Search Results

Search found 18151 results on 727 pages for 'upside down'.

Page 536/727 | < Previous Page | 532 533 534 535 536 537 538 539 540 541 542 543  | Next Page >

• Cloning to a smaller hard drive with DDRescue

  - by krebshack

  I am currently working with a 700 GB Seagate hard drive that's beginning to fail. I'll call this "SDB" from now on. I'd like to clone it while I'm still able to. However, the only hard drive that I have available is a 500 GB WD hard drive. I'll call this "SDC" from now on. The partition scheme on SDB is as follows: 9.77 GB is allocated to a recovery partition and the remaining 688.87 GB is allocated to a Windows partition. Both are formatted using NTFS. There is no partition scheme on SDC. I know how to clone one hard drive to another using DDRescue but I've only done it using hard drives that are the same size. For your reference, I'll normally use the command "ddrescue -v -r 3 /dev/sdb /dev/sdc example.log". I'd like to know if it's possible to do this with DDRescue. I've read the manual from GNU (http://www.gnu.org/software/ddrescue/manual/ddrescue_manual.html) and I haven't seen anything indicating that it is possible. I'm just looking for some confirmation that this is a correct impression. If it's not possible, then it would be helpful if any of y'all would be able to make some work around suggestions. But please don't feel obligated to do that. I don't want to have my one thread bogged down with two many questions.

  Read the article

• INACCESSIBLE_BOOT_DEVICE after installing Linux on same drive

  - by kdgregory

  History: My PC was configured with two drives: an 80G on IDE 0 Primary that was running Win2K, and a 320G on IDE 0 Secondary that was running Linux (Ubuntu). I decided to pull the 80Gb drive out of the system, so dd'd the entire 80 G drive (/dev/sda) onto the 320 (/dev/sdb) -- this included the MBR and partition table. Then I pulled the drive, plugged the 320 into IDE 0 Primary, and rebooted. The Windows partition worked at this point. Then I installed Ubuntu into the remaining space on the 320. It works. However, when I try to boot into Windows, I get a BSOD with the following message: *** STOP: 0x0000007B (0x89055030,0xC000014F,0x00000000,0x00000000) INACCESSILE_BOOT_DEVICE Before the BSOD I see the Win2K splash screen, and it claims to be "starting windows" for a couple of seconds -- so it appears that the first stage boot loader is working as expected. Ditto when I try booting in Safe Mode. After reading the Microsoft KB article, I booted into the recovery console and tried running chkdsk /r. It refused to run, claiming that the drive was corrupted (sorry, didn't write down the exact error message). However, I can mount the drive from Linux, and access all files. And for what it's worth, I can scan the drive using the Linux "Disk Utility" (this is Ubuntu, the menus don't show real program names), it claims the drive to be clean. The KB article mentioned that boot.ini could be the problem, so here it is: timeout=10 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows 2000 Professional" /fastdetect Any pointers on what to do next?

  Read the article

• Understanding Unix Permissions (w/ ACL)

  - by Dr. DOT

  I am trying to set permissions on my server properly. Currently I have a number of directories and files chmod'd at 0777 -- but I am not comfortable with it being this way. So at the advice of a serverfault specialist, I had my hosting provider install ACL on my shared virtual server. When I FTP to the server as my FTP user account "abc", I can do everything I need to do (and rightfully so) because all my dirs and files are owned by "abc", the group is "abc", and the 1st octet is set to 7 (rwx). That much I get. But here's where it gets dark gray for me. PHP is set to user "nobody". so when someone browses on of my web pages that either ends in .php or has some embedded PHP, I assume the last octet controls the access. Because all my dirs and files are owned by "abc" and assigned to group "abc", if the last octet was a 4 (r--) then the server would let the browser read the file. If it were a 6 (rw-) then the server would let the browser also write to the file or directory, correct? what if the web document does not end in .php or does not have any PHP embedded? What is the user then? how can I use ACL to not set the permission to 6 (rw-) or even 7 (rwx)? [not sure what execute does or means] Just looking for some sort of policy settings to best lock down my dirs and files while allowing my PHP scripts to do uploads and write to files (so my users don't call me to tell me "permission denied". Ok, thanks to anyone out there willing to lend me a hand. It is greatly appreciated.

  Read the article

• Monitor attached to motherboard is out of frequency

  - by Neilvert Noval

  I don't know if this is appropriate to ask it here in superuser. Please, just route this to appropriate stackexchange site if found unrelevant. Here's my scenario. I have bought a new motherboard (MSI 785GT-E63). I already have an old CRT monitor connected to it. After I install a linux OS to it, my monitor will display that it is: Out of frequency. Current frequency is 89Hz. The operating output of my monitor is (around) 60-70Hz. I would like to get this thing work. How can I let my CRT display properly? I was thinking of lowering down video frequency output of my motherboard, but I can't find any settings on my BIOS setup. Additional info: My monitor is attached directly to the built-in video adaptor of my motherboard. (No additional video cards) Install of OS is complete without errors. Please help.

  Read the article

• Exchange migration: ExchangeTransport warnings after uninstalling source server

  - by carlpett

  After disabling/uninstalling Exchange from our source SBS2003 server, I'm getting these warnings: Event 5020 "The topology doesn't contain a route to Exchange 2000 Server or Exchange Server 2003 sourceserver.domain.local in Routing Group [...]" Event 5006 "Cannot find route to Mailbox Server CN=SOURCESERVER [...] for store CN=[...]", for Public folder, First storage group and Recovery storage group. I followed the technet article here: http://technet.microsoft.com/en-us/library/bb288905.aspx (linked from the SBS 2003 - 2011 migration guide). When uninstalling Exchange, I got a warning about NNTP not being found in the registry, but that didn't seem relevant, and the uninstall continued. The server was subsequently removed from the domain and shut down, as per the instructions. If I open the Public Folder Management console on the Exchange 2010 server, the public folders \NON_IPM_SUBTREE\EFORMS_REGISTRY and \Archived mails gives an error on "Update content". I haven't found anything else which indicates something is wrong. We never really used the public folders on the old server, so there isn't really anything lost. Can I just remove these folders and let them be created anew?

  Read the article

• Thunderbird: export email account settings

  - by zpea

  I'd like to create a new profile for Thunderbird using the same mail accounts I already configured in my old profile. As it is quite a number of accounts, it would be great to have a way to export/import them instead of writing down the settings just to fill in again in the new profile. Using web search and search here I mainly found following suggestions that do not match what I need: Copy the whole profile: Not possible for me as I don't want to copy other settings, the downloaded mail data etc. and the old profile broke when running out of space in the home folder anyway. Use mozBackup: There seem to be several programs by that name (forks?). In any case, it's Windows-only and hence no option (I am mostly on Linux and prefer platform-independent solutions anyway) Use accountex: Seems to do what I want, but it is not compatible with current Thunderbird version (supports only up to version 3.1) Posts with various tips from 4 years ago: Top results in the web search with the G. But they do not work in current versions of Thunderbird either. Did I overlook anything? After all, it doesn't sound like I was looking for something nobody ever looked for.

  Read the article

• NFS on top of GFS2 - does it work?

  - by Matthew

  We're currently using a NoSQL derivative called Splunk to receive our data. The software supports something called "search head pooling" in which the job-dispatching engine is housed on several servers which share a common storage point. Originally our intention was to use a clustered filesystem like GFS2 because of low latency, stability, and ease of setup. We set up GFS2, and it's working with no issues. However when trying to run the software, it's trying to create lock files, and a bunch of other things that their support team can't quite explain. Ultimate feedback from them was that they only support NFS. Our network administration team heavily frowns on NFS (lack of stability, file lock issues, etc). So, I was thinking about the possibility of setting up NFS on each server in the cluster to act as a wedge layer between the GFS2 filesystem and the software. Basically configure each server to export the GFS2 filesystem's mountpoint via NFS, and then tell each server to connect to that NFS share. That way we aren't introducing any single-points-of-failure should a dedicated NFS server go down, but the vendor gets their "required" NFS share. I'm just brainstorming ways around, so please tear this apart :)

  Read the article

• Does a high run queue length average result in poor performance for a web server?

  - by Domino

  I'm trying to narrow down the list of suspects of web servers that perform moderately well most of the time with occasional bouts of poor performance. I'm analyzing the data collected and summarized by sar. I've noticed a few things, one of which is high number of tasks in the run queue. 10:15:01 AM runq-sz plist-sz ldavg-1 ldavg-5 ldavg-15 blocked 10:25:01 AM 2 150 0.05 0.05 0.06 0 10:35:01 AM 4 149 0.08 0.12 0.09 0 10:45:01 AM 6 150 0.13 0.19 0.15 0 10:55:01 AM 1 150 0.08 0.10 0.13 0 11:05:01 AM 4 150 0.20 0.35 0.23 0 11:15:01 AM 3 149 0.02 0.09 0.15 0 11:25:01 AM 7 149 0.04 0.05 0.11 0 11:35:01 AM 4 150 0.14 0.15 0.13 0 11:45:01 AM 6 150 0.27 0.18 0.16 0 11:55:01 AM 5 150 0.08 0.10 0.13 0 12:05:01 PM 3 149 0.35 0.40 0.26 0 12:15:01 PM 19 155 0.02 0.10 0.16 1 12:25:01 PM 2 150 0.00 0.07 0.12 0 12:35:02 PM 3 151 0.58 0.24 0.17 0 12:45:01 PM 8 150 0.02 0.13 0.15 0 12:55:01 PM 6 149 0.81 0.29 0.18 0 01:05:01 PM 3 148 0.00 0.09 0.13 0 01:15:01 PM 7 149 0.00 0.04 0.11 0 I believe these are 10 minute averages. Is this an indicator that the web server is not performing as fast as it could if the average run queue length was lower?

  Read the article

• troubleshooting really slow login on a (linux) machine

  - by Peeter Joot

  Within the last couple of weeks, any attempt to login to a specific linux server has gotten really slow. Once I've logged in, things appear to run without significant delay, but some other login like activities (like starting a new screen session) are slow. The machine's been rebooted a couple of times recently and that hasn't helped. , and it doesn't appear to be $PATH search (where $PATH can sometimes include bad NFS mounts), which I've seen historically in our environment. I've also tried completely removing my .profile/.bash*/... type of init files to rule out anything bad there. I also see slow login for at least one other userid on the system. One thing I've noticed is the following message when trying to exit from a screen terminal: Utmp slot not found -> not removed and am wondering if this is related (having a vague recollection that Utmp has something to do with login). Any idea what that message means, or how to fix it, and if it would be related? Failing that, what sort of problem determination tools are available to investigate what is slowing down this login process?

  Read the article

• DBCC CHECKDB fails and quits job, ambiguous error message.

  - by ddono25

  I received a notice that one of our servers' DBCC CHECKDB for all databases has been failing the past four times it has been run. We don't have any data prior to that, but it doesn't look like it has been succeeding for awhile. There are no errors in the log file only: DBCC results for 'sys.sysxmlfacet'. [SQLSTATE 01000] Msg 0, Sev 0, State 1: Unspecified error occurred on SQL Server. Connection may have been terminated by the server. [SQLSTATE HY000] There are 112 rows in 1 pages for object "sys.sysxmlfacet". [SQLSTATE 01000] I ran a DBCC CHECKDB using sp_MSForEachDB to get more accurate results and had the same error on the same DB but at a separate point: DBCC results for 'NameValuePair_Greek_CI_AS'. [SQLSTATE 01000] Msg 0, Sev 0, State 1: Unspecified error occurred on SQL Server. Connection may have been terminated by the server. [SQLSTATE HY000] There are 0 rows in 0 pages for object "NameValuePair_Greek_CI_AS". [SQLSTATE 01000] Also, the error-log states that the DBCC completed without errors for this database. I can't figure out how to track down this ambiguous issue that only happens on this database out of the dozens on this server. Any help is appreciated!

  Read the article

• Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

  - by Maxim Z.

  I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

  Read the article

• What are the typical methods used to scale up/out email storage servers?

  - by nareshov

  Hi, What I've tried: I have two email storage architectures. Old and new. Old: courier-imapds on several (18+) 1TB-storage servers. If one of them show signs of running out of disk space, we migrate a few email accounts to another server. the servers don't have replicas. no backups either. New: dovecot2 on a single huge server with 16TB (SATA) storage and a few SSDs we store fresh mails on the SSDs and run a doveadm purge to move mails older than a day to the SATA disks there is an identical server which has a max-15min-old rsync backup from the primary server higher-ups/management wanted to pack in as much storage as possible per server in order to minimise the cost of SSDs per server the rsync'ing is done because GlusterFS wasn't replicating well under that high small/random-IO. scaling out was expected to be done with provisioning another pair of such huge servers on facing disk-crunch issues like in the old architecture, manual moving of email accounts would be done. Concerns/doubts: I'm not convinced with the synchronously-replicated filesystem idea works well for heavy random/small-IO. GlusterFS isn't working for us yet, I'm not sure if there's another filesystem out there for this use case. The idea was to keep identical pairs and use DNS round-robin for email delivery and IMAP/POP3 access. And if one the servers went down for whatever reasons (planned/unplanned), we'd move the IP to the other server in the pair. In filesystems like Lustre, I get the advantage of a single namespace whereby I do not have to worry about manually migrating accounts around and updating MAILHOME paths and other metadata/data. Questions: What are the typical methods used to scale up/out with the traditional software (courier-imapd / dovecot)? Do traditional software that store on a locally mounted filesystem pose a roadblock to scale out with minimal "problems"? Does one have to re-write (parts of) these to work with an object-storage of some sort - such as OpenStack object storage?

  Read the article

• DFS Root namespace is RDWR for all users

  - by Patrick

  We have an existing DFS Replication and Namespace group that we use to serve the company's files. This has been operating fine for us for some time now, and continues to do so. however a situation arose yesterday afternoon that has led us to be stumped. The problem is that we have our name space presented as : \\domain.co.uk\public\[8 or 9 folders that are mapped to the users in the business] We had a problem this morning that meant that a number of users started mapping their AD Home Drive directly to the \\domain.co.uk\public directory and we found that they had read/write. This rapidly became a problem as a at least one director saved some moderately sensitive documents in there and basically anyone could read them. I've tidied up that specific problem with some deft scripting and a slight modification of group policy. However I would like to make \public read only, the trouble is I can't work out where the ACLs for that folder would be held. All the folders that are presented as \\domain.co.uk\public\[folder] are 'real' folders on logical volumes on our DFS servers so are secured with groups that are applied via the 'security' tab. I'd like to do the same on \public but I can't find it. I have looked through amongst other things \Sysvol\domain.co.uk but can't find it and after a lot of clicking and a bit of reading I can't see how to lock it down. Any thoughts?

  Read the article

• What's Keeping My Computer Awake?

  - by phantomdata

  First the question; How do I figure out what is preventing my Windows 7 computer from going into sleep mode? Second; some background... I've been struggling with this for a few days and am utterly perplexed. I setup sleep mode on my Windows 7 PC a few weeks ago, and all was well. The PC would sleep as expected and I was snuggly in knowing that my computer was saving power and some wear and tear on the components (we'll leave the 'is it better to sleep' debate for another thread/day, please don't start it). Well, I noticed the other night that my system stopped ever going to sleep. I set the sleep time down to 1 minute and wandered fully away from the PC (ensuring that no errant mouse or keyboard movements would occur) and the PC never went to sleep. I've also observed this over longer intervals as well, such as overnight. I have sleep mode enabled, of course "multimedia settings - When Sharing Media" is set to allow the computer to sleep. "powercfg -lastwake" show nothing of interest, since it never goes to sleep and can't wake up. "powercfg /requests" shows 3 entries - all "[DRIVER] ?". I assume that 2 of these are my mouse and keyboard - as I've recently used them to run the powercfg command. I'm at a loss for the third though. I've unhooked all USB peripherals save for my keyboard and mouse. Wake on LAN is disabled in my BIOS. I know that you can disable all apps from waking/preventing sleep - but I want the ability to remain for those apps that do legitimately need to keep the system awake. So; does anyone know of a way to figure out what the 3rd phantom "[DRIVER] ?" is in powercfg /requests?

  Read the article

• Stronger laptop_mode in Linux

  - by Vi

  Can I have stronger laptop mode in Linux? I want to spin down the hard drive and prevent it to spin up even if something wants to read something not in cache. In general I want to have these modes: Normal Current laptop mode Stronger laptop mode: spin up only when needs to read something uncached (and cache it). No spinups to write something unless really memory pressure (Exception: explicit "sync" command in console). Kernel is allowed to keep processes in D-sleep for 10 seconds for that. Forced laptop mode: do not spin up, period. Keep offending processes in D-sleep unless I turn off this mode. Like there is a bomb instead of hard drive. I also want to have access times tracked (mount -o atime), but I don't want the hard drive to be spinned up only to update them. Is there some settings or kernel patches that can get closer to this? May be I should write special io scheduler for "forced laptop mode"? E.g. echo suspend > /sys/block/sda/queue/scheduler to lock the drive and echo cfq > /ys/block/sda/queue/scheduler to unlock it again?

  Read the article

• How can I read PDFs with e-reader on a Lenovo tablet?

  - by Jack M

  This is my first time using a tablet and I'm totally lost - this must be what computers look like to old people. This is a Lenovo Thinkpad tablet. I don't see a specific model number on it (it was passed down to me second hand). What I'd like to do is read a PDF. I'm fairly certain I successfully transferred the PDF onto the tablet via an SD card, and I noticed this thing has an app called "eReader" on it, so I started that up. All I see are empty bookshelves, and no obvious buttons or settings anywhere. I saw in multiple places that you have to, as one site puts it: ...copy and paste the relevant files into the eBooks folder and they will appear on the eReader shelf for your consumption... But I have no idea how to: Access the file system. Locate the eBooks folder. Copy and paste files. Will I need a file explorer app? If so, how can I install that given that my only method of getting data onto this tablet is an SD card (no wireless internet).

  Read the article

• How to automatically start VM created by virt-manager?

  - by Jeff Shattock

  I have created a virtual machine with virt-manager that runs on kvm/qemu. The machine works well when started through virt-manager. However, I would like to be able to start and stop the VM through a script in init.d, so that it comes up and down along with the host. I need to have virt-manager show that the machine is running, and to be able to connect to its console through there. When I use the command line that is produced by running ps -eaf | grep kvm after starting the vm through virt-manager, I get some console messages about redirected character devices, but the machine does start and runs properly. However, I do not get any indication from virt-manager that it has started. How can I modify the command line to get virt-manager to pick up the running VM? Is there anything else about the command line that should change when starting outside of virt-manager? Command line is (slightly reformatted for readability): /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1 -name BORON \ -uuid fa7e5fbd-7d8e-43c4-ebd9-1504a4383eb1 \ -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/BORON.monitor,server,nowait \ -monitor chardev:monitor -localtime -boot c \ -drive file=/dev/FS1/BORON,if=ide,index=0,boot=on,format=raw \ -net nic,macaddr=52:54:00:20:0b:fd,vlan=0,name=nic.0 \ -net tap,fd=41,vlan=0,name=tap.0 -chardev pty,id=serial0 -serial chardev:serial0 \ -parallel none -usb -usbdevice tablet -vnc 127.0.0.1:1 -k en-us -vga cirrus

  Read the article

• Linux 2.6.24-gentoo-r3-comtrance on x86_64 high Useage for unknown reasons

  - by Dorjan

  Hello everyone, I'm a complete rookie when it comes to all things Linux related so please treat me as such and assume I know nothing. That being said my Top says this: top - 12:08:03 up 11 days, 15:36, 0 users, load average: 5.47, 5.53, 5.46 Tasks: 296 total, 2 running, 294 sleeping, 0 stopped, 0 zombie Cpu(s): 6.3%us, 1.4%sy, 0.0%ni, 71.3%id, 20.6%wa, 0.0%hi, 0.3%si, 0.0%st Mem: 8176880k total, 8118236k used, 58644k free, 89312k buffers Swap: 1004052k total, 0k used, 1004052k free, 7235652k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1229 root 15 -5 0 0 0 D 1 0.0 199:28.63 kjournald 2946 root 20 0 1716 676 552 D 1 0.0 145:02.94 syslogd 14553 root 20 0 2644 1268 876 R 1 0.0 0:00.34 top 14609 postfix 20 0 7896 1884 1460 D 1 0.0 0:00.02 bounce 14630 postfix 20 0 7896 1876 1452 R 0 0.0 0:00.00 bounce And my hard drives says: > df -k Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda3 4925556 4474836 200508 96% / /dev/sda5 489992 36090 428602 8% /tmp /dev/sda6 377951852 236171160 122581816 66% /var none 4088440 0 4088440 0% /dev/shm It has been like it for a few days now... I know not what is causing the high server load (Normally around 1.3) can anyone give any tips on how to track down the culprit? Many thanks,

  Read the article

• Need help ttoubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after rstarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What i have done: I thought it was HDD at first, since this is the only part of the coputer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from bootable USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD apears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoughrouly. The problem still persists, what should my next steps be? Thanks in advance.

  Read the article

• Laptop + External Monitor: Possible to Scale Mouse-crossover Position?

  - by Brian Lacy

  I have a laptop with a 16" screen @ 1366x768 resolution, and a 24" external monitor at 1920x1200 resolution. I'm extending the Windows 7 desktop onto the other screen. The 24" is the secondary monitor, and is positioned so the bottom of that screen lines up with the bottom of the 16" screen. Currently, if I move the mouse to the top portion of the 24" screen, then move left, the mouse will stop at the edge of the 24" screen until I move it down far enough to get into the range of the 16" screen. So that's all pretty standard; but I'm wondering if there's any software out there that will allow me to "scale" the mouse-crossover position, such that if I'm at the TOP of the 24" screen and move left, the mouse will cross to the TOP of the 16" screen, whereas if I'm at the BOTTOM of the 24" screen, crossing over will position the mouse at the BOTTOM of the 16" screen. So then, if the mouse cursor is on the 24" screen at (x,y) position (10,600), and I move 20 pixels left, the mouse is now on the 16" screen at position (1356,384). Anyone know of such a solution?? Note: I also use Ubuntu, so if there's a solution to this for X, but not Windows, I'd be interested in that also.

  Read the article

• Switch between network configurations via command line in fedora 17

  - by Mike Fairhurst

  I have two different setups I use on my work laptop; one enables synergy over an ethernet ssh tunnel with my work computer on the local network, and the other opens an HTTP tunnel to my work computer from outside the network. When I have wifi enabled at work, my laptop seems to use it by preference. This makes synergy run incredibly slowly. At home I must use wifi. I have scripts that begin my ssh tunnels, add my ssh keys, and starts up other programs like synergy, and close themselves when I shut my laptop. However, every day I have to start out my routine by opening my gnome-control-center and turning on my ethernet. I have tried route add and ifup, none of it works, so I dove into gnome-control-center's source code and found that it enabled the connection by libnm's method nm_client_activate_connection with some libnm specific structs that I am having trouble tracking down. I'm not much of a c programmer, and I'm not familiar with either GTK or libnm. Does anybody know what fedora 17 does with ethernet connections to fully enable them? Or does anybody know what libnm does to fully enable an ethernet connection? Do I have to write a c script to run libnm for me to fully emulate whatever gnome-control-center is trying to do?

  Read the article

• Server Intermittently Inaccessible Externally (but Accessible Internally Continuously)

  - by nicorellius

  I have a CRM on a server on a network. We have a static IP and another server outward facing. We use port-forwarding to map to the CRM, so that when you go to the IP or the FQDN, you get to the CRM: xxx.xxx.xxx.xxx crm.example.com Internally, we can access the CRM by going to crm or crm.example.com Lately, I've been noticing that accessing the server from outside the network times out or gives 503, bad gateway. During that time, I can also SSH (different port, so this works) into the outward facing computer and access the server just fine. I have a robot monitoring the site and indeed via HTTP monitoring the site is going down periodically. I looked through the Apache server access and error logs and nothing stuck out at me so I'm a bit confused as to what could be going on. I also searched the access logs for 503 and found nothing. When I run tracert from outside the network, it appears the packets basically make it through the wider area servers (Comcast city and county servers) and end up dropping at the CRM server's front step. I'm tempted to replace the server because it is older and underpowered but it would be nice to know what is going on. Any ideas what to do next?

  Read the article

• Strange WiFi problem - network is "not connected" but works

  - by GalacticCowboy

  Background I'm using a Windows XP tablet PC connected to my home network. I do broadcast the SSID, but otherwise the wireless network is locked down as tight as I can make it - WPA2 with a strong key, MAC filtering, etc. I've had this computer for about 4 years and the router for about 6 months. Before that, the previous router was set up in the same way, and I've never had any particular problems. Problem This morning - as I type this, as a matter of fact - Windows is reporting that none of my network connections are connected. Yet somehow my Internet connectivity still works! ipconfig reports a valid IP address, domain, etc., even though Windows apparently doesn't know about it. I tried repairing the connection and it had no effect - the repair eventually timed out. I'm pretty sure that I could reboot the computer and/or the router, etc. and it would fix the problem. However, I'm more interested in knowing if any of you have ever seen anything like this, and what might have caused it? Since it works I'm not inclined to mess with it too much. My concern is that it's a precursor to bigger problems.

  Read the article

• Enterprise Redirection Services?

  - by Aaron Alton

  This is probably a case of "if I new what it was called, I could google it in 5 minutes" - but I don't know what it's called. It's probably best to explain the requirement using an example. We have a number of services (vpn, owa, etc) which we host from one of our datacenters. We have a number of datacenters, and we technically have the infrastructure already in place to support these services at a number of our datacenters. To provide access to these "services", I would create an external DNS entry (ex. VPN.MyCompany.com Gateway IP for one of my DCs), and clients will connect to it via the DNS entry. Since I have multiple datacenters that can support this service, I could theoretically offer a "highly available, geographically dispersed" solution if I could point this DNS entry to some sort of third party who offers highly available "redirection" services. If my primary site goes down, I could just make a change via some management console and configure the redirector to point to a different DC. Of course, it would be fairly straightforward to set this sort of thing up on one of our servers, but that would kinda defeat the purpose of a highly available third party. Is anyone familiar with a service like this? I'm thinking something like DynDNS, but with Enterprise availability guarantees.

  Read the article

• Switched to new router and now experiencing lag?

  - by Mr_CryptoPrime

  I switched from a dynex-802.11b/g to a Netgear-802.11b/g/n just yesterday. My router is down stairs because my phoneline upstairs is retarded....but my PS3 is still upstairs (SOCOM: Confrontation is game I am experiencing issues). I have done everything I can to make sure the connection is solid and have checked the status and it has been as high as 80% and usually lingers at about 60%. I thought about upgrading my bandwidth from 1.5mbs to 7mbs, but I am guessing something is wrong if it worked fine before? Now the game seems more laggy and my voice chat is choppy. Others seem to receive my voice data fine because I can hear my own feedback clearly from other players (if you are in close proximity to another player and speak and there volume is loud enough sometimes you can hear yourself). I wonder if I port forward or setup DMZ then it will be fixed, but I am not sure and don't know quite how to do it. Has anyone else ever experienced this when switching routers? What did you do to fix it? Thanks!

  Read the article

< Previous Page | 532 533 534 535 536 537 538 539 540 541 542 543  | Next Page >