Search Results

Search found 1582 results on 64 pages for 'packet snifers'.

Page 54/64 | < Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >

• What's wrong with my wireless?

  - by dazzle

  I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

  Read the article

• Wireless connection works but the internet is too slow to use in Ubuntu 11.04

  - by Garrin

  The internet is so slow as to be unusable. And I'm not being picky. Even after minutes I can't get my Google home page to load. I tried installing a package through apt-get and was getting rates between 0 and a few hundred bytes/s. That's bytes, not kilobytes! Mostly 0 however (no exaggeration, it spends large amounts of time stalled). And I would go to a speed test web site of some kind but I can't since nothing will load. Briefly put, the laptop I am using was connected to two wireless networks while using Ubuntu 11.04 without any issues before this. It was also connected to a wired network without any issues. It dual boats Windows 7 which has never had any issues, not even with the current wireless network. Just to be clear, on the current wi-fi network, Windows 7 encounters no issues (speedtest.net puts the network speed at 1mb/s) but my network connection in Ubuntu 11.04 is so slow as to literally be unusable. I am unfamiliar with the router except for the fact that it boasts a Rogers logo (that's a large ISP/cable provider in Canada for those not familiar with the land of igloos and polar bears). I am far from the router and some desktop widget I use tells me the signal strength is at 58% (it seems fairly reliable and this would appear to match up with the filled bars in the network icon). I should also mention I'm just renting a room in this house so I'm not the network administrator and while I can access the 192.168.0.1 router page, the password wasn't set to 'password' so it's not much use to me. Here are a bunch of commands I ran which don't tell me a whole lot but I thought might be more instructive to the wise around here: lspci (just showing my network card): 05:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) This one is self explanatory. PING www.googele.com (216.65.41.185) 56(84) bytes of data. 64 bytes from nnw.net (216.65.41.185): icmp_req=1 ttl=51 time=267 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=2 ttl=51 time=190 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=3 ttl=51 time=212 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=4 ttl=51 time=207 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=5 ttl=51 time=220 ms --- www.googele.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4003ms rtt min/avg/max/mdev = 190.079/219.699/267.963/26.121 ms ifconfig eth0 Link encap:Ethernet HWaddr 20:6a:8a:02:20:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:960 (960.0 B) TX bytes:960 (960.0 B) wlan0 Link encap:Ethernet HWaddr 20:7c:8f:05:c6:bf inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::227c:8fff:fe05:c6bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:982 errors:0 dropped:0 overruns:0 frame:0 TX packets:658 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:497250 (497.2 KB) TX bytes:95076 (95.0 KB) Thank you

  Read the article

• SQL Server - Physical connection is not usable Error Code: 19

  - by Harry

  Having trouble working out this SqlException: A transport-level error has occurred when sending the request to the server. (provider: Session Provider, error: 19 - Physical connection is not usable) Any ideas what this is about? Couldn't get any hits on google or msdn on this one. The connection is MARS and Asynchronous in my own SQL pool. But don't get all excited about that - that is old code that has been stable for a long time! Exception details pasted below: System.Data.SqlClient.SqlException occurred Message=A transport-level error has occurred when sending the request to the server. (provider: Session Provider, error: 19 - Physical connection is not usable) Source=.Net SqlClient Data Provider ErrorCode=-2146232060 Class=20 LineNumber=0 Number=-1 Server=SERVER State=0 StackTrace: at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning() at System.Data.SqlClient.TdsParserStateObject.SNIWriteAsync(SNIHandle handle, SNIPacket packet, DbAsyncResult asyncResult) at System.Data.SqlClient.TdsParserStateObject.WriteSni() at System.Data.SqlClient.TdsParserStateObject.WritePacket(Byte flushMode) at System.Data.SqlClient.TdsParserStateObject.ExecuteFlush() at System.Data.SqlClient.TdsParser.TdsExecuteRPC(_SqlRPC[] rpcArray, Int32 timeout, Boolean inSchema, SqlNotificationRequest notificationRequest, TdsParserStateObject stateObj, Boolean isCommandProc) at System.Data.SqlClient.SqlCommand.RunExecuteReaderTds(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, Boolean async) at System.Data.SqlClient.SqlCommand.RunExecuteReader(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, String method, DbAsyncResult result) at System.Data.SqlClient.SqlCommand.InternalExecuteNonQuery(DbAsyncResult result, String methodName, Boolean sendToPipe) at System.Data.SqlClient.SqlCommand.BeginExecuteNonQuery(AsyncCallback callback, Object stateObject) at CrawlAbout.Library.SQL.SQLAdapter.<ExecuteNonQueryTask>d__12.MoveNext() in D:\Work\Projects\CrawlAbout.com 2.0\CrawlAbout.Library.SQL\SQLAdapter.cs:line 149 InnerException:

  Read the article

• MSSQL - Physical connection is not usable Error Code: 19

  - by Harry

  Having trouble working out this SqlException: A transport-level error has occurred when sending the request to the server. (provider: Session Provider, error: 19 - Physical connection is not usable) Any ideas what this is about? Couldn't get any hits on google or msdn on this one. The connection is MARS and Asynchronous in my own SQL pool. But don't get all excited about that - that is old code that has been stable for a long time! Exception details pasted below: System.Data.SqlClient.SqlException occurred Message=A transport-level error has occurred when sending the request to the server. (provider: Session Provider, error: 19 - Physical connection is not usable) Source=.Net SqlClient Data Provider ErrorCode=-2146232060 Class=20 LineNumber=0 Number=-1 Server=SERVER State=0 StackTrace: at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning() at System.Data.SqlClient.TdsParserStateObject.SNIWriteAsync(SNIHandle handle, SNIPacket packet, DbAsyncResult asyncResult) at System.Data.SqlClient.TdsParserStateObject.WriteSni() at System.Data.SqlClient.TdsParserStateObject.WritePacket(Byte flushMode) at System.Data.SqlClient.TdsParserStateObject.ExecuteFlush() at System.Data.SqlClient.TdsParser.TdsExecuteRPC(_SqlRPC[] rpcArray, Int32 timeout, Boolean inSchema, SqlNotificationRequest notificationRequest, TdsParserStateObject stateObj, Boolean isCommandProc) at System.Data.SqlClient.SqlCommand.RunExecuteReaderTds(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, Boolean async) at System.Data.SqlClient.SqlCommand.RunExecuteReader(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, String method, DbAsyncResult result) at System.Data.SqlClient.SqlCommand.InternalExecuteNonQuery(DbAsyncResult result, String methodName, Boolean sendToPipe) at System.Data.SqlClient.SqlCommand.BeginExecuteNonQuery(AsyncCallback callback, Object stateObject) at CrawlAbout.Library.SQL.SQLAdapter.<ExecuteNonQueryTask>d__12.MoveNext() in D:\Work\Projects\CrawlAbout.com 2.0\CrawlAbout.Library.SQL\SQLAdapter.cs:line 149 InnerException:

  Read the article

• Decoding ima4 audio format

  - by MrDatabase

  To reduce the download size of an iPhone application I'm compressing some audio files. Specifically I'm using afconvert on the command line to change .wav format to .caf format w/ ima4 compression. I've read this (wooji-juice.com) awesome post about this exact topic. I'm having trouble w/ the "decoding ima4 packets" step. I've looked at their sample code and I'm stuck. Please help w/ some pseudo code or sample code that can guide me in the right direction. Thanks! Additional info: Here is what I've completed and where I'm having trouble... I can play .wav files in both the simulator and on the phone. I can compress .wav files to .caf w/ ima4 compression using afconvert on the command line. I'm using the SoundEngine that came w/ CrashLanding (I fixed one memory leak). I modified the SoundEngine code to look for the mFormatID 'ima4'. I don't understand the blog post linked above starting w/ "Calculating the size of the unpacked data". Why do I need to do this? Also, what does the term "packet" refer to? I'm very new to any sort of audio programming.

  Read the article

• MySQL Connection Timeout Issue - Grails Application on Tomcat using Hibernate and ORM

  - by gav

  Hi Guys I have a small grails application running on Tomcat in Ubuntu on a VPS. I use MySql as my datastore and everything works fine unless I leave the application for more than half a day (8 hours?). I did some searching and apparently this is the default wait_timeout in mysql.cnf so after 8 hours the connection will die but Tomcat won't know so when the next user tries to view the site they will see the connection failure error. Refreshing the page will fix this but I want to get rid of the error altogether. For my version of MySql (5.0.75) I have only my.cnf and it doesn't contain such a parameter, In any case changing this parameter doesn't solve the problem. This Blog Post seems to be reporting a similar error but I still don't fully understand what I need to configure to get this fixed and also I am hoping that there is a simpler solution than another third party library. The machine I'm running on has 256MB ram and I'm trying to keep the number of programs/services running to a minimum. Is there something I can configure in Grails / Tomcat / MySql to get this to go away? Thanks in advance, Gav From my Catalina.out; 2010-04-29 21:26:25,946 [http-8080-2] ERROR util.JDBCExceptionReporter - The last packet successfully received from the server was 102,906,722 milliseconds$ 2010-04-29 21:26:25,994 [http-8080-2] ERROR errors.GrailsExceptionResolver - Broken pipe java.net.SocketException: Broken pipe at java.net.SocketOutputStream.socketWrite0(Native Method) ... 2010-04-29 21:26:26,016 [http-8080-2] ERROR util.JDBCExceptionReporter - Already closed. 2010-04-29 21:26:26,016 [http-8080-2] ERROR util.JDBCExceptionReporter - Already closed. 2010-04-29 21:26:26,017 [http-8080-2] ERROR servlet.GrailsDispatcherServlet - HandlerInterceptor.afterCompletion threw exception org.hibernate.exception.GenericJDBCException: Cannot release connection at java.lang.Thread.run(Thread.java:619) Caused by: java.sql.SQLException: Already closed. at org.apache.commons.dbcp.PoolableConnection.close(PoolableConnection.java:84) at org.apache.commons.dbcp.PoolingDataSource$PoolGuardConnectionWrapper.close(PoolingDataSource.java:181) ... 1 more

  Read the article

• Use UdpClient with IPv4 and IPv6?

  - by mazzzzz

  A little while ago I created a class to deal with my LAN networking programs. I recently upgraded one of my laptops to windows 7 and relized that windows 7 (or at least the way I have it set up) only supports IPv6, but my desktop is still back in the Windows xp days, and only uses IPv4. The class I created uses the UdpClient class, and is currently setup to only work with IPv4.. Is there a way to modify my code to allow sending and receiving of IPv6 and IPv4 packets?? It would be hard to scrap the classes code, a lot of my programs rely on this class. I would like to keep the class as close to its original state, so I don't need to modify my older programs, only switch out the old class for the updated one. Thanks for any and all help, Max Send: using System.Net.Sockets;UdpClient tub = new UdpClient (); tub.Connect ( new IPEndPoint ( ToIP, ToPort ) ); UdpState s = new UdpState (); s.client = tub; s.endpoint = new IPEndPoint ( ToIP, ToPort ); tub.BeginSend ( data, data.Length, new AsyncCallback ( SendCallBack ),s); private void SendCallBack ( IAsyncResult result ) { UdpClient client = (UdpClient)( (UdpState)( result.AsyncState ) ).client; IPEndPoint endpoint = (IPEndPoint)( (UdpState)( result.AsyncState ) ).endpoint; client.EndSend ( result ); } Receive: UdpClient tub = new UdpClient (ReceivePort); UdpState s = new UdpState (); s.client = tub; s.endpoint = new IPEndPoint ( ReceiveIP, ReceivePort ); s.callback = cb; tub.BeginReceive ( new AsyncCallback ( receivedPacket ), s ); public void receivedPacket (IAsyncResult result) { UdpClient client = (UdpClient)( (UdpState)( result.AsyncState ) ).client; IPEndPoint endpoint = (IPEndPoint)( (UdpState)( result.AsyncState ) ).endpoint; Byte[] receiveBytes = client.EndReceive ( result, ref endpoint ); ReceivedPacket = new Packet ( receiveBytes ); client.Close(); //Do what ever with the packets now }

  Read the article

• InvalidAuthenticityToken for JQuery despite setting authenticity token

  - by user117046

  I'm getting an InvalidAuthenticityToken despite adding in corresponding authenticity tokens in the jquery response. Is there an error in the code, or is there another, root problem? I appreciate any comments. Thanks! Using: Rails 2.3.3, Ruby 1.8.6, Webrick, JQuery 1.3.2 layout/networks.html.haml = token_tag = javascript_tag "window.AUTH_TOKEN = '#{form_authenticity_token}';" javascripts/application.js $(document).ready(function() { // All non-GET requests will add the authenticity token // if not already present in the data packet $(document).ajaxSend(function(event, request, settings) { if (typeof(window.AUTH_TOKEN) == "undefined") return; // <acronym title="Internet Explorer 6">IE6</acronym> fix for http://dev.jquery.com/ticket/3155 if (settings.type == 'GET' || settings.type == 'get') return; settings.data = settings.data || ""; settings.data += (settings.data ? "&" : "") + "authenticity_token=" + encodeURIComponent(window.AUTH_TOKEN); }); ajaxLinks(); }); The rendered html has: <input name="authenticity_token" type="hidden" value="ZaXj3ACQl+8JKtaDAUoxtSsqzEagSPyHbS25ai9qWCw=" /> <script type="text/javascript"> //<![CDATA[ window.AUTH_TOKEN = 'ZaXj3ACQl+8JKtaDAUoxtSsqzEagSPyHbS25ai9qWCw='; //]]> </script> and breakpointing through, shows that window.AUTH_TOKEN has been set. Any help to resolve this would be great.

  Read the article

• Multiple sendto() using UDP socket

  - by ereOn

  Hi, I have a network software which uses UDP to communicate with other instances of the same program. For different reasons, I must use UDP here. I recently had problems sending huge ammounts of data over UDP and had to implement a fragmentation system to split my messages into small data chunks. So far, it worked well but I now encounter an issue when I have to send a lot of data chunks. I have the following algorithm: Split message into small data chunks (around 1500 bytes) Iterate over the data chunks list and for each, send it using sendto() However, when I send a lot of data chunks, the receiver only gets the first 6 messages. Sometimes it misses the sixth and receives the seventh. It depends. Anyway, sendto() always indicates success. This always happen when I test my software over a loopback interface (127.0.0.1) but never over my LAN network. If I add something like std::cout << "test" << std::endl; between the sendto() then every frame is received. I am aware that UDP allows packet loss and that my frames might be loss for a lot of reasons and I suppose it has to do with the rate I am sending the data chunks at. What would be the right approach here ? Implementing some acknowledgement mechanism (just like TCP) seems overkill. Adding some arbitrary waiting time between the sendto() is ugly and will probably decrease performance. Increasing (if possible) the receiver UDP internal buffer ? I don't even know if this is possible. Something else ? I really need your advices here. Thank very much.

  Read the article

• Flush kernel's TCP buffer with `MSG_MORE`-flagged packets

  - by timn

  send()'s man page reveals the MSG_MORE flag which is asserted to act like TCP_CORK. I have a wrapper function around send(): int SocketConnection_Write(SocketConnection *this, void *buf, int len) { errno = 0; int sent = send(this->fd, buf, len, MSG_NOSIGNAL); if (errno == EPIPE || errno == ENOTCONN) { throw(exc, &SocketConnection_NotConnectedException); } else if (errno == ECONNRESET) { throw(exc, &SocketConnection_ConnectionResetException); } else if (sent != len) { throw(exc, &SocketConnection_LengthMismatchException); } return sent; } Assuming I want to use the kernel buffer, I could go with TCP_CORK, enable whenever it is necessary and then disable it to flush the buffer. But on the other hand, thereby the need for an additional system call arises. Thus, the usage of MSG_MORE seems more appropriate to me. I'd simply change the above send() line to: int sent = send(this->fd, buf, len, MSG_NOSIGNAL | MSG_MORE); According to lwm.net, packets will be flushed automatically if they are large enough: If an application sets that option on a socket, the kernel will not send out short packets. Instead, it will wait until enough data has shown up to fill a maximum-size packet, then send it. When TCP_CORK is turned off, any remaining data will go out on the wire. But this section only refers to TCP_CORK. Now, what is the proper way to flush MSG_MORE packets? I can only think of two possibilities: Call send() with an empty buffer and without MSG_MORE being set Re-apply the TCP_CORK option as described on this page Unfortunately the whole topic is very poorly documented and I couldn't find much on the Internet. I am also wondering how to check that everything works as expected? Obviously running the server through strace' is not an option. So the only simplest way would be to usenetcat' and then look at its `strace' output? Or will the kernel handle traffic differently transmitted over a loopback interface?

  Read the article

• Can't send client certificate via SslStream

  - by Jonathan

  I am doing an SSL3 handshake using an SslStream, but, in spite of my best efforts, the SslStream never sends a client certificate on my behalf. Here is the code: SSLConnection = new System.Net.Security.SslStream(SSLInOutStream, false, new System.Net.Security.RemoteCertificateValidationCallback(AlwaysValidRemoteCertificate), new System.Net.Security.LocalCertificateSelectionCallback(ChooseLocalCertificate)); X509CertificateCollection CC = new X509CertificateCollection(); CC.Add(Org.BouncyCastle.Security.DotNetUtilities.ToX509Certificate(MyLocalCertificate)); SSLConnection.AuthenticateAsClient("test", CC, System.Security.Authentication.SslProtocols.Ssl3, false); and then I have AlwaysValidRemoteCertificate just returning true, and ChooseLocalCertificate returning the zeroth element of the array. The code probably looks a little weird because the project is a little weird, but I think that is beside the point here. The SSL handshake completes. The issue is that instead of sending a certificate message on my behalf (in the handshake process), with the ASN.1 encoded certificate (MyLocalCertificate), the SslStream sends an SSL alert number 41 (no certificate) and then carries on. I know this from packet sniffing. After the handshake is completed, the SslStream marks IsAuthenticated as true, IsMutuallyAuthenticated as false, and its LocalCertificate member is null. I feel like I'm probably missing something pretty obvious here, so any ideas would be appreciated. I am a novice with SSL, and this project is off the beaten path, so I am kind of at a loss. P.S. 1: My ChooseLocalCertificate routine is called twice during the handshake, and returns a valid (as far as I can tell), non-null certificate both times. P.S. 2: SSLInOutStream is my own class, not a NetworkStream. Like I said, though, the handshake proceeds mostly normally, so I doubt this is the culprit... but who knows?

  Read the article

• C# .Net Serial DataReceived Event response too slow for high-rate data.

  - by Matthew

  Hi, I have set up a SerialDataReceivedEventHandler, with a forms based program in VS2008 express. My serial port is set up as follows: 115200, 8N1 Dtr and Rts enabled ReceivedBytesThreshold = 1 I have a device I am interfacing with over a BlueTooth, USB to Serial. Hyper terminal receives the data just fine at any data rate. The data is sent regularly in 22 byte long packets. This device has an adjustable rate at which data is sent. At low data rates, 10-20Hz, the code below works great, no problems. However, when I increase the data rate past 25Hz, there starts to recieve mulitple packets on one call. What I mean by this is that there should be a event trigger for every incoming packet. With higher output rates, I have tested the buffer size (BytesToRead command) immediatly when the event is called and there are multiple packets in the buffer then. I think that the event fires slowly and by the time it reaches the code, more packes have hit the buffer. One test I do is see how many time the event is trigger per second. At 10Hz, I get 10 event triggers, awesome. At 100Hz, I get something like 40 event triggers, not good. My goal for data rate is 100HZ is acceptable, 200Hz preferred, and 300Hz optimum. This should work because even at 300Hz, that is only 52800bps, less than half of the set 115200 baud rate. Anything I am over looking? public Form1() { InitializeComponent(); serialPort1.DataReceived += new SerialDataReceivedEventHandler(serialPort1_DataReceived); } private void serialPort1_DataReceived(object sender, SerialDataReceivedEventArgs e) { this.Invoke(new EventHandler(Display_Results)); } private void Display_Results(object s, EventArgs e) { serialPort1.Read(IMU, 0, serial_Port1.BytesToRead); }

  Read the article

• Problem with stack based implementation of function 0x42 of int 0x13

  - by IceCoder

  I'm trying a new approach to int 0x13 (just to learn more about the way the system works): using stack to create a DAP.. Assuming that DL contains the disk number, AX contains the address of the bootable entry in PT, DS is updated to the right segment and the stack is correctly set, this is the code: push DWORD 0x00000000 add ax, 0x0008 mov si, ax push DWORD [ds:(si)] push DWORD 0x00007c00 push WORD 0x0001 push WORD 0x0010 push ss pop ds mov si, sp mov sp, bp mov ah, 0x42 int 0x13 As you can see: I push the dap structure onto the stack, update DS:SI in order to point to it, DL is already set, then set AX to 0x42 and call int 0x13 the result is error 0x01 in AH and obviously CF set. No sectors are transferred. I checked the stack trace endlessly and it is ok, the partition table is ok too.. I cannot figure out what I'm missing... This is the stack trace portion of the disk address packet: 0x000079ea: 10 00 adc %al,(%bx,%si) 0x000079ec: 01 00 add %ax,(%bx,%si) 0x000079ee: 00 7c 00 add %bh,0x0(%si) 0x000079f1: 00 00 add %al,(%bx,%si) 0x000079f3: 08 00 or %al,(%bx,%si) 0x000079f5: 00 00 add %al,(%bx,%si) 0x000079f7: 00 00 add %al,(%bx,%si) 0x000079f9: 00 a0 07 be add %ah,-0x41f9(%bx,%si) I'm using qemu latest version and trying to read from hard drive (0x80), have also tried with a 4bytes alignment for the structure with the same result (CF 1 AH 0x01), the extensions are present.

  Read the article

• Retrieving image from database using Ajax

  - by ama

  I'm trying to read image from database with Ajax, but I could not read the xmlhttp.responseText to the img src. The image is saved as binary data in database and also retrieved as binary data. I'm using Ajax in JSP, because I want to give the user the ability to upload images and I will view the last uploaded image, on mouse over action the Ajax will be activated and get the image back, the problem is in reading the img from the response. This is the Ajax function: function ajaxFunction(path) { if (xmlhttp) { var s = path; xmlhttp.open("GET", s, true); xmlhttp.onreadystatechange = handleServerResponse; xmlhttp.send(null); } } function handleServerResponse() { if (xmlhttp.readyState == 4) { var Image = document.getElementById(Image_Element_Name); document.getElementById(Image_Element_Name).src = "data:" + xmlhttp.responseText; } } I also got exception in the server: 10415315 [TP-Processor1] WARN core.MsgContext - Error sending end packet java.net.SocketException: Broken pipe at java.net.SocketOutputStream.socketWrite0(Native Method) at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92) at java.net.SocketOutputStream.write(SocketOutputStream.java:136) at org.apache.jk.common.ChannelSocket.send(ChannelSocket.java:537) at org.apache.jk.common.JkInputStream.endMessage(JkInputStream.java:127) at org.apache.jk.core.MsgContext.action(MsgContext.java:302) at org.apache.coyote.Response.action(Response.java:183) at org.apache.coyote.Response.finish(Response.java:305) at org.apache.catalina.connector.OutputBuffer.close(OutputBuffer.java:281) at org.apache.catalina.connector.Response.finishResponse(Response.java:478) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:154) at org.apache.jk.server.JkCoyoteHandler.invoke(JkCoyoteHandler.java:200) at org.apache.jk.common.HandlerRequest.invoke(HandlerRequest.java:283) at org.apache.jk.common.ChannelSocket.invoke(ChannelSocket.java:773) at org.apache.jk.common.ChannelSocket.processConnection(ChannelSocket.java:703) at org.apache.jk.common.ChannelSocket$SocketConnection.runIt(ChannelSocket.java:895) at org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadPool.java:685) at java.lang.Thread.run(Thread.java:619) 10415316 [TP-Processor1] WARN common.ChannelSocket - processCallbacks status 2

  Read the article

• Raw FTP SSL with C#

  - by Chuck

  Hi, I'm trying to understand how SSL works. In my wish to make a small FTP client which supports SSL I've run into some problems: TcpClient FtpConnection = new TcpClient(FtpServer, FtpPort); NetworkStream FtpStream = FtpConnection.GetStream(); StreamReader FtpReader = new StreamReader(FtpStream); FtpWriter = new StreamWriter(IrcStream); send_cmd("AUTH SSL"); send_cmd is just a FtpWriter.WriteLine(text); FtpWriter.Flush(); function. My "problem" is this: First I need to make a (non-ssl) connection to the FTP, then tell it to do a ssl connection (AUTH SSL), and I would guess I then need to make a new connection - something like: TcpClient client = new TcpClient(FtpServer, FtpPort); SslStream sslStream = new SslStream(client.GetStream(), false, new RemoteCertificateValidationCallback(ValidateServerCertificate), null); try { sslStream.AuthenticateAsClient("foobar"); } catch (AuthenticationException e) { MessageBox.Show("Authentication failed - closing the connection."); client.Close(); return; } Taken from msdn. I keep dying on handshake failed due to unexpected packet format (which I've tried googling, but all say it's because the author has connected to a wrong port), which I take as: The connection is not ssl until AUTH SSL is send to it. So my question is, how would i go about making this a "hybrid" connection so I can make an SSL connection to the server? Any help is greatly appreciated!

  Read the article

• iPhone POST to PHP failing

  - by Alexander

  I have this code here: NSString *post = [NSString stringWithFormat:@"deviceIdentifier=%@&deviceToken=%@",deviceIdentifier,deviceToken]; NSData *postData = [post dataUsingEncoding:NSASCIIStringEncoding allowLossyConversion:NO]; NSString *postLength = [NSString stringWithFormat:@"%d", [postData length]]; NSMutableURLRequest *request = [[[NSMutableURLRequest alloc] init] autorelease]; [request setURL:[NSURL URLWithString:@"http://website.com/RegisterScript.php"]]; [request setHTTPMethod:@"POST"]; [request setValue:postLength forHTTPHeaderField:@"Content-Length"]; [request setValue:@"application/x-www-form-urlencoded" forHTTPHeaderField:@"Content-Type"]; [request setValue:@"MyApp-V1.0" forHTTPHeaderField:@"User-Agent"]; [request setHTTPBody:postData]; NSData *urlData = [NSURLConnection sendSynchronousRequest:request returningResponse:nil error:nil]; NSString *response = [[NSString alloc] initWithData:urlData encoding:NSASCIIStringEncoding]; which should be sending data to my PHP server to register the device into our database, but for some of my users no POST data is being sent. I've been told that this line: NSData *postData = [post dataUsingEncoding:NSASCIIStringEncoding allowLossyConversion:NO]; may be causing the problem. Any thoughts on why this script would sometimes not send the POST data? On the server I got the packet trace for a failed send and the Content-lenght came up as 0 so no data was sent at all. Thanks for any help

  Read the article

• How to limit traffic using multicast over localhost

  - by Shane Holloway

  I'm using multicast UDP over localhost to implement a loose collection of cooperative programs running on a single machine. The following code works well on Mac OSX, Windows and linux. The flaw is that the code will receive UDP packets outside of the localhost network as well. For example, sendSock.sendto(pkt, ('192.168.0.25', 1600)) is received by my test machine when sent from another box on my network. import platform, time, socket, select addr = ("239.255.2.9", 1600) sendSock = socket.socket(socket.AF_INET, socket.SOCK_DGRAM, socket.IPPROTO_UDP) sendSock.setsockopt(socket.IPPROTO_IP, socket.IP_MULTICAST_TTL, 24) sendSock.setsockopt(socket.IPPROTO_IP, socket.IP_MULTICAST_IF, socket.inet_aton("127.0.0.1")) recvSock = socket.socket(socket.AF_INET, socket.SOCK_DGRAM, socket.IPPROTO_UDP) recvSock.setsockopt(socket.SOL_SOCKET, socket.SO_REUSEADDR, True) if hasattr(socket, 'SO_REUSEPORT'): recvSock.setsockopt(socket.SOL_SOCKET, socket.SO_REUSEPORT, True) recvSock.bind(("0.0.0.0", addr[1])) status = recvSock.setsockopt(socket.IPPROTO_IP, socket.IP_ADD_MEMBERSHIP, socket.inet_aton(addr[0]) + socket.inet_aton("127.0.0.1")); while 1: pkt = "Hello host: {1} time: {0}".format(time.ctime(), platform.node()) print "SEND to: {0} data: {1}".format(addr, pkt) r = sendSock.sendto(pkt, addr) while select.select([recvSock], [], [], 0)[0]: data, fromAddr = recvSock.recvfrom(1024) print "RECV from: {0} data: {1}".format(fromAddr, data) time.sleep(2) I've attempted to recvSock.bind(("127.0.0.1", addr[1])), but that prevents the socket from receiving any multicast traffic. Is there a proper way to configure recvSock to only accept multicast packets from the 127/24 network, or do I need to test the address of each received packet?

  Read the article

• diffie-hellman ssh keyxchange

  - by Chuck

  Hi, I've set out to make a primitive SSH client in C#; you might remember me from posts such as http://stackoverflow.com/questions/2872279/c-primitive-ssh-connection-lowlevel hehe. Anyway, things are great up until the time when I initiate a DH key exchange. I've compared the traffic when I establish a ssh connection (from openssh client to openssh server), to the traffic when my client connects to the same openssh server. OpenSSH client - OpenSSH server (S for server, C for client): S: SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2\r (saying hello) C: SSH-2.0-OpenSSH_5.2\r (introducing myself) C: Key Exchange Init (0x14 = 20) S: Key Exchange Init C: Diffie-Hellman GEX Request (0x22 = 34) (with DH GEX min, number of bits and max) S: Diffie-Hellman Key Exchange Reply (with P, G, etc.) C: Diffie-Hellman GEX Init S: Diffie-Hellman GEX Reply My client - OpenSSH server: S: SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2\r (saying hello) C: SSH-2.0-Some_Name\r (introducing myself) C: Key Exchange Init (0x14 = 20) S: Key Exchange Init C: Diffie-Hellman GEX Request (0x22 = 34) (with DH GEX min, number of bits and max) and then a bogus TCP packet as reply (probably the server connection has been terminated after/upon GEX Request. I have yet to use AES128 (which I think is the encryption chosen, but I'm not sure how to verify this...), and I'm still sending in a non-compressed format, looking to get the P, G etc. values to make the DH calculations. So where I'm stranded is: RFC 4419 page 3 http://www.ietf.org/rfc/rfc4419.txt I've send SSH_MSG_KEY_DH_GEX_REQUEST, but the server does not respond SSH_MSG_KEX_DH_GEX_GROUP. Can anyone give me a little advice on what I'm not understanding here? Does the server not understand my GEX request (due to it expecting encryption, or?)? Any help is very much appreciated, thanks :)

  Read the article

• Java: Cleaning up what causes a connection reset

  - by Zombies

  There seems to be some confusion as well contradicting statements on various SO answers: http://stackoverflow.com/questions/585599/whats-causing-my-java-net-socketexception-connection-reset . You can see here that the accepted answer states that the connection was closed by other side. But this is not true, closing a connection doesn't cause a connection reset. It is cauesed by "an underlying TCP/IP error." What I want to know is if a SocketException: Connection reset means really besides "unerlying TCP/IP Error." What really causes this? As I doubt it has anything to do with the connection being closed (since closing a connection isn't an exception worthy flag, and reading from a closed connection is, but that isn't an "underlying TCP/IP error." My hypothesis is this Connection reset is caused from a server's failure to acknowledge an ACK packet (either wholly or just improperly as per TCP/IP). And that a SocketTimeoutException is generated only when no data is generated to be read (since this is thrown during a read after a certain duration, and read is waiting for data, but is not concerned with ACK packets). In other words, read() throws SocketTimeoutException if it didn't read any bytes of actual data (DATA LAYER) in its allotted time.

  Read the article

• Combining SQL Rows

  - by lumberjack4

  I've got SQL Compact Database that contains a table of IP Packet Headers. The Table looks like this: Table: PacketHeaders ID SrcAddress SrcPort DestAddress DestPort Bytes 1 10.0.25.1 255 10.0.25.50 500 64 2 10.0.25.50 500 10.0.25.1 255 80 3 10.0.25.50 500 10.0.25.1 255 16 4 75.48.0.25 387 74.26.9.40 198 72 5 74.26.9.40 198 75.48.0.25 387 64 6 10.0.25.1 255 10.0.25.50 500 48 I need to perform a query to show 'conversations' going on across a local network. Packets going from A - B is part of the same conversations as packets going from B - A. I need to perform a query to show the on going conversations. Basically what I need is something that looks like this: Returned Query: SrcAddress SrcPort DestAddress DestPort TotalBytes BytesA->B BytesB->A 10.0.25.1 255 10.0.25.50 500 208 112 96 75.48.0.25 387 74.26.9.40 198 136 72 64 As you can see I need the query (or series of queries) to recognize that A-B is the same as B-A and break up the byte counts accordingly. I'm not a SQL guru by any means but any help on this would be greatly appreciated.

  Read the article

• Where are the real risks in network security?

  - by Barry Brown

  Anytime a username/password authentication is used, the common wisdom is to protect the transport of that data using encryption (SSL, HTTPS, etc). But that leaves the end points potentially vulnerable. Realistically, which is at greater risk of intrusion? Transport layer: Compromised via wireless packet sniffing, malicious wiretapping, etc. Transport devices: Risks include ISPs and Internet backbone operators sniffing data. End-user device: Vulnerable to spyware, key loggers, shoulder surfing, and so forth. Remote server: Many uncontrollable vulnerabilities including malicious operators, break-ins resulting in stolen data, physically heisting servers, backups kept in insecure places, and much more. My gut reaction is that although the transport layer is relatively easy to protect via SSL, the risks in the other areas are much, much greater, especially at the end points. For example, at home my computer connects directly to my router; from there it goes straight to my ISPs routers and onto the Internet. I would estimate the risks at the transport level (both software and hardware) at low to non-existant. But what security does the server I'm connected to have? Have they been hacked into? Is the operator collecting usernames and passwords, knowing that most people use the same information at other websites? Likewise, has my computer been compromised by malware? Those seem like much greater risks. What do you think?

  Read the article

• Shutdown and WakeUp Script C#

  - by Stephen Murby

  Hiya I am very new to C#, infact this is basically my first task set by work whilst i learn the language. Yes i am also new to programming, be gentle :). Context: My script needs to query active directory, grab of OU's and put them to a combo box in a form. Next query ActDir for a list of machines in a selected OU (Done this in a vbscript already) Next query the machines in turn for there IP, and MAC addresses.(Done this in a vbscript already) Next needs to shut those machines down(Done this in a vbscript already) and dump all the machine and NIC info to a txt file The other half of the script grabs the info for the machines out of the text file and sends them a magic packet to wake them up. The shutdown section i have already written a VBscript for, but decided it wasn't future prrof, and i was learninc C# at home, so figured it was the best option to start over with. Im not looking for anyone to write this for me, but if anyone had any pointers on where to go for information etc. . . It would be more than appreciated :)

  Read the article

• moving audio over a local network using GStreamer

  - by James Turner

  I need to move realtime audio between two Linux machines, which are both running custom software (of mine) which builds on top of Gstreamer. (The software already has other communication between the machines, over a separate TCP-based protocol - I mention this in case having reliable out-of-band data makes a difference to the solution). The audio input will be a microphone / line-in on the sending machine, and normal audio output as the sink on the destination; alsasrc and alsasink are the most likely, though for testing I have been using the audiotestsrc instead of a real microphone. GStreamer offers a multitude of ways to move data round over networks - RTP, RTSP, GDP payloading, UDP and TCP servers, clients and sockets, and so on. There's also many examples on the web of streaming both audio and video - but none of them seem to work for me, in practice; either the destination pipeline fails to negotiate caps, or I hear a single packet and then the pipeline stalls, or the destination pipeline bails out immediately with no data available. In all cases, I'm testing on the command-line just gst-launch. No compression of the audio data is required - raw audio, or trivial WAV, uLaw or aLaw encoding is fine; what's more important is low-ish latency.

  Read the article

• How to configure outgoing connections from an SQL stored procedure?

  - by Peter Vestberg

  I am working on a .NET project which uses Microsoft SQL server. In this project, I need a CLR stored procedure (written in C#) that uses a remote web service. So, when the stored procedure is executed on the SQL server, it makes web service calls and thus sends packets to a remote location. The problem is that when executing the SP I get: "System.Net.WebException: The request failed with HTTP status 403: Forbidden." The database user has full permission, the deployed CLR assembly and SP are even marked "unsafe", I tried signing it etc., so any of that is not causing the problem. When I am executing the very same C# code, but from a simple console application instead of as a SP, it all works fine. So I started to suspect a network related problem and had a packet sniffer running when executing both the SP and the console app version. What I realized was that the packets sent out had different destination IP addresses: the console app sent the packets directly to the web service IP while the SP sent the packets to a proxy server we use in our company. Due to network policies the latter is not allowed and that explains the "403 Forbidden" exception. So my question boils down to this: How can I configure the SP/MS SQL server to NOT use that proxy? I want it to send the packets directly to the web service IP, just like the test console app. (again, the C# code is the same , so it's not a programming matter). I've disabled all proxy settings in Internet Explorer in case the SQL server inherits these settings or something. However, no luck. Any help would be greatly appreciated! Best regards, Peter

  Read the article

• Why would a WebService return nulls when the actual service returns data?

  - by Jerry

  I have a webservice (out of my control) that I have to talk to. I also have a packet-sniffer on the line, and (SURPRISE!!!) the developers of the webservice aren't lying. They are actually sending back all of the data that I requested. But the web-service code that is auto-generated from the WSDL file is giving me "null" as a value. I used their WSDL file to generate my Web Reference. I checked my data types with the datatypes that the WSDL file has declared. And I used the code as listed below to perform the calls: DT_MaterialMaster_LookupRequest req = new DT_MaterialMaster_LookupRequest(); req.MaterialNumber = "101*"; req.DocumentNo = ""; req.Description = "Pipe*"; req.Plant = "0000"; MI_MaterialMaster_Lookup_OBService srv = new MI_MaterialMaster_Lookup_OBService(); DT_MaterialMaster_Response resp = srv.MI_MaterialMaster_Lookup_OB(new DT_MaterialMaster_LookupRequest[] { req }); // Note that the response here is ALWAYS null!! Console.WriteLine(resp.Status); The resp object is an actual object. It was generated properly. However, the Status and MaterialData fields are always null. When I call the web service, I've placed a packet-sniffer on the line, and I can see that I've sent the following (linebreaks and indentions for my own sanity): <?xml version="1.0" encoding="utf-8"?> <soap:Envelope xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema"> <soap:Body> <MT_MaterialMaster_Lookup xmlns="http://MyCompany.com/SomeCompany/mm/MaterialMasterSearch"> <Request xmlns=""> <MaterialNumber>101*</MaterialNumber> <Description>Pipe*</Description> <DocumentNo /> <Plant>0000</Plant> </Request> </MT_MaterialMaster_Lookup> </soap:Body> </soap:Envelope> The response that they send back SEEMS to be a valid response (linebreaks and indentions for my own sanity): <SOAP:Envelope xmlns:SOAP='http://schemas.xmlsoap.org/soap/envelope/'> <SOAP:Header /> <SOAP:Body> <n0:MT_MaterialMaster_Response xmlns:n0='http://MyCompany.com/SomeCompany/mm/MaterialMasterSearch' xmlns:prx='urn:SomeCompany.com:proxy:BRD:/1SAI/TAS4FE14A2DE960D61219AE:701:2009/02/10'> <Response> <Status>No Rows Found</Status> <MaterialData /> </Response> </n0:MT_MaterialMaster_Response> </SOAP:Body> </SOAP:Envelope> The status shows that it actually received data... but the resp.Status and resp.MaterialData fields are always null. What have I done wrong? UPDATE: The WSDL file is defined as: <?xml version="1.0" encoding="utf-8"?> <wsdl:definitions xmlns:p1="http://MyCompany.com/SomeCompany/mm/MaterialMasterSearch" name="MI_MaterialMaster_Lookup_AutoCAD_OB" targetNamespace="http://MyCompany.com/SomeCompany/mm/MaterialMasterSearch" xmlns:wsdl="http://schemas.xmlsoap.org/wsdl/"> <wsdl:types> <xsd:schema xmlns="http://MyCompany.com/SomeCompany/mm/MaterialMasterSearch" targetNamespace="http://MyCompany.com/SomeCompany/mm/MaterialMasterSearch" xmlns:xsd="http://www.w3.org/2001/XMLSchema"> <xsd:element name="MT_MaterialMaster_Response" type="p1:DT_MaterialMaster_Response" /> <xsd:element name="MT_MaterialMaster_Lookup" type="p1:DT_MaterialMaster_Lookup" /> <xsd:complexType name="DT_MaterialMaster_Response"> <xsd:sequence> <xsd:element name="Status" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">d48d03b040af11df99e300145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element maxOccurs="unbounded" name="MaterialData"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa040a511df843700145eccb24e</xsd:appinfo> </xsd:annotation> <xsd:complexType> <xsd:sequence> <xsd:element name="MaterialNumber" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa140a511df848500145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="Description" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa240a511df95bf00145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="DocumentNo" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa340a511dfb23700145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="UOM" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">3b5f14c040a611df9fbe00145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="Hierarchy" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa440a511dfc65b00145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="Plant" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">d48d03b140af11dfb78e00145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="Procurement" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">d48d03b240af11dfb87b00145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> </xsd:sequence> </xsd:complexType> </xsd:element> </xsd:sequence> </xsd:complexType> <xsd:complexType name="DT_MaterialMaster_Lookup"> <xsd:sequence> <xsd:element maxOccurs="unbounded" name="Request"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa040a511df843700145eccb24e</xsd:appinfo> </xsd:annotation> <xsd:complexType> <xsd:sequence> <xsd:element minOccurs="0" name="MaterialNumber" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa140a511df848500145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="Description" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa240a511df95bf00145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="DocumentNo" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa340a511dfb23700145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> <xsd:element minOccurs="0" name="Plant" type="xsd:string"> <xsd:annotation> <xsd:appinfo source="http://SomeCompany.com/xi/TextID">64908aa440a511dfc65b00145eccb24e</xsd:appinfo> </xsd:annotation> </xsd:element> </xsd:sequence> </xsd:complexType> </xsd:element> </xsd:sequence> </xsd:complexType> </xsd:schema> </wsdl:types> <wsdl:message name="MT_MaterialMaster_Lookup"> <wsdl:part name="MT_MaterialMaster_Lookup" element="p1:MT_MaterialMaster_Lookup" /> </wsdl:message> <wsdl:message name="MT_MaterialMaster_Response"> <wsdl:part name="MT_MaterialMaster_Response" element="p1:MT_MaterialMaster_Response" /> </wsdl:message> <wsdl:portType name="MI_MaterialMaster_Lookup_AutoCAD_OB"> <wsdl:operation name="MI_MaterialMaster_Lookup_AutoCAD_OB"> <wsdl:input message="p1:MT_MaterialMaster_Lookup" /> <wsdl:output message="p1:MT_MaterialMaster_Response" /> </wsdl:operation> </wsdl:portType> <wsdl:binding name="MI_MaterialMaster_Lookup_AutoCAD_OBBinding" type="p1:MI_MaterialMaster_Lookup_AutoCAD_OB"> <binding transport="http://schemas.xmlsoap.org/soap/http" xmlns="http://schemas.xmlsoap.org/wsdl/soap/" /> <wsdl:operation name="MI_MaterialMaster_Lookup_AutoCAD_OB"> <operation soapAction="http://SomeCompany.com/xi/WebService/soap1.1" xmlns="http://schemas.xmlsoap.org/wsdl/soap/" /> <wsdl:input> <body use="literal" xmlns="http://schemas.xmlsoap.org/wsdl/soap/" /> </wsdl:input> <wsdl:output> <body use="literal" xmlns="http://schemas.xmlsoap.org/wsdl/soap/" /> </wsdl:output> </wsdl:operation> </wsdl:binding> <wsdl:service name="MI_MaterialMaster_Lookup_AutoCAD_OBService"> <wsdl:port name="MI_MaterialMaster_Lookup_AutoCAD_OBPort" binding="p1:MI_MaterialMaster_Lookup_AutoCAD_OBBinding"> <address location="http://bxdwas.MyCompany.com/XISOAPAdapter/MessageServlet?channel=:AutoCAD:SOAP_SND_Material_Lookup" xmlns="http://schemas.xmlsoap.org/wsdl/soap/" /> </wsdl:port> </wsdl:service> </wsdl:definitions>

  Read the article

< Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >