays. I have gone through the steps provided at OpenLDAP and ppolicy howto. I have made the changes to slapd.conf and imported the password policy. On restart OpenLDAP is working fine and I can see the password policy when I do a ldapsearch. The user object looks like given below. # extended LDIF # # LDAPv3 # base <dc=xxxxx,dc=in> with scope subtree # filter: uid=testuser # requesting: ALL # # testuser, People, xxxxxx.in dn: uid=testuser,ou=People,dc=xxxxx,dc=in uid: testuser cn: testuser objectClass: account objectClass: posixAccount objectClass: top objectClass: shadowAccount shadowMax: 90 shadowWarning: 7 loginShell: /bin/bash uidNumber: 569 gidNumber: 1005 homeDirectory: /data/testuser userPassword:: xxxxxxxxxxxxx shadowLastChange: 15079 The password policy is given below. # default, policies, xxxxxx.in dn: cn=default,ou=policies,dc=xxxxxx,dc=in objectClass: top objectClass: device objectClass: pwdPolicy cn: default pwdAttribute: userPassword pwdMaxAge: 7776002 pwdExpireWarning: 432000 pwdInHistory: 0 pwdCheckQuality: 1 pwdMinLength: 8 pwdMaxFailure: 5 pwdLockout: TRUE pwdLockoutDuration: 900 pwdGraceAuthNLimit: 0 pwdFailureCountInterval: 0 pwdMustChange: TRUE pwdAllowUserChange: TRUE pwdSafeModify: FALSE I do not what should be done after this. How can the shadowAccount attributes be replaced with the password policy.

  Read the article

• copying an lvm partition to a smaller disk, and renaming volume groups.

  - by dlamblin

  I was trying to shrink a vmdk (VMWare disk image) file to be as small as possible, and found two recommendations. The first is to cat /dev/zero into the fs then delete it, and run VMWare tools' shrink. This works okay. The second is to copy everything into a new vmdk. I went the second route. I did not use dd because I actaully want to use as few blocks as possible, instead of having a block-by-clok copy. Any unlinked files will still have blocks that aren't zeroed out. Secondly the centos image was mostly lvm, except for the boot partition, and my target was going to be 4gb instead of 8gb. I did use dd for the first 40mb to get the boot blocks and partition copied. I then used parted to create an identical primary boot, and smaller primary lvm. Then I used pvcreate on that device sdb2, vgcreate, and lvcreate to create a root and swap. I used mkfs.ext3fs on the root partition and then rsync -av / /2root excluding /proc /sys /2root /dev. So far everything went fine. My problem is that: The result is 2.7 GB while the source was 2.1 GB. This is weird to me. The second vgroup is called VolGroup01, while the original was called VolGroup00. How can I rename the VolGroup01 to VolGroup00 and swap it out after all this?

  Read the article

• [URGENT HELP PLEASE]USB Flash Drive Problem!

  - by Daren

  Here it goes. My friend saved by his works into my flash drive which was detectable/openable but ... The very next day, the drive wouldn't show up in My Computer and Windows gave him error code 43 (Unknown device). I been searching for the next few hours to find a solution as the works inside is important to him. I know he should back up his files but let's not go there. So .... I tried others few systems that once detected his flash drive but the problem still persisted. I don't know whether or not his flash drive is damaged but when plug/un-plugging, there are still sounds coming out though. Tried solutions: [On Vista Home Premium/HIS COME]Uninstalled -- Restarted com -- Re-installed (ERROR 43) [Windows 7/MY COM] Uninstalled --- Restarted com --- Can't install (ERROR 43) It seems that my com (Windows 7) had the lastest drivers already but still can't detect it. Its a Kingston DataTraveller 101 (DT101) 8GB. Could unplugging the flash drive without clicking "Safely Remove Hardware" is the problem? Kindly provide some help. Thank you all.

  Read the article

• ATI HDMI Audio disappears in Windows 7 when a TV is connected

  - by jsalonen

  So far I have unsuccessfully googled for HOURS with no luck fixing this very annoying problem. The settings is the following: I have PC running Windows 7 RC (64-bit) Video card is a ATI Radeon 4850 series card (Sapphire HD 4850 512MB to be exact) The video card has HDMI out with built-in audio chip I have an HDMI cable connecting the PC to a TV (Sony Bravia series) The problem is that when I connect the HDMI cable to the TV, the ATI HDMI Sound output device disappears completely from the list of playback devices in Windows. As a workaround I can restore the audio by re-installing the HDMI audio driver. However, when I disconnect the TV the driver disappears again. So basically, every time I want to watch stuff on my TV, I have to reinstall audio driver, which of course is VERY annoying. EDIT: I have figured out that I do not need to re-istall the HDMI audio driver to restore sound; I only need to reboot my computer with the HDMI cable plugged in to restore the audio driver. This suggests that the problem has something to do with information passed from TV to computer, which makes my HDMI Audio driver disappear. Are there any other, more elegant workarounds for this problem? All help is much appreciated!

  Read the article

• How can I parse/ transform text log data before it gets captured in SCOM 2007 R2?

  - by Abs

  I'm pretty much a noob with System Center Operations Manager 2007, and I'm probably missing something pretty basic, but I'm stumped anyway. We're setting up monitoring on some of our servers, and we'd like to capture data from some plain text log files (e.g. DNS debug logs, DHCP logs). It looks to me like I can set up a generic text file monitoring rule and get events captured into the main Ops Manager database, but my understanding is that the whole line of text from the plain text log gets captured as one field. In an ideal world, we'd be able to parse or transform that log file data to make it easier to query later. Is this possible? Is it easy? Do I have to buy expensive 3rd-party software to do it? One more thing: it would be even better if there was a way to stuff this data into the Audit Collection Services (ACS) database instead of the main one, but I'll take what I can get. Any help would be greatly appreciated.

  Read the article

• Hard drive not correctly recognized on a new Windows 7 installation, but works correctly on Windows XP

  - by david

  I'm having problems configuring a hard disk in a brand new, clean Windows 7 installation. System specs: Hard disk: WD VelociRaptor WD6000HLHX (600 GB, 10000 RPM) Motherboard: Gigabyte Z77X-UD3H BIOS SATA mode set to AHCI (not RAID), with disk connected to SATA0 (6 Gb/s port). Windows 7 Enterprise SP1 64-bit The disk is recognized by the BIOS and is correctly identified, with the name and size correctly reported. Windows recognizes the disk itself and reports the device is functioning correctly, but it doesn't appear in Explorer. Disk Management shows the drive, but incorrectly states that it is uninitialized and has no partitions. If I try to initialize the drive, I get an error saying that "the system cannot find the file specified" (what file?). Before connecting the drive to the new machine, I partitioned and formatted it under Windows XP SP2, creating 2 partitions (MBR, not GPT) and copying over a boatload of data. However, none of this data appears under Windows 7. If I put the disk back into the Windows XP machine, I can access the disk and all of its data. Is it possible to get Windows 7 to correctly recognize the disk without having to erase it and start over? If so, how do I do so? I checked this question, which seems to cover the same issue, but it didn't help.

  Read the article

• Possible to IPSec VPN Tunnel Public IP Addresses?

  - by caleban

  A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

  Read the article

• High latency issue for web service call from amazon aws ec2 to local server

  - by SibzTer

  We have a legacy web application that is running in our data center on premises located in Houston. We have a developed a new .net 4 based web application in order to provide new features to customers. The new web application is hosted in amazon aws ec2 environment (N. Virginia region us-east-1b zone). In order to get seamlessly integrate with the legacy application the new web application makes web service calls to retrieve data. We are seeing an unusually high latency time in the order of 5+ seconds for these web service calls. The exact same web service call returns in less than a second on our local PCs (which makes sense given physical proximity to the actual server). The weird part is that we have developers in California who also have the same milliseconds response time. We are testing the web service response using third party tools such as SoapUI, Google Chrome extensions such as Advanced REST Client, Postman REST Client, etc. As if this wasnt weird enough, we have noticed the same low latency from certain other ec2 instances while testing which are in the same region and availability zone as well. If we experienced the high latency consistently from all the ec2 instances I could understand. But there is something else going on. Comparing the various stats and results between the low latency and high latency ec2 servers do not show any significant differences: ping (constant 40ms), tracert, winmtr, etc. We have instances that are in the VPC as well. So I tried both the public and private IP address of the web service host server and that didnt make a difference either for the above results. We need to resolve this latency issue as this is causing the resulting web pages to load very slowly (almost 15+ seconds which is simply unacceptable). The ec2 instances have Windows Server Datacenter 64 bit. Let me know if there is any other infor I can provide to help diagnose this.

  Read the article

• RAID Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. For their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• Two audio streams - headphones and speakers

  - by Sylvester

  What I want (this is probably hard for most to answer, as this is a very unique setup) is to have two different streams (this means audio splitter is not an option, as it will still only be one stream) of audio - one through the headphones and one through the main speakers. I can do the audio rerouting using virtual audio cables, however the problem is this: i cannot get both headphones AND speakers to play even just one stream, let alone two seperate ones. using "split front and back audio into seperate streams is not an option, as the actual MB F_PANEL is faulty (nothing to do with the case front panel, just so you know. that works fine) So, first things first. I need it to recognise the headphones as a seperate audio device so that Virtual Audio Cables will detect it and allow me to route the necessary audio to the headphones only. I also need to be able have sound play through speakers and headphones together what i want to achieve overall, is this: have the ENTIRE computer's sounds picked up by VAC, and stream them to Line1. then have Line1 stream to the headphones. that way whatever's being streamed is heard through the headphones, while the entire system sounds (including those not streamed) are played through speakers.

  Read the article

• Resolving a BSOD/CPU/GPU issue...

  - by Christian Sciberras

  Hello all, I'm getting a BSOD / system crash (sometimes the PC just quits without a BSOD). Hardware Specifications cpu: i7 920 2666MHz / 8 cores (not OCed afaik) mobo: Asus P6T SE ram: 2x Corsair CM3X2G1333C9 (64bit DDR3 667MHz) gfx: ATI Radeon HD 5970 1GB (XFX HD5970 BE) os: Windows 7 Ultimate 64 bit (legit) All bios, firmware and drivers are all up to date (as of today). Symptoms Sometimes the PC runs smoothly, sometimes I get this BSOD. The BSOD always happens when I'm doing something related to graphics, such as viewing a video or playing a game. I get to know about the imminent BSOD ~10 seconds earlier; the PC starts freezing occasionally but increasing in frequency and length of lag (I noticed processor usage in creased from Process Monitor). I've tweaked BIOS settings occasionally but afaik, it was in vain. A day or so ago, I reset it to factory settings. BSOD contents The computer has rebooted from a bugcheck. The bugcheck was: 0x00000101 (0x0000000000000019, 0x0000000000000000, 0xfffff88001f35180, 0x0000000000000004). 15-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 4 23-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 2 Important The interesting thing is that although the event log (and BSOD screen) blame a "secondary processor", Windows Action Center sometimes blamed the GFX driver (for the same error). Also It is interesting to note that after hibernating my PC, I always get the BSOD.

  Read the article

• Centos 6.2 Fresh 'Basic Server' install networking issues

  - by RWC

  I've had a /29 provisioned on a network port for a server and am trying to at least configure the machine so I can ssh into it. It's Centos 6.2 x64 with the Basic Server install. Currently not able to ping gateway or any address for that matter. For reference: Default Interface: em2 Network ID: 66.*.*.0/29 Gateway: 66.*.*.1 Broadcast: 66.*.*.7 Please see my following configs: /etc/sysconfig/network-scripts/ifcfg-em2 DEVICE=em2 NM_CONTROLLED=yes ONBOOT=yes HWADDR=Not Important TYPE=Ethernet BOOTPROTO=none IPADDR=66.*.*.2 PREFIX=29 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System em2" NETMASK=255.255.255.248 USERCTL=no $: route -n Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 0.0.0.0 255.255.255.248 U 0 0 0 em2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 1003 0 em2 0.0.0.0 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: route Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 * 255.255.255.248 U 0 0 0 em2 link-local * 255.255.0.0 U 0 1003 0 em2 default 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=excalibur.domain.com GATEWAY=66.*.*.1 Keep in mind that I cannot even currently ping the gateway which is quite confusing for me. My /etc/hosts are configured correctly with the *.2 address. I'm not concerned with getting all of the addresses on the /29 up and running yet, just one so I can at least ssh in. Thanks! Edit: Adding in ifconfig. $: ifconfig em2 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX inet addr:66.*.*.2 Bcat:66.*.*.7 Mask:255.255.255.248 inet6 addr: UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5536 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2599469 (2.4 MiB) TX bytes: 748 (748.0 b) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 etc etc

  Read the article

• USB Flash Drive Problem!

  - by Daren

  Here it goes. My friend saved by his works into my flash drive which was detectable/openable but ... The very next day, the drive wouldn't show up in My Computer and Windows gave him error code 43 (Unknown device). I been searching for the next few hours to find a solution as the works inside is important to him. I know he should back up his files but let's not go there. So .... I tried others few systems that once detected his flash drive but the problem still persisted. I don't know whether or not his flash drive is damaged but when plug/un-plugging, there are still sounds coming out though. Tried solutions: [On Vista Home Premium/HIS COME]Uninstalled -- Restarted com -- Re-installed (ERROR 43) [Windows 7/MY COM] Uninstalled --- Restarted com --- Can't install (ERROR 43) It seems that my com (Windows 7) had the lastest drivers already but still can't detect it. Its a Kingston DataTraveller 101 (DT101) 8GB. Could unplugging the flash drive without clicking "Safely Remove Hardware" is the problem? Kindly provide some help. Thank you all.

  Read the article

• tftpd-hpa service must be restarted before working after fresh boot

  - by Steve

  I'm running Ubuntu 12.04 inside a VirtualBox VM. I've installed tftpd-hpa so I can boot an embedded Linux device via tftp. My problem is that after a fresh boot of the VM, tftpd doesn't seem to work until I restart the service, after which is works great until the system is rebooted. The transcript below should explain the situation. EDIT: After the fresh boot, I execute netstat -a | grep tftp and find nothing. After restarting the service, the same command returns udp 0 0 *:tftp *:* (whitespace removed). I think this might be the key to the problem, I'm just not sure how to resolve it. I don't think it's related to this specific issue, but I had another problem with tftpd that was asked and answered in this question. steve@steve-VirtualBox:~$ cat /etc/default/tftpd-hpa # /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY="/var/lib/tftpboot" TFTP_ADDRESS="0.0.0.0:69" TFTP_OPTIONS="--secure" steve@steve-VirtualBox:~$ ls -l /var/lib/tftpboot total 8204 -rw-r--r-- 1 root root 34352 May 28 08:22 am335x-boneblack.dtb -rw-r--r-- 1 root root 33206 May 28 08:22 am335x-bone.dtb -rw-r--r-- 1 root root 41564 May 28 08:22 am335x-evm.dtb -rw-r--r-- 1 root root 38048 May 28 08:22 am335x-evmsk.dtb -rwxr-xr-x 1 root root 4117904 May 20 09:39 zImage -rw-r--r-- 1 root root 4117616 May 28 08:22 zImage-am335x-evm.bin steve@steve-VirtualBox:~$ tftp localhost tftp> get zImage Transfer timed out. tftp> quit steve@steve-VirtualBox:~$ sudo service tftpd-hpa restart [sudo] password for steve: tftpd-hpa stop/waiting tftpd-hpa start/running, process 2106 steve@steve-VirtualBox:~$ tftp localhost tftp> get zImage Received 4143798 bytes in 1.4 seconds tftp> quit steve@steve-VirtualBox:~$

  Read the article

< Previous Page | 532 533 534 535 536 537 538 539 540 541 542 543  | Next Page >